PREMIUM SNOWMOBILE LIFT PART # 9015 ASSEMBLY INSTRUCTIONS PARTS LIST Qty
Description
1
Base Piece
1
Stem Piece # 1 - Black
1
Stem Piece # 2 - Chrome
1
Lift Handle w/Hook
1 EA
Short Bolt Long Bolt/Washer/Nut
1 EA
Clevis/Cotter Pin Take stem piece #2 and insert it into stem piece #1. Make sure the lock tab with the clevis pin for the handle is facing towards the back of the stand. Adjust to the height you require and insert the long bolt through both stems. Install the washer and the nut and tighten.
Start with the base piece. Make sure that the bolt hole in the base is facing away from you and that the longer portion of the base is to the front.
Take stem piece # 1 and insert it into the base. Insert the short bolt into the base and tighten until the stem is secure.
Insert the handle into the slot in stem #2 with the hook facing the long portion of the base. Insert the Clevis pin through the stem and handle. Insert cotter pin through clevis.
When you are ready to use the lift – pull the handle up, attach the hook to your sled. Push down on the handle - the hole in the handle lines up with the hole on the lock tab. Insert the lock pin through the 2 holes to secure. If the track is not off the ground – you may need to adjust the height of Stem # 2.
IGNITION PRODUCTS WILL NOT BE RESPONSIBLE FOR PERSONAL INJURY OR DAMAGE TO PERSONAL PROPERTY DUE TO INCORRECT ASSEMBLY OR USE. FOR MORE INFORMATION CONTACT IGNITION PRODUCTS @ (905) 683-3785
SOULÉVATEUR HAUTE QUALITÉ DE MOTONEIGE
PIÈCE # 9015
INSTRUCTIONS DE MONTAGE LISTE DES PIÈCES Qté
Description
1
Chassis
1
Tube # 1 - Noire
1
Tube # 2 - Chrome
1
Poignée de levage a/crochet
1 EA
Boulon court Boulon long /Rondelles/Écrou
1 EA
Chape/Clavette Prenez le tube #2 et insérez-la dans le tube #1 . Assurez –vous que l’attache de verrouillage avec la chape pour la poignée fait face à l’arrière du socle. Ajustez à la hauteur requise et insérez le boulon long au travers des deux tubes. Installez la rondelle et l’écrou, puis serrez.
Commencez par le châssis. Assurez-vous que le trou pour le boulon dans le châssis est éloigné de vous et que la partie la plus longue du châssis est à l’avant.
Prenez le tube #1 et insérez la dans le châssis. Insérez le boulon court dans le châssis et serrez-le tant que la tige soit solide.
Insérez la poignée dans la fente du tube #2 avec le crochet faisant face à la longue portion du socle. Insérez la chape au travers du tube et de la poignée. Insérez la clavette dans la chape.
Quand vous êtes prêt à utiliser le soulévateur- levez la poignée vers le haut, attachez le crochet à la motoneige. Poussez vers le bas sur la poignée – le trou dans la poignée aligné avec le trou dans l’attache de verrouillage. Insérez la goupille de verrouillage au travers des deux trous pour sécuriser. Si la chenille n’est pas décollée du sol – vous pouvez avoir besoin d’ajuster la hauteur de la tige #2.
IGNITION PRODUCTS N’EST RESPONSABLE DES BLESSURES PERSONNELLES OU DES DOMMAGES À LA PROPRIÉTÉ CAUSÉS PAR UN MONTAGE OU UNE UTILISATION INADÉQUATE. POUR PLUS D’INFORMATION, CONTACTEZ IGNITION PRODUCTS @ (905) 683-3785