JCB WHEEL LOADER | 406 MAX ENGINE POWER: 62 hp (46kW)
MAX OPERATING WEIGHT: 11,204 lb (5,082 kg)
MAX LOADER CAPACITY: 1.8 yd3 (1.4 m3)
D
C
F
B
E
A
STATIC DIMENSIONS
ft-in (mm)
Front Axle Weight*
lb (kg)
A
Overall Length with Standard Bucket
16-10 (5133)
Rear Axle Weight*
lb (kg)
7716 (3500)
B
Wheel Base
6-11 (2100)
Operating Weight (includes standard bucket)
lb (kg)
10,877 (4934)
3161 (1434)
C Min Ground Clearance
1-1 (330)
Inside Radius
ft-in (mm)
6-7 (2010)
D Height Over Cab
8-2 (2500)
Maximum Radius Over Standard Bucket
ft-in (mm)
15-8 (4160)
E
Max Bucket Width
6-3 (1900)
Maximum Radius Over Tires
ft-in (mm)
12-6 (3800)
F
Wheel Track
4-7 (1390)
Articulation Angle Max Width Across Tires
degrees ft-in (mm)
±40° 5-9 (1761)
Note: Dimensions assume fitment of standard JCB 12.5x18 wheel and tires. *Axle weights based on unloaded bucket in carry position. 3
1.0yd (0.8m3) bucket
JCB WHEEL LOADER | 406 ENGINE
SERVICE FILL CAPACITIES
Type
4 Cylinder Diesel
gal (liters)
Make
Deutz
Hydraulic and Transmission System
18.5 (70)
Model
D2011 L04i
Fuel Tank
21 (80)
Capacity
220.9 (3.62)
Engine Oil Sump
3.1 (12)
in3 (l)
Bore
in (mm)
3.7 (96)
Axle Oil (front) Including Hubs
1.16 (4.4)
Stroke
in (mm)
4.9 (125)
Axle Oil (rear) Including Hubs and Drop Box
1.6 (6.05)
Aspiration
Naturally Aspirated
Cylinders
4
ELECTRICAL SYSTEM
Power Rating Gross Power to SAE J1995/ISO 14396
hp (kW) @ 2500 rpm
62 (46)
Net Power to J1349/EEC 80/1269
hp (kW) @ 2500 rpm
58 (43.5)
lbf ft (Nm) @ 1700 rpm
140 (190)
Alternator Output Battery Capacity
Torque Rating Gross Torque
System Voltage
Emission Certification
Cold Cranking Capacity
V
12
Ah
80
Ah
105
CCA
870
EPA T3 (EU Stg 3)
STANDARD EQUIPMENT TRANSMISSION
Loader: Parallel lift geometry; Quickhitch with hydraulic pin locking.
Type
Hydrostatic
Make
Rexroth
Model
A6VM
Low Range
mph (km/h)
3.8 (6)
High Range
mph (km/h)
12.5 (20)
Engine: 4 cylinder oil cooled diesel engine; dual stage cyclonic engine air filter; Single bowl fuel filter; Fan guards. Transmission: Two position electric switch; Neutral start; Disconnect on footbrake (inching capability). Axles: Straight beam axles. Brakes: In board oil immersed brakes with combined handbrake. Electrical: Road lights front and rear; Reverse lights; 80 amp alternator; battery isolator switch. Hydraulics: Gear pump with priority steer; Emergency steer back up; 3 spool loader circuit.
AXLES Type
Straight Beam
Make
Dana Spicer
Model
111
Overall Axle Ratio / Drop Box Ratio
19.3 / 2.1
Chassis Angle Oscillation
degrees
Pump Max Flow Pump Max Pressure
gal/min (l/min) psi (bar)
OPTIONAL EQUIPMENT Gear 16 (60) 3335 (230)
Hydraulic Cycle Times at Full Engine Revs:
Seconds
Arms Raise (full bucket)
4.9
Bucket Dump (full bucket)
3.5
Arms Lower (empty bucket)
3.1
Total Cycle
11.5
Max Auxiliary Flow
gal/min (l/min)
Bodywork: Front and rear fenders; Side and rear access panels; Fixed bottom steps; Full width rear counterweight; Recovery hitch; Lifting lugs; Engine sump kit, 12.5 R18 JCB tires.
±10°
LOADER HYDRAULICS Pump Type
Cab: ROPS/FOPS safety structure; Fully adjustable seat; Interior light; Safety glass; Electronic monitoring with warning panel; Front and rear screen wash/wipe; 3 speed heater fan with replaceable filters; LH opening door; Up and over handbrake with catch; Laminated screen; Loader control isolator; Door lock back system; Storage tray.
16 (60)
Limited slip differential axles front/rear; 3 HBCV; Epoxy coated cooling pack; Smooth ride system; Air suspension seat; Creep speed; 4th spool auxiliary circuit; High spec cab; Front and rear working lights; Fire extinguisher; Face level fan; Radio installation kit; Reverse alarm; Rotating beacon; Adjustable steering column analogue gauges; Reversing lights and rear fog lights; Sun visor; Biodegradable oil; Sliding window; 407/409 adapter plate; Single level joystick control; Foward/reverse switch on joystick control lever, air conditioning, canopy.
TIRES 12.5/80 R18 SGL, 335/80 R18 XM27, 335/80 R18 XZSL.
JCB WHEEL LOADER | 406 LOADER DIMENSIONS
PALLET FORK DIMENSIONS
O
FF P
BF
L
N K J
M
EF
H
AF DF
R
G
D
CF
E S A
PALLET FORK DIMENSIONS
C B
Loader Dimensions: Assumes Fitment of 12.5x18 Tires.
LOADER DIMENSIONS
Bucket
General
General
Light
Light
6-in-1 Clam
Purpose
Purpose
Duty
Duty
Shovel
Capacity Heaped
yd3
Material Density
lb/yd3 (kg/m3)
Empty Bucket Weight
(m3)
lb (kg)
1.0 (0.8)
1.3 (1.0)
1.6 (1.2)
1.8 (1.4)
1.0 (0.75)
3400 (2050)
2688 (1620)
2190 (1320)
1858 (1120)
3484 (2100)
633 (287)
710 (322)
778 (353)
846 (384)
959 (435)
Bucket Equipment
Teeth or
Teeth or
Teeth or
Teeth or
Teeth or
Toeplate
Toeplate
Toeplate
Toeplate
Toeplate
Static Tipping Load, Straight (EN)
lb (kg)
9458 (4290)
9268 (4212)
9079 (4118)
8986 (4076)
9028 (4095)
Static Tipping Load, Full Turn 40° (ISO) lb (kg)
7275 (3300)
7143 (3240)
6984 (3168)
6914 (3136)
6945 (3150)
Payload 50%
Max Tearout Force
ft-in (mm)
Fork Carriage Width
4-5 (1345)
Length of Tines
3-11 (1200)
AF Reach at Ground Level
2-4 (710)
BF Max Reach Arms Horizontal
4-1 (1232)
CF Below Ground Level
0-3 (84)
DF Height Arms Horizontal
4-8 (1426)
EF Max Height
9-11 (3012)
FF Reach at Max Height
1-8 (506)
Full Turn Tipping Load (500 mm load centers)
lb (kg)
5688 (2580)
Operating Load (60%)
lb (kg)
3412 (1548)
Operating Load (80%)
lb (kg)
4550 (2064)
LOADER DIMENSIONS
lb (kg)
3638 (1650)
3571 (1620)
3492 (1584)
3456 (1568)
3472 (1575)
B
ft-in (mm)
14-4 (4369)
lbf (kN)
9420 (41.9)
8205 (36.5)
7238 (32.2)
6676 (29.7)
9420 (41.9)
C Wheel Base
ft-in (mm)
6-11 (2100)
Bucket Width
ft-in (mm)
6-3 (1900)
6-3 (1900)
6-3 (1900)
6-3 (1900)
6-3 (1900)
D Minimum Ground Clearance
ft-in (mm)
1-1 (330)
Outside Turning Circle Radius
ft-in (mm)
13-8 (4160)
13-9 (4185)
13-10 (4210)
13-10 (4229)
13-8 (4160)
F
Height Over Cab
ft-in (mm)
8-2 (2500)
A Total Length (bucket flat on ground) ft-in (mm)
16-10 (5133)
17-2 (5233)
17-9 (5333)
18-9 (5408)
16-10 (5133)
J
Load Over Height
ft-in (mm)
8-10 (2991)
L Lift Height Max
ft-in (mm)
13-7 (4140)
13-1 (4246)
14-6 (4333)
14-7 (4438)
13-8 (4157)
K
Hinge Pin Height
ft-in (mm)
10-3 (3131)
E Digging Depth
ft-in (mm)
0-4 (105)
0-4 (105)
0-4 (105)
0-4 (105)
0-4 (105)
O Roll Back at Full Height
degrees
56°
H Dump Height
ft-in (mm)
8-2 (2489)
7-11 (2418)
7-8 (2348)
7-6 (2295)
8-2 (2489)
P
Dump at Full Height
degrees
45°
M Reach at Max Height @ 45° Dump ft-in (mm)
2-6 (764)
2-9 (835)
3-0 (905)
3-2 (958.5)
2-6 (764)
R
Rollback at Carry
degrees
54°
4-11 (1494)
4-10 (1465)
5-2 (1635)
5-6 (1689)
4-11 (1494)
S
Dump at Minimum Height
degrees
67°
N Max Reach @ 45° Dump
Operating Weight
ft-in (mm) lb (kg)
10,870 (4934) 10,950 (4969) 11,020 (5000) 11,090 (5031) 11,200 (5082)
Length to Loader Pin
JCB WHEEL LOADER | 406
A GLOBAL COMMITMENT TO QUALITY JCB’s total commitment to its products and customers has helped it grow from a one-man business into one of the world’s largest manufacturers of backhoe loaders, crawler excavators, wheeled excavators, telescopic handlers, wheeled loaders, dump trucks, rough terrain fork lifts, industrial fork lifts, mini/midi excavators, skid steer loaders and tractors. By making constant and massive investments in the latest production technology, the JCB factories have become some of the most advanced in the world. By leading the field in innovative research and design, extensive testing and stringent quality control, JCB machines have become renowned all over the world for performance, value and reliability. And with an extensive dealer sales and service network in over 150 countries, we aim to deliver the best customer support in the industry. Through setting the standards by which others are judged, JCB has become one of the world’s most impressive success stories.
JCB Headquarters Savannah, 2000 Bamford Blvd, Savannah, GA 31322 Tel: (912) 447-2000 Fax: (912) 447-2299 www.jcb.com JCB reserves the right to change design, materials and/or specifications without notice. Specifications are applicable to units sold in the United States and Canada. The JCB logo is a registered trademark of J C Bamford Excavators Ltd. DWUSA 2979 12/11