KAN-therm Steel SYSTEM ISO 9001 : 2000
TECHNOLOGY OF SUCCESS
Contents
Page
KAN-therm Steel System - technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 KAN-therm Steel System - fitting assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 KAN-therm Steel System - tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 KAN-therm Steel System - detailed information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 KAN-therm Steel System - elongation and thermal conductivity data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 KAN-therm Steel System - recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Screw connections and joining with other KAN-therm Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 KAN-therm Steel System - pipeline assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 KAN-therm Steel System - fixed (PS) and slidable (SP) points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 KAN-therm Steel System - elongation compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 KAN-therm Steel System - "L", "Z", and "U" compensator selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 KAN-therm Steel System - pressure drops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 KAN-therm Steel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 KAN-therm System - tools for Steel and Inox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
This catalogue is valid from May 1st, 2008 and replaces all its previous editions. KAN Sp. z o.o. reserves the right to change contents of this catalogue. Š Copyright KAN Sp. z o.o. All rights reserved. Copyrights include texts, pictures and their lay-out in KAN Sp. z o.o. publications.
21
KAN-therm Steel System - technical information
KAN-therm Steel System is a system of carbon steel tubes and fittings of diameters 15 to 108 mm. The tubes and fittings produced of high quality carbon steel covered with thin zinc layer which protects external surface agains corrosion.
KAN-therm Steel System - modern connection technology "Press" technology used in KAN-therm Steel System enables to make fast and reliable connections by pressing fittings using widely available press tools, and to eliminate twisting and welding of individual elements. The system permits a very quick assembly even when using pipes and fittings of large diameters. KAN-therm Steel System pipes and fittings are made of thin−walled steel, which significantly decreases weight of individual elements and facilitates system assembly. Connecting elements in "press" technology allows to obtain connections of minimized pipe section narrowing, which significantly decreases waste of system pressure and creates excellent hydraulic conditions.
KAN-therm Steel System - long-lasting connection technology Connection leak tightness in KAN-therm Steel System is provided by special O−Ring seals and a three−point "M" type jaw.
KAN-therm Steel System - application possibilities heating "closed" systems, ice water systems.
KAN-therm Steel System - advantages quick and reliable system assembly without welding and twisting, wide range of pipe and fitting diameters up to 108 mm, wide range of working temperatures: from −20°C to 120°C, high pressure resistance up to 16 bar, compatible with plastic systems KAN-therm Press and Push, lightweight pipes and fittings, system high aesthetics, resistance to mechanical damage.
- 73 -
KAN-therm Steel System - technical information
21
KAN-therm Steel System - fitting assembly
1. Pipe cutting Pipes should be cut perpendicular to their axes using tube cutter (full cut, with no breaking off nicked pipe segments). Using other tools is permissible provided the cut is perpendicular and cut edges are not damaged (no breaking off, no material decrements or other deformations of pipe section). Tools that emit a lot of heat, e.g. a torch, an angle grinder, etc., cannot be used.
3. Marking the insertion depth of the pipe into the fitting In order to obtain proper connection strength it is necessary to keep the correct insertion depth of the pipe into the fitting (it should be slid home). To make sure the pipe is properly slid into the fitting during pressing, mark the required insertion depth with a pen marker on the pipe or the fitting. Also, there are special markers for marking the insertion depth (no fitting check−in).
- 74 -
2. Pipe beveling Using a hand operated stripping tool, bevel outside and inside the tip of the cut pipe, and remove all file dust that can damage an O−Ring during assembly.
4. Control Before assembly, check visually there is an O−Ring in the fitting, whether it is not damaged, and whether there are no file dust or any other sharp objects which can cause damage to the O−Ring during assembly.
KAN-therm Steel System - technical information
21
∅[mm] 15 18 22 28 35 42 54 76 88 108
A [mm] 20 20 21 23 26 30 35 52,5 / 55* 60 / 63* 74 / 77*
dmin [mm] 10 10 10 10 10 20 20 40 50 50
Table 1. Pipe insertion depth into the fitting and minimum distance between pressed fittings
Pic. 1A. Pipe insertion depth into the fitting, dmin − minimum distance between fittings because of
*concerning the new design of fittings
press correctness
5. Pipe and fitting assembly Before making the connection, axially insert the pipe into the fitting to a marked depth. To make the assembly easier it is possible to slightly twist the pipe in relation to the fitting. In the case of making many connections (inserting pipes into fittings and pressing) it is very important to watch the pipe insertion depth. To do so watch previously made markings on pipes near fitting edges. To make the assembly easier it is imperative to keep minimum assembly distances presented in Table 2 and Pictures 2, 3, and 4. Table 2. Minimum assembly distances
∅ [mm]
Pic. 2
Pic. 3
a [mm]
b [mm]
a [mm]
b [mm]
c [mm]
15
56
20
75
25
28
18
60
20
75
25
28
22
65
25
80
31
35
28
75
25
80
31
35
35
75
30
80
31
44
42
140/115*
60/75*
140/115*
60/75*
75
54
140/120*
60/85*
140/120*
60/85*
85
76
140*
110*
165*
115*
115
88
150*
120*
185*
125*
125
108
170*
140*
200*
135*
135
*applies to four−part pressing jaws
Pic. 2
Pic. 3
Pic. 4
- 75 -
KAN-therm Steel System - technical information
21
6. Pressing Before starting pressing check efficiency of tools. It is recommended to use press tools and pressing jaws offered by KAN-therm System. Always choose pressing jaw of appropriate size for the connection diameter. Pressing jaw should be placed on the fitting so that its profile precisely clasps the place where an O−Ring is embedded in the fitting (the convex part of the fitting). When the press tool is started, the process of pressing is performed automatically and cannot be stopped. Because of forces that appear during pressing, there are two types of press tools designed for pipes of diameter 15−54 mm and 76.1−108 mm. In the case the plumber has different press tools and jaws than the ones offered by KAN-therm, he should consult their possible use with KAN Company in advance.
Pic. 5. A fitting before and after pressing
KAN-therm Steel System - tools
Tools for diameters of 15 −54 mm.
- 76 -
Tools for diameters of 76,1 −108 mm.
KAN-therm Steel System - technical information
21
KAN-therm Steel System - detailed information Pipes and fittings - material The carbon steel RSt 34−2 (1.0034 acc. DIN EN 10305−3), the tubes externaly zinc coated (Fe/Zn 88), zinc layer thickness 7−15 μm. O-Rings O-Ring
Properties and work parameters
Application
EPDM (butyl rubber)
color: black max. working pressure: 16 bar working temperature: −20°C to 110°C short duration: 120°C
potable water hot water treated water (softened, decalcified,
color: green max. working pressure: 16 bar working temperature: −30°C to 180°C short duration: 230°C
solar systems compressed air fuel oil vegetable fat engine fuels
distilled, with glycol)
compressed air (dry)
FPM / Viton (fluorine rubber)
Fittings come with standard EPDM O-Rings. For special uses Viton O-Rings are delivered separately.
KAN-therm Steel System - elongation and thermal conductivity data Linear elongation coefficient
Elongation of 4 m segment at 60°C
Material
[mm] [W/(m2×K)]
[mm/(m×K)]
Steel
Thermal conductivity
0,012
2,88
58
KAN-therm Steel System - recommendations KAN-therm Steel − steel pipes cannot be bent when warm. Cold bending is permissible provided the minimum bending radius is kept (R=3.5×dz). Do not expose pipe external surface to prolonged direct moisture during storage and use. Pipes over ∅54 mm should not be bent. Use ready−made pipe bends and 90° and 45° elbows offered by KAN-therm Steel System. It is not allowed to cut pipes using tools which emit a lot of heat, e.g. torches and cutting−off machines. To cut KAN-therm Steel pipes use only tube cutters (hand operated and mechanical). Systems filled with water should not be emptied. In the case a system has to be emptied after a pressure test, it is advised to perform pressure tests using compressed air. When KAN-therm Steel pipes are concealed in walls, pipes should be insulated because of thermal elongation compensation and construction chemicals. In the case of transporting chemical substances the possible use of KAN-therm Steel pipes should be consulted with KAN Technical Department. KAN-therm Steel System installations require potential equalization.
- 77 -
KAN-therm Steel System - technical information
21
Screw connections and joining with other KAN-therm Systems Besides "press" fittings, KAN-therm Steel offers the whole range of male and female thread fittings. Because of steel fitting conical threads, it is only possible to join KAN-therm Steel brass fitting male threads with KAN-therm System steel fitting female threads. Such connections should be sealed by small amounts of tow. PTFE (teflon) tape and other leak stoppers that can release chlorides soluble in water should not be used. KAN-therm Steel System fittings should not be directly connected with stainless steel − brass or bronze separating elements of minimum length of 50 mm should be used.
Pic. 6. Correct screw connection.
KAN-therm Steel System - pipeline assembly Maximum distances between attachment points are presented in Table 3. Table 3. Maximum distances between pipeline attachment points Pipe diameter [mm]
Distance between attachment points [m]
15
1,25
18
1,50
22
2,00
28
2,25
35
2,75
42
3,00
54
3,50
76,1
4,25
88,9
4,75
108
5,00
Attachment points can be done as: slidable points SP − slidable points should enable free axial motion of the pipeline (caused by thermal motions), that is why they shouldn’t be fixed next to the fittings (minimal distance from fitting flange must be higher than maximum elongated of pipeline). The slidable point can be made as “unscrewed” metal clamps with rubber pads, fixed points FP − to make fixed point, the metal clamp with rubber pad should be used, it should enables precise and reliability stabilization of the pipe on the whole circuit. The metal clump should be maximally tighten on the pipe, attachment points preventing the pipeline from moving downwards; used if the pipeline movement on compensation arm length was blocked by required SP position.
- 78 -
KAN-therm Steel System - technical information
21
KAN-therm Steel System - fixed (PS) and slidable (SP) points fixed points should prevent any movement of pipelines and should be fixed next to fittings (at both sides of a fitting, e.g. coupling, tee connection); fixed or slidable points cannot be fixed directly onto fittings; when fixing FPs near tee connections make sure that clamps blocking the pipeline are not fixed onto branches of smaller diameters than one dimension in relation to the pipeline (forces induced by large diameter pipes can damage small diameters); SPs enable only axial motion of the pipeline (they should be treated as fixed points for perpendicular direction to the pipeline axis) and should be made by clamps; SPs should not be fixed next to fittings because this may block thermal motions of the pipeline; remember that SPs prevent the pipeline from moving transverse to its axis and that is why their position may determine compensation arms length.
KAN-therm Steel System - elongation compensation Along with water temperature rise Δt, pipelines become elongated by ΔL value. Thermal elongation ΔL causes pipeline deformation on expansion compensation length A. Expansion compensation length A should not cause excessive stresses in the pipeline and depends on the pipeline external diameter, thermal elongation (ΔL), and a linear expansion coefficient for a given material. Elongations (ΔL) in function of pipe length (L) and temperature rise (Δt) are presented in Table 4.: Table 4. Total length variation ΔL [mm] – KAN-therm Steel Δt [°C] L [m] 10
20
30
40
50
60
70
80
90
100
1
0,12
0,24
0,36
0,48
0,60
0,72
0,84
0,96
1,08
1,20
2
0,24
0,48
0,72
0,96
1,20
1,44
1,68
1,92
2,16
2,40
3
0,36
0,72
1,08
1,44
1,80
2,16
2,52
2,88
3,24
3,60
4
0,48
0,96
1,44
1,92
2,40
2,88
3,36
3,84
4,32
4,80
5
0,60
1,20
1,80
2,40
3,00
3,60
4,20
4,80
5,40
6,00
6
0,72
1,44
2,16
2,88
3,60
4,32
5,04
5,76
6,48
7,20
7
0,84
1,68
2,52
3,36
4,20
5,04
5,88
6,72
7,56
8,40
8
0,96
1,92
2,88
3,84
4,80
5,76
6,72
7,68
8,64
9,60
9
1,08
2,16
3,24
4,32
5,40
6,48
7,56
8,64
9,72
10,80
10
1,20
2,40
3,60
4,80
6,00
7,20
8,40
9,60
10,80
12,00
12
1,44
2,88
4,32
5,76
7,20
8,64
10,08
11,52
12,96
14,40
14
1,68
3,36
5,04
6,72
8,40
10,08
11,76
13,44
15,12
16,80
16
1,92
3,84
5,76
7,68
9,60
11,52
13,44
15,36
17,28
19,20
18
2,16
4,32
6,48
8,64
10,80
12,96
15,12
17,28
19,44
21,60
20
2,40
4,80
7,20
9,60
12,00
14,40
16,80
19,20
21,60
24,00
- 79 -
KAN-therm Steel System - technical information
21
KAN-therm Steel System - "L", "Z", and "U" compensator selection Table 5. Required expansion compensation length A [mm] for KAN-therm Steel Pipe external diameters dz [mm]
Elongation values ΔL [mm]
15
2
400
400
400
337
400
412
4
400
400
422
476
532
583
6
427
468
517
583
652
714
18
22
28
35
42
54
76,1
88,9
108
468
555
600
661
661
785
849
935
810
962
1039
1146
Required expansion compensation length A [mm]
8
493
540
597
673
753
825
935
1110
1200
1323
10
551
604
667
753
842
922
1046
1241
1342
1479
12
604
661
731
825
922
1010
1146
1360
1470
1620
14
652
714
790
891
996
1091
1237
1469
1588
1750
16
697
764
844
952
1065
1167
1323
1570
1697
1871
18
739
810
895
1010
1129
1237
1403
1665
1800
1984
20
779
854
944
1065
1191
1304
1479
1756
1897
2091
22
817
895
990
1117
1249
1368
1551
1841
1990
2193
24
854
935
1034
1167
1304
1429
1620
1923
2079
2291
26
889
973
1076
1214
1357
1487
1686
2002
2163
2385
28
922
1010
1117
1260
1409
1543
1750
2077
2245
2475
30
955
1046
1156
1304
1458
1597
1811
2150
2324
2561
32
986
1080
1194
1347
1506
1650
1871
2221
2400
2645
34
1016
1113
1231
1388
1552
1700
1928
2289
2474
2727
Table 5 presents required expansion compensation length A for different thermal elongation values ΔL and pipe external diameters (dz). Rules for selection of different types of compensators are given below. "L" type compensator
A − expansion compensation length; FP − fixed point (prevents the pipeline from moving); L
− pipeline initial length;
ΔL − pipeline thermal elongation.
For compensation arm A dimensioning, a substitute length Lz = L is taken, and for Lz length the thermal elongation value ΔL is determined from Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. "Z" type compensator
A − expansion compensation length; FP − fixed point (prevents the pipeline from moving); L
− pipeline initial length;
ΔL − pipeline thermal elongation.
For compensation arm A dimensioning, L1 and L2 sum is taken as a substitute length Lz = L1+L2, and for Lz length a substitute DL is determined on the basis of Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. - 80 -
KAN-therm Steel System - technical information
21
"U" type compensator
A − expansion compensation length; FP − fixed point (prevents the pipeline from moving); L
− pipeline initial length;
ΔL − pipeline thermal elongation. W − U type compensator width
If a fixed point is placed within compensator width W, then for compensation arm A dimensioning, L1 and L2 bigger value is taken as a substitute length Lz = max (L1, L2), and for Lz length a substitute ΔL is determined on the basis of Tab. 4. Next, the expansion compensation length A is determined on the basis of Tab. 5. Compensator width W = A/2.
KAN-therm Steel System - pressure drops Coefficient of local pressure drops ζ for fluid flow through fittings are presented in Table 6. Tab. 6. Coefficient of local pressure drops ζ for fittings
∅15 - 54 mm Analytical direct method ζ
1,5 m
0,7 m
0,5 m
0,5 m
0,4 m
0,9 m
1,3 m
1,5 m
3,0 m
Method of equivalent length 15
0,90
0,40
0,30
0,30
0,25
0,50
0,70
0,90
1,80
18
1,10
0,50
0,40
0,40
0,30
0,65
0,90
1,10
2,30
22
1,40
0,60
0,50
0,50
0,40
0,80
1,20
1,40
2,80
28
1,90
0,90
0,60
0,60
0,50
1,10
1,50
1,90
3,80
35
2,50
1,20
0,80
0,80
0,70
1,50
2,10
2,50
5,00
42
3,10
1,40
1,00
1,00
0,90
1,80
2,60
3,10
6,20
54
4,00
1,80
1,30
1,30
1,10
2,30
3,30
4,00
8,00
1,0 m
1,3 m
1,5 m
3,0 m
∅76,1 - 88,9 - 108 mm Analytical direct method ζ
1,3 m
0,6 m
0,4 m
0,5 m
0,1 m
Method of equivalent length 76,1
6,10
2,80
1,90
2,40
0,50
4,70
6,10
7,10
14,20
88,9
7,80
3,60
2,40
3,00
0,60
6,00
7,80
9,00
18,00
108
10,60
4,90
3,30
4,10
0,80
8,20
10,60
12,30
24,60
Tables 7 and 8 present linear pressure drops R [Pa/m] caused by pipe wall friction, in function of flow rate Q [l/s] and flow velocity [m/s] at temperatures of 20°C (Tab. 7) and 60°C (Tab. 8). Table 9 presents linear pressure drops R [Pa/m] for water at a temperature of 80°C power Q at a temperature drop Δt 20°C, or in a function of water flow mi [kg/s].
- 81 -
KAN-therm Steel System - technical information Table 7. Linear pressure drops R for water at a temperature of 20째C
- 82 -
21
21
KAN-therm Steel System - technical information
Table 8. Linear pressure drops R for water at a temperature of 60째C
- 83 -
KAN-therm Steel System - technical information
21
Table 9. Linear pressure drops R for water at a temperature of 80°C in a function of power Q transported at a temperature drop Δt 20°C or in a function of water flow mi
- 84 -
KAN-therm Steel System
22
KAN-therm press carbon steel tube, zinc coated Size 15×1,2 18×1,2 22×1,5 28×1,5 35×1,5 42×1,5 54×1,5 76,1×2 88,9×2 108×2
Pcs./packing bar 6m bar 6m bar 6m bar 6m bar 6m bar 6m bar 6m bar 6m bar 6m bar 6m
Code 620460.5 620461.6 620462.7 620463.8 620464.9 620465.1 620466.0 620480.3 620481.4 620482.5
Price €/m
Pcs./packing 10/200 10/200 10/160 10/100 10/100 10/60 10/40 4/24 4/12
Code Price €/pcs. 620227.3 620228.4 620229.5 620230.6 620231.7 620232.8 620233.9 620234.1 620235.0
Pcs./packing 2/50 2/40 2/30 2/20 2/16 2/10
Code Price €/pcs. 620719.0 620720.1 620721.2 620722.3 620723.4 620724.5
KAN-therm press male connector Size 15×R⅜ 15×R½ 18×R½ 18×R¾ 22×R¾ 28×R1 35×R1¼ 42×R1½ 54×R2
l 35 39 39 40 44 48 55 59 69
z 15 19 19 20 23 25 29 29 34
KAN-therm press male union connector Size 15×R½ 22×R¾ 28×R1 35×R1¼ 42×R1½ 54×R2
l 63,8 70 74,7 81,8 88 100
z 43,8 49 51,7 55,8 58 65
KAN-therm press male union connector (for VK radiators) Size 15×G¾ 18×G¾
l 38 38
z 18 18
Pcs./packing 10/100 10/100
Code Price €/pcs. 620816.9 620817.1
Pcs./packing 10/130 10/120 10/80 10/100 10/60 10/60
Code Price €/pcs. 620237.2 620238.3 620239.4 620240.5 620780.6 620241.6
Pcs./packing 10/200 10/160 10/100 10/70 10/100
Code Price €/pcs. 620243.8 620244.9 620245.1 620246.0 620247.1
Pcs./packing 10/140 10/140 10/80 10/60 10/40 4/24 4/16 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620136.0 620137.1 620138.2 620139.3 620140.4 620141.5 620142.6 6206200 620620.0 6206211 620621.1 6206222 620622.2
KAN-therm press female connector Size 15×Rp½ 18×Rp½ 18×Rp¾ 22×Rp¾ 28×Rp½ 28×Rp1
l 41 40 43 43 38 49
z 6 5 6,7 5,7 2 7
KAN-therm press nipple female connector Size 15×Rp½ 18×Rp½ 18×Rp¾ 22×Rp½ 22×Rp¾
a 51 50 53 50 53
z 36 35 36,7 35 36,7
d 15 18 18 22 22
KAN-therm press coupling Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
l 53 53 55 59 65 76 86 140 142 160 165 192 195
z 13 13 13 13 13 16 16 30 38 34 45 38 44
size and directions in [mm] *available after stock-out of the elements in last-performance
catalog net prices - no discount
- 85 -
KAN-therm Steel System
22
KAN-therm press long coupling Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
l 80 80 84 91 102 120 140 230 230 262 260 305 310
z 25 25 25 30 30 40 40 60 60 70 70 80 80
Pcs./packing 10/60 10/60 10/60 10/40 10/20 4/16 4/8 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620144.8 620145.9 620146.1 620147.0 620148.1 620149.2 620150.3 6206233 620623.3 6206244 620624.4 6206255 620625.5
Pcs./packing 10/150 10/90 10/60 10/30 10/10 2/16 2/8 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620155.8 620156.9 620157.1 620158.0 620159.1 620160.2 620161.3 6208004 620626.6 6208048 620627.7 6208059 620628.8
Pcs./packing 10/120 10/80 10/60 10/30 10/10 2/8 2/6 4/0 2/0 4/0 4/0 4/0 4/0
Code Price €/pcs. 620163.5 620164.6 620165.7 620166.8 620167.9 620168.1 620169.0 6208061 620629.9 6208070 620630.1 6208081 620631.0
Pcs./packing 10/150 10/120 10/70 10/40 5/25 2/16 2/8 4/0 4/0 4/0 4/0 2/0 2/0
Code Price €/pcs. 620170.1 620171.2 620172.3 620173.4 620174.5 620175.6 620176.7 6208125 620632.1 6208136 620633.2 6208147 620634.3
Pcs./packing 10/150 10/120 10/60 10/40 5/25 4/16 2/8 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620177.8 620178.9 620179.1 620180.0 620181.1 620182.2 620183.3 6208092 620635.4 6208103 620636.5 6208114 620637.6
KAN-therm press 90° elbow Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
l 41 45 51 60 71 86 105 151 152 173 175 214 213
z 21 25 30 37 45 56 70 96 99,5 110 115 137 139
KAN-therm press nipple 90° elbow Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
l 41 45 51 60 71 86 105 151 152 173 175 214 213
z 21 25 30 37 45 56 70 96 99,5 110 115 137 139
h 48,6 51,4 58,1 65,5 75,9 92,5 110,6 167 167 188 194 235 235
KAN-therm press 45° elbow Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
l 30,5 32,1 35,2 40,1 46,4 56,1 66,9 96 99 109 113 140 139
z 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41 46,5 46 53 63 65
KAN-therm press nipple 45° elbow Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54 *76,1×76,1 76,1×76,1 *88,9×88,9 88,9×88,9 *108×108 108×108
- 86 -
l 30,5 32,1 35,2 40,1 46,4 56,1 66,9 96 99 109 113 139 139
z 10,5 12,1 14,2 17,1 20,4 26,1 31,9 41 46,5 46 53 63 65
h 38,1 38,5 42,3 45,6 51,3 62,6 72,5 117 115 128 130 161 160
size and directions in [mm] *available after stock-out of the elements in last-performance
catalog net prices - no discount
KAN-therm Steel System
22
KAN-therm press tee Size 15×15×15 18×18×18 22×22×22 28×28×28 35×35×35 42×42×42 54×54×54 *76,1×76,1×76,1 76,1×76,1×76,1 *88,9×88,9×88,9 88,9×88,9×88,9 *108×108×108 108×108×108
l1 35 36,5 39,5 44,5 51 60 71 115 115 131 130,5 152 155
z1 15 16,5 18,5 21,5 25 30 36 60 63 68 70 75 79
l2 44 45,5 48,5 53,5 60 66,5 77,5 121 120 126 128 152 153
z2 24 25,5 27,5 30,5 34 36,5 42,5 66 68 63 68 76 77
Pcs./packing 10/80 10/70 10/40 10/30 5/15 4/8 2/6 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620249.3 620250.4 620251.5 620252.6 620253.7 620254.8 620255.9 6206442 620644.2 6206453 620645.3 6206464 620646.4
z2 24 26,5 25,5 26 27,5 27,5 29 30,5 30,5 30,5 34 34 34 34 36,5 36,5 36,5 42,5 42,5 42,5 42,5 46 85 62 70 72 93
Pcs./packing 10/80 10/60 10/70 10/70 10/50 10/50 10/40 10/30 10/30 10/30 10/20 10/20 5/20 10/20 4/12 4/12 4/12 2/8 2/8 2/8 2/8 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620277.9 620278.1 620258.1 620279.0 620260.3 620261.4 620280.1 620262.5 620263.6 620264.7 620265.8 620266.9 620267.1 620268.0 620269.1 620270.2 620271.3 620272.4 620273.5 620274.6 620275.7 6206475 620647.5 6206486 620648.6 6206497 620649.7
Pcs./packing 5/50 5/50 10/30 10/30 10/30 10/30 10/20
Code Price €/pcs. 620288.9 620289.1 620290.0 620291.1 620713.5 620714.6 620715.7
Pcs./packing 10/200 10/140 10/120 10/70 10/100 10/80 10/50 10/60 4/24 5/30 4/24 4/16 4/16 10/30 4/16 2/0 2/0 2/0 2/0 2/0 2/0 2/0 2/0 2/0 2/0 2/0 2/0
Code Price €/pcs. 620213.0 620215.2 620216.3 620217.4 620218.5 620219.6 620220.7 620221.8 620665.1 620666.2 620222.9 620223.1 620224.0 620668.4 620225.1 6206387 620638.7 6206398 620639.8 6206409 620640.9 6206411 620641.1 6206420 620642.0 6206431 620643.1
KAN-therm press reducing tee Size 15×18×15 15×22×15 18×15×18 18×22×18 22×15×22 22×18×22 22×28×22 28×15×28 28×18×28 28×22×28 35×15×35 35×18×35 35×22×35 35×28×35 42×22×42 42×28×42 42×35×42 54×22×54 54×28×54 54×35×54 54×42×54 *76,1×54×76,1 76,1×54×76,1 *88,9×76,1×88,9 88,9×76,1×88,9 *108×88,9×108 108×88,9×108
l1 35 35 36,5 36,5 39,5 39,5 39,5 44,5 44,5 44,5 51 51 51 51 60 60 60 71 71 71 71 115 115 131 130 152 155
z1 15 15 16,5 16,5 18,5 18,5 18,5 21,5 21,5 21,5 25 25 25 25 30 30 30 36 36 36 36 60 53 68 60 75 76
l2 44 47,5 45,5 47 47,5 47,5 52 50,5 50,5 51,5 54 54 55 57 57,5 59,5 62,5 63,5 65,5 68,5 72,5 84 120 117 120 135 153
KAN-therm press pipe crosss Size 15×15×15×15 18×15×18×15 22×15×22×15 22×18×22×18 28×15×28×15 28×18×28×18 28×22×28×22
l1 35 36,5 39,5 39,5 44,5 44,5 44,5
z1 15 16,5 18,5 18,5 21,5 21,5 21,5
l2 35 35 35 36,5 35 36,5 39,5
z2 15 15 15 16,5 15 16,5 18,5
h 21 22,5 24,5 26 27,5 29 31
KAN-therm press nipple reducer Size 18×15 22×15 22×18 28×15 28×18 28×22 35×22 35×28 42×22 42×28 42×35 54×22 54×28 54×35 54×42 *76,1×42 76,1×42 *76,1×54 76,1×54 *88,9×54 88,9×54 *88,9×76,1 88,9×76,1 *108×76,1 108×76,1 *108×88,9 108×88,9
l 52 58,4 59 64 62,3 63 68 69 80 79 76 89 87 89 91 151 153 145 147 157 163 157 160 196 184 192 204
z 32 38,4 39 44 42,3 42 47 46 59 56 50 68 64 63 61 121 124 110 112 122 128 102 108 141 132 129 144
d1 18 22 22 28 28 28 35 35 42 42 42 54 54 54 54 76,1 76,1 76,1 76,1 88,9 88,9 88,9 88,9 108 108 108 108
d2 15 15 18 15 18 22 22 28 22 28 35 22 28 35 42 42 42 54 54 54 54 76,1 76,1 76,1 76,1 88,9 88,9
size and directions in [mm] *available after stock-out of the elements in last-performance
catalog net prices - no discount
- 87 -
KAN-therm Steel System
22
KAN-therm press male elbow 90° Size 15×R⅜ 15×R½ 18×R½ 22×R¾ 28×R1 35×R1¼ 42×R1½ 54×R2
l2 44,5 49,5 54 61,5 73,5 85,5 95,5 115,5
z 21 21 25 30 37 45 56 70
l1 41 41 45 51 60 71 86 105
Pcs./packing 10/150 10/150 10/100 10/60 10/30 10/10 4/12 2/8
Code Price €/pcs. 620198.7 620199.8 620200.9 620201.1 620202.0 620203.1 620204.2 620205.3
Pcs./packing 10/100 10/100 10/100 10/60
Code Price €/pcs. 620207.5 620208.6 620209.7 620210.8
Pcs./packing 10/80 10/50 10/50 10/30 10/30 10/20 10/20 4/16 4/16 2/8 2/8 2/0 2/0 1/0 1/0 1/0 1/0
Code Price €/pcs. 620281.2 620282.3 620283.4 620284.5 620718.1 620285.6 620710.2 620286.7 620711.3 620287.8 620712.4 6206508 620650.8 6206519 620651.9 6206521 620652.1
Pcs./packing 10/80 10/60 10/50 10/20
Code Price €/pcs. 620193.2 620194.3 620195.4 620196.5
Pcs./packing 10/80 10/60 10/40 10/20 4/8 2/4 2/2
Code Price €/pcs. 620185.5 620186.6 620187.7 620188.8 620189.9 620190.1 620191.0
KAN-therm press short male elbow 90° Size 15×R⅜ 15×R½ 18×R½ 22×R¾
l2 40 41 41,5 44,5
z 20 21 21,5 23,5
l1 22 28 28 32
KAN-therm press female tee Size 15×Rp½×15 18×Rp½×18 22×Rp½×22 28×Rp½×28 28×Rp¾×28 35×Rp½×35 35×Rp¾×35 42×Rp½×42 42×Rp¾×42 54×Rp½×54 54×Rp¾×54 *76,1×Rp¾×76,1 76,1×Rp¾×76,1 *88,9×Rp¾×88,9 88,9×Rp¾×88,9 *108×Rp¾×108 108×Rp¾×108
l1 35 36,5 39,5 44,5 44,5 51 51 60 60 71 71 115 121 131 127,5 152 155
z1 15 16,5 18,5 21,5 21,5 25 25 30 30 36 36 60 66 68 63,5 75 77
l2 36,5 37 39 42 44 45,5 47,5 48 50 54 56 70 69 76 76 86 85
z2 21,5 22 24 27 27,7 30,5 31,2 33 33,7 39 39,7 54 52,7 59 59,7 70 68,7
KAN-therm crossover Size 15×15 18×18 22×22 28×28
l 54 59,5 64,5 75
a 155 167 177 215
b 31 34 37 43
KAN-therm bend 90° Size 15×15 18×18 22×22 28×28 35×35 42×42 54×54
- 88 -
h1 70 70 72 82 120 150 200
h1min 58 63 70 80 100 120 145
h2 120 120 120 120 200 250 300
h2min 58 63 70 80 100 120 145
size and directions in [mm] *available after stock-out of the elements in last-performance
catalog net prices - no discount
KAN-therm Steel System
22
KAN-therm press cup Size 15 18 22 28 35 42 54 76,1 88,9 108
l 25,5 26,3 28,5 32,3 34,4 43,2 51,8 71 82 98
z 5,5 6,3 7,5 9,3 8,4 13,2 16,8 16 19 21
Pcs./packing 20/80 20/300 10/240 10/130 5/75 4/48 4/32 4/0 4/0 4/0
Code Price €/pcs. 620295.5 620296.6 620297.7 620298.8 620299.9 620300.1 620301.0 6206915 6206926 6206937
z 65 72 97
Pcs./packing 2/0 4/0 4/0
Code Price €/pcs. 620656.3 620657.4 620658.5
Pcs./packing 4/0 2/0 2/0
Code Price €/pcs. 620659.6 620660.7 620661.8
Pcs./packing 20/600 20/500 20/500 20/400 20/400 20/300 20/300
Code 6222216 6222227 6222238 6222249 6222251 6222260 6222271
Price €/pcs.
Pcs./packing 20/600 20/500 20/500 20/400 20/400 20/300 20/300
Code 6119401 6119410 6119421 6119432 6119443 6119454 6119465
Price €/pcs.
Pcs./packing 20/600 20/500 20/500 20/400 20/400 20/300 20/300 5/100 5/100 5/50
Code Price €/pcs. 611591.2 611592.3 611593.4 611594.5 611595.6 611596.7 611597.8 620801.5 620802.6 620803.7
Pcs./packing 20/600 20/500 20/500 20/400 20/400 20/300 20/300 5/100 5/100 5/50
Code Price €/pcs. 480521.8 480522.9 480523.1 480524.0 480525.1 480526.2 480527.3 611937.7 611938.8 611939.9
KAN-therm press plug Size 76,1 88,9 108
l 87 96 125
KAN-therm press flange Size 76,1 88,9 108
z 74 83 92
d 185 200 220
d2 18 18 18
h 126 143 168
k 145 160 180
b 18 20 20
holes 4 8 8
KAN-therm LBP EPDM O-Ring Size 15 18 22 28 35 42 54
KAN-therm LBP FPM Viton O-Ring Size 15 18 22 28 35 42 54
KAN-therm EPDM O-Ring Size *15 *18 *22 *28 *35 *42 *54 76,1 88,9 108
KAN-therm FPM Viton O-Ring Size *15 *18 *22 *28 *35 *42 *54 76,1 88,9 108 size and directions in [mm] *available after stock-out of the elements in last-performance
catalog net prices - no discount
- 89 -