Foreword
This Repair Manual is designed to facilitate competent repair of the engines listed herein. The pictures and relevant descriptions show typical work that may not always be applicable to the engine in hand, which nevertheless does not mean that they are not correct. In such cases the repair work is to be planned and carried out in a similar way. It is compulsory that the engine be removed before performing any of the work describe in this Repair Manual. The expert knowledge necessary for handling diesel engines was taken for granted when this publication was compiled. Note: Only use fuel, coolants and lubricants in accordance with MAN’s regulations otherwise the manufacturer’s warranty will not apply! For basic information on the fuels see the publication “Fuels, Lubricants and Coolants for MAN Industrial Gas Engines”. You can find the approved products in the internet under: http://www.man-mn.com/ " Products & Solutions " E-Business Repairs to drive units are to be performed by our customer service or the customer service of the manufacturer.
Best regards MAN Nutzfahrzeuge Aktiengesellschaft Nuremberg Plant
Since our products are in continuous development, we reserve the right to make technical modifications. © 2005 MAN Nutzfahrzeuge Aktiengesellschaft Reprinting, copying or translation, even of extracts, is not allowed without written permission from MAN. All rights under the copyright law are strictly reserved by MAN. MTDB
Technical status: 02.2005
1
51.99598−8154
Instructions
Important instructions which concern technical safety and protection of persons are emphasised as shown below. Danger: This refers to working and operating procedures which must be complied with in order to rule out the risk to persons. Caution: This refers to working and operating procedures which must be complied with in order to prevent damage to or destruction of material. Note: Explanatory descriptions which help in understanding the relevant work or operating procedure to be carried out.
Assembly of pipes Danger: No pipes may be bent. Risk of breakage!
Fitting flat seals / gaskets Flat seals / gaskets are often inserted with sealing agents or adhesives to make fitting them easier or to achieve better sealing. Flat seals may slip in operation due to the “sewing-machine� effect, in particular if they are used between parts with different rates of linear expansion under heat (e.g. aluminium and cast iron), and leaks may then occur. Example: The cap of the front crankshaft seal. If a sealing agent or an adhesive is used here the flat seal will move inwards in the course of time as a result of the different expansion rates of the materials. Oil will be lost, for which the shaft seal may be thought to be responsible.
Flat seals / gaskets can be fitted properly only if the following points are observed: D Use only genuine MAN seals / gaskets. D The sealing faces must be undamaged and clean. D Do not use any sealing agent or adhesive − as an aid to fitting the seals a little grease can be used if necessary so that the seal will stick to the part to be fitted. D Tighten bolts evenly to the specified torque.
Fitting round sealing rings D Use only genuine MAN round sealing rings. D The sealing faces must be undamaged and clean. D Always wet round sealing rings with engine oil before fitting them.
2
Contents Page Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine type classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fault table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General notes on engine overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schematic diagram of engine lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schematic diagram of cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schematic diagram of engine timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 2 5 6 10 13 14 16 17 19
Ignition Replacing the spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 21
Cooling system Draining and filling coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and refitting coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 25
Lubrication Changing oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and refitting oil pan, Removing and refitting oil intake line . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and refitting oil pump, disassembly and re-assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing oil injection nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 27 28 29 32
Flywheel / Crankshaft seal Replacing front crankshaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing, repairing flywheel − Replacing starter ring gear . . . . . . . . . . . . . . . . . . . . . . Removing and installing crankshaft seal, flywheel end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing flywheel housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33 34 36 37
Intake / exhaust system Removing and installing intake pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing exhaust pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39 40
Cylinder head Removing and installing rocker arm mechanism, removing and installing cylinder head . . . . . . . . . . Setting valve clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembling and assembling rocker arm mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking compression pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41 45 46 48 52
Valve timing Removing and installing timing case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing camshaft bearing bushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking valve timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53 58 60 66
3
Contents Page Crankgear, pistons Removing and installing crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing piston with conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing piston from conrod and installing, checking − replacing conrod . . . . . . . . . . . . . . . . . . . . . Removing and installing, replacing piston rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing cylinder liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Measuring excess piston retrusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67 70 73 75 77 78
Attachments Removing and installing starter motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
Service Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine E 0834 E 302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine E 0836 E 302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cylinder liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flywheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conrod bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Piston ring grooves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Piston rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valve springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valve train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valve tappets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil pump gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacities of oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starter motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Torque guide values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cylinder head bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81 83 83 84 85 85 86 87 88 89 89 90 90 90 91 92 92 93 93 93 96 96 96 97 97 98 99 101
Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
111
4
Engine type classification
The type designation, consisting of a sequence of letters and numbers, indicates some characteristics of each engine, provided you are familiar with the basic terminology.
The system is explained here using the type E 0836 E 302 as an example: E
The “E” at the start of the type designation stands for natural gas (German: Erdgas)
08
The numbers “08” indicate that this is a power unit with 108 mm bore
3
The “3” means 125 mm stroke
6
The “6” indicates the number of cylinders 6
E
The “E” stands for “fitted engine” (German: Einbaumotor) and is intended to distinguish MAN vehicle engines
302
This is a factory-internal development number
5
Safety regulations
General Important safety regulations are summarized in this quick-reference overview and arranged by topic to effectively convey the knowledge necessary to avoid accidents causing injury, damage or environmental hazard. Additional information can be found in the operating instructions of the engine. Important: Should an accident occur despite all precautionary measures, particularly one involving contact with corrosive acid, penetration of fuel under the skin, scalding by hot oil, antifreeze splashing into the eyes etc. you must seek medical assistance immediately.
1. Regulations for the prevention of accidents with personal injury Inspection, adjustment and repair work may only be performed by authorised and skilled personnel. D The engine may only be started and operated by authorised personnel. D When the engine is running, do not get too close to the rotating parts. Wear close-fitting clothing.
D Do not touch hot engine with bare hands: Risk of burns.
ËË D Keep area surrounding engine, ladders and stairways free of oil and grease. Accidents caused by slipping can have serious consequences. D Only work with tools which are in good condition. Worn spanners / wrenches slip: Danger of injury. D Persons must not stand under an engine suspended on a crane hook. Keep lifting gear in order.
D Open the coolant circuit only when the engine has cooled down. If it is unavoidable that the circuit be opened with the engine at operating temperature, observe the instructions in the chapter “Maintenance and care” in the operating instructions. D Do not tighten or undo pipes and hoses under pressure (lubricating oil circuit, coolant circuit and any downstream hydraulic oil circuits). The fluids which flow out can cause injury. D When working on the electrical system, first disconnect the earth cable of the battery and reconnect this last to prevent short circuits.
6
Safety regulations
D Follow the manufacturer’s instructions for handling batteries. Caution: Accumulator acid is toxic and caustic. Battery gases are explosive. D When performing welding work, observe the “Notes for welders”.
2. Regulations for the prevention of engine damage and premature wear D The engine must be cleaned thoroughly prior to repair. Ensure that during repair work no dirt, sand or foreign bodies enter the engine. D If engine operation is disrupted, immediately determine the cause and have it remedied to prevent additional damage. D In every case, use only original MAN spare parts. The installation of parts that are “just as good” but do not originate from MAN can under certain circumstances cause severe damage − for which the workshop performing the repair must bear responsibility. D Never allow the engine to run dry, i.e. without lubricant or coolant. Appropriate notices must be attached to engines that are not ready for operation. D Only use lubricants, fluids and fuel approved by MAN (gas, engine oil, antifreeze and corrosion protection agents). Pay attention to cleanliness. D Do not fill engine oil beyond the max. notch on the dipstick. Do not exceed the maximum permissible tilt of the engine. Serious damage to the engine may result if these instructions are not adhered to. D Control and monitoring devices (charge control, oil pressure, coolant temperature) must be in perfect working order.
3. Safety instructions for handling the ignition system
D When the engine is in operation, the following parts of the ignition system must not be touched or disconnected under any circumstances: − Ignition coils and caps − Cables of the high-voltage circuit − Cables of the low-voltage circuit − Plugs of the output and input wiring harness D For all work related to set-up, operation, conversion, customisation, maintenance and repairs, the power must be disconnected from the ignition system and secured against inadvertent reactivation.
7
Safety regulations
4. Regulations for the prevention of environmental damage Engine oil and filter cartridges D Old oil must be passed on for recycling. D Take extreme care that no oil enters the waste water system or seeps into the ground. Caution: The drinking water supply could be contaminated. D Filter elements are classed as dangerous waste and must be treated as such. Coolant D Treat undiluted corrosion protection agents and / or antifreeze as hazardous waste. D When disposing of used coolant, the regulations issued by the relevant local authorities must be observed.
5. Instructions for handling used engine oil ∗ Prolonged or repeated contact between the skin and any kind of engine oil decreases the skin. Drying, irritation or inflammation of the skin may therefore occur. Used engine oil also contains hazardous substances that have caused skin cancer in tests on animals. If the basic principles of work safety and hygiene are observed, handling used engine oil does not represent a health hazard. Precautionary measures to protect your health: D Avoid prolonged or repeated skin contact with used engine oil. D Protect your skin by means of suitable agents (creams etc.) or wear protective gloves. D Clean skin which has been in contact with engine oil. − Wash thoroughly with soap and water. A nail brush provides effective assistance here. − Special hand cleaning agents make it easier to clean dirty hands. − Do not use petrol (gasoline), diesel fuel, gas oil or solvents as washing agents. D After washing apply a fatty skin cream to the skin. D Change clothing and shoes that are soaked in oil. D Do no put oily cloths in you pockets. Ensure that used engine oil is disposed of in the appropriate manner. − Engine oil is a substance that endangers the water supply − For this reason do not let engine oil get into the ground, waterways, the drains or the sewers. Violations are punishable. Carefully collect and dispose of used engine oil. Information on collection points can be obtained from sales personnel, the supplier or the local authorities. ∗ Based on “Information sheet for handling used engine oil”.
8
Safety regulations
6. Safety instructions for handling gaseous fuels Gaseous fuels consist essentially of methane, propane and butane as well as traces of higher hydrocarbons and inert components such as carbon dioxide and nitrogen. D The regulations applicable to gas installations must be observed.
D Exhaust gases are toxic. Comply with the regulations for the installation of MAN industrial gas engines for operation in enclosed areas. Ensure adequate ventilation. D Smoking and naked flames are prohibited.
D Leaks in the gas supply system mean danger of explosion and these must be remedied immediately.
D Fire extinguishers and other firefighting equipment must be on hand. D Do not store combustible material in the engine room. Conduct in the case of gas leaks D D D D
Close the shutoff valve of the gas supply. Switch off the main switch of the electric system. Cordon off the danger zone. Ask persons who are not involved in the work to leave the danger zone. If gas is leaking, inform the relevant authorities immediately and initiate repairs.
Conduct in the event of fire D Alert the fire brigade. D Immediately assist any injured persons, call paramedics if necessary. D In the case of a pure gas fire, do not extinguish the gas flame; if necessary, cool down the burning object (e.g. by starving the fire of oxygen: close doors and windows). Burning gas = controlled gas! D Prevent the flames from spreading. D If the flames spread to the surroundings, use a fire extinguisher. D Stay calm!
9
Fault table
Operating faults and possible causes We recommend A repair is only complete when both the damage that occurred and the possible causes have been eliminated. Finding out the cause of damage is often more difficult than repairing the damage that occurred. We therefore recommend that you obtain a precise description of the operating fault before removing and dismantling components. Then use a process elimination (questions) to pin-point the probable causes and investigate and eliminate these successively on the basis of the table and your own experience. This helps to reduce repairs to the required scale and to counteract claims regarding “over-eager” replacement of parts and complaints about expensive work and down time.
Note: The following list is conceived as an aid to memory for experts so that to causes of damage are overlooked when dealing with faults. It is expected of experts that they are very familiar with the repair instructions for the engine, but also with the engine operating instructions and “Fuels, Lubricants and Coolants for MAN Industrial Gas Engines”.
10
Fault table
1. 2.
x
Starter motor does not turn engine or only slowly (solenoid switch energises “click” is audible) Starter motor turns, engine does not turn 3. Starter motor turns engine, engine does not start / starts poorly 4. Ignition failure 5. Irregular engine running 6. Engine stalls during operation, no longer starts 7. Engine “shakes” 8. Engine only runs at idle speed 9. Idle speed unstable 10. Engine does not reach its nominal speed 11. Engine does not reach its nominal power 12. Fuel consumption too high 13. Oil consumption too high 14. Engine too “loud” / mechanical noise 15. Heavy blue smoke formation 16. Heavy white smoke formation 17. Exhaust temperature / exhaust back pressure too high (thermal overload) 18. Lubrication oil pressure too low 19. Temperature difference engine exit / engine entry too great 20. Coolant temperature too high Possible causes Batteries discharged, battery cable connections loose or corroded, power circuit interrupted
x x x x
x x x x x x x x x o
x x x o
x x x
x
x x x x x
x
Throttle valve not in full-load position / actuating rod jammed / throttle valve incorrectly adjusted
x x x x x x x x x
x x
x
x x
x x
x x
x x
x
x x x x x x x x x x x x x x x x x x x
x x x x x x
x = o =
Starter motor defective (carbon brushes loosened / worn, coil damaged, ground fault) Engaging lever / bearing bolt of the engaging lever broken Crankshaft drive blocked Engine oil viscosity unsuitable, not suited to ambient temperature Ignition control unit defective Impulse sensor defective / gap incorrectly set Spark plug defective Ignition cable defective Ignition coil defective Ignition point incorrectly set Throttle valve does not open / actuating rod jammed / setting unit de-energized or defective
Shut-off solenoid valve of gas supply closed / does not open Zero pressure regulator of gas supply not correctly set or defective Gas metering valve defective Gas / air mixture too rich or too lean Lack of compression, or more than 3 bar pressure difference between the individual cylinders Valve clearance not correct Valve guides heavily worn Valve seats leaking Piston rings heavily worn, broken (overpressure in the crankcase) Air filter heavily soiled Charge mixture cooler soiled / leaking Charge mixture piping leaking Turbine and compressor wheel in the turbocharger soiled (running off balance) Coolant entering combustion chamber (cylinder head gasket leaking) Engine in cold running phase Crankcase breather blocked Oil level in oil pan too high Safety valve in the oil circuit defective (does not close, spring fatigued or broken) Heavy bearing wear Oil pump heavily worn Safety valve in the oil circuit defective (does not open), oil lines / oil ducts blocked Unsuitable exhaust-gas piping, heat exchanger and catalytic converters with excessive resistance
likely to apply might apply
11
Fault table
1. 2.
x = o =
Starter motor does not turn engine or only slowly (solenoid switch energises “click” is audible) Starter motor turns, engine does not turn 3. Starter motor turns engine, engine does not start / starts poorly 4. Ignition failure 5. Irregular engine running 6. Engine stalls during operation, no longer starts 7. Engine “shakes” 8. Engine only runs at idle speed 9. Idle speed unstable 10. Engine does not reach its nominal speed 11. Engine does not reach its nominal power 12. Fuel consumption too high 13. Oil consumption too high 14. Engine too “loud” / mechanical noise 15. Heavy blue smoke formation 16. Heavy white smoke formation 17. Exhaust temperature / exhaust back pressure too high (thermal overload) 18. Lubrication oil pressure too low 19. Temperature difference engine exit / engine entry too great 20. Coolant temperature too high Possible causes x Flow resistance of cooling system too great x x Soiling of cooling system x Coolant level too low, air in the coolant circuit x Coolant pump configured too small x x Coolant lines leaking, blocked or twisted x Engine mounting unsuitable / worn
likely to apply might apply
12
General notes on engine overhaul
The service life of an engine is influenced by very different factors. It is therefore not possible to specify certain fixed numbers of operating hours for general overhauls. In our view, it is not necessary to open up an engine or perform a general overhaul as long as the engine has good compression values and the following operating values have not changed significantly in relation to the values measured on commissioning the engine: D Exhaust temperature D Coolant and lubricant temperature D Oil pressure and oil consumption
The following criteria greatly influence the length of the engine service life: D Correct power setting in accordance with conditions of use D Technically correct installation D Inspection if installation by authorised personnel D Regular maintenance as per maintenance plan D Selection and quality of lubricants, fuel and coolant according to publication “Fuels, Lubricants and Coolants for MAN Industrial Gas Engines�
13
Engine views
Engine views E 0834 E 302 1 7 2
6
3
4 5
8
12
9
11
10
14
Engine views
À Crankcase breather Á Intake pipe  Starter motor à Oil filter Ä Oil cooler Å Coolant inlet Æ Coolant vent connection to separate vent reservoir Ç Oil filler neck È Coolant outlet É Oil drain plug 11
Oil dipstick
12
Exhaust pipe
15
Schematic diagram of engine lubrication
1
2
3
4
5
9
8
7
À Intermediate timing gear
Å Main flow oil filter
Á Oil injection nozzle for piston cooling
Æ Oil cooler
 Main oil gallery
Ç Relief valve
à Switch for oil pressure warning lamp
È Oil gear pump
Ä Bypass valve for oil filter cartridge
16
6
Schematic diagram of cooling system
Cooling system with membrane expansion tank 6 5
7
4 3
8
2
9 1 10
À Engine Á Connection line to the intake side of the coolant pump ∅ 25 mm  Diaphragm expansion vessel (0.6 bar) à Plate with 5x10 mm bore Ä Vent reservoir
Å Automatic breather valve Æ Sensor for liquid level Ç Vent line ∅ 10 mm, throughflow quantity 7 to max. 10 l/min È Coolant inlet É Coolant outlet
D Pressure relief safety valve 3.5 bar Operating pressure: min. 0.6 bar max. 3.0 bar D Observe the filling regulations of the manufacturer of the cogeneration power unit D Coolant filling capacity, see “Service Data” D Fill up the cooling system with the filler device, keeping the breathers open until the coolant emerges bubble-free D Close breathers and increase pressure to a value which is approx. 0.2−0.4 bar above the pre-pressure of the expansion vessel D Start up system. Let it cool down after trail operation (i.e. after it reaches the operating temperature) D When the cooling temperature has fallen to below 50_C, increase the system pressure to 0.5 bar above the pre-pressure of the expansion vessel via the filler device
17
Thank you very much for your reading. Please Click Here Then Get More Information.