Connectors Overview n SMPTE Requirements
3G Transmission Design
Format
n 3G-SDI Popularity
Bit Rate Impedance (Zo)
HD-SDI SMPTE ST 292 1.485 Gb/s
3G-SDI SMPTE ST 424 2.97 Gb/s 75Ω 30 dB @ 1.5 GHz (@ 1.485 GHz) 15 dB 10 dB -
12G-SDI SMPTE ST 2082-1 11.88 Gb/s
3G-SDI (3Gb/s Signal/Data Serial Interface) is a transmission format (1080p) that provides twice the data transmission capacity (bandwidth) of today’s widely used HD-SDI (1080i), and its use has seen rapid expansion in recent years. The data format was standardized as SMPTE 424M in 2006, and was revised as the SMPTE ST 424 Standard in 2012, including a change in typical cable loss recommendations (from 20dB to 30dB). Dual-link 3G-SDI and Quad-link 3G-SDI provide reasonable solutions for meeting the production requirements of HDR HDTV, 2K/4K D-Cinema and UHDTV-1.
or to revise the circuit and/or equipment layout to compensate. It is also recommended that these calculations include a 2–3dB design margin.
n Signal Attenuation in 3G Transmission Lines
n 12G-SDI
In order to keep overall transmission line attenuation below the 30dB loss budget, it is necessary to calculate attenuation amounts individually for each section in the system. In the system shown below, the losses occurring within each transmission line have been calculated and entered into a level diagram. From this it is possible to see the differences in transmission distances possible with HD-SDI and 3G-SDI when using a coaxial cable (L-7CHD). If this shows that attenuation will surpass the specified loss budget, then it will be necessary to change to cables with less attenuation,
In 2015, SMPTE released ST 2082-1 12G-SDI, a standard for UHD-SDI (4K 2160p), as the next-generation of the single-link SDI format. 12G-SDI makes possible transmission of as much as eight times the data volume of HD-SDI (2K 1080i), and as much as four times the data volume of 3G-SDI (2K 1080p) over a single coaxial cable. At the same time, high performance is also required of both cables and connectors (refer to the table above), and Canare has already commenced efforts to meet these requirements.
<System Example>
20 dB @ 750 MHz (@ 742.5 MHz) 5 M–1.5 GHz 15 dB Return 1.5–3 GHz Loss 3–6 GHz 6–12 GHz Cable Loss
40 dB @ 6 GHz (@ 5.94 GHz) 15 dB 10 dB 7 dB 4 dB
4
HD Equipment
BCJ-JR
3 L-4.5CHD
5
6m
L-7CHD 105m
2
HD-SDI
125m
3G-SDI
105m
8 BCJ-JR
DVJB-W
9
L-2.5CHD 2m
DVJB-W
HD Equipment
6 BCJ-JR
1 L-2.5CHD
7
2m
L-4.5CHD 6m
Rack/Between the Racks
Between the Rooms
Rack/Between the Racks
<Level Diagram> 1
2
3
4
Attenuation (dB)
0
5 6
7
8
9 Margin
-20
n System Attenuation Format
Connector/ Cable m or pcs
HD-SDI
Loss (dB/m) Loss (total) (dB) m or pcs
3G-SDI
26
Loss (dB/m) Loss (total) (dB)
➀ L-2.5CHD
➁ DVJB-W
➂ L-4.5CHD
➃ BCJ-JR
➄ L-7CHD
➅ BCJ-JR
➆ L-4.5CHD
➇ BCJ-JR
➈ L-2.5CHD
2
1
6
1
125
1
6
1
2
0.3
0.9
0.2
0.2
0.1
0.2
0.2
0.2
0.3
0.6
0.9
1.2
0.2
12.5
0.2
1.2
0.2
0.6
2
1
6
1
105
1
6
1
2
0.4
0.9
0.3
0.2
0.2
0.2
0.3
0.2
0.4
0.8
0.9
1.8
0.2
21.0
0.2
1.8
0.2
0.8
Connectors
Sub Total
Margin
Total Amount
17.6 dB
2.4 dB
20.0 dB
27.7 dB
2.3 dB
30.0 dB
Active BNC
75Ω Active BNC Receptacles
Model
Description
Fiber-Optic Systems
Small BNC connector incorporates either a cable equalizer or a cable driver. Active BNC makes innovation in your 3G-SDI PC board layout. Built-in IC
BCA-TL
TX, Right Angle
Cable Driver
BCA-RL
RX, Right Angle
Cable Equalizer
BCA-TS
TX, Straight
Cable Driver
BCA-RS
RX, Straight
Cable Equalizer
BCA-TL
BCA-RS
(Right Angle)
(Straight)
• Standard package (5pcs)
Impedance of PCB
BNC Connector
Digital Signal Processing Part
Digital Signal Processing Part
50Ω
50Ω
Built-in
Space-saving
Simplify Your Circuit Design
3G-SDI SG
Specifications
DC 3.3V
BNC
L-5CFB 1m
L-5CFB
50mA
70mA
Operating Temperature
-25°C to +85°C
Output Signal Amplitude
800mVpp
—
Equalizing Cable Length
—
3G-SDI 120m w/L-5CFB
Weight
SMPTE 424M
10 20 30
Approx. 9.0g
40
US Patent No.: 8251721 B2 JP Patent No.: 4837715
0
Panel Hole Dim.
BCA-RL
1.5
3.0 (GHz)
BCA-TS
BCA-RS
3.4max
1 2. φ
1 2. φ
1.27
3.04 5.9
3.4max 3.04 5.9
1：GND 2：SDO－ 3：SDO+ 4：Vcc
10.16
t2.0 t2.0 (TOP VIEW) (TOP VIEW) Note: The darker shaded area will come into contact with the connector body.
P=1.27 9.64
Connectors
φ
2-
6
4
1.
φ
0.
4321
8
1：GND 2：SDI+ 3：SDI－ 4：Vcc 5：SD/HD 6：－ 7：－ 8：ENABLE
t2.0 (TOP VIEW)
4-
1.4
φ
P =1.27
4321 5
1.27 1.15
2-
3
1.
6
0.
φ
4-
2.7×3.6
4
1.
φ
2-
6
10.16
123 4
1：GND 2：SDI+ 3：SDI － 4：Vcc 5：SD/HD P =1.27 6 ： － 7：－ 8：ENABLE
1234
0.
2
3
1.
7
φ
6-
2.7×3.6
5
6-
φ
6 0.
8
t1.6 Screw: M2.6
Cable Assemblies
t1.6 Screw: M2.6 7
Mutichannel Systems
50
BCA-TL
-φ
Eye Pattern ( 3Gbps )
Return Loss
(dB) 0
SMPTE 424M, 292M, 259M, BTA S-004C, EN50083-9, RoHS
Compliant
PCB Hole Dim.
Active
BNC RX BCA-RL, BCA-RS
Supply Voltage Current Consumption
Active
Panels & Patchbays
TX BCA-TL, BCA-TS
Model
Cables
I/O 75Ω
I/O Block
Impedance of PCB
Active BNC
Connectors
l BNC connector integrated with a cable equalizer or a cable driver, and yet keep the connector size to a minimum. l Supports 3G-SDI, HD-SDI, SD-SDI and DVB-ASI l Offers an excellent return loss performance without designing 75 ohm I/O block l Simplifies PCB design process dramatically and will reduce entire development cost l PCB space saving and help to downsize devices l Easy to distinguish TX from RX by color-coded insulation
P=1.27 9.64
1：GND 2：SDO－ 3：SDO+ 4：Vcc
t2.0 (TOP VIEW) 27
Connectors 75Ω DIN Connectors
75Ω DIN1.0/2.3 Connectors Mini coax connectors IEC61169-29 and DIN 47 297 compatible. n DCP-C Series (Crimp Plugs) Model DCP-C25HD DCP-C3F DCP-C4F DCP-C53
VSWR 1.2@ 3GHz
Suitable Cable Canare Others L-2.5CHD, L-2.5CHLT 1855A, VDM230 L-3CFB — L-4CHD, L-4CFB 1505A, VPM2000 L-4.5CHD 1694A, VSD2001
Center Pin BN1148 BN1148 BN1158 BN1157
Sleeve
Boot
Die Set
BN7136 BN7003A BN7015A BN7138
— — — —
TCD-D253F TCD-D253F TCD-D534F TCD-D534F
•Standard package (20pcs/100pcs)
DCP-C25HD
SMPTE ST 424
l Our unique ball-locking mechanism offers smooth and reliable mating. l Canare crimp design ensures quick and reliable installation. l Elongated body design enables stable finger grip. l Return loss: 20 dB or greater up to 3GHz l Extraction tool : BET-DIN (see page 38)
DCP-C25HD
US Patent No.: 8764473 B2 Be sure to use Canare crimping tool for installing connectors on cables
n PCB Mount Receptacles
7
VSWR 1.2 @ 3GHz
Description Right Angle Right Angle, Long type Edge Mount
20.84
Nut Driver Bit
φ4.1
Model DCJ-LR DCJ-LR/1 DCJ-FEM
Rerurn Loss for DCP-C25HD
NDT-DIN
DCJ-LR
•Standard package (20 pcs)
l Compact design ideal for high density mounting and downsizing devices. l Combination of DCJ-LR/1 and DCJFEM will be effective for staggered arrangement. l Return loss: 20 dB or greater up to 3 GHz.
0.8
DCJ-LR/1
Note: Nut driver bit NDT-DIN is required. Rerurn Loss for DCJ-LR
n Adapters Model DCJ-JR BCJ-DCJ BCP-DCJ
DCJ-FEM
VSWR 1.1 @ 3GHz Description Panel Mount Jack to Jack Yes BNC Jack to DIN1.0/2.3 Jack Yes BNC Plug to DIN Jack No
Nut Driver Bit NDT-DIN N/A N/A
•Standard package (20 pcs)
DCJ-JR
l Return loss: 26 dB or greater up to 3 GHz. Note: Nut driver bit NDT-DIN is required for DCJ-JR
<Panel Hole Dim.> DCJ-LR DCJ-LR/1 DCJ-FEM DCJ-JR
<PCB Hole Dim.>
BCJ-DCJ
DCJ-LR DCJ-LR/1
DCJ-FEM BCJ-DCJ
t2.0
t2.0
t1.6
BCP-DCJ
n Nut Driver Bit Model NDT-DIN
Description 6.35mm (1/4") hex shank
NDT-DIN 28
Connectors
φ4.1
CANARE
27.95
75Ω Multichannel Coax Connectors
9.8
n Crimp Plugs
Fiber-Optic Systems
4K-DIN Coax Connectors Canare unique “4K-DIN” allows you to connect or disconnect 4 of 3G-SDI signals in one easy step. 9.8 Suitable Cable
Die Set
Description
MDM-V4C25HW
V4-2.5CHW
TCD-D253F
Male
MDF-V4C25HW
V4-2.5CHW
TCD-D253F
Female
9
(92)
(φ 28.4)
Model
MDM-V4C25HW
n Flush-mount Receptacle Jack to Jack
Connectors
l 75Ω 4-channel coax connector with push-pull locking mechanism. l Compact, solid, and lightweight nylon resin (PA 66) body l Return loss: 20 dB @ 3 GHz l MDF-V4JRU accepts MDM-V4C25HW and also DIN 1.0/2.3 plugs.
<Connection Example>
24 26
19
MDF-V4JRU MDM-V4C25HW
27.4
24
φ 23.95
Ex. 2
4
MDF-V4C25HW
φ2
MDM-V4C25HW
Cables
Ex. 1
Hole Dimensions
31
MDF-V4JRU
φ 22.4
75Ω DIN 1.0/2.3 plug ×4
31
27.4
26
19 Min. 44mm pitch (recommended)
Be sure to use the Canare crimping tool for installing connectors on cables.
Panels & Patchbays
75Ω Multi-pin Coax Connectors Handles five 75Ω coaxial connections. TCD-35CA
Plug
MCF-V5C3
V5-3C, L-3C2V, L-3C2VS
TCD-35CA
Receptacle
Description Dust Cap for MCM-V5C3
DCF01
Dust Cap for MCF-V5C3
(41.9)
M39x1.5
CANARE
DCM01
MCF-V5C3
(98)
Mutichannel Systems
Model
MCM-V5C3
(8.8) (26.2)
l 1.2 or less VSWR up to 1.5GHz. l Crimp system ensures quick and reliable installation.
Key
3.8
∅ 4− 7
5
∅3
1
31.98
* Replacement unit also available. MCM-V5C3: BN9078A MCF-V5C3: BN9079B
.66
V5-3C
∅3
MCM-V5C3
Be sure to use the Canare crimping tool for installing connectors on cables. 31.98
4 2
31.98 41.3
Description
∅36
Die Set
∅29
Suitable Cable
∅42 ∅34.4
Model
4
* Replacement crimp units also available: DCP-C25HW-ML for MDM DCJ-C25HW-ML for MDF
φ2
φ 23.95
MDF-V4C25HW
φ 22.4
MDF-V4JRU
(103.8)
Description
φ 28.6
Model
3
31.98 41.3
Replacement Unit BN9078A
Connectors
Cable Assemblies
Panel Hole Dimensions (Mounting screw M3 x 4 pcs)
Replacement Unit BN9079B
29
Connectors 75Ω BNC Connectors
75Ω BNC Crimp Plugs Canare True 75 Ω BNC Connectors has been widely used in the world with quick and reliable crimp design, and outstanding performance. The high-end model BCP-B series are specially designed for particular coax cables, and minimize return loss at 3 GHz. n BCP-B Series Model BCP-B25HD BCP-B25HW BCP-B26 BCP-B28 BCP-B3F BCP-B31F BCP-B4F BCP-B45HW BCP-B53 BCP-B56 BCP-B5F BCP-B51F
VSWR 1.1@ 3GHz
Suitable Cable Canare Others L-2.5CHD, L-2.5CHLT VDM230 V4-2.5CHW — — 1855A, 1855P 1855ENH, — HD PRO 0.6/2.8 AF L-3CFB, V*-3CFB — L-3CFW, V*-3CFW — 1505A, 1505ANH, VPM2000, L-4CHD, L-4CFB, V*-4CFB HD PRO 0.8/3.7 AF L-4.5CHWS 1694F L-4.5CHD 1694A — HD PRO 1.0/4.8 AF L-5CFB, V*-5CFB — L-5CFW, V*-5CFW —
Center Pin
Sleeve
Boot
Die Set
B11015E B11015E B11014E
BN7129 BN7143 BN7029C
CB02 CB02 CB02
TCD-35CA TCD-35CA TCD-35CA
B11015E
BN7052A
CB02
TCD-35CA
B11015E B11015E
BN7003A BN7015A
CB03 CB04
TCD-35CA TCD-4CA, TCD-451CA
B11016E
BN7015A
CB04
TCD-4CA, TCD-451CA
B11020D B11020D B11020D B11020D B11020D
BN7016 BN7046 BN7046 B75004A B75004A
CB05A CB05A CB05A CB05A CB05A
TCD-35CA TCD-35CA TCD-35CA TCD-5CF, TCD-55FA TCD-5CF, TCD-55FA
• Standard package (20pcs/100pcs)
BCP-A25 BCP-A25F BCP-A3 BCP-A31 BCP-A32 BCP-A3F BCP-A4 BCP-A42 BCP-A4F BCP-A5 BCP-A52 BCP-A55 BCP-A5F BCP-A77 BCP-VA3 BCP-VA5
Canare
Others L-2.5C2V — L-2.5CFB 1855A, 8218, 1417B, 1418B L-3C2VS, L-3C2V, V*-3C — L-3C2W — 1506A, 1824A, 1825A, 1826A, — 643948 L-3CFB, V*-3CFB — LV-61S 8241, 8279, RG-59B/U — 1505F 1505A, 1505ANH, 8212, 8241F, 9167, 9259, 9659, L-4CHD, L-4CFB, V*-4CFB VPM2000, HD PRO 0.8/3.7 AF L-5C2VS, L-5C2V, V*-5C — L-5C2W — — 1695A, VSD2001TS L-5CFB, V*-5CFB — LV-77S 8281F V*-3C — V*-5C —
Center Pin
Sleeve
Boot
Die Set
BN1018A B11014E B11014E B11014E
BN7029C BN7029C BN7003A BN7011
CB02 CB02 CB03 CB04
TCD-35CA TCD-35CA TCD-35CA TCD-31C
B11016E
BN7026A
CB03
TCD-35CA
B11015E B11015E B11016E
BN7003A BN7015A BN7011
CB03 CB04 CB04
TCD-35CA TCD-4CA, TCD-451CA TCD-31C
B11016E
BN7015A
CB04
TCD-4CA, TCD-451CA
BN7016 BN7014 BN7045A B75004A B75004A BN7052A BN7045A
CB05A — CB04 CB05A CB05A CB03 CB05A
BCP-C7FA BCP-C7HD
Canare L-1.5C2VS, V*-1.5C L-5CHD L-6CHD — L-7CFB L-7CHD
Others 83264, 83267 — — 7731A, 9064, 9292, 1617A, 9011 — —
TCD-35CA TCD-451CA TCD-35CA TCD-35CA TCD-5CF-TCD-55FA TCD-35CA TCD-35CA
Center Pin
Sleeve
Boot
Die Set
Solder BN1139 BN1083A
BN7022 B75004A BN7074A
CB01 CB05A —
TCD-1DB TCD-5HD TCD-67HD
BN1043A
BN7021A
—
TCD-7CA
BN1012B BN1082A
BN7021A BN7021A
• Standard package (20pcs/100pcs).
— —
TCD-7CA TCD-67HD *2: Excluding BCP-C1
l Canare crimp design ensures quick and reliable installation. l Gold plated “snap locks” center pin and beryllium copper outer contact. l Elongated body design enables stable finger grip (excluding BCP-C1). l Position mark on the BCP-B/A series body makes it easier to check if the connector is locked. Note: Die set for BCP-A5F is TCD-35CA
-40
0
1.5
3.0 (GHz)
Return loss for BCP-B53
BCP-A3 S11(dB) 0
VSWR
SMPTE ST 424 1.3 1.2
-20
1.1 -30
-40
-50
0
1.5
3.0 (GHz)
Return loss for BCP-A3
BCP-C6HD S11(dB) 0
VSWR
SMPTE ST 424
-10
1.3 1.2
-20
1.1 -30
-40
-50
0
1.5
3.0 (GHz)
Return loss for BCP-C6HD
Be sure to use the Canare crimping tool for installing connectors on cables. 30
1.1 -30
VSWR 1.1 @ 2GHz (*2) Suitable Cable
BCP-C71A
1.3 1.2
-20
*1: Excluding BCP-A25, BCP-A25F, BCP-A4
n BCP-C Series Model
-10
-10
B11016E B11016E B11020D B11020D B11016E B11014E B11016E
VSWR
SMPTE ST 424
VSWR 1.1 @ 2GHz, VSWR 1.2 @ 3GHz(*1) Suitable Cable
• Standard package (20pcs/100pcs). Note: Suitable die set for BCP-A5F is TCD-35CA; do not use TCD-5CF/TCD-55FA for BCP-A5F.
BCP-C1 BCP-C5HD BCP-C6HD
S11(dB) 0
-50
n BCP-A Series Model
BCP-B5F
Connectors
75Ω BNC Connectors
75 Ω BNC Crimp Plugs (Right Angle Type) n BCP-LC Series Canare L-3C2VS, L-3C2V,V*-3C L-3CFB, V*-3CFB L-5C2VS, L-5C2V, V*-5C L-5CFB, V*-5CFB
Others — — — —
Center Pin
Sleeve
Boot
Die Set
B11014E B11015E B11016E B11020D
BN7003A BN7003A BN7016 B75004A
— — — —
TCD-35CA TCD-35CA TCD-35CA TCD-5CF, TCD-55FA
Fiber-Optic Systems
Model BCP-LC3 BCP-LC3F BCP-LC5 BCP-LC5F
VSWR 1.1@ 2GHz Suitable Cable
• Standard package (20pcs)
BCP-LC3
l Canare crimp design ensures quick and reliable installation. l Gold plated “snap locks” center pin and beryllium copper outer contact.
Connectors
Be sure to use the Canare crimping tool for installing connectors on cables.
75 Ω Slim BNC Crimp Plugs n MBCP-C Series Model MBCP-C25F MBCP-C3F MBCP-C4
VSWR 1.1@ 1.5GHz Suitable Cable Canare
L-2.5CFB L-3CFB, V*-3CFB LV-61S L-4CFB, V*-4CFB L-4.5CHD L-5CFB, V*-5CFB
Center Pin
Sleeve
Boot
Die Set
B11014E B11015E B11015E
BN7029C BN7003A BN7015A
— CB24 CB25
TCD-35CA TCD-35CA TCD-4CA, TCD-451CA
B11016E
BN7015A
CB25
TCD-4CA, TCD-451CA
B11020D B11020D
BN7046 B75004A
CB26 CB26
TCD-35CA TCD-5CF, TCD-55FA
Cables
MBCP-C4F MBCP-C53 MBCP-C5F
Others 1855A, 8218, 1417B, 1418B — 8241, 8279, RG-59B/U 1505A, 1505ANH, 8212, 8241F, 9167, 9259 1694A, 9066, 9116, 9118, 9248 —
• Standard package (20pcs/100pcs) Body
∅12
CANARE
Crimp sleeve
15
Center contact 26.35
(10.7)
MBCP-C3F Conventional BNC Plug
Slim BNC Plug
S11(dB) 0
Be sure to use Canare crimping tool for installing connectors on cables.
VSWR
SMPTE ST 424 -10 1.3 1.2
-20
1.1
Panels & Patchbays
l Slim design: OD 12 mm l Compatible with 75 Ω BNC receptacles. l Canare crimp design ensures quick and reliable installation. l Gold plated “snap locks” center pin and beryllium copper outer contact.
-30
-40
-50
0
1.5
3.0 (GHz)
Return loss for MBCP-C3F
Mutichannel Systems
Technical Note Voltage Standing-wave Ratio (VSWR) and Return Loss Voltage
Vmax
Vmin
Coaxial cable distance
Fig. 1 Voltage Distribution Over Coaxial Cable
VSWR 2 1.5 1.2 1.1 1.05 1.02 1.01
Return Loss (dB) 9.5 14 20 26 32 40 46.1
Cable Assemblies
Terminating the receiving end of a limited length coaxial cable using a resistance value not equal to its characteristic impedance creates a reflected wave that returns back down the cable to the sending end. The result is interference developing between the travelling wave and the return wave which results in a standing wave that causes voltage levels to fluctuate. The degree to which terminating resistance matches the characteristic impedance is indicated using the VSWR or voltage standingwave ratio standard shown in Fig. 1. Going hand in hand with the VSWR ratio is the return loss factor which measures the size of the reflected wave current in relation to the travelling wave current. (See Fig. 2)
Fig. 2 VSWR to Return Loss Conversion Table
Connectors
31
Connectors 75Ω BNC Connectors
75Ω BNC Solder Plugs n BCP-H Series Model BCP-H3B BCP-H31F BCP-H45HW BCP-H5B BCP-H51F BCP-H5/1
VSWR 1.1@ 1GHz
VSWR
S11(dB) 0
Suitable Cable
SMPTE ST 424
Canare L-3C2VS, L-3C2V, L-3CFB L-3CFW L-4.5CHWS L-5C2VS, L-5C2V, L-5CFB L-5CFW, L-5CFB L-3C2VS, L-3C2V, L-3CFB L-5C2VS, L-5C2V, L-5CFB
Others — — 1694F — —
-10 1.3 1.2
-20
1.1 -30
BCP-H3B
-40
—
-50
• Standard package (20pcs)
0
1.5
3.0 (GHz)
Return loss for BCP-H3B
l The tubular (ferrule) section is silver plated to make soldering easier. l Cable stripper TS100E can be used. (Excluding BCP-H31F, BCP-H51F)
Model BCJ-C4
Suitable Cable RG-59 B/U, LV-61S, Belden 8241, 8279, 88241
Boot CB25
∅ 12
75Ω BNC Jack Plug Die Set TCD-4CA TCD-451CA
•Standard package (20pcs)
35.2
BCJ-C4 BCJ-C4
l 1.1 or less VSWR up to 1.5GHz, 1.2 or less up to 2.4GHz. l Beryllium copper (gold plated) is used on the center contact for its superior spring characteristics. (Center contact: solder) Be sure to use the Canare crimping tool for installing connectors on cables.
BCJ-J
75Ω BNC Extension Adapter Model BCJ-J
S11(dB) 0 -10
Description Jack to Jack
1.3 1.2
-20
1.1
BCJ-J
•Standard package (20pcs/100pcs)
-30
l Beryllium copper is used on the center contact for its superior spring characteristics. l 1.1 or less VSWR up to 2GHz. <Fig. 1>
-40
-50
0
1.5
3.0 (GHz)
Fig.1 Return loss for BCJ-J
75Ω BNC Termination Plugs Designed for true 75Ω termination Model BCP-TB BCP-TB-CH
VSWR
SMPTE ST 424
VSWR
S11 (dB) 0
SMPTE ST 424 -10
-20
Description
BCP-TA
True 75Ω Termination True 75Ω Termination with String
1.3 1.2 1.1
-30
BCP-TB
-40
BCP-TB
•Standard package (20pcs/100pcs)
-50
l Includes 1/4 watt resistance. l 1.1 or less VSWR up to 3GHz. <Fig. 2>
Fig.2 Return loss for BCP-TB and previous model BCP-TA
0
1.5
3.0 (GHz)
Connector Boots n CB0x Series Our best selling connector boots for Canare BNC, TNC crimp plugs. BP-xx
TNP-xx
C3, C4 C31 C5, C5FA
C3, C4 C31 C5
Model CB24 CB25 CB26
Colors Available C3F BLK, BLU, GRN, RED, YEL, WHT C4, C4F C5F
MBCP-xx
Typical Connectors RCAP-xx C3A, C3F C3GS, C4A, C4F C53, C5A, C5F
7.1
∅12.7
n CB2x Series Thinner type of CB0x series. Best fit for Canare Slim BNC, RCA, and F crimp plugs.
CB03, CB04, CB05A
∅6.58
Colors Available BCP-xx BLK, BLU, GRN, RED, YEL, WHT C1 B25HD, B25HW, B26, B28, A25, A25F B3F, B31F, A3, A32, A3F, VA3 BLK, BLU, BRN, GRN, GRY, ORN, PPL, RED, YEL, WHT B4F, A31, A4, A42, A4F, A55 B53, B56, B5F, B51F, A5, A5F, A77, VA5, C5HD
28
CB01, CB02
FP-xx C3, C3F C31, C4, C4F C5, C53A, C5F
∅10
Model CB01 CB02 CB03 CB04 CB05A
28
32
CB24, CB25, CB26 Connectors
75Ω BNC Connectors
75Ω BNC Receptacles BNC Receptacles emphasizing true 75Ω impedance.
Jack to Solder Jack to Solder w/Ground Lug Panel Jack (1/2") Panel Jack (7/16") Jack to Jack
4.8
BCJ-R/1 5.3 max
— —
1.5C-2V
TCD-1DB
—
10.9
ARE
BCJ-R BCJ-R/1 BCJ-FC1 BCJ-FC1-7/16 BCJ-JR
BCJ-R/1
Die Set
10.9
9.6
BCJ-R
12.1 3.5max
—
BCJ-FC1-7/16
BCJ-FC1-7/16
•Standard package (20pcs/100pcs) 20.5
6max
Description
BCJ-RU BCJ-RUD BCJ-RUDB BCJ-RUC1 BCJ-JRU BCJ-JRUD BCJ-JRUDB
Jack to Solder Panel Jack Jack to Jack
BCJ-FC1
φ14
Die Set
10.2 2
— TCD-1DB — — — — —
12.1
20.9
BCJ-JR
BCJ-JR
φ19.42
Model
Suitable Cable — 1.5C-2V — — — — —
7.2
Connectors
n Flush-mount Receptacles Flange Type ITT XLR-F77 Neutrik D Neutrik D (Black) ITT XLR-F77 ITT XLR-F77 Neutrik D Neutrik D (Black)
5
2 26.4
" 16
Suitable Cable — —
Description
" 14
Model
4.5max
2 29.9
10.9
φ13
n Standoff Receptacles
Fiber-Optic Systems
φ14
4.5max
•Standard package : 20pcs
2.4
27.5
BCJ-RU
l VSWR 1.1 @ 2GHz (Panel Jack: 1.1 @ 1GHz) l Gold plated beryllium copper center contact l Flush-mount receptacle prevents damage on the jack.
φ19.42
Cables
BCJ-RU
2.4
Standard design Canare BCJ-RU design
23
Registered design
Panels & Patchbays
BCJ-RUC1
φ19.42
BCJ-RUC1
2.4
31.4
BCJ-JRU
★BCJ-FC1-7/16
BCJ-RUC1 BCJ-RU BCJ-JRU
BCJ-RUD BCJ-RUDB BCJ-JRUD BCJ-JRUDB
BCJ-JRU
21.4
BCJ-FC1
23
★BCJ-R/1 ★BCJ-JR
Mutichannel Systems
BCJ-R
BCJ-
n Panel Hole Dimensions
2−∅ 3.4
2.7 25.2
6
. 23
24
∅
4.7
BCJ-RUD 19
Description
26
15
.6
25
∅ 17.5
∅ 11.2
∅ 12.8
∅ 12.7
∅ 12.8
∅
9.6 11.1 15
∅ 12.8
Panel Hole Dimensions Connectors
∅ 11.2
∅ 12.8
33 ∅ 11.2
Mountable panel thickness: 1.2~1.5mm: BCJ-FPLVA, BCJ-FPLHA, BCJ-R/1 1.2~3.0mm: BCJ-FPC, BCJ-FPC02, BCJ-JR, BCJ-FPLV01
∅ 11.2
15
.6
Note: Please remove washers from a connector before using IU-7/16.
IU-7/16
2.5
1
∅ 15 3.5
l Insulate a connector from a panel. l 5 colors available (white, black, blue, green, red, or yellow)
∅ 12.8
9.6 11.1 15
•Standard package: 20pcs
∅ 12.7
∅
ABS plastic
2.5
3.5
1
∅ 17.5
Cable Assemblies
Model IU-7/16
∅ 15
31
BCJ-RUD
Insulation Bushing
Neutrik D Compatible
30
ITT XLR-F77 Compatible
★ Indicate connectors that accept insulation bushing. Mounting hole for insulation bushing IU 7/16 should be adopted.
Connectors 75Ω BNC Connectors
75Ω BNC PCB Mount Receptacles (Screw Type) n BCJ-BP Series Model
Stud Position
Description
BCJ-BPLHA BCJ-BPLH2PA BCJ-BPLH3PA BCJ-BPC2P
Right Angle Right Angle, Dual Jack Right Angle, Triple Jack Straight, Dual Jack
Panel Mount
Standard Package
Front: M2.6 screw
20 pcs/100pcs 10 pcs 10 pcs 10pcs/100pcs
Horizontal —
* Screws are not included.
Key Features and Benefits l True 75Ω PC board mount receptacle. l VSWR 1.1 or less up to 1.5GHz, 1.2 or less up to 3GHz. (1.1 or less up to 1GHz, 1.2 or less up to 2.5GHz for BCJ-BPC2P.) l Gold plated beryllium copper center contact. l Can be fixed on the PC board with M2.6 screw for efficient soldering. (excluding BCJ-BPC2P) l Space-saving design allows high-density mounting. l Eliminates wiring material and cost.
BCJ-BPLHA BCJ-BPLH2PA BCJ-BPLH3PA
4.75
7.5
∅ 9.5
(28.94) 14.5
BCJ-BPLHA BCJ-BPLHA
(29.24)
16
∅ 9.5
14.5
M2.6
Note: Any cleaning solvents cannot be used. This leads to insulation problems. Insulation material: m-PPO (m-PPE)
SMPTE ST 424
-10
1.3 1.2
1.3 1.2
-20
1.1 -30
-40
-50
-50
1.5
3.0 (GHz)
Return loss for BCJ-BPLH, BCJ-BPLHA
-30
BCJ-BPLH2P
BCJ-BPLHA -40
BCJ-BPLH2PA
0
BCJ-BPC2P
10.9 3.1
1.5
-40
-50
3.0 (GHz)
0
1.5
3.0 (GHz)
Return loss for BCJ-BPC2P
Return loss for BCJ-BPLH2P, BCJ-BPLH2PA
2
2. 7 ∅
8
BCJ-BPLH3PA
BCJ-BPC2P
8
4
9.6
1.3 16
16
Screw: M2.6 t1.6 16
t2.0 (BOTTOM VIEW)
1.
∅
7.64
4
.8 1x 1
0.6
3-
10.16
10.16
t2.0 (BOTTOM VIEW)
10.16
10.16
t2.0 (BOTTOM VIEW)
Connectors
10.16 2.54
1.3
3
6-∅
1.
1.3
6.4 2-2.7X3.5
.1 ∅2
2.54
10.16
5−∅
16.5
3.4MAX
2.7X3.5 .1
2 2-∅
∅
5.08
6.4
5.08
7
9-
2.7×3.5
Screw: M2.6 t1.2 16
7 6.4
7
3.4MAX
3.4max
7 ∅ 2.1
16
4−
Screw: M2.6 t1.6 16
PCB Hole Dim.
TAP
4
9.6
9.6
∅1
Screw: M2.6 t1.6
34
M2.6
4
2-
7
7
2. ∅
.3
2.
8
11
.3
∅
∅
11
.95
R2
TAP
14
BCJ-BPLH3PA 3-
∅
Panel Hole Dim.
BCJ-BPLH2PA 2-
7
M2.6
BCJ-BPC2P
Comparison with the previous model
BCJ-BPLHA
17.5
1.1
16
-30
0
1.3 1.2
-20
1.1
∅ 9.5
BCJ-BPLH
(29.24)
16
-10
-20
14.5
BCJ-BPC2P
SMPTE ST 424
SMPTE ST 424
-10
VSWR
S11(dB) 0
VSWR
∅ 9.5
S11(dB) 0
BCJ-BPLH2PA
16.5 ∅ 9.5
VSWR
S11(dB) 0
TAP
t1.6 (BOTTOM VIEW)
75Ω BNC Connectors
75Ω BNC PCB Mount Receptacles (Hex Nut Type) Description Right Angle Right Angle, Low-cost Model Right Angle (10pcs) Right Angle Straight Straight, Low-cost Model
Stud Position
Panel Mount
Vertical
Front: Hex nut and lock washer
Horizontal
BCJ-FPLV01
BCJ-FPC02
—
3max
n BCJ-RP Series Description Right Angle Right Angle Straight, Through Hole Mount Straight, Surface Mount
Stud Position Vertical Horizontal —
Panel Mount Rear: Hex nut and lock washer
10.9
7.25 7.3
5.08
Connectors
BCJ-FPLVA
BCJ-RPC/1 VSWR
S11(dB) 0
4max
SMPTE ST 424
•Standard package (20pcs/100pcs)
2.3 2.1
-40
Note: Any cleaning solvents cannot be used. This leads to insulation problems. Insulation material: m-PPO (m-PPE)
Straight Type
-50
1.5
4.7
(16.17)
BCJ-RPLH 0
10.9
9.6
5 0.3
3.0 (GHz)
Return loss for BCJ-FPLVA, BCJ-RPLH
0.6 5.08
BCJ-FPLV01
VSWR
S11(dB) 0
Cables
Right Angle Type
1.1
BCJ-FPLVA
-30
RE
l VSWR 1.1 or less up to 1GHz, 1.2 or less up to 2.5GHz. (1.1 up to 3GHz for BCJ-FPLV-L) l Gold plated beryllium copper center contact.
1.3 1.2
-20
∅ 14
-10
3max
SMPTE ST 424 -10
（16.17）
Model BCJ-RPLV BCJ-RPLH BCJ-RPC BCJ-RPC/1
4.7 7.5
(16.17)
•Standard package (20pcs/100pcs)
7.5
Model BCJ-FPLVA BCJ-FPLV01 BCJ-FPLV-L BCJ-FPLHA BCJ-FPC BCJ-FPC02
Fiber-Optic Systems
n BCJ-FP Series
1.3 1.2
-20
1.1 -30
25.5
BCJ-FPLV01
-40
BCJ-FPLV-L
BCJ-FPLVA
BCJ-FPLV01
BCJ-FPC
BCJ-FPC02
-50
0
1.5
3.0 (GHz)
Return loss for BCJ-FPLV01, BCJ-FPLV-L
2.5
Panels & Patchbays
BCJ-FPLV-L
VSWR
S11(dB) 0
3.5
18.3
SMPTE ST 424 -10
BCJ-FPLV-L
BCJ-FPLHA
BCJ-RPC
BCJ-RPC/1
4.5max
1.3 1.2
-20
BCJ-FPC02
-40
-50
0
1.5
10.9
3.0
(GHz) Return loss for BCJ-FPC, BCJ-FPC02, BCJ-RPC
BCJ-RPLV
BCJ-FPC Panel BCJ-FPLV-L
4.5max 2.1
(16.17)
PC Board
10.9
* BCJ-FP series accept insulation bushing IU-7/16.
Mounting hole for IU-7/16 should be adopted. (See page 33)
0.8
RE
10 BCJ-FPLVA
1.2
BCJ-RPC/1 BCJ-RPC BCJ-RPLV BCJ-RPLH
18
BCJ-FPLHA*
BCJ-FPC* BCJ-FPC02*
BCJ-FPLV-L can be stacked over BCP-FPLVA on a PCB as shown.
27.5
9.6
1.4 3.5
BCJ-FPC02
BCJ-RPLV BCJ-RPLH
2max
BCJ-RPC
3 φ8.4
BCJ-FPC BCJ-FPC02
φ13
BCJ-FPLV-L
10.9
2
15
2.5
BCJ-RPC t 2.0
t 2.0
t 2.0
t 3.0
Connectors
t 1.6
35
Cable Assemblies
<PC Board Hole Dimensions> BCJ-FPLVA BCJ-FPLV01 BCJ-FPLHA
Mutichannel Systems
<Panel Hole Dimensions> BCJ-FPLVA* BCJ-FPLV01* BCJ-FPLV-L*
2.5 2 3 0.5 27
∅ 14
BCJ-RPLH
BCJ-RPC BCJ-FPC
φ8.4 φ14
-30
(16.17)
1.1
Connectors 75Ω BNC, 75Ω N
BNC Dust Caps Model
Description
BCJ-DC
Polyethylene (Black)
BCJ-DC-CH
Polyethylene (Black) with string
BCJ-DC
•Standard package (20pcs/100pcs)
l Protects unused BNC receptacles from dirt and dust.
BNC - RCA Adapter Model
Description
BCP-RCAJ
RCA Jack (F) to BNC Plug (M)
BCJ-RCAP
BNC Jack (F) to RCA Plug (M)
BCP-RCAJ
•Standard package (1pc)
l Gold plated center contact l Secure finger grip and reliable mating
BCJ-RCAP
NCP-H8HD
L-8CHD
∅ 23
Suitable Cable
(50)
NCP-H8HD
•Standard package (1pc)
l Gold plating on the contact pin prevents deterioration, even after years of use. l 1.1 or less VSWR up to 2GHz. <Fig. 3> l Solder type
VSWR
S11(dB) 0
SMPTE ST 424 -10 1.3 1.2
-20
1.1 -30
-40
Tools required: 17mm and 21mm wrenches
-50
0
1.5
3.0 (GHz)
Fig.3 Return loss for NCP-H8HD
H9.5
Caution: The connecting section of the N connector uses a shape that conforms to the IEC169-16’s 75Ω impedance standard. Note that the 50Ω N and other connectors that do not conform to this specification cannot be connected.
Model
Description
7/16-28 UNEF-2A max6
N (F) - BNC (F)
•Standard package (1pc)
VSWR
S11(dB) 0
l Beryllium copper (gold plated) is used on the center contact for its superior spring characteristics. l 1.1 or less VSWR up to 2GHz. <Fig. 4> l Panel mountable as well. For isolation from the panel, use Canare isolation bushing IU-7/16.(See page 33)
SMPTE ST 424 -10 1.3 1.2
-20
20.9
-40
0
1.5
3.0 (GHz)
12.5 39
1.1
Fig.4 Return loss for NCJ-BCJR
Connectors
HEX14
-30
-50
36
5/8-24 UNEF-2A
NCJ-BCJR
∅ 11.2
NCJ-BCJR
∅ 14.9
75Ω N to BNC Adapter
∅ 18
Model
∅ 21
75Ω N Solder Plug
9.6
Panel Hole Dimensions
75Ω Triaxial Connectors
Key Features and Benefits l True 75Ω, DC 1.5GHz; ≥20dB return loss (≤1.2 VSWR) l Push-lock mechanism - no cable stress when detaching to prevent cable break
l Reliable crimp system l Rugged and durable construction
Fiber-Optic Systems
75Ω Triaxial Connectors Canare CC series cover global triaxial interconnection. CC-F series are ideal for interconnecting European triax system and CC-K series for American triax system.
CC-F Series Cable compatibility meets European interconnecting requirements. Description
CCF5-JFC CCM5-PFC CCF5-JFRC CCM5-PFRC CCF7-JFC CCM7-PFC CCF7-JFRC CCM7-PFRC
Canare
Crimp type, Female cable mount Crimp type, Male cable mount Crimp type, Female panel mount Crimp type, Male panel mount Crimp type, Female cable mount Crimp type, Male cable mount Crimp type, Female panel mount Crimp type, Male panel mount
Suitable Cable Others
Belden: 7783A L-5CFTX Klotz: TRIAX8 Fujikura: 4.8/1.0 EFTXF Belden: 7784AS L-7CFTX Klotz: TRIAX11 Fujikura: SUPERFLEX11
Center contact BN9194 BN1135 BN9194 BN1135 BN9182A BN1131 BN9182A BN1131
Boot/Cap CB31 CB32 DCF02 DCM02 CB31 CB32 DCF02 DCM02
Sleeve A
Sleeve B
BN7120 BN7120 BN7120 BN7120 BN7113 BN7113 BN7113 BN7113
BN7121 BN7121 BN7121 BN7121 BN7114 BN7114 BN7114 BN7114
Crimp Tool TC-1 + TCD-65C
Connectors
Model
TC-2 + TCD-96C
(80.8) 37.5
CANARE
69.3
∅ 36
37.5
CANARE
2.5
Cables
∅ 23.5
76
CCF7-JFC CCM7-PFRC 37.5
Sleeve A
Sleeve B
CANARE
∅ 23.5
37.5
CANARE
∅ 24
Center Contact
(76) 56.3
2.5
78
(VSWR) 1.50
1.45
CCM7-PFC CCF7-JFRC
1.40
(90)
1.30
1.25
31
120
1.20
DCF02 ∅
3.
31
7
(90)
29
1.15
∅ 32
∅
CB31
∅3
24.5
.5
24.5
∅ 32
∅
3.
7
1.35
1.10
∅ 32
27.5
1.05
27.5
500MHz
140
CB32
1.5GHz
1.00 2GHz
VSWR for CCx7-F
Panel Hole Dimensions
DCM02
1GHz
Description
CCF4-JK CCM4-PK CCF4-JKR CCM4-PKR
Crimp type, Female cable mount Crimp type, Male cable mount Crimp type, Female panel mount Crimp type, Male panel mount
Retrofit Kit
Boot/Cap
Crimp Tool
BN9127A BN9128B BN9127A BN9128B
CB23 CB22 DCM02 DCM03
TC-1 + TCD-316C
Belden: 1856A, 1857A, 9267 Gepco: LVT61859, VT61859
L-4CFTX
78.7
37.5 (78.7)
Suitable Cable Others
Canare
2.5
18.7
(VSWR) 1.50
CANARE
∅ 28
37.5
CANARE
∅ 28.4
31
.5
∅3
1.40
1.35
∅ 77.2
37.5 77.2
1.30
1.25
18.7
2.5
18.7
31
31
CCF4-JKR 31
1.20
CCM4-PK
CANARE
∅ 29.9
∅ 37
37.5
CANARE
∅ 28.6
1.15
Panel Hole Dimensions
1.10
1.05
500MHz
CCM4-PKR
1GHz
1.5GHz
1.00 2GHz
VSWR for CCx4-K
Connectors
37
Cable Assemblies
1.45
CCF4-JK
Mutichannel Systems
CC-K Series Cable compatibility meets American interconnecting requirements. Model
Panels & Patchbays
∅ 32
Connectors RCA Connectors
RCA Pin Connectors n RCAP-C Series (Crimp Plugs) Suitable Cable
Model
Canare
RCAP-C25F RCAP-C25HD RCAP-C3A RCAP-C3GS RCAP-C3F RCAP-C42 RCAP-C4A
L-2.5CFB L-2.5CHD L-3C2VS, L-3C2V, V*-3C GS-6 L-3CFB, V*-3CFB — LV-61S
RCAP-C4F
L-4CFB, V*-4CFB
RCAP-C53 RCAP-C5A RCAP-C5F RCAP-C77
L-4.5CHD L-5C2VS, L-5C2V, V*-5C L-5CFB, V*-5CFB LV-77S
Others 1855A, 8218, 1417B, 1418B — — — — 1505F 8241, 8279, RG-59B/U 1505A, 1505ANH, 8212, 8241F, 9167, 9259, 9659 1694A, 9066, 9116, 9118, 9248 — — 8281F
Center Pin
Sleeve
Boot
Die Set
B11014E B11015E B11014E BN1093 B11015E B11016E B11015E
BN7029C BN7129 BN7003A BN7079 BN7003A BN7011 BN7015A
— — CB24 CB25 CB24 — CB25
TCD-35CA TCD-35CA TCD-35CA TCD-35D TCD-35CA TCD-31C TCD-4CA, TCD-451CA
B11016E
BN7015A
CB25
TCD-4CA, TCD-451CA
B11020D B11016E B11020D B11016E
BN7016 BN7016 B75004A B75004A
CB26 CB26 CB26 CB26
TCD-35CA TCD-35CA TCD-5CF, TCD-55FA TCD-5CF, TCD-55FA
•Standard package (20pcs/100pcs)
l Canare crimp design ensures quick and reliable installation. l The crimp tool for the RCAP-C can be used for the Canare crimp BNC plugs as well, thus saving on extra equipment. Be sure to use the Canare crimping tool for installing connectors on cables.
RCAP-C3A
n Solder Plugs Model
Description Plug Plug (long sleeve)
F-09 F-10
F-09
6max
l Robust metal shell l Comfortable grip l Cable OD up to 6.0 mm.
F-10
φ13
•Standard package (10 pcs)
7.5
22.8 35.6
RJ-JR
n Standoff Receptacle Description Jack to Jack
φ19.42
Model RJ-JR •Standard package: 20 pcs by insulation color
RJ-JR
29
2.4
l Insulation color is available in 5 colors (red, green, blue, yellow, white). l VSWR 1.2 @ 100Mhz
RJ-RU
RCA - RCA
φ23
RJ-RU
31
Neutrik D (Black)
19 26
•Standard package: 20 pcs by insulation color
RJ-JRUD RJ-JRUD φ19.42
l Three types of flanges are available. l Insulation color is available in 5 colors (red, green, blue, yellow, white). l VSWR 1.2 @ 100Mhz
<Panel Hole Dimensions> RJ-JR (*)
ITT XLR-F77 Flange
.4
φ3
2-
.6
RCA - BNC
2.7 4.7
24
RCA - Solder
Flange Type ITT XLR-F77 Neutrik D Neutrik D (Black) ITT XLR-F77 Neutrik D Neutrik D (Black) ITT XLR-F77 Neutrik D
31
Description
3 φ2
Model RJ-RU RJ-RUD RJ-RUDB RJ-JRU RJ-JRUD RJ-JRUDB RJ-BCJRU RJ-BCJRUD RJ-BCJRUDB
φ21.4
n Flush-mount Receptacles
Neutrik D Flange
2.4
31.4
2−∅ 3.4
2-φ3
19
RJ-BCJRU
(*) RJ-JR accepts insulation bushing IU-7/16; in this case, panel hole for IU-7/16 should be adopted (see page 33) 38
23
30
.6
23
24
∅
φ2
Connectors
1±
0.
2
18 25
RJ-BCJRU
F Connectors, Phone Plugs
Fiber-Optic Systems
F Connectors This type is used in such applications as home television receivers for cable television (CATV) systems. n FP-C Series (Crimp Plugs) Suitable Cable
Model FP-C25HD FP-C3 FP-C31 FP-C3F FP-C4 FP-C4F FP-C5 FP-C52 FP-C53A FP-C55A FP-C5F FP-C71A FP-C7FA
Others — — — — 8241, 8279, RG-59B/U 1505A, 1505ANH, 8212, 8241F, 9167, 9259, 9659 — — 1694A, 9066, 9116, 9118, 9248 1695A, 89120, 87120, 633948, 9116P — 7731A, 9064, 9292, 1617A, 9011 —
Center Pin
Sleeve
Boot
Die Set
BN1003B BN1002B BN1002B BN1003B BN1003B BN1004B BN1004B BN1004B BN1005B BN1005B BN1005B BN1041A BN1030A
BN7129 BN7003A BN7011 BN7003A BN7015A BN7015A BN7016 BN7014 BN7046 BN7045A B75004A BN7021A BN7021A
— CB24 CB25 CB24 CB25 CB25 CB26 — CB26 — CB26 — —
TCD-35CA TCD-35CA TCD-31C TCD-35CA TCD-4CA, TCD-451CA TCD-4CA, TCD-451CA TCD-35CA TCD-451CA TCD-35CA TCD-35CA TCD-5CF, TCD-55FA TCD-7CA TCD-7CA
Connectors
Canare L-2.5CHD L-3C2VS, L-3C2V, V*-3C L-3C2W L-3CFB, V*-3CFB LV-61S L-4CFB, V*-4CFB L-5C2VS, L-5C2V, V*-5C L-5C2W L-4.5CHD — L-5CFB, V*-5CFB — L-7CFB
•Standard package (20pcs/100pcs) VSWR
S11(dB) 0
SMPTE ST 424
-10
1.3 1.2
-20
1.1
FJ-JR
-30
-40
FP-C4
-50
FJ-FPC 0
1.5
Cables
l Lock mechanism improves reliability by preventing shifting or detaching of the center pin. l The tools and cable stripper can be used for the Canare crimp BNC plugs as well, thus saving on extra equipment. l VSWR of 1.1 or less up to 2GHz. Compatible with broadcast satellite (BS) and communications satellite (CS) signals. l Designed for indoor use.
3.0 (GHz)
Fig.1 Return loss for FJ-FPC and FJ-JR
Be sure to use the Canare crimping tool for installing connectors on cables.
n Standoff Receptacle φ19.42
Description Jack to Jack PC Board Straight Mount
•Standard package (20pcs/100pcs)
30 8.5
5 29.7
25 2-φ3
13.5
8.5
18 11.2
5 27.4
.2
31 φ21.4
30
±0
23
FJ-JRU φ2 1
FJ-JRU
18
Flange Type ITT XLR-F77 Neutrik D Neutrik D (Black)
5 27.4
8.5
26 2-φ3.4
8.5
3.6
φ2
24
0.2
31
1±
23
φ2
φ21.4
Jack to Jack
11.2
2.7 4.7
25 2-φ3
φ23
Description
φ21.4
0.2
2.7 4.7
25 2-φ3
φ23
FJ-FPC
n Flush-mount Receptacles
18
•Standard package: 20 pcs
11.2
2.7 4.7
l Three types of flanges are available.
5 27.4
8.5
19
26 2-φ3.4
FJ-JRUD
24
24
F-12 Round finish at the base
19
Others Two-piece construction
•Standard package (10pcs)
l Featuring a properly cable cramp system ensures long life reliability. l Suited to cables up to 6.0mm∅ in size.
F-11
3.6
Single-piece construction
19
φ2
3.5mm Mini Phone TS 3.5mm Mini Phone TRS 6.3mm (1/4") TS Phone 6.3mm (1/4") TRS Phone
Canare Phone Plugs
Cable Assemblies
26 2-φ3.4
Description
3.6
Phone Plugs
φ2
FJ-JRUD
31
Model FJ-JRU FJ-JRUD FJ-JRUDB
5 29.7
2.4
1±
Mutichannel Systems
2- ∅ 1.45
φ2
φ23
∅ 1.3
30
∅ 11.3
φ19.42
8.1
FJ-JR, FJ-FPC
8.5
5 29.7
φ19.42
2.4
13.5 2.4
PC Hole Dimensions
9.6
Model F-11 F-12 F-15 F-16
13.5
FJ-FPC
FJ-JR
23
3
Panel 2.5 Mount Hole Dimensions ∅ 1.1
∅ 9.5
l VSWR of 1.1 or less up to 2GHz. Compatible with broadcast satellite (BS) and communications satellite (CS) signals. <Fig. 1> l For insulation from the panel, use insulation bushing IU-7/16. (Panel thickness: 1.2~3.0mm)
Panels & Patchbays
Model FJ-JR FJ-FPC
F-15
No round finish
Canare’s durable design Connectors
F-16 39
Connectors 50Ω BNC Connectors
50Ω BNC Crimp Plugs VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz. n BP-C Series Model
Suitable Cable
Center Pin
Sleeve
Boot
BP-C3 BP-C31 BP-C4 BP-C5 BP-C5FA BP-C51
L-3D2V, 3D-2V L-3D2W, 3D-2W RG-58C/U, RG-58A/U L-5D2V, 5D-2V L-5DFB, 5D-FB L-5D2W, 5D-2W
BN1023A BN1023A BN1024A BN1025B BN1016C BN1025B
BN7003A BN7011A BN7030A BN7016A B75004A BN7002A
CB03 CB04 CB03 CB05A CB05A —
Center Pin BN1023A BN1025B
Sleeve BN7011 BN7002
Die Set (Model: TCD-***) 55FA 35D 3151D l l l l
BP-C5
l l
•Standard package (20pcs)
n BP-LC Series (Right Angle Type) Model BP-LC31 BP-LC51
Suitable Cable L-3D2W, 3D-2W L-5D2W, 5D-2W
Die Set TCD-3151D
•Standard package (20pcs)
BP-LC31
l Lock mechanism used on insulation improves reliability by preventing shifting or detaching of the contact pins. l Elongated body design for straight type enables easy attachment and removal. l Gold plating on the contact pin prevents deterioration, even after years of use. l Use of crimping to attach the connectors ensures quick, reliable installation.
VSWR
S11(dB) 0 -10
1.3 1.2
-20
1.1 -30
-40
-50
0
2.0
Return loss for BP-C31
4.0 (GHz)
Be sure to use the Canare crimping tool for installing connectors on cables.
max 6
BJ
Model BJ-JR
7/ 16- 28 UNEF-2A
∅ 14
50Ω BNC Receptacles n Standoff Description Jack to Jack
10. 9
2
20. 9 (33.8)
BJ-JR
BJ-JR
•Standard package (20pcs)
2 -∅ 3
13. 5
Flange Type ITT XLR-F77 Neutrik D
10. 9
31. 42
BJ-JRU 13. 5 13. 5 2. 4 2. 4
5 5 31. 42 31. 42
.2 2 ± 0 0. 21 1± ∅∅2
•Standard package (20pcs)
l Two types of flanges are available. l Flush-mount receptacle prevents damage on the jack.
18
25 2 -∅ 3 2 -∅ 3
23 23
Jack to Jack
5
2. 4
∅∅19.42 19.42 30 30
Description
BJ BJ- -
Model BJ-JRU BJ-JRUD
23
n Flush-mount Receptacles
10. 9 10. 9 18 18
25 25
BJ-JRU
∅ 14
50Ω BNC Extension Adapter Description Jack to Jack
BJ
Model BJ-J
10. 9
10. 9 33. 8
BJ-J
•Standard package (20pcs)
l VSWR of 1.1 or less up to 4GHz.
BJ-J VSWR
S11(dB) 0 -10
1.3 1.2
-20
1.1 -30
-40
-50
0
2.0
Return loss for BJ-J
40
Connectors
.2 ±0 21
30
∅
∅ 19.42
BJ -
l Mounting hole size is same as that for BCJ-R/1 connector.
4.0 (GHz)
50Ω TNC, 50Ω N, 50Ω SMA Connectors
50Ω TNC Crimp Plugs Model TNP-C3 TNP-C31 TNP-C4 TNP-C5 TNP-C51
Suitable Cable L-3D2V, 3D-2V L-3D2W, 3D-2W RG-58C/U, RG-58A/U L-5D2V, 5D-2V L-5D2W, 5D-2W
Boot CB03 CB04 CB03 CB05A —
TNP-C5F
L-5DFB, 5D-FB
CB05A
VSWR
S11(dB) 0
Die Set TCD-35D TCD-3151D
Fiber-Optic Systems
n TNP-C Series
-10 1.3 1.2
-20
1.1
TCD-35D
-30
TCD-3151D TCD-35DF TCD-55FA
-40
-50
TNP-C3
•Standard package (20pcs)
0
2.0
4.0 (GHz)
Return loss for TNP-C3
n TNP-LC Series (Right Angle Type) Suitable Cable L-3D2W, 3D-2W L-5D2W, 5D-2W
Die Set TCD-3151D
Connectors
Model TNP-LC31 TNP-LC51
•Standard package (20pcs)
l VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz. l Use of crimping to attach the connectors ensures quick, reliable installation. l Crimping tool can be used for the Canare crimp BNC plugs as well, thus saving on extra equipment. l Elongated body design for straight type enables easy attachment and removal. Be sure to use the Canare crimping tool for installing connectors on cables.
NP-C51 Cables
50Ω N Crimp Plugs
31
Boot CB04 —
Die Set
10
Suitable Cable L-3D2W, 3D-2W L-5D2W, 5D-2W
TCD-3151D
39.25
Model NP-C31 NP-C51
∅ 21
n NP-C Series
•Standard package (20pcs)
∅ 7.6
Suitable Cable L-3D2W, 3D-2W L-5D2W, 5D-2W
Die Set
Panels & Patchbays
Model NP-LC31 NP-LC51
15
n NP-LC Series (Right Angle Type) ∅ 5.4 ∅ 10
TCD-3151D
NP-LC31
•Standard package (20pcs)
l VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz. l Lock mechanism used on insulation prevents shifting or detaching of the contact pins. l Use of crimping to attach the connectors ensures quick, reliable installation.
NP-LC31
∅ 7.9
n SMAP-C Series Suitable Cable 1.5D-QEW L-3DFB L-3D2W, 3D-2W L-5D2W, 5D-2W
SMAP-C5F
L-5DFB, 5D-FB
8.5
Die Set TCD-1DB TCD-35DF
6.2 17.9 ∅ 4.6
Model SMAP-C1 SMAP-C3F SMAP-C31A SMAP-C51
SMAP-C1
Mutichannel Systems
50Ω SMA Crimp Plugs
∅ 3.25
Be sure to use the Canare crimping tool for installing connectors on cables.
8
TCD-3151D TCD-35DF TCD-55FA
SMAP-C1
•Standard package (20pcs)
L-5DFB, 5D-FB
∅5
SMAJ-C5F
Die Set TCD-35DF TCD-3151D TCD-35DF TCD-55FA
6.35
∅ 9.2
Suitable Cable L-3DFB L-5D2W, 5D-2W
7.5
SMAP-C31A
31.1
∅ 6.7
Model SMAJ-C3F SMAJ-C51
•Standard package (20pcs)
l Center contact for SMAP-C1 is of solder type. l VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz. (SMAP-C1: VSWR of 1.2 or less up to 2GHz.)
15
SMAJ-C3F
Be sure to use the Canare crimping tool for installing connectors on cables.
SMAJ-C3F Connectors
41
Cable Assemblies
n SMAJ-C Series
Connectors Cable Stripper, Crimp Tools
Coaxial Cable Stripper Three internal circular steel blades perform precise, extremely clean and easy stripping. Model
Preset to
TS100E
LV-77S·L-5CFB, V*-5CFB, V*-5C, LV-61S·L-4CFB, V*-3C
TS100U
L-2.5CHD, 1855A, 1505A, 1694A
l For most Canare BNC, DIN, RCA and F crimp plugs. l Rotary knob to select 5 different cable setups. l Make your own cable setting within cable O.D. 4mm~11mm l Hex wrench is attached on the lid top for quick adjustment. l One replacement blade included, and also sold separately. Replacement blade: TSC (1pc)
TS100E
Note: The following types of cables may not be accurately processed by Canare’s TS100 Cable Stripper, owing to their construction. 1. Cables employing such hard jacket material as polyethylene. 2. Cables employing such particularly soft insulator material as highfoam polyethylene. 3. Cables employing steel wire and semirigid pipe for outer conductor.
Turn cam knob to the right cable selection.
Straighten cable and insert into handle grip.
(mm)
Close lid, firmly grasp handle grip, and slowly rotate 7-10 times.
Push open lid, pull cable while firmly pressing yellow flag lever.
Insulation and jacket will be easily peeled off.
Crimp Tools Canare crimp tool offers reliable high-quality crimping performance in an easy-to-use design. n Die Sets
n Hand Crimp Tools
Model TCD-1DB TCD-31C TCD-3151D TCD-316C TCD-35CA TCD-35D TCD-35DF TCD-4CA TCD-451CA TCD-55FA TCD-5CF TCD-5HD TCD-65C TCD-67HD TCD-7CA TCD-96C TCD-D253F TCD-D534F
n Accessories
Model
Model TB-2A BET-12 BET-MBNC BET-DIN
Description Tool case Extraction tool for BNC straight plug Extraction tool for MBCP-C series Insertion / extraction tool for DCP-C series
Length — 12 inch 30 cm 30 cm
TC-1
TC-2 TC-1
l Select the appropriate die set to suit the individual connector l Hand crimp tool is required for die set, and sold separately l Die set are interchangeable
TB-2A (tools and connectors not included)
For crimp sleeves
BET-DIN
TC-1 BET-12
For center contacts 42
BET-MBNC Connectors
Crimp Tools
Crimp Connector Assembly Instructions
3.5
9
Crimp sleeve
19
Jacket
(mm) Stage
Whisker
Cutting chips
Aluminum wrapping tape
Center contact pin Crimp
Check crimp height Correct crimp position
Gap
Poor crimp position
Crimp
4. Slide crimp sleeve up against connector body over the braided shield until it butts against the connector body. Center the die over the crimp sleeve and crimp in place, using the specified crimp tool and die set. • Do not pull the cable while crimping is executed.
F A O
3. Tool Measuring Procedures Crimp force increases and crimp height decreases when the tool’s adjuster dial is turned in the direction of the 9. The dial is adjusted by first releasing it using a screw driver.
The actual contact surfaces on Canare’s BNC connectors are designed in conformance with JIS standards and therefore pose no compatibility problems.
Q Does it matter in which direction crimp sleeves are attached?
Canare BCP plug
A For BCP-A3–use and other non-stepped (straight type) crimp sleeves, it does not matter in which direction the crimp sleeve is attached. The attachment direction also does not matter for BCP-A5F–use and other specific-use types that have a chamfer (groove) at one end of the crimp sleeve.
MIL
Mutichannel Systems
However, stepped crimp sleeves such as those for BCP-C1, etc. are directional and must be attached in the direction shown in the diagram below, with the cable threaded through the sleeve starting from the end with the step (that is, the end with smaller-diameter hole).
Crimp height value= (A+B) /2 Refer to the separately included manual for the appropriate crimp height values for individual connectors.
Panels & Patchbays
Die-chamfered side
3. Hold the cable and push it into the connector body until the center contact is locked in place. You may feel a click sound when the center contact pin is locked. • Pull the cable gently (less than 4.5lbs or 19.6N) to confirm that is locked.
2. Measuring Frequency Crimp height is measured prior to commencing use of the crimp tool and always when changing the crimping die. After this, the crimp height is regularly measured after about each 1,000 crimps.
Cables
Example of installation using BNC
2. Place the center contact pin of the connector on the inner conductor of the cable and crimp the center contact pin at the correct position (without remaining a gap) as shown at left, using the specified crimp tool and die set. • To confirm the crimping properly, measure the crimp height after removing burrs with a knife. If it is not within the ideal value range, adjust the crimp tool. • Do not crimp the center contact pin at the stepped root end. • Confirm the center contact pin is crimped straight to the inner conductor. If the center contact pin is slanted, align it gently.
1. Measuring Crimping height Crimp height is measured after the crimp is made. As shown in the figure, the sum of the measured values for both directions is divided by two to arrive at the crimp height. The ideal value range for the BCP-A3 connector, for example, is 1.4mm to 1.5mm. When this value is lower (overcrimping occurs) than the recommended crimp height, the crimp becomes very hard. A value higher (undercrimping occurs) than the recommended value can result in increased electrical resistance and a physically weaker crimp. Either digital calipers or a micrometer should be used for measuring crimp height.
JIS Q Is it possible to use cables not listed in the connector compatibility table as long as they are close to the dimensions of those listed? A No. While connection may be possible, performance may be adversely affected.
Q What should be done with an aluminum foil shield? A Strip the aluminum foil shield to the root of the braided shield (to the edge of the jacket).
Q Why do some BNC plugs made by other companies have a sharp point at the tip of the central contact? Are these compatible with Canare’s BNC receptacles? A The central contact is pointed in conformance with the JIS standard for 50Ω BNC connectors. The central contacts on Canare’s connectors conform to the MIL standard, and therefore are not pointed. These two different shapes simply offer different ways to guide the plug into the female receptacle and have no direct effect on contact quality.
Even if the connection appears to work, factors such as electrical instability, weak cable contact strength and others may cause problems during actual use. Therefore, it is necessary to test and evaluate whether it is actually possible to use the configuration in question. Particular caution should be used when crimping is involved. Q What is meant by “cable contact strength”?
Cable Assemblies
If any aluminum foil shield is left on the cable, it may get stuck in the mouth of connector, making insertion impossible.
Connectors
Confirm compatibility of the connector and cable prior to assembly. 1. Slide the crimp sleeve over the cable and strip the jacket, braided shield, and insulation of the coaxial cable as shown at left. • For cables with stranded inner conductor, twist the strands in the same direction as plied after removing the insulation. • For a crimp sleeve with steps, slip it over the cable from the stepped end, as in the diagram. • If any aluminum foil shield is left on the cable, it may get stuck in the mouth of connector, making insertion impossible. • Remove all stray strands and offcuts of the aluminum foil shield to avoid possible short circuiting. • Make sure the inner conductor is free of all insulation debris and offcuts to ensure complete crimping.
Fiber-Optic Systems
Inner conductor Insulator Outer conductor (braided) Part A
Adjusting Crimp Tool
A Cable contact strength refers to the maximum load borne by the cable when exerting tensile force to remove it from the connector. For Canare products, “cable contact strength” refers to the contact strength of a cable’s outer conductor, not including the pull-out strength of the central contact or the contact strength of the inner conductor. Q What is the approximate insertion loss associated with connectors? A The value varies depending on the connector, but for BNC plugs the value is approximately 0.1dB per plug (DC–2GHz).
Connectors
43
Connectors Crimp Tools
Cables to Connector Cross-Reference n BNC, F, RCA, etc. Model
See page 43, for more information about the crimp height.
BCP-B
BCP-A
BNC
Crimp Plug BCP-C
MBCP-C
BCP-LC
Solder Plug BCP-H
Jack
F
RCA
FP-C
RCAP-C
Others
Suitable Die Set (*1)
Crimp Height
TCD-1DB
—
L-1.5C2VS/V*-1.5C
L-2.5C2V L-2.5CFB 1855A BCP-B26 1855P L-2.5CHD/L-2.5CHLT BCP-B25HD VDM230 1855ENH BCP-B28 HD PRO 0.6/2.8 AF 1506A BCP-B25HW V4-2.5CHW L-3C2V/L-3C2VS
BCP-A25 BCP-A25F
BCP-B3F
V*-3CFB 1695A VSD2001TS L-3C2W L-3CFW BCP-B31F V*-3CFW LV-61S RG-59B/U L-4CFB/V*-4CFB 1505A, 1505ANH HD PRO 0.8/3.7 AF BCP-B4F VPM2000 L-4CHD 1505F L-4.5CHD BCP-B53 1694A HD PRO 1.0/4.8 AF BCP-B56 BCP-B45HW L-4.5CHWS
RCAP-C25F FP-C25HD RCAP-C25HD
BCP-A32 TCD-35CA BCP-H3B BCP-H5/1
BCP-LC3F
RCAP-C3F
FP-C31
BCP-A4
MBCP-C4
TCD-31C
BCJ-C4
VWP-C4A MVP-C4
FP-C4
RCAP-C4A
MBCP-C4F
FP-C4F
RCAP-C4F
TCD-4CA or TCD-451CA
RCAP-C42
TCD-31C
MBCP-C53
FP-C53A
RCAP-C53
BCP-A42
BCP-LC5
BCP-H45HW BCP-H5B BCP-H5/1
TCD-35CA FP-C5
RCAP-C5A RCAP-C77
BCP-A5F (*2)
MBCP-C5F
BCP-LC5F
BCP-H5B BCP-H5/1 BCP-H51F
FP-C5F
TCD-5CF or TCD-55FA excluding BCP-A5F (*2)
RCAP-C5F
BCP-H51F
BCP-B51F BCP-A77 BCP-A52
RCAP-C77 FP-C52 BCP-C5HD BCP-C6HD BCP-C7HD BCP-C7FA
1.90 - 2.00
TCD-67HD
2.15 - 2.25
TCD-7CA
1.90 -2.00
— TCD-35D
— 2.01 -2.20
FP-C71A NCP-H8HD RCAP-C3GS
*1: Die set is not required for BCP-H series and NCP-H8HD *2: Suitable die set for BCP-A5F is TCD-35CA See page 40-41, for 50 ohm cables and connectors.
4K-DIN MD
MDM-V4C25HW MDF-V4C25HW
V4-2.5CHW
TCD-451CA TCD-5HD
FP-C7FA
BCP-C71A
DIN DCP-C
1.40 -1.50
BCP-A4F
L-2.5CHD/L-2.5CHLT DCP-C25HD 1855A VDM230
44
FP-C3F FP-C55A
n DIN 1.0/2.3, 4K-DIN
L-3CFB L-4CFB 1505A VPM2000 L-4.5CHD 1694A VSD2001
BCP-H3B BCP-H5/1
BCP-H31F
BCP-A5 BCP-VA5 BCP-A77
Model
RCAP-C3A MCM-V5C3 MCF-V5C3
BCP-A31
V*-5C
BCP-B5F
MBCP-C3F
FP-C3
BCP-A55
BCP-A5
LV-77S
MCM-V5C3 MCF-V5C3
BCP-LC3
BCP-A3F
L-5C2V/L-5C2VS
V*-5CFB L-5CFW V*-5CFW 8281F L-5C2W L-5CHD L-6CHD L-7CHD L-7CFB 7731A 9292 L-8CHD GS-6
MBCP-C25F
BCP-A3 BCP-VA3
V5-3C
L-5CFB
1.40 - 1.47
BCP-A3
V3-3C/V4-3C L-3CFB
BCJFC1(-7/16) BCJ-RUC1
BCP-C1
1.5C-2V
Suitable Die Set
Crimp height
TCD-D253F
1.08 -1.16
TCD-D534F
1.25 - 1.33
Belden: 1505A, 1505ANH, 1505F, 1506A, 1694A, 1695A, 1855A, 1855ENH, 1855P, 7731A, 8281F, 9292 Draka: HD PRO 0.6/2.8 AF, HD PRO 0.8/3.7 AF, HD PRO 1.0/4.8 AF Gepco: VDM230, VPM2000, VSD2001, VSD2001TS
DCP-C3F DCP-C4F
DCP-C53 Note: Be sure to use the right combination of cable, connector and die set for proper connection Connectors
Impedance Transformers
n Adapter Type Model BCJ-XJ-TRC
XLR3 (F) - BNC Jack
Description
BCJ-XP-TRC
XLR3 (M) - BNC Jack
BCJ-XJ-A10TRC
XLR3 (F) - BNC Jack, 10dB Attenuation Pad
BCJ-XJ-TRC
Fiber-Optic Systems
110Ω-75Ω Impedance Transformers Passively convert AES/EBU digital audio signals from 110Ω/XLR3 output to a 75Ω BNC coaxial cable and then back again to a 110Ω/XLR3 input.
n Panel Mount Type Model XJ3F-TRC-BCJ
Description (Front - Back) XLR3 (F) - BNC Jack
Flange Type
XJ3M-TRC-BCJ
XLR3 (M) - BNC Jack
BCJ-TRC-XP3F
BNC Jack - XLR (F)
BCJ-TRC-XP3M
BNC Jack - XLR (M)
XJ3F-A10TRC-BCJ
XLR3 (F) - BNC Jack, 10dB Attenuation Pad
BCJ-A10TRC-XP3F
BNC Jack - XLR3 (F), 10dB Attenuation Pad
ITT XLR-F77
BCJ-XJ-A10TRC
l SMPTE 276M and AES3 transmission standards l Coaxial transmission of 2 channel digital audio l Allows longer cable runs than 110 ohm twisted pair l AES/EBU signal distribution using Canare 75 ohm video patchbays
Cables
BCJ-XJ-TRC / BCJ-XP-TRC 75Ω BNC (unbalanced)
Connectors
BCJ-XP-TRC
XJ3F-TRC-BCJ
110Ω XLR3 (balanced) 2 0.47 µF TRANSFORMER
3
1
BCJ-TRC-XP3M Panels & Patchbays
Pin 1: Shell Pin 2: Hot Pin 3: Cold
BCJ-XJ-A10TRC 75Ω BNC (unbalanced)
110Ω XLR3 (balanced) 2 0.47 µF TRANSFORMER
10dB PAD
3
1
110Ω-75Ω Impedance Transformer: Input/Output Level Performance
9.0 10.0
1.60 2.39 3.18 3.60 3.98 4.78 5.58 6.38
AES/EBU Transmitter (V) 2.0 3.0 4.0 4.5 5.0 6.0 7.0 8.0
Transformer Out -10dB Pad (V) 0.50 0.75 1.01 1.13 1.26 1.51 1.76 2.02
7.18 7.98
9.0 10.0
2.27 2.52
Transformer Out (V)
BCJ-XJ-TRC/BCJ-XP-TRC
Panel Hole Dimensions
Cable Assemblies
AES/EBU Transmitter (V) 2.0 3.0 4.0 4.5 5.0 6.0 7.0 8.0
Mutichannel Systems
Pin 1: Shell Pin 2: Hot Pin 3: Cold
BCJ-XJ-A10TRC
Connectors
45