THE FOLLOWING PARTS ARE INCLUDED IN THE PACKAGE. PLEASE CONTACT YOUR DEALER IF ANY PARTS ARE MISSING.
DESCRIPTION
PART #
1
RUNGLOCK ASSEMBLY
075221 RH
1
RUNGLOCK ASSEMBLY
075221 LH
1
LEFT RUNGLOCK SPRING
391010 LH
1
RIGHT RUNGLOCK SRING
391010 RH
2
BOLT, 3/8 – 16 X 1 3/16
999380
2
LOCKNUT, 3/8-16
999569E
1
LATCH INSTRUCTION LABEL
911272
QTY
KIT # PK100C RUNG LOCK KIT To find out on which models you can use this kit, see the last page.
WARNING: ALWAYS REPLACE BOTH RUNG LOCKS ON YOUR LADDER. FOLLOW INSTRUCTIONS CAREFULLY. IF FURTHER ASSISTANCE IS NECESSARY, CONTACT LOUISVILLE LADDER GROUP CUSTOMER SERVICE AT 1-800-666-2811. LOUISVILLE LADDER CORP. 7765 NATIONAL TURNPIKE UNIT 190. LOUISVILLE KY 40214.
LATCH ON RIGHT HAND RUNG LOCK ONLY
(NOT SHOWN)
P/N 993002 REV-2
1
NOTE: LEFT HAND SHOWN BASE SECTION FLY SECTION RUNGLOCK BRACKET LOCKNUT
BASE RUNG
2
3 LEFT HAND SPRING
3/4” WRENCH BOLT SPRING
FLY RUNG
RIGHT HAND SPRING
RUNGLOCK 9/16” WRENCH BASE RUNG
Louisville Customer Care 1(800) 666-2811 www.louisvilleladder.com
DIMPLED SIDE OF LOCKNUT RUNG LOCK SPRING ENDS, SEE STEPS 5 & 7.
ASSEMBLY INSTRUCTIONS SPRING ASSISTED RUNG LOCKS WITH SHORT SHOULDER BOLT 4
SPRING
INCORRECT
5
CORRECT
6
SPRING
RUNG LOCK RUNG LOCK BRACKET
RUNG LOCK BRACKET
RUNG LOCK
RUNG LOCK BRACKET
RUNG LOCK
1) Lay Ladder on floor with the base or wide section of ladder resting on floor or proper work surface. Extend the fly or narrow section of ladder 2) 3) 4) 5) 6) 7) 8) 9) 10) 11)
approx. 6”, so that the rung locks are between two base rungs, as shown in figure 1. Remove one rung lock from bracket by removing the 3/8”-16 locknut, using a 9/16” and a 3/4” wrench, as shown in figure 1. Only one rung lock is to be taken off and replaced at a time. This is done so that you can use one rung as a guide to reassemble the other. Choose the proper new rung lock to replace the one removed. The right hand rung lock is equipped with a latch and the left hand is not. Determine which spring is required for the rung lock that you are about to assemble. The left hand spring must be used on the left hand side of the ladder and the right hand spring must be used on the right hand side of the ladder. See figure 2 to determine the correct spring. Reassemble the new rung lock, shoulder bolt and spring to the bracket where you have just removed the old rung lock. Finger tighten the locknut making sure the dimpled side of the locknut faces away from the rung lock. See figure 3. Make sure that the rung lock spring is positioned around the shoulder bolt with the short end of the spring hooked over the top of the rung lock bracket. The long end of the spring is not attached at this time. See figure 4. Using the 9/16” & 3/4” wrenches, tighten the locknut until it will not tighten anymore. Check to make sure that you did not pinch the spring between the shoulder bolt and rung lock bracket as shown in figure 5. Hold the long end of the spring and rotate it up between rung lock and rail, then hook over the top of the rung lock. See figure 6. Repeat steps 2-8 for the other rung lock. It is very important that BOTH rung locks be replaced to ensure proper operation. The rung locks should have some side play. This side play is to allow the rung locks to operate properly. Apply latch instruction label to rail above or below right hand rung lock assembly. DISCARD THE OLD FASTNERS AND RUNG LOCKS!!! Louisville Customer Care 1(800) 666-2811 www.louisvilleladder.com
KIT # PK100C RUNG LOCK KIT This kit can be used on the following models MODEL NUMBER
LADDER SIZE (XX)
MODEL NUMBER
LADDER SIZE (XX)
578-XX AE12XX CFGD12XX D59XX-2 L D62XX-2 L FE06XX FE22XX FE32XX FE42XX FE42XXHD FE52XX FE72XX R-3021-XX R-3022-XX R-3121-XX
16’ – 40’ 44’ – 48’ 16’ – 40’ 28’ 24’ – 32’ 16’ – 28 16’ – 40’ 16’ – 40’ 16’ – 28’ 20’ – 28’ 16’ – 28’ 16’ – 40’ 08’ – 40’ 40’ 36’ – 40’
*534-XX *618-XX *D-3121-XX *FE17XX *L-3022-XX *L-3022-XXPT *L-3121-XX *L-3221-XX *L-3221-XX-CAM
16’ – 40’ 16’ – 28’ 16’ – 20’ 16’ – 28’ 16’ – 40’ 16’ – 32’ 16’ – 28’ 16’ – 28’ 16'
* IF LADDER WAS MADE BETWEEN AUG 20TH./07TH - JAN/08 USE PK100R, IF NOT USE PK100C. Louisville Customer Care 1(800) 666-2811 www.louisvilleladder.com