Phone: 1-800-882-0008 (U.S.) Phone: 1-866-832-6753 (Canada) Phone: 1-847-742-7840 (International) Fax: 1-800-526-7268 (U.S. & Canada) Fax: 1-847-742-0261 (International) e-mail: info@skf.com website: http://www.skf.com Š Copyright SKF 2005 Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SPEEDI-SLEEVE, SKF and the SKF logo are trade marks of the SKF Group and are registered in certain jurisdictions. Printed in U.S.A. (rev 10/05)
Catalog 457027 October 2005
Speedi-Sleeve
速
The quickest and most economical way to repair worn shafts
Table of Contents
The Speedi-Sleeve® concept......................................................3 SPEEDI-SLEEVE®, the quickest and most sensible way to repair worn shafts The characteristics........................................................................4 A simple idea with an impressive effect Speedi-Sleeve® Gold.....................................................................5 The preferred choice for heavy-duty applications The installation..............................................................................6 From scored to restored in a few minutes Speedi-Sleeve® size listing • Speedi-Sleeve® for inch-size shafts....................................8 • Speedi-Sleeve® for metric shafts......................................14 Large diameter wear sleeves..................................................20 For shafts 8" to 45" (203mm to 1143mm) Wear sleeve request form........................................................21
Speedi-Sleeve® Gold with a relative surface hardness between 80 and 85 HRC for heavy-duty applications.
The Speedi-Sleeve concept 速
the quickest and sensible way to repair worn shafts
To seal efficiently, radial shaft seals must run against a smooth round surface - the seal counterface. If the counterface becomes worn, and it usually does, then the seal will no longer be able to fulfill its function, which is to retain lubricant and to exclude contaminants - solid particles as well as liquid.
To repair the shaft, it is usually necessary to dismantle the machine in order to be able to handle the shaft and then to grind down the counterface until it is smooth again. If the grooves are deep, the original size of the seal will no longer fit properly - a seal with a smaller shaft diameter has to be found.
Normally, the counterface will become grooved as a contaminant particle is caught under the seal lip and abrades a track as the shaft rotates. As this continues, the seal will allow more particles to pass or get stuck, and seal efficiency deteriorates, eventually leading to malfunction of the component the seal is meant to protect. To rectify the situation, it is necessary to repair the counterface on the shaft - a simple seal replacement will not be sufficient.
Now there is an easy way to repair the counterface with the shaft still in position and without having to look for a different size of seal. The answer is the Speedi-Sleeve速 from SKF.
3
The characteristics a simple idea with an impressive effect The Speedi-Sleeve速 has been developed by SKF a leading seal specialist - precisely to solve the problem of worn seal counterfaces at shaft ends. It is a thin-walled sleeve, with a high quality finish and hardness for its purpose, which is simply pushed in position over the worn shaft and after installing a new seal, the shaft is as good as new - if not better. There is no shaft dismantling or machining involved hence the "Speedi" - and costly downtime is saved. As the same size of seal as the original can be used, there is no need to search for other seals so that stock keeping is simplified, which results in time saved. No special equipment is required - the installation tool is supplied with the sleeve. A mallet and a pair of pliers are all that is needed for the repair job.
How it works The sleeve is sufficiently thin-walled (.011" or .28 mm) to allow the same size of seal to be used. The Speedi-Sleeve速 is made of high quality stainless steel SAE 304. The surface is wear-resistant and machined without directionality to a finish of Ra = 10 to 20 microinches or 0.25 to 0.5 袖m. This is, in fact, a better counterface than can normally be achieved on a shaft. If an external all-rubber V-ring is added to the sealing arrangement, there is little risk of contaminants reaching the primary seal and causing wear.
Size range The standard range covers shaft diameters from .500" to 8.000" (12.70 to 203.20 mm). Depending on production quantities, non-standard sizes can be quoted and produced. Each inch or metric sleeve fits a range around their base nominal shaft diameter.
Speedi-Sleeve速: good as a new shaft, if not better
4
Speedi-Sleeve Gold ®
The preferred choice for heavy duty applications Abrasion Resistance
Speedi-Sleeve® Gold
Comparison of various Speedi-Sleeve® coatings
®
Speedi-Sleeve Gold is an enhanced version of the popular Speedi-Sleeve® which offers improved resistance to abrasive wear. Designed to be used in applications where extended seal system life is needed, Speedi-Sleeve® Gold bridges the performance gap between the standard sleeve and expensive custom shaft treatments. A thin metallic film applied to the base stainless steel imparts a gold color and significantly increases durability and surface hardness (to approx. 2300 Vickers*). The Gold version is particularly effective in high dust and grit environments when combined with a LongLife seal. Yet installation is as easy as the original Speedi-Sleeve® and the same seal size can still be used. Gold is available from stock for dozens of shaft sizes or run from production in small quantities.
0 Speedi-Sleeve® Gold
20
Diamond coating
40 60 80 100 Standard sleeve
120 140 160
Nickel plated
Test results The Speedi-Sleeve® Gold has been thoroughly tested to establish its degree of abrasion resistance in severe dust environments using both coarse and fine sand. The tests were carried out at temperatures up to 225 oF (107.2oC) and at shaft speeds of up to 1693 fpm (8.6 m/s).
Testing in highly abrasive conditions demonstrates how the hardened surface of Speedi-Sleeve® Gold resists wear
Under these conditions, seals on shafts without Speedi-Sleeve® protection started to leak after 450 hours on average. Seals on Speedi-Sleeve® Gold ran for an average of 2,500 hours. In other tests, for example, it was found that continuous salt spray at 95oF (35oC) produced no trace of corrosion even after 600 hours.
Availability Select inch and metric sizes of Speedi-Sleeve® Gold are in stock. These cover the many common shaft sizes. Other sizes (up to 8.000" or 203.20 mm) can be quoted and produced to special order upon request.
50 sizes of Speedi-Sleeve® Gold are in production. Other sizes can be produced to special order.
* Due to the thin wall construction of Speedi-Sleeve®, this can only be accurately measured using highly specialized instruments and methods.
5
Installation From scored to restored in a few minutes Although installation is simple, it should be done carefully to achieve the best results.
2
Measure the diameter where the sleeve will be positioned on an unworn portion of the shaft. Measure in three positions and average the readings (to insure the shaft is within recommended specifications). If the average diameter is within the range for a given sleeve size, there is sufficient press-fit built into the sleeve to prevent it from sliding or spinning without the need for cement adhesive.
3
Determine how far back the sleeve must be positioned to cover the old seal wear track. Measure to the exact point, or mark directly on the surface. The sleeve must be placed over the worn area, not just bottomed or left flush with the end of the shaft.
Before starting, the sealing zone on the shaft should be carefully cleaned and any burrs or rough spots should be filed down and polished. Deep wear grooves, scratches or very rough surfaces should be treated with a suitable powdered metal epoxy filler. The sleeve must be positioned on the shaft before the filler has hardened. ®
It should also be noted that although Speedi-Sleeves can be easily installed within minutes on most shafts, they should not be placed over splines or keyways etc. on the shaft. As the thin-walled sleeve has an interference fit, any disturbances on the shaft surface may create a similar 4 pattern on the sleeve surface and the seal will leak.
Choosing the right size To determine the appropriate sleeve size it is first necessary to clean the shaft carefully. The diameter of an undamaged section of the seal counterface should then be measured in at least three different planes. The arithmetical mean of these measurements is used to choose a Speedi-Sleeve®. If the value lies within the permissible range shown in the product table for the shaft diameter (A) then the Speedi-Sleeve® will have an adequately tight fit on the shaft. The sleeve cannot turn on the shaft and no adhesive is required. If no suitable sleeve is listed in the product table, then it will be necessary to rework the shaft to an appropriate dimension. This will also mean that a new size of seal will be required. If production quantities are viable, SKF will also make tailored sleeves.
SKF Speedi-Sleeve® Installation Note: If you can catch your fingernail in a seal wear track or shaft groove, a repair sleeve should be installed to prevent leakage.
1
6
Clean the shaft where the seal contacts the shaft. File down and polish any burrs or rough spots.
5
Shallow wear grooves do not require filling. Optionally, a light layer of non-hardening sealant can be applied to the inner surface of the sleeve. Clear away sealant that migrates to the outer sleeve surface. If the shaft is deeply scored, (see note above) fill the groove with powdered metal epoxy type filler.* Install the sleeve before the filler hardens, allowing the sleeve to “wipe” off any excess filler. Clean away any residue and check that no filler is deposited on the sleeve O.D. surface. (continued next page)
6 Place installation tool over the sleeve. The flange end of the sleeve goes on the shaft first. 7 Gently tap the center of the tool until the sleeve covers the seal worn surface. If the installation tool supplied with the sleeve is too short, a length of pipe or tubing with a squared-off, burr-free end can be substituted. Use care not to scratch the precision ground sleeve O.D.
2
Measure shaft diameter in three places.
6
Place installation tool over Speedi-Sleeve®.
8 Leave the flange intact unless clearance is required. If the flange is to be removed, one precut of the flange perpendicular to the tear-off groove will aid in removal. Use heavy-duty side cutters or metal shears. Caution – cut only into the tear-off groove, not on to the finished sleeve surface. After positioning the sleeve, use standard pliers and flex the flange back and forth around its circumference and along the shaft axis. The flange will break loose along tear-off groove. Alternately, pry the flange away from the seal surface and twist it into a coil but take care not to lift the end of the sleeve off the shaft or it will leave a jagged edge. Flange removal must be done with care to avoid damage to sealing surface. 9 After the sleeve is installed, check again for burrs, which could damage the seal. 10 Lubricate the sleeve with the system media when installing the seal. 11 Proceed with the seal installation.
7
Tap tool to install Sleeve over shaft.
*Loctite “Quickmetal” (#66010) or similar works well for filling a groove and can be used as an adhesive or sealant if desired. Use of an adhesive can make the removal of the seal difficult. SKF Speedi-Sleeve® Removal A Speedi-Sleeve® can be dismounted in one of the following ways: by applying heat to the sleeve; by using a pair of wire cutters starting at or near the flange and applying a twisting action; by “peening” with a small hammer across the full width of the sleeve to expand it or, if accessible, by using a drift on the flange. A Speedi-Sleeve® cannot be reused.
8
Pry flange off installed Speedi-Sleeve®.
7
Speedi-Sleeve size listing - Inches “Y” Overall width
Removable flange Seal Surface 10/20 Micro Inches Ra finish with no machine lead
“D” Flange diameter
Tool Speedi-Sleeve
“A” Shaft diameter range
Nominal shaft diameter
0.472 0.500 0.551 0.563 0.591 0.625 0.625 0.630 0.669 0.684 0.709 0.750 0.750 0.760 0.781 0.787 0.813 0.859 0.866 0.866 0.875 0.875 0.910 0.910 0.945 0.969 0.969 0.984 0.984 1.000 1.000 1.024 1.063 1.063 1.089 1.102 1.102 1.125 1.125 1.125 1.156 1.156 1.175 1.181 1.188 1.219 1.240 1.250
.125 (3.18mm) Maximum Radius
Shaft
“X” Width on shaft “Z” installation depth
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99049 99050 99055 99056 99059 99810 * 99062 99058 99068 99060 99082 99811 * 99076 99081 99080 99078 99083 99086 99084 99085 99812 * 99087 99860 * 99091 99092 99094 99096 99813 * 99098 99814 * 99100 99103 99815 * 99106 99108 99866 * 99111 99816 * 99112 99116 99865 * 99120 99122 99114 99118 99123 99141 99817 *
0.236 0.250 0.250 0.250 0.197 0.313 0.313 0.313 0.315 0.313 0.315 0.313 0.313 0.313 0.313 0.315 0.375 0.250 0.259 0.315 0.313 0.313 0.313 0.313 0.313 0.313 0.625 0.313 0.313 0.313 0.313 0.315 0.313 0.313 0.313 0.375 0.375 0.313 0.313 0.375 0.375 0.375 0.313 0.315 0.313 0.313 0.315 0.313
0.331 0.344 0.391 0.391 0.354 0.406 0.406 0.438 0.433 0.438 0.433 0.438 0.438 0.438 0.438 0.433 0.563 0.375 0.359 0.472 0.438 0.438 0.438 0.438 0.438 0.438 0.719 0.433 0.433 0.438 0.438 0.472 0.438 0.438 0.438 0.500 0.500 0.438 0.438 0.500 0.500 0.500 0.438 0.433 0.438 0.433 0.438 0.438
0.610 0.610 0.750 0.750 0.750 0.750 0.750 0.718 0.875 0.900 0.962 0.945 0.945 0.938 0.935 0.930 0.000 1.155 1.188 1.188 1.094 1.094 1.218 1.218 1.130 1.130 1.130 1.300 1.300 1.219 1.219 1.313 1.320 1.320 1.406 1.375 1.375 1.500 1.500 1.500 1.350 1.350 1.400 1.400 1.400 1.563 1.540 1.500
"A" Shaft diameter range Minimum Inches
0.469 0.498 0.547 0.560 0.589 0.623 0.623 0.626 0.667 0.682 0.704 0.748 0.748 0.759 0.780 0.785 0.812 0.857 0.861 0.861 0.873 0.873 0.908 0.908 0.940 0.966 0.966 0.982 0.982 0.998 0.998 1.019 1.060 1.060 1.087 1.100 1.100 1.123 1.123 1.123 1.154 1.154 1.173 1.179 1.185 1.216 1.237 1.247
Maximum Inches
0.475 0.502 0.551 0.566 0.593 0.627 0.627 0.630 0.671 0.686 0.709 0.752 0.752 0.761 0.784 0.789 0.815 0.861 0.866 0.866 0.877 0.877 0.912 0.912 0.945 0.970 0.970 0.986 0.986 1.002 1.002 1.024 1.064 1.064 1.091 1.104 1.104 1.127 1.127 1.127 1.158 1.158 1.178 1.184 1.190 1.222 1.243 1.253
* Indicates Speedi-Sleeve Gold product
8
"Z" Installation depth
1.875 2.000 1.831 1.831 1.862 2.000 2.000 2.000 2.000 2.000 1.811 2.000 2.000 2.000 2.000 2.000 3.000 2.000 1.856 1.812 2.000 2.000 1.847 1.847 2.000 2.000 2.000 2.000 2.000 2.000 2.000 1.813 1.843 1.843 0.625 1.843 1.843 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.688 0.625 0.688 0.688
Speedi-Sleeve size listing - Inches (Cont.)
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99871 * 99125 99128 99121 99818 * 99129 99131 99134 99819 * 99820 * 99133 99138 99139 99146 99821 * 99143 99144 99147 99822 * 99823 * 99149 99150 99152 99155 99824 * 99156 99159 99153 99825 * 99157 99160 99163 99826 * 99161 99162 99166 99169 99873 * 99165 99167 99168 99182 99171 99170 99827 * 99828 * 99172 99174 99175 99180 99829 * 99176 99830 * 99177 99179 99831 * 99181 99185 99186 99832 *
0.625 0.313 0.315 0.591 0.500 0.250 0.500 0.500 0.500 0.512 0.313 0.500 0.512 0.512 0.563 0.563 0.375 0.512 0.563 0.375 0.563 0.375 0.438 0.438 0.563 0.563 0.625 0.390 0.512 0.512 0.500 0.500 0.563 0.313 0.563 0.445 0.563 0.563 0.550 0.313 0.563 0.500 0.563 0.375 0.563 0.750 0.375 0.563 0.750 0.531 0.563 0.563 0.551 0.551 0.667 0.563 0.563 0.563 0.889 0.563
0.750 0.438 0.438 0.709 0.625 0.375 0.625 0.625 0.625 0.630 0.438 0.625 0.630 0.669 0.688 0.688 0.500 0.669 0.688 0.500 0.688 0.500 0.563 0.563 0.688 0.688 0.750 0.509 0.630 0.630 0.641 0.625 0.688 0.438 0.688 0.571 0.689 0.689 0.689 0.438 0.688 0.625 0.688 0.500 0.688 0.875 0.500 0.688 0.875 0.625 0.688 0.688 0.669 0.669 0.800 0.688 0.688 0.688 1.025 0.688
1.500 1.500 1.500 1.594 1.594 1.600 1.594 1.625 1.638 1.638 1.638 1.638 1.638 1.781 1.781 1.781 1.781 1.781 1.781 1.781 1.781 1.781 1.859 1.859 1.859 1.859 1.859 1.850 1.850 1.850 1.938 1.938 1.875 1.875 1.875 2.087 2.087 2.087 2.087 1.906 1.906 1.906 2.031 2.063 2.063 2.063 2.055 2.063 2.063 2.063 2.063 2.063 2.087 2.087 2.125 2.090 2.090 2.156 2.188 2.203
"A" Shaft diameter range Nominal shaft diameter
1.250 1.250 1.260 1.299 1.313 1.313 1.313 1.339 1.375 1.375 1.375 1.375 1.375 1.417 1.438 1.438 1.438 1.496 1.500 1.500 1.500 1.500 1.523 1.552 1.563 1.563 1.569 1.575 1.578 1.578 1.605 1.614 1.625 1.625 1.625 1.650 1.650 1.654 1.656 1.688 1.688 1.693 1.719 1.739 1.750 1.750 1.750 1.750 1.750 1.750 1.766 1.766 1.772 1.772 1.781 1.813 1.813 1.859 1.868 1.875
Minimum Inches
1.247 1.247 1.257 1.297 1.310 1.308 1.310 1.333 1.371 1.375 1.371 1.371 1.375 1.411 1.432 1.432 1.435 1.490 1.497 1.497 1.497 1.497 1.520 1.549 1.559 1.559 1.566 1.569 1.572 1.572 1.602 1.608 1.622 1.622 1.622 1.647 1.647 1.647 1.653 1.685 1.684 1.687 1.715 1.736 1.747 1.747 1.747 1.747 1.747 1.747 1.761 1.761 1.769 1.769 1.778 1.809 1.809 1.857 1.866 1.872
Maximum Inches
1.253 1.253 1.263 1.301 1.316 1.314 1.316 1.339 1.377 1.381 1.377 1.377 1.381 1.417 1.438 1.438 1.441 1.496 1.503 1.503 1.503 1.503 1.526 1.555 1.565 1.565 1.572 1.575 1.578 1.578 1.608 1.614 1.628 1.628 1.628 1.654 1.654 1.654 1.659 1.691 1.690 1.693 1.721 1.742 1.753 1.753 1.753 1.753 1.753 1.753 1.767 1.767 1.775 1.775 1.784 1.815 1.815 1.863 1.872 1.878
"Z" Installation depth
2.000 0.688 0.688 1.000 0.813 0.813 0.813 0.813 0.813 0.813 0.813 0.813 0.813 0.984 1.016 1.016 1.016 0.984 1.016 1.016 1.016 1.016 1.016 1.016 1.016 1.016 1.016 1.000 1.023 1.023 1.000 1.016 0.813 1.016 0.813 0.846 0.827 0.827 0.827 0.875 0.875 0.844 0.813 0.813 0.813 0.813 0.813 0.813 0.813 0.878 0.813 0.813 0.812 0.812 1.062 1.000 1.000 1.000 1.000 1.000
* Indicates Speedi-Sleeve Gold product
9
Speedi-Sleeve size listing - Inches (Cont.)
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99184 99187 99188 99190 99189 99192 99833 * 99193 99196 99198 99834 * 99835 * 99199 99200 99204 99205 99836 * 99210 99212 99863 * 99215 99218 99220 99861 * 99229 99230 99226 99837 * 99838 * 99225 99227 99219 99231 99233 99869 * 99235 99241 99839 * 99237 99238 99240 99242 99243 99244 99249 99840 * 99248 99250 99253 99251 99841 * 99254 99256 99259 99261 99842 * 99260 99262 99264 99266
0.375 0.563 0.295 0.175 0.551 0.375 0.563 0.563 0.551 0.563 0.563 0.875 0.563 0.875 0.500 0.781 0.781 0.500 0.781 0.787 0.787 0.781 0.500 0.500 0.500 0.781 0.764 0.781 0.313 0.781 0.313 0.787 0.781 0.750 0.787 0.787 0.370 0.781 0.781 0.594 0.526 0.500 0.781 0.500 0.781 0.781 0.500 0.781 0.555 0.781 0.787 0.787 0.781 0.781 0.781 0.781 0.500 0.781 0.781 0.750
0.516 0.688 0.415 0.295 0.668 0.500 0.688 0.688 0.668 0.704 0.688 1.000 0.688 1.000 0.625 0.938 0.938 0.750 0.938 0.905 0.905 0.938 0.625 0.625 0.625 0.906 0.900 0.938 0.438 0.938 0.438 0.938 0.938 0.875 0.905 0.905 0.450 0.938 0.938 0.750 0.683 0.625 0.938 0.625 0.938 0.938 0.656 0.938 0.650 0.906 0.905 0.905 0.938 0.938 0.938 0.938 0.625 0.938 0.906 0.875
2.203 2.203 2.203 2.203 2.205 2.219 2.219 2.219 2.244 2.313 2.406 2.406 2.406 2.406 2.469 2.469 2.422 2.422 2.422 2.441 2.441 2.500 2.531 2.531 2.531 2.531 2.563 2.531 2.531 2.531 2.531 2.598 2.688 2.750 2.785 2.785 2.785 2.750 2.750 2.750 2.750 2.828 2.828 2.828 2.875 2.820 2.828 2.820 2.820 2.828 2.850 2.850 2.891 2.990 3.047 3.047 3.047 3.047 3.047 3.125
"A" Shaft diameter range Nominal shaft diameter
1.875 1.875 1.875 1.875 1.891 1.912 1.938 1.938 1.969 1.980 2.000 2.000 2.000 2.000 2.047 2.063 2.125 2.125 2.125 2.165 2.165 2.188 2.205 2.230 2.230 2.230 2.240 2.250 2.250 2.250 2.250 2.283 2.313 2.328 2.362 2.362 2.362 2.375 2.375 2.375 2.375 2.438 2.438 2.441 2.492 2.500 2.500 2.500 2.500 2.516 2.559 2.559 2.563 2.598 2.621 2.625 2.625 2.625 2.625 2.677
Minimum Inches
1.872 1.872 1.872 1.872 1.887 1.909 1.934 1.934 1.965 1.977 1.997 1.997 1.997 1.997 2.040 2.057 2.124 2.123 2.124 2.162 2.162 2.186 2.198 2.227 2.227 2.227 2.237 2.249 2.249 2.249 2.249 2.280 2.309 2.327 2.359 2.359 2.359 2.374 2.374 2.372 2.374 2.435 2.434 2.434 2.489 2.500 2.500 2.500 2.497 2.510 2.556 2.556 2.560 2.595 2.618 2.625 2.622 2.625 2.621 2.670
Maximum Inches
1.878 1.878 1.878 1.878 1.893 1.915 1.940 1.940 1.971 1.983 2.003 2.003 2.003 2.003 2.047 2.063 2.130 2.128 2.130 2.169 2.168 2.192 2.205 2.233 2.233 2.233 2.243 2.255 2.255 2.255 2.255 2.286 2.315 2.333 2.365 2.365 2.365 2.380 2.380 2.378 2.380 2.441 2.440 2.441 2.495 2.506 2.506 2.506 2.503 2.516 2.562 2.562 2.566 2.601 2.624 2.631 2.628 2.631 2.627 2.677
* Indicates Speedi-Sleeve Gold product
10
"Z" Installation depth
1.050 1.000 0.744 0.744 0.984 1.000 1.000 1.000 0.984 1.050 1.006 1.000 1.000 1.000 1.359 1.375 1.375 1.281 1.375 1.250 1.250 1.313 1.313 1.313 1.313 1.250 1.250 1.313 1.313 1.313 1.313 1.375 1.375 1.500 1.375 1.375 1.471 1.375 1.375 1.375 1.375 1.425 1.393 1.425 1.393 1.375 1.393 1.375 0.890 1.438 1.375 1.375 1.375 1.250 1.375 1.375 1.375 1.375 1.375 1.688
Speedi-Sleeve size listing - Inches (Cont.)
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99268 99273 99843 * 99844 * 99267 99269 99272 99274 99275 99276 99281 99870 * 99284 99845 * 99282 99286 99846 * 99287 99847 * 99290 99293 99875 * 99289 99294 99292 99291 99298 99299 99848 * 99296 99300 99303 99301 99306 99849 * 99307 99311 99312 99313 99315 99317 99328 99850 * 99851 * 99322 99324 99325 99326 99331 99332 99333 99872 * 99334 99337 99338 99339 99340 99852 * 99346 99347
0.781 0.781 0.781 0.781 1.438 1.125 0.406 0.781 0.781 0.787 0.594 0.750 0.750 0.500 0.500 0.781 0.781 0.781 0.781 0.500 0.781 0.866 0.594 0.866 0.813 0.484 0.563 0.813 0.813 0.813 0.813 0.625 0.500 0.750 0.813 0.551 0.688 0.813 0.750 0.827 0.433 0.660 0.595 0.813 0.813 0.595 0.813 0.688 0.813 0.669 0.827 0.827 0.399 0.813 0.375 0.781 0.781 0.813 0.625 0.313
0.906 0.938 0.938 0.938 1.625 1.250 0.563 0.938 0.938 0.945 0.688 0.875 0.875 0.656 0.656 0.938 0.938 0.938 0.938 0.641 0.938 1.024 0.690 1.024 1.000 0.625 0.688 1.000 1.000 0.938 1.000 0.813 0.625 0.875 1.000 0.709 0.813 1.000 0.886 0.945 0.591 0.848 0.719 1.000 1.000 0.719 1.000 0.875 1.000 0.827 0.984 0.984 0.499 1.000 0.500 0.906 0.906 1.000 0.813 0.500
3.125 3.065 3.125 3.125 3.075 3.125 3.125 3.125 3.125 3.125 3.188 3.225 3.225 3.225 3.225 3.188 3.219 3.219 3.344 3.344 3.344 3.305 3.273 3.305 3.235 3.359 3.359 3.350 3.235 3.240 3.235 3.345 3.355 3.468 3.531 3.525 3.531 3.531 3.540 3.543 3.543 3.585 3.575 3.585 3.594 3.575 3.585 3.585 3.688 3.700 3.700 3.700 3.580 3.695 3.688 3.844 3.835 3.844 3.844 3.825
"A" Shaft diameter range Nominal shaft diameter
2.730 2.743 2.750 2.750 2.750 2.750 2.750 2.750 2.750 2.756 2.813 2.835 2.835 2.838 2.838 2.869 2.875 2.875 2.938 2.938 2.940 2.953 2.953 2.953 2.974 2.993 2.993 2.993 3.000 3.000 3.000 3.000 3.011 3.071 3.125 3.125 3.125 3.125 3.150 3.150 3.150 3.228 3.250 3.250 3.250 3.250 3.250 3.250 3.310 3.342 3.342 3.346 3.346 3.375 3.375 3.438 3.480 3.500 3.500 3.500
Minimum Inches
Maximum Inches
2.727 2.740 2.745 2.750 2.747 2.750 2.750 2.745 2.750 2.753 2.809 2.827 2.828 2.838 2.838 2.866 2.873 2.873 2.937 2.937 2.937 2.950 2.950 2.950 2.972 2.990 2.990 2.990 3.000 2.997 3.000 3.000 3.008 3.064 3.120 3.124 3.120 3.120 3.142 3.146 3.146 3.225 3.250 3.250 3.247 3.250 3.250 3.250 3.307 3.337 3.337 3.337 3.338 3.373 3.373 3.435 3.477 3.500 3.497 3.500
2.733 2.746 2.751 2.756 2.753 2.756 2.756 2.751 2.756 2.759 2.815 2.835 2.835 2.844 2.844 2.872 2.879 2.879 2.943 2.943 2.943 2.956 2.956 2.956 2.976 2.996 2.996 2.996 3.006 3.003 3.006 3.006 3.014 3.071 3.126 3.132 3.126 3.126 3.150 3.153 3.153 3.231 3.256 3.256 3.253 3.256 3.256 3.256 3.313 3.347 3.347 3.347 3.346 3.379 3.379 3.441 3.483 3.506 3.503 3.506
"Z" Installation depth
1.313 1.250 1.250 1.250 1.625 1.312 1.250 1.250 1.250 1.250 1.250 1.343 1.343 1.250 1.250 1.250 1.250 1.250 1.313 1.331 1.313 1.313 1.083 1.313 1.250 1.331 1.375 1.281 1.281 1.375 1.281 1.280 2.000 2.056 2.000 2.031 2.000 2.000 1.375 1.375 1.375 1.750 1.375 1.375 1.375 1.375 1.375 1.250 1.375 1.378 1.378 1.378 1.431 1.375 1.410 1.406 1.406 1.347 1.347 1.347
* Indicates Speedi-Sleeve Gold product
11
Speedi-Sleeve size listing - Inches (Cont.)
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99350 99349 99351 99352 99353 99354 99356 99360 99362 99363 99365 99368 99359 99366 99369 99364 99374 99376 99853 * 99367 99372 99386 99387 99854 * 99393 99855 * 99395 99399 99400 99401 99409 99412 99413 99418 99423 99424 99435 99434 99437 99438 99439 99856 * 99450 99452 99463 99465 99468 99471 99473 99475 99472 99484 99487 99490 99492 99857 * 99858 * 99498 99499 99501
0.813 0.625 0.710 0.438 0.526 0.906 0.813 0.813 0.813 0.500 0.813 0.313 0.469 0.781 0.827 0.469 0.344 0.563 0.688 0.344 0.688 0.813 0.813 0.813 0.813 0.813 0.600 0.813 0.650 0.500 0.787 0.813 0.787 0.813 0.781 0.813 0.509 0.448 0.813 0.750 1.000 0.813 0.813 0.813 1.000 0.438 0.813 0.315 0.787 0.500 0.787 0.787 0.625 0.394 1.024 0.688 0.813 0.688 0.813 0.540
1.000 0.813 0.906 0.538 0.667 1.102 1.000 1.000 1.000 0.625 0.938 0.438 0.594 0.906 0.945 0.594 0.500 0.688 0.875 0.500 0.875 1.000 1.000 1.000 1.000 1.000 0.725 1.000 0.775 0.625 0.945 1.000 0.913 1.000 0.906 1.000 0.650 0.589 1.000 0.886 1.142 1.000 1.000 0.938 1.250 0.625 1.000 0.433 0.984 0.750 0.945 0.984 0.750 0.551 1.260 0.875 1.000 0.875 1.000 0.681
3.844 3.844 4.000 4.000 4.000 4.000 3.900 4.031 4.031 4.025 4.025 4.031 4.016 4.025 4.025 4.035 4.031 4.025 4.020 4.025 4.020 4.185 4.219 4.313 4.313 4.375 4.375 4.375 4.375 4.375 4.438 4.470 4.470 4.500 4.610 4.610 4.921 4.921 4.750 4.750 4.813 4.900 4.850 5.000 5.063 5.000 5.063 5.110 5.110 5.000 5.177 5.229 5.250 5.400 5.400 5.400 5.390 5.400 5.390 5.400
"A" Shaft diameter range Nominal shaft diameter
3.500 3.504 3.543 3.543 3.543 3.543 3.563 3.621 3.625 3.625 3.688 3.688 3.730 3.730 3.740 3.743 3.743 3.749 3.750 3.753 3.753 3.871 3.875 3.938 3.938 4.000 4.000 4.000 4.000 4.000 4.094 4.125 4.134 4.188 4.234 4.250 4.328 4.331 4.375 4.409 4.438 4.500 4.500 4.528 4.625 4.625 4.688 4.724 4.724 4.750 4.803 4.843 4.875 4.921 4.921 5.000 5.000 5.000 5.000 5.000
Minimum Inches
3.500 3.501 3.540 3.540 3.540 3.540 3.560 3.618 3.623 3.623 3.685 3.684 3.727 3.727 3.737 3.740 3.740 3.746 3.750 3.750 3.750 3.868 3.873 3.935 3.935 3.998 3.998 3.998 3.998 3.998 4.090 4.122 4.130 4.183 4.226 4.248 4.327 4.322 4.370 4.401 4.434 4.496 4.496 4.523 4.621 4.621 4.685 4.720 4.720 4.746 4.799 4.839 4.871 4.917 4.917 4.998 4.998 4.998 4.998 4.998
Maximum Inches
3.506 3.507 3.546 3.546 3.546 3.546 3.566 3.624 3.629 3.629 3.691 3.690 3.733 3.733 3.743 3.746 3.746 3.752 3.756 3.756 3.756 3.874 3.879 3.941 3.941 4.006 4.006 4.006 4.006 4.006 4.098 4.130 4.138 4.191 4.234 4.256 4.335 4.331 4.378 4.409 4.442 4.504 4.504 4.531 4.629 4.629 4.693 4.728 4.728 4.754 4.807 4.847 4.879 4.925 4.925 5.006 5.006 5.006 5.006 5.006
* Indicates Speedi-Sleeve Gold product
12
"Z" Installation depth
1.347 1.348 1.813 1.813 1.750 1.750 1.750 1.750 1.750 1.750 1.800 0.875 1.800 1.800 1.800 1.800 1.800 1.800 1.800 1.800 1.800 1.875 1.875 2.050 2.050 2.050 2.050 2.050 1.375 2.066 1.417 1.375 1.378 1.375 1.438 1.438 1.250 1.297 1.650 1.300 1.313 1.250 1.250 1.250 1.375 1.375 1.375 1.323 1.260 1.500 1.260 1.244 1.438 1.438 1.438 1.438 1.438 1.438 1.438 1.438
Speedi-Sleeve size listing - Inches (Cont.)
Stock number
"X" Width on shaft (Inches ± .031)
"Y" Overall width (Inches ± .031)
"D" Flange diameter (Inches ± .063)
99494 99874 * 99491 99513 99525 99533 99537 99548 99547 99859 * 99549 99550 99552 99560 99571 99562 99575 99862 * 99587 99595 99596 99599 99601 99605 99606 99620 99625 99630 99650 99640 99675 99687 99864 * 99700 99721 99725 99726 99745 99750 99775 99787 99799 99800
0.750 0.866 0.866 0.813 0.813 0.807 0.813 1.500 0.563 0.813 0.813 0.518 0.807 0.875 0.750 0.563 0.813 1.000 1.000 1.024 1.000 1.000 0.500 1.024 1.024 0.813 1.031 1.000 1.000 1.250 0.813 1.102 1.000 1.000 1.299 1.250 1.260 0.813 0.813 1.000 1.359 1.000 1.000
0.938 0.996 0.996 1.000 1.000 1.000 1.000 1.688 0.750 1.000 1.000 0.705 1.000 1.000 0.875 0.750 1.000 1.250 1.250 1.181 1.125 1.250 0.750 1.181 1.181 1.063 1.250 1.250 1.250 1.496 1.063 1.260 1.250 1.250 1.496 1.500 1.496 1.000 1.000 1.313 1.500 1.250 1.250
5.493 5.493 5.493 5.500 5.560 5.735 5.875 5.750 5.900 5.938 5.938 5.938 5.945 6.188 6.100 6.100 6.180 6.188 6.188 6.260 6.375 6.375 6.360 6.375 6.575 6.625 6.625 6.750 7.000 7.188 7.125 7.362 7.475 7.475 7.500 7.760 7.760 7.860 7.875 8.270 8.375 8.375 8.375
"A" Shaft diameter range Nominal shaft diameter
5.114 5.118 5.125 5.125 5.250 5.311 5.375 5.438 5.476 5.500 5.500 5.500 5.512 5.625 5.709 5.734 5.750 5.875 5.875 5.905 5.938 6.000 6.000 6.063 6.097 6.203 6.250 6.299 6.500 6.688 6.750 6.890 7.000 7.000 7.087 7.250 7.278 7.453 7.500 7.750 7.875 7.938 8.000
Minimum Inches
Maximum Inches
5.110 5.117 5.117 5.120 5.246 5.307 5.371 5.434 5.472 5.498 5.498 5.498 5.508 5.621 5.699 5.726 5.746 5.871 5.871 5.896 5.934 5.995 5.995 6.058 6.092 6.198 6.245 6.289 6.495 6.683 6.745 6.880 6.995 6.995 7.077 7.244 7.273 7.444 7.495 7.745 7.869 7.933 7.995
5.118 5.125 5.125 5.128 5.254 5.315 5.379 5.442 5.480 5.506 5.506 5.506 5.516 5.629 5.709 5.734 5.754 5.879 5.879 5.906 5.942 6.003 6.003 6.068 6.102 6.208 6.255 6.299 6.505 6.693 6.755 6.890 7.005 7.005 7.087 7.254 7.283 7.454 7.505 7.755 7.879 7.943 8.005
"Z" Installation depth
1.181 1.280 1.280 1.250 1.250 1.250 1.250 1.875 1.234 1.250 1.250 1.250 1.250 1.812 1.812 1.938 1.750 1.313 1.313 1.280 1.875 1.750 1.750 1.299 1.299 1.750 1.750 1.375 1.375 1.750 1.750 1.378 1.688 1.688 1.752 2.175 2.165 1.250 1.250 1.875 1.750 1.750 1.750
* Indicates Speedi-Sleeve Gold product
13
Speedi-Sleeve size listing - Metric Nominal Shaft diameter
12.00 12.70 14.00 14.30 15.00 15.88 15.88 16.00 17.00 17.37 18.00 19.00 19.00 19.30 19.86 20.00 20.65 21.82 22.00 22.00 22.23 22.23 23.11 23.11 24.00 24.59 24.59 25.00 25.00 25.40 25.40 26.00 27.00 27.00 27.66 28.00 28.00 28.58 28.58 28.58 29.36 29.36 29.85 30.00 30.15 31.00 31.50 31.75 31.75 31.75 32.00 33.00 33.30 33.35 33.35 34.00 34.90 34.90 34.92 35.00
"A" Shaft diameter range Minimum MM
11.91 12.65 13.89 14.22 14.96 15.82 15.83 15.89 16.94 17.32 17.87 19.00 19.00 19.27 19.81 19.94 20.62 21.77 21.87 21.87 22.17 22.18 23.06 23.06 23.87 24.54 24.54 24.94 24.94 25.35 25.35 25.88 26.92 26.92 27.61 27.94 27.94 28.52 28.53 28.53 29.31 29.31 29.80 29.95 30.10 30.88 31.42 31.67 31.67 31.67 31.92 32.94 33.22 33.27 33.27 33.86 34.82 34.82 34.82 34.92
Maximum MM
12.07 12.75 14.00 14.38 15.06 15.93 15.93 16.00 17.04 17.42 18.00 19.10 19.10 19.33 19.91 20.04 20.70 21.87 22.00 22.00 22.28 22.28 23.16 23.17 24.00 24.64 24.64 25.04 25.04 25.45 25.45 26.01 27.03 27.02 27.71 28.04 28.04 28.63 28.63 28.63 29.41 29.41 29.93 30.08 30.23 31.04 31.58 31.83 31.83 31.83 32.08 33.04 33.38 33.43 33.43 34.01 34.98 34.98 34.98 35.08
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation depth
Stock
on shaft
width
diameter
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
6.00 6.35 6.35 6.35 5.00 7.95 7.95 7.95 7.95 7.95 8.00 7.95 7.95 7.95 7.95 8.00 9.52 6.35 6.58 8.00 7.95 7.95 7.95 7.95 7.95 7.95 15.88 7.95 7.95 7.95 7.95 8.00 7.95 7.95 7.95 9.52 9.52 7.95 7.95 9.52 9.52 9.52 7.95 8.00 7.95 7.95 8.00 7.95 15.88 7.95 8.00 15.01 6.35 12.70 12.70 12.70 7.95 12.70 12.70 13.01
8.40 9.93 9.93 9.93 8.99 10.31 10.31 11.10 11.00 11.13 11.00 11.13 11.13 11.13 11.13 11.00 14.30 9.52 9.09 11.99 11.13 11.13 11.13 11.13 11.10 11.13 18.26 11.00 11.00 11.13 11.13 11.99 11.13 11.13 11.13 12.70 12.70 11.13 11.13 12.70 12.70 12.70 11.13 11.00 11.13 11.00 11.10 11.13 19.05 11.13 11.13 18.00 9.50 15.90 15.88 15.90 11.13 15.88 15.88 16.00
15.50 19.05 19.05 19.05 19.05 19.05 19.05 18.24 22.23 22.86 24.43 24.00 24.00 23.83 23.75 23.62 0.00 29.34 30.20 30.17 27.79 27.79 30.94 30.94 28.70 28.70 28.70 33.02 33.02 30.96 30.96 33.35 33.53 33.53 35.71 34.92 34.92 38.10 38.10 38.10 34.29 34.29 35.56 35.56 35.56 39.70 39.12 38.10 38.10 38.10 38.10 40.49 40.64 40.49 40.49 41.28 41.60 41.60 41.60 41.60
47.60 46.51 46.51 46.51 47.29 50.80 50.80 50.80 50.80 50.80 46.00 50.80 50.80 50.80 50.80 50.80 76.20 50.80 47.09 46.05 50.80 50.80 46.91 46.91 50.80 50.80 50.80 50.80 50.80 50.80 50.80 46.05 46.81 46.81 15.88 46.81 46.81 17.48 17.48 17.48 17.48 17.48 17.48 17.48 17.48 15.88 17.48 17.48 50.80 17.48 17.48 20.65 20.65 20.65 20.65 20.70 20.65 20.65 20.65 20.65
99049 99050 99055 99056 99059 99810 * 99062 99058 99068 99060 99082 99811 * 99076 99081 99080 99078 99083 99086 99084 99085 99812 * 99087 99091 99860 * 99092 99094 99096 99813 * 99098 99814 * 99100 99103 99815 * 99106 99108 99866 * 99111 99816 * 99112 99116 99120 99865 * 99122 99114 99118 99123 99141 99817 * 99871 * 99125 99128 99121 99129 99818 * 99131 99134 99133 99138 99819 * 99820 *
* Indicates Speedi-Sleeve Gold product
14
Speedi-Sleeve size listing - Metric (Cont.) Nominal Shaft diameter
35.00 36.00 36.45 36.53 36.53 38.00 38.10 38.10 38.10 38.10 38.68 39.42 39.67 39.70 39.85 40.00 40.00 40.00 40.77 41.00 41.28 41.28 41.28 42.00 42.00 42.00 42.06 42.85 42.88 43.00 43.64 44.17 44.45 44.45 44.45 44.45 44.45 44.45 44.81 44.86 45.00 45.00 45.24 46.05 46.05 47.24 47.45 47.63 47.63 47.63 47.63 47.63 48.00 48.56 49.20 49.22 50.00 50.30 50.80 50.80
"A" Shaft diameter range Minimum MM
34.92 35.85 36.37 36.37 36.45 37.85 38.02 38.02 38.02 38.02 38.60 39.34 39.59 39.60 39.77 39.93 39.84 39.93 40.69 40.84 41.20 41.20 41.20 41.84 41.84 41.84 41.98 42.78 42.80 42.84 43.56 44.09 44.37 44.37 44.37 44.37 44.37 44.37 44.73 44.73 44.93 44.93 45.16 45.95 45.94 47.16 47.39 47.55 47.55 47.55 47.55 47.55 47.93 48.48 49.12 49.12 49.91 50.21 50.72 50.72
Maximum MM
35.08 36.00 36.53 36.53 36.61 38.00 38.18 38.18 38.18 38.18 38.76 39.50 39.75 39.75 39.93 40.08 40.00 40.09 40.85 41.00 41.35 41.36 41.36 42.00 42.00 42.00 42.14 42.93 42.96 43.00 43.72 44.25 44.53 44.53 44.53 44.53 44.53 44.53 44.89 44.88 45.08 45.09 45.32 46.10 46.10 47.32 47.55 47.70 47.71 47.71 47.71 47.71 48.09 48.64 49.28 49.28 50.07 50.37 50.88 50.88
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation depth
Stock
on shaft
width
diameter
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
13.01 13.01 14.30 14.30 9.52 13.01 14.30 9.52 14.30 9.52 11.13 11.13 14.30 14.30 15.88 13.01 9.91 13.01 12.70 12.70 14.30 7.95 14.30 14.00 11.30 14.30 13.97 14.30 7.95 12.70 14.30 9.52 14.30 19.05 9.52 14.30 19.05 13.49 13.99 14.30 16.87 13.99 14.30 14.30 14.30 22.58 22.58 14.30 9.53 14.30 7.49 4.45 14.00 9.53 14.30 14.30 14.00 14.30 14.30 22.23
16.00 16.99 17.48 17.48 12.70 16.99 17.48 12.70 17.48 12.70 14.30 14.30 17.48 17.48 19.05 16.00 12.93 16.00 16.28 15.88 17.48 11.13 17.48 18.00 14.50 17.50 17.50 17.48 11.13 15.88 17.48 12.70 17.48 22.23 12.70 17.48 22.23 15.88 16.99 17.48 20.32 16.99 17.48 17.48 17.48 17.48 26.03 17.48 13.11 17.48 10.54 7.49 16.97 12.70 17.48 17.48 17.00 17.88 17.48 25.40
41.60 45.24 45.24 45.24 45.24 45.24 45.24 45.24 45.24 45.24 47.22 47.22 47.22 47.22 47.22 46.99 46.99 46.99 49.22 49.20 47.63 47.63 47.63 53.01 53.01 53.01 53.01 48.41 48.41 48.41 51.59 52.40 52.40 52.40 52.20 52.40 52.40 52.40 53.01 52.40 53.97 53.01 53.09 54.76 53.09 55.58 55.95 55.96 55.96 55.96 55.96 55.96 56.01 56.36 56.36 56.36 57.00 58.75 61.11 61.11
20.65 24.99 25.81 25.81 25.81 24.99 25.81 25.81 25.81 25.81 25.81 25.81 25.81 25.81 25.81 25.98 25.40 25.98 25.40 25.81 20.65 25.81 20.65 21.01 21.49 21.01 21.01 22.23 22.23 21.41 20.65 20.65 20.65 20.65 20.65 20.65 20.65 22.23 20.65 20.65 26.98 20.63 25.40 25.40 25.40 25.40 25.40 25.40 26.67 25.40 18.90 18.90 24.99 25.40 25.40 25.40 24.99 26.67 25.40 25.40
99139 99146 99143 99821 * 99144 99147 99822 * 99823 * 99149 99150 99152 99155 99156 99824 * 99159 99825 * 99153 99157 99160 99163 99826 * 99161 99162 99873 * 99166 99169 99165 99168 99167 99182 99171 99170 99827 * 99828 * 99172 99174 99175 99180 99176 99829 * 99830 * 99177 99179 99831 * 99181 99185 99186 99832 * 99184 99187 99188 99190 99189 99192 99193 99833 * 99196 99198 99834 * 99835 *
* Indicates Speedi-Sleeve Gold product
15
Speedi-Sleeve size listing - Metric (Cont.) Nominal
"A" Shaft diameter range
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation
Shaft
Minimum
Maximum
Stock
on shaft
width
diameter
depth
diameter
MM
MM
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
14.30 22.23 12.70 19.84 19.84 12.70 19.84 19.99 19.99 19.84 12.70 12.70 19.84 12.70 19.41 19.84 7.95 19.84 7.95 19.84 19.84 19.05 20.00 20.00 9.40 19.84 15.09 19.84 13.36 19.84 12.70 12.70 19.84 19.84 12.70 19.84 14.10 19.84 20.00 19.99 19.84 19.84 19.84 19.84 19.84 12.70 19.84 19.05 19.84 19.84 19.84 19.84 36.53 19.84 28.58 10.31 19.84 19.99 15.09 19.05
17.48 25.40 15.88 23.83 23.83 19.05 23.83 22.99 22.99 23.83 15.88 15.88 23.01 15.88 22.86 23.83 11.13 23.83 11.13 23.83 23.83 22.23 23.00 23.00 11.43 23.83 19.05 23.83 17.35 23.83 15.88 15.88 23.83 23.83 16.66 23.83 16.51 23.01 23.00 22.99 23.83 23.83 23.83 23.01 23.83 15.88 23.83 22.23 23.01 23.83 23.83 23.83 41.28 23.83 31.75 14.30 23.83 24.00 17.48 22.23
61.11 61.11 62.71 62.71 61.52 61.52 61.52 62.00 62.00 63.50 64.29 64.29 64.29 64.29 65.10 64.29 64.29 64.29 64.29 65.99 68.28 69.85 70.74 70.74 70.74 69.85 69.85 69.85 69.85 71.83 71.83 71.83 73.03 71.63 71.83 71.63 71.63 71.83 72.39 72.39 73.43 75.95 77.39 77.39 77.39 77.39 77.39 79.38 79.38 77.85 79.38 79.38 78.11 79.38 79.38 79.38 79.38 79.38 80.98 81.92
25.40 25.40 34.52 34.93 34.92 32.54 34.93 31.75 31.75 33.35 33.35 33.35 31.75 33.35 31.75 33.35 33.35 33.35 33.35 34.92 34.93 38.10 34.93 34.93 37.36 34.92 34.93 34.93 34.93 35.38 36.20 36.20 35.38 34.92 35.38 34.93 22.61 36.53 34.92 34.93 34.93 31.75 34.93 34.93 34.92 34.93 34.93 42.88 33.35 31.75 31.75 31.75 41.28 31.75 33.32 31.75 31.75 31.75 31.75 34.11
50.80 50.80 52.00 52.32 54.00 54.00 54.00 54.99 55.00 55.60 56.00 56.64 56.64 56.64 56.90 57.15 57.15 57.20 57.20 58.00 58.72 59.18 60.00 60.00 60.00 60.33 60.33 60.38 60.38 61.90 62.00 62.00 63.30 63.50 63.50 63.50 63.50 63.83 65.00 65.00 65.10 66.00 66.57 66.65 66.68 66.68 66.75 68.00 69.34 69.67 69.80 69.85 69.85 70.00 70.00 70.00 70.00 70.00 71.42 72.00
50.72 50.72 51.81 52.24 53.95 53.92 53.95 54.92 54.91 55.52 55.81 56.56 56.56 56.57 56.82 57.13 57.13 57.12 57.12 57.91 58.64 59.10 59.91 59.91 59.92 60.30 60.25 60.30 60.30 61.82 61.85 61.81 63.22 63.50 63.50 63.50 63.42 63.75 64.92 64.92 65.02 65.91 66.49 66.57 66.68 66.60 66.67 67.81 69.26 69.59 69.72 69.72 69.77 69.85 69.85 69.85 69.85 69.92 71.34 71.81
50.88 50.88 52.00 52.40 54.10 54.06 54.11 55.09 55.07 55.68 56.00 56.72 56.72 56.72 56.98 57.28 57.28 57.28 57.28 58.06 58.80 59.26 60.07 60.07 60.08 60.45 60.41 60.46 60.46 61.98 62.01 62.00 63.38 63.65 63.66 63.66 63.58 63.91 65.07 65.08 65.18 66.07 66.65 66.73 66.83 66.76 66.83 68.00 69.42 69.75 69.88 69.88 69.93 70.00 70.01 70.01 70.01 70.08 71.50 72.01
99199 99200 99204 99205 99836 * 99210 99212 99863 * 99215 99218 99220 99229 99230 99861 * 99226 99837 * 99838 * 99225 99227 99219 99231 99233 99869 * 99235 99241 99839 * 99238 99237 99240 99243 99242 99244 99249 99840 * 99248 99250 99253 99251 99841 * 99254 99256 99259 99261 99264 99842 * 99260 99262 99266 99268 99273 99274 99843 * 99267 99844 * 99269 99272 99275 99276 99281 99870 *
* Indicates Speedi-Sleeve Gold product
16
Speedi-Sleeve size listing - Metric (Cont.) Nominal Shaft diameter
72.00 72.08 72.16 72.87 73.00 73.00 74.63 74.68 74.68 75.00 75.00 75.00 75.54 76.00 76.00 76.02 76.20 76.20 76.28 76.28 76.48 78.00 79.32 79.38 79.38 79.38 80.00 80.00 80.00 82.00 82.50 82.55 82.55 82.63 82.63 82.63 84.00 85.00 85.00 85.00 85.00 85.75 85.75 87.33 88.39 88.98 89.00 89.00 89.00 89.00 90.00 90.00 90.00 90.00 90.50 92.00 92.10 92.10 93.65 93.68
"A" Shaft diameter range Minimum MM
71.81 72.08 72.08 72.79 72.97 72.97 74.60 74.60 74.60 74.93 74.93 74.93 75.49 75.94 75.94 75.94 76.20 76.12 76.20 76.20 76.40 77.81 79.24 79.25 79.24 79.35 79.81 79.91 79.90 81.91 82.50 82.55 82.47 82.55 82.55 82.55 84.00 84.76 84.76 84.76 84.78 85.67 85.67 87.25 88.31 88.82 88.90 88.90 88.92 88.90 89.91 89.91 89.91 89.91 90.42 91.89 92.02 92.02 93.57 93.60
Maximum MM
72.00 72.24 72.24 72.95 73.13 73.13 74.75 74.76 74.75 75.09 75.09 75.09 75.59 76.10 76.10 76.10 76.35 76.28 76.36 76.36 76.56 78.00 79.40 79.40 79.40 79.55 80.01 80.08 80.08 82.07 82.70 82.70 82.63 82.71 82.71 82.71 84.15 85.02 85.02 85.02 85.00 85.83 85.83 87.41 88.47 88.98 89.05 89.06 89.08 89.06 90.07 90.07 90.07 90.07 90.58 92.05 92.18 92.18 93.73 93.76
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation depth
Stock
on shaft
width
diameter
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
19.05 12.70 12.70 19.84 19.84 19.84 19.84 12.70 19.84 22.00 15.09 22.00 20.62 14.30 20.65 12.29 20.65 20.65 20.65 15.88 12.70 19.05 17.48 20.65 20.65 14.00 19.05 21.01 11.00 16.76 15.11 20.65 20.65 15.11 20.65 17.48 20.65 21.00 16.99 21.01 10.13 20.65 9.53 19.84 19.84 15.88 20.65 7.95 15.88 20.65 18.03 11.13 13.36 23.01 20.65 20.65 20.65 12.70 7.95 20.65
22.23 16.66 16.66 23.83 23.83 23.83 23.83 16.28 23.83 26.01 17.53 26.01 25.40 17.48 25.40 15.88 25.40 23.83 25.40 20.65 15.88 22.23 20.65 25.40 25.40 18.01 22.50 24.00 15.01 21.54 18.26 25.40 25.40 18.26 25.40 22.23 25.40 25.00 21.00 24.99 12.67 25.40 12.70 23.01 23.01 20.65 25.40 12.70 20.65 25.40 23.01 13.67 16.94 27.99 25.40 25.40 25.40 15.87 11.13 23.83
81.92 81.92 81.92 80.98 81.76 81.76 84.94 84.94 84.94 83.95 83.13 83.95 82.17 85.32 85.09 85.32 82.17 82.30 82.17 84.96 85.22 88.04 89.69 89.69 89.69 89.54 89.92 89.99 89.99 91.06 90.81 91.06 91.29 90.81 91.06 91.06 93.68 93.98 93.98 93.98 90.93 93.85 93.67 97.64 97.41 97.64 97.64 97.16 97.64 97.64 101.60 101.60 101.60 101.60 99.06 102.39 102.39 102.24 102.39 102.24
34.11 31.75 31.75 31.75 31.75 31.75 33.35 33.81 33.35 33.35 27.51 33.35 31.75 34.93 32.54 33.81 32.54 34.93 32.54 32.51 50.80 52.22 50.80 50.80 50.80 51.59 34.93 34.93 34.93 44.45 34.92 34.92 34.93 34.93 34.93 31.75 34.93 35.00 35.00 35.00 36.35 34.93 35.81 35.71 35.71 34.21 34.21 34.21 34.24 34.21 46.05 46.05 44.45 44.45 44.45 44.45 44.45 44.45 22.23 45.72
99284 99845 * 99282 99286 99846 * 99287 99847 * 99290 99293 99875 * 99289 99294 99292 99298 99299 99291 99848 * 99296 99300 99303 99301 99306 99311 99849 * 99312 99307 99313 99315 99317 99328 99850 * 99851 * 99322 99324 99325 99326 99331 99872 * 99332 99333 99334 99337 99338 99339 99340 99346 99852 * 99347 99349 99350 99351 99352 99353 99354 99356 99360 99362 99363 99368 99365
* Indicates Speedi-Sleeve Gold product
17
Speedi-Sleeve size listing - Metric (Cont.) Nominal
"A" Shaft diameter range
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation
Shaft
Minimum
Maximum
Stock
on shaft
width
diameter
depth
diameter
MM
MM
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
11.91 19.84 11.91 21.01 8.74 14.30 17.48 8.74 17.48 20.65 20.65 20.65 20.65 20.65 15.24 20.65 16.51 12.70 19.99 20.65 19.99 20.65 19.84 20.65 11.38 12.93 20.65 19.05 25.40 20.65 20.65 20.65 25.40 11.13 20.65 8.00 19.99 12.70 19.99 19.99 15.88 10.00 26.01 17.48 20.65 17.48 20.65 13.72 22.00 22.00 19.05 20.65 20.65 20.50 20.65 38.10 14.30 20.65 20.65 13.16
15.09 23.01 15.09 24.00 12.70 17.48 22.23 12.70 22.23 25.40 25.40 25.40 25.40 25.40 18.42 25.40 19.69 15.88 24.00 25.40 23.19 25.40 23.01 25.40 14.96 16.51 25.40 22.50 29.01 25.40 25.40 23.83 31.75 15.88 25.40 11.00 24.99 19.05 24.00 24.99 19.05 14.00 32.00 22.23 25.40 22.23 25.40 17.30 25.30 25.30 23.83 25.40 25.40 25.40 25.40 42.88 19.05 25.40 25.40 17.91
102.01 102.24 102.49 102.24 102.39 102.24 102.11 102.24 102.11 106.30 107.16 109.55 109.55 111.13 111.13 111.13 111.13 111.13 112.72 113.54 113.54 114.30 117.09 117.09 124.99 124.99 120.65 120.70 122.25 124.46 123.19 127.00 128.60 127.00 128.60 129.79 129.79 127.00 131.49 132.82 133.35 137.16 137.16 137.16 139.91 137.16 136.91 137.16 139.52 139.52 139.52 139.70 141.22 145.67 149.23 146.05 149.86 150.82 150.83 150.83
45.72 45.72 45.72 45.72 45.72 45.72 45.72 45.72 45.72 47.63 47.63 52.07 52.07 52.07 52.07 52.07 34.93 52.48 35.99 34.93 35.00 34.93 36.53 36.53 32.94 31.75 41.91 33.02 33.35 31.75 31.75 31.75 34.93 34.93 34.93 33.60 32.00 38.10 32.00 31.60 36.53 36.53 36.53 36.53 36.53 36.50 36.53 36.53 32.51 32.51 30.00 31.75 31.75 31.75 31.75 47.63 31.34 31.75 31.75 31.75
94.74 94.74 95.00 95.00 95.00 95.22 95.25 95.33 95.33 98.32 98.45 100.00 100.00 101.60 101.65 101.65 101.65 101.65 104.00 104.80 105.00 106.35 107.44 108.00 110.00 110.00 111.10 112.00 112.72 114.30 114.30 115.00 117.48 117.48 119.00 120.00 120.00 120.65 122.00 123.00 123.83 125.00 125.00 127.00 127.00 127.00 127.00 127.00 130.00 130.00 130.00 130.15 133.35 135.00 136.53 138.13 139.00 139.70 139.75 139.75
94.66 94.66 94.99 94.92 94.99 95.14 95.25 95.25 95.25 98.24 98.37 99.95 99.95 101.55 101.55 101.55 101.55 101.55 103.89 104.70 104.90 106.25 107.34 107.90 109.78 109.91 111.00 111.78 112.63 114.20 114.20 114.89 117.38 117.38 119.00 119.89 119.89 120.55 121.90 122.91 123.73 124.90 124.89 126.95 126.95 126.95 126.95 126.95 129.97 129.97 129.80 130.05 133.25 134.80 136.43 138.03 138.99 139.65 139.65 139.65
94.82 94.82 95.15 95.08 95.15 95.30 95.40 95.41 95.41 98.40 98.53 100.10 100.11 101.75 101.75 101.75 101.75 101.75 104.09 104.90 105.10 106.45 107.54 108.10 110.00 110.11 111.20 112.00 112.83 114.40 114.40 115.09 117.58 117.58 119.20 120.09 120.09 120.75 122.10 123.11 123.93 125.10 125.09 127.15 127.15 127.15 127.15 127.15 130.17 130.17 130.00 130.25 133.45 135.00 136.63 138.23 139.19 139.85 139.85 139.85
99359 99366 99364 99369 99374 99376 99853 * 99367 99372 99386 99387 99854 * 99393 99855 * 99395 99399 99400 99401 99409 99412 99413 99418 99423 99424 99434 99435 99437 99438 99439 99856 * 99450 99452 99463 99465 99468 99471 99473 99475 99472 99484 99487 99490 99492 99857 * 99858 * 99498 99499 99501 99874 * 99491 99494 99513 99525 99533 99537 99548 99547 99859 * 99549 99550
* Indicates Speedi-Sleeve Gold product
18
Speedi-Sleeve size listing - Metric (Cont.) "A" Shaft diameter range Shaft diameter
140.00 142.88 145.00 145.54 146.05 149.23 149.23 150.00 150.83 152.37 152.37 154.00 155.00 157.56 158.75 160.00 165.10 170.00 171.45 175.00 177.80 177.80 180.00 184.00 185.00 189.20 190.50 196.85 200.00 201.63 203.20
Minimum MM
139.90 142.77 144.75 145.44 145.95 149.12 149.13 149.75 150.73 152.27 152.27 153.87 154.75 157.43 158.62 159.74 164.97 169.75 171.32 174.75 177.67 177.67 179.75 183.99 184.75 189.07 190.37 196.72 199.87 201.50 203.07
Maximum MM
140.11 142.98 145.00 145.64 146.15 149.33 149.33 150.00 150.93 152.47 152.47 154.13 155.00 157.69 158.88 160.00 165.23 170.01 171.58 175.01 177.93 177.93 180.01 184.25 185.00 189.33 190.63 196.98 200.13 201.76 203.33
"X"
"Y"
"D"
"Z"
Width
Overall
Flange
Installation depth
Stock
on shaft
width
diameter
number
± 0.8 MM
± 0.8 MM
± 1.6 MM
MM
20.50 22.23 19.05 14.30 20.65 25.40 25.40 26.01 25.40 25.40 12.70 26.01 26.01 20.65 26.19 25.40 25.40 31.75 20.65 27.99 25.40 25.40 32.99 31.75 32.00 20.65 20.65 25.40 34.52 25.40 25.40
25.40 25.40 22.23 19.05 25.40 31.75 31.75 30.00 28.58 31.75 19.05 30.00 30.00 27.00 31.75 31.75 31.75 38.00 27.00 32.00 31.75 31.75 38.00 38.10 38.00 25.40 25.40 33.35 38.10 31.75 31.75
151.00 157.18 154.94 154.94 156.97 157.18 157.18 159.00 161.93 161.93 161.54 161.93 167.01 168.28 168.28 171.45 177.80 182.57 180.98 187.00 189.87 189.87 190.50 197.10 197.10 199.64 200.03 210.06 212.73 212.73 212.73
31.75 46.02 46.02 49.23 44.45 33.35 33.35 32.51 47.63 44.45 44.45 32.99 32.99 44.45 44.45 34.93 34.93 44.45 44.45 35.00 42.88 42.88 44.50 55.25 54.99 31.75 31.75 47.63 44.45 44.45 44.45
99552 99560 99571 99562 99575 99862 * 99587 99595 99596 99599 99601 99605 99606 99620 99625 99630 99650 99640 99675 99687 99864 * 99700 99721 99725 99726 99745 99750 99775 99787 99799 99800
* Indicates Speedi-Sleeve Gold product
19
Large diameter wear sleeves for shafts 8.313" to 45" (211.15 – 1143mm)* SKF large diameter wear sleeves Polishing friction and shaft scoring from foreign materials during continued contact between a rotating shaft and a seal make severe shaft damage a common occurrence. Without checking the problem immediately, damage can accelerate sharply. LD wear sleeves are used primarily for applications where no Speedi-Sleeve® is available, i.e. for shafts in the diameter range 8.313" to 45" (203 mm to 1143 mm). Two designs of SKF wear sleeves are available: the Style 3 sleeve with a flange (Figure A) and the Style 4 without a flange (Figure B).
*Primary shaft range. Sleeves for other dimensions and special materials can be evaluated according to specification or the application conditions and quoted upon request.
LDSLV3 is designed with a flange to provide assistance in final positioning of the sleeve. It has a sealing surface width .250" (6.35mm) narrower than the overall sleeve width. The flange adds a nominal 1.000" over the shaft diameter.
There are two alternative ways of using SKF wear sleeves for shaft repairs. Either the sleeve can be positioned on the shaft until it covers the damaged part and a seal which has a .188" (4.8 mm) larger shaft diameter than the original is used, or the shaft can be machined down .188" (4.8 mm) and the original seal size used. The reworked shaft seating for the sleeve should have a surface roughness Ra of between 10-125 micro-inches.
SKF Style Style 3 w/Flg
Shaft Range 8.313" -29" 30" -45"
* Wd Min .688" 1.000"
* Wd Max 2.500" 2.500"
*Overall (1.5" To 2" Max. at 45" Shaft Diameter)
SKF Style Style 4 w/o Flg
Shaft Range 8.313" -29" 30" -45"
* Wd Min .500" .750"
* Wd Max 2.500" 2.500"
*Overall (1.5" To 2" Max. at 45" Shaft Diameter)
Their use is recommended in all cases where the operating conditions for the seals are difficult, particularly where solid contaminants can reach the seal lip, e.g. in rolling mills and chemical plants. These heavy-duty sleeves are used extensively on large diameter shafts in primary metal mills, chemical and mineral processing plants and in power generator applications. In cases where seal wear and damage of the counterface on the shaft can be expected it is recommended that SKF wear sleeves are designed into the application from the outset. During repairs, it will then not be necessary to rework the shaft and the original seal size can always be used as the replacement.
FIGURE A
FIGURE B
Use
Installation
LDSLV4 is the same except without the flange. This version can be made slightly narrower.
20
Each standard sleeve is custom made from high quality SAE 1008 steel. Sleeve hardness is approximately Rockwell B96. Standard wear sleeve thickness is .094” (2.4 mm). The sleeve surface is specially finished to provide a suitable sealing surface for lip seals. A hard chrome plating is applied to provide wear and corrosion resistance.
SKF wear sleeves are mounted with an interference fit on the shaft. It is therefore recommended that they are heated prior to mounting. Temperatures of up to 350°F (177°C) are permitted; under no circumstances should the sleeve be heated to above 400°F (204°C). The types of heating arrangements normally used for bearings are suitable, e.g. heating cabinets, oil baths or induction heaters. The sleeves should be mounted immediately after heating as they cool rapidly and they are difficult to mount cold. This is particularly true of the Style 4 sleeves. Mechanical repositioning of the sleeves by impacts from hammers, etc. should be avoided or minimized.
Removal To remove the sleeve it is recommended first to either heat them or to expand them by light hammer blows. The flange of the Style 3 sleeves should first be cut through at one point. Refer to SKF’s Handbook of Seals (457010) for detailed technical information on large diameter wear sleeves.
®
Speedi-Sleeve and wear sleeve request form Application: (Crankshaft, Pinion, Gearbox Shaft, etc.)___________________________________________________________ _________________________________________________________________________________________________________ Manufacturer, part no. & size of seal being used:______________________________________________________________ _________________________________________________________________________________________________________ My estimated annual quantity would be________sleeve/kits (circle one) Dimensions required: A_____________________
“Z” Length of Installation Required
X_____________________ *Y_____________________
Indicate presence of any keyways or other features***
“A” Z_____________________ Please fill in maximum widths which will fit application. Notes: SPEEDI-SLEEVE® (Ultra-thin .011” wall) for shafts 8.000” or smaller. LARGE DIAMETER SLEEVE (.094” thick wall for shafts 8.313” or larger. Other wall thickness by special quote. Depth for driver tool only for Speedi-Sleeve® size range.) * Flange is standard on Speedi-Sleeve®, optional on LD sleeves over 8.313”. Specify “Y” dimension on large sleeves only if flange is requested.
Shaft Diameter
Show range
(***NOTE: Speedi-Sleeve® must not install over any keyways, splines or ports)
if possible Examples: 2.310/2.315 15.620/15.625
Use Micrometer and measure in unworn area of seal surface
“X” Seal Contact Zone or Width with flange removed
“Y” Overall Width
Business Name___________________________________________________________________________________________ Your Name_______________________________________________________________________________________________ Street Address____________________________________________________________________________________________ City_________________________________________State_______________________Zip Code_________________________ Email________________________________________________Telephone___________________________________________ Please mail completed form to: SKF Sealing Solutions 890 N. State Street, Suite 200 Elgin, IL 60123
Or fax to: Industrial Technical Support 847-742-1085
21
NOTES
22
NOTES
23