Bell Bollard new additions
Bell Bollard installation
TM
TM
The BELL 115 has been designed to allow the installation of a Bell Bollard and a 115mm diameter post or bollard within the same footings. This combination enables the Bell Bollard to still deflect vehicles and protect structures from damage, but where necessary can now act as a high visibility post.
When the BELL 115 is installed with a bollard or post of 1000mm height or greater, the Bell Bollard will conform to disability discrimination guidelines for partially sighted pedestrians.
450mm
G.L.
600mm
The ability of the BELL 115 to act as a pedestrian barrier is further enhanced by incorporating the Bell Bollard into the LINX 100 Railing System. By combining the two products it is possible to design an integrated, cost effective vehicular and pedestrian barrier, with the Bell Bollard protecting any corner post from damage by passing vehicles.
475mm
50mm max protrusion above G.L.
Bell Loop
Diagram B
Kerb Line
800mm
BELL 115 and Linx railing
Diagram A
Parallel to kerb High Visability ZEN 701 and BELL 115
Special Aluminium BELL 115 in High Street Kensington, London (signpost by others)
Concrete mix to 25 newtons
All Bell Bollards are constructed from cast iron as standard and are 100% recyclable. Standard Bell Bollards are supplied in a primed finish. We recommend that top coats are applied after installation.
General Installation Details The installation instructions left are a guide only. Every care should be taken when preparing the foundations for the Bell Bollard. Diagrams (A) and (B) show a minimum foundation recommendation. In cases of doubt, a professional engineers' advice should be sought. To ensure the Bell Bollard works effectively it should always be set so that the height above ground level remains the same regardless of the type of base. If the Bell Bollard is set on sloping ground; the height above ground level should be determined from its centerline, not edge.
BELL TRAFFIC BOLLARDS
Singapore
800mm
Furnitubes new BELL 138 is a variation of the popular Bell Bollard range. The range is unique to Furnitubes and is well established as effective protection that stops the wheels of vehicles from mounting the kerb, especially on corners. The new BELL 138 variation has a recess designed specifically to house a CIT 538 City Bollard. In addition to providing improved visibility, it also enables the Bell to blend seamlessly within locations where City bollards are used.
BELL 115 Installation Details
“proven to save lives and save money on street maintenance”
Current Installations
If the BELL 115 is being used the installation depth of bollard can be varied to allow compliance with Disability Discrimination guidelines.
- Pedestrian Safety - Width Restriction
BELL 138 housing the CITY Bollard Tyre marks prove that they are used
- Protection of Property
Typical Installations
- Traffic Calming Measures
New York
- Practical and Cost Effective Variable
Below : BELL 100 installed as a width restrictor
London
Above: Typical installation to prevent a vehicle mounting the pavement
All rights reserved. Bell Shaped Traffic Bollards in this or other forms, with or without surface decoration are Copyright Protected (filed in accordance with Universal Copyright Convention in London) & may not be reproduced without the prior permission of Furnitubes International Limited or the original Copyright holder. Registered at Stationers’ Hall, London. No B9/1082/36020
Above: Installation of BELL 115 and Linx 100 railing system established 1946
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Copyright © 1986 Paul M. Harris Innovation and New Product Design.
“Over Sixty Years of Excellence”
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
Macau
Furnitubes International Ltd Meridian House Royal Hill, Greenwich London SE10 8RD tel: +44 (0)20 8378 3200 fax: +44 (0)20 8378 3250 e-mail: sales@furnitubes.com
www.furnitubes.com
Bell Bollard explained
Bell Bollard the solution
Bell Bollard variations
Modern, heavy-duty commercial vehicles can carry large and heavy payloads, often weighing up to 44 tonnes. These huge beasts may be efficient and profitable to their owners, but to pedestrians, roadside structures and street furniture they can present a constant source of damage and danger. Less obvious structures like overhanging or historic buildings are also at risk and in need of protection. Unnecessary damage means costly repairs and does nothing to enhance the appearance of our environment that we are now trying so hard to improve and preserve.
The revolutionary Bell 100 Bollard, manufactured by Furnitubes since 1986, is a simple yet effective solution. Following an extensive study of lorry wheels and undercarriages, a design was created to enable the deflection of a vehicle’s wheels, whilst itself remaining firmly in place and undamaged.
Furnitubes constant development of the Bell Bollard has resulted in the Bell being adapted to meet a range of varying specifications.
TM
TM
TM
For protection to corners of buildings and exposed brickwork, the BELL 340 is an ideal solution. The shape is the same as a standard Bell, but with a segment removed, to allow for easy installation without having to disturb the fabric of the corner.
The bollard's profile is designed to encourage a vehicle's tyres initially to mount its lower curve. By increasing the slope-angle of the bollard above this point, any attempt by the vehicle to rise further is prevented by deflecting the tyre sharply away. The photographs from the video footage (left) shows the bell in action.
Until now, the only answer has been to place conventional bollards close to the areas that need protection. However these are often easily overturned, causing damage to the vehicle involved, pavement, bollard and resulting in an even greater hazard to the pedestrian.
Bell Bollard shown at Hitchin Town Centre. Herts
BELL 340 protecting a building corner
Bumper
For protecting walls or pre-existing structures, the BELL 120 offers the perfect solution. The BELL 120 still has the same deep footings of the BELL 100, but with half the bollard removed to allow it to fit flush to a flat surface.
Air Dam 500
Steering Gear Under Bumper
Bell Bollard will deflect the largest lorries
BELL 120 shown flush against a CITY Bollard
Bell Bollards can provide a stable vehicular barrier, as even high axled lorries would not be able to drive over an obstruction of this height, without causing irreparable damage to its drive train and steering mechanisms. Positioned and aligned at appropriate distances across the road, Bell Bollards can also act as effective width restrictors, preventing oversize vehicles from passing through.
The Bell Bollard is available on CD-ROM. Please contact our sales office for your copy.
Damage to buildings
When used in conjunction with a steel subframe, Furnitubes’ new BELL 500X performs as well as the BELL 100 in situations where underground services make installation difficult, whilst also being easier to transport and handle. It is the same size as the standard bollard, but instead of the deep root, there are four shallow flanges. With proper foundations it is ideal to use on bridges and areas where it is not possible to install the BELL 100. Also, decorative use of the Bell can be made using the BELL 500 version.
Damage to bollards
Bell Bollard used for width restriction & painted for increased visability
BELL 340
BELL 500X
BELL 115
BELL 115 WITH ZENITH
020 8378 3250
© 2008 Copyright Reproduction Prohibited
tel fax
020 8378 3200 020 8378 3250
© 2008 Copyright Reproduction Prohibited
475
475 450
vairable
450
475 475
475 450
450 450
475 450
475 450
www.furnitubes.com
475
475 450
475 450
475 450
475
475
020 8378 3200
1180 1180
Ø 600
1065
tel fax
BELL 115 WITH LINX100100 SYSTEM WITH LINX SYSTEM
600
variable
www.furnitubes.com
450
475 450
475 450
© 2008 Copyright Reproduction Prohibited
BELL 115
BELL 138 WITH ZENITH WITH CITY
300
Ø 600
360
300
360
Ø 600
BELL 500
BELL 500X
600
240 600
BELL 120
BELL 500
Ø 600
BELL 100
360
240
240
BELL 120
Ø 600
BELL 340
Ø 600
BELL 100
BELL 500X prior to installation
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Bell Bollard explained
Bell Bollard the solution
Bell Bollard variations
Modern, heavy-duty commercial vehicles can carry large and heavy payloads, often weighing up to 44 tonnes. These huge beasts may be efficient and profitable to their owners, but to pedestrians, roadside structures and street furniture they can present a constant source of damage and danger. Less obvious structures like overhanging or historic buildings are also at risk and in need of protection. Unnecessary damage means costly repairs and does nothing to enhance the appearance of our environment that we are now trying so hard to improve and preserve.
The revolutionary Bell 100 Bollard, manufactured by Furnitubes since 1986, is a simple yet effective solution. Following an extensive study of lorry wheels and undercarriages, a design was created to enable the deflection of a vehicle’s wheels, whilst itself remaining firmly in place and undamaged.
Furnitubes constant development of the Bell Bollard has resulted in the Bell being adapted to meet a range of varying specifications.
TM
TM
TM
For protection to corners of buildings and exposed brickwork, the BELL 340 is an ideal solution. The shape is the same as a standard Bell, but with a segment removed, to allow for easy installation without having to disturb the fabric of the corner.
The bollard's profile is designed to encourage a vehicle's tyres initially to mount its lower curve. By increasing the slope-angle of the bollard above this point, any attempt by the vehicle to rise further is prevented by deflecting the tyre sharply away. The photographs from the video footage (left) shows the bell in action.
Until now, the only answer has been to place conventional bollards close to the areas that need protection. However these are often easily overturned, causing damage to the vehicle involved, pavement, bollard and resulting in an even greater hazard to the pedestrian.
Bell Bollard shown at Hitchin Town Centre. Herts
BELL 340 protecting a building corner
Bumper
For protecting walls or pre-existing structures, the BELL 120 offers the perfect solution. The BELL 120 still has the same deep footings of the BELL 100, but with half the bollard removed to allow it to fit flush to a flat surface.
Air Dam 500
Steering Gear Under Bumper
Bell Bollard will deflect the largest lorries
BELL 120 shown flush against a CITY Bollard
Bell Bollards can provide a stable vehicular barrier, as even high axled lorries would not be able to drive over an obstruction of this height, without causing irreparable damage to its drive train and steering mechanisms. Positioned and aligned at appropriate distances across the road, Bell Bollards can also act as effective width restrictors, preventing oversize vehicles from passing through.
The Bell Bollard is available on CD-ROM. Please contact our sales office for your copy.
Damage to buildings
When used in conjunction with a steel subframe, Furnitubes’ new BELL 500X performs as well as the BELL 100 in situations where underground services make installation difficult, whilst also being easier to transport and handle. It is the same size as the standard bollard, but instead of the deep root, there are four shallow flanges. With proper foundations it is ideal to use on bridges and areas where it is not possible to install the BELL 100. Also, decorative use of the Bell can be made using the BELL 500 version.
Damage to bollards
Bell Bollard used for width restriction & painted for increased visability
BELL 340
BELL 500X
BELL 115
BELL 115 WITH ZENITH
020 8378 3250
© 2008 Copyright Reproduction Prohibited
tel fax
020 8378 3200 020 8378 3250
© 2008 Copyright Reproduction Prohibited
475
475 450
vairable
450
475 475
475 450
450 450
475 450
475 450
www.furnitubes.com
475
475 450
475 450
475 450
475
475
020 8378 3200
1180 1180
Ø 600
1065
tel fax
BELL 115 WITH LINX100100 SYSTEM WITH LINX SYSTEM
600
variable
www.furnitubes.com
450
475 450
475 450
© 2008 Copyright Reproduction Prohibited
BELL 115
BELL 138 WITH ZENITH WITH CITY
300
Ø 600
360
300
360
Ø 600
BELL 500
BELL 500X
600
240 600
BELL 120
BELL 500
Ø 600
BELL 100
360
240
240
BELL 120
Ø 600
BELL 340
Ø 600
BELL 100
BELL 500X prior to installation
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Bell Bollard explained
Bell Bollard the solution
Bell Bollard variations
Modern, heavy-duty commercial vehicles can carry large and heavy payloads, often weighing up to 44 tonnes. These huge beasts may be efficient and profitable to their owners, but to pedestrians, roadside structures and street furniture they can present a constant source of damage and danger. Less obvious structures like overhanging or historic buildings are also at risk and in need of protection. Unnecessary damage means costly repairs and does nothing to enhance the appearance of our environment that we are now trying so hard to improve and preserve.
The revolutionary Bell 100 Bollard, manufactured by Furnitubes since 1986, is a simple yet effective solution. Following an extensive study of lorry wheels and undercarriages, a design was created to enable the deflection of a vehicle’s wheels, whilst itself remaining firmly in place and undamaged.
Furnitubes constant development of the Bell Bollard has resulted in the Bell being adapted to meet a range of varying specifications.
TM
TM
TM
For protection to corners of buildings and exposed brickwork, the BELL 340 is an ideal solution. The shape is the same as a standard Bell, but with a segment removed, to allow for easy installation without having to disturb the fabric of the corner.
The bollard's profile is designed to encourage a vehicle's tyres initially to mount its lower curve. By increasing the slope-angle of the bollard above this point, any attempt by the vehicle to rise further is prevented by deflecting the tyre sharply away. The photographs from the video footage (left) shows the bell in action.
Until now, the only answer has been to place conventional bollards close to the areas that need protection. However these are often easily overturned, causing damage to the vehicle involved, pavement, bollard and resulting in an even greater hazard to the pedestrian.
Bell Bollard shown at Hitchin Town Centre. Herts
BELL 340 protecting a building corner
Bumper
For protecting walls or pre-existing structures, the BELL 120 offers the perfect solution. The BELL 120 still has the same deep footings of the BELL 100, but with half the bollard removed to allow it to fit flush to a flat surface.
Air Dam 500
Steering Gear Under Bumper
Bell Bollard will deflect the largest lorries
BELL 120 shown flush against a CITY Bollard
Bell Bollards can provide a stable vehicular barrier, as even high axled lorries would not be able to drive over an obstruction of this height, without causing irreparable damage to its drive train and steering mechanisms. Positioned and aligned at appropriate distances across the road, Bell Bollards can also act as effective width restrictors, preventing oversize vehicles from passing through.
The Bell Bollard is available on CD-ROM. Please contact our sales office for your copy.
Damage to buildings
When used in conjunction with a steel subframe, Furnitubes’ new BELL 500X performs as well as the BELL 100 in situations where underground services make installation difficult, whilst also being easier to transport and handle. It is the same size as the standard bollard, but instead of the deep root, there are four shallow flanges. With proper foundations it is ideal to use on bridges and areas where it is not possible to install the BELL 100. Also, decorative use of the Bell can be made using the BELL 500 version.
Damage to bollards
Bell Bollard used for width restriction & painted for increased visability
BELL 340
BELL 500X
BELL 115
BELL 115 WITH ZENITH
020 8378 3250
© 2008 Copyright Reproduction Prohibited
tel fax
020 8378 3200 020 8378 3250
© 2008 Copyright Reproduction Prohibited
475
475 450
vairable
450
475 475
475 450
450 450
475 450
475 450
www.furnitubes.com
475
475 450
475 450
475 450
475
475
020 8378 3200
1180 1180
Ø 600
1065
tel fax
BELL 115 WITH LINX100100 SYSTEM WITH LINX SYSTEM
600
variable
www.furnitubes.com
450
475 450
475 450
© 2008 Copyright Reproduction Prohibited
BELL 115
BELL 138 WITH ZENITH WITH CITY
300
Ø 600
360
300
360
Ø 600
BELL 500
BELL 500X
600
240 600
BELL 120
BELL 500
Ø 600
BELL 100
360
240
240
BELL 120
Ø 600
BELL 340
Ø 600
BELL 100
BELL 500X prior to installation
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Bell Bollard new additions
Bell Bollard installation
TM
TM
The BELL 115 has been designed to allow the installation of a Bell Bollard and a 115mm diameter post or bollard within the same footings. This combination enables the Bell Bollard to still deflect vehicles and protect structures from damage, but where necessary can now act as a high visibility post.
When the BELL 115 is installed with a bollard or post of 1000mm height or greater, the Bell Bollard will conform to disability discrimination guidelines for partially sighted pedestrians.
450mm
G.L.
600mm
The ability of the BELL 115 to act as a pedestrian barrier is further enhanced by incorporating the Bell Bollard into the LINX 100 Railing System. By combining the two products it is possible to design an integrated, cost effective vehicular and pedestrian barrier, with the Bell Bollard protecting any corner post from damage by passing vehicles.
475mm
50mm max protrusion above G.L.
Bell Loop
Diagram B
Kerb Line
800mm
BELL 115 and Linx railing
Diagram A
Parallel to kerb High Visability ZEN 701 and BELL 115
Special Aluminium BELL 115 in High Street Kensington, London (signpost by others)
Concrete mix to 25 newtons
All Bell Bollards are constructed from cast iron as standard and are 100% recyclable. Standard Bell Bollards are supplied in a primed finish. We recommend that top coats are applied after installation.
General Installation Details The installation instructions left are a guide only. Every care should be taken when preparing the foundations for the Bell Bollard. Diagrams (A) and (B) show a minimum foundation recommendation. In cases of doubt, a professional engineers' advice should be sought. To ensure the Bell Bollard works effectively it should always be set so that the height above ground level remains the same regardless of the type of base. If the Bell Bollard is set on sloping ground; the height above ground level should be determined from its centerline, not edge.
BELL TRAFFIC BOLLARDS
Singapore
800mm
Furnitubes new BELL 138 is a variation of the popular Bell Bollard range. The range is unique to Furnitubes and is well established as effective protection that stops the wheels of vehicles from mounting the kerb, especially on corners. The new BELL 138 variation has a recess designed specifically to house a CIT 538 City Bollard. In addition to providing improved visibility, it also enables the Bell to blend seamlessly within locations where City bollards are used.
BELL 115 Installation Details
“proven to save lives and save money on street maintenance”
Current Installations
If the BELL 115 is being used the installation depth of bollard can be varied to allow compliance with Disability Discrimination guidelines.
- Pedestrian Safety - Width Restriction
BELL 138 housing the CITY Bollard Tyre marks prove that they are used
- Protection of Property
Typical Installations
- Traffic Calming Measures
New York
- Practical and Cost Effective Variable
Below : BELL 100 installed as a width restrictor
London
Above: Typical installation to prevent a vehicle mounting the pavement
All rights reserved. Bell Shaped Traffic Bollards in this or other forms, with or without surface decoration are Copyright Protected (filed in accordance with Universal Copyright Convention in London) & may not be reproduced without the prior permission of Furnitubes International Limited or the original Copyright holder. Registered at Stationers’ Hall, London. No B9/1082/36020
Above: Installation of BELL 115 and Linx 100 railing system established 1946
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Copyright © 1986 Paul M. Harris Innovation and New Product Design.
“Over Sixty Years of Excellence”
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
Macau
Furnitubes International Ltd Meridian House Royal Hill, Greenwich London SE10 8RD tel: +44 (0)20 8378 3200 fax: +44 (0)20 8378 3250 e-mail: sales@furnitubes.com
www.furnitubes.com
Bell Bollard new additions
Bell Bollard installation
TM
TM
The BELL 115 has been designed to allow the installation of a Bell Bollard and a 115mm diameter post or bollard within the same footings. This combination enables the Bell Bollard to still deflect vehicles and protect structures from damage, but where necessary can now act as a high visibility post.
When the BELL 115 is installed with a bollard or post of 1000mm height or greater, the Bell Bollard will conform to disability discrimination guidelines for partially sighted pedestrians.
450mm
G.L.
600mm
The ability of the BELL 115 to act as a pedestrian barrier is further enhanced by incorporating the Bell Bollard into the LINX 100 Railing System. By combining the two products it is possible to design an integrated, cost effective vehicular and pedestrian barrier, with the Bell Bollard protecting any corner post from damage by passing vehicles.
475mm
50mm max protrusion above G.L.
Bell Loop
Diagram B
Kerb Line
800mm
BELL 115 and Linx railing
Diagram A
Parallel to kerb High Visability ZEN 701 and BELL 115
Special Aluminium BELL 115 in High Street Kensington, London (signpost by others)
Concrete mix to 25 newtons
All Bell Bollards are constructed from cast iron as standard and are 100% recyclable. Standard Bell Bollards are supplied in a primed finish. We recommend that top coats are applied after installation.
General Installation Details The installation instructions left are a guide only. Every care should be taken when preparing the foundations for the Bell Bollard. Diagrams (A) and (B) show a minimum foundation recommendation. In cases of doubt, a professional engineers' advice should be sought. To ensure the Bell Bollard works effectively it should always be set so that the height above ground level remains the same regardless of the type of base. If the Bell Bollard is set on sloping ground; the height above ground level should be determined from its centerline, not edge.
BELL TRAFFIC BOLLARDS
Singapore
800mm
Furnitubes new BELL 138 is a variation of the popular Bell Bollard range. The range is unique to Furnitubes and is well established as effective protection that stops the wheels of vehicles from mounting the kerb, especially on corners. The new BELL 138 variation has a recess designed specifically to house a CIT 538 City Bollard. In addition to providing improved visibility, it also enables the Bell to blend seamlessly within locations where City bollards are used.
BELL 115 Installation Details
“proven to save lives and save money on street maintenance”
Current Installations
If the BELL 115 is being used the installation depth of bollard can be varied to allow compliance with Disability Discrimination guidelines.
- Pedestrian Safety - Width Restriction
BELL 138 housing the CITY Bollard Tyre marks prove that they are used
- Protection of Property
Typical Installations
- Traffic Calming Measures
New York
- Practical and Cost Effective Variable
Below : BELL 100 installed as a width restrictor
London
Above: Typical installation to prevent a vehicle mounting the pavement
All rights reserved. Bell Shaped Traffic Bollards in this or other forms, with or without surface decoration are Copyright Protected (filed in accordance with Universal Copyright Convention in London) & may not be reproduced without the prior permission of Furnitubes International Limited or the original Copyright holder. Registered at Stationers’ Hall, London. No B9/1082/36020
Above: Installation of BELL 115 and Linx 100 railing system established 1946
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
tel fax
020 8378 3200 020 8378 3250
Copyright © 1986 Paul M. Harris Innovation and New Product Design.
“Over Sixty Years of Excellence”
© 2008 Copyright Reproduction Prohibited
www.furnitubes.com
Macau
Furnitubes International Ltd Meridian House Royal Hill, Greenwich London SE10 8RD tel: +44 (0)20 8378 3200 fax: +44 (0)20 8378 3250 e-mail: sales@furnitubes.com
www.furnitubes.com