Greensmaster_Greens_Mowers by negimachi negimachi

Greensmaster Flex 1800 & 2100 ®

The new Greensmaster Flex™, available in both 18 and 21 inch cutting widths, takes Toro’s industry leading cutting performance to a whole new level. Additional innovations in the areas of productivity, operational versatility and serviceability combine to make this mower an outstanding value. ®

Greensmaster Flex 1800 & 2100 Specifications* ®

GREENSMASTER FLEX 1800, MODEL 04041 ENGINE

GREENSMASTER FLEX 2100, MODEL 04040

Subaru Heavy-Duty Industrial, 4.5 HP, OHC, 4-cycle, CARB, EPA, EU certified gasoline engine with integral lighting coil. Displacement: 7.7 cu in. (126 cc). Cast iron cylinder sleeve. Electronic ignition. Maximum noise suppression muffler. ®

FUEL CAPACITY

2.85 quarts (2.7 liters) regular grade unleaded gasoline.

TRANSMISSION

Engine powered ramp-engagement style friction clutch to the first stage of a multi-ribbed poly-V belt drive. The traction drums are belt driven through a spur gear planetary differential with integral band style service/parking brake.

Maintenance GROUND SPEED traction drum CONTROLS handle transport tires/ kickstand reel construction

No grease zerks, sealed bearing design reduces daily maintenance. Mowing speed: 1.6-3.7 mph (2.5-5.9 km/h). Transport speed (maximum): 5.7 mph (9.2 km/h). Dual cast aluminum 7.5” (19 cm) diameter with taper on outer 2” (5 cm). Engine Controls: Recoil starter, choke, fuel shut-off. Handle Controls: on/off (‘ignition’) switch, hour meter, throttle, dual function traction/ reel control lever, operator presence control, service/park brake lever, on/off light switch (optional blank slot in console). Loop style, molded contour upper, 1” (2.5 cm) diameter lower tube. Two angular adjustments and lift assist kickstand with 2.0 inches of telescoping adjustment. Quick detachable 3.00/3.25 x 6 pneumatic. Kickstand standard equipment. Loop style with service position lock, 1” (2.5 cm) diameter tube. 8-Blade Reel: 5” (12.7 cm) diameter, 8 high carbon steel blades welded to 5 steel spiders (no 8-blade, 18” available). 11-Blade Reel: 5” (12.7 cm) diameter, 11 high carbon steel blades welded to 5 steel spiders. 14-Blade Reel: 5” (12.7 cm) diameter, 14 high carbon steel blades welded to 5 steel spiders.

suspension width of cut

Semi-floating cutting unit separable from drive unit, pivoting around reel centerline (pitch axis) and pivoting around bedknife centerline side to side (roll axis).

height of cut

Front roller adjustable with 2 position rear roller: 1st position (spacer on top) 1/16” - 5/32” (1.59 – 3.97 mm). 2nd position (spacer below) 1/8” - 19/64” (3.17 – 7.54 mm).

clip frequencIES REEL Drive Cutting unit Const. Cutting unit adjust./ service bedknife grass basket rollers Working weight CERTIFICATION WARRANTy

18" (45.7 cm)

21" (53.3 cm)

Reel drive consists of three pulleys of different diameter. 6-clip adjustments per reel, based on pulley configuration. Transmission reel clutch shaft to a telescoping drive shaft with a pair of beam style couplers. Telescoping sleeve is retractable for ease of cutting unit removal. Cast aluminum and machined tubular steel frame. Cutting unit detachable from traction unit. Dual screw “click” adjustments to reel. Front roller height of cut adjustment. Sealed stainless steel reel bearings. Bedknife is high carbon through-hardened steel. EdgeMax Microcut Bedknife is standard on 11 & 14-blade cutting unit. EdgeMax bedknife is solid tool steel. TM

Molded polyethylene with integrated graphics highlighting overlap guidelines, vented for high-efficiency collection. Front Roller: Optional – must be ordered. Rear Roller: Aluminum full roller 2” (5.1 cm) diameter with sealed bearings. TBD

260 lbs. (118 kg) w/basket, w/o transport tires and groomer.

ANSI & CE Two-year limited warranty. Refer to the Operator’s Manual for further details.

GREENSMASTER FLEX 1800 ACCESSORIES CUTTING UNITS & REEL OPTIONS 04254 04253 119-4102 119-4101

14-Blade DPA Cutting Unit 11-Blade DPA Cutting Unit 14-Blade Reel 11-Blade Reel

GROOMER OPTIONS 04259 04263 04264 120-9661

STANDARD CUTTING UNIT EQUIPMENT 117-1530

EdgeMax Microcut Bedknife TM

BEDKNIFE & BEDBAR OPTIONS 98-7260 110-2301 110-2300 98-7261 117-1532 117-1530 120-9600 110-2282-01 94-9010

Tournament Bedknife Low Cut Bedknife Extended Microcut Bedknife Microcut Bedknife EdgeMax Tournament Bedknife EdgeMax Microcut Bedknife High Height of Cut Kit Less Aggressive Bedbar Height of Cut Adjustment Bar TM

ROLLER OPTIONS 120-9607 120-9609 120-9611 115-7361 114-4630

Front Narrow Wiehle Roller Front Wide Wiehle Roller Front Full Steel Roller (2.5” dia.) Front Roller Extension Kit Rear Roller Adjustment Kit

GREENSMASTER FLEX 2100 ACCESSORIES CUTTING UNITS & REEL OPTIONS

Flex Groomer Drive, Fwd Rotating Groomer Reel, Carbide (18") Grooming Brush (18”) Groomer Quick Up Kit

04251 04252 119-4105 119-4104 119-4103

SCRAPER OPTIONS 120-9615 120-9616 120-9617 120-9621 120-9622 120-9623 120-9624 120-9625 120-9626 120-9627

STANDARD CUTTING UNIT EQUIPMENT

Narrow Wiehle Roller Scraper Wide Wiehle Roller Scraper Full Roller Scraper Narrow Wiehle Roller Scraper Brush Wide Wiehle Roller Scraper Brush Full Roller Scraper Brush Narrow Wiehle Roller Scraper Comb Wide Wiehle Roller Scraper Comb Full Roller Scraper Comb Scraper Kit with Rear Roller

115-1880 99-3794-03

EdgeMax Microcut Bedknife Aggressive Bed Bar TM

BEDKNIFE & BEDBAR OPTIONS 93-4263 93-4264 108-4303 93-4262 108-4302 115-1881 120-9600 106-2648-01 94-9010

TRACTION UNIT ACCESSORIES 04265 04266 04123 04399

11-Blade DPA Cutting Unit 14-Blade DPA Cutting Unit 14-Blade Reel 11-Blade Reel 8-Blade Reel

LED Light Kit Push Broom Brush Wheel Kit Turf Evaluator

Tournament Bedknife Low Cut Bedknife Extended Microcut Bedknife Microcut Bedknife Extended Tournament Bedknife EdgeMax Tournament Bedknife High Height of Cut Kit Less Aggressive Bedbar Height of Cut Adjustment Bar TM

TRACTION UNIT ACCESSORIES 04265 04266 04123 04399

LED Light Kit Push Broom Brush Wheel Kit Turf Evaluator

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor. The Greensmaster Flex 1800 & 2100 are manufactured in Tomah, WI ISO 9002 Certified Plant.

ROLLER OPTIONS 04255 04256 04257 04258 115-7356 120-9595 115-7361 114-4630

Front Narrow Wiehle Roller Front Wide Wiehle Roller Front Full Roller Long Front Narrow Wiehle Roller Rear Full Roller – Aluminum Rear Full Roller – Steel Front Roller Extension Kit Rear Roller Adjustment Kit

GROOMER OPTIONS 04259 04260 04711 04712 04713 120-9661

Flex Groomer Drive, Fwd Rotating Flex Groomer Drive, Counter Rotating Groomer Reel, Carbide (RH) Groomer Reel, Spring Steel (RH) Grooming Brush Groomer Quick Up Kit

SCRAPER OPTIONS 115-7374 115-7375 115-7376 115-7377 115-7378 115-7379 115-7380 115-7381 115-7382 115-7383

Greensmaster eFlex 1800 & 2100 ®

The new Greensmaster eFlex™, available in both 18 and 21 inch cutting widths, takes Toro’s industry leading cutting performance to a whole new level. Game-changing Lithium Ion battery technology combined with Toro innovations for improved cutting performance, allow you to quietly mow up to 9 average greens (45,000 sq. feet) on a single charge! Additional innovations in the areas of productivity, operational versatility and serviceability combine to provide a more environmentally friendly “EnergySmart™” solution and ROI. ®

Greensmaster eFlex 1800 & 2100 Specifications* TM

GREENSMASTER eFLEX 1800, MODEL 04043 POWER ELECTRIC MOTOR Battery charger TRANSMISSION Maintenance GROUND SPEED traction drum

GREENSMASTER eFLEX 2100, MODEL 04042

Lithium-Ion battery pack – nominal 53-Volt 35 A-Hr (42 – 64 volt, 1.68 kW-hr) with integrated battery management system utilizing CAN communication with the machine controller and charger. Single battery affixed to unit and charged onboard. Brushless permanent magnet DC motor – nominal 1.2 kW (~20A continuous, 30A peak) with integral motor controller and helical gear reduction. Voltage and current controlled with CAN communication to manage storage wake-up and maintenance features. Complies to max voltage and current limits directed by the battery management system. Permanent Magnet DC motor directly coupled to the first stage of a multi-ribbed poly-V belt drive. The traction drums are belt driven through a spur gear planetary differential with integral band style service/parking brake. No grease zerks, sealed bearing design reduces daily maintenance. Mowing speed: 0.9-3.7 mph (1.4-5.9 km/h). Transport speed (maximum): 5.7 mph (9.2 km/h). Dual cast aluminum 7.5” (19 cm) diameter with taper on outer 2” (5 cm).

CONTROLS

Start/On/Off (‘ignition’) switch, LCD Information Center (reports multiple parameters including hours, battery life, faults, etc.) throttle, dual function traction/reel control lever, operator presence control, on/off ‘EZ-Turn’ switch, service/park brake lever, on/off light switch (optional blank slot in console).

handle transport tires/ kickstand

Loop style, molded contour upper, 1” (2.5 cm) diameter lower tube. Two angular adjustments and lift assist on kickstand with 2.0 inches of telescoping adjustment.

reel construction

8-Blade Reel: 5” (12.7 cm) diameter, 8 high carbon steel blades welded to 5 steel spiders (no 8-blade, 18” available). 11-Blade Reel: 5” (12.7 cm) diameter, 11 high carbon steel blades welded to 5 steel spiders. 14-Blade Reel: 5” (12.7 cm) diameter, 14 high carbon steel blades welded to 5 steel spiders.

suspension width of cut height of cut clip frequencIES REEL Drive Cutting unit Const. Cutting unit adjust./ service bedknife grass basket rollers Working weight CERTIFICATION WARRANTy

Quick detachable 3.00/3.25 x 6 pneumatic. Kickstand standard equipment. Loop style with service position lock, 1” (2.5 cm) diameter tube.

Semi-floating cutting unit separable from drive unit, pivoting around reel centerline (pitch axis) and pivoting around bedknife centerline side to side (roll axis). 18" (45.7 cm)

21" (53.3 cm)

Front roller adjustable with 2 position rear roller: 1st position (spacer on top) 1/16” - 5/32” (1.59 – 3.97 mm). 2nd position (spacer below) 1/8” - 19/64” (3.17 – 7.54 mm) Reel drive consists of three pulleys of different diameter. 6-clip adjustments per reel, based on pulley configuration. Transmission reel clutch shaft to a telescoping drive shaft with a pair of beam style couplers. Telescoping sleeve is retractable for ease of cutting unit removal. Cast aluminum and machined tubular steel frame. Cutting unit detachable from traction unit. Dual screw “click” adjustments to reel. Front roller height of cut adjustment. Sealed stainless steel reel bearings. Bedknife is high carbon through-hardened steel. EdgeMax Microcut Bedknife is standard on 11 & 14-blade cutting unit. EdgeMax bedknife is solid tool steel. TM

293 lbs. (133 kg) w/basket, w/o transport tires and groomer.

ANSI/CE/WEEE/ROHS Two-year limited warranty. Years 3-5 prorated warranty on Lithium-Ion Battery. Refer to the Operator’s Manual for further details.

GREENSMASTER eFLEX 1800 ACCESSORIES CUTTING UNITS & REEL OPTIONS 04254 04253 119-4102 119-4101

14-Blade DPA Cutting Unit 11-Blade DPA Cutting Unit 14-Blade Reel 11-Blade Reel

GROOMER OPTIONS 04259 04263 04264 120-9661

STANDARD CUTTING UNIT EQUIPMENT 117-1530

EdgeMax Microcut Bedknife TM

BEDKNIFE & BEDBAR OPTIONS 98-7260 110-2301 110-2300 98-7261 117-1532 117-1530 120-9600 110-2282-01 94-9010

ROLLER OPTIONS 120-9607 120-9609 120-9611 115-7361 114-4630

Front Narrow Wiehle Roller Front Wide Wiehle Roller Front Full Steel Roller (2.5” dia.) Front Roller Extension Kit Rear Roller Adjustment Kit

GREENSMASTER eFLEX 2100 ACCESSORIES CUTTING UNITS & REEL OPTIONS

Flex Groomer Drive, Fwd Rotating Groomer Reel, Carbide (18") Grooming Brush (18”) Groomer Quick Up Kit

04251 04252 119-4105 119-4104 119-4103

SCRAPER OPTIONS 120-9615 120-9616 120-9617 120-9621 120-9622 120-9623 120-9624 120-9625 120-9626 120-9627

STANDARD CUTTING UNIT EQUIPMENT

115-1880 99-3794-03

EdgeMax Microcut Bedknife Aggressive Bed Bar TM

BEDKNIFE & BEDBAR OPTIONS 93-4263 93-4264 108-4303 93-4262 108-4302 115-1881 120-9600 106-2648-01 94-9010

TRACTION UNIT ACCESSORIES 04265 04266 04123 04399

11-Blade DPA Cutting Unit 14-Blade DPA Cutting Unit 14-Blade Reel 11-Blade Reel 8-Blade Reel

LED Light Kit Push Broom Brush Wheel Kit Turf Evaluator

TRACTION UNIT ACCESSORIES 04265 04266 04123 04399

LED Light Kit Push Broom Brush Wheel Kit Turf Evaluator

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor. The Greensmaster eFlex 1800 & 2100 are manufactured in Tomah, WI ISO 9002 Certified Plant.

ROLLER OPTIONS 04255 04256 04257 04258 115-7356 120-9595 115-7361 114-4630

GROOMER OPTIONS 04259 04260 04711 04712 04713 120-9661

Flex Groomer Drive, Fwd Rotating Flex Groomer Drive, Counter Rotating Groomer Reel, Carbide (RH) Groomer Reel, Spring Steel (RH) Grooming Brush Groomer Quick Up Kit

SCRAPER OPTIONS 115-7374 115-7375 115-7376 115-7377 115-7378 115-7379 115-7380 115-7381 115-7382 115-7383

Greensmaster 800 ÂŽ

Uniquely weighted, front to rear, the Greensmaster 800 deeply penetrates the turfâ&#x20AC;&#x2122;s surface for a lower, more consistent height of cut, and straight tracking.

Greensmaster 800 Series Specifications* ®

GREENSMASTER 800, MODEL 04054 Subaru Heavy-Duty Industrial, 4.5 HP, OHC, 4-cycle, CARB, EPA, EU certified gasoline engine with integral lighting coil. Displacement: 7.7 cu in. (126 cc). Cast iron cylinder sleeve. Electronic ignition. Maximum noise suppression muffler. ®

ENGINE FUEL CAPACITY

2.85 quarts (2.7 liters) regular grade unleaded gasoline.

TRACTION AND IMPLEMENT DRIVE

Engine to countershaft drive: two “A” section V-belts. Timing belts from countershaft to differential, drive drum and reel.

GROUND SPEED

Mowing speed: 1.5 mph (2.4 km/h) to 3.3 mph (5.3 km/h). Transport speed (maximum): 5.0 mph (8.0 km/h).

DIFFERENTIAL

Peerless Series 100.

CLUTCHES

Traction: inside belt idler. Reel: jaw type.

BRAKE

Service/parking-band type.

TRACTION DRUM

Dual cast aluminum, 7.5" (19 cm) diameter. Engine mounted; recoil starter, choke. Handle mounted: hour meter, on/off switch, throttle lever, traction engage lever, service/park brake lever. Frame mounted: reel drive engage lever. Safety devices: neutral interlock system, servicing/park brake, enclosed drive system. Optional: Operator Presence Control.

CONTROLS HANDLE

Loop style; 1" (2.5 cm) diameter with easy pull pin height adjustment, operator selected.

TRANSPORT TIRES/ KICKSTAND

Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bars) tire pressure. Kickstand is standard.

REEL CONSTRUCTION

5" (12.7 cm) diameter, 14 carbon steel blades welded to 5 stamped steel spiders. Optional 8-blade & 11-blade reel.

WIDTH OF CUT

18" (45.7 cm)

HEIGHT OF CUT

5/64" to 1" (2.0-25.4 mm) Standard14-Blade: .13" (3.3 mm) Optional 8-Blade: .23" (5.8 mm) Optional 11-Blade: .16" (4.1 mm)

CLIP BEDKNIFE/BEDBAR

w/Clip Kit .194" (4.9 mm) .34" (8.6 mm) .25" (6.4 mm)

Dual screw “click” adjustment to reel. EdgeMax Microcut Bedknife standard TM

GRASS BASKET

Patented design: molded polyethylene, baffled and vented for high efficiency collection.

FRONT ROLLER

Aluminum Wiehle roller standard; 2" (5.1 cm) diameter, .200 spacing.

WEIGHT

210 lbs. (95.3 kg) with aluminum Wiehle roller, kickstand and grass basket, without transport tires and groomer.

CERTIFICATION

Certified to meet ANSI specifications B71.4-2004 and European Community (CE) specifications with required kits installed.

WARRANTY

Two-year limited warranty. Refer to the Operator’s Manual for further details.

GREENSMASTER 800 ACCESSORIES REEL OPTIONS 98-5919

11-Blade Reel

BEDKNIFE & BEDBAR OPTIONS 98-7260

Tournament Bedknife

93-4262

Microcut Bedknife

110-2301

ROLLER & ROLLER SCRAPER OPTIONS

GROOMING OPTIONS

99-6240

Narrow Wiehle Roller (Standard)

04133

Groomer

98-7264

Wide Wiehle Roller

04109

Thatching Kit (dynaBLADE)

104-2640

Full Roller

98-7257

Full Roller Scraper

TRACTION UNIT ACCESSORIES 112-9282

Operator Presence Bail Kit

Low Cut Bedknife

04266

Push Broom Brush

117-1530

Extended Microcut Bedknife

04123

Wheel Kit

115-1880

EdgeMax

115-1886

Traction Slow Down Kit

117-1532

EdgeMax Tournament Bedknife

65-9000

Clip Kit

94-9010

Height of Cut Adjustment Bar

04399

Turf Evaluator

120-2731-03

Bedbar – Aggressive

115-4754

Wireless Hour Meter Wire Harness (For Wireless Hour Meter)

65-8560

Roller Extension

Microcut Bedknife

120-9690

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster 800 is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster 1000 ÂŽ

Uniquely weighted, front to rear, the Greensmaster 1000 deeply penetrates the turfâ&#x20AC;&#x2122;s surface for a lower, more consistent height of cut, and straight tracking.

Greensmaster 1000 Series Specifications* ®

GREENSMASTER 1000, MODEL 04055 Subaru Heavy-Duty Industrial, 4.5 HP, OHC, 4-cycle, CARB, EPA, EU certified gasoline engine with integral lighting coil. Displacement: 7.7 cu in. (126 cc). Cast iron cylinder sleeve. Electronic ignition. Maximum noise suppression muffler. ®

ENGINE FUEL CAPACITY

2.85 quarts (2.7 liters) regular grade unleaded gasoline.

TRACTION AND IMPLEMENT DRIVE

Engine to countershaft drive: two “A” section V-belts. Timing belts from countershaft to differential, drive drum and reel.

GROUND SPEED

Mowing speed: 1.5 mph (2.4 km/h) to 3.3 mph (5.3 km/h). Transport speed (maximum): 5.0 mph (8.0 km/h).

DIFFERENTIAL

Peerless Series 100.

CLUTCHES

Traction: inside belt idler. Reel: jaw type.

BRAKE

Service/parking-band type.

TRACTION DRUM

CONTROLS HANDLE

Loop style; 1" (2.5 cm) diameter with easy pull pin height adjustment, operator selected.

TRANSPORT TIRES/ KICKSTAND

Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bars) tire pressure. Kickstand is standard.

REEL CONSTRUCTION

5" (12.7 cm) diameter, 11 carbon steel blades welded to 5 stamped steel spiders. Optional 8-blade & 14-blade reel.

WIDTH OF CUT

21" (53.3 cm)

HEIGHT OF CUT

5/64" to 1" (2.0-25.4 mm) Standard 11-Blade: .16" (4.1 mm) Optional 8-Blade: .23" (5.8 mm) Optional 14-Blade: .13" (3.3 mm)

CLIP BEDKNIFE/BEDBAR

w/Clip Kit .25" (6.4 mm) .34" (8.6 mm) .194" (4.9 mm)

Dual screw “click” adjustment to reel. EdgeMax Microcut Bedknife standard TM

GRASS BASKET

Patented design: molded polyethylene, baffled and vented for high efficiency collection.

FRONT ROLLER

Aluminum Wiehle roller standard; 2" (5.1 cm) diameter, .200 spacing.

WEIGHT

295 lbs. (133.8 kg) with aluminum Wiehle roller, kickstand and grass basket, without transport tires and groomer.

CERTIFICATION

Certified to meet ANSI specifications B71.4-2004 and European Community (CE) specifications with required kits installed.

WARRANTY

Two-year limited warranty. Refer to the Operator’s Manual for further details.

GREENSMASTER 1000 ACCESSORIES STANDARD EQUIPMENT

ROLLER OPTIONS

GROOMING OPTIONS

99-6241

Narrow Wiehle Roller

88-6790

Wide Wiehle Roller

04131

Groomer

115-1880

EdgeMax Microcut Bedknife

52-3590

Swaged Roller

105-9640

Groomer Brush Assembly

93-9045

Long Front Wiehle Roller

04109

Thatching Kit (dynaBLADE)

71-1550

Cast Iron Wiehle Roller

04111

Thatching Kit

104-2642

Full Roller

65-8560

Front Roller Extension Kit

107-1588

Rebuild Kit

REEL OPTIONS 93-6087

8-Blade Reel

117-1449

14-Blade Reel

BEDKNIFE & BEDBAR OPTIONS 93-4262

Microcut Bedknife

108-4303

Extended Microcut Bedknife

93-4264

Low Cut Bedknife

115-1881

EdgeMax Tournament Bedknife

93-4263

Tournament Bedknife

94-9010

Height of Cut Adjustment Bar

112-9279-03

Bedbar – Aggressive

TRACTION UNIT ACCESSORIES 04062

LED Light Kit

112-9282

Operator Presence Bail Kit

SCRAPER OPTIONS

04266

Push Broom Brush

112-9285

Smooth Scraper

04123

Wheel Kit

112-9288

Wide Wiehle Roller Scraper

115-1886

Traction Slow Down Kit

112-9286

Scraper Brush

65-9000

Clip Kit

112-9289

Narrow Wiehle Roller Scraper

115-1880

18-Tooth Pulley

112-9287

Scraper Comb

04399

Turf Evaluator

115-4754

Wireless Hour Meter Wire Harness (For Wireless Hour Meter)

120-9690

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster 1000 is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster 1600 速

Its wider 26" cut and extended height of cut range offers greater productivity. Ideal for tees, aprons, even large greens.

Greensmaster 1600 Specifications* ®

GREENSMASTER 1600**, MODEL 04056 ENGINE FUEL CAPACITY TRACTION DRIVE REEL DRIVE GROUND SPEED DIFFERENTIAL CLUTCHES BRAKE TRACTION DRUM CONTROLS TRANSPORT/TIRES/ KICKSTAND REEL CONSTRUCTION WIDTH OF CUT HEIGHT OF CUT CLIP BEDKNIFE/BEDBAR

2.85 quarts (2.7 liters) regular grade unleaded gasoline. Belt powered, split drum with differential. Two “A” section V-belts with manually activated idler pulley provide drive engagement/disengagement. Positive drive belt powered reel. Manually activated jaw-type clutch provides drive engagement/disengagement. Mowing speed: 1.5 mph (2.4 km/h) to 3.3 mph (5.3 km/h). Transport speed (maximum): 5.0 mph (8.0 km/h). Peerless Series 100. Traction: inside belt idler. Reel: jaw type. Servicing brake; band type. Dual cast aluminum. 7.5" (19 cm) diameter. Engine mounted: recoil starter, choke. Handle mounted: Hour meter, on/off switch, throttle lever, traction engage lever, service/part brake lever. Frame mounted: reel drive engage lever. Safety devices: neutral interlock system, servicing/park brake, enclosed drive system. Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bar) tire pressure. Kickstand: loop style, 1" (2.5 cm) diameter tube. Kickstand standard. 5" (12.7 cm) diameter, 8 high carbon steel blades welded to 6 stamped steel spiders. 26" (66 cm) .125"-1.25" (3.2 -31.8 mm) .23" (5.8 mm) - 8-blade reel; .34" (8.6 mm) with Clip Kit, P/N 65-9000. .16" (4.1 mm) - 11-blade reel; .25" (6.4 mm) with Clip Kit. Dual screw “click” adjustment to reel; bedknife is high carbon through-hardened steel, cutting edge hardness of 48-54 Rc. Low-cut bedknife standard.

GRASS BASKET

Molded polyethylene. 2 position.

FRONT ROLLER

Aluminum Wiehle roller standard; 2" (5.1 cm) diameter.

DIMENSIONS CERTIFICATION WARRANTY

Overall Length 54.25" (138 cm)

Overall Width 41" (104 cm)

Overall Height 41.5" (105 cm) w/o transport tires

Wheel Tread Weight 37.5" (95 cm) 230 lbs. (104 kg) w/o transport tires

Certified to meet ANSI specifications, B71.4-2004 and European Community (CE) specifications with required kits. Two-year limited warranty. Refer to the Operator’s Manual for further details. ** 04035

Greensmaster 1600 CARB (California Air Requirements Board)

GREENSMASTER 1600 ACCESSORIES STANDARD EQUIPMENT

ROLLER & ROLLER SCRAPER OPTIONS

TRACTION UNIT ACCESSORIES

93-9039

Narrow Wiehle Roller

95-0930

Full Roller

04062

93-9015

Low Cut Bedknife

112-9290

Wiehle Roller Scraper

112-9282

Operator Presence Bail Kit

65-8560

Front Roller Extension Kit

115-1886

Traction Slow Down Kit

107-1588

Rebuild Kit

65-9000

Clip Kit

99-4286

HOC Arm

04123

Wheel Kit

115-1880

Pulley Kit

04399

Turf Evaluator

REEL OPTION 95-0900

8-Blade Reel (standard)

112-9276

11-Blade Reel

BEDKNIFE & BEDBAR OPTIONS 94-5885

Tournament Bedknife

104-2646

High Cut Bedknife

107-8181

Fairway Bedknife

112-9275

Microcut Bedknife

112-9278-03

Aggressive Bedbar

99-4286

High Height of Cut Bar

94-9010

Height of Cut Adjustment Bar

112-9280-01

Bedbar - Standard (Red)

112-9278-03

Bedbar - Aggressive (Black)

99-4286

Extended Height of Cut Kit

GROOMER OPTIONS 04132

Groomer Reel

115-1600

Groomer Brush Assembly

110-2333

Groomer Blade

117-1399

Bolt

Light Kit

The Greensmaster 1600 is manufactured in Tomah, WI ISO 9002 Certified Plant.

TransPro 80 & 100 Safely and easily transports one or two walk greensmowers to and from the green.

TRANSPRO 80, MODEL 04238* Load Capacity Suspension Transport Speed

TRANSPRO 100, MODEL 04240*

400 lbs. (181.6 kg) including weight of trailer.

800 lbs. (363 kg) including weight of trailer.

Large low pressure tires (20 x 10-8). Maximum of 15 mph (24 km/h).

Ramp

Quick latch to secure loading ramp during transport. Rubber mats to protect front roller. Flat Ramp Kit and Rail and Ramp Kit optional.

Quick latch to secure loading ramp during transport. Rubber to protect front roller and provide safe surface during loading unloading of Greensmaster. Hole extrusions High Rail Ramp Kit optional.

Hitch

Pin type hitch is standard; tongue is 2.5" (6.4 cm) wide and adjustable in length (will accept standard ball hitch).

Pin type hitch is standard; tongue is 2" (5 cm) wide and adjustable in length (will accept standard ball hitch).

Towing

Designed to tow behind a utility vehicle; tongue height 7"-13" (18-33 cm); maximum tongue load 55 lbs. (25 kg). Incorporates a tongue stand and tongue lift handle. Hold down bails fold around mower tires to during transport. Drain holes in trailer bed for greensmower on trailer, allowing water and trailer floor.

Bed Finish Axles Dimensions

Rust/corrosion-resistant paint. Heavy-duty stub. Greaseable. Height: 19" (48.3 cm) Width: 62" (157.5 cm) Length: 81" (205.7 cm)

Height: 36" (91.4 cm) Width: 60.5" (153.7 cm) Length: 101" (256.5 cm)

Easily adjustable to fit all Toro walk greensmowers.

For 21" mowers with transport tires std. Kits available for conversion to fit 18" Rail kits available for 18 and 21" mowers. Not recommended for Greensmaster 1600.

TRANSPRO 80 ACCESSORIES

TRANSPRO 100 ACCESSORIES

04245 Flat Ramp Kit

04248 Rail Ramp Conversion Kit (TP100)

04247 Rail Ramp Kit

110-7355 18" Transport Wheel Conversion Kit

107-8188 Hitch Kit

110-7345 18" Rail Conversion Kit

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

Greensmaster 3150-Q ÂŽ

The next generation of the worldâ&#x20AC;&#x2122;s favorite riding greensmower.

Greensmaster 3150-Q Specifications* ®

GREENSMASTER 3150-Q, MODEL 04358 ENGINE FUEL CAPACITY TRACTION DRIVE GROUND SPEED TURF COMPACTION implement drive STEERING ELECTRICAL FEATURES CONTROLS/GAUGES TIRES/WHEELS/ PRESSURE BRAKES Hydraulic oil leak detection SOUND LEVEL OVERALL DIMENSIONS

18 hp (13.4 kW) Briggs & Stratton gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle. Air cooled, 34.8 cu. in. (570 cc). ®

7 gallon (26.5 liter) capacity; unleaded gasoline. 2 or 3WD, ROPS standard, hydrostatic piston pump closed loop system. Foot pedal forward and reverse; infinitely variable. Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster 3150-Q transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph (4.0 km/h) maximum. 8-10 psi (dependent on tire pressure) with operator and cutting units down. Single gear pump, mono valve block, series reel drive to 3 reel motors. Power steering. Adjustable steering wheel tilt and a 5-position steering arm tilt. 12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 16 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation. Raise/lower-mow lever (joystick). Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter. Hand operated throttle and choke. Mechanical engine speed control. Three tires: Three 18 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable with smooth tread. 8-12 psi front; 8-15 psi rear. Optional Traction Tire (2-ply): P/N 119-3516. Two 6" (15.2 cm) drum type. 7.5 gallon (28.4 liter) tank with internal baffle. 1.0 gallon (3.8 liter) auxiliary tank. Equipped with Turf Guardian™ leak detection system. 83 dB(A) at operator’s ear under normal conditions. Wheel Tread: 49.5" (149.9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69.75" (177 cm) w/reels, Height: 74.5" (189 cm), Weight: 1,087 lbs. (493 kg).

width of cut reel speed Backlapping

59" (150 cm)

cutting unit suspension

Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm. Baskets are supported by carrier frames that are ground following. Cutting unit floatation is unaffected by basket content. Grass baskets are all interchangeable and accessible from the front of the machine.

optional accessories

3WD kit, traction tire, thatching reels, spiker, tri-roller, turf evaluator, cutting reels, ROPS, light kit, oil cooler kit, arm rest speed control kit, LED light kit.

WARRANTY

Approximately 1975 RPM at 2850 engine RPM. Adjustable. Standard equipment.

Two-year limited warranty. Refer to the Operator’s Manual for further details. Briggs & Stratton provides a two-year commercial engine, and a lifetime Magnetron ignition warranty. ®

8 BLADE DPA CUTTING UNITS, 04618 11-BLADE DPA CUTTING UNITS, 04619 14-BLADE CUTTING UNITS, 04624 TRACTOR HEIGHT OF CUT (HOC) RANGE REEL WELDMENT REEL BEARINGS MAINTENANCE REEL DRIVE FRAME AGGRESSIVENESS BEDKNIFE BEDKNIFE ADJUSTMENT

These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex 33xx/34xx series). Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed. Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The reel is ground for diameter and concentricity, and backgrind. Two double row, self-aligning ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft with lock nut. Multiple seal barriers on both sides of bearing for added protection. Reel position maintained by a wave washer with no adjusting nut. No grease zerks, sealed bearing design eliminates daily maintenance. The reel weldment shaft is a 1.375" (35 mm) diameter tube with drive inserts permanently pressed in both ends. A replaceable floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring. The floating coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position. Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates. Aggressiveness stays constant throughout the life of the reel. Patented design. Replaceable single edged EdgeMax Microcut Bedknife is standard. TM

Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.

FRONT & REAR ROLLERS GRASS SHIELD

Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.

TOTAL WEIGHT

8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster 3150-Q is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster 3150-Q Specifications* (continued) 速

GREENSMASTER 3150-Q ACCESSORIES TRACTION UNIT ACCESSORIES

CUTTING UNIT & REEL OPTIONS

BEDKNIVE & BEDBAR OPTIONS

04476

3-Wheel Drive Kit

04618

8-Blade Cutting Unit

93-4262

Microcut Bedknife

04479

Thatching Reel (Set of 1)

04619

11-Blade Cutting Unit

93-4263

Tournament Bedknife

04494

Greens Spiker Kit

04624

14-Blade Cutting Unit

93-4264

Low Cut Bedknife

04495

Greens Tri-Roller Kit

119-4103

8-Blade Reel (Individual)

94-6392

High Cut Bedknife

117-6824

Thin dynaBLADE, (1.2mm Thickness)(Individual)

119-4104

11-Blade Reel (Individual)

63-8600

Fairway Bedknife

119-4105

14-Blade Reel (Individual)

108-4303

Extended Microcut Bedknife

108-4302

Extended Tournament Bedknife

115-1880

EdgeMax Microcut Bedknife (Standard on 04618, 04619, 04624)

115-1881

EdgeMax Tournament Bedknife

112-7475

EdgeMax Fairway Bedknife

99-3794-03

Aggressive Bedbar

120-9600

High Height of Cut Kit

119-1128

Regular dynaBlade, (2mm Thickness)(Individual)

117-6839

Replacement Kit, 1.2mm dynaBlade (36 Blades)

117-6840

Replacement Kit, 2mm dynaBlade (36 Blades)

30707

Armrest Kit

119-3516

Traction Tires

105-8336

Light Kit

105-8339

Hydraulic Oil Cooler Kit

117-2725

MVP Kit

ROLLER OPTIONS

SCRAPER OPTIONS 115-7374

Front Narrow Wiehle Roller Scraper

115-7375

Front Wide Wiehle Roller Scraper

115-7376

Front Full Roller Scraper

115-7377

Front Narrow Wiehle Roller Scraper Brush

115-7378

Front Wide Wiehle Roller Scraper Brush

115-7379

Front Full Roller Scraper Brush

115-7380

Front Narrow Wiehle Roller Scraper Comb

04626

Front Narrow Wiehle Roller (set of 3)

04627

Front Wide Wiehle Roller (set of 3)

115-7381

Front Wide Wiehle Roller Scraper Comb

04625

Front Full Roller (set of 3)

115-7382

Front Full Roller Scraper Comb

04628

Solid Steel Roller Kit (front Wiehle & rear steel rollers)

121-2260

Adjustable Rear Roller Scraper

04629

Anti-Bobbing Roller

04646

Spring Loaded Rear Roller Scraper (Set of 3)

71-1550

Cast Iron Rear Wiehle Roller

105-9561

Anti-Bobbing Roller Scraper Kit

107-3510

Steel Narrow Wiehle Roller

106-6945

Steel Rear Roller (standard)

GROOMER OPTIONS 04709

Groomer Drive (LH) (Set of 1)

04712

Groomer Reel, Spring Steel (Set of 1)

04713

Groomer Brush (Set of 1)

04726

Rotating Rear Roller Brush (LH) (Set of 1)

BIO-HYDRAULIC FLUID

114-4631

DPA Rear Roller Brush Adapter Kit

119-2157

112-9294

DPA Rear Roller Extension Kit

119-2158

Bio-Hydraulic Fluid, 5 gal. (18.9 L) Bio-Hydraulic Fluid, 55 gal. (208.2 L)

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster 3150 is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster 3250-D 速

Unmatched diesel power, innovative design and a lighter footprint make this the ideal greensmower for greens and surrounding areas.

Greensmaster 3250-D Specifications* ®

GREENSMASTER 3250-D, MODEL 04384 ENGINE FUEL CAPACITY TRACTION DRIVE GROUND SPEED TURF COMPACTION STEERING CONTROLS/GAUGES ELECTRICAL FEATURES SOUND LEVEL OVERALL DIMENSIONS

TIRES LEAK DETECTION Backlapping BRAKES SEAT optional accessories CERTIFICATION WARRANTY

Kubota 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 16.2 hp (12.1 kW) at 2400 rpm. Engine governed to 2710 rpm high idle, 1500 rpm low idle (no load). ®

6 gallons (22.7 liters). 2008 models Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petrol blend). Hydrostatic piston pump, closed loop system. Foot pedal forward and reverse; infinitely variable. Two front wheel orbit motors, 10.3 cu. in/rev displacement. 2 or 3 WD with ROPS. Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph (4.0 km/h) maximum. 10 psi (.68 bar) average at recommended minimum tire pressures, with a 200 lb. operator, and cutting units down. Power steering. Open center, non-load reacting steering valve with power beyond for raise/lower circuit and hydrostat charge circuit. 13.0" (33 cm) round steering wheel. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has 1.50" bore x 6.25" stroke with through shaft design for accurate straight line steering. Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter and 4 bulb warning cluster. Hand operated choke, throttle. Mechanical engine speed control. Water in fuel warning light. Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F (-17.7° C) and 85 minutes minimum reserve capacity at 85° F (29.4° C) 40 amp alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High temperature engine kill override switch. Harness terminals, fuse slot, and console switch location available for optional lights installation. 84 dBA at operator ear under normal conditions.

Width of Cut: Wheel Tread: Wheel Base: Overall Length (w/baskets): Overall Width:

59.0" (150 cm) 50.5" (128 cm) 48.6" (123 cm) 93.9" (238 cm) 68.0" (173 cm)

Overall Height: Net Weight (no fuel, no operator): Reel Speed:

77.5" (197 cm) 1,216 lbs. (552 kg) 1950 rpm minimum (Adj)

Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear. Turf Guardian™ optional. Standard equipment. 6" (15.2 cm) drum type mechanical with rack and pawl lock for parking. Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube mounted on the seat back for easy access. 3WD kit, spark arrestor, traction tire, thatching reels, spiker, tri-roller, turf evaluator, armrest kit, leak detector kit, hose adapter kit, light kit, oil cooler kit, radiator screen kit, ground-following suspension kit, 19" wheel weight kit, wheel weight kit, 400-hour maintenance kit, cutting reels. Certified to meet ANSI specification B71.4-2004 and European CE standards. Two-year limited warranty. Refer to the Operator’s Manual for further details. Briggs & Stratton provides a two-year commercial engine, and a lifetime Magnetron ignition warranty. ®

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

Greensmaster 3250-D Specifications* (continued) ®

Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.

FRONT & REAR ROLLERS GRASS SHIELD

Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.

TOTAL WEIGHT

8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.

GREENSMASTER 3250-D ACCESSORIES TRACTION UNIT ACCESSORIES

ROLLER OPTIONS

04477

3-Wheel Drive Kit

04626

Front Narrow Wiehle Roller (set of 3)

04479

Thatching Reel (Set of 1)

04627

Front Wide Wiehle Roller (set of 3)

04494

Greens Spiker Kit

04625

Front Full Roller (set of 3)

04495

Greens Tri-Roller Kit

117-6824

Thin dynaBLADE, (1.2mm Thickness) (Individual)

04628

Solid Steel Roller Kit (front Wiehle & rear steel rollers)

04629

119-1128

Regular dynaBlade, (2mm Thickness) (Individual)

117-6839

Replacement Kit, 1.2mm dynaBLADE (36 Blades)

117-6840

Replacement Kit, 2mm dynaBLADE (36 Blades)

30707

Armrest Kit

99-4506

Traction Tires

104-7701

Hydraulic Oil Cooler Kit

117-2721

MVP Kit

112-0279

Front Wheel Weight Kit

CUTTING UNIT & REEL OPTIONS 04618

8-Blade Cutting Unit

04619

11-Blade Cutting Unit

04624

14-Blade Cutting Unit

119-4103

8-Blade Reel (Individual)

119-4104

11-Blade Reel (Individual)

119-4105

14-Blade Reel (Individual)

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

BEDKNIVE & BEDBAR OPTIONS 93-4262

Microcut Bedknife

93-4263

Tournament Bedknife – Standard on 04618, 04619, 04624

93-4264

Low Cut Bedknife

94-6392

High Cut Bedknife

Anti-Bobbing Roller

63-8600

Fairway Bedknife

71-1550

Cast Iron Rear Wiehle Roller

108-4303

Extended Microcut Bedknife

107-3510

Steel Narrow Wiehle Roller

108-4302

Extended Tournament Bedknife

106-6945

Steel Rear Roller (Standard)

115-1880

114-4631

DPA Rear Roller Brush Adapter Kit

EdgeMax Microcut Bedknife (Standard on 04616)

112-9294

DPA Rear Roller Extension Kit

115-1881

EdgeMax Tournament Bedknife

114-4630

Rear Roller Adjustment Kit

112-7475

EdgeMax Fairway Bedknife

99-3794-03

Aggressive Bedbar

120-9600

High Height of Cut Kit

SCRAPER OPTIONS 115-7374

Front Narrow Wiehle Roller Scraper

GROOMER OPTIONS 04709

Groomer Drive (LH) (Set of 1)

04710

Groomer Drive (RH) (Set of 1)

04712

Groomer Reel, Spring Steel (Set of 1)

115-7375

Front Wide Wiehle Roller Scraper

115-7376

Front Full Roller Scraper

115-7377

Front Narrow Wiehle Roller Scraper Brush

115-7378

Front Wide Wiehle Roller Scraper Brush

04713

Groomer Brush (Set of 1)

115-7379

Front Full Roller Scraper Brush

04726

115-7380

Front Narrow Wiehle Roller Scraper Comb

Rotating Rear Roller Brush (LH) (Set of 1)

115-7381

Front Wide Wiehle Roller Scraper Comb

04724

Rotating Rear Roller Brush (LH) (Set of 1)

115-7382

Front Full Roller Scraper Comb

121-2260

Adjustable Rear Roller Scraper

04646

Spring Loaded Rear Roller Scraper (Set of 3)

105-9561

Anti-Bobbing Roller Scraper Kit

The Greensmaster 3250-D is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster TriFlex 3300/3320 Hybrid 3400/3420 Hybrid ™

The next generation of the world’s favorite riding greensmower.

Greensmaster TriFlex 3300/3320/3400/3420 Specifications* TM

GREENSMASTER 3300 TriFlex, MODEL 04510 ENGINE FUEL CAPACITY TRACTION DRIVE GROUND SPEED

CUTTING UNIT drive

STEERING

ELECTRICAL SYSTEM

Briggs & Stratton® Vanguard®, 21 HP (13.4 kW), 2-cylinder, air cooled, gasoline engine, governed to 2920 high idle, 1650 rpm low idle. Displacement: 38.3 cu-in. (627 cc)

Gauges TIRES/WHEELS/PRESSURE BRAKES Hydraulic oil

GREENSMASTER 3400 TriFlex, MODEL 04520

GREENSMASTER 3420 TriFlex Hybrid, MODEL 04540

Kubota D902, 23.5 HP (17.5 kW), 3-cylinder, liquid cooled, diesel engine, governed to 2880 high idle, 1560 rpm low idle. Displacement: 55.0 cu-in. (902 cc) Radiator: cooled with a 12-volt electric fan ®

6 gallons (22.7 liter) capacity. 2WD parallel hydrostatic or 3WD series-parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable. Forward-mowing speed is variable from 0-5 mph (0-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster TriFlex transport speed is 10 mph (16.1 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 3 mph (4.8 km/h) maximum.

Single gear pump, valve block, series reel drive to 3 reel motors.

48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V- 1100 watt brushless permanent magnet reel motors.

Single gear pump, valve block, series reel drive to 3 reel motors.

Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has a through shaft design for accurate straight line steering. 12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 ampsdraw. 50 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.

48-VOLT SYSTEM FOR ELECTRIC REELS CONTROLS

GREENSMASTER 3320 TriFlex Hybrid, MODEL 04530

Maintenance-free 12-volt battery with 585 minimum cold cranking amps at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C) 60 amp alternator, circuit fused at 60 amps. Ignition switch/key. Seat switch. High temperature engine shut down. Harness terminals, fuse slot, and console switch location available for optional lights installation.

4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis.

N/A

4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis.

N/A

Ignition: Off/Run/Start. Throttle: Low - High Idle. Choke (AC only): Open /Closes choke plate. Parking Brake: Off - On. Traction Pedal: Rev/Neutral/Forward Joystick: Raises/lowers reels also tap off feature for clean up pass. Functional Control Lever sets neutral/mow/transport limits for traction pedal. Diagnostic Light: Indicates system faults to assist in resolving issues. Fuel and hydraulic sight gauges, hour meter. Low oil pressure warning light.

Fuel and hydraulic sight gauges, hour meter. Low oil pressure warning light.

Fuel and hydraulic sight gauges, hour meter. Low oil pressure warning light, alternator warning light (on if not charging), glow plug indicator, high engine temperature.

Three, 19 x 10.5 x 8, 4-ply rating pneumatic tubeless and demountable. Smooth tread. Tire pressure recommended: 12 - 18 psi front and rear. Hand-actuated parking brake lever with two 6” (15.2 cm) diameter drum brakes mounted on the front wheel motors. 6.8 gallon (25.7 liter) tank

5.5 gallon (20.8 liter) tank

Equipped with Turf Guardian Leak Detection System. System sounds an alarm and turns on a warning light with the loss of 3 to 5 ounces of hydraulic oil.

Optional

6.8 gallon (25.7 liter) tank

5.5 gallon (20.8 liter) tank

leak detection SOUND LEVEL OVERALL DIMENSIONS Weight width of cut Ground clearance cutting unit Suspension quick connect cutting units reel speed Backlapping optional accessories CERTIFICATION WARRANTY

80 dB(A) at operator’s ear under normal conditions.

84 dB(A) at operator’s ear under normal conditions.

Wheel Tread: 50.5" (128.3 cm) Wheel Base: 47" (119 cm) Length: 98" (249 cm) Width: 70.62" (179 cm) w/reels Height: 80.83" (205 cm)

Wheel Tread: 50.5” (128.3 cm) Wheel Base: 47” (119 cm)Length: 98” (249 cm) Width: 70.84” (180 cm) w/reels Height: 80.83” (205 cm)

Wheel Tread: 50.5” (128.3 cm) Wheel Base: 48.6” (123 cm) Length: 98” (249 cm) Width: 70.62” (179 cm) w/reels Height: 80.83” (205 cm)

Wheel Tread: 50.5” (128.3 cm) Wheel Base: 48.6” (123 cm) Length: 98” (249 cm) Width: 70.84” (180 cm) w/reels Height: 80.83” (205 cm)

1161 lbs. (526 kg)

1257 lbs. (570 kg)

1286 lbs. (586 kg)

1406 lbs. (638 kg)

59" (150 cm) 4.5” (11.4 cm) Double A-arm suspension utilizing sealed ball joints allows free cutting unit motion in pitch, roll, and yaw. The basket is directly mounted to the cutting unit displacing weight evenly over both cutting unit rollers eliminating the carrier frame, roller and pull links. Quick connect/disconnect feature for both the reel drive motor and cutting unit. No tools required. Approximately 2050 RPM at 2850 engine RPM. Adjustable. Standard equipment. Canopy, verticutters, greens rollers, dethatchers, dew whip holder, oil cooler. Certified to meet ANSI specification B71.4 - 2004 and European CE standards. Two-year limited warranty. Refer to the Operator’s Manual for further details.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster TriFlex is manufactured in Tomah, WI ISO 9002 Certified Plant. ®

Greensmaster TriFlex 3300/3320/3400/3420 Accessories* TM

8-BLADE DPA CUTTING UNITS, 04613 DPA Cutting Units HEIGHT OF CUT (HOC) RANGE

11-BLADE DPA CUTTING UNITS, 04614

14-BLADE CUTTING UNITS, 04615

These cutting units will fit on the Greensmaster TriFlex Series. Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT

Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The reel is ground for diameter and concentricity, and backgrind.

REEL BEARINGS

Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/ slingers for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.

MAINTENANCE REEL DRIVE FRAME AGGRESSIVENESS BEDKNIFE

No grease zerks, sealed bearing design eliminates daily maintenance. The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert. Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates. Aggressiveness stays constant throughout the life of the reel. Patented design. Replaceable single edged, high carbon steel bedknife austempered to RC 55-58, fastened to a machined cast iron bedbar with 13 screws. EdgeMax Microcut Bedknife is standard on all cutting units. TM

BEDKNIFE ADJUSTMENT

Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.

FRONT & REAR ROLLERS

Front: Aluminum Wiehle , 2.5" (6.4 cm) diameter with sealed bearings and through-shaft. Option between full, narrow-spaced and wide-spaced roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft. ®

GRASS SHIELD

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.

TOTAL WEIGHT

8-blade: 80 lbs. (30.4 kg) with aluminum Wiehle Roller. 14-blade: 86 lbs. (39 kg) with aluminum Wiehle Roller.

11-blade: 83 lbs. (37.7 kg) with aluminum Wiehle Roller.

GREENSMASTER TRIFLEX ACCESSORIES TRIFLEX TRACTION UNIT ACCESSORIES

TRIFLEX DPA CUTTING UNITS

TRIFLEX DPA CUTTING UNIT ACCESSORIES

04714

3WD Kit

04613

8-Blade Cutting Unit

04710

Groomer Drive

04715

Leak Detector

04614

11-Blade Cutting Unit

04711

Groomer Reel, Carbide

04717

Light Kit

04615

14-Blade Cutting Unit

04712

Groomer Reel, Spring Steel

04718

Seat Kit, Standard

04713

Groomer Brush

04719

Seat Kit, Premium

04724

Rotating Rear Roller Brush

115-1880

EdgeMax Microcut Bedknife

115-1881

EdgeMax Tournament Bedknife

93-4262

Microcut Bedknife (HOC Range 1.58mm - 3.18mm)

93-4263

Tournament Bedknife (HOC Range 0.32mm - 6.35mm) Low Cut Bedknife (HOC Range 6.35mm and higher)

TRIFLEX DPA CUTTING UNIT ROLLERS 04625

Full Roller DPA

04626

Narrow Wiehle Roller DPA

04627

Wide Wiehle Roller DPA

92-7307

Armrest Kit - Standard

119-7105

Armrest Kit - Premium

119-1691

Hydraulic Oil Cooler Kit:Gas

117-9314

Hydraulic Oil Cooler Kit: Diesel

04628

Solid Steel Roller Kit (Front Wide Wiehle, Rear Full)

119-7129

2WD Weight Kit (ANSI compliance)

04629

Anti Bobbing Roller - DPA (Front and Rear)

120-5750

3WD Weight Kit (ANSI compliance) Spark Arrestor Kit (Gas)

Anti Bobbing Roller - Scraper Kit (Front and Rear)

93-4264

104-6540

107-9561

120-1951

Spark Arrestor Kit (Diesel)

114-4630

DPA Rear Roller Adjustment Kit

94-6392

Bedknife – High Cut

119-7138

Dew Whip Holder

71-1550

2” Rear Wiehle Roller (cast iron)

108-4303

Extended Microcut Bedknife

112-9294

Rear Roller Extension Kit

108-4302

Extended Tournament Bedknife

120-9600

High Height of Cut Kit (.35 - .94)

63-8600

Bedknife – Fairway

99-3794-03

DPA Bedbar (aggressive – optional)

106-2648-01

DPA Bedbar (less aggressive – standard equipment)

115-4510

Canopy

119-1715

Utility Bag Kit

OPTIONAL TRIFLEX ACCESSORIES 04720

Thatching Reel Kit - TriFlex

119-1128

Individual dynaBLADE, 2mm thickness

117-6824

Individual dynaBLADE, 1.2mm thickness

117-6839

Replacement dynaBLADE kit, 1.2mm thickness (36 blades)

117-6840

Replacement dynaBLADE kit, 2mm thickness (36 blades)

04722

Greens Tri-Roller Kit - TriFlex

04723

Greens Spiker Kit - TriFlex

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

TRIFLEX DPA CUTTING UNIT ROLLER SCRAPERS / BRUSHES / COMBS 04646

Rear Roller Scraper

115-7374

Front Wiehle Roller Scraper - Narrow

115-7375

Front Wiehle Roller Scraper - Wide

115-7376

Front Roller Scraper - Full

115-7377

Front Wiehle Roller Scraper Brush - Narrow

115-7378

Front Wiehle Roller Scraper Brush - Wide

115-7379

Front Roller Scraper Brush - Full

115-7380

Front Wiehle Roller Scraper Comb - Narrow

115-7381

Front Wiehle Roller Scraper Comb - Wide

115-7382

Front Roller Scraper Comb - Full

115-7383

Rear Roller Scraper - Adjustable

TRIFLEX SERVICE KITS 30042

400 hour filter Maintenance Kit Greensmaster TriFlex 3300

30045

400 hour filter Maintenance Kit Greensmaster TriFlex 3320

30043

400 hour filter Maintenance Kit Greensmaster TriFlex 3400

30047

400 hour filter Maintenance Kit Greensmaster TriFlex 3420

The Greensmaster TriFlex is manufactured in Tomah, WI ISO 9002 Certified Plant. ®