20 years of history in dental implants. In 2013, Neodent celebrates 20 years in business. A beautiful path where each step taken, each product released and each detail enhanced materialized the values of excellence and innovation. The dental implants industry has grown, taken new directions, new technologies, and Neodent has tread along, following all steps and having a direct participation in that evolution process, always bringing out the best for the market and for customers. Looking at the 20 years that have gone by and seeing all the changes reassures us that a lot has already been done, yet the best is still ahead of us.
Technical Guidelines
07
Morse Taper Line
18
Ti External Hex Line
50
II Plus Internal Hex Line
78
WS Morse Taper Line
96
Zygomatic Line
106
Orthodontic Anchoring and Bone Grafting
112
Neodent Techniques
122
Neodent Kits
144
Surgical Instruments
156
05
06
Technical Guidelines
07
Surface Constant evolution and guaranteed safety. Through years of intense research and development of new technologies, NEODENT has reached the current state-of-the-art in treating the surface of implants, the NeoPoros surface. Based on an abrasive particle jet concept, followed by acid subtraction, the NeoPoros surface promotes, through the use of controlled grain oxides, cavities in the implant surface, which are then made uniform by the acid subtraction (SLA) technique. The whole surfacing process is guaranteed by the automated control of time, speed, pressure and particle size. Several ongoing scientific studies to ensure that the NeoPoros surface is in constant evolution, providing you with greatly increased safety, are on go.
Scanning Electron Microsope Imaging of NeoPoros surface in different regions of Drive CM implant.
08
Scanning Electron Microscope imaging of NeoPoros surface in 2000x and 3000x magnifications. Controlled roughness to ensure pore size between 2.5 and 5.0Îźm through the whole implant surface.
Histological study of bone tissue response in contact with Morse Taper Implants with NeoPoros surface. Research conducted at the Bauru University Dentistry School in SĂŁo Paulo, as well as the Santa Catarina Federal University, and the Chieti-Pescara University in Italy.
09
acqua :: Hydrophilic Surface; :: Greater surface energy; :: Greater bone neoformation potential.
10
Acqua Acqua surface is obtained through a physiochemical process that provides an increase in the implant’s superficial energy, clinically resulting in a spreading of blood throughout the implant. NeoPoros
There is not only a reduction in the contact angle between liquid and surface and an increase in the titanium superficial energy, but also an advancement of stages in the bone matrix formation process, when compared to the NeoPoros surface**.
Contact angle > 30° (Hydrophobic Surface) NEOPOROS
Contact angle < 5° (Super-hydrophilic Surface) ACQUA
* Research conducted at the Mechanical Projects Laboratory at the Uberlandia Federal University School of Mechanical Engineering. ** Research conducted at the Dentistry Research Center – Biomechanics, Biomaterials and Cellular Biology at the Uberlandia Federal University Dentistry School and at the Bone & Mineralization Lab., University of North Carolina, Chapel Hill, USA.
11
New Implant Packaging Implant packages have been overhauled. Offering a concept that provides convenience and safety through all steps of the procedure, from storage to capture and to the implant transportation to the surgical alveolus. The new package eases identification of both the implant model as well as its diameter and length, regardless of its storage position, streamlining office procedures. Safety and convenience at armâ&#x20AC;&#x2122;s reach.
12
1
2
After breaking the sterility seal on the Blister, hold the primary package (crystal tube) with the non-dominant hand
The stand that holds the implant is removed
and open the lid.
from the crystal tube along with the lid.
3
4
With the non-dominant hand, press both sides of the stand, creating a gripping effect in order to secure the implant.
Keep pressing the stand and remove the lid.
5
6
Still pressing the stand, capture the implant with the contra-angle handpiece, moving the stand to find the perfect fit between handpiece and implant.
Transport the implant to the surgical alveolus
13
IMPLANT INDICATION TABLE According to Lekholm and Zarb bone classification (1985).
Bone type I
DriveCM DriveCM TitamaxCM Cortical
AlvimCM TitamaxWS Cortical TitamaxWS Medular DriveTi DriveTi TitamaxTi Cortical
AlvimTi TitamaxIIPlus AlvimIIPlus
14
Bone type II
Bone type III
Bone type IV
CONNECTIONS AND TORQUES
0.9
CM MORSE TAPER
WS
WS MORSE TAPER
Ti
EXTERNAL HEX
IIPlus INTERNAL HEX
CM Abutment CM and Exact Angled Mini Conical Abutment CM Mini Conical Abutment and CM Micro Abutment CM Universal Post CM Universal Post Passing Screw CM and Exact Angled Universal Post CM and Exact Anatomic Post Mini Ball Attachment Cylinders WS Abutment WS Mini Conical Abutment WS Universal Post Conical Abutment (Ø 4.3) and Slim Fit (Ø 4.1) Conical Abutment (Ø 5.0) Mini Conical Abutment (Ø 3.3 and Ø 4.3) Mini Conical Slim Fit Abutment (Ø 5.0) Mini Conical Slim Fit Abutment (Ø 4.1) Mini Angled Conical Abutment (Ø 4.1) SF Universal Post, Customizable and Angled UCLA (Ø3.3; Ø4.1; Ø4.3; Ø5.0) Mini Ball Attachment Cylinders II Plus Conical Abut. and II Plus Mini Conical Abutment II Plus Angled Conical Abutment II Plus Universal and Angled post II Plus UCLA Mini Ball Attachment Cylinders
1.2
Prosthetic Abutment
1.6
32N.cm 15N.cm 32N.cm 32N.cm 15N.cm 15N.cm 15N.cm 32N.cm 10N.cm 32N.cm 32N.cm 32N.cm 20N.cm 20N.cm 20N.cm 32N.cm 32N.cm 20N.cm 32N.cm 32N.cm 32N.cm 10N.cm 20N.cm 20N.cm 20N.cm 20N.cm 20N.cm 10N.cm
SELECTION OF PROSTHETIC ABUTMENTS ACCORDING TO ABUTMENT/IMPLANT INTERFACE Visit the website for more information www.neodent.com.br/us Work Method A . Over Intermediary
Prosthesis Type
1. Screw Retained
Multiple Prosthesis
Single Prosthesis
•Mini Conical Abutment •Angled Conical Abutment •Transepithelial Abutment •Micro Abutment
•Conical Abutment •CM Abutment
Multiple Prosthesis
Single Prosthesis
2. Cemented •Universal Post
•Anatomic Post •Universal Post •Customizable Post
B. Straight to Implant Multiple Prosthesis
Single Prosthesis
•UCLA
Multiple Prosthesis
Single Prosthesis
•UCLA •Customizable Post
15
APEX
IMPLANT BODY
PROSTHETIC INTERFACE
IMPLANT FEATURES
16
CM
HE
II Plus
Drive
Titamax
Alvim
Drive
Cortical
EX
WS
Alvim
17
Morse Taper Implant with sealing interface to optimize the bacterial sealing and peri-implant tissue health.
18
ImplantsCM Morse Taper
Morse Taper implants are now fitted with indexer.
New CM driver
Streamlined instalation that does not require assembler.
Exact line abutments, specific for CM Index implants.
:: Switching Platform Concept - Maintenance of cervical bone, greater width of soft tissue, with optimized aesthetics; :: Now with Hex Prosthetic Index; :: Reduced GAP (sealing interface); :: Stable Anti-Rotation Tightening; :: High mechanical resistance; :: Single prosthetic interface, regardless of implant diameter; :: The proper angle of NeoDent’s Morse Taper allows for a threaded cylindrical implant throughout, up to the cervical portion; :: Higher resistance when compared to external hex implants with regular platform.
Abutment Indication Table MORSE TAPER .5 m
ØI
mp
lan
t
m
Inner Thread Ø 1.8
MORSE TAPER Ø2
3.5, 3.75, 4.0, 4.3 and 5.0 mm
Screw Retained Prosthetics •CM Conical Abutment (single) •CM Mini Conical Abutment (multiple) •CM Angled Conical Abutment 17° and 30° (multiple) •CM Micro Abutment (multiple)
Cemented Prosthetics •CM Universal Angled Post 17° and 30° •CM Universal Post Passing Screw •CM Universal Post (single body) •Titanium Anatomic Post
Overdenture •CM Mini Ball Attachment
Protocol •CM Micro Abutment •CM Mini Conical Abutment •CM Angled Conical Abutment 17° and 30° •Cylinder and Distal Ext. Shaft Passive Fitting Technique • Castable Cylinder Mini Conical Abut. •Titanium Cylinder MiniConical Abut. •Brass Cylinder Mini Conical Abut.
19
CM Implants with Prosthetic Index
The hex prosthetic index streamlines the implant Instalation process, reduces surgery times, increases insertion torque resistance and allows the dentistry professional to install the prosthesis already foreseeing the crown positioning in relation to the implant, allowing for increased safety, speed and versatility in clinical and lab procedures.
Implant Capture and Transport Specific drivers to the implantâ&#x20AC;&#x2122;s hex prosthetic index, available for contra-angle, allow the capture of implants directly from the package. Replacing legacy assemblers with these Drivers ensures greater torque resistance, higher speed and safety to the procedure.
Each implant Instalation must be initiated with the contra-angle Drivers (whether in contraangle or adapted to the digital driver for contra-angle connections â&#x20AC;&#x201C; C.A.). When the implant is thus secured, the contra-angle driver should be replaced by the torque ratchet drivers to place the implant in the planned position. This procedure preserves both the contra-angle driver and the contra-angle bearings themselves, extending their life expectancy and preventing contra-angle drivers from locking inside the contra-angles.
Drivers Instalation drivers have six marks that coincide with the six flat sides of the implantâ&#x20AC;&#x2122;s hex prosthetic index. Upon Instalation, one of the driver marks should be in the vestibular position, in order to streamline the later prosthetic procedure.
20
CM Exact Line Besides a single CM interface for all implant diameters except for the WS and Zygomatic, CM implants now welcome another Abutments line, the EXACT LINE. These Abutmentes include, at the end of the cone, a hex index that allows positioning the prosthesis over the implant (prostethic indexing), adding even more versatility to the Morse Taper Line.
Conventional or Exact Abutments
Only conventional Abutments
Index Implant Versatility CM Implants with Prosthetic Index remain compatible with the entire CM prosthetic Abutments line which you are already familiar with, however the Exact line is compatible only with index CM implants.
Contact one of our expert assistants through Customer Service at +55 41 2169 1030 and discover the advantages of the new Morse Taper implants and the entire Exact prosthetic Abutments line.
CM Index Implants
CM Implant
21
DriveCM
PRODUCT FEATURES: :: Morse Taper Interface: :: Acqua Surface; :: Implant with Conical central core; :: Cervical Taper to reduce compressive tension on the bone; :: Double and progressive threads; :: Counterclockwise cutting chambers; :: Blade shaped apex thread; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Recommended for type III and IV bones and post-extraction; :: Single prosthetic interface for all implant diameters; :: For better prosthetic resolution, we recommend the Instalation of a 2mm infra-bone implant level; :: Drilling rotation: 500 - 800 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
3.5mm 4.3mm 5.0mm
22
Alvim 2.0
Alvim 3.5
Alvim 4.3
Alvim 5.0
M o r s e Ta p e r
8.0 mm
10.0 mm
11.5 mm
13.0 mm
16.0 mm
140.692
140.682
140.693
140.683
140.684
140.689
140.688
140.627
140.628
140.629
140.690
140.685
140.691
140.686
140.687
Ø 3.5
Ø 4.3
Ø 5.0
117.017
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
23
DriveCM
PRODUCT FEATURES: :: Implant with Conical central core; :: Morse Taper Interface: :: NeoPoros Surface; :: Cervical Taper to reduce compressive tension on the bone; :: Double and progressive threads; :: Counterclockwise cutting chambers; :: Blade shaped apex thread; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Recommended for type III and IV bones and post-extraction; :: Cover Screw not included; :: Single prosthetic interface for all implant diameters; :: For better prosthetic resolution, we recommend the Instalation of a 2mm infra-bone implant level; :: Drilling rotation: 500 - 800 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
3.5mm 4.3mm 5.0mm
24
Alvim 2.0
Alvim 3.5
Alvim 4.3
Alvim 5.0
M o r s e Ta p e r
8.0 mm
10.0 mm
11.5 mm
13.0 mm
16.0 mm
109.692
109.682
109.693
109.683
109.684
109.689
109.688
109.627
109.628
109.629
109.690
109.685
109.686
109.687
Ø 3.5
Ø 4.3
Ø 5.0
117.017
109.691
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
25
PRODUCT FEATURES: :: Cylinder body implant with Morse Taper interface; :: Acqua Surface; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Dual thread (faster Instalation with less trauma); :: High compacting power (bone expansion); :: Recommended for type III and IV bones and for narrow bone width areas due to sub-instrumentation; :: Cover screw not included; :: Single prosthetic interface for all implant diameters; :: Cervical diameter equal do implant body diameter; :: Ease of instrumentation when preparing the surgical alveolus; :: For better prosthetic resolution, we recommend the Instalation of a 2mm infra-bone implant; :: Drilling rotation: 800 - 1200 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Titamax 3.0
3.5mm 3.75mm 4.0mm
26
*Optional
M o r s e Ta p e r
9.0 mm
11.0 mm
13.0 mm
15.0 mm
17.0 mm
140.661
140.662
140.663
140.664
140.665
140.666
140.667
140.668
140.669
140.670
140.636
140.637
140.638
140.639
140.640
Ø 3.5
Ø 3.75
Ø 4.0
117.017
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
27
PRODUCT FEATURES: :: Cylinder body implant with Morse Taper interface; :: NeoPoros Surface; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Dual thread (faster Instalation with less trauma); :: High compacting power (bone expansion); :: Recommended for type III and IV bones and for narrow bone width areas due to sub-instrumentation; :: Cover screw not included; :: Single prosthetic interface for all implant diameters; :: Cervical diameter equal do implant body diameter; :: Ease of instrumentation when preparing the surgical alveolus; :: For better prosthetic resolution, we recommend the Instalation of a 2mm infra-bone implant; :: Drilling rotation: 800 - 1200 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Titamax 3.0
3.5mm 3.75mm 4.0mm
28
*Optional
M o r s e Ta p e r
9.0 mm
11.0 mm
13.0 mm
15.0 mm
17.0 mm
109.661
109.662
109.663
109.664
109.665
109.666
109.667
109.668
109.669
109.670
109.636
109.637
109.638
109.639
109.640
Ø 3.5
Ø 3.75
Ø 4.0
117.017
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
29
TitamaxCM Cortical PRODUCT FEATURES: :: Cylinder body implant with Morse Taper interface; :: NeoPoros Surface; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Dual thread (faster Instalation with less trauma); :: High cutting power; :: Recommended for bone types I and II and block grafting areas; :: Cover screw not included; :: Single prosthetic interface for all implant diameters; :: Cervical diameter equal do implant body diameter; :: Note the specific Pilot Drill (countersink function); :: For better prosthetic resolution, we recommend the Instalation of a 2mm infra-bone implant level; :: Drilling rotation: 800- 1200 rpm; :: Insertion rotation: 30 rpm.
NEW APEX
Seamless adaptation between drill and cortical implant
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Titamax 3.0
Titamax 3.15
Pilot CM 2.8 / 3.5
Titamax 3.3
Pilot CM 3 / 3.75
Pilot CM 3.3 / 4.0
Titamax 3.8
3.5mm 3.75mm 4.0mm 5.0mm
30
*Optional
Titamax 4.3
Pilot CM 4.3 / 5.0
M o r s e Ta p e r
7.0 mm
8.0 mm
9.0 mm
11.0 mm
13.0 mm
15.0 mm
17.0 mm
109.613
109.614
109.615
109.616
109.617
109.618
109.619
109.606
109.607
109.608
109.609
109.610
109.611
109.612
109.630
109.631
109.632
109.633
109.620
109.634
109.635
109.642
109.643
109.644
109.645
109.646
Ø 3.5
Ø 3.75
Ø 4.0
Ø 5.0
117.017
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
31
AlvimCM
PRODUCT FEATURES: :: Conical body implant with Morse Taper interface; :: NeoPoros Surface; :: Instalation is performed with CM drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Dual thread (faster Instalation with less trauma); :: Recommended for type III and IV bones and post-extraction; :: Cover screw not included; :: Cervical diameter equal do implant body diameter; :: Single prosthetic interface for all implant diameters; :: Note the specific Pilot Drill (countersink function); :: To increase prosthetic resolution, we recommend Instalation of a 2mm infra-bone implant level; :: Drilling rotation: 500 - 800 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
Alvim 2.0
Alvim 3.5
Pilot CM 2.8 / 3.5
Alvim 4.3
Pilot CM 3.6 / 4.3
Alvim 5.0
Pilot CM 4.3 / 5.0
3.5mm 4.3mm 5.0mm
32
*Optional
M o r s e Ta p e r
8.0 mm
10.0 mm
11.5 mm
13.0 mm
16.0 mm
109.657
109.658
109.659
109.621
109.660
109.647
109.648
109.649
109.622
109.651
109.652
109.653
109.654
109.655
109.656
Ø 3.5
Ø 4.3
Ø 5.0
117.017
CM cover screw :: Use 1.2 mm digital driver (104.007) for Instalation;
117.013
:: Do not exceed 10N.cm torque.
Healings :: Use 1.2 mm digital driver (104.007) for Instalation; :: Do not exceed 10N.cm torque.
Perfil
0.8 mm
1.5 mm
2.5 mm
3.5 mm
4.5 mm
5.5 mm
Ø 3.3
106.182
106.168
106.169
106.170
106.183
106.184
Ø 4.5
106.175
106.171
106.172
106.173
106.174
106.180
33
Demonstration sequence for
CM Abutment :: Minimum interocclusal space of 5.0mm from mucous level; :: Single prosthesis screw retained (Anti-rotation); :: Recommended for posterior regions; :: Consider additional 1.5 - 2.0mm of restoring material.
32
N.cm
CM Abutment
Connection for 1.6 Torque
Open Tray
Closed Tray
Torque Ratchet
CM Abutment Transfer
CM Abutment Protection Cylinder
Connection for 1.2mm Torque
10
CoCr Titanium
CM Abutment Analog
Castable
N.cm
CM Abutment Cylinder
34
Torque Ratchet
M o r s e Ta p e r
CM Abutment :: Note recommended torque in corresponding sequence.
CM Abutment Transfer :: Available in Titanium; :: Anti-rotational.
0.8 mm
1.5 mm 2.5 mm 3.5 mm 4.5 mm
5.5 mm
115.162 115.147 115.148 115.152 115.163 115.164
Open Tray
Closed Tray
108.039
108.040
CM Abutment Cylinder :: Available: Castable: For Casting; Titanium: For provisional prosthesis; CoCr: Overcasting. :: Screw included; :: Anti-rotational.
Castable
118.180
Titanium
118.179
CoCr
118.242
CM Abutment Analog 101.037
CM Abutment Protection Cylinder
CM Abutment Cylinder Screw :: Note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050);
Neotorque
106.102
Titanium
Neotorque
116.038
116.228
Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
35
Demonstration sequence for
CM Mini Conical Abutment CM Angled Conical Abutment :: Minimum interocclusal space of 4.4 mm from mucous level for straight Abutments; :: Multiple screw retained prosthesis; :: Consider additional 1.5 - 2.0mm of restoring material.
32
15
N.cm
N.cm
CM Mini Conical Abutment
Connection for Prosthetic Abutments
CM Mini Conical Angled Abutment (17째 and 30째)
Connection for 0.9 mm Torque
Open Tray
Closed Tray
Torque Ratchet
Mini Conical Abutment Transfer
Mini Conical Abutment Protection Cylinder
Torque Ratchet
Titanium
CoCr / Noble
10
N.cm
Castable
Mini Conical Abutment Analog
Mini Conical Abutment Cylinder
36
Connection for 1.2 mm Torque
M o r s e Ta p e r
CM Mini Conical Abutment :: Note recommended torque and sequence.
0.8 mm 1.5 mm 2.5 mm 3.5 mm 4.5 mm 5.5 mm 115.154 115.149 115.150
CM Angled Conical Abutment
17º 115.166 115.167 115.168 30º 115.169 115.170 115.171
Mini Conical Abutment Transfer
Open Tray
Closed Tray
Multifunctional
Ø 4.1
108.022
108.021
108.068
Short Screw
116.036
:: Available in Titanium; :: Rotational.
Mini Conical Abutment Cylinder
Castable Titanium Ø 4.1
118.112
118.113
Mini Conical Abutment Analog
Ø 4.1
Mini Conical Abutment Protection Cylinder
Ø 4.1
CM Mini Abutment Cylinder Screw :: Note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050);
Neotorque
115.160
1.5 mm 2.5 mm 3.5 mm
:: Height of CM angled prosthetic Abutments available on page 47.
:: Available in: Titanium: Provisional Prosthesis; CoCr: Overcasting; Castable: For Casting; Noble: Noble alloy with high melting point. :: Screw included; :: Rotational for multiple screw retained elements.
115.151 115.153
Noble
CoCr
Welding CoCr
118.206
118.209
118.210
101.020
106.054
Titanium
Neotorque
116.037
116.227
:: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
37
Demonstration sequence for
CM Micro Abutment :: Minimum interocclusal space of 3.5 mm from mucous level; :: Multiple screw retained prosthesis; :: Recommended for CM Implants close to each other; :: Consider additional 1.5 - 2.0mm of restoring material.
32
N.cm
CM Micro Abutment
Connection for Prosthetic Abutments
Open Tray
Torque Ratchet
CM Micro Abutment Transfer
Micro Abutment Protection Cylinder
Titanium
CoCr
Micro Abutment Analog
Micro Abutment Cylinder
38
Torque Ratchet
Castable
10
N.cm
Connection for 1.2 mm Torque
M o r s e Ta p e r
CM Micro Abutment :: Please note recommended torque and sequence.
0.8 mm 1.5 mm 2.5 mm 3.5 mm 4.5 mm 115.212 115.200 115.201
CM Micro Abutment Transfer
Rotational
:: Available in Titanium; :: Rotational.
CM Micro Abutment Cylinder :: Available in: Titanium: Provisional Prosthesis; CoCr: Overcasting; Castable; :: Screw included; :: Rotational for multiple screw retained elements.
Titanium 118.246
Castable
CoCr 118.245
101.057
CM Micro Abutment Protection Cylinder
106.199
:: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050);
Neotorque
108.070
CM Micro Abutment Analog
CM Abutment Cylinder Screw
115.202 115.213
118.247
Titanium
Neotorque
116.037
116.227
:: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
39
Demonstration sequence for
CM and Exact Anatomic Post :: Cemented single prosthesis; :: Customizable; :: Recommended for anterior regions.
Recommended sequence
CM Anatomic Post
Open Tray
15
N.cm
Closed Tray
Closed Exact Tray
Optional Sequence
CM Implant Transfer
CM Implant Analog
Connection for 0.9 mm Torque
Lab Stage
Torque Ratchet
Connection for 0.9 mm Torque
Customization, if needed
Conventional Castable
Torque Ratchet
Prosthesis Completed
Lab Stage
15
N.cm
40
M o r s e Ta p e r
CM Exact Anatomic Post :: Please note recommended torque; :: Exclusive Exact Abutment for CM Index implants; :: Height of anatomic prosthetic Abutments available on page 46.
CM Exact Anatomic Side Post
1.5 mm 2.5 mm 3.5 mm 114.422 114.423 114.424
1.5 mm 2.5 mm 3.5 mm 114.425 114.426 114.427
CM Anatomic Post
1.5 mm 2.5 mm 3.5 mm 114.328 114.329 114.330
CM Anatomic Side Post
1.5 mm 2.5 mm 3.5 mm 114.419 114.420 114.421
CM Implant Transfer :: Available in Titanium; :: Lengths: - Short: 15 mm; - Conventional: 20 mm.
CM Implant Analog
Conventional
Open Tray
Closed Tray
108.069
108.041
Short
108.065
Exact
108.076
101.058
41
Demonstration sequence for
CM Universal Post CM Universal Angled Post :: Cemented single prosthesis.
32
15
N.cm
N.cm
CM Universal Post
CM Universal Angled Post
Connection for 0.9 mm Torque
Connection for 1.2mm Torque
Torque Ratchet
CM Post Transfer
Universal Post Cylinder
42
Castable
Provisional
Alumina
CM Post Analog
M o r s e Ta p e r
Ø 3.3 Ø 4.5 Ø 3.3 Ø 4.5
6 mm
:: Please note sequence and torque control; :: Universal Post height available on page 46.
4 mm
CM Universal Post
0.8 mm 1.5 mm 2.5 mm 3.5 mm 4.5 mm
5.5 mm
114.129
114.077 114.078 114.079
114.136
114.137
114.131
114.080 114.081
114.082
114.142
114.143
114.130
114.086 114.087 114.088
114.139
114.140
114.132
114.083
114.145
114.146
CM Universal Angled Post
Ø 4.5
:: Available in polymer; :: Abutment with impression function to pHandleuce the prosthesis; :: For closed Tray technique (replacement); :: Select Transfer according to the Abutment to be Tray according to prosthetic planning; :: Anti-rotational.
Ø 3.3 Ø 4.5 Ø 3.3 Ø 4.5
Ø 3.3 Ø 4.5 Ø 3.3 Ø 4.5
6 mm
:: Available in: Acrylic: For provisional prosthesis; Alumina: For metal-free prosthesis; Castable. :: Compatible with all Universal Posts, when not modified.
4 mm
Universal Post Cylinder
Universal Post pack
Ø 3.3
:: Universal Post line Abutment pack, including Transfer and Castable and Provisional Cylinders.
Ø 4.5 Ø 3.3 Ø 4.5
Universal Post Analog
Ø 3.3 Ø 4.5 Ø 3.3 Ø 4.5
6 mm 4 mm 6 mm
Ø 3.3
4 mm
Ø 4.5 30º
6 mm
Ø 3.3
114.089
114.090 114.091
114.095 114.096
114.097
114.092 114.093
114.094
114.098 114.099
114.100
114.101 114.102
114.103
114.107 114.108
114.109
114.104 114.105
114.106
114.110 114.111
114.112
108.042 108.044 108.043 108.045
Alumina Castable
Provisional
118.186
118.181
118.192
118.188
118.183
118.194
118.187
118.182
118.193
118.189
118.184
118.195
4 mm
Ø 4.5
6 mm
Ø 3.3
4 mm
Ø 4.5 17º
6 mm
Ø 3.3
4 mm
1.5 mm 2.5 mm 3.5 mm
:: Please note sequence and torque control.
Universal Post Transfer
114.084 114.085
108.060 108.062 108.061 108.063
101.038 101.040 101.039 101.041
43
Demonstration sequence for
CM Exact Universal Post and CM Exact Angled Universal Post :: Cemented single prosthesis; :: Recommended for customization or laboratory use.
CM Exact Closed Tray Implant Transfer
CM Implant Analog
15
N.cm
CM Exact Universal Angled Post
CM Exact Universal Post
Connection for 0.9 mm Torque
Prosthesis Completed
Torque Ratchet
44
M o r s e Ta p e r
CM Exact Universal Post
Ø 3.3 Ø 4.5 Ø 3.3 Ø 4.5
4 mm
0.8 mm 1.5 mm 2.5 mm 3.5 mm 4.5 mm
6 mm
:: Please note recommended torque sequence; :: Abutment with passing screw; :: Exclusive Exact Abutment for CM Index implant.
114.408 114.360 114.361
114.362
114.363 114.364
114.410 114.357 114.358
114.359
114.372 114.373
114.409 114.366 114.367
114.368
114.369 114.370
114.411 114.340 114.341
114.342
114.375 114.376
CM Exact Universal Angled Post
Ø 3.3 Ø 4.5 Ø 3.3 30º
Ø 4.5 Ø 3.3 Ø 4.5
CM Implant Transfer
CM Implant Analog
Conventional
6 mm
Ø 4.5
4 mm
17º
6 mm
Ø 3.3
4 mm
1.5 mm 2.5 mm 3.5 mm
:: Please note recommended torque sequence; :: Height of CM angled prosthetic Abutments available on page 46.
:: Available in Titanium; :: Lengths: - Short: 15 mm; - Conventional: 20 mm.
5.5 mm
114.384
114.385 114.386
114.390 114.391
114.392
114.387 114.388 114.389 114.393 114.394 114.395 114.396 114.397 114.398 114.402 114.403 114.404 114.399 114.400 114.401 114.405 114.406 114.407
Open Tray
Closed Tray
108.069
108.041
Short
108.065
Exact
108.076
101.058
45
Universal, Altura do Munhão Anatomic Universal, and Lateral Anatômico Post e Lateral Height Universal Post
Transmucous
Cementable Profile 4 / 6 mm
Height 3.3 / 4.5 mm
Ø 3.3 mm
Ø 4.5 mm
4 mm
4 mm
6 mm
Ø 4.5 mm
6 mm
Ø 3.3 mm
Anatomic Post CM Anatomic Post
4.3 mm
5.3 mm
8 mm
Transmucous
Transmucous
46
4.7 mm
6.5 mm
5 mm
6 mm
6 mm
CM Anatomic Lateral Post
M o r s e Ta p e r
Heightdos Altura of CM Abutmentes Angled Prosthetic Protéticos Angulados CM Abutments
Universal Angled Post
4.90 5.80 5.90
3.90
3.50
4.80 3.50 4.90 3.50
2.50
2.90
3.80 2.50
1.50 1.50
5.20
3.50
3.50 3.50
4.50
Ø 4.5
4.20
2.50
2.50 3.20
1.50
30º
2.50
17º
1.50
Ø 3.3
Mini Conical Angled Abutment
3.90 2.50
1.50
4.90
3.50
30º
3.90
2.90 2.50
1.50
17º
47
Demonstration sequence for
CM Mini Ball Attachment
Protection Disc
Positioner
:: Recommended in-mouth capture, one Abutment at a time; :: Use of positioner is mandatory for capturing; :: O’ring with cylinder and protection disc included; :: Refer to demonstration sequence for CM Mini Ball Attachment on page 142.
32
N.cm CM Mini Ball Attachment
Connection for Prosthetic Abutments
Torque Ratchet
straight
7º
14º
Positioners
O’ring with Cylinder Protection Disc
48
M o r s e Ta p e r
CM Mini Ball Attachment
1.5 mm 2.5 mm 3.5 mm
4.5 mm
:: Please note sequence and recommended torque control
102.069
102.097
Castable Ball Attachment
102.070 102.071
102.078
:: Castable polymer; :: May be cemented on natural roots or waxed onto overdentures retaining bars.
Positioners :: Refer to sequence on page 142.
Protection Disc :: Package with 10 units.
O’ring with cylinder :: Protection Disc included; :: Titanium cylider and polymer o’ring.
straight , 7 0 e 14 0
102.076
102.077
102.073
Pink O’ring :: Available in polymer.
O’ring remover :: Digital Driver to remove the o’ring from the cylinder.
O’ring assembler
102.075
104.044
104.043
:: Digital Driver to replace the o’ring on the cylinder.
49
External Hex Solution for the limitation of External Hex Implants
50
External Hex
Implants
External Hex
Clip ensures greater safety in implant transport.
:: Ensures the external hex integrity; :: Maintains original rotational freedom; :: Increased practicality and safety; :: Increased mechanical resistance to insertion; :: Transport clip for safety in implant handling.
Internal torque area.
Abutment Indication Table He x2
1 mm
Ø3
.5
EXTERNAL HEX
mm
Inner Thread Ø 1.8
.37
mm
He x2
Ø 3.3
Screw Retained Prosthesis
Cemented Prosthesis
Overdenture
•Castable UCLA •CoCr UCLA
•Angled Post 17° •Castable UCLA •Titanium UCLA •CoCr UCLA
•SF Mini Conical Abutment (multiple) •Mini Conical Angled Abutment 17° and 30° (multiple) •SF Conical Abutment (single) •Castable UCLA •Noble UCLA •CoCr UCLA
•Angled Post 17° and 30° •Universal Post •Customizable Post •Castable UCLA •Noble UCLA •Titanium UCLA •CoCr UCLA
•Mini Ball Attachment
•Mini Conical Abutment (multiple) •Mini Conical Angled Abutment 17° and 30° (multiple) •Conical Abutment (single) •Castable UCLA •CoCr UCLA
•Angled Post 17° •Universal Post •Castable UCLA •Titanium UCLA •CoCr UCLA
•Mini Ball Attachment
Protocol
3.3 and 3.5 mm
.7 m
Inner Thread Ø 2.0
m
0.7 mm
mm
Hex
2.7
.3 m
m He x3
.3
1 mm
Ø5
.0 m
m
•Mini Conical Abutment •Mini Conical Angled Abutment 17° and 30° •Cylinder and Ext. Distal Bar Passive Fitting Technique •Castable Cylinder Mini Conical Abut. •Titanium Cylinder Mini Conical Abut. •Brass Cylinder Mini Conical Abut.
mm
1 mm
Ø4
3.75 and 4.0 mm
Inner Thread Ø 2.0
.1
Ø 4.3
Inner Thread Ø 2.5
Ø4
Ø 4.1
Ø 5.0
4.3 mm
•Mini Conical Abutment •Mini Conical Angled Abutment 17° and 30° •Cylinder and Ext. Distal Bar Passive Fitting Technique •Castable Cylinder Mini Conical Abut. •Titanium Cylinder Mini Conical Abut. •Brass Cylinder Mini Conical Abut.
mm
4.5 and 5.0 mm
•SF Mini Conical Abutment (multiple) •Mini Conical Angled Abutment 17° and 30° (multiple) •SF Conical Abutment (single) •Castable UCLA •CoCr UCLA
•Angled Post 17° •Customizable Post •Castable UCLA •Titanium UCLA •CoCr UCLA
•Mini Ball Attachment
•Mini Conical Abutment •Mini Conical Angled Abutment 17° and 30° •Cylinder and Ext. Distal Bar Passive Fitting Technique •Castable Cylinder Mini Conical Abut. •Titanium Cylinder Mini Conical Abut. •Brass Cylinder Mini Conical Abut.
51
PRODUCT FEATURES: :: External Hex Interface; :: Acqua Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Implant with Conical central core; :: Double and progressive threads; :: Counterclockwise cutting chambers; :: Blade shaped apex thread; :: Recommended for type III and IV bones and post-extraction; :: Drilling rotation: 500 - 800 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
3.5mm 4.3mm 5.0mm
52
Alvim 2.0
Alvim 3.5
Alvim 4.3
Alvim 5.0
External Hex
8.0 mm
10.0 mm
11.5 mm
13.0 mm
16.0 mm
140.752
140.753
140.754
140.755
140.756
140.757
140.758
140.759
140.760
140.761
140.762
140.763
140.764
140.765
140.766
Ø 3.5 Platform (3.3)
Ø 4.3 Platform (4.3)
Ø 5.0 Platform (5.0)
Cover screw 3.3 mm
117.001
4.3 mm
117.006
5.0 mm
117.003
:: Use a 0.9mm digital driver (104.039) to install the cover screw platform 3.3 and 4.3 and a 1.2mm digital driver (104.007) to install a cover screw platform 5.0;
Divergent Healings
Slim Fit Healings
2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.065
106.066
106.067
Ø 4.3
106.140
106.141
106.142
Ø 5.0
106.127
106.128
106.129
Ø 5.0
2.0 mm
3.0 mm
4.0 mm
106.195
106.196
106.197
Parallel Healings 2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.060
106.061
106.062
Ø 4.3
106.132
106.133
106.134
53
PRODUCT FEATURES: :: External Hex Interface; :: NeoPoros Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Implant with Conical central core; :: Double and progressive threads; :: Counterclockwise cutting chambers; :: Blade shaped apex thread; :: Recommended for type III and IV bones and post-extraction; :: Drilling rotation: 500 - 800 rpm; :: Insertion rotation: 30 rpm.
DRILL SEQUENCE Starter
3.5mm 4.3mm 5.0mm
54
Alvim 2.0
Alvim 3.5
Alvim 4.3
Alvim 5.0
External Hex
8.0 mm
10.0 mm
11.5 mm
13.0 mm
16.0 mm
109.752
109.753
109.754
109.755
109.756
109.757
109.758
109.759
109.760
109.761
109.762
109.763
109.764
109.765
109.766
Ø 3.5 Platform (3.3)
Ø 4.3 Platform (4.3)
Ø 5.0 Platform (5.0)
Cover screw
:: Use a 0.9mm digital driver (104.039) to install the cover screw platform 3.3 and 4.3 and a 1.2mm digital driver
3.3 mm
117.001
4.3 mm
117.006
5.0 mm
117.003
(104.007) to install a cover screw platform 5.0;
Divergent Healings
Slim Fit Healings
2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.065
106.066
106.067
Ø 4.3
106.140
106.141
106.142
Ø 5.0
106.127
106.128
106.129
Ø 5.0
2.0 mm
3.0 mm
4.0 mm
106.195
106.196
106.197
Parallel Healings 2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.060
106.061
106.062
Ø 4.3
106.132
106.133
106.134
55
PRODUCT FEATURES: :: Cylinder body implant with external hex interface; :: Acqua Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Instalation through implantâ&#x20AC;&#x2122;s internal hex, increasing mechanical resistance when high torques are applied, preserving the external hex integrity; :: Dual thread (faster Instalation with less trauma); :: High compacting power (bone expansion); :: Recommended for type III and IV bones; :: Cover screw not included; :: Ease of instrumentation when preparing the surgical alveolus; :: Drilling rotation: 800 - 1200 rpm; :: Instalation rotation: 30 rpm.
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Titamax 3.0
3.75mm 4.0mm
56
*Optional
External Hex
9.0 mm 11.0 mm 13.0 mm 15.0 mm 17.0 mm
Ø 3.75 Platform (4.1)
140.582
140.583
140.584
140.585
140.586
140.588
140.589
140.590
140.591
140.592
Ø 4.0
Platform (4.1)
:: Use a 0.9mm digital driver (104.039) to install the cover
Cover screw 4.1 mm
screw platform 4.1;
117.018
:: Do not exceed 10N.cm torque.
Divergent Healings
Ø 4.1
Slim Fit Healings
2.0 mm
3.0 mm
4.0 mm
106.092
106.093
106.094
Ø 4.1
2.0 mm
3.0 mm
4.0 mm
106.190
106.191
106.192
57
PRODUCT FEATURES: :: Cylinder body implant with external hex interface; :: NeoPoros Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Instalation through implantâ&#x20AC;&#x2122;s internal hex, increasing mechanical resistance when high torques are applied, preserving the external hex integrity; :: Dual thread (faster Instalation with less trauma); :: High compacting power (bone expansion); :: Recommended for type III and IV bones; :: Cover screw not included; :: Ease of instrumentation when preparing the surgical alveolus; :: Drilling rotation: 800 - 1200 rpm; :: Instalation rotation: 30 rpm.
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Titamax 3.0
3.75mm 4.0mm
58
*Optional
External Hex
9.0 mm 11.0 mm 13.0 mm 15.0 mm 17.0 mm
Ø 3.75 Platform (4.1)
109.582
109.583
109.584
109.585
109.586
109.588
109.589
109.590
109.591
109.592
Ø 4.0
Platform (4.1)
Cover screw 4.1 mm
:: Use a 0.9mm digital driver (104.039) to install the cover screw platform 4.1.
117.018
Divergent Healings
Ø 4.1
Slim Fit Healings
2.0 mm
3.0 mm
4.0 mm
106.092
106.093
106.094
Ø 4.1
2.0 mm
3.0 mm
4.0 mm
106.190
106.191
106.192
59
Cortical
PRODUCT FEATURES: :: Cylinder body implant with External Hex interface; :: NeoPoros Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Instalation through implantâ&#x20AC;&#x2122;s internal hex, increasing mechanical resistance when high torques are applied, preserving the external hex integrity; :: Dual thread (faster Instalation with less trauma); :: High cutting power; :: Recommended for bone types I and II and block grafting areas; :: Cover screw and assembler not included; :: Drilling rotation: 800 - 1200 rpm; :: Instalation rotation: 30 rpm.
NEW APEX
Seamless adaptation between drill and cortical implant
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 2.8
Countersink 3.5
Titamax 3.0
Titamax 3.15
Titamax 3.3
Pilot 3/3.75
Countersink 4.1 SF
Titamax 3.8
3.5mm 3.75mm 4.0mm 4.5mm 5.0mm
60
*Optional
Titamax 4.3
Countersink 5.0 SF
External Hex
7.0 mm
9.0 mm 11.0 mm 13.0 mm 15.0 mm
17.0 mm
Ø 3.3 Platform (3.3)
109.712
109.713
109.714
109.715
109.716
109.284
109.285
109.286
109.287
109.288
109.302
109.303
109.304
109.305
109.306
109.327
109.328
109.329
109.295
109.296
109.297
Ø 3.75 Platform (4.1)
Ø 4.0 Platform (4.1)
Ø 4.5 Platform (5.0)
Ø 5.0 Platform (5.0)
109.294
Cover screw
:: Use a 0.9mm digital driver (104.039) to install the cover screw platform 3.3 and 4.3 and a 1.2mm digital driver
3.3 mm
117.001
4.1 mm
117.018
5.0 mm
117.003
(104.007) to install a cover screw platform 5.0;
Divergent Healings
Slim Fit Healings
2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.065
106.066
106.067
Ø 4.1
106.092
106.093
106.094
Ø 5.0
106.127
106.128
106.129
2.0 mm
3.0 mm
4.0 mm
Ø 4.1
106.190
106.191
106.192
Ø 5.0
106.195
106.196
106.197
Parallel Healings
Ø 3.3
2.0 mm
3.0 mm
4.0 mm
106.060
106.061
106.062
61
PRODUCT FEATURES: :: Conical body implant with external hex interface; :: NeoPoros Surface; :: Instalation is performed with Ti drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Capture and Instalation with contra-angle or manual, without using assemblers (reduces surgery time); :: Instalation through implantâ&#x20AC;&#x2122;s internal hex, increasing mechanical resistance when high torques are applied, preserving the external hex integrity; :: Recommended for type III and IV bones and post-extraction; :: Cover screw and assembler not included; :: 1mm tall external hex; :: Drilling rotation: 500 - 800 rpm; :: Instalation rotation: 30 rpm.
DRILL SEQUENCE Starter
Alvim 2.0
Alvim 3.5
Countersink 3.5
Alvim 4.3
Countersink 4.3
Alvim 5.0
Countersink 5.0 SF
3.5mm 4.3mm 5.0mm
*Optional
62
External Hex
10.0 mm 13.0 mm 16.0 mm
Ø 3.5 Platform (3.3)
109.717
109.718
109.719
109.321
109.322
109.323
109.324
109.325
109.326
Ø 4.3 Platform (4.3)
Ø 5.0 Platform (5.0)
Cover screw 3.3 mm 4.3 mm 117.001
117.006
:: Use a 0.9mm digital driver (104.039) to install the cover screw 5.0 mm 117.003
platform 3.3 and 4.3 and a 1.2mm digital driver (104.007) to install a cover screw platform 5.0; :: Do not exceed 10N.cm torque.
Divergent Healings
Parallel Healings
2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.065
106.066
106.067
Ø 4.3
106.140
106.141
106.142
Ø 5.0
106.127
106.128
106.129
2.0 mm
3.0 mm
4.0 mm
Ø 3.3
106.060
106.061
106.062
Ø 4.3
106.132
106.133
106.134
Slim Fit Healings 2.0 mm 3.0 mm Ø 5.0
106.195
106.196
4.0 mm 106.197
63
SlimFIT External Hex
The SlimFIT line is Neodentâ&#x20AC;&#x2122;s innovation for External Hex Abutments, due to the rising parallel profile that minimizes bone removal.
SHORTENING OSTEOTOMY
CONVENTIONAL MINI CONICAL ABUTMENT WITH SF OSTEOTOMY
SF MINI CONICAL ABUTMENT WITH CONVENTIONAL OSTEOTOMY
Discover the benefits of the SlimFIT line and find out why certain details make all the difference: :: Ease of Fitting the prosthetic Abutment by reducing interference with the marginal bone; :: Preserves marginal bony plates; :: Optimizes Instalation; :: Ease of soft tissue synthesis procedures (suture) by increasing the mini conical abutment tapering.
64
External Hex
CONVENTIONAL OSTEOTOMY
SlimFIT OSTEOTOMY (REDUCED BONE REMOVAL)
CONVENTIONAL COUNTERSINK
NEW DRILL COUNTERSINK SlimFIT
For the SlimFit line, you need to use the new SF Countersink drill, with a new shape that reduces the drilling diameter and causes less trauma, preserving bone tissue.
Accomodation of Soft Tissue
Conventional rising profile
SlimFIT
intermediaries
accommodation
for
provide
peri-implant
excellent soft
tissue,
streamlining the prosthetic procedures in cases with immediate loading and long term tissue stabilization. SlimFIT rising profile
65
Demonstration sequence for
SF Conical Abutment :: Minimum interocclusal space of 6.1mm for platform 4.1, and 6.7mm for platform 5.0 from the mucous level; :: Single screw retained prosthesis (anti-rotational); :: Installed after using the Countersink drill, minimizing bone removal; :: SF Abutments improve tissue accommodation; :: Consider additional 1.5 - 2.0mm of restoring material.
20
N.cm SF Conical Abutment 4.1mm
Conical Abutment 4.3mm
Connection for Prosthetic Abutments
Conical Abutment 5.0mm
Connection for 1.6 mm Torque
Open Tray
Closed Tray
Torque Ratchet
Conical Abutment Transfer 4.1 and 5.0
Conical Abutment Analog 4.1 and 5.0
Conical Abutment Protection Cylinder 4.1 and 5.0
10
Torque Ratchet
Titanium
CoCr
Castable
N.cm
Conical Abutment Cylinder 4.1 and 5.0
66
Connection for 1.2 Torque
External Hex
:: Please note recommended torque and sequence.
Slim Fit
SF Conical Abutment
1 mm
2 mm
3 mm
Ø 4.1
115.192
115.193
115.194
Ø 4.3
115.051
115.052
115.053
Ø 5.0
115.007
115.008
115.009
Conical Abutment Transfer :: Anti-rotational.
Open Tray
Closed Tray
Ø 4.1
108.035
108.075
Ø 5.0
108.025
108.104
Conical Abutment Cylinder :: Available: Titanium: For provisional prosthesis; CoCr: Overcasting; Castable: For Casting. :: Screw included.
Conical Abutment Analog
Conical Abutment Protection Cylinder :: Used to protect the Abutment during prosthesis production; :: For Instalation, use a 1.2mm Digital Driver (104.007).
Castable
Titanium
CoCr
Ø 4.1
118.106
118.107
118.233
Ø 5.0
118.110
118.111
118.253
Ø 4.1
101.027
Ø 5.0
101.030
Ø 4.1
106.051
Ø 5.0
106.052
Conical Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Titanium
Neotorque
Ø 4.1
116.004
116.231
Ø 5.0
116.005
116.232
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
67
Demonstration sequence for
SF Mini Conical Abutment Angled Mini Conical Abutment :: Minimum interocclusal space of 4.4 mm for platform 4.1, and 4.8 mm for platform 5.0 from the mucous level; :: Multiple (rotational) screw retained prosthesis; :: Angled Mini Conical Abutment provides 12 fitting positions; :: Installed after using the Countersink drill, minimizing bone removal; :: SF Abutments improve tissue accommodation; :: Consider additional 1.5 - 2.0mm of restoring material.
20
32
N.cm
N.cm
Angled Mini Conical Abutment 17째 and 30째
SF Mini Conical Abutment 4.1mm
Connection for 1.2mm Torque
Connection for Prosthetic Abutments
20
N.cm
Mini Conical Abutment 3.3mm and 4.3mm
Connection for Prosthetic Abutments
32
N.cm
SF Mini Conical Abutment 5.0mm
Connection for 1.6mm Torque
Open Tray
Closed Tray
Torque Ratchet
Mini Conical Abutment Transfer 4.1 and 5.0
Mini Conical Abutment Analog 4.1 and 5.0
Torque Ratchet
10
Titanium
CoCr
Castable
Mini Conical Abutment Protection Cylinder 4.1 and 5.0
N.cm
Mini Conical Abutment Cylinder 4.1 and 5.0
68
Connection for 1.2mm Torque
External Hex SF Mini Conical Abutment
Slim Fit
Slim Fit
:: Please note sequence corresponding to the listed Abutment diameter and torque.
1 mm
2 mm
3 mm
Ø 3.3
115.134
115.135
115.136
Ø 4.1
115.187
115.188
115.189
115.190
Ø 4.3
115.054
115.055
115.056
115.057
Ø 5.0
115.197
115.198
115.199
Angled Mini Conical Abutment
2 mm
:: Please note recommended torque and sequence.
17º
115.137
115.138 115.139
Ø 4.1
115.084
115.074 115.075
Ø 4.3
115.076
115.077
115.078
Ø 5.0
115.094
115.095
115.096
115.140
115.141
115.111
115.112
Ø 4.3 Ø 5.0
Mini Conical Abutment Transfer
Open Tray
:: Available in Titanium; :: Rotational.
Mini Conical Abutment Cylinder :: Available in: Titanium: Provisional Prosthesis; CoCr: Overcasting; Castable: For Casting; Noble: Noble alloy with high melting point. :: Screw included; :: Rotational for multiple screw retained elements.
Mini Conical Abutment Analog
115.143
115.144
Closed Tray
Multifunctional
Ø 4.1
108.022
108.021
Ø 5.0
108.024
108.023
Short Screw
116.036
108.068
Castable
Titanium
Noble
CoCr
Welding CoCr
Ø 4.1
118.112
118.113
118.206
118.209
118.210
Ø 5.0
118.114
118.115
Ø 4.1
101.020
Ø 5.0
101.022
Mini Conical Abutment Protection Cylinder
Ø 4.1
106.054
:: For Instalation, use a 1.2mm Digital Driver (104.007).
Ø 5.0
106.055
Mini Conical Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
4 mm
Ø 3.3
Ø 4.1 30º
3 mm
4 mm
118.240
Titanium
Neotorque
Ø 4.1
116.037
116.227
Ø 5.0
116.038
116.228
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
69
Demonstration sequence for
SF Universal Post :: Cemented prosthesis; :: The Universal Post may be modified as needed, in this case, the prosthetic sequence cannot be used; :: Screw not included, for single elements select a Neotorque Screw.
SF Universal Post
32
N.cm Screw Neotorque
Connection for 1.2 Torque
Torque Ratchet
Post Transfer 4.5
Universal Post Cylinder 4.5
70
Castable
Provisional
Alumina
Post Analog 4.5
External Hex
2 mm
3 mm
4 mm
:: Compatible with External Hex platforms 4.1 and 4.3.
1 mm 114.428
114.429
114.430
6 mm
SF Universal Post
114.431
114.432
114.433
Ø 4.5
Hex Screw
Neotorque
:: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050). :: Compatible with External Hex platforms 4.1 and 4.3;
116.180
Titanium 116.002
4 mm
:: Available in polymer; :: Abutment with impression function to pHandleuce the prosthesis; :: For closed tray technique (replacement); :: Select Transfer according to the Abutment to be Cast according to prosthetic planning; :: Anti-rotational.
108.044
6 mm
Universal Post Transfer
108.045
4 mm
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
101.040
Ø 4.5
Universal Post Analog
6 mm
Ø 4.5
Universal Post Cylinder
6 mm
Ø 4.5
4 mm
Universal Post Assembly :: Universal Post line Abutment Kit, including Transfer and Castable and Provisional Cylinders.
4 mm
Alumina 118.188
Castable Provisional 118.183
118.194
118.189 118.184
118.195
108.062
Ø 4.5 6 mm
:: Available in: Acrylic: For provisional prosthesis; Alumina: For metal-free prosthesis; Castable. :: Compatible with all Universal Posts, when not modified.
101.041
108.063
71
Demonstration sequence for
Customizable Post Angled Post :: Cemented prosthesis; :: The Angled Post provides 12 fitting positions and includes a Titanium screw;
Open Tray
Closed Tray
:: Customizable Post does not include screw. We recommend using a Neotorque screw.
Transfer 3.3, 4.1, 4.3 and 5.0
Implant Analog 3.3mm, 4.1mm, 4.3mm and 5.0mm
Customizable Post 4.1 and 5.0mm
Angled Post (17째 and 30째) 3.3, 4.1, 4.3 and 5.0 mm
32
N.cm Neotorque Screw 4.1 and 5.0 mm
Titanium Screw
Connection for 1.2mm Torque
Torque Ratchet
72
External Hex
Angled Post :: Please note recommended torque and sequence; :: Abutment includes titanium screw; :: Anti-rotational.
17º
30º
Customizable Post :: Please note recommended torque and sequence; :: Screw not included; :: Anti-rotational.
2 mm
3 mm
4 mm
Ø 3.3
114.025
114.026
114.027
Ø 4.1
114.016
114.017
114.018
Ø 4.3
114.049
114.050
114.051
Ø 5.0
114.071
114.072
114.073
114.009
114.010
Ø 4.1
Ø 4.1 for Ø 5.0
114.029
Ø 4.1 for Ø 6.0
114.030
Ø 5.0 for Ø 6.0
114.035
Implant Transfer
Rotational
Anti-rotational
:: Available in Titanium.
Closed Tray
Open Tray
Ø 3.3
108.001
108.006
Ø 4.1
108.003
108.067 (SF)
Ø 4.3
108.029
108.034
Ø 5.0
108.013
108.011
Ø 3.3
108.002
Ø 4.1
108.066 (SF)
Ø 4.3
108.038
Ø 5.0
108.012
Hex Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Ø 3.3
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
Ø 4.3
Ø 4.1
Ø 5.0
Implant Analog
Neotorque
Titanium
116.188
116.001
116.180
116.002
116.189
116.003
Titanium
Brass
Ø 3.3
101.002
101.001
Ø 4.1
101.004
101.003
Ø 4.3
101.028
101.024
Ø 5.0
101.006
101.005
73
Demonstration sequence for
UCLA
:: For cemented or screw retained prosthesis; :: Presentation: - CoCr: Over Castable (screw not included); - Castable: (screw not included); - Titanium: Cemented or provisional prosthesis (screw not included); - Noble: Over Castable with high melting point alloys. Titanium (laboratory)
Open Tray
Closed Tray
and Neotorque screw included. :: For single elements, select a Neotorque screw.
Transfer 3.3, 4.1, 4.3 and 5.0mm
Analog 3.3, 4.1, 4.3 and 5.0mm
UCLA 3.3, 4.1, 4.3 and 5.0mm
32
N.cm Neotorque Screw
Connection for 1.2mm Torque
Torque Ratchet
74
External Hex
UCLA
Rotational
Anti-rotational
Cobalt-Chromium(Cocr)
Ø 3.3 Ø 4.1
118.212
Castable
Titanium
118.001
118.008
118.004
118.009
118.101
118.097 118.040
Ø 5.0
118.237
118.006
Ø 3.3
118.211
118.002
118.234
Ø 4.3 Ø 5.0
118.204
118.235
Ø 4.3
Ø 4.1
Noble
118.236
118.005
118.030
118.119
118.152
118.205
118.007
Implant Transfer
Rotational
Anti-rotational
:: Available in Titanium.
Closed Tray
Open Tray
Ø 3.3
108.001
108.006
Ø 4.1
108.003
108.067 (SF)
Ø 4.3
108.029
108.034
Ø 5.0
108.013
108.011
Ø 3.3
108.002
Ø 4.1
108.066 (SF)
Ø 4.3
108.038
Ø 5.0
108.012
Hex Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Ø 3.3
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
Ø 4.3
Ø 4.1
Ø 5.0
Implant Analog
Neotorque
Titanium
116.188
116.001
116.180
116.002
116.189
116.003
Titanium
Brass
Ø 3.3
101.002
101.001
Ø 4.1
101.004
101.003
Ø 4.3
101.028
101.024
Ø 5.0
101.006
101.005
75
Demonstration sequence for
Mini Ball Attachment
Protection Disc
Positioner
:: Recommended in-mouth capture, one Abutment at a time; :: Use of positioner is mandatory for capturing; :: Refer to demonstration sequence on page 142.
32
N.cm Mini Ball Attachment 4.1, 4.3 and 5.0mm
Connection for Prosthetic Abutments
Torque Ratchet
straight
7º
14º
Positioners
O’ring with Cylinder Protection Disc
76
External Hex
Mini Ball Attachment :: Please note sequence and recommended torque control.
Castable Ball Attachment
3 mm
2 mm
4 mm
Ø 4.1
102.060 102.061
102.062
Ø 4.3
102.063 102.064
102.065
Ø 5.0
102.066 102.067
102.068
102.078
:: Castable polymer; :: May be cemented on natural roots or waxed onto overdentures retaining bars.
Positioners :: Refer to sequence on page 142.
Protection Disc :: Package with 10 units.
O’ring with cylinder :: Protection Disc included; :: Titanium cylider and polymer o’ring.
straight , 7 0 e 14 0
102.076
102.077
102.073
Pink O’ring :: Available in polymer.
O’ring remover
102.075
104.044
:: Digital Driver to remove the O’ring from the cylinder.
O’ring Assembler
104.043
:: Digital Driver to replace the O’ring on the cylinder.
77
Internal Hex Internal interface that provides greater stability and resistance between implant and Abutment.
78
Internal Hex
ImplantsIIPlus
Internal Hex
Ø 5.0
Ø 3.8
Cervical micro-retentions.
Prosthetic Abutment with reduced platform in relation to implant (Switching Platform).
:: Prosthetic Abutments with reduced platform in relation to implant (Switching Platform); :: Clip Driver to increase safety when transporting and installing the implant; :: Cervical micro-retentions for bone tissue maintenance; :: Single prosthetic sequence, regardless of implant platform diameter.
Abutment Indication Table INTERNAL HEX INT
2.6
Im
pla
nt
Dia
me ter
mm
Inner Thread Ø 1.6
ER N 2.5 AL mm HEX
Implant Diameter 3.75, 4.3 and 5.0 mm
Prosthetic Platform Diameter
Screw Retained Prosthesis :: II Plus Mini Conical Abutment (multiple) :: II Plus CoCr UCLA (single) :: II Plus Conical Abutment (single) :: II Plus Angled Conical Abutment (multiple)
Cemented Prosthesis :: II Plus Universal Post :: II Plus Angled Post 17° and 30° :: II Plus CoCr UCLA (single) :: II Plus Titanium UCLA (single)
Overdenture :: II Plus Mini Ball Attachment
Protocol :: II Plus Angled Conical Abutment :: II Plus Mini Conical Abutment :: Cylinder and Distal Ext. Bar
Passive Fitting Technique :: Castable Cylinder Mini Conical Abut. :: Titanium Cylinder Mini Conical Abut. :: Brass Cylinder Mini Conical Abut.
4.3 and 5.0 mm
79
TitamaxIIPlus Cortical PRODUCT FEATURES: :: Cylinder body implant with internal hex interface; :: NeoPoros Surface; :: Instalation is performed with II Plus Drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Dual thread (faster Instalation with less trauma); :: High cutting power; :: Recommended for bone types I and II and block grafting areas; :: Cover screw not included; :: Single prosthetic interface for all implant diameters; :: Drilling rotation: 800 - 1200 rpm; :: Instalation rotation: 30 rpm.
NEW APEX
Seamless adaptation between drill and cortical implant
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 3.0
Titamax 3.15
Pilot 3/3.75
Countersink II 4.3
Titamax 3.8
Titamax 4.3
Countersink II 5.0
3.75mm 5.0mm
*Optional
80
Internal Hex
7.0 mm 9.0 mm 11.0 mm 13.0 mm 15.0 mm
Ø 3.75 Platform (4.3) 109.462
109.463
109.464
109.465
109.466
Ø 5.0
109.474
Cover screw
109.475
109.476
109.477
:: Use a 1.2 mm Digital Driver (104.007) to install the cover screw;
117.014
:: Do not exceed 10N.cm torque.
Healings 2.0 mm
3.0 mm
4.0 mm
106.176
106.177
106.178
81
AlvimIIPlus PRODUCT FEATURES: :: Conical body implant with internal hex interface; :: NeoPoros Surface; :: Instalation is performed with IIPlus Drivers (see page 160), allowing the implant capture directly from the package, offering greater safety and speed; :: Recommended for type III and IV bones and post-extraction; :: Cover screw not included; :: Single prosthetic interface for all implant diameters; :: Drilling rotation: 500 - 800 rpm; :: Instalation rotation: 30 rpm.
DRILL SEQUENCE Starter
Alvim 2.0
Alvim 3.5
Alvim 4.3
Countersink II 4.3
Alvim 5.0
Countersink II 5.0
4.3mm 5.0mm
*Optional
82
Internal Hex
10.0 mm 13.0 mm 16.0 mm
Ø 4.3 109.478
109.479
109.480
109.481
109.482
109.483
Ø 5.0
Cover screw 117.014
:: Use a 1.2 mm Digital Driver (104.007) to install the cover screw; :: Do not exceed 10N.cm torque.
Healings 2.0 mm
3.0 mm
4.0 mm
106.176
106.177
106.178
83
Demonstration sequence for
II Plus Conical Abutment II Plus Angled Conical Abutment :: Minimum interocclusal space of 6.1mm for the Straight Abutment, and 7.6 mm for the Angled Abutment from the mucous level; :: Screw retained prosthesis; :: Single Abutment for different II PLUS implant diameters (Ø 3.75, Ø 4.3 and Ø 5.0); Consider an additional 1.5 - 2.0mm of restoring material.
II Plus Conical Abutment (anti-rotational)
20
N.cm
Connection for Prosthetic Abutments
II Plus Angled Conical Abutment (Rotational)
Connection for 1.6 mm Torque
Open Tray
Closed Tray
Torque Ratchet
Conical Abutment Transfer
Conical Abutment Analog
Torque Ratchet
10
N.cm
Titanium
CoCr
Castable
Conical Abutment Protection Cylinder
Conical Abutment Cylinder
84
Connection for 1.2 Torque
Internal Hex
II Plus Conical Abutment :: Please note recommended torque and sequence; :: Single prosthesis (anti-rotational).
1.0 mm 115.184
2.0 mm
3.0 mm
115.185
115.186
II Plus Angled Conical Abutment 17°
2.0 mm
3.0 mm
4.0 mm
:: Please note recommended torque and sequence; :: Multiple Prosthesis (Rotational).
115.203
115.204
115.205
Anti-rotational
Conical Abutment Transfer
Open Tray
Closed Tray
108.035
108.075
108.020
108.018
Rotational
Ø 4.1
:: Available in: Titanium: for provisional prosthesis; CoCr: Overcasting; Castable: For Casting :: NeoTorque screw included.
Rotational
Ø 4.1
Anti-rotational
II Plus Conical Abutment Cylinder
Conical Abutment Analog
Conical Abutment Protection Cylinder
Conical Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Ø 4.1
CoCr
Castable
Titanium
118.106
118.107
118.233
118.104
118.105
118.232
101.027
Ø 4.1
106.051
Titanium
Neotorque
116.004
116.231
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
85
Demonstration sequence for
II Plus Mini Conical Abutment :: Minimum interocclusal space of 4.4 mm from mucous level; :: Multiple (rotational) screw retained prosthesis; :: Single Abutment for different II PLUS implant diameters (Ø 3.75, Ø 4.3 and Ø 5.0); :: Consider additional 1.5 - 2.0mm of restoring material.
20
N.cm
II Plus Mini Conical Abutment
Connection for Prosthetic Abutments
Open Tray
Closed Tray
Torque Ratchet
Mini Conical Abutment Transfer
Mini Conical Abutment Analog
Torque Ratchet
CoCr Titanium
Mini Conical Abutment Protection Cylinder
Castable
10
N.cm
Mini Conical Abutment Cylinder
86
Connection for 1.2mm Torque
Internal Hex
II Plus Mini Conical Abutment :: Please note recommended torque and sequence.
Mini Conical Abutment Transfer
Mini Conical Abutment Cylinder
Mini Conical Abutment Analog
Mini Conical Abutment Protection Cylinder
115.155
115.156
Ø 4.1
108.022
Short Screw
116.036
3 mm
4 mm
115.157 115.158
108.021
Castable Titanium Ø 4.1
118.112
Ø 4.1
Ø 4.1
Mini Conical Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
2 mm
Open Tray Closed Tray Multifunctional
:: Available in Titanium; :: Rotational.
:: Available in: Titanium: Provisional Prosthesis; CoCr: Ovecasting Castable: For Casting; Noble: Ovecasting with high melting point alloys. :: NeoTorque screw included (except for Castable cylinder); :: Rotational for multiple screw retained elements.
1 mm
Ø 4.1
118.113
Noble 118.206
CoCr 118.209
108.068
Welding CoCr 118.210
101.020
106.054
Titanium
Neotorque
116.037
116.227
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
87
Demonstration sequence for
II Plus Universal Post :: Cemented prosthesis; :: The Universal Post may be modified as needed, and in this case, the prosthetic sequence cannot be used; :: Single Abutment for different II PLUS implant diameters (Ø 3.75, Ø 4.3 and Ø 5.0); :: Screw not included, for single elements select a Neotorque Screw.
II Plus Universal Post
20
N.cm Neotorque Screw
Connection for 1.2 Torque
Torque Ratchet
Post Transfer 4.5
Universal Post Cylinder 4.5
88
Castable
Provisional
Alumina
Post Analog 4.5
Internal Hex
1 mm
2 mm
3 mm
4 mm
114.123
114.124
114.125
6 mm
Universal Post
114.126
114.127
114.128
:: Please note recommended torque and sequence.
Ø4.5
II Plus Hex Screw
Titanium
Neotorque
116.224
116.226
:: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050). Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
108.044
Ø 4.5 6 mm
:: Available in polymer; :: Abutment with Castable function to pHandleuce the prosthesis; :: For closed Tray technique (replacement); :: Select Transfer according to the Abutment to be Cast according to prosthetic planning; :: Anti-rotational.
4 mm
Universal Post Transfer
4 mm
Universal Post Analog
108.045
101.040
6 mm
Ø 4.5
6 mm
Ø 4.5
4 mm
Universal Post Cylinder :: Available in: Acrylic: For provisional prosthesis; Alumina: For metal-free prosthesis; Castable. :: Compatible with all Universal Posts, when not modfied.
108.062
Ø 4.5 6 mm
:: Universal Post Pack, includes Transfer, Castable and Provisional Cylinders.
4 mm
Universal Post Pack
101.041
108.063
Alumina
Castable Provisional
118.188
118.183
118.194
118.189
118.184
118.195
89
Demonstration sequence for
II Plus Angled Post
Open Tray
Closed Tray
:: Cemented prosthesis; :: Provides 6 fitting positions; :: Titanium screw included.
II Plus Transfer
II Plus Analog
20
N.cm
II Plus Angled Post
Connection for 1.2mm Torque
Torque Ratchet
90
Internal Hex
II Plus Angled Post :: Please note recommended torque and sequence; :: Anti-rotational.
17
0
2 mm
3 mm
4 mm
114.171
114.172
114.173
114.174
114.175
300
II Plus Implant Analog :: Available in brass.
Ă&#x2DC; 4.3
101.032
Ă&#x2DC; 5.0
101.034
Implant Transfer Anti-rotational
Closed Tray
108.046
Open Tray
108.047
91
Demonstration sequence for
II Plus UCLA :: Cemented or screw retained prosthesis; :: Presentation: - CoCr: Over Castable; - Titanium: Cemented or provisional prosthesis. :: Screw not included;
Open Tray
Closed Tray
:: For single elements, select a Neotorque screw.
II Plus Transfer
CoCr
Titanium
II Plus Analog
II Plus UCLA
20
N.cm Neotorque Screw
Connection for 1.2mm Torque
Torque Ratchet
92
Internal Hex
II Plus UCLA
118.185
Rotational
Anti-rotational
Titanium
II Plus Hex Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Cocr
118.214
118.213
Titanium
Neotorque
116.224
116.226
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
Implant Transfer :: Available in Titanium.
II Plus Implant Analog :: Available in brass.
Closed Tray
Open Tray
108.046
108.047
Ă&#x2DC; 4.3
101.032
Ă&#x2DC; 5.0
101.034
93
Demonstration sequence for
II Plus Mini Ball Attachment
Protection Disc
Positioner
:: Recommended in-mouth capture, one Abutment at a time; :: Use of positioner is mandatory for capturing; :: Refer to demonstration sequence on page 142.
20
N.cm II Plus Mini Ball Attachment
Connection for Prosthetic Abutments
Torque Ratchet
straight
7º
14º
Positioners
O’ring with Cylinder Protection Disc
94
Internal Hex
II Plus Mini Ball Attachment :: For Instalation, use a Prosthetic Abutment Connection (105.009); :: Please note recommended torque; :: For torque control, use Torque Ratchet (104.050).
Castable Ball Attachment
2 mm
Ø 4.1
102.090
3 mm 102.091
4 mm 102.092
102.078
:: Castable polymer; :: May be cemented on natural roots or waxed onto overdentures retaining bars.
Positioners :: Refer to sequence on page 142.
Protection Disc :: Package with 10 units.
O’ring with cylinder :: Protection Disc included; :: Titanium cylider and polymer O’ring
straight , 7 0 e 14 0
102.076
102.077
102.073
Pink O’ring :: Available in polymer.
O’ring remover
102.075
104.044
:: Digital Driver to remove the O’ring from the cylinder.
O’ring assembler
104.043
:: Digital Driver to replace the O’ring on the cylinder.
95
WS Morse Taper Neodent short implants (WS line) have a wide diameter and are the best prescription for upper and lower posterior regions.
96
ImplantsWS IMplante WS
Abutment Indication Table
Ø3
.0 m
Ø Im
m
Inner Thread Ø 1.8
MORSE TAPER WS MORSE TAPER AND ZYGOMATIC
Screw Retained Prosthesis
Cemented Prosthesis
•WS Abutment (single) •Mini WS Conical Abutment (multiple) •CM Transepithelial Abutment (multiple)
•WS Universal Post with Screw
Overdenture
Protocol •Mini WS Abutment Passive Fitting Technique •Castable Cylinder Mini Conical Abut. •Titanium Cylinder Mini Conical Abut. •Brass Cylinder Mini Conical Abut.
4.0, 5.0 and 6.0 mm
plan
t
97
TitamaxWS
PRODUCT FEATURES: :: Cylinder body implant with Morse Taper interface; :: NeoPoros Surface; :: Pre-assembled; :: Cover screw not included; :: Primary stability optimization; :: Excelent alternative for upper and lower posterior free extremity; :: Pre-assembled; :: Please note the specific Pilot Drill (countersink function); :: For the WS Medular Titamax Implant, a pilot drill is optional; :: Drilling rotation: 200 to 300 rpm; :: Insertion rotation: 30 rpm;
:: Exclusive Morse Taper prosthetic interface (same size as CM Zygomatic Implants).
DRILL SEQUENCE Starter
Titamax 2.0
Pilot 2/3
Titamax 3.0
Titamax 3.3
Pilot CM 3 / 3.75
Pilot CM 3.3 / 4.0
Titamax 3.8
Pilot CM 3.8 / 4.3
Titamax 4.3
Pilot CM 4.3 / 5.0
Pilot CM 4.3 / 5.3
4.0mm 5.0mm 6.0mm
*Mandatory for Cortical Implant and optional for Medular Implant
98
Titamax 5.3
Pilot CM 5.3 / 6.0
Implants WS
Cortical
Medular 5.0 mm
6.0 mm
Ø 4.0
5.0 mm
6.0 mm
109.578
109.579
109.580
109.581
Ø 4.0
109.604
109.605
Ø 5.0
Ø 5.0
109.574
109.575
109.576
109.577
Ø 6.0
WS Cover Screw 117.016
:: Use 1.2 mm Digital Driver (104.007) to install the cover screw; :: Do not exceed 10N.cm torque.
WS Healings 0.8 mm
1.5 mm
2.5 mm
3.5 mm
106.186
106.187
106.188
106.189
99
Demonstration sequence for
WS Abutment :: Minimum interocclusal space of 5.0mm from mucous level; :: Single prosthesis screw retained (Anti-rotation); :: Recommended for posterior regions; :: Consider additional 1.5 - 2.0mm of restoring material.
32
N.cm
WS Abutment
Connection for 1.6 torque
Open Tray
Closed Tray
Torque Ratchet
CM Abutment Transfer
CM Abutment Protection Cylinder
10
CoCr Titanium
CM Abutment Analog
Castable
N.cm
CM Abutment Cylinder
100
Torque Ratchet Connection for 1.2mm torque
Implants WS
WS Abutment :: Please note corresponding sequence and recommended torque.
CM Abutment Transfer :: Available in Titanium; :: Anti-rotational.
0.8 mm
1.5 mm 2.5 mm 3.5 mm
115.180 115.181 115.182 115.183
Open Tray
Closed Tray
108.039
108.040
CM Abutment Cylinder :: Available: Titanium: For prosionary prothesis; CoCr: OverCasting; Castable: For casting. :: Screw Included; :: Anti-rotational.
Castable
118.180
Titanium
118.179
CoCr
118.242
CM Abutment Analog 101.037
CM Abutment Protection Cylinder
CM Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050);
Neotorque
106.102
Titanium
Neotorque
116.038
116.228
:: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
101
Demonstration sequence for
WS Mini Conical Abutment :: Minimum interocclusal space of 4.4 mm from mucous level; :: Multiple screw retained prosthesis; :: Consider additional 1.5 - 2.0mm of restoring material.
32
N.cm
WS Mini Conical Abutment
Connection for Prosthetic Abutments
Open Tray
Closed Tray
Torque Ratchet
Mini Conical Abutment Transfer
Mini Conical Abutment Protection Cylinder
N.cm
Torque Ratchet
Titanium
CoCr / Noble
10
Castable
Mini Conical Abutment Analog
Mini Conical Abutment Cylinder
102
Connection for 1.2mm Torque
Implants WS
WS Mini Conical Abutment
0.8 mm 1.5 mm 2.5 mm 3.5 mm
:: Please note recommended torque and sequence.
115.176 115.177 115.178
Mini Conical Abutment Transfer :: Available in Titanium; :: Rotational.
Mini Conical Abutment Cylinder :: Available in: Titanium: Provisional Prosthesis; CoCr: Overcasting; Castable: For Casting; Noble: Noble alloy with high melting point. :: Screw included; :: Rotational for multiple screw retained elements.
Closed Tray
Multifunctional
Ø 4.1
108.022
108.021
108.068
Short Screw
116.036
118.112
118.113
Mini Conical Abutment Analog
Ø 4.1
Mini Conical Abutment Protection Cylinder
Ø 4.1
WS Mini Conical Abutment Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050);
Neotorque
Open Tray
Castable Titanium Ø 4.1
115.179
Noble
CoCr
Welding CoCr
118.206
118.209
118.210
101.020
106.054
Titanium
Neotorque
116.037
116.227
:: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
103
Demonstration sequence for
WS Universal Post :: Cemented prosthesis.
Optional Sequence
Recommended sequence
15
N.cm
WS Implant Transfer Closed Tray
WS Implant Analog
WS Post
Connection for 1.2mm torque
Lab Stage
Torque Ratchet
32
N.cm
WS Post
CM Post Transfer 4.5 Connection for 1.2mm torque
Universal Post Cylinder 4.5 Prosthesis Completed
104
Castable
Alumina
Provisional
CM Post Analog 4.5
Torque Ratchet
Implants WS
WS Universal Post
6 mm
Ø 4.5
4 mm
0.8 mm 1.5 mm 2.5 mm 3.5 mm
:: In two parts (body and screw); :: Please note recommended torque and sequence.
114.183
114.187 114.188
WS Implant Transfer
WS Analog
4 mm
108.044
6 mm
Ø 4.5
Alumina
Castable Provisional
4 mm
108.045
118.188
118.183
118.194
6 mm
Universal Post Cylinder
118.189
118.184
118.195
4 mm
108.062
6 mm
108.063
4 mm
101.040
6 mm
Ø 4.5
Universal Post Pack :: Universal Post Pack, including Transfer, Castable and Provisional Cylinders.
114.189 114.190
101.055
Universal Post Transfer
:: Available in: Acrylic: For provisional prosthesis; Alumina: For metal-free prosthesis; Castable: For Casting. :: Compatible with all Universal Posts, when modified.
114.186
108.064
:: Available in Titanium.
:: Available in polymer; :: Abutment with impression function to pHandleuce the prosthesis; :: For closed Tray technique (replacement); :: Select Transfer according to the Abutment to be Cast according to prosthetic planning; :: Anti-rotational.
114.184 114.185
101.041
Ø 4.5
Universal Post Analog Ø 4.5
105
Zygomatic CM and HE
106
Implants Zygomatic
Implants Zygomatic
m
0.7 m
Hex m
0m
ø 3.
mm 2.7
Ø
4.1
mm
107
Implants Zygomatic
PRODUCT FEATURES: :: Cylinder Implant; :: Clean surface; :: Pre-assembled; :: Cover screw not included; :: Dual thread in CM Zygomatic version; :: The use of the Transepithelial Abutment is recommended for the prosthetic interface;
:: Exclusive Morse Taper prosthetic interface (same size as WS Implants).
Length
Ă&#x2DC; 4.4mm
Ă&#x2DC; 3.9mm
108
Note: This technique requires specific accreditation. Information through +55 41 2169 1030
Implants Zygomatic
Morse Taper 30.0 mm
35.0 mm
40.0 mm
45.0 mm
47.5 mm
50.0 mm
52.5 mm
109.522
109.523
109.524
109.525
109.526
109.527
109.528
30.0 mm
35.0 mm
40.0 mm
45.0 mm
47.5 mm
50.0 mm
52.5 mm
109.460
109.450
109.451
109.452
109.461
109.453
109.454
External Hex
CM Zygomatic Cover screw
117.016
:: Use 1.2 mm Digital Driver (104.007) to install the cover screw; :: Do not exceed 10N.cm torque.
External Hex Cover Screw
117.018
:: Use 0.9 mm Digital Driver (104.039) to install the cover screw; :: Do not exceed 10N.cm torque.
109
Demonstration sequence for
Transepithelial Abutment :: Mini interocclusal space of 4.5mm; :: Multiple retained prothesis; :: Morse taper abutment
Morse Taper
32
N.cm
External Hex
compatible with Titamax WS Implant.
20
N.cm
Transepithelial Abutment
Connection for Prosthetic Abutments
Torque Ratchet
Transepitelial Abutment Transfer Open Tray
Transepitelial Abutment Analog
Transepitelial Abutment Protection Cylinder Torque Ratchet
Transepitelial Abutment Cylinder
110
CoCr
Castable
10
N.cm
Connection for 1.2mm Torque
Implants Zygomatic
External Hex Transepithelial Abutment :: For Instalation, use a Prosthetic Abutment Connection (105.009); :: For torque control, use Torque Ratchet (104.050).
Morse Taper Transepithelial Abutment
3 mm
4 mm
5 mm
115.023
115.024
115.025
3 mm
4 mm
5 mm
115.172
115.173
115.174
Transepithelial Abutment Transfer
108.026
:: DisponĂvel em Titanium; :: Rotational.
Transepithelial Abutment Cylinder :: Available in: Castable: For Casting; CoCr: Overcasting in several metals. :: Screw included.
Castable
CoCr
118.034
118.254
Transepithelial Abutment Analog
101.018
Transepithelial Abutment Protection Cylinder
106.056
Cylinder Screw :: Please note recommended torque; :: Use 1.2mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Titanium
Neotorque
116.004
116.231
Neotorque :: Application of a fine carbon-based coat that provides a lower friction coefficient, resulting in increased pre-load.
111
112
Implants Zygomatic
Orthodontic Anchoring
Bone Grafting
113
Orthodontic Anchoring PRODUCT FEATURES: :: Available in Titanium alloy as per ASTM-F136 ( V); :: Implants for orthodontic movement; :: Self-perforating; :: Collar height: - Low: 0 mm; - Medium: 1 mm. :: Torque resistance of up to 10 N.cm (Ă&#x2DC; 1.3 mm) and 20 N.cm (Ă&#x2DC; 1.6 mm).
1m m
Hole Diameter: 0.7mm
Hex Size: 2.7 mm
1
Orthodontic Anchoring Implant Package.
114
2
Removing the cap to access the implant.
Orthodontic Anchoring
Low Collar 5 mm
7 mm
9 mm
11 mm
109.484
109.485
109.486
109.701
109.493
109.494
109.495
5 mm
7 mm
9 mm
11 mm
109.487
109.488
109.489
109.496
109.497
109.498
Ø 1.3
Ø 1.6
Medium Collar
Ø 1.3
Ø 1.6
109.702
3
4
5
Implant capture with Orthodontic
Implant Instalation with Contra-Angle
Option of manual implant insertion using
Anchoring Contra-Angle Connection.
Connections (105.039 or 105.040).
Tuff Driver (104.033) or Ratchet and Ratchet
6
Implant installed.
Adapter for Contra-Angle Connections (105.025).
115
Bone Grafting PRODUCT FEATURES: :: Available in Titanium; :: Fixation of bone block; :: Self-perforating.
116
Expanded Head
Standard Head
Ø 1.5 mm
Ø 3.70mm
Ø 2.5 mm
Ø 2.0 mm
Ø 3.85 mm
Ø 3.0 mm
Bone Grafting
Standard Head 6 mm
8 mm
10 mm
12 mm
14 mm
116.194
116.196
116.198
116.199
116.200
116.203
116.205
116.207
116.209
8 mm
10 mm
12 mm
14 mm
116.210
116.211
116.212
116.213
116.214
116.215
116.216
Ø 1.5
Ø 2.0
Expanded Head
Ø 1.5
Ø 2.0
117
BONE GRAFTING AND ORTHODONTIC ANCHORING KIT FEATURES: :: Autoclavable polymer case
Note: Items that compose Neodent Kits are sold separately.
118
Bone Grafting
110.227 104.018 105.063 105.023 103.045 103.079 103.044 103.043 103.078 103.042 103.207 104.033 105.039 105.040 105.025
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Bone Grafting and Orthodontic Anchoring Case Bone Grafting Manual Driver Philips Connection for Manual Driver Philips Connection for Contra-Angle Drill 1.6 for Contra-Angle Drill 1.3 for Contra-Angle Drill 1.1 for Contra-Angle Drill 1.6 for Straight Piece Drill 1.3 for Straight Piece Drill 1.1 for Straight Piece Bone Grafting and Orthodontic Anchoring Puncture Anchoring Tuff Driver Anchoring Contra-Angle Connection - Long Anchoring Contra-Angle Connection - Short Ratchet Adapter for Contra-Angle Connections
X X X X X X X X X X X X X X X
X X X X X X X X X X X
Anchoring
Grafting
Contents
Complete
Bone Grafting and Orthodontic AnchoringKit X
X X X X X X X X
119
Drills for Orthodontic Anchoring :: Available in surgical steel; :: Recommended for type I and II bones; :: Marks refer to Implant length (5, 7, 9 and 11mm).
Ø 1.1mm
Ø 1.3mm
Ø 1.6mm
Straight Piece
103.042
103.078
103.043
Contra-Angle
103.044
103.079
103.045
11 mm 9 mm 7 mm 5 mm
Bone Grafting and Orthodontic Anchoring Puncture
103.207
:: Available in stainless steel; :: Initial cortical rupture.
Orthodontic Anchoring Adapter Connections
105.040
105.039
Short
Long
:: Connections for installing Anchoring Implants with Ratchet and Contra-Angle; :: Ratchet Adapter for Contra-Angle Connections (105.025).
120
105.025
Bone Grafting
Orthodontic Anchoring Tuff Driver
104.033
:: Available in stainless steel; :: Orthodontic Anchoring Implant manual Instalation.
Manual Driver 104.018
:: Assists in handling Philips Driver (105.063) and the Puncture for Bone Grafting and Orthodontic Anchoring Guide (103.207).
Philips Driver :: Available in stainless steel; :: Screw Instalation for bone grafting.
Manual Driver
105.063
Contra-Angle
105.023
121
122
Neodent Te c h n i q u e s
Neodent Techniques
123
BENEFITS :: Preservation of bone bed and adjacent tissues; :: Reduced surgery time; :: Practical and streamlined handling; :: Greater procedure safety and stability.
HOW DOES IT WORK? To perform a radicular extraction, you only need to turn the handle, making the wire rope attached to the tractor to remove the root, while preserving adjacent structures.
Extractor Tray
127.038
Contents 127.027 127.028 127.029 127.030 127.032 127.031 104.048 103.356 103.357
1 1 1 1 1 1 1 1 1
Tooth Extractor (with case) Tooth Extractor Tractor ø 2.10x10mm Tooth Extractor Tractor ø 1.60x16mm Tooth Extractor Tractor ø 1.60x10mm Tooth Extractor Tractor ø 2.10x16mm Tooth Extractor Wire Rope Tooth Extractor Digital Driver Twister Drill for Extractor 1.30mm Twister Drill for Extractor 1.80mm
Note: Items that compose the Tooth Extractor Kit are also sold separately.
124
Neodent Kits
Tooth Extractor TOOTH EXTRACTOR KIT FEATURES The Tooth Extractor provides practical and efficient handling. It is a solution that brings comfort, ease and precision to your practice. With simple and quick operation, the extractor allows extraction with less trauma in comparison with conventional techniques, preserving bone integrity in a safer surgical procedure.
DEMONSTRATION SEQUENCE 2
1
Tray preparation (127.038), Tray sold separately.
Residual tooth root preparation.
4
Instalation of Tractor to prepared area with Digital Driver.
3
Syndesmotomy.
5
Fitting the Tray to the Tooth Extractor.
6
Root removal by rotating the handle clockwise.
125
GUIDED SURGERY IN A SIMPLE, PRACTICAL AND ACCURATE WAY HELPING YOU IN ESSENTIAL STAGES NeoGuide has improved into a simplified service that helps you over essential stages of guided surgery, streamlining planning and providing better surgical and prosthetic predictability. With only 3 steps, we deliver to you a more accessible protocol:
Step 1: You send the tomography files from your patient to the NeoGuide Technology Center, where a team of professors will work in virtually placing implants and prosthetic abutments to develop a surgical guide. Step 2: You receive the virtual project by e-mail and, comfortably at home, your office or elsewhere, you approve the planning or suggest adjustments you consider necessary. Step 3: We deliver a surgical guide, just as you need it. With NeoGuide, the result is a quick and accurate treatment, valuing your time, work quality, and your patientsâ&#x20AC;&#x2122; comfort and safety.
NEOGUIDE ADVANTAGES: // Flapless surgery with reduced surgical trauma. // Guided implants from beginning to end. // Easy Instalation of prosthetic abutments // Prosthetic abutment system that allow passive prosthesis fitting. // Possibility of pHandleucing the prosthesis before the surgery. // Reduced surgery time. // Support and guidance for best technique.
126
UNDERSTANDING HOW NEOGUIDE WORKS
01 02
Tomographic Guide It is used to simulate the desired teeth position. Ideally, this guide is obtained by duplicating the wax teeth assembly.
Tomography Scanning is to obtain images of bone density, alveolar flap outlines and tomographic guide imaging.
03 04
The NeoGuide Center optimally positions implants, searching for the ideal location, and sends it back to the professional.
Planning Approval Using the free NeoGuide Light software, the professional reviews and approves the planning provided by the Neodent team.
05 06
Virtual Positioning
Surgical Guide Production Using state-of-the-art machinery, guides are pHandleuced with high accuracy and quality controle, using industry standards.
Guided Surgery With streamlined NeoGuide Kits, the work becomes of confidence and precision for flapless surgery.
127
NEOGUIDE KIT FEATURES: :: Technique-specific composition; :: Autoclavable polymer case :: Drivers, connections and surgery Instruments needed for the NeoGuide technique; :: Recommended technique for virtual planning and flapless surgery.
Note: Items that compose Neodent Kits are sold separately.
128
Implants
110.250 103.180 103.181 103.179 103.183 103.184 103.185 103.186 103.187 103.188 103.189 103.194 103.195 103.196 105.079 105.080 105.081 105.001 105.091 105.092 104.007 104.005 125.033 125.034 125.035 125.036 125.032 125.039 125.040 125.041 125.059 104.050 129.001 125.029 125.030 125.031
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 4 2 1 1 5 5 5
Neoguide Surgical Kit Case Neoguide Contra-Angle Mucous Extractor Neoguide Manual Mucous Extractor Neoguide Drill 1.3 Neoguide Drill 2.0 Neoguide Drill 2.8 Neoguide Drill 3.0 Neoguide Drill 3.3 Neoguide Pilot Drill 3.5 Neoguide Pilot Drill 3.75 Neoguide Pilot Drill 4.0 Neoguide Contra-Angle Narrow Mucous Extractor Neoguide Manual Narrow Mucous Extractor Neoguide Narrow Pilot Drill Neoguide CM 3.5 Contra-Angle Connection Neoguide CM 3.75 Contra-Angle Connection Neoguide CM 4.0 Contra-Angle Connection Ratchet Hex Connection Neoguide CM Narrow Contra-Angle Connection Neoguide CM Narrow Ratchet Connection Short 1.2 Digital Driver Digital Driver for Torque Connections Neoguide Drill Guide 2.0 Neoguide Drill Guide 2.8 Neoguide Drill Guide 3.0 Neoguide Drill Guide 3.3 Neoguide Guide Fastener Neoguide Narrow Drill Guide 2.0 Neoguide Narrow Drill Guide 2.8 Neoguide Guide Stabilizer Neoguide Narrow Guide Stabilizer Torque Ratchet Titanium Tweezers Neoguide Implant Guide 3.5 Neoguide Implant Guide 3.75 Neoguide Implant Guide 4.0
X X X X X X X X X X X
X X X X
X X X X X X X
X X X X X X
Complete
Contents
Regular
Zygomatic
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
129
Neoguide Drills :: Available in surgical steel; :: Twister Drill for ø1.3 and ø 2.0 and Tri-spade for other diameters; :: 1.3 drill for drilling through Surgical Guide tubes; :: Marks from 7 to 17mm.
Ø1.3
Ø2.0
Ø2.8
Ø3.0
Ø3.3
103.179
103.183
103.184
103.185
103.186
PLUS DRILLS: Application of a fine carbon-based coat that reduces the friction coefficient and the heat generated during osteotomy.
Guide Fastener
125.032
:: Available in Titanium; :: Pin that fastens the prototype surgical guide over the flap; :: Working length of 12mm and Ø1.3 mm.
Neoguide Pilot Drills :: Available in surgical steel with carbon coating to provide lower friction coefficients; :: Preparation of bone crest to settle the cervical Bone of Titamax CM Implants; :: Recommended for type I and II bones.
Stabilizer :: Available in Titanium; :: Aims to stabilize the prototype guide after the Instalation of each implant.
ø3.5
ø3.75
ø4.0
Neoguide Kit
103.187
103.188
103.189
Neoguide Kit Narrow
103.196
Neoguide Kit
125.041
Neoguide Kit Narrow
125.059
Mucous Extractor :: Available in surgical steel with carbon coating to provide lower friction coefficients; :: Guided circle incision for mucous removal; :: Rotating Mucous Extractor - Used with ContraAngle; :: Manual Mucous Extractor - Used manually with Digital Driver for Torque Connections (104.005); :: Also recommended as a punch.
Neoguide Implant Guide :: Available in Titanium; :: Guide for CM Implant Instalation using Neoguide Technique; :: Colors indicate the CM Implant diameters.
130
Contra-Angle
Manual
Neoguide Kit
103.180
103.181
Neoguide Kit Narrow
103.194
103.195
Ø3.5
Ø3.75
Ø4.0
125.029
125.030
125.031
Implants Zygomatic
Drill Guide :: Use the drill that matches the Surgical Guide diameter (colorcoded); :: Fitted to Surgical Guide ringlets; :: Colors indicate the CM Implant diameters.
ø2.0
ø2.8
ø3.0
ø3.3
Neoguide Kit
125.033
125.034
125.035
125.036
Neoguide Kit Narrow
125.039
125.040
3.5
3.75
4.0
Neoguide Kit
105.079
105.080
105.081
Neoguide Kit Narrow
105.091
125.040
Neoguide CM Contra-Angle Connection :: Available in Titanium; :: To insert implants using the motor and contra-angle.
Positioner Neoguide
101.054
:: Available in Titanium; :: Used with Mini Conical Abutment Analog to obtain a working model; :: Includes 3 pieces of 1mm high spacers; :: Technique for pHandleucing the prosthesis before the surgery.
Ratchet Hex Connection (Ratchet Driver Connection)
105.001
:: Available in surgical steel; :: Adaptation of hex assemblies; :: Fit in square ratchets; :: Silicone ring for better assembly tightening and transport.
131
CAD/CAM System
:: NEODENT and 3SHAPE PARTNERSHIP The 3shape scanner is the first step to use the Neoshape system, which has the accuracy of laser scanning as one of its highlights. With it, a Prosthesis Technician can scan impression models or Castables and, through a simple 3D modeling software, create pieces in a simple and intuitive way. Scanners D700, D500 e D810 provide micrometric precision by performing a laser reading on three different axes with no human contact. Professionals that purchase the system are provided with world-class tech support by the company and all technical information for the product to be used properly.
:: DENTAL DESIGNER SOFTWARE The Dental Designer software is versatile and intuitive. Its tools are straightforward and allow the handling of prosthetic structure drawings in a quick and efficient way. It allows customized anatomic adjustments such as: cementing space, coping width, adding or removing virtual waxing, abutment customization, among many others. As all planning happens virtually, the waste of time and materials is reduced.
132
:: NEODENT MILLING CENTER The milling process begins after a virtual image (previously designed by the prosthesis technician through the Dental Designer software) is sent to the CAM software, which will mathematically define the angles and axes to be designed on the material in order to reach a result exactly the same as planned. • micrometric adaptation; • optimization of production time; • automation of manual labor: virtual waxing; • laser scanning technology: accuracy and speed; • 5 axes milling: production faithful to CAD drawing; • raw materials with proven sources and quality.
Digital planning of high complexity dental prosthesis
:: AVAILABLE MATERIALS: - Cobalt-Chromium: ideal for metal-ceramic prosthesis. - Titanium: Recommended material for infrastructure in hybrid prosthesis. - Zircon: Aesthetics, high resistance, bio-compatibility. - E-max® CAD: Translucent, resistant, aesthetic, and easy to use.
133
The Neoshape System comprises new industry technologies to ensure the accuracy and quality in pHandleucing several prosthetic techniques available in the marketplace. This news widens horizons, offering excellence, adaptation, precision and aesthetics in a customized way with digital planning.
The Neoshape system offers, along with its 3D modeling software, an extensive library of prosthetic interfaces, allowing the prosthetic to pHandleuce customized structures over any Neodent implant or prosthetic abutment, with the same quality and adaptation accuracy of a standard abutment.
With that, the prosthesis technician uses the computer screen to plan in three dimensions all aesthetic and functional details of different prosthetic resolutions in common lab tasks.
Regardless of the material chosen to pHandleuce the prosthesis, the mechanical properties and quality warranty are reassured by world-class quality and controlled source raw materials, reinforcing our ethical commitment.
After the virtual waxing is completed, a digital file is forwarded online to the Neodent Milling Center. There, the information received from each case is managed. Next, the file is forwarded to state-of-the-art equipment that accurately repHandleuce the 3D drawings through milling, ensuring a precise adaptation and finishing.
NEODENT TASK PROSTHESIS TECHNICIAN TASK
PROSTHESIS TECHNICIAN TASK
PROSTHESIS TECHNICIAN TASK
DENTIST TASK
4. Production of customized part at the Neodent Milling Center
2. Scanning
3. CAD Modeling in 3D planning software 5. Prosthesis completed with porcelain application 1. Patient
134
STEP BY STEP TECHNIQUE
2
1
Castable of the elements to be restored and antagonist arc.
For overdenture work, the impression model must be dried and with preparation edges exposed and delimited. For implant works, the model must be hollow, with artificial gums.
4
3
Virtual planning.
Scanning the working model and antagonist.
5
Indutrial milling. Micrometric level quality control.
6
Different technique and material possibilities.
135
Demonstration sequence for
Passive Fitting Technique that allows passive Fitting, with no need for welding through cementing the Titanium cylinder to the metal structure. Used for multiple prostheses and reduces laboratory work times.
136
Neodent Te c h n i q u e s
Mini Conical Abutment Passive Fitting Cylinders :: Brass and Titanium cylinders include screw; :: For Instalation, use 1.2 mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
CM Micro Abutment Passive Fitting Cylinders :: Brass and Titanium cylinders include screw; :: For Instalation, use 1.2 mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Transepithelial Abutment Passive Fitting Cylinders :: Brass and Titanium cylinders include screw; :: For Instalation, use 1.2 mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
GT Passive Fitting Cylinders :: Brass and Titanium cylinders include screw; :: For Instalation, use 1.2 mm torque connection (105.005); :: For torque control, use Torque Ratchet (104.050).
Castable
Brass
Titanium
ø4.1
118.083
118.081
118.082
ø5.0
118.089
118.087
118.088
Castable
Brass
Titanium
118.250
118.248
118.249
Castable
Brass
Titanium
118.086
118.084
118.085
Castable
Brass
Titanium
118.174
118.173
118.172
Passive Fitting Work Screw
4.1 mm
5.0 mm
:: For laboratory use.
116.086
116.087
137
Demonstration sequence for
Passive Fitting Normalization of alveolar flaps.
Instalation of 5 Titamax Cortical CM Implants Ă&#x2DC;3.75.
Instalation of square transfers, replaced by short screws (Mini conical Abutment cylinder screw) and transfers joined with acrylic resin.
Removal of MultiFuncional Guide and Instalation of Mini Conical Abutment analogs to the transfers.
Castable Passive Fitting Cylinder, Brass Passive Fitting Cylinder, grooved Titanium Passive Fitting Cylinder with lower dimension than the brass, which compensates hiring the mill.
138
1
3
5
7
9
Surgical drilling completed, obtaining adequate distance from Distal implant in relation to the mental foramen with 7mm flag.
Instalation of CM Mini Conical Abutments.
Positioning of Multifunctional Guide to obtain intermaxillary ratios. Joining transfers with acrylic resin. After joining, liquid silicone is injected for impression of soft tissues.
Working model with artificial gum.
2
4
6
8
Neodent Te c h n i q u e s
10
Brass Cylinders are placed over analogs, Then Castable Cylinders are fixed by working screws.
11
Fused infrastructure.
13
12
14
Please note cementing area.
15
Castable ring with waxed infrastructure.
Adapting the infrastructure over the model.
Cementing with Panavia速 (Kuraray Med. Inc. Tokio-Japan) the structure over the Titanium cylinders.
Final inside-mouth view.
16
139
Demonstration sequence for
Distal Bar
:: Technique used to ease mandible rehabilitation, through a provisional protocol-type prosthesis supported by implants.
Distal Bar Cylinder :: Available in Titanium; :: Retainers to ease joining with acrylic resin; :: Recommended torque: 10 N.cm; :: For torque, use 1.2mm torque connection (105.005).
Mini Abutment Ø 4.1
118.169
Ø 5.0
118.170
GT
118.171
Distal Bar :: Recommended for distal Implants to reinforce the Cantilever.
Mini Abutment Ø 4.1
125.011
Ø 5.0
125.012
GT
125.023
Polish protector :: Available in surgical steel; :: Recommended for Conical Transfer (used in closed tray technique).
140
123.008
123.009
Neodent Te c h n i q u e s
GT Implants installed.
2
1
3
5
7
9
11
Instalation of cylinders to central Implants and Distal Bar to posterior Implants.
Placement of rubber dike over cylinders to protect soft tissue.
Applying acrylic resin between cylinders.
Removal of inferior prosthesis after resin is polymerized, cylinders already captured.
Provisional implantsupported prosthesis completed.
4
6
8
10
12
Prosthesis wearing, keeping posterior region integrity.
Proof of inferior prosthesis wearing (centered occlusion position, no interference on cylinders).
Applying selfpolymerizing acrylic resin on cylinders.
Applying to worn area in lower prosthesis, repositioning inside mouth, patient in occlusion until total polymerization.
Wearing, finishing and polishing inferior prosthesis with polishing protectors.
Final posterior insidemouth view.
141
Demonstration sequence for
Mini Ball Attachment
142
Neodent Te c h n i q u e s
1
Production of new total prosthesis.
Implants installed.
2
Abutments.
4
3
5
Using positioners to correct paralleling between Implants and determine the right distance between o’ring and Attachment.
6
Placement of o’rings.
8
7
9
Prosthesis proof to verify adaptation without interference.
Placement of protection discs.
Lower view of relief performed.
First O’ring captured.
10
Side view of assembly.
Second o’ring captured.
11
Ball Attachments installed.
12
143
144
Implants Zygomatic
Neodent Kits Paralleling positioners are color-coded and numbered to show the exact implant size to be used.
Surgical and Prosthetic Ratchet (single model) can be disassembled and has torque control.
Surgical Tweezer with automatic implant locking and millimeter scale for reference during procedures.
STERILIZATION
Sterilize on the day before or the day of the procedure. We recommend, preferentially, the sterilization method by steam autoclaving, including the parameters and procedures set forth in regulation BS EN ISO 17665-1: Sterilization of health care products. Moist heat. Requirements for the development, validation and routine control of a sterilization process for medical devices; or to proceed according to the autoclave manufacturer’s instruction manual. WARNING: KITS ARE DAMAGED IF SEALED WITH DUCT TAPE. DO NOT STERILIZE POLYMER PRODUCTS USING STOVE. STERILIZATION PERIOD: 7 to 15 days, if stored in a clean, dry environment protected from sunlight.
CLEANING
Neodent Kits and Surgical Instruments must be properly cleaned after each use. Do not leave them in contact with humidity for long periods. 1st step: Disassemble parts (if applicable). 2nd step: Completely immerse the part in 10% enzymatic detergent solution. 3rd step: Wash in ultrasound cleaner for about 10 minutes. 4th step: Rinse with abundant distilled water to completely remove solution residues, even by brushing, if needed. 5th step: Dry with paper towels or air blower. 6th step: Perform a visual inspection to check for flaws in the cleaning process. If the part is dirty, it should be immersed again in detergent – steps 1 and 2 – and, if needed, clean with a nylon brush (repeat the rinse and dry sequence). 7th step: Select the package according to the sterilization process. Prefer self-sealing packages with surgical paper and film blade. IMPORTANT: Never store the material unless completely dry. Drying is extremely important to prevent oxidation. WARNING: Do not use (nonenzymatic) descaler products, as they tend to darken parts and also cause oxidation. The use of enzymatic fluid in higher concentration than 10%, as well as drying parts that contain residual cleaning solution, favors oxidation and should be avoided.
145
Note: Items that compose the Surgical Kit are sold separately. Below, we suggest three Surgical Kit setups: Starter, Intermediate and Advanced.
146
Neodent
Contents 110.251 103.170 103.171 103.162 103.213 103.163 103.164 103.165 103.166 103.167 103.168 103.172 103.173 103.174 103.366 103.239 103.211 103.242 103.216 103.217 103.218 103.219 103.220 103.091 105.047 105.045 105.046 105.050 105.048 105.049 105.087 105.088 105.073 105.074 105.075 105.089 128.015 113.014 128.019 128.020 128.021 128.022 128.023 104.039 104.007 104.028 104.050 129.004 129.001 105.030 105.031 105.068 103.296 103.297
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Surgical Kit Case PLUS Starter Drill PLUS Alvim Twister Drill 2.0 PLUS Twister Drill 2.0 PLUS Pilot Drill 2/3 PLUS Twister Drill 2.8 PLUS Twister Drill 3.0 PLUS Twister Drill 3.15 PLUS Twister Drill 3.3 PLUS Twister Drill 3.8 PLUS Twister Drill 4.3 PLUS Alvim Drill 3.5 PLUS Alvim Drill 4.3 PLUS Alvim Drill 5.0 PLUS Countersink Drill 3.5 PLUS SF Countersink Drill 4.1 PLUS Countersink Drill 4.3 PLUS SF Countersink Drill 4.5 and 5.0 PLUS CM Pilot Drill 2.8/3.5 PLUS CM Pilot Drill 3/3.75 PLUS CM Pilot Drill 3.3/4.0 PLUS CM Pilot Drill 3.6/4.3 PLUS CM Pilot Drill 4.3/5.0 Drill Extender Ti Contra-Angle Connection 4.1 and 4.3 Ti Ratchet Connection 4.1 and 4.3 Short Ti Ratchet Connection 4.1 and 4.3 Long Ti Contra-Angle Connection 5.0 Ti Ratchet Connection 5.0 Short Ti Ratchet Connection 5.0 Long Ti Short Ratchet Connection 3.5 Ti Long Ratchet Connection 3.5 CM Short Ratchet Connection CM Long Ratchet Connection CM Contra-Angle Connection Ti Contra-Angle Connection 3.5 CM Height Measuring Tool Implant Mount 3.3 Long Paralleling Guide 2.8/3.5 Paralleling Guide 3.0/3.75 Paralleling Guide 3.3/4.0 Paralleling Guide 3.6/4.3 Paralleling Guide 4.3/5.0 Short 0.9 Digital Driver Short 1.2 Digital Driver Digital Driver Contra-Angle Connection Torque Ratchet Millimeter Probe Titanium Tweezer II Plus Short Ratchet Connection II Plus Long Ratchet Connection II Plus Contra-Angle Connection II Plus Countersink Drill 4.3 II Plus Countersink Drill 5.0
Intermediate
SurgicalKit
Advanced
Kits
X X X X X X X X X X X X X X X X
X X X X X X X
X X X X X X X
X X X X X X X X
X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X
X X X X X X X X X
X X X X X X X X X X X
147
Note: Items that compose Neodent Kits are sold separately
148
Neodent Kits
Compact Surgical Kit Contents 110.254 103.170 103.162 103.213 103.163 103.164 103.172 103.173 103.239 103.211 103.216 103.217 103.219 103.091 105.047 105.045 105.046 105.073 105.074 105.075 128.019 128.020 128.022 104.039 104.007 104.050
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Compact Surgical Kit Case PLUS Starter Drill PLUS Twister Drill 2.0 PLUS Pilot Drill 2/3 PLUS Twister Drill 2.8 PLUS Twister Drill 3.0 PLUS Alvim Drill 3.5 PLUS Alvim Drill 4.3 PLUS SF Countersink Drill 4.1 PLUS Countersink Drill 4.3 PLUS CM Pilot Drill 2.8/3.5 PLUS CM Pilot Drill 3/3.75 PLUS CM Pilot Drill 3.6/4.3 Drill Extender Ti Contra-Angle Connection 4.1 and 4.3 Ti Ratchet Connection 4.1 and 4.3 Short Ti Ratchet Connection 4.1 and 4.3 Long CM Short Ratchet Connection CM Long Ratchet Connection CM Contra-Angle Connection Paralleling Guide 2.8/3.5 Paralleling Guide 3.0/3.75 Paralleling Guide 3.6/4.3 Short 0.9 Digital Driver Short 1.2 Digital Driver Torque Ratchet
149
Note: Items that compose Neodent Kits are sold separately. This technique requires specific accreditation. Information through +55 41 2169 1030
150
Neodent Kits
ZygomaticKit Contents 110.214 104.042 105.067 105.069 103.190 103.191 103.192 103.193 103.197 103.208 128.016 124.004 129.011 129.012 104.007 104.039
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Zygomatic Surgical Kit Case Zygomatic Installer Handpiece Zygomatic Contra-Angle Connection Zygomatic Drill Exchange Connection Zygomatic Plus Spheric Drill 2.9 Zygomatic Plus Twister Drill 2.7 Zygomatic Plus Pilot Twister Drill 2.7/3.3 Zygomatic Plus Twister Drill 3.3 Zygomatic CM Plus Countersink Drill Zygomatic Plus Pilot Twister Drill 3.3/3.7 Zygomatic CM Height Measuring Tool Zygomatic Lip Protector Zygomatic Bicortical Probe Zygomatic Probe Short 1.2mm Digital Driver Short 0.9 mm Digital Driver
151
Note: Items that compose Neodent Kits are sold separately
152
Neodent Kits
110.213 105.065 105.041 105.005 105.006 105.007 105.008 105.009 105.044 105.071 128.015 104.005 104.016 104.050
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Prosthetic Kit Case Torque Connection 0.9 Torque Connection 1.2 Short Torque Connection 1.2 Torque Connection 1.6 Torque Connection - Screwdriver Torque Connection Square Connection for Prosthetic Abutments Short Connection for Prosthetic Abutments Torque Connection 1.2 Long CM Height Measuring Tool Digital Driver for Torque Connections Transfer Driver Torque Ratchet
X X X X X X X X X X X X X X
Basic
Contents
Complete
ProstheticKit X X X X X
X X
X
153
PROSTHETIC SELECTION KIT FEATURES: :: Autoclavable polymer case :: Recommended for better planning of Morse Taper prosthetic abutments.
Note: Items that compose Neodent Kits are sold separately
154
Neodent Kits
CM Prosthetic Selection Kit Contents 110.223 114.191 114.192 114.193 114.194 114.195 114.196 114.197 114.198 114.199 114.200 114.201 114.202 114.203 114.204 114.205 114.206 114.207 114.208 114.209 114.210 114.211 114.212 114.213 114.214 114.215 114.216 114.217 114.218 114.219 114.220 114.221 114.222 114.223 114.224 114.230 114.231 114.232 114.233 104.007 114.226 114.227 114.228 114.335 114.336 114.337
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
CM Prosthetic Selection Kit Case CM Post 3.3x4x0.8 Prosthetic Selection CM Post 3.3x4x1.5 Prosthetic Selection CM Post 3.3x4x2.5 Prosthetic Selection CM Post 3.3x4x3.5 Prosthetic Selection CM Post 3.3x4x4.5 Prosthetic Selection CM Post 3.3x4x5.5 Prosthetic Selection CM Post 3.3x4x6.5 Prosthetic Selection CM Post 3.3x6x0.8 Prosthetic Selection CM Post 3.3x6x1.5 Prosthetic Selection CM Post 3.3x6x2.5 Prosthetic Selection CM Post 3.3x6x3.5 Prosthetic Selection CM Post 3.3x6x4.5 Prosthetic Selection CM Post 3.3x6x5.5 Prosthetic Selection CM Post 3.3x6x6.5 Prosthetic Selection CM Post 4.5x4x0.8 Prosthetic Selection CM Post 4.5x4x1.5 Prosthetic Selection CM Post 4.5x4x2.5 Prosthetic Selection CM Post 4.5x4x3.5 Prosthetic Selection CM Post 4.5x4x4.5 Prosthetic Selection CM Post 4.5x4x5.5 Prosthetic Selection CM Post 4.5x4x6.5 Prosthetic Selection CM Post 4.5x6x0.8 Prosthetic Selection CM Post 4.5x6x1.5 Prosthetic Selection CM Post 4.5x6x2.5 Prosthetic Selection CM Post 4.5x6x3.5 Prosthetic Selection CM Post 4.5x6x4.5 Prosthetic Selection CM Post 4.5x6x5.5 Prosthetic Selection CM Post 4.5x6x6.5 Prosthetic Selection CM Angled Post 3.3x6x1.5 17° Prosthetic Sel. CM Angled Post 3.3x6x2.5 17° Prosthetic Sel. CM Angled Post 3.3x6x3.5 17° Prosthetic Sel. CM Angled Post 3.3x6x1.5 30° Prosthetic Sel. CM Angled Post 3.3x6x2.5 30° Prosthetic Sel. CM Angled Post 3.3x6x3.5 30° Prosthetic Sel. WS Post 4.5x6x0.8 Prosthetic Selection WS Post 4.5x6x1.5 Prosthetic Selection WS Post 4.5x6x2.5 Prosthetic Selection WS Post 4.5x6x3.5 Prosthetic Selection Short 1.2 Digital Driver CM Anatomic Post Alt. 1.5 Prosthetic Sel. * CM Anatomic Post Alt. 2.5 Prosthetic Sel. * CM Anatomic Post Alt. 3.5 Prosthetic Sel. * CM Anatomic Lateral Post Alt. 1.5 Prosthetic Sel.* CM Anatomic Lateral Post Alt. 2.5 Prosthetic Sel.* CM Anatomic Lateral Post Alt. 3.5 Prosthetic Sel.* *Optional
155
156
Neodent Instruments
Neodent Instruments
157
Alvim Drill
Surgical steel
:: Available in surgical steel and Zircon; :: Instrument sequence for surgical alveolus in Alvim Implants.
Countersink Drill
Zircon
Ø 3.5
103.172
103.253
Ø 4.3
103.173
103.254
Ø 5.0
103.174
103.255
External Hex
:: Available in surgical steel and Zircon; :: Preparation of bone crest for Fitting the cervical bone Implants 3.3, 3.5, 3.75, 4.0, 4.5 and 5.0mm (external hex) and 4.3 and 5.0mm (internal hex).
(SF)
(SF)
Surgical steel
Zircon
Ø 3.3
103.209
103.265
Ø 3.5
103.366
Ø 4.1
103.239
103.292
Ø 4.3
103.211
103.267
Ø 4.5/ Ø 5.0
103.242
103.293
Internal Hex Surgical steel
Plus Starter Drill :: Available in surgical steel; :: Cortical rupture; :: 2.0mm diameter.
Ø 4.3
103.298
Ø 5.0
103.297
103.299
Ø 2.0
Pilot Drill :: Available in surgical steel and Zircon; :: Increasing the surgical alveolus diameter row, easing the penetration of the next drill; :: Replaces the Countersink when using Morse Taper Implants.
158
Zircon
103.296
103.170
Surgical steel
Zircon
2/3 mm
103.213
103.269
2.8/3.5 mm
103.216
103.272
3/3.75 mm
103.217
103.273
3.3/4 mm
103.218
103.274
3.6/4.3 mm
103.219
103.275
4.3/5 mm
103.220
103.276
3.8/4.3 mm
103.214
103.270
4.3/5.3 mm
103.215
103.271
5.3/6 mm
103.221
103.277
Neodent Instruments
Twister Drill
Surgical steel
:: Available in surgical steel and Zircon; :: Instrument sequence for surgical alveolus in Titamax Implants; :: Length: 35mm.
Zircon
Alvim Ø 2.0
103.171
Ø 2.0
103.162
Ø 2.8
103.163
103.244
Ø 3.0
103.164
103.245
Ø 3.15
103.165
103.246
Ø 3.3
103.166
103.247
Ø 3.8
103.167
103.248
Ø 4.3
103.168
103.249
Ø 5.3
103.169
103.250
Paralleling Guides 4.3/5.0
128.023
3.6/4.3
128.022
3.3/4.0
128.021
3.0/3.75
128.020
2.8/3.5
128.019
Ø 5.3/6.0
128.025
Ø 4.3/5.0
128.024
WS
:: Available in Titanium; :: Instrument to guide the implant’s position; :: Diameter of central band corresponds to CM Implant diameter CM Implants; :: Smaller side to be used after Ø2.0mm drill; :: Larger side to be used after the last drill before implant Instalation.
CM Ratchet Connection :: For Installing CM Implants with the Torque Ratchet (104.050); :: With six marks to indicate the hex index face position; :: The laser marks indicate the depth of implant Instalation, bone level, 1 and 2mm infra-bone and last marking (3mm) biological space.
Short
Long
105.073
105.074
159
CM Contra-Angle Connection :: To Install CM Implants with Contra-Angle, or attached to a Digital Driver for Contra-Angle Connections (104.028) for manual Instalation; :: With six marks to indicate the hex index face position; :: The laser marks indicate the depth of implant Instalation, bone level, 1 and 2mm infra-bone and last marking (3mm) biological space.
105.075
Contra-Angle Connection External Hex - Ti :: To capture the implant directly from the package; :: To Install External Hex Ti Implants with Contra-Angle, or attached to a Digital Driver (104.028) for manual Instalation; :: With clip to increase safety when transporting and positioning implants;
3.5
4.1/4.3
5.0
105.089
105.047
105.050
Contra-Angle Connection Internal Hex - II Plus
4.3/5.0
:: To capture the implant directly from the package; :: To Install Internal Hex II PLUS Implants with Contra-Angle, or attached to a Digital Driver (104.028) for manual Instalation; :: With clip to increase safety when transporting and positioning Implants.
105.068
Ratchet Connection External Hex - Ti :: To Install External Hex Ti Implants with a Torque Ratchet (104.050).
Ratchet Connection Internal Hex - II Plus :: To Install Internal Hex II PLUS Implants with a Torque Ratchet (104.050); :: With six marks to indicate the internal hexface position.
160
3.5
4.1/4.3
5.0
Short
105.087
105.045
105.048
Long
105.088
105.046
105.049
Short
Long
4.3/5.0
4.3/5.0
105.030
105.031
Neodent Instruments
CM Height Measuring Tool :: Available in Titanium; :: For selection of CM prosthetic abutments; :: Marks corresponding to transmucous heights.
5.5 3.5 1.5
128.015
6.5 4.5 2.5 0.8
Drill Extender :: Available in surgical steel; :: Screw for drill retaining; :: Screw attached to drill extender; :: To tighten or untighten the screw, use a half-turn on the 1.2 Digital Driver (104.007) is enough.
Titanium Tweezer :: To handle implants; :: New Tweezer system that prevents deviation in the active bit; :: Millimeter scale for checking during procedures; :: Self-locking implant.
103.091
129.001
Contra-Angle Hex Connection :: Available in surgical steel; :: Adaptation of hex assemblies; :: To insert implants using the motor and Contra-Angle; :: Silicone ring for better assembly tightening and transport.
Ratchet Hex Connection (Ratchet Driver Connection) :: Available in surgical steel; :: Adaptation of hex assemblies; :: Fit in square ratchets; :: Silicone ring for better tightening tightening and transport.
105.002
Short 105.001
Long 105.018
161
Tuff Driver :: Available in stainless steel; :: Manual implant Instalation.
104.047
Millimeter Probe :: Available in Titanium; :: To probe preparations and analyze depth; :: Millimeter scale for checking during procedures. 129.004
Digital Driver for Contra-Angle Connections
104.028
:: Available in surgical steel; :: Connected to Ti and II Plus Contra-Angle Connections, it becomes a manual driver for Implant Instalation.
Hex Digital Driver 0.9 mm :: Available in surgical steel; :: With diverging hex for better screw tightening and transport; :: Handling cover screws for Implants 3.3, 3.5, 3.75, 4.0, 4.3 and Cicatrizer 3.3 alt. 2 mm.
Hex Digital Driver 1.2 mm :: Available in surgical steel; :: With diverging hex for better screw tightening and transport.
162
Short 20 mm
Medium 25 mm
Long 38 mm
104.039
104.041
104.040
Short 20 mm
Medium 25 mm
Long 38 mm
104.007
104.012
104.010
Neodent Instruments
Torque Ratchet :: Available in surgical steel; :: Extremely safe (lower than 5% variation); :: Fitting for square connections; :: Collapsible ratchet that allows for proper assembly cleaning; :: Maintenance and calibration information through Customer Service +55 41 2169 1030.
104.050
Operation Instructions
The Neodent Torque Ratchet was designed to allow the necessary torque to be applied and simultaneous verification of that torque with the same Instrument.
All that is needed is to apply force to the RATCHET Handle 1 (never the ratchet body) until the value marked on the LATERAL SCALE 2 corresponds to the desired torque. The Neodent Torque Ratchet comes with pre-calibrated torques: 10, 20, 32, 45 and 60 N.cm. The ratchet function works in both directions, by simply pulling and turning the driver’s pin 180°. However, the torque measurements work only clockwise.
•WARNING: When inverting the torque direction,
the gear may come loose from the driver body and fall. Therefore, this inversion should only be done with the driver connected to a part or outside the patient’s mouth.
163
Prosthetic Adapting Driver 104.036
:: Used for tightening analogs and milling prosthetic Abutments.
Torque Meter Drivers and Connectors :: Available in surgical steel; :: Please note the connection that matches the screw in the prosthetic Abutment; :: To control the torque, the connections should be adapted to a Torque Ratchet (104.050); :: For manual torque, the connections should be adapted to a Digital Driver (104.005).
1.2 Short
1.6 Short
Prosthetic Abutment Short
0.9
1.2
1.6
Screwdriver
Square
Prosthetic Abutment
1.2 Long
Digital
105.041
105.042
105.044
105.065
105.005
105.006
105.007
105.008
105.009
105.071
104.005
Transfer Driver 104.016
:: Available in surgical steel; :: Recommended for Conical Transfer (used in closed tray techniques).
Trephine Drill :: Available in surgical steel; :: Collecting bone cylinder; :: Implant removal.
Ø3.3 mm
Ø 4.1 mm
Ø 4.3 mm
Ø 5.0 mm
Ø 8.0 mm
Ø10.0 mm
103.051
103.026
103.087
103.027
103.028
103.029
0.35mm
164
Neodent Instruments
Bone Profile Drill :: Available in surgical steel; :: Used in the second surgical stage; :: Conforms the bone around the implant platform, preparing an emergency profile compatible with the prosthetic Abutment’s profile; :: Each drill includes a guide with specific diameter.
External Hex Ø3.3 mm 103.039
Internal Hex
Ø 4.1 mm
Ø 4.3 mm
Ø 5.0 mm
Ø 4.3 mm
Ø 5.0 mm
103.030
103.085
103.031
103.102
103.103
7 and 9 mm Flag
128.026
:: Available in surgical steel; :: Recommended for prosthetic/surgical planning. :: 7 and 9 mm marks.
Alvim Radiographic Positioner
Ø 3.5 mm
:: Available in Titanium; :: Used to verify the depth of osteotomy without opening flaps; :: We suggest using a periapical x-ray to evaluate.
129.009
Ø 4.3 mm
Ø 5.0 mm
129.013
129.014
16 13
11.5
10
8
Angle Meter :: Available in Titanium; :: Angles: 17º and 30º; :: To select and plan the angle of prosthetic abutments during surgical procedures; :: Suggested use: After Twister Drill 2.0.
30º
17º
128.018 128.017
165
Compactors
17 mm 13 mm 9 mm
15 mm 11 mm 7 mm
:: Available in surgical steel; :: Concave active cutting bit for non-traumatic lifting the floor of the maxillary sinus; :: Used to prepare the surgical alveolus for Implant Instalation in the posterior maxillary region with low bone height; :: Marks from 7 to 17mm.
Expanders
17 mm 13 mm 9 mm
15 mm 11 mm 7 mm
:: Available in surgical steel; :: Convex active bit; :: Used when the bone width is insufficient, demanding bone compression and expansion before placing the implant; :: Marks from 7 to 17mm.
Osteotome Case :: Available in polymer; :: Autoclavable; :: Osteotomes sold separately.
1.8 mm
2.5 mm
3.0 mm
3.5 mm
4.0 mm
4.5 mm
110.154
110.155
110.156
110.157
110.158
110.159
1.8 mm
2.5 mm
3.0 mm
3.5 mm
110.160
110.161
110.162
110.163
110.180
Surgical Hammer
:: Available in surgical steel; :: Polymer active bit; :: Used in compactors and expanders; :: Weight: 130g.
166
126.001
Neodent Instruments
Curette for Sinus Lifting
126.008
126.009
126.010
126.011
126.012
1
3
4
5
7
:: Available in surgical steel; :: Used to displace the Sinusal Membrane.
Metallic Bone Scraper :: Used to remove autogenous bone applied in reconstructive surgery; :: Equipped with Titanium Nitride coated blade; :: Silicone handle; :: Autoclavable.
Disposable Bone Scraper :: Used to remove autogenous bone; :: Single use; :: Supplied sterile.
127.018
127.016
127.017
127.019
Negative
Straight
Positive
Blade
127.023
167
Disposable Bone Collector :: Available in polymer; :: To collect autogenous bone; :: Single use; :: Adaptable to vacuum pump; :: Includes two disposable sieves; :: Use second tip for saliva suction (watch for contamination).
107.003
107.008
Surgical Lip Retractor :: Available in surgical steel; :: Rounded edges to minimize surgical trauma.
Columbia Retractor
:: Available in surgical steel; :: Rounded edges to minimize surgical trauma.
Scalpel Handle :: Available in surgical steel; :: For standard scalpel blade use; :: Blade not included;
168
124.001
124.003
129.008
Neodent Instruments Blade and Bivers Handle :: Handle and blade in surgical steel; :: Non-traumatic extraction for implant Instalation; :: Similar to a periotome; :: Blades supplied individually.
129.002
129.005
Complementary Case :: Available in autoclavable polymer; :: Used to organize drills and ancillary connections. 110.233
Bone Particler :: Available in surgical Stainless steel; :: Increases in bone volume; :: Blade comes with 3-year warranty, oxidation free; :: Fitted with lever for easier use; :: Bone mill pesttle with slots to optmize bone block locking during use. :: Please avoid the use of bone originated from tissue banks.
127.011
Teste Bovine bone block with volume = 1.76 cm3
Magnified particles.
After particling, volume gain was about 7 times.
Note: Tech Support - +55 41 2169 1030
169
OSSTELL ISQ FEATURES: OSTELL ISQ is a portable equipment that applies Ressonance Frequency Analysis to measure the stability of dental implants and perform bone integration monitoring. The system includes the use of a SmartPeg, which is attached to the implant or abutment. The SmartPeg is excited by measuring probe magnetic impulses, which generate a ressonance frequency in response, used to calculate the implant stability value in the equipment. The higher this value, the higher the implant stability. The Osstell kit is composed of an equipment, probe, power supply, testing device, SmartPeg assembler, USB cable, AC plug, user manual (SmartPegs are sold separately).
132.041
170
Neodent Instruments
OsstellISQ Smartpegs 132.112 132.113 132.114 132.115 132.116 132.117 132.118 132.119 132.120 132.121 132.122 132.123 132.124 132.125 132.126 132.127 132.128 132.129 132.130 132.131 132.132 132.133 132.134
Smartpeg Type 01 Smartpeg Type 02 Smartpeg Type 03 Smartpeg Type 04 Smartpeg Type 05 Smartpeg Type 06 Smartpeg Type 07 Smartpeg Type 08 Smartpeg Type 09 Smartpeg Type 10 Smartpeg Type 11 Smartpeg Type 12 Smartpeg Type 13 Smartpeg Type 14 Smartpeg Type 15 Smartpeg Type 16 Smartpeg Type 17 Smartpeg Type 18 Smartpeg Type 21 Smartpeg Type 22 Smartpeg Type 23 Smartpeg Type 24 Smartpeg Type 25
132.135 132.136 132.137 132.138 132.139 132.140 132.141 132.142 132.143 132.144 132.145 132.146 132.147 132.148 132.149 132.150 132.151 132.152 132.153 132.154 132.155 132.156 132.157
Smartpeg Type 26 Smartpeg Type 27 Smartpeg Type 28 Smartpeg Type 30 Smartpeg Type 31 Smartpeg Type 32 Smartpeg Type 33 Smartpeg Type 34 Smartpeg Type 35 Smartpeg Type 36 Smartpeg Type 37 Smartpeg Type 38 Smartpeg Type 40 Smartpeg Type 44 Smartpeg Type 45 Smartpeg Type 46 Smartpeg Type 47 Smartpeg Type 48 Smartpeg Type 49 Smartpeg Type 50 Smartpeg Type 51 Smartpeg Type 52 Smartpeg Type A3 Note: Package with 5 units.
171
Neosurg XT Plus is small, light and can be easily carried. When you need to rely on high performance in oral and implant surgery, Neodent provides the Neosurg XT Plus motor, an internationally acknowledged tool. Silent, ergonomic, and practical, the Neosurg motor has programs and torque control to allow increased precision, safety and reliability during procedures. It offers secured control to your hands. Discover the Neosurg XT Plus motor.
172
Neodent Instruments
NeosurgMotor Control Unit CONTROL PANEL WITH SIMPLIFIED INTERFACE Advanced design with simple and intuitive panel. Membrane type keys, with no crevices to streamline cleaning. MECHANICAL CALIBRATION SYSTEM Besides electronic calibration, Neosurg XT Plus has a torque meter to ensure even greater micro motor precision and contra-angle. The calibration is performed directly by the professional, with no need of manufacturer maintenance. PERISTALTIC PUMP ATTACHED TO MOTOR No need to autoclave, only the hose system is sterilized.
INTELLIGENT COMMAND PEDAL
Micro Motor and Contra-Angle IRRIGATION SYSTEM WITH METAL CONNECTORS Allows perfect adaptation of the irrigation cable, offering resistance and safety. It can be sterilized.
All setups for the irrigation system, programs and speeds can be controlled through the pedal, leaving hands free for the surgical procedure. It was developed to avoid accidental system activation (progressive acceleration).
SHIELDED MICRO MOTOR WITH TITANIUM CASING Uses a magnetic induction system that produces neither noise nor vibration. High torque precision and speed variation. REDUCED SIZE OF CONTRA-ANGLE High resistance Titanium body. Internal and external irrigation system. Reduced head size and ergonomically compact body. Greater visibility, access and mobility inside mouth cavity.
173
174
Neodent reserves the right to perform technical changes without prior notice. Images for illustration purposes only.