Segmental Retaining Walls
Anchor Brighton Stone
®
IMPROVING YOUR LANDSCAPE ™
Anchor Brighton Stone
®
The Brighton Stone® is a fresh, clean look for residential wall applications. The patented rear lip facilitates construction, ensures proper alignment and a precise setback. Available in a variety of colors, the crisp defined look is the perfect complement to today’s residential landscapes. COMPOSITION AND MANUFACTURE Anchor Brighton Stone® is made from a “no slump” concrete mix. Made under extreme pressure and high frequency vibrations. APPLICATIONS
INSTALLATION
Retaining Walls • Tree Rings • Garden Terraces Planter Beds • Sand Boxes • Raised Planters
Depending on site conditions and or local building codes, engineering may be required. Step 1 – Site Preparation: Stake out project. Place a string line level on each
string line and adjust to where all lines are level. Measure down in wall increments using the height of the wall unit to determine placement of the top of the wall courses. For small landscape walls (3 courses or less) it is required the first course to be at least partially buried. For tall walls (4 to 8 courses) the first course should be fully buried at a minimum.
PRODUCT INFORMATION Anchor Brighton Stone® is available in one size. Anchor Brighton Stone® Nominal Dimensions 16 L x 10 W x 6" H Wt./Stone 52 lbs. Stones/Pallet 45 Approx. Wt./Pallet 2,340 lbs. Face ft./Pallet 30 Batter 10.6° Product Number 836
Step 2 – Excavation: All walls require excavation for a prepared base material
that extends a minimum of six (6) inches in front and back of the wall. For small walls, dig this trench a minimum half the height of the wall unit deep. For tall walls, dig your trench to a minimum depth of a full wall unit height. Compact floor of this trench with a compactor or hand tamper.
Step 3 – Base Preparation: For small wall base preparation, an option would
**While the Anchor Wall Cap can provide a decorative finishing touch for Brighton Stone®, it is not available in all markets.
Anchor Wall Cap #824 Nominal Dimensions 17 1/4 L x 10 W x 3" H Wt./Stone 34 lbs. Stones/Pallet 90 Approx. Wt./Pallet 3,060 lbs. Linear ft./Pallet 101 Product Number 824
Step 4 – Leveling: For both small and tall walls a maximum of one-half inch of
coarse sand is allowable to level the top profile of the base material. When placing wall units, level the surface of all wall units in both directions with a carpenter’s level. Replace the string-line where the top of your wall course will be and check for horizontal level prior to each course installation.
Step 5 – Laying Stones: Always begin at the lowest point of the wall. Level each
unit in both directions with a minimum two (2) foot carpenter’s level. Once the base course is complete, continue assembling additional courses by positioning the units in a running bond pattern relative to the course beneath, taking care not to align joints vertically. Securely engage the unit to the lower units. Backfill and compact material behind the wall in a four (4) inch to a maximum six (6) inch layer. Install a granular no fines material as a drainage zone a minimum of four (4) to six (6) inches thickness directly behind the wall. Compact materials with a compactor or hand tamper. A four (4) inch perforated plastic pipe may be required behind wall.
** Caps not available in all markets. * Fractional dimensions are nominal.
Typical Cross Section of Anchor Brighton Stone® Installation
Step 6 – Cutting Stones: When building your wall, you may need partial stones
to finish coursing. Place the to-be-cut unit at its finished position in the wall. Mark the cut line. To split a stone, use safety glasses, a hammer and a chisel. Place the unit on a hard surface. Position the chisel at the cut mark and proceed to hammer the chisel scoring the cut line. Score the unit on all sides. Once the perimeter score is complete, strike the chisel on the score line until it breaks.
Drainage Aggregate
Complete installation and specification details are available by contacting your Pavestone Company Sales Representative.
w w w. p a v e s t o n e . c o m © 2007 by Pavestone Company All Rights Reserved. and Improving Your Landscape™ are trademarks of the Pavestone Company. “Anchor Wall Systems”, the “A” logo and “Brighton Stone” are registered trademarks of, and are manufactured under license from, Anchor Wall Systems, Inc. These Anchor products are protected by U.S. and International patents and pending patent applications.
Finished Grade
Drain Tile
Note: Colors are shown as accurately as possible in brochures and samples, but due to the nature of the product, regional color differences and variables in print reproduction, colors may not match exactly.
• • • • • • • • • •
Anchor Brighton Stone®
Native Soil
Prepared Base
Atlanta, GA: Austin/San Antonio, TX: Boston, MA: Charlotte, NC: Cartersville, GA Cincinnati, OH: Colorado Springs, CO: Dallas/Ft. Worth, TX: Denver, CO: Hagerstown, MD:
Member of ASLA and NCMA
(770) (512) (508) (704) (770) (513) (719) (817) (303) (240)
306-9691 558-7283 947-6001 588-4747 607-3345 474-3783 322-0101 481-5802 287-3700 420-3780
ICPI Charter Member
• • • • • •
Houston, TX: Kansas City, MO: Las Vegas, NV: New Orleans, LA: Phoenix, AZ: Sacramento/ Winters, CA: • St. Louis/ Cape Girardeau, MO:
(281) (816) (702) (985) (602)
391-7283 524-9900 221-2700 882-9111 257-4588
(530) 795-4400 (573) 332-8312
Retaining Wall Systems
SKU# CM 156v7 07/07
be to place a mixture of dry sand and Portland cement (one shovel of Portland to four shovels of sand). Place the sand-cement mixture a minimum of four (4) inches at the bottom of the trench. For tall walls, you’ll need a more substantial base. Granular road base is preferable at a minimum four (4) inch placement. Compact the material with a compactor or hand tamper.