Section B - Hydraulic Hose by PIRTEK

WARNING SAFETY PRECAUTIONS FOR THE USE OF PIRTEK® HOSE ASSEMBLIES Your Personal Safety may directly or indirectly be compromised if the hose assembly is abused. By following the INSTRUCTIONS below, the more common abuses of hose and hose assemblies can be avoided. INSPECT the hose assembly before each use. REPLACE the hose assembly immediately if: A. The cover appears abnormal B. You believe it may be abnormal C. There is any fluid leakage D. The fittings are damaged E. The hose is damaged F. Reinforcement is visible through the cover DO NOT EXCEED the maximum working pressure of the hose. DO NOT KINK the hose assembly. DO NOT BEND beyond the specified minimum bend radius of the hose. DO NOT EXPOSE to temperatures beyond the published maximums for the hose or fluid being conveyed. DO NOT USE AS A STRENGTH MEMBER for pulling or lifting equipment. Use support cables for vertical installations. USE ONLY WITH COMPATIBLE FLUIDS as outlined in the Chemical Compatibility Charts or as specifically approved in writing by Pirtek Fluid Systems. PIN PRICK THE COVER of hoses used for compressed air above 17 bar or 250 psi to allow the safe escape of air that permeates through the liner and reinforcement (except STH, R5HT and 3130). The maximum working pressure and temperature must also be reduced by 30%. Use only Pirtek HOSE AND FITTINGS COMBINATIONS as designated in their current assembly guidelines. Use only Pirtek PROCEDURES and ASSEMBLY EQUIPMENT as published and maintained in their M.A.P.S. documentation. Relationship between actual working presasure and service life

100 Experimental pressure waveform

90 Pressure as a % of Rated Pressure at 100

Peak pressure 150 ± 7% Pressure rising rate

80 70 % of Service Life

• The use of conventional wire reinforced rubber hose often entails the pressure fluctuations of fluid. • The factors concerned with such pressure fluctuations are generally classified into two: those stemming from the pump itself, and the others ascribable to external impacts imparted to the hose via the operating demands. The latter are considered to have the greater effect on the service life of the hose. • External impulse pressure is estimated to be 150% of the set pressure (actual working pressure) of a relief valve, and sometimes exceeds 300%.

125

Rated pressure

100 75 50

25 (kgf/cm ) 0

5% of one cycle

150

15% of one cycle 1/35 minute a cycle

30 20 10 0

100 125 150

200 300 400 Actual working pressure Recommended working pressure

500

600

This page is part of a complete catalogue containing technical and safety data. All data must be reviewed when selecting a product. Pirtek reserve the right to change technical specifications without notice Rev B

RUBBER HOSES SELECTION GUIDE Page Group

Product Code

Construction

Normal Usage

Features & Bene Benefits

(See main Specifications page for details and Approvals)

6-7 8 9 10 11 12 13 14-16 17-18 20 21 22

HYDRAULIC

R4HT / IROFSD Oil Fuel Suction

Hydraulic suction & delivery hose for fuels & mineral oils with aromatic content ≤ 40%

Synthetic smooth oil resistant inner tube. 2 braids of textile & a metal spiral. MSHA

IRFWSDH FRAS Suction/Delivery MPH Multipurpose IRFAW FRAS Air / Water LPHT Textile braid Hi-Temp R5HT Hi-Temp. Truck Hose HTAB/HTFH Engine & Air Brake JW210A / JW250 / JW400 Jet Wash Hose R1AT / R1ATFS One wire braid R2AT/2SC Two wire braid R2ATHT High Temp. 2 wire hose JH70 Jacking Hose

Hardwall FRAS hose for arduous air / water applications in u/ground coal mining

Electrically conductive NBR liner and CR cover meeting AS2660 requirements

High quality black multi-purpose hose with spiral wound textile reinforcement

Synthetic black rubber inner and outer. Abrasion and weather resistant. Oil resistant

Softwall hose for arduous air/water applications in underground mining

Weather resistant black cover with orange spiral. Fire resistant / anti static rating

Low pressure hydraulic fluids, aqueous emulsions, air transfer and water

Low pressure high temp. hose with oil resistant liner suited to push fit fittings

Medium pressure air and hydraulic hose common on American equipment

Internal diameters match the inside diameter of copper tube to yield an unrestricted flow

Specifically intended for trucking industry applications involving diesel fuel / air brakes

Black rubber with poyester textile outer cover for safe escape of entrapped air

Flexible high pressure compact hose for pressure cleaning with water and detergents

210 and 250 bar versions with 1-wire braid, 400 bar version with 2-wire braid

Medium pressure hose for hydraulic fluids and aqueous emulsions and water

Normally black but R1ATFS has red cover to indicate use in fire suppression systems

High pressure hose for hydraulic fluids and aqueous emulsions and water

Synthetic rubber oil resistant liner and abrasion resistant cover. 2 steel braids

High pressure hose for hydraulic fluids and aqueous emulsions and water

As above but high temperature rubber formulation. Blue cover

High pressure hydraulic hose for jacking applications

Synthetic rubber oil resistant liner and abrasion resistant cover. 2 steel braids

C21 Isobaric 210 bar C25, PC25 Isobaric 250 bar

PC28PS Isobaric 280 bar

25, 28

C35, PC35 Isobaric 350 bar

26, 29

C42, PC42 Isobaric 420 bar

C45 Isobaric 450 bar

JBF Large Bore Hose

Large bore medium pressure hose for hydraulic fluids incl. aqueous emulsions

Spiral construction. Prolonged usage with water based fluids will corrode reinforcement

LPG LP Gas Hose

High pressure hose for transfer of LPG,

Woven black poly cover with blue trace over single st. steel braid / teflon liner. AGA approved.

R12C 4000-2500 psi Spiral

R13C 5000psi Spiral

High pressure multi-spiral hose for hydraulic fluids such as glycol, mineral oils, fuels, hydrocarbons etc. Provide flexibility and high temperature resistance

WB1000 Water Blast Hose

MISC.

23, 27

WB1100 Water Blast Hose

Class 21 hoses suit 210 bar WP Isobaric (constant working pressure for all sizes) range of hoses exclusive to Pirtek. Simplifies hose selection in circuits of known working pressure ‘PS’ Suffix denotes extreme abrasion resistant sheath over the cover ‘PC’ Prefix denotes Komatsu® genuine hoses

Class 25 hoses suit 250 bar WP Class 28 hoses suit 275 bar WP Class 35 hoses suit 350 bar WP Class 42 hoses suit 420 bar WP Class 45 hoses suit 450 bar WP

butane-propane on stationary and mobile eqpm’t.

Very high constant pressure hose for water scaling systems. Suitable for passage of water and aqueous solutions

Compatible with Caterpillar® reusable fittings

2.5 : 1 safety factor. Do not use in hydraulic systems

THERMOPLASTIC HOSES SELECTION GUIDE Page Group

Product Code

Construction

Normal Usagee

Features & Bene Benefits

(See main Specifications page for details and Approvals)

30CT Cold temp. hose

Flexible in cold temperatures (coldrooms). Small OD and good over sheaves

Constant 207 bar working pressure for all sizes. Perforated cover for gaseous applications

3JET Water jetting hose

Medium pressure hose for water jetting and drain cleaning. Low elongation

Constant 207 bar working pressure for all sizes. Perforated cover for gaseous applications

30CTX2 / 30CTX3 Multi-Line hose

Commonly found in forklift applications in cold rooms

Constant 207 bar working pressure for all sizes. Hytrel core tube and perforated cover. 2 or 3 line

3130 General purpose R7

General hydraulics, material handling, pneumatics, and agricultural equipment

The original SAE 100R7 design with nylon tube and urethane cover. Economical

3360X2 Twin forklift hose

Similar to 30CT except with nylon core tube

As for 30CT but with nylon tube and a wider range of sizes

37AL R7 non-conductive

Non conductive hydraulic hose for aerial lift equipment

Polyester core and good cold weather flexibility. SAE 100R7 performance

37ALX2 Twinline non-conductive

Non conductive twin line hydraulic hose for aerial lift equipment

Polyester core and good cold weather flexibility. SAE 100R7 performance

3800 Compact R8

Pilot lines, general hydraulics, and machine tools at higher pressures than 100R7

Compact dimensions due to aramid fibre reinforcement - suits 100R7 fittings

3E80 Non-conductive R8

Non conductive hydraulic hose for aerial lift equipment with higher working pressures

Dimensionally as for 3R80 hose. Nylon core and orange urethane cover

3R80 General purpose R8

General hydraulics, material handling, forestry and construction

The original 100R8 with nylon core and urethane cover. Long impulse / flex life

3VE0 High Pressure Jacking

Extreme pressure hose for high pressure jacks and rescue equipment

Orange cover signifies electrically non conductive hose

STH St. Steel TeflonÂŽ hose

Laundry equipment, plastic moulding presses, steam and hot air discharge

Teflon liner and SS braid allow high temperature and chemical capability

42 43 44

THERMOPLASTIC

ORDERING PIRTEK ASSEMBLIES Should you wish to describe a Pirtek hose assembly in an abbreviated form, please use the following format. A forward slash is used to separate each field. Product Codes for fittings can be found in Pirtek Catalogue Section C (except Mining Fittings Section U)

If spiral guard SSG-025 were fitted over the full length, the designation would be: R1AT-12 / JF1-1712J / C614-1212J / 1200 / SSG-025 If both ends were fitted with the 45Â° flanged elbow set in alignment, the designation would appear: R1AT-12 / C614-1212J / 1200 / 0 Generic Pattern : Hose / End A / End B / Length / Protection / Angle

FAST FIND TABLE SIZE, PRESSURE, TEMPERATURE

Product Code & Hose Type dia. (ins.) mm size

Working Pressure (bar)

Temp.

⅛

³/16

5/16

⅜

5/8

1¼

1½

1¾

2½

3½

-003

-004

-006

-008

-010

-013

-016

-019

-025

-032

-038

-045

-050

-063

-076

-090

-100

-125

R4HT

Hydraulic Suction/Delivery

IROFSD

Oil Fuel Suction

IRFWSDH

FRAS Air/Water Suction

MPH

Multipurpose

IRFAW

FRAS Air / Water

LPHT

Low pressure hydraulic

R5HT

High Temp 100R5

20 35

Pg.

°C -40°/+135°

-20°/+100°

-15°/+70°

-40°/+100°

-15°/+70°

-40°/+149°

Unique diameters throughout range 3/16” to 1.13/16”

-40°/+135°

HTAB/HTFH Engine/Air Brake Hose

Unique diameters throughout range 3/16” to 1.3/8”

-40°/+149°

JW210A

Jet Wash 210 bar

210

-40°/+155°

JW250 / A

Jet Wash 250 bar

250

-40°/+155°

JW400 / A

Jet Wash 400 bar

400

-40°/+155°

R1AT

1-Wire Hydraulic

-40°/+100°

R1ATFS

Fire Suppression

-40°/+100°

R2AT/2SC

2-Wire Hydraulic

-40°/+100°

R2ATHT

2-Wire High Temp.

-40°/+150°

JH70

Jacking Hose

-40°/+100°

C21

Isobaric 210 bar

C25, PC25

Isobaric 250 bar

PC28PS

Isobaric 280 bar

C35, PC35

Isobaric 350 bar

C42, PC42

Isobaric 420 bar

C45

Isobaric 450 bar

JBF

Large Bore

LPG

LPG Gas Hose

R12C

4000-2500 psi Spiral

R13C WB1000 WB1100

1100 bar Water Blast

250

225

215

160

180

160

330

275

250

215

165

125

80 69/70 70

396

345

293

224

207

172

155

120

103

700

400

350

140

180

225 415

105

210 250 280 380 420

350

420

350

250

-40°/+120°

23,27

-40°/+120°

250

280

350

-40°/+120°

25,28

420

-40°/+120°

25,29

-40°/+100°

-20°/+125°

450 140 26

-40°/+120°

26 276

276

207

172

-40°/+121°

5000 psi Spiral

345

-40°/+120°

1000 bar Water Blast

1000

-40°/+80°

-54°/+94°

-40°/+66°

-54°/+94°

-40°/+100°

-54°/+94°

30CT

Cold Temp Isobaric 207

3JET

Water Jetting Hose

30CTX2

Twin Line 30CT

3130

Medium Pressure

3360X2

Twin Line Forklift

37AL

Non-conductive

37ALX2

Twin Line 37AL

3800

High Pressure compact

3E80

HP Non-conductive

3R80

High Pressure

3VEO

High Pressure Jacking

STH

St Steel Teflon Hose

276

1100 207 331 172

207

331 207

207

172

155

138

207 86

207 207 345 345 206

207

-54°/+100°

207

-54°/+100°

345

276

241

-40°/+100°

345

276

241

-40°/+100°

345

276

241

-40°/+100°

689

551

-40°/+66°

-55°/+240°

206

172

138

120

155 103

138 69

Chemical Compatibility Tables Commence page 50

R4HT HIGH TEMP OIL SUCTION & DELIVERY

Construction

Applications

Reference Specifications

Inner Tube:

Hardwall hose for suction and delivery of oil

Tested in accordance with performance

Black smooth NBR (Nitrile) compound, oil

at high temperatures in hydraulic systems.

specifications:

resistant

Extremely flexible.

SAE100 R4

Reinforcement:

Temperature Range:

Approvals:

High strength synthetic cord plus embedded

-40°C up to +135°C mineral oil

MSHA

steel helix wire

-40°C up to +70°C water based fluids

Prolonged usage with water based fluids at temperatures above 70°C will allow wire corrosion as a result of diffusion through the inner liner.

Cover:

Comment:

Hose Tails:

Black, smooth (wrapped finish) Hypalon rubber

Lay line example may not be a true indication

Pirtek ‘J’ Series for some sizes

compound flame retardant, resistant to abrasion,

of current status. Refer Pirtek for current

L Series, Cam & Groove, Combination Steel

oils and weathering

information

(all with clamps)

Lay line example: Embossed text on black background. Note Comment above

PIRTEK R4 HIGH TEMP R4HT-32 50.8mm (2”) 10 BAR (145 PSI) MSHA

Nominal ID

Product Code

OD ins 3/4

mm 30.5

Pressure bar working 21

min burst 83

vacuum 0.9

Min bend radius mm 60

Weight

R4HT-12

mm 19.1

R4HT-16

25.4

0.9

0.84

R4HT-20

31.8

1.1/4

0.9

100

1.02

R4HT-24

38.1

1.1/2

0.9

125

1.33

R4HT-32

50.8

0.9

150

1.71

R4HT-40

63.5

2.1/2

0.9

200

2.71

R4HT-48

0.9

240

3.28

R4HT-56

3.1/2

108

0.9

280

4.29

R4HT-64

102

121

0.9

320

4.80

Kg/m 0.66

IROFSD OIL / FUEL SUCTION & DELIVERY

Construction

Applications

Inner Tube:

Light weight hardwall suction and delivery hose

Black smooth NBR (Nitrile) compound, oil

for fuels having an aromatic content up to 30%,

resistant

and mineral oils. Suitable in hydraulic systems and for loading and unloading of tank trucks, refineries and maintenance shops

Reinforcement:

Temperature Range:

Limitations:

High strength synthetic cord plus embedded

-20째C up to +100째C

Not suitable for ester oils

Cover:

Comment:

Hose Tails:

Black, smooth (wrapped finish) SBR weather

Lay line example may not be a true indication

Pirtek J,T, 932, 934, 954 Series crimp fittings

resistant rubber compound

of current status. Refer Pirtek for current

L Series, Cam & Groove, Combination Steel

information

(all with clamps)

steel helix wire and anti-static copper wire

Lay line example: Black text on yellow background. Note Comment above

PIRTEK OIL FUEL S/D IROFSD 10 BAR (150psi) WORK.PRESS.

Nominal ID

Product Code

OD ins 3/4

mm 30

Pressure bar working 10

min burst 30

vacuum 0.9

Min bend radius mm 80

Weight

IROFSD-019

mm 19

Kg/m 0.67

IROFSD-025

0.9

105

0.80

IROFSD-032

1.1/4

0.9

135

0.98

IROFSD-038

1.1/2

49.5

0.9

165

1.34

IROFSD-045

1.3/4

0.9

180

1.60

IROFSD-051

0.9

230

1.84

IROFSD-063

2.1/2

0.9

300

2.79

IROFSD-076

0.9

360

2.94

IROFSD-102

102

118

0.9

500

4.94

IROFSD-125

125

145

0.9

620

7.50

IRFWSDH FRAS AIR / WATER SUCTION & DELIVERY

Construction

Applications

Reference Speifications

Inner Tube:

Hardwall hose designed for arduous air / water

Approvals:

Black, smooth, electrically conductive NBR

applications in underground coal mining, where

Meets or exceeds

(Nitrile) rubber compound

fire resistant, anti static properties are required

AS2660, incorporating AS1180.13A and

Reinforcement:

Temperature Range:

High strength synthetic cord plus helix wire

-15°C up to +70°C

Cover:

Comment:

Hose Tails:

Black smooth (wrapped finish) electrically

Lay line example may not be a true indication

Industrial fittings

conductive CR (Neoprene) synthetic rubber

of current status. Refer Pirtek for current

High pressure 2 or 4 bolt clamps

compound, fire, oil weathering and UV resistant

information

Pirtek “J” series 2

AS1180.10B FRAS FRAS Rated in all sizes

Lay line example: White text on orange background. Note Comment above

PIRTEK FRAS WATER SUCTION & DELIVERY IRFWSDH 20BAR (290PSI) W.P MEETS & EXCEEDS AS2660 CLASS B

IRFWSDH-025†

DN 25

mm 25.4

ins 1

mm 42.5

working 20

min burst 80

vacuum 0.9

Min bend radius mm 125

IRFWSDH-051

50.8

0.9

255

2.58

IRFWSDH-063†

63.5

2.1/2

0.9

320

3.27

Nominal ID

Product Code

Pressure bar

Weight kg/m 1.34

IRFWSDH-076

0.9

375

3.96

IRFWSDH-102

100

102

124

0.9

610

5.71

IRFWSDH-152†

150

152

178

0.9

1000

11.46

† Subject to availability

MPH MULTIPURPOSE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Low pressure hose for fluids such as mineral

Exceeds SAE J 517 (100 R6)

Black, smooth NBR (Nitrile) seamless synthetic

and vegetable oils, aqueous emulsions, water,

Exceeds EN 854 R6

rubber, oil resistant

air and inert gases.

JIS B 8360

Reinforcement:

Temperature Range:

Impulse Testing:

Two or four spirals of textile fibre

Water 0º C to +50º C (continuous)

400 000 cycles of JIS waveform @ 133%

Water 0º C to +70º C (temporary)

of working pressure (hose only) all sizes

Air -40º C to +50º C (in case of air applications,

Safety Factor 4:1

pressure should be less than 15bar) Other fluid -40°C up to +100°C -40°C up to 70°C external ambient Cover:

Comment:

Hose Tails:

Black CR (Neoprene) synthetic rubber compound Lay line example may not be a true indication

Pirtek ‘P’ Series all sizes

resistant to abrasion, oils, ozone and weathering

Pirtek ‘T’ Series option on 3/8, 1/2, 5/8 sizes

of current status. Refer Pirtek for current information

Lay line example: Green text on black background. Note Comment above

PIRTEK MULTI MPH-12 (3/4”) 35BAR W.P. (500 PSI)

Product Code

Nominal ID

Reinforcement

Pressure bar

Min bend radius

Weight

mm 55 60 65 90

Kg/m 0.15 0.19 0.21 0.28

MPH-04 MPH-05 MPH-06 MPH-08

mm 6.3 8.0 9.5 12.7

in 1/4 5/16 3/8 1/2

4 fabric spiral 4 fabric spiral 4 fabric spiral 4 fabric spiral

mm 14.0 15.8 17.4 21.3

working 35 35 35 35

min burst 140 140 140 140

MPH-10

15.9

5/8

2 fabric spiral

23.5

140

110

0.30

MPH-12 MPH-16

19.0 25.4

3/4 1

4 fabric spiral 4 fabric spiral

31.4 37.5

35 35

140 140

135 170

0.59 0.74

IRFAW FRAS AIR / WATER / STONEDUST

Construction

Applications

Inner Tube:

Softwall hose designed for arduous air / water

Black smooth electrically conductive NBR

applications in underground coal mining, where

(Nitrile) oil resistant rubber compound

fire resistant anti static properties are required

Reinforcement:

Temperature Range:

Approvals:

2 or 4 spiral plies of high strength synthetic cord

-15°C up to +70°C

Meets or exceeds AS2660-91B, incorporating AS1180.13A and AS1180.10B

Cover:

Comment:

Hose Tails:

Black smooth (wrapped finish) electrically

Lay line example may not be a true indication

Industrial fittings / FFI Ferrules

conductive CR (Neoprene) rubber compound

of current status. Refer Pirtek for current

High pressure 2 or 4 bolt clamps

with orange spiral stripe. Fire, oil and weather

information

resistant

Lay line example: Black text on orange background. Note Comment above PIRTEK AIR / WATER / STONEDUST FRAS IRFAW 20 BAR (290 psi) WORK. PRESS. MEETS & EXCEEDS AS 2660 “CLASS B”

Product Code IRFAW-013 IRFAW-019 IRFAW-025 IRFAW-032 IRFAW-038 IRFAW-051 IRFAW-063 IRFAW-076 IRFAW-102

Nominal ID

Reinforcement

13 19 25 32 38 51 63.5 76 102

1/2 3/4 1 1.1/4 1.1/2 2 2.1/2 3 4

2 spiral plies 2 spiral plies 2 spiral plies 2 spiral plies 2 spiral plies 2 spiral plies 4 spiral plies 4 spiral plies 4 spiral plies

Pressure bar

Weight

working

min burst

Kg/m

23 29 37 46 52.5 66 81 93 120

20 20 20 20 20 20 20 20 20

80 80 80 80 80 80 80 80 70

0.36 0.47 0.70 1.02 1.21 1.60 2.27 2.53 3.60

LPHT LOW PRESSURE HIGH TEMP. HOSE

Construction

Applications

Inner Tube:

Low pressure textile braid hose for petroleum

Reference Specifications

Seamless CPE/AQP rubber, oil resistant

based hydraulic oil, lubricating fluids, diesel, unleaded petrol, aqueous emulsions, water and air. Not recommended for impulse applications. Note: Not recommended for Ethanol/Methanol, including blends.(Excluding E10)

Reinforcement:

Temperature Range:

Approvals

One braid of polyester

-40Â°C up to +149Â°C hydraulic, transmission oils

MSHA 2G

(petroleum based) & Diesel -40Â°C up to +100Â°C E10 & B20 (biodiesel) Cover:

0Â°C up to +82Â°C water, water based fluid &

Blue CPE rubber, resistant to oils, ozone, flame

glycol (anti-freeze)

and weathering

0Â°C up to +121Â°C air -40Â°C up to +121Â°C ambient Comment:

Hose Tails:

Lay line example may not be a true indication

Pirtek â&#x20AC;&#x2DC;Pâ&#x20AC;&#x2122; Series

of current status. Refer Pirtek for current

Pirtek â&#x20AC;&#x2DC;Tâ&#x20AC;&#x2122; Series

information

Lay line example: Black text on blue background. Note Comment above

Product Code

LOW PRESSURE HIGH TEMP LPHT-04 6.4mm (1/4â&#x20AC;?) 21 bar (304 PSI) W.P MSHA

Nominal ID

Pressure bar

Min bend radius

Weight

LPHT-04 LPHT-06

mm 6.4 9.5

in 1/4 3/8

mm 12.4 16.0

working 21 21

min burst 84 84

Vacuum 0.9 0.9

mm 76.2 76.2

Kg/m 0.12 0.18

LPHT-08

12.7

1/2

19.0

0.9

127.0

0.22

LPHT-10 LPHT-12

15.9 19.1

5/8 3/4

23.1 26.4

21 21

84 84

0.6 0.6

152.4 177.8

0.31 0.37

R5HT LOW PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Low to medium pressures hose that will handle

Exceeds SAE J 517 (100 R5)

Seamless CPE/AQP rubber, oil resistant

high temperature hydraulic fluids such as mineral and vegetable oils, diesel, B20, petrol, E10, aqueous emulsions, water, air and inert gases

Reinforcement:

Temperature Range:

One textile braid and one braid of high tensile

-40°C up to +149°C hydraulic, transmission oils

steel wire

(petroleum based) & Diesel

Impulse Testing: See Table below for Impulse Test criteria (hose only)

-40°C up to +100°C E10 & B20 (biodiesel) 0°C up to +82°C water, water based fluid & glycol (anti-freeze) 0°C up to +121°C air -40°C up to +121°C ambient Cover:

Comment:

Hose Tails:

Black synthetic rubber with blue polyester textile

Lay line example may not be a true indication

Pirtek ‘A’ Series (field attachable)

outer braid resistant to abrasion, oils, ozone and

of current status. Refer Pirtek for current

Pirtek ‘R’ Series (crimp)

weathering. Permeable cover allows safe escape information of entrapped air when used to conduct high pressure air

Lay line example: White ink-jet text on blue background. Note Comment above PIRTEK HI-TEMP 8.3MM (5/16”) R5HT-06 155 BAR (2,250PSI) WORK. PRESS: 150°C./SAE J1402 TYPE AII 2Q04 BATCH 0037

Product Code

Nominal ID

Pressure bar

Min bend radius

Weight

R5HT-04 R5HT-05 R5HT-06 R5HT-08 R5HT-10

mm 5.1 6.8 8.3 10.7 13.2

in 3/16 1/4 5/16 13/32 1/2

mm 13.2 14.8 17.1 19.5 23.4

working 207 207 155 138 121

min burst 827 827 620 552 483

mm 76 86 102 117 140

Kg/m 0.19 0.24 0.34 0.39 0.55

150 000 150 000 150 000 150 000 150 000

R5HT-12

16.4

5/8

27.4

103

414

165

0.69

150 000

R5HT-16 R5HT-20 R5HT-24 R5HT-32 †

22.8 29.2 35.5 46.6

7/8 1.1/8 1.3/8 1.13/16

31.4 38.1 44.4 56.2

55 43 34 20.7

221 172 138 83

187 229 267 337

0.66 0.78 1.00 1.40

150 000 100 000 100 000 100 000

† Does not comply with SAE 100R5 operating pressure of 24 bar or minimum burst pressure of 96 bar

Test Impulses

HTAB / HTFH ENGINE & AIR BRAKE* HOSE EXTRA FLEXIBLE LOW PRESSURE HOSE Construction

Applications

Reference Specifications

Inner Tube:

Low to medium pressures hose that will handle

* SAE J1402 Type AII in sizes -04 through -12

Seamless CPE/AQP rubber, oil resistant

high temperature hydraulic fluids such as mineral FMVSS106 and vegetable oils, aqueous emulsions, diesel,

Consult Pirtek for specific Industry Approvals

B20, petrol, E10 fuels, lubricating oils, coolants, water, air and inert gases Reinforcement:

Temperature Range:

One polyester braid and one braid of high tensile

-40°C up to +149°C hydraulic, transmission oils

steel wire

(petroleum based) & Diesel -40°C up to +100°C E10 & B20 (biodiesel) 0°C up to +82°C water, water based fluid & glycol (anti-freeze) 0°C up to +121°C air -40°C up to +121°C ambient

Cover:

Comment:

Hose Tails:

Black synthetic rubber with black polyester textile Lay line example may not be a true indication

Pirtek ‘A’ Series (Field Attachable)

outer braid resistant to abrasion, oils, ozone and

Pirtek ‘R’ Series (Crimp)

of current status. Refer Pirtek for current

weathering. Permeable cover allows safe escape information of entrapped air when used to conduct high pressure air

Lay line example: White Ink-Jet on black background. Note Comment above PIRTEK HI-TEMP AIR BRAKE 7.9MM (5/16”) HTAB-06 103 BAR (1500PSI) WORK. PRESS: 149°C. SAE J1402 TYPE AII 2Q07 PIRTEK HI-TEMP FLEX HOSE 22.4MM (7/8”) HTFH-16 28 BAR (400PSI) WORK. PRESS: 149°C. 2Q07

Product Code

Nominal ID

Pressure bar

Min bend radius

Weight

working

min burst

Kg/m

HTAB-04 HTAB-05 HTAB-06 HTAB-08 HTAB-10

4.8 6.4 7.9 10.4 12.7

3/16 1/4 5/16 13/32 1/2

13.7 15.7 17.7 20.1 24.0

138 103 103 86 86

552 412 412 345 345

19.1 25.4 31.8 44.5 57.2

0.19 0.24 0.28 0.33 0.50

HTAB-12

15.9

5/8

27.9

207

69.9

0.58

HTFH-16 HTFH-20 HTFH-24

22.4 28.7 35.1

7/8 1.1/8 1.3/8

32.3 38.9 46.0

28 21 17

110 83 69

88.9 114.3 139.7

0.55 0.68 0.85

JW210A JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

One braid of high tensile steel wire

-40°C up to +155°C

Cover:

† Comments:

Hose Tails:

Pin pricked black synthetic rubber resistant to

Not suitable for steam and hydraulic applications.

Pirtek ‘K’ Series

oils, ozone and weathering. Cover features a

Lay line example may not be a true indication

high level of abrasion resistance

of current status. Refer Pirtek for current information

Lay line example: Embossed text on a black abrasion resistant cover. Note: Comment above PIRTEK JETWASH 6.5 mm (1/4”) JW210A-04 210 BAR (3045 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code

Nominal ID

OD mm

Pressure bar

Min bend radius

Weight

Wire

Cover

working

min burst

Kg/m

6.4

1/4

11.1

13.4

210

840

0.20

JW210A-04 † † See Comments above

JW250 / JW250A JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

One braid of high tensile steel wire

-40°C up to +155°C † Comments:

Cover:

Not suitable for steam and hydraulic applications.

Hose Tails:

Pin pricked blue synthetic rubber resistant to

Lay line examples may not be a true indication

Pirtek ‘K’ Series all sizes

abrasion, oils, ozone and weathering. Specify

of current status. Refer Pirtek for current

JW250A for an even higher level of abrasion

information

resistance with black cover

Lay line example: Embosed text on blue cover (standard cover). Embossed text on black cover (abrasion resistant cover). Note: Comment above PIRTEK JETWASH 9.5 mm (3/8”) JW250-06 250 BAR (3625 PSI) WORK PRESS MAX 155°C PIRTEK JETWASH 6.5 mm (1/4”) JW250A-04 250 BAR (3625 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code

Nominal ID

OD mm

JW250-04 †

mm 6.4

in 1/4

Wire 9.9

JW250A-04 †

6.4

1/4

9.9

JW250-06 †

9.6

3/8

13.2

Pressure bar Cover 11.8

Min bend radius

Weight

working 250

min burst 1000

mm 60

Kg/m 0.16

11.8

250

1000

0.16

16.5

250

950

0.29

† See Comments above JWH-04 JWH-06

Blue strain reliever to suit JW250-04 & JW250A-04 hose Blue strain reliever to suit JW250-06 hose

JW400 / JW400A 2-WIRE JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

Two braid of high tensile steel wire

-40°C up to +155°C

Cover:

† Comments:

Hose Tails:

Pin pricked blue synthetic rubber resistant to

Not suitable for steam and hydraulic applications

Pirtek ‘K’ Series all sizes

abrasion, oils, ozone and weathering. Specify

Lay line examples may not be a true indication

JW400A for an even higher level of abrasion

of current status. Refer Pirtek for current

resistance with black cover

information

Lay line example: Embosed text on blue cover (standard cover). Embossed text on black cover (abrasion resistant cover). Note: Comment above

PIRTEK JETWASH 9.5 mm (3/8”) JW400-06 400 BAR (5800 PSI) WORK PRESS MAX 155°C PIRTEK JETWASH 69.5 mm (3/8”) JW400A-06 400 BAR (5800 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code

Nominal ID

OD mm

Pressure bar

Min bend radius

Weight

JW400-06 †

mm 9.5

in 3/8

Wire 14.8

Cover 16.8

working 400

min burst 1520

mm 90

Kg/m 0.44

JW400A-06 †

9.5

3/8

14.8

16.8

400

1520

0.44

† See Comments above

JWH-06

Blue strain reliever to suit JW400-06 and JW400A-06 hose

R1AT SINGLE WIRE BRAID

Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure hose for hydraulic fluids such

Tested in accordance with performance

Seamless NBR (Nitrile) rubber, oil resistant

as mineral oils, aqueous emulsions, water, air

specifications:

and inert gases

SAE100 R1AT S EN853 1SN

Reinforcement:

Temperature Range:

Approvals:

One braid of high tensile steel wire

-40Â°C up to +100Â°C mineral oil

AS2660 test requirements-

-40Â°C up to +60Â°C water based fluids

AS1180 10B and AS1180.13A (FRAS)

Cover:

0Â°C up to +60Â°C water

MSHA approved

0Â°C up to +50Â°C air

Prolonged usage with water or water based

Black synthetic rubber resistant to abrasion, oils,

-40Â°C up to +70Â°C ambient

fluids at temperatures above 70Â°C will allow

ozone and weathering

Cover must be pin pricked if hose is to be used

wire corrosion as a result of diffusion through the

to convey air above 17 bar

inner liner

Comment: Hose Tails:

Lay line example may not be a true indication of current status. Refer Pirtek for current

Pirtek â&#x20AC;&#x2DC;Kâ&#x20AC;&#x2122; Series to 5/8â&#x20AC;?

information.

Pirtek â&#x20AC;&#x2DC;Jâ&#x20AC;&#x2122; Series 3/4â&#x20AC;? to 2â&#x20AC;?

Lay line example: White text on black background. Note Comment above PIRTEK SAE 100R1 AT TYPE S R1AT-04 6.4 mm (1/4â&#x20AC;?) 225 BAR (3263 PSI) FRAS

Product Code

1 braid 1 braid 1 braid 1 braid

Cover 11.8 13.7 15.0 17.7

working 250 225 215 180

burst 1000 900 850 720

Min. bend radius mm 90 100 115 125

12.7

1 braid

20.8

160

640

180

0.45

15.9 19.1 25.4 31.8 38.1 50.8

1 braid 1 braid 1 braid 1 braid 1 braid 1 braid

23.6 28.0 36.2 47.6 54.0 68.3

140 105 88 63 50 40

560 420 352 252 200 160

201 240 300 420 500 630

0.50 0.62 0.93 1.36 1.70 2.43

Nominal Diameter

R1AT-03 â&#x20AC; R1AT-04 R1AT-05 â&#x20AC; R1AT-06

DN 5 6 8 10

ins 3/16 1/4 5/16 3/8

mm 4.9 6.4 7.9 9.5

R1AT-08

1/2

R1AT-10 R1AT-12 R1AT-16 R1AT-20 R1AT-24 R1AT-32

16 20 25 32 40 50

5/8 3/4 1 1 1/4 1 1/2 2

Reinforcement

OD mm

Pressure bar

Weight kg/m 0.18 0.23 0.27 0.37

â&#x20AC; Non-standard product. Available to special order

R1ATFS SINGLE WIRE BRAID FIRE SUPPRESSION APPROVAL Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure hose for hydraulic fluids

SAE J 517 (SAE 100R1AT)

Seamless synthetic rubber, resistant. to oil.

such as mineral and vegetable oils, aqueous

EN 853 1SN

emulsions and water.

Former DIN 20022 1SN (part 3) Meets hose requirements outlined in AS5062

Reinforcement:

Temperature Range:

One braid of high tensile steel wire.

-40°C up to +100°C (125°C intermittent)

Approvals: MSHA 2G in all sizes

Comment:

Approved within Australia for use on fire

Cover:

Lay line example may not be a true indication

suppression systems

Red synthetic rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

ozone and weathering

information.

Impulse Testing: All sizes tested to 150 000 cycles (hose only) Hose Tails: Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ Series 3/4”

Lay line example: White text on red background. Note Comment above PIRTEK R1ATFS — DIN EN 853 1SN 25mm (1”) R1AT-16 88 BAR (1,200 PSI) WORK. PRESS. MSHA

Nominal Diameter

Product Code

OD mm

Pressure bar

Min. bend radius

Weight

R1ATFS-04

DN 6

ins 1/4

mm 6.4

Wire 11.1

Cover 13.4

working 225

burst 900

mm 100

kg/m 0.23

R1ATFS-06

3/8

9.5

15.1

17.4

180

720

130

0.33

R1ATFS-08 R1ATFS-12

12 19

1/2 3/4

12.7 19.0

18.3 25.4

20.6 27.7

160 105

640 420

180 240

0.41 0.61

R2AT/2SC TWO WIRE BRAID

Construction

Applications

Inner Tube:

Medium to high pressure hose for hydraulic fluids Tested in accordance with performance

Reference Specifications

Seamless NBR (Nitrile) rubber, oil resistant

such as mineral oils, aqueous emulsions, water,

specifications:

air and inert gases

SAE100 R2AT

Reinforcement:

EN853 2SN

Two braids of high tensile steel wire

Temperature Range:

Approvals:

-40°C up to +100°C mineral oil

AS2660 test requirements-

-40°C up to +60°C water based fluids

AS1180.10B and AS1180.13A (FRAS)

Cover:

0°C up to +60°C water

MSHA approved

Black synthetic rubber resistant to abrasion, oils,

0°C up to +50°C air

Prolonged usage with water or water based

ozone and weathering

-40°C up to +70°C ambient

fluids at temperatures above 70°C will allow

Cover must be pin pricked if hose is to be used

wire corrosion as a result of diffusion through the

to convey air above 17 bar

inner liner

Comment:

Hose Tails:

Lay line example may not be a true indication

Pirtek ‘K’ Series to 5/8”

of current status. Refer Pirtek for current

Pirtek ‘J’ Series 3/4” to 3”

information.

954, 934 Series 2.1/2” to 3”

Lay line example: White text on black background. Note Comment above

PIRTEK SAE 100R2AT R2AT-12 19.1 mm (3/4”) 215 BAR (3118 PSI) FRAS

Product Code

Nominal Diameter

Reinforcement

OD mm

Pressure bar

Min. bend radius

Weight kg/m

ins

Cover

working

burst

R2AT-03 †

3/16

4.9

2 braids

13.4

415

1650

0.30

R2AT-04

1/4

6.4

2 braids

15.3

400

1600

100

0.37

R2AT-05 † R2AT-06 R2AT-08 R2AT-10 R2AT-12 R2AT-16 R2AT-20 R2AT-24 R2AT-32 R2AT-40 2SC-40 2SC-48 §

8 10 13 16 20 25 32 40 50 63 63 76

5/16 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2 2 1/2 2 1/2 3

7.9 9.5 12.7 15.9 19.1 25.4 31.8 38.1 50.8 63.5 63.5 76.2

2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids 2 braids

16.6 19.3 22.4 25.8 29.8 38.5 49.6 56.0 68.6 80.9 76.5 90.5

350 330 275 250 215 165 125 90 80 69 70 70 §

1400 1320 1100 1000 860 660 500 360 320 276 280 280

115 125 180 205 240 300 420 500 630 762 762 900

0.45 0.50 0.62 0.68 0.89 1.45 2.25 2.61 3.31 3.80 2.90 3.98

† Non standard product. Available to special order § Safety factor only 3.4:1 when used in conjunction with 934 Series hose tails Note: 2SC-40 and 2SC-48 hoses are not included in Standard EN857-2SC

R2ATHT TWO WIRE BRAID HIGH TEMP.

Construction

Applications

Reference Specifications

Inner Tube:

Hydraulic system service with petroleum,

Exceeds SAE J 517 (SAE 100R2AT)

High temp. elastomer rubber, resistant to oil

fire resistant and water base fluids, fuel and

EN 853 2SN

lubricating systems

Former DIN 20022 2SN (part 4)

Temperature Range:

Approvals:

Reinforcement:

-40°C up to +150°C

MSHA

Two braids of high tensile steel wire

except: air not to exceed 121°C

FRAS AS1180.10B &13A

: water not to exceed 70°C Comment:

Limitations:

Cover:

Lay line example may not be a true indication

Cover must be pin pricked if hose is to be used

Blue elastomer rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

to conduct air above 17 bar pressure

ozone and weathering

information.

Impulse Testing: All sizes tested to 200 000 cycles (hose only) Hose Tails: Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ Series 3/4” to 2”

Lay line example: White text on a dark blue layline. Note Comment above PIRTEK SAE 100 R2 AT — DIN EN 853 2SN “HIGH TEMP” 25mm (1”) R2ATHT-16 172 BAR (2494 PSI) WORK.PRESS: 150`C MAX MSHA-25 FRAS AS1180.10B & 13A

Product Code

Nominal Diameter

OD mm

Pressure bar

Min. bend radius

Weight

R2ATHT-04

DN 6

ins 1/4

mm 6.4

Wire 12.7

Cover 15.2

working 396

burst 1584

mm 102

kg/m 0.40

R2ATHT-06

3/8

9.5

16.7

19.2

345

1380

127

0.58

R2ATHT-08

1/2

12.7

19.8

22.1

293

1172

178

0.69

R2ATHT-10

5/8

15.9

23.0

25.1

224

896

203

0.81

R2ATHT-12

3/4

19.0

27.0

29.5

207

828

241

1.00

R2ATHT-16

25.4

34.9

37.8

172

688

305

1.45

R2ATHT-20

1 1/4

31.8

44.5

48.8

155

620

419

2.39

R2ATHT-24

1 1/2

38.1

50.8

54.6

120

480

508

2.59

R2ATHT-32

50.8

63.5

67.8

103

412

635

3.38

JH70 JACKING HOSE

Construction

Applications

Reference Specifications

Inner Tube:

High pressure hose for hydraulic fluids including

ISO 1307)

Seamless NBR (Nitrile) rubber, oil resistant

mineral and vegetable oil in hydraulic systems

Approvals:

for jacking applications

MSHA Approval No. IC-215/0

Temperature Range: Reinforcement:

Limitations:

-40°C up to +100°C mineral oil

Two braids of high tensile steel wire

+125°C intermittent

Only for use as jacking hose. Note reduced Safety Factor at 2:1

Comment: Cover:

Lay line example may not be a true indication

Hose Tails: Pirtek ‘K’ Series NM1E-0404K,

Black synthetic rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

NM1E-0604K & NM1E-0606K

ozone and weathering

information.

Use in conjunction with SRP Strain Relievers REFER to M.A.P.S. for WORK INSTRUCTION

;

Use ONLY NM1E-0404K, NM1E-0604K & NM1E-0606K Hose Tails and fit SRP Strain Relivers. Safety Factor is 2:1

Lay line example: Red text on black background. Note Comment above PIRTEK JACKING HOSE JH70-04 6.4mm (1/4”) 700 BAR (10152 PSI) MSHA IC-215/0 ABRASION RESISTANT

Product Code DN 6

JH70-04 JH70-06 %

(

)

10 +

Reinforcement

Nominal Diameter

(

OD mm

Pressure bar

Min. bend radius

Weight

ins 1/4

mm 6.4

2 braid

Cover 14.8

working 700

burst 1400

mm 80

kg/m 0.372

3/8

9.5

2 braid

19.0

700

1400

0.569

)

Use ONLY NM1E-0404K, NM1E-0604K & NM1E-0606K

JH70-06 assembly with Strain Reliever attached to resist kinking of the hose at the end of the Ferrule

SRP-04 Strain Reliever

SRP-06 Strain Reliever

C21 ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 210 bar working pressure to oil

JIS K6349-3

across all sizes) hose for hydraulic fluids such as mineral and vegetable oils, aqueous emulsions,

Approvals:

Reinforcement: 4 spirals of high tensile steel

water and inert gases

MSHA Approval No. IC-104/1 PAR No. 84844

wire

Prolonged usage with water or water based

FRAS AS1180.10B & 13A

fluids at temperatures above 70°C will allow Cover: Abrasion resistant black synthetic rubber

wire corrosion as a result of diffusion through the

Impulse Testing:

resistant to oils, ozone and weathering.

inner liner

Tested in accordance with SAE 100 R12 requirements

Temperature Range: -40°C up to +120°C mineral oil

Hose Tails: Pirtek ‘J’ or ‘X’ Series

-40°C up to +70°C water based fluids 0°C up to +70°C water -40°C up to +70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on black hose. Note Comment above. PIRTEK C21 50 mm (2”) C21-32 210 BAR (3,000 PSI) MSHA IC-104/1 ABRASION RESISTANT

Product Code C21-32

Nominal Diameter DN 51

ins 2”

OD mm mm 50.8

Wire 63.6

Cover 66.7

Pressure bar working 210

burst 840

Min. bend radius

Weight

Performance Standard

mm 500

kg/m 4.20

SAE R12

C25 ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 250 bar working pressure

Meets or exceeds SAE J 517 (100 R16)

to oil

across all sizes) hose for hydraulic fluids such as

Meets or exceeds EN 857 2SC

mineral and vegetable oils, aqueous emulsions,

Tested in accordance with SAE J517, EN856,

Reinforcement: Two braids of high tensile steel

water and inert gases

AS3791

wire, or 4 spirals of high tensile steel wire

Prolonged usage with water or water based

Approvals:

fluids at temperatures above 70°C will allow

MSHA Approval No. IC-104/1 PAR

Cover: Abrasion resistant black synthetic

wire corrosion as a result of diffusion through the

No. 84844 applies to all sizes

PVC nitrile rubber resistant to oils, ozone and

inner liner

FRAS AS1180.10B & 13A Impulse Testing:

weathering Temperature Range:

Braided hoses as per SAE 100 R16

Spiral hoses:

Spiral hoses as per SAE 100 R12

-40°C up to +120°C mineral oil -40°C up to +70°C water based fluids

Hose Tails:

0°C up to +70°C water

Pirtek ‘K’ Series to 5/8”

-40°C up to 70°C air

Pirtek ‘J’ Series 3/4”, 1”

Braided Hoses:

Pirtek ‘J’ or ‘X’ Series 1 1/4”, 1 1/2”

-40°C up to +100°C mineral oil -40°C up to +60°C water based fluids 0°C up to +60°C water -40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on black hose. Note Comment above PIRTEK C25 SERIES III 25mm (1”) C25-16 250 BAR (3,500 PSI) W.P. MSHA IC-104/1 ABRASION RESISTANT

Product Code C25-10 C25-12 C25-16 C25-20 C25-24

Nominal Diameter DN 16 19 25 31 38

ins 5/8 3/4 1 1 1/4 1/2

mm 15.9 19.0 25.4 32.2 38.5

Type

2 braid 2 braid 2 braid 4 spiral 4 spiral

OD mm Wire 23.0 26.2 32.9 43.9 48.8

Cover 25.2 29.1 35.6 47.0 53.5

Pressure bar working 280 250 250 250 250

burst 1120 1000 1000 1000 1000

Min. bend radius

Weight

mm 170 200 250 350 450

kg/m 0.80 1.00 1.30 2.70 3.20

PC28PS ISOBARIC CLASS HOSE ULTRA HIGH ABRASION RESISTANCE Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 275 bar working pressure

Meets or exceeds SAE J 517 (100 R12) for

to oil

across all sizes) hose for hydraulic fluids such as

impulse requirements

mineral and vegetable oils, aqueous emulsions,

Meets or exceeds JIS K6349

Reinforcement: 4 spirals of high tensile steel

water and inert gases

Tested in accordance with SAE J517, EN856,

wire

Prolonged usage with water or water based

AS3791

fluids at temperatures above 70°C will allow

Approvals:

Cover: Utmost abrasion resistant UHWMPE over wire corrosion as a result of diffusion through the

MSHA Approval No. IC104/1

black synthetic rubber, resistant to oils, ozone

AS2660 test requirements

and weathering Cover loss by abrasion when tested in accordance with ISO 6945 is 0.0 gram after 500,000 cycles

inner liner Improved bending radius for underground drilling machines

FRAS AS1180.10B & 13A Impulse Testing: Spiral hoses as per SAE 100 R12

Temperature Range:

Meets or exceeds JIS B8360 for heavy duty

-40°C up to +100°C mineral oil -40°C up to +70°C water based fluids 0°C up to +70°C water

applications Hose Tails:

-40°C up to 70°C air

Pirtek ‘J’ Series 1/2”, 3/4”, 1” (Refer Pirtek for current Fitting Series)

Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on black hose. Note Comment above PIRTEK PC28PS 25mm (1”) 280 BAR (4,000 PSI) W.P. FRAS MSHA IC104/1 ULTRA HIGH ABRASION RESISTANT

Product Code

Nominal Diameter

Type

OD mm

Pressure bar

Min. bend radius

Weight

PC28PS-08

DN 13

ins 1/2

mm 12.7

4 spiral

Wire 20.0

Cover 23.0

working 280

burst 1120

mm 110

kg/m 0.78

PC28PS-12 PC28PS-16

19 25

3/4 1

19.0 25.4

4 spiral 4 spiral

27.0 33.9

29.9 36.8

280 280

1120 1120

170 220

1.13 1.86

C35 ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 350 bar working pressure

Meets or exceeds SAE J 517 (100 R12, R13 or

to oil

across all sizes) hose for hydraulic fluids such as

R16)

mineral and vegetable oils, aqueous emulsions,

Meets or exceeds EN 857 2SC

Reinforcement: Two braids of high tensile steel

water and inert gases

Tested in accordance with SAE J 517, EN856,

wire, or 4-6 spirals of high tensile steel wire

Prolonged usage with water or water based

AS3791

fluids at temperatures above 70°C will allow

Approvals:

Cover: Abrasion resistant black synthetic

wire corrosion as a result of diffusion through the

MSHA Approval No. IC-104/1

PVC nitrile rubber resistant to oils, ozone and

inner liner

PAR No. 84844 on all sizes

weathering

Temperature Range:

FRAS AS1180.10B & 13A

Spiral hoses:

Impulse Testing:

-40°C up to +120°C mineral oil

Braided hoses as per SAE 100 R16 & R12

-40°C up to +70°C water based fluids

Spiral hoses as per SAE 100 R13

0°C up to +70°C water -40°C up to 70°C air

Hose Tails:

Braided hoses:

Pirtek ‘K’ Series to 5/8”

-40°C up to +100°C mineral oil

Pirtek ‘J’ Series 3/4”, 1”

-40°C up to +60°C water based fluids

Pirtek ‘X’ Series 1”, 1 1/4”, 1 1/2”,2”

0°C up to +60°C water

Interlock option 3/4” and above

-40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on braided hoses. Red text on spiral hoses. Note Comment above PIRTEK CLASS 35 9.5mm (3/8”) C35-06 350 BAR (5000 PSI) MSHA IC-104/1 ABRASION RESISTANT

Product Code C35-05 C35-06 C35-08 C35-10 † C35-12 C35-16 C35-20 C35-24 C35-32

Nominal Diameter DN

ins

8 10 12 16 19 25 31 38 51

5/16 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2

7.9 9.5 12.7 16.1 19.2 25.6 32.2 38.5 51.2

Type

2 braid 2 braid 2 braid 4 spiral 4 spiral 4 spiral 6 spiral 6 spiral 6 spiral

OD mm

Pressure bar

Min. bend radius

Weight

Wire

Cover

working

burst

kg/m

13.0 15.3 20.1 23.7 28.1 35.6 45.6 52.5 68.1

14.7 17.2 22.2 27.4 30.7 38.7 48.7 55.6 71.1

380 350 350 350 350 350 350 350 350

1520 1400 1400 1400 1400 1400 1400 1400 1400

85 90 130 200 220 280 380 480 600

0.34 0.42 0.62 1.00 1.50 2.20 3.70 4.40 6.90

† Meets or exceeds SAE100 R12 except for reinforcement OD

C42 ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 420 bar working pressure

Tested in accordance with SAE J517, EN856,

to oil

across all sizes) hose for hydraulic fluids such as

AS3791

mineral and vegetable oils, aqueous emulsions,

Approvals:

Reinforcement: Two braids of high tensile steel

water and inert gases

MSHA Approval No. IC-104/1 PAR No. 84844

wire (C42-04), or 4-6 spirals of high tensile steel

Prolonged usage with water or water based

(C42EH-32 has MSHA Approval IC-8/13)

wire

fluids at temperatures above 70°C will allow

FRAS AS1180.10B & 13A

wire corrosion as a result of diffusion through the Cover: Abrasion resistant black synthetic rubber

Impulse Testing:

inner liner

resistant to oils, ozone and weathering (PVC nitrile rubber on braided hoses)

Braided hoses as per SAE 100 R16 Temperature Range:

Spiral hoses as per SAE 100 R12, R15

Spiral hoses:

C42EH 2 Million Cycles applicable only in

-40°C up to +120°C mineral oil

conjunction with EH Series interlock tails

-40°C up to +70°C water based fluids 0°C up to +70°C water

Hose Tails:

-40°C up to 70°C air

Pirtek ‘K’ Series to 1/2”

Braided hoses:

Pirtek ‘J’ Series 3/8” and 1/2”

-40°C up to +100°C mineral oil

Pirtek ‘H’ Series 3/4”

-40°C up to +60°C water based fluids

Pirtek ‘X’ Series 3/4”, 1”

0°C up to +60°C water

Interlock 1” to 1.1/2”

-40°C up to 70°C ambient

Special Interlock for C42EH

Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on braided hoses. Yellow text on spiral hoses. Note Comment above

† MSHA Approval pending PIRTEK CLASS 42 19 mm (3/4”) C42-12 420 BAR (6,000 PSI) WORK.PRESS. MSHA IC-104/1 ABRASION RESISTANT PIRTEK CLASS 42 SERIES EH 50MM (2”) C42EH-32 420 BAR (6,000 PSI) EN856 MSHA IC-8/13 1Q09

Product Code C42-04 C42-06 C42-08 C42-12 C42-16 C42EH-20 C42EH-24 C42-32 C42EH-32

Nominal Diameter DN 6 10 12 19 25 31 38 51 51

ins 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 1 1/2 2

mm 6.4 9.7 12.9 19.2 25.7 32.2 38.5 51.2 51.2

OD mm

Type 2 braid 4 spiral 4 spiral 4 spiral 4 spiral 6 spiral 6 spiral 6 spiral 6 spiral

Wire 12.7 17.2 20.7 28.1 35.1 46.8 53.4 70.7 67.3

Pressure bar Cover 14.9 20.2 23.8 32.0 38.2 49.4 57.3 75.00 71.6

working 420 420 420 420 420 420 420 420 420

burst 1680 1680 1680 1680 1680 1680 1680 1680 1680

Min. bend radius

Weight

mm 75 125 180 280 300 420 500 600 630

kg/m 0.40 0.70 0.90 1.50 2.20 3.48 4.63 7.90 6.70

PC25 PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 250 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE 100R16 (braided hose)

Reinforcement:

inert gases

SAE 100R12 (spiral hose)

Two braids, or 4 spirals of high tensile steel wire

Excellent compact bend radius

Approvals:

Temperature Range:

AS2660 test requirements-

Cover:

Spiral hoses:

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistance black synthetic rubber

-40°C up to +120°C mineral oil

resistant to oils, ozone and weathering

-40°C up to +70°C water based fluids

Prolonged usage with water or water based

0°C up to +70°C water

fluids at temperatures above 70°C will allow

-40°C up to 70°C air

wire corrosion as a result of diffusion through the

Braided Hoses:

inner liner

-40°C up to +100°C mineral oil

Hose Tails:

-40°C up to +60°C water based fluids

Pirtek ‘K’ Series to 5/8”

0°C up to +60°C water

Pirtek ‘J’ Series 3/4”, 1”

-40°C up to 70°C ambient

Pirtek ‘J’ or ‘X’ Series 1 1/4”, 1 1/2”

Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on black background. Note Comment above PIRTEK PC25-12 19.1MM (3/4”) 250 BAR (3625 PSI) W.P. FRAS ABRASION RESISTANT

Product Code PC25-10 PC25-12 PC25-20 PC25-24

Nominal Diameter DN 16 20 32 40

ins 5/8 3/4 1 1/4 1/2

mm 15.9 19.1 31.8 38.1

Reinforcement

OD (mm)

2 braid 2 braid 4 spiral 4 spiral

26.0 29.1 44.9 52.4

Pressure bar W.P. 250 250 250 250

Min. Burst 1000 1000 1000 1000

Min. bend radius

Weight

mm 140 170 280 330

Kg/m 0.84 0.96 2.36 3.06

PC35 PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 350 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE R16 (braided hose)

Reinforcement:

inert gases

SAE 100 R12 (spiral hose)

Two braids, 4spirals or 6 spirals of high tensile

Excellent compact bend radius

SAE 100 R13 / R15 (spiral hose)

steel wire

Temperature Range:

Approvals:

Spiral hoses:

AS2660 test requirements-

Cover:

-40°C up to +120°C mineral oil

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistant black synthetic rubber

-40°C up to +70°C water based fluids

resistant to oils, ozone and weathering

0°C up to +70°C water

Prolonged usage with water or water based

-40°C up to +70°C ambient

fluids at temperatures above 70°C will allow

Braided hoses:

wire corrosion as a result of diffusion through the

-40°C up to +100°C mineral oil

inner liner

-40°C up to +60°C water based fluids Hose Tails:

0°C up to +60°C water -40°C up to 70°C ambient

Pirtek ‘K’ Series to 5/8”

Comment:

Pirtek ‘J’ Series 3/8” to 1”

Lay line example may not be a true indication

Pirtek ‘X’ Series 1” to 2”

of current status. Refer Pirtek for current

Pirtek Interlock Series 3/4” to 1.1/2”

information.

Lay line example: White text on black background. Note Comment above PIRTEK CLASS PC35-12 19.1MM (3/4”) 350 BAR (5076 PSI) FRAS ABRASION RESISTANT

Nominal Diameter

Product Code PC35-06 PC35-08 PC35-10 PC35-12 PC35-16 PC35-20 PC35-24

Reinforcement

ins

10 13 16 20 25 32 40

3/8 1/2 5/8 3/4 1 1 1/4 1 1/2

9.5 12.7 15.9 19.1 25.4 31.8 38.1

2 braids 4 spirals 4 spirals 4 spirals 4 spirals 6 spirals 6 spirals

O.D. mm

18.9 22.2 26.4 36.6 36.6 48.7 55.6

Pressure bar

Min. bend radius

Weight

W.P.

Min. Burst

Kg/m

350 350 350 350 350 350 350

1400 1400 1400 1400 1400 1400 1400

90 110 140 170 220 280 330

0.55 0.80 1.00 1.13 2.00 3.80 4.60

PC42 PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 420 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE 100 R16 (braided hose)

Reinforcement:

inert gases

Approvals:

Two braids of high tensile steel wire

Excellent compact bend radius

AS2660 test requirements-

Cover:

Temperature Range:

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistance black synthetic rubber

Spiral hoses:

resistant to oils, ozone and weathering

-40°C up to +120°C mineral oil

Prolonged usage with water or water based

-40°C up to +70°C water based fluids

fluids at temperatures above 70°C will allow

0°C up to +70°C water

wire corrosion as a result of diffusion through the

-40°C up to 70°C ambient

inner liner.

Braided hoses: -40°C up to +100°C mineral oil

Hose Tails:

-40°C up to +60°C water based fluids

Pirtek ‘K’ Series

0°C up to +60°C water -40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on black background. Note Comment above PIRTEK CLASS PC42-04 6.4 MM (1/4”) 420 BAR (6091 PSI) FRAS ABRASION RESISTANT

Product Code PC42-04

Nominal Diameter DN 6

ins 1/4

Reinforcement mm 6.4

2 braids

OD (mm) 14.9

Pressure (bar) W.P. 420

Min. Burst 1680

Min. bend radius

Weight

mm 70

Kg/m 0.39

C45 ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Synthetic rubber, resistant to oil

High pressure hose for hydraulic fluids such as

Tested in accordance with performance

mineral oils, aqueous emulsions, vegetable oils,

specifications:

Reinforcement: 4 spirals of high tensile steel

water, air and inert gases.

DIN EN 856 4SH

wire

Especially used for “Dynapac” style rollers. NOTE: THIS HOSE MUST ONLY BE USED FOR

Cover: Abrasion resistant black synthetic rubber

STATIC APPLICATIONS – Not recommended for

Approvals:

resistant to oils, ozone and weathering.

impulsing applications

MSHA Approval No. IC-188

Temperature Range: -40°C up to +100°C mineral oil

Hose Tails:

-40°C up to +60°C water based fluids

Pirtek ‘B’ Series

0°C up to +60°C water

(2-piece system requires a separate SFB ferrule)

-40°C up to +70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: Orange text on black background. Note Comment above PIRTEK CLASS 45 C45-10 15.9mm (5/8”) 450 BAR (6500 PSI) MSHA

Product Code C45-10

Nominal Diameter DN 16

ins 5/8

mm 15.9

Reinforcement

4 spiral

O.D. Cover mm 28.5

Pressure bar working 450

burst 1800

Min. bend radius

Weight

mm 250

kg/m 1.30

JBF LARGE BORE HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic

Medium pressure hose for hydraulic fluids

SAE J517 except for reinforcement OD

rubber, resistant. to oil

such as mineral and vegetable oils, aqueous Approvals:

emulsions and water Reinforcement: Four spirals of high

MSHA Approval No. IC-104/1 PAR No. 84844

tensile steel wire.

Prolonged usage with water or water based

FRAS AS1180.10B & 13A

fluids at temperatures above 70°C will allow Cover: Abrasion resistant black synthetic rubber

wire corrosion as a result of diffusion through the

resistant to oils, ozone and weathering

inner liner Temperature Range: -40°C up to +100°C mineral oil

Hose Tails: Pirtek

-40°C up to +70°C water based fluids

‘BSMS’ Series

0°C up to +70°C water -40°C up to 70°C air / ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: Light yellow text on black hose. Note Comment above PIRTEK JUMBO ACE 63mm (2 1/2”) JBF-40 140 BAR (2030 PSI) WP MSHA IC/104/1 FRAS ABRASION RESISTANT

Product Code JBF-40

Nominal Diameter DN 63

ins 2.1/2

Type mm 63.5

4 spiral

OD mm Cover 82.4

Pressure bar working 140

burst 560

Min. bend radius mm 660

Weight kg/m 5.5

Test Impulses No. 500 000

LPG LP GAS AS1869 CLASS D

Construction

Applications

Reference Specifications

Inner Tube:

High pressure hose for transfer of natural

Meets and / or exceeds:

Conductive Teflon®

gas, town gas, LPG, and butane-propane on

AS1869 Class D

stationary and mobile LPG gas engines. Ideal

Very low extractables and permeation rate.

Reinforcement:

for forklift, automotive, light & medium duty truck

Approvals:

Single braid of stainless steel wire

and transfer

AGA (Aust. Gas Association)

Cover:

Temperature Range:

Black and blue fire retardant, abrasion resistant

-20°C up to +125°C

aramid polyester

Comment:

Pirtek ‘G’ Series

Lay line example may not be a true indication

Special procedures apply using dedicated

of current status. Refer Pirtek for current

dies and spacers.

information.

Thermoplastic tag required on all hose

Hose Tails:

assemblies.

Lay line example: Hose does not have layline. Note Comment above

Product Code LPG-06 LPG-10†

Nominal Diameter DN 10 16

ins 5/16 1/2

mm 7.9 12.7

Reinforcement

OD (mm)

1 wire braid 1 wire braid

13.6 19.1

Pressure (bar) W.P. 26 26

Min. Burst 104 104

Min. bend radius

Weight

mm 101.6 165.1

Kg/m 0.18 0.27

† Limited stock available

R12C SPIRAL SAE100 R12 HOSE

Construction

Applications

Reference Specifications

Inner Tube: Fabric reinforced synthetic rubber,

High pressure hose for hydraulic fluids such as

SAE J 517 (100 R12)

resistant to oil

glycol, mineral oils, fuels, hydrocarbons etc.

EN 856 R12

Designed for applications where flexibility and Reinforcement: Four spirals of high tensile steel

high temperature resistance are required.

Approvals:

wire separated by layers of synthetic rubber

Compatible with Caterpillar® reusable fittings.

US MSHA IC-101

Temperature Range:

Impulse Testing:

-40°C up to +121°C mineral oil

1 000 000 impulses @ 133% of working pressure

Cover: Black synthetic rubber resistant to abrasion, oils, ozone and weathering

for all sizes. Additionally, hose is aged by heating Comment:

and cooling prior to testing. Hose only

Lay line example may not be a true indication of current status. Refer Pirtek for current

Hose Tails:

information

Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ or ‘X’ Series 3/4” upwards Caterpillar® re-useable

Lay line example: Yellow text on black hose. Note Comment above XT® Technology SAE 100R12 ¾” Max WP 4000psi MSHA IC-101/10 Made in USA

Product Code R12C-06 R12C-08 R12C-10 R12C-12 R12C-16 R12C-20 R12C-24 R12C-32

Nominal Diameter DN 10 12 16 19 25 31 38 51

ins 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2

OD mm

Type mm 9.5 13 16 19 25 32 38 51

4 spiral 4 spiral 4 spiral 4 spiral 4 spiral 4 spiral 4 spiral 4 spiral

Wire 17.2 20.7 24.6 27.6 34.9 43.9 50.4 63.6

Cover 20.2 23.8 27.2 30.7 38 47 53.4 66.7

Pressure bar working 276 276 276 276 276 207 172 172

burst 1104 1104 1104 1104 1104 828 688 688

Min. Bend Radius mm 64 89 102 121 153 210 254 318

Weight kg/m 0.70 0.83 1.20 1.43 2.00 2.80 3.40 4.25

R13C SPIRAL SAE100 R13 HOSE

Construction

Applications

Reference Specifications

Inner Tube: Fabric reinforced synthetic rubber,

Very high pressure hose for hydraulic fluids such

SAE J 517 (100 R13)

resistant to oil

as glycol, mineral oils, fuels, hydrocarbons etc.

EN 856 R13

Reinforcement: Four or six spirals of high

Specifically designed for applications where

Approvals:

tensile steel wire separed by layers of synthetic

high pulsating pressure, flexibility and high

US MSHA IC-101

rubber

temperature resistance are required. Compatible

Cover: Black synthetic rubber resistant to

with Caterpillar® reusable fittings

Impulse Testing:

abrasion, oils, ozone and weathering.

1 000 000 impulses @ 120% of working pressure Temperature Range:

for all sizes. Additionally, hose is aged by heating

-40°C up to +121°C mineral oil

and cooling prior to testing. Hose only

Comment:

Hose Tails:

Lay line example may not be a true indication

Pirtek ‘X’ Series all sizes

of current status. Refer Pirtek for current

Interlock option 1 1/4” upwards

information

Caterpillar® re-useable

Lay line example: Red text on black hose. Note Comment above XT® Technology SAE 100R13 1” Max WP 5000psi MSHA IC-101/10 Made in USA

Product Code R13C-12 R13C-16 R13C-20 R13C-24 R13C-32

Nominal Diameter DN 19 25 31 38 51

ins 3/4 1 1.1/4 1.1/2 2

OD mm

Type mm 19 25 32 38 51

4 spiral 4 spiral 6 spiral 6 spiral 6 spiral

Wire 29.0 35.6 46.8 54.3 68.1

Cover 32.1 38.7 49.8 57.3 71.1

Pressure bar working 345 345 345 345 345

burst 1380 1380 1380 1380 1380

Min. Bend Radius mm 141 153 210 254 318

Weight kg/m 1.75 2.30 3.70 4.65 6.90

WB1000 WATERBLAST HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Very high constant pressure hose for water

AS/NZS 4233.2

Synthetic rubber, resistant. to oils

scaling systems. Suitable for passage of water and aqueous solutions

Reinforcement:

Temperature Range:

Four spirals of high tensile steel wire

-40°C up to +80°C

Cover:

Comment:

Hose Tails:

Black synthetic rubber extremely resistant to

Lay line example may not be a true indication

I / IFWB (Interlock)

abrasion, oils, and weathering

of current status. Refer Pirtek for current information

Lay line example: Moulded into outer cover. Note Comment above PIRTEK® WATERBLAST 3/4” DN19 W.P. 1000 BAR B.P. 2500 BAR

Product Code WB1000-12 Y

[

]

Nominal ID DN 19

mm 19

OD mm in 3/4

Wire 29.0

Cover 32

Pressure bar working 1000

min burst 2500

Min bend radius mm 250

Weight Kg/m 1.73

Alternative Product Code WB2-12

WB1100 WATERBLAST HOSE Construction

Applications

Reference Specifications

Inner Tube:

Very high constant pressure hose for water

AS/NZS 4233.2

Synthetic rubber, resistant. to oils

scaling systems. Suitable for passage of water and aqueous solutions

Reinforcement:

Temperature Range:

Four spirals of high tensile steel wire

-40°C up to +80°C

Cover:

Comment:

Hose Tails:

Black synthetic rubber extremely resistant to

Lay line example may not be a true indication

I / IFWB (Interlock)

abrasion, oils, and weathering

of current status. Refer Pirtek for current information

Lay line example: Moulded into outer cover. Note Comment above

PIRTEK® WATERBLAST 1/2” DN12 W.P. 1100 BAR B.P. 2750 BAR

Product Code WB1100-08

Wire

Cover

working

min burst

Min bend radius mm

12.7

1/2

21.5

24.5

1100

2750

230

Nominal ID

OD mm

Pressure bar

4523 HAND CUTTER SUIT AUTO AND AIR CON HOSES, SYNFLEX, NYLON ETC 4523 Hand Cutting Tool Product Code

Description

4523-04006

Hand Cutter for Hose and Tube - New Style

4523-04005

Replacement Blade for Hand Cutter 4523-04006

• A robustly made hand cutting tool for cleanly cutting a wide range of hose and tube products • Replaceable blade

Weight Kg/m 1.12

30CT BROAD SPECTRUM HOSE Construction

Applications

Reference Specifications

Inner Tube:

Flexible even in cold temperatures. Small outside Exceeds SAE J517 (R18)

composite wall dual extrusion smooth seamless

diameter and good flexibility over sheaves

SAE J343 Test procedures

polymeric (polyester) inner and polyurethane

allows use over a wide range of forklift sheaves,

ASTM D-380 Testing Rubber hoses

adjacent

including freezer applications.

ASTM D-622 Testing for Automotive Brake

Other applications include construction, general

Systems

hydraulics, chemical and gas transfer, machine tools, agricultural equipment etc Reinforcement:

Temperature Range:

Impulse Testing:

braided synthetic fibre in either single or dual

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

layer

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids

Volumetric Expansion: Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details

Cover:

Comment:

Hand Cutter:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Hand Cutting Tool (see below) makes light work

bonded to the reinforcement

of current status. Refer Pirtek for current

of cutting Synflex hoses

information

Hose Tails: Pirtek ‘S7’ or ‘S18’ Series (refer Table for Die) Pirtek ‘T’ Series option

Lay line example: White text on black hose. Note Comment above SYNFLEX® 30CT-06 SAE 100R18 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Nominal ID

Product Code 30CT-04 30CT-05 30CT-06 30CT-08 30CT-10

DN 6.4 8 9.5 12.7 16

mm 1/4 5/16 3/8 1/2 5/8

OD in 6 8 10 12 16

mm 12.1 15.5 16.8 21.6 27

Pressure bar working 207 207 207 207 207

min burst 828 828 828 828 828

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 32 38 51 89 102

Kg/100m 8.9 14.7 18.2 24.7 41.4

Die 45403W4 305 306 A0800 N10

Series S7 S7 S7 S7 S18

3JET WATER JETTING HOSE

Construction

Applications

Inner Tube:

Medium pressure hose for water jetting and drain ISO 7751

Reference Specifications

Smooth seamless thermoplastic (nylon)

cleaning. Low elongation

Reinforcement:

Temperature Range:

Hand Cutter:

Spiral or braided synthetic fibre

-40°C up to +66°C water

Hand Cutting Tool (see page 37) makes light work of cutting Synflex hoses

Cover:

Comment:

Hose Tails:

Black, perforated bonded polyurethane

Lay line example may not be a true indication

Pirtek ‘S7’ series (refer below table for dies)

of current status. Refer Pirtek for current

Pirtek ‘T’ series

information

Lay line example: White text on black hose. Note Comment above PIRTEK PIRJET 3JET-03 4.9mm (3/16”) 331 BAR (4800 PSI) WATER JETTING 04/13 / - / / -

Nominal ID

Product Code 3JET-03 3JET-04

DN 5 6

mm 3/16 1/4

OD in 4.9 6.4

mm 10.8 13.0

Pressure bar working 331 331

min burst 827 827

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 19 32

Kg/100m 6.8 8.5

Die 4540303 304

Series S7 S7

30CTX2 / 30CTX3 MULTI-LINE BROAD SPECTRUM HOSE

Construction

Applications

Inner Tube:

Flexible even in cold temperatures. Small outside Exceeds SAE J517 (R18)

Reference Specifications

composite wall dual extrusion smooth seamless

diameter and good flexibility over sheaves

SAE J343 Test procedures

polymeric (polyester) inner and polyurethane

allows use over a wide range of forklift sheaves,

ASTM D-380 Testing Rubber hoses

adjacent

including freezer applications.

ASTM D-622 Testing for Automotive Brake

Other applications include construction, general

Systems

hydraulics, chemical and gas transfer, machine tools, agricultural equipment etc Reinforcement:

Temperature Range:

Impulse Testing:

braided synthetic fibre in either single or dual

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

layer

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids

Volumetric Expansion: Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details

Cover:

Comment:

Hand Cutter:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

bonded to the reinforcement

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S7’ or ‘S18’ Series (refer Table for Die) Pirtek ‘T’ Series option

Lay line example: White text on black hose. Note Comment above SYNFLEX® 30CT-06 SAE 100R18 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Product Code

No. of Lines

Nominal ID DN

Pressure bar

Min bend radius

Synflex Die and Hose Tail Combination Kg/100m Die 4540- Series Weight

working

min burst

30CTX2-04 2 6.4 1/4 30CTX2-05 2 8 5/16 30CTX2-06 2 9.5 3/8 30CTX2-08 2 12.7 1/2 30CTX2-10 † 2 16 5/8 SPECTRA 30CT TRI-LINE 30CTX3-05 3 8 5/16 † Non-standard product. Available to special order

6 8 10 12 16

12.1 15.5 16.8 21.6 27.0

207 207 207 207 207

828 828 828 828 828

32 38 51 89 102

8.9 14.7 18.2 24.7 41.4

3W4 305 306 A0800 N10

S7 S7 S7 S7 S18

15.5

207

828

24.1

305

3130 MEDIUM PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulics, high pressure gas transfer,

SAE J517 (R7)

smooth seamless thermoplastic (nylon)

chemical transfer. Low elongation, best value

SAE J343

100R7 hose.

ASTM D-380

Not for use over pulleys.

ASTM D-622

Absorbs shock loads and damaging pressure spikes through controlled expansion. Reinforcement:

Temperature Range:

Impulse Testing:

spiralled or braided synthetic

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only) at 133% WP Cover:

Comment:

Hand Cutter:

Perforated bonded black polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S7’ Series (refer Table for Die) Pirtek ‘T’ Series option

Lay line example: White text on black hose. Note Comment above SYNFLEX® 3130-06 SAE 100R73/8” W.P 2250 P.S.I. (155 BAR) SAINT-GOBAIN

Nominal ID

Product Code

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

3130-02 3130-03 3130-04 3130-05 3130-06

DN 3 5 6 8 10

mm 1/8 3/16 1/4 5/16 3/8

in 3.2 5 6.4 8 9.5

mm 8.5 10.8 13.0 15.1 17.0

working 172 207 207 172 155

min burst 689 827 827 689 620

mm 13 19 32 45 51

Kg/100m 3.87 6.70 9.08 11.16 12.5

Die 4540302 303 304 305 306

Series S7 S7 S7 S7 S7

3130-08

1/2

12.7

20.7

138

552

76.2

16.97

308

3130-12 3130-16

20 25

3/4 1

19 25.4

27.1 34.0

86 69

345 276

127 203

26.19 46.28

312 316

S7 S7

3360X2 TWIN-LINE FOR FORKLIFTS

Construction

Applications

Reference Specifications

Inner Tube:

Flexible even in cold temperatures.

SAE 100R17

Nylon

Small outside diameter and good flexibility over sheaves allows use over a wide range of forklift sheaves, including freezer applications. Other applications include construction, general hydraulics, chemical and gas transfer, machine tools, agricultural equipment etc.

Reinforcement:

Temperature Range:

Impulse Testing:

braided synthetic fibre

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids Volumetric Expansion (per line): Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details Cover:

Comment:

Hand Cutter:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S8’ (refer Table for Die) Pirtek ‘200/SN8’ Series option

Lay line example: White text on black hose. Each line is branded as though a single line. Note Comment above SYNFLEX® 3360-06 SAE 100R17 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Nominal ID

Product Code 3360X2-06 †

DN 9.5

mm 3/8

OD in 10

mm 18.4

Pressure bar working 207

min burst 828

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 51

Kg/100m 56.8

Die 4540J06N

Series S8

† Please note that this hose is available on an indent only basis

37AL NON-CONDUCTIVE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

ANSI A92.2 for Vehicle Mounted Aerial Devices

polyester core tube

voltage sources.

SAE J517 Non-conductive hose

Aerial equipment

Construction

Mobile hydraulics

SAE 100R7

Rescue apparatus and tools Reinforcement:

Temperature Range:

Features:

braided synthetic fibre

-54°C up to +100°C

SAE J517 non conductive hose construction.

except max. 60°C with water based or fire

Less than 50 microamperes leakage when

resistant fluids

subjected to 75,000 volts/foot for 5 minutes. Flexible at low temperatures Abrasion resistant cover Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) at 133% WP

Cover:

Comment:

Hand Cutter:

orange non-perforated non stick polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S7’ Series (refer Table for Die) Pirtek ‘T’ Series option Lay line example: Black text on orange hose. Note Comment above SYNFLEX® 37AL-04 NON-CONDUCTIVE SAE 100R7 1/4” I.D. 2750 PSI W.P. (190 BAR) ANSI A92-2 3000 PSI W.P. (207 BAR). USE DIE 4540-3W400

Product Code 37AL-03 † 37AL-04 37AL-05 † 37AL-06 37AL-08

Nominal ID

5 6 8 10 12

3/16 1/4 5/16 3/8 1/2

4.8 6.4 7.9 9.5 12.7

10.8 12.3 14.7 16.1 20.7

Min bend radius

Weight

Synflex Die and Hose Tail Combination

min burst

Kg/100m

Die 4540-

Series

827 759 689 620 620

19 32 44 51 76

7.1 8.9 11.2 14.1 21.3

303 3W4 305 306 308

S7 S7 S7 S7 S7

Pressure bar working ANSI R7 207 207 207 190 207 172 207 155 207 155

† Non-standard product. Available to special order

37ALX2 TWIN-LINE NON-CONDUCTIVE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

ANSI A92.2 for Vehicle Mounted Aerial Devices

polyester core tube

voltage sources.

SAE J517 Non-conductive hose

Aerial equipment

Construction

Mobile hydraulics

SAE 100R7

Rescue apparatus and tools Reinforcement:

Temperature Range:

Features:

braided synthetic fibre

-54°C up to +100°C

SAE J517 non conductive hose construction.

except max. 60°C with water based or fire

Less than 50 microamperes leakage when

resistant fluids

subjected to 75,000 volts/foot for 5 minutes. Flexible at low temperatures Abrasion resistant cover Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) at 133% WP

Cover:

Comment:

Hand Cutter:

orange non-perforated non stick polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

Nominal ID

Product Code 37ALX2-04 37ALX2-06 37ALX2-08

6 10 12

1/4 3/8 1/2

6.4 9.5 12.7

12.3 16.1 20.7

Min bend radius

Weight

Synflex Die and Hose Tail Combination

min burst

Kg/100m

Die 4540-

Series

759 620 620

32 51 76

17.8 28.2 42.6

3W4 306 308

S7 S7 S7

Pressure bar working ANSI R7 207 190 207 155 207 155

3800 HIGH PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems

SAE 100 R8 performance with SAE 100R7

nylon core tube

High pressure gas and chemical transfer

dimensions

Machine tools Mobile equipment Marine steering Compatable with oxygen & breathing air mixtures Reinforcement:

Temperature Range:

Impulse Testing:

braided high tensile aramid fibre (Kevlar)

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only) Cover:

Comment:

Hand Cutter:

black perforated non stick polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S7’ Series (refer Table for Die)

Lay line example: White text on black hose. Note Comment above

SYNFLEX® 3800-04 SAE 100R81/4” W.P 5000 P.S.I. (345 BAR) SAINT-GOBAIN

Nominal ID

Product Code

3800-02 3800-03 3800-04 3800-06 3800-08 3800X2-04 †

DN 3 5 6 10 12 6

in 1/8 3/16 1/4 3/8 1/2 1/4

mm 3.2 4.8 6.4 9.5 12.7 6.4

3800X2-06 †

3/8

9.5

3800X2-08 †

1/2

12.7

mm 8.5 11.0 13.5 16.9 21.3 13.5

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 20 38 51 64 102 51

Kg/100m 4.0 8.3 11.8 15.8 21.7 23.6

Die 4540302 303 304 306 308 304

working 414 345 345 276 241 345

min burst 1656 1379 1379 1103 965 1379

16.9

276

1103

31.6

306

21.3

241

965

102

43.4

308

† Non-stocked item. Available to special order

Series S7 S7 S7 S7 S7 S7

3E80 NON-CONDUCTIVE HIGH PRESSURE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

SAE 100 R8

smooth seamless nylon

voltage sources.

SAE J517 non-conductive construction

Aerial equipment. Mobile hydraulics. Rescue apparatus and tools Reinforcement:

Temperature Range:

Features:

braided synthetic fibre

-40°C up to +100°C

SAE J517 non conductive hose construction.

Max 66°C with water-based or fire resistant fluids Less than 50 microamperes leakage when subjected to 75,000 volts/foof for 5 minutes Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) Cover:

Comment:

Hand Cutter:

Orange non stick non-perforated polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S8’ Series (refer Table for Die) Lay line example: Black text on orange hose. Note Comment above

SYNFLEX® 3E80-06 SAE 100R8 3/8” W.P 4000 P.S.I. (276 BAR) NON CONDUCTIVE FURON

Nominal ID

Product Code

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

3E80-04 3E80-06

DN 6 10

mm 1/4 3/8

in 6.4 9.5

mm 15.9 19.5

working 345 276

min burst 1379 1103

mm 51 64

Kg/100m 17.6 22.0

Die 4540H04 H06

Series S8 S8

3E80-08

1/2

12.7

22.7

241

965

102

28.3

H08

3R80 HIGH PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems

SAE 100 R8

smooth seamless nylon

High pressure pneumatic systems Machine tools Mobile equipment Mobile hydraulics Compatable with oxygen & breathing air mixtures

Reinforcement:

Temperature Range:

Impulse Testing:

braided synthetic fibre

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only) Cover:

Comment:

Hand Cutter:

black perforated non stick polyurethane

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘S8’ Series (refer Table for Die)

Lay line example: White text on black hose. Note Comment above SYNFLEX® 3R80-08 SAE 100R8 1/2” W.P 3500 P.S.I. (241 BAR) SAINT GOBAIN

Nominal ID

Product Code

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

3R80-03 3R80-04 3R80-06 3R80-08 3R80-12

DN 5 6 10 12 19

mm 3/16 1/4 3/8 1/2 3/4

in 4.8 6.4 9.5 12.7 19.1

mm 13.1 15.9 19.5 22.7 28.9

working 345 345 276 241 155

min burst 1379 1379 1103 965 620

mm 38 51 64 102 165

Kg/100m 11.5 17.6 22.0 28.3 38.1

Die 4540H03 H04 H06 H08 H12

Series S8 S8 S8 S8 S8

3R80-16

25.4

37.4

138

552

254

57.3

H016

3VEO NON-CONDUCTIVE JACKING HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

Meets SAE 100 R8

smooth seamless nylon

voltage sources.

SAE J517 Non-Conductive Hose Construction

Aerial equipment. Mobile hydraulics. Rescue apparatus and tools. Reinforcement:

Temperature Range:

Features:

spiralled high tensile aramid fibre (Kevlar)

-40°C up to +66°C

High WP 8000—10000 psi (551–689 bar) Compact size with low elongation Less than 50 microamperes leakage when subjected to 75,000 volts/foot for 5 minutes.

Cover:

Comment:

Hand Cutter:

Orange non stick non-perforated

Lay line example may not be a true indication

Hand Cutting Tool (see page 37) makes light

polyurethane. (See note)

of current status. Refer Pirtek for current

work of cutting Synflex hoses

information Hose Tails: Pirtek ‘SV’ Series Special procedures apply. Assemblies only to be made by trained personnel listed on the Qualified Personnel Register Guards and warning tags are required on the completed assembly

Lay line example: White text on orange hose. Note Comment above

SYNFLEX® 3VEO-04 SAE 1/4” I.D. W.P 10,000 P.S.I. (690 BAR) (NON CONDUCTIVE) PAT. NO. 4343333

Nominal ID

Product Code 3VEO-04 3VEO-06

DN 6 10

mm 6.3 9.5

OD in 1/4 3/8

mm 14.0 17.4

Pressure bar working 689 551

min burst 2758 2205

Min bend radius

Weight

mm 64 76

Kg/m 0.158 0.244

3VEO hose assemblies are available only as completed assemblies from accredited assemblers. Each assembly comprises : 3VEOhose Pirtek SV Series couplings Hose guard Identity Tag 3VE0-04 assemblies complete with 3/8” NPT male ends are available in 6 standard configurations. Other configurations upon request Product Code Length 3VEO04-06-1

1 metre long

3VEO04-06-2 3VEO04-06-3

2 metres long 3 metres long

3VEO04-06-4 3VEO04-06-5

4 metres long 5 metres long

3VEO04-06-6

6 metres long s

STH PTFE (TEFLON) HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure and laundry equipment

SAE 100 R14

extruded seamless smooth bore Teflon

Plastic moulding presses Hazardous chemicals Steam and compressor discharge

Reinforcement:

Temperature Range:

Features: A graphite impregnated (black)

AISI 304 stainless steel single wire braid

-54°C up to +230°C* (see notes below)

Teflon liner is available to special order for applications requiring a core tube capable of safely conducting static electricity. Consult Pirtek for details Impulse Testing: No information available

Cover:

Comment:

The reinforcement braid serves as the outer

No lay line present due to the stainless steel

cover

braid

Nominal ID

Product Code

in 3/16 3/16

Hose Tails:

Average OD

Wall Thickness

mm 6.3 7.6

mm 1.0 1.4

Pirtek ‘T’ Series

Pressure bar working 241 206

min burst 965 828

Min bend radius

Vacuum Service

mm 25 50

bar 0.9 0.9

STH-02 STH-03

Braiding 1 Braid 1 Braid

mm 3.9 4.8

STH-04

1 Braid

6.35

1/4

9.5

1.57

206

828

0.9

STH-05

1 Braid

7.94

5/16

10.9

1.48

172

692

100

0.9

STH-06 +

1 Braid

9.5

3/8

12.8

1.65

138

552

125

0.9

STH-08 +

1 Braid

12.7

1/2

16.3

1.80

120

484

165

0.9

STH-10 +

1 Braid

15.9

5/8

19.2

1.65

103

416

187

0.9

STH-12 +

1 Braid

19.05

3/4

22.6

1.78

276

212

0.4

STH-16 +

2 Braid

25.4

30.9

2.75

276

225

0.4

+ Use of an internal support coil for hoses -06 and larger is recmmended for tube support where continuous or extended service at high temperature together with low or negative pressure is expected

Not recommended for steam / cold water cycling

*For temperatures above 120°C Pressure: Reduce working pressure by 1% per additional degree C. Vacuum: Reduce vacuum rating by 1.5% per additional degree C. Note: The minimum bend radius quoted is for a static bend at ambient temperature. Dynamic bending, especially at elevated temperatures, will increase the minimum bend radius accordingly. Consult Pirtek for specific applications

TECHNICAL DATA SUMMARY OF PIRTEK HYDRAULIC HOSE MATERIALS Product Code

Description

Liner Material

Cover Material

Two wire braid hose 210 bar four spiral hose 250 bar four spiral hose 350 bar braid or spiral hose 420 bar braid or spiral hose 450 bar spiral hose high flexibility Engine & air brake hose FRAS rated Air / Water Stone Hose FRAS Air Water Suction & Delivery Oil suction hose Large bore four spiral hose Jacking Hose 210 bar jet wash hose 250 bar jet wash hose

NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class IV) NBR (Class IV)

NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) NBR (Class I) CR CR SBR NBR (Class I) NBR (Class I) NBR (Class IV) NBR (Class IV)

JW400

400 bar jet wash hose

NBR Class IV)

RUBBER

2SC C21 C25 C35 C42 C45 HTAB / HTFH IRFAW IRFWSDH IROFSD JBF JH70 JW210 JW250 LPG

Teflon

NBR (Class I)

Multi purpose oil and air hose

NBR (Class I)

High abrasion resistance 250 bar hose

NBR (Class I)

High abrasion resistance 280 bar hose

NBR (Class I)

PC35

High abrasion resistance 350 bar hose

NBR (Class I)

PC42

High abrasion resistance 420 bar hose

NBR (Class I)

R1AT

One wire braid hose

NBR (Class I)

R1ATFS

One wire fire suppression hose

NBR (Class I)

R2AT

Two wire braid hose

NBR (Class I)

R2ATHT

High Temp. two wire braid hose

NBR (Class IV)

R4HT R5HT

High Temp. Hydraulic Suction / Delivery High Temp. Air Brake Hose

NBR (Class IV) NBR (Class IV)

NBR (Class IV) Polyester

Low pressure hydraulic hose

NBR (Class I)

R12C

SAE 100R12 spiral hose

NBR (Class II)

R13C

SAE 100R13 spiral hose

NBR (Class II)

WB1000

1000 bar water blast hose

NBR (Class III)

WB1100

1100 bar water blast hose

NBR (Class III)

3130

General purpose SAE 100R7

Nylon

Polyurethane

3800

Compact SAE 100R8

Nylon

Polyurethane

High pressure non-conductive

Nylon

Polyurethane

Cold temperature hose

Polyester (Hytrel)

PC25 PC28PS

3E80 30CT 31BO 3360X2 37AL 3JET 3R80

THERMOPLASTIC

Liquid Petroleum Approved Hose

MPH

Type

Similar to 3130

Nylon

Polyurethane

High flexibility forklift twinline

Nylon

Polyester (Hytrel)

Non conductive SAE 100R7

Polyester

Polyurethane

Jetting hose based on 3130

Nylon

Polyurethane

General purpose SAE 100R8

Nylon

Polyurethane

3VEO

Non conductive jacking hose

Nylon

Polyurethane

STH

Stainless steel braid over Teflon速

Teflon速

Stainless steel

TECHNICAL DATA CHEMICAL RESISTANCE TABLE CAUTION The data in the following pages has been compiled from generally available sources and should not be relied upon without consulting and following the specific recommendations of the manufacturers of particular products The data is considered valid at 20°C (70°F) except where specified otherwise. Chemical compatibility can vary greatly with temperature A good rating does not necessarily indicate the suitability of a particular hose and chemical combination due to variables such as improper clamp and coupling application, special hose construction, gasket material etc. Nor does it imply compliance with relevant food standards or safety standards that may be applicable

SOLVENT INFORMATION Aromatic solvents: benzene, cumene, p-cumene, naphthalene, toluene, xylene, cresol, styrene, cyclohexane and combinations Aliphatic solvents: propane, butane, pentane, hexane, heptane, dipetene, tripropylene Halogenous solvents: chloroform, dichorobenzene, dichloroethylene, methylen bromide, methylen chloride, benzyl chloride, carbon tetrachloride, trichloroethylene, carbon disulphite, turpentine, perchloroethylene, dichloroethane Ketonic solvents: acetone, methyl ketone, isobutyl ketone, methyl ethyl ketone, methyl isobutyl ketone Esters solvents: butyl acetate, methyl acetate, anyl acetate, isobutyl acetate Amines: aniline, ethylene diamine , diethanol amine, triethanolamine, dimethyl amine, monoethanolamine Alcohols: methanol, ethanol, propanol, butanol, glycerol

Common Elastomers

ASTM Designation

Composition

General Properties

brominated butyl chlorinated butyl

BIIR CIIR

bromo isobutene-isoprene chloro isobutene-isoprene

excellent weathering resistance, low permeability to air and gases, good physical properties, resistant to heat poor resistance to petroleum based fluids, good resistance to fat

chlorinated polyethylene

CM (CPE)

chloro polyethylene

excellent ozone and weathering resistance, good oil and chemical resistance, excellent flame resistance

cross-linked polyethylene

XLPE UHMWPE

polyethylene and cross linking agent

excellent for a very wide range of solvents, chemicals, acids and oils

ethylene propylene

EPDM

ethylene propylene diene-terpolymer

excellent ozone, chemical and ageing resistance, poor resistance to petroleum based fluids, very good steam resistance

ethylene propylene

EPM (EPR)

ethylene propylene copolymer

excellent ozone, weathering, heat, chemical and aging resistance, poor resistance to petroleum products, very good steam resistance

hypalon ®

CSM

chloro-sulfonylpolyethylene

excellent weathering, ozone and acid resistance, good heat and abrasion resistance, fair resistance to petroleum based fluids

natural

isoprene natural

excellent physical properties, very good abrasion resistance, poor resistance to petroleum based fluids

neoprene

chloroprene

good weathering and flame retardant resistance, good oil reistance, good physical properties

nitrile (buna-n)

NBR

Acrylonitrile-butadiene

excellent petroleum products resistance, moderate resistance to aromatics, good physical properties

acrylonitrile-butadiene / polyvinyl-chloride

excellent petroleum products and weathering resistance, both for tube and cover

buna-n / PVC / NBR polyvinyl chloride polyacrylic

ACM

acrylic monomer

excellent oil and tar resistance at high temperatures

sbr

SBR

styrene butadiene

good physical properties, good abrasion resistance, poor resistance to petroleum based fluids

viton ®

FKM

fluorocarbon rubber

excellent high temperature resistance, particularly in air and oil, very good chemical resistance y

TECHNICAL DATA CHEMICAL RESISTANCE TABLE

{

U C U G C C

U G -

G G G G G U G U G G G U G C G G C U G G G -

C U U U

U G

C U C G C G U U U C U U U G U U C U C G C C U G -

C U G -

PVC

U U

G C U G U G G G C G U G G C C G G G G -

U U C U C C C U U U C U C G U -

Polyurethane

G C U G U C C C C G U G G C C G G G G -

U G G C C G G U G U G -

Polyester

C C U U U

G G U G U U G U G G G G G G C G G G G G G G G -

Barium Salts Barium Sulphate Barium Sulphide Basic Copper Arsenate Beer Beet Sugar Liquors Benzaldehyde Benzene (Benzol) Benzenesulphonic Acid Benzine Benzine (Petroleum Ether) Benzine (Petroleum Naphtha) Benzoic Acid Benzyl Alcohol Benzyl Benzoate Benzyl Chloride Biodiesel < 92c Biodiesel > 92c Bismuth Carbonate Black Sulphate Liquor Blast Furnace Gas Borac Acid Borax Bordeaux Mixture Boric Acid Boric Copper Sulphate Brake Oil, Dot 3 Brake Oil, Dot 4 Brake Oil, Dot 5 Brine Bromine Bunker Oil ButAdiene Butane Butter Oil Butyl Acetate Butyl Alchol (Butanol) Butyl Amine Butyl Carbitol Butyl Cellosolve Butyl Mercaptan Butyl Stearate Butylene (Butene) Butyraldehyde Butyric Acid Calcium Acetate 10% Aq Calcium Arsenate Calcium Bisulphate 10% Aq Calcium Bisulphide Calcium Bisulphite Calcium Carbonate Calcium Chlorate Calcium Chloride 10% Aq Calcium Hydroxide 10% Aq Calcium Hypochlorite 10% Aq Calcium Nitrate 10% Aq Calcium Salts Calcium Silicate Calcium Sulphate Calcium Sulphide

Nylon

C G G

U G U U U U -

Teflon

U U U U U C C

U G G G U

G C C U U U G

Class V

U C C U C

U G G C G U

G C C C U U G

Class IV

G U

U U U

G C C G U U G

Class III

C C C C C C C

G G G G G G G G G G G G G G G G G G G G G G G G G G G C G G G G G G G G G G G G G G G G G G G

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Class II

C C

AGENT

Class I

U C C C

PVC

Class V

Polyurethane

Class IV

U U U

Polyester

Class III

G G C C U C G G C G G U U C G -

Nylon

Class II

Acetaldehyde Acetic Acid, Glacial Acetic Acid, Less Than 10% Acetic Acid, Over 10% Acetic Anhydride Acetone Acetophenone Acetyl Acetone Acetyl Bromide Acetyl Chloride Acetylene Acrylonitrile Air (Under 20kgf/Cm2) Alcohols Aluminium Aluminium Acetate Aluminium Bromide Aluminium Chloride Aluminium Fluoride 20% Aluminium Hydroxide Aluminium Nitrate 10% Aqueous Aluminium Salts Aluminium Sulphate Aluminium Sulphate Alums Ammonia Gas, Cold Ammonia Gas, Hot Ammonia, Aq Ammonia, Liquid (Anhydrous) Ammonium Carbonate Ammonium Chloride Ammonium Hydroxide Ammonium Metaphosphate Ammonium Nitrate Ammonium Nitrite Ammonium Phosphate Ammonium Sulphate Ammonium Thiocyanate Amyl Acetate Amyl Alchol Amyl Chloride Amyl Chloronapthalene Amyl Napthalene Anethole Aniline Aniline Dyes Aniline Hydrochloride Animal Oils Antirnony Salts Apoclor Monsanto (Chlorinated Hydrocarbon) Aqua Regia Aromatic Hydrocarbons Arsenic Acid Arsenic Salts Askarel Asphalt <105 C Automatic Transmission Fluid (ATF) Barium Carbonate Barium Chloride Barium Hydroxide

Class I

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Teflon

AGENT

G G G G C C G G G G G G G G G G G G C C G G G G G G G G G G

G G G G G C G G G G G G U G G G G G G G G G -

G G G C U C G G G G U G C G G G G C C G -

G G U U G C C G G G C G U G G C G G G G -

G G G G G G G G G G G G G G G G

TECHNICAL DATA CHEMICAL RESISTANCE TABLE

G U G G G -

U U C C U U G U U -

G G C C U G

C C G

U G U U U U G G G G -

C U G U G G U -

PVC

C C C

Polyurethane

C G

Polyester

G G G G G G G G G G G G G G G G G G G G G G G G G G U G G G G G G G G G G G G

Decalin Denatured Alcohol Detergent / Water Solution (Conc) Diacetone Diacetone Alcohol Diammonium Phosphate Dibenzyl Ether Dibutyl Ether Dibutyl Phthalate Dibutyl Sebacate Dichlorobenzene Diesel Fuel Oils Diesel Oil Light Diethanolamine (20% Conc.) Diethyl Ether Diethyl Phthalate Diethyl Sebacate Diethylamine Diethylene Glycol Di-Isobutylene Di-Isopropyl Ketone Dimethyl Aniline Dimethyl Formamide Dimethyl Phthalate Dioctyl Phosphate Dioctyl Phthalate (Dop) Dioxane Dipentene Dowtherm A and E Enamels Essential Oils Ethanol Ethanolamine Ether Ethyl Acetate Ethyl Acetoacetate Ethyl Acrylate Ethyl Alchol (Ethanol) Ethyl Benzene Ethyl Cellulose Ethyl Chloride Ethyl Ether Ethyl Mercaptan Ethyl Pentochlorobenzene Ethyl Silicate Ethylene Cellulose Ethylene ChlorhydrIn Ethylene Chloride Ethylene Diamine Ethylene Dichloride Ethylene Glycol Ethylene Oxide Fatty Acid Ferric Chloride Ferric Chloride Ferric Nitrate Ferric Nitrate 10% Aq Ferric Sulphate 10% Aq Ferrous Chloride Ferrous Nitrate

Nylon

U U U G C G G G C G C U U C U C G U U C G G G G G G G G C C C G G U -

Teflon

G G G G G -

U C C G U C C C C C C U U G U U C U U U G G C G G G G G U U U G C G G -

Class V

G C C -

U C C G U C C C C C C U U G U U U U U U G G C G G G G G U U U C C G G -

Class IV

U U G U G

U G -

U G G G G G G G C G C G G G G U C U G U G G G G C G G G U U U G C G G -

Class III

U G U C U U U G U C U U U U U U C U U G G U U -

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Class II

G U C G G U U

AGENT

Class I

C U G U G U U G U C U U U U U U

PVC

Class V

Polyurethane

Class IV

G -

Polyester

Class III

G U C U C U U U U G G C C -

Nylon

Class II

Caliche Liquors (Chile Saltpetre) Cane Sugar Liquors Carbitol Carbolic Acid (Phenol) Carbon Bisulfide Carbon Dioxide Carbon Disulphide Carbon Monoxide Carbon Tetrachloride Carbonates Carbonic Acid Castor Oil Caustic Potash (<20%) Caustic Potash (>20%) Caustic Soda (Sodium Hydroxide) <20% Caustic Soda (Sodium Hydroxide) >20% Cellosolve Acetate Cellosolve Butyl Cellulubes Celanese (Phosphate Ester Base) Cellusolves Union Carbide China Wood Oil (Tung) Chlordane Chlorinated Solvents Chlorine Gas, Dry Chlorine Gas, Wet (<20%) Chlorine Trifluoride Chloroacetic Acid Chloroacetone Chlorobenzene Chlorobromomethane Chloroform Chloronapthalene Chlorosulphonic Acid Chlorotoluene Chromic Acid 30% Chromium Salts Cider Citric Acid Coal Gas Cod Liver Oil Coke Oven Gas Compressed Air (< 290 Psi or 2000 Kpa) Copper Chloride Copper Chloride 10% Aq Copper Cyanide 10% Aq Copper Sulphate 10% Aq Corn Oil Corn Syrup Cottonseed Oil Creosote Oil Cresol Cresylic Acid Crude Petroleum Oil Crude Wax Cupric Sulphate Cutting Oil White & Bagley No. 2190 Cyclohexane Cyclohexanol Cyclohexanone Cymene

Class I

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Teflon

AGENT

G G G G G G G G G G G G

G G G G G G G G G G G G G G G G U G G G G C G -

C C C G C C C C G G C C C C U U U G C G G -

C U C G C C C C G G C C C C U U U C C G G -

U G C C U U G G C C U C U U U G G G G -

G G G G G U G G U G G G G G G G G G G G G G G G G G G G G G G G G G G G

}

TECHNICAL DATA CHEMICAL RESISTANCE TABLE

Polyurethane

PVC

G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G

Polyester

G G G G G

Hydrogen Peroxide, Dilute Hydrogen Sulphate, Gaseous Hydrogen Sulphide, Dry Hydrogen Sulphide, Wet Hydrogluosilic Acid Hydrolube Union Carbide (Hydraulic Fluid Water Glycol Base) Irus Shell 902 Hydraulic Fluid (Water-Oil Emulsion) Iso Octane Isobutyl Alcohol IsocyanAtes Isopropyl Acetate Isopropyl Alcohol Isopropyl Ether Jp-4, Jp-5 Kerosene Ketones Lacquer Lacquer Solvents Lactic Acid Lard Lead Acetate Lead Arsenate Lead Sulphate Lead Tetramethyl Light Oil Lime Lime Sulphur Linoleic Acid Linseed Cake Linseed Oil Linseed Oil Liquefied Petroleum Gas (LPG) Lubricating Oils, Diester Base Lubricating Oils, Petro Base Magnesium Chloride 10%Aq Magnesium Hydroxide 10%Aq Magnesium Sulphate 10%Aq Maleic Acid Mercuric Chloride Mercury Mesityl Oxide Methane Methy Salicylate Methyl Acetate Methyl Alcohol (Methanol) Methyl Bromide Methyl Chloride Methyl Ethyl Ketone (MEK) Methyl Formate Methyl Isopropyl Ketone Methyl Methacrylate Methyl Sulphate Methylene Chloride Methylisobutylketone (MIBK) MIL-H-46170 MIL-H-5606 MIL-H-6083 MIL-H-83282

Nylon

U C C

C C C G C C G C C G G G C C C G G G G G G C C C U U U G G G G C G C

Teflon

G C U G G G G U G G G G U U U U G G C

C G G G G G

U U U C U C G G G G C G G G G G G G G G C G G G C G C G G C U G U

Class V

U C U

G U C C G G U

U U C U C G G G G C G C G G G G G G G G G G G G C G C C G U U G U

Class IV

C C G G -

U G U G G G G G G G G G G G G G G G G G G G G G G G G G G U U G U

Class III

G U U U G U G -

C C U G G G G C U G G U G U G C G C U U C

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Class II

U G

AGENT

Class I

U C

PVC

Class V

Polyurethane

Class IV

U U U C -

Polyester

Class III

C G C C C C C G G

Nylon

Class II

Ferrous Salt Solutions Ferrous Sulphate Fluoboric Acid Fluoboric Acid Fluorine Fluorosilicic Formaldehyde Formic Acid Freon 12 (Refrigerant) Freon 13 (Refrigerant) Freon 22 (Refrigerant) Fruit Juices Fuel Oil Fuel Oil (Aromatic Gas) 100 Octane Fuel Oil (Aromatic Gas) 100 Octane Fumaric Acid Furan Furfuran Furfural Furfuryl Alcohol Galic Acid (< 20%) Gas (Natural) Gas Oil Gaseous Hydrogen Gasohol Gasoline Gasoline (Aromatic) Gasoline (Nor-Aromatic) Gelatine Glucose Glue (Depends On Type) Glycerine, Glycerol Glycol To Wc Grease,Petroleum Green Sulphate Liquor Heavy Water (D20) Helium Heptane Hexaldehyde Hexane Hexene Hexyl Alcohol Hydraulic Oil Phos. Ester Blend (MIL L-7808) Hydraulic Oil, Auto Transmission Fluid Hydraulic Oil, Chlorine Base Hydraulic Oil, Ester Blend Hydraulic Oil, Ordinary Petro Hydraulic Oil, Phosphate Ester (FR) Hydraulic Oil, Silicone Oil Hydraulic Oil, Sodium Silicate Base Hydraulic Oil, Water & Petrol Emulsion (FR) Hydraulic Oil, Water Glycol (85c) Hydraulic,Oil, Water & Oil Emulsion Hydrobromic Acid Hydrochloric Acid V% Hydrocyanic Acid Hydrofluoric Acid, Cold Hydrofluoric Acid, Hot Hydrofluorsilic Acid Hydrogen (Gaseous) Hydrogen Peroxide, Concentrated

Class I

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Teflon

AGENT

C G -

U U U U

C U -

G -

G G G G -

G C -

G -

G G -

G U C G G G G G G G -

C U U U -

G G C G -

G G G G G G G G G G G G G

G G G G G G G G G G G G G G G G G G G G G G G G C G G G G -

G C G C C G G G G G G G G C G C G C G G G C C U U C G C -

U C U U G G G G G G G G G G G G C G U U U U U U U -

G G G U C G C G C U -

U U G C G G U U U G U G G G G G G G U U U C G G G G

G G U U -

G G G G G G G G G G G G G G G G G G -

Â&#x20AC;

TECHNICAL DATA CHEMICAL RESISTANCE TABLE

G G G G G G G G G G G G G G G G G G G G G G

G -

G U U C U G G G G G G C G G G G G C G G G G

G U

U G U U C G C U U U U U

C G U G G U U U U U

G C G G G C G U U U U

PVC

G G -

G U G U U U U U U U U -

Polyurethane

G G G G G G G G G G G -

G U C G G C G G C G G G U

Polyester

G G G

Potassium Permanganate (5%. Conc.) Potassium Sulphate Propane Propyl Acetate Propyl Alcohol Pydraul (Stauffer) F-9,150, 600, 625 Pyrethrum Pyridine Red Oil Salt Water (Sea Water) Saturated Steam Sewage Silicone Oils Silver Nitrate Skydrol Monsanto 500, 7000 Soap Solutions Soda (Sodium Carbonate) Soda Water Sodium Acetate 10% Aq Sodium Bicarbonate 10% Aq Sodium Bisulfite Sodium Bisulphate Sodium Borate Sodium Carbonate Sodium Chloride Solutions Sodium Cyanide Sodium Hydroxide <10% Sodium Hydroxide 40% Sodium Hypochloride 10% Sodium Hypochlorite Sodium Metaphosphate 10% Aq Sodium Nitrate 10% Aq Sodium Perborate 10% Aq Sodium Peroxide 10% Aq Sodium Phosphates 10% Aq Sodium Silicate 10% Aq Sodium Sulphate 10% Aq Sodium Sulphide Sodium Sulphite 10% Aq Sodium Thiosulphate (Hypo) 10% Aq Solution 2-4D DDT Preparation Hydroxy Quinoline Soybean Oil Stannic Chloride Stannous Chloride Steam Steam Stearic Acid Stearic Acid, Botanical Stearin Stoddard Solvent Styrene Sucrose Solution Sulphur Sulphur Sulphur Chloride Sulphur Dioxide Sulphur Trioxide Sulphuric Acid, 10%, Hot Sulphuric Acid, 10%. Cold Sulphuric Acid, 75%, Cold

Nylon

G G G U U U G G G U G C G C G G C C G C C C G G C C G G G C G

Teflon

G G G G C C G U C U G G G G C C G G C G G U U G C U G U U G U G

Class V

U U U U G -

G G G G C C U G U C U G G G G C C G G C G G U U G C U C U U G U G

Class IV

U U C U G U -

G G G G G G U G C C G G G G G G G G G G G G U G G G U C G C G C G

Class III

U U U U

G G

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Class II

G U G G U U U U U U U -

AGENT

Class I

G G G G U G U G G G U U U G U U C U C U G U U U U U U G G G G G -

PVC

Class V

Polyurethane

Class IV

U C G U U U U U U U C U

Polyester

Class III

G C G U C G G G G -

Nylon

Class II

Milk Mil-L-2104 Mil-L-23699 Mil-L-7808 Mineral Oils Molasses Monochlorobenzene Mustard Naphtalene Naphtha Napthenic Acid Natural Gas Nickel Acetate 10% Aq Nickel Chloride Nickel Sulphate Nicotine Nitric Acid (Conc) Nitric ACid (Dil) Nitriuc Acid (Red, Fuming) Nitrobenzene Nitrogen / Argon Gaseous Nitrous Oxide Octyl Alcohol Oil Oil Of Turpentine Oleic Acid Oleum Spirits Olive Oil Ortho-Dichlorobenzene OS 45 Monsanto Hyd. Fluid (Silicate Ester Base) Oxalic Acid Oxygen (Liquid) Oxygen Gaseous Ozone Paint (Oil Based) Paint Solvents (Oil Base) Palmlitic Acid Peanut Oil Pentane Perchloric Acid Perchloroethylene Petroleum Oils (Refined) Petroleum Oils (Sour) Phenol (Carbolic Acid) Phenolates Phenols (Carbolic Acid) Phosphate Ester Base Oil Phosphoric Acid (70%) Phosphoric Acid 10% Picric Acid (Molten) Picric Acid (Solution) Pine Oil Pinene Plating Solution, Chrome Potassium Acetate 10% Aq Potassium Chloride Potassium Cyanide Potassium Dichromate Potassium Hydroxide (Potash) Potassium Nitrate

Class I

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Teflon

AGENT

G G G G G G G

U G G G G C G G G G G G G G G G G C G G G G G G G C U G G G G G U C C -

U G G C G C G U G G G G G G G G C C G G G G G G G U G G U C G U U U -

U G G C G G G U G G G G G G G G C C G G G G G G G U C G U C G U U U -

G G G U G U G U G G C G G G G G G G G G G G G G G G U G C G C G G -

G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G

TECHNICAL DATA CHEMICAL RESISTANCE TABLE

G G U -

PVC

G C G G U G G

Polyurethane

G G -

U U -

Polyester

G C C C

U U U G G G G U U U -

Nylon

U U U U U G U

Class V

U U U

Class IV

U G -

Class III

U U U G G U G U -

Class II

Sulphuric Acid, 75%, Hot Sulphuric Acid, 95%, Cold Sulphuric Acid, 95%, Hot Sulphurous Acid Tannic Acid Tar Tartaric Acid Terpineol Toluene Toluol Transformer Oil Transmission Fluid Type A Tributoxyethyl Phosphate Tributyl Phosphate Trichloracetic Acid Trichlorethylene Tricresyl Phosphate Trisodium Phosphate Solution Tung Oil (China Wood Oil) Turpentine Oil Ucon Union Carbide (Hydraulic Fluid Water Glycol Base) Urea Uric Acid Varnish Vegetable Greases Versilube Vinegar Vinyl Chloride Water @ 65°C Water Glycol Water, Normal Temp Whiskey White & Bagley No. 2190 Cutting Oil Wine Wool Oil Xylene Xylol Zinc Acetate Zinc Chloride 10% Aq Zinc Hydrate Zinc Sulphate 10% Aq

Class I

Legend: G = Good C = Conditional U = Unsatisfactory No Data

THERMOPLASTIC

RUBBER

Teflon

AGENT

G G G

G G G G G G G

U U G G G G G G U G G G G

U U C G G C C C U U C C G

U C G G G U U U C C U G G

G G G G G G G G G G G G G G

G G G G G G G G G G G G U U

C C U G C G G G C C G C C

G C U G C G G G C C G C C

G G G U G G G G U U G G G

G G G G G

Page/s

Description

Page/s

3130

Description

High Pressure Non Conductive

Ordering Assemblies

3800

High Pressure R8

PC25

3E80

High Pressure Thermoplastic

PC28PS

1 - Wire Braid

High Temp 2 Wire

PC35

2 - Wire Braid

High Temp R5

PC42

2SC

HTAB / HTFH

R1AT

30CT

IRFAW

R1ATFS

30CTX2

IRFWSDH

R2AT

3360X2

IROFSD

R2ATHT

37AL

Isobaric Hoses

22 - 30

R5HT

37ALX2

Jacking Hose

21, 47

R4HT

3R80

JBF

R8 hose

14 - 16

R12C Spiral Hose

R13C Spiral Hose

Description

3VEO

Jet Wash

Broad Spectrum Hose

JH70

C21

JW210A

Safety Warning

C25

JW250 / 250A

Selection Guide

2-3

C35

JW400 / 400A

Stainless Teflon Hose

C42

Large Bore Hose

STH

C45

Low Pressure High Temp

Thermoplastic Hoses

Compact R8

Low Pressure Oil Hose

Truck Hose

Fast Find Table

MPH

Twinline 30CT

Fire Suppression Hose

Multi Purpose Hose

Twinline Non Conductive

Forklift Twinline

Non Conductive Hose

Waterblast Hoses

FRAS Air Water Hose

Non Conductive Jacking

FRAS Air Water Suction

Oil Suction Hose

37 - 48

43 35 - 36

WB1000

6-7

WB1100

Chemical Compatibility Tables Commence page 50

Page/s