Section B - Hydraulic Hose by PIRTEK

SAFETY PRECAUTIONS FOR THE USE OF PIRTEK® HOSE ASSEMBLIES Your Personal Safety may directly or indirectly be compromised if the hose assembly is abused. By following the INSTRUCTIONS below, the more common abuses of hose and hose assemblies can be avoided.

HYDRAULIC HOSES

WARNING

INSPECT the hose assembly before each use.

SAFETY WARNING

REPLACE the hose assembly immediately if: A. The cover appears abnormal B. You believe it may be abnormal C. There is any fluid leakage D. The fittings are damaged E. The hose is damaged F. Reinforcement is visible through the cover DO NOT EXCEED the maximum working pressure of the hose. DO NOT KINK the hose assembly. DO NOT BEND beyond the specified minimum bend radius of the hose. DO NOT EXPOSE to temperatures beyond the published maximums for the hose or fluid being conveyed. DO NOT USE AS A STRENGTH MEMBER for pulling or lifting equipment. Use support cables for vertical installations. USE ONLY WITH COMPATIBLE FLUIDS as outlined in the Chemical Compatibility Charts or as specifically approved in writing by Pirtek Fluid Systems. PIN PRICK THE COVER of hoses used for compressed air above 17 bar or 250 psi to allow the safe escape of air that permeates through the liner and reinforcement (except STH, R5HT and 3130). The maximum working pressure and temperature must also be reduced by 30%. Use only Pirtek HOSE AND FITTINGS COMBINATIONS as designated in their current assembly guidelines. Use only Pirtek PROCEDURES and ASSEMBLY EQUIPMENT as published and maintained in their M.A.P.S. documentation. Relationship between actual working presasure and service life Experimental pressure waveform

90 Pressure as a % of Rated Pressure at 100

Peak pressure 150 ± 7% Pressure rising rate

80 70 % of Service Life

• The use of conventional wire reinforced rubber hose often entails the pressure fluctuations of fluid. • The factors concerned with such pressure fluctuations are generally classified into two: those stemming from the pump itself, and the others ascribable to external impacts imparted to the hose via the operating demands. The latter are considered to have the greater effect on the service life of the hose. • External impulse pressure is estimated to be 150% of the set pressure (actual working pressure) of a relief valve, and sometimes exceeds 300%.

100

125

Rated pressure

100 75 50

25 (kgf/cm ) 0

5% of one cycle

150

15% of one cycle 1/35 minute a cycle

30 20 10 0

100 125 150

200 300 400 Actual working pressure Recommended working pressure

500

600

This page is part of a complete catalogue containing technical and safety data. All data must be reviewed when selecting a product. Pirtek reserve the right to change technical specifications without notice Rev 4

SELECTION GUIDE Page Group

Normal Usage sage

Features & Bene Benefits

(See main Specifications page for details and Approvals)

IRFWSDH FRAS Suction/Delivery

Hardwall FRAS hose for arduous air / water applications in u/ground coal mining

Electrically conductive NBR liner and CR cover meeting AS2660 requirements

MPH Multipurpose

High quality black multi-purpose hose with spiral wound textile reinforcement

Synthetic black rubber inner and outer. Abrasion and weather resistant. Oil resistant

IRFAW FRAS Air / Water

Softwall hose for arduous air/water applications in underground mining

Weather resistant black cover with orange spiral. Fire resistant / anti static rating

R6 Textile braid hose

Low pressure hydraulic fluids, aqueous emulsions, air transfer and water

SAE 100R6 rated hose with oil resistant liner suited to push fit fittings

R5HT Hi-Temp. Truck Hose

Medium pressure air and hydraulic hose common on American equipment

Internal diameters match the inside diameter of copper tube to yield an unrestricted flow

HTAB/HTFH Engine & Air Brake

Specifically intended for trucking industry applications involving diesel fuel / air brakes

Black rubber with poyester textile outer cover for safe escape of entrapped air

12-14

JW210A / JW250 / JW400 Jet Wash Hose

Flexible high pressure compact hose for pressure cleaning with water and detergents

210 and 250 bar versions with 1-wire braid, 400 bar version with 2-wire braid

15-16

R1AT / R1ATFS One wire braid

Medium pressure hose for hydraulic fluids and aqueous emulsions and water

Normally black but R1ATFS has red cover to indicate use in fire suppression systems

17-19

R2AT/2SC, JH70 Two wire braid

High pressure hose for hydraulic fluids and aqueous emulsions and water. JH70 for high pressure jacking applications

Synthetic rubber oil resistant liner and abrasion resistant cover. 2 steel braids

R2ATHT High Temp. 2 wire hose

High pressure hose for hydraulic fluids and aqueous emulsions and water

As above but high temperature rubber formulation. Blue cover

HYDRAULIC

SELECTION GUIDE

Tank truck suction & delivery hose for fuels & Synthetic smooth oil resistant inner tube. 2 mineral oils with aromatic content ≤ 40% braids of textile & a metal spiral. Antistatic

C21 Isobaric 210 bar

21, 25

C25, PC25 Isobaric 250 bar

PC28PS Isobaric 280 bar

23, 26

C35, PC35 Isobaric 350 bar

24, 27

C42, PC42 Isobaric 420 bar

C45 Isobaric 450 bar

JBF Large Bore Hose

Large bore medium pressure hose for hydraulic fluids incl. aqueous emulsions

Spiral construction. Prolonged usage with water based fluids will corrode reinforcement

LPG LP Gas Hose

High pressure hose for transfer of LPG,

Woven black poly cover with blue trace over single st. steel braid / teflon liner. AGA approved.

R12C 4000-2500 psi Spiral

R13C 5000psi Spiral

High pressure multi-spiral hose for hydraulic fluids such as glycol, mineral oils, fuels, hydrocarbons etc. Provide flexibility and high temperature resistance

WB1000 Water Blast Hose

Construction

IROFSD Oil Fuel Suction

Product Code

MISC.

HYDRAULIC HOSES

RUBBER HOSES

WB1100 Water Blast Hose

Class 21 hoses suit 210 bar WP Isobaric (constant working pressure for all sizes) range of hoses exclusive to Pirtek. Simplifies hose selection in circuits of known working pressure ‘PS’ Suffix denotes extreme abrasion resistant sheath over the cover ‘PC’ Prefix denotes Komatsu® genuine hoses

Class 25 hoses suit 250 bar WP Class 28 hoses suit 275 bar WP Class 35 hoses suit 350 bar WP Class 42 hoses suit 420 bar WP Class 45 hoses suit 450 bar WP

butane-propane on stationary and mobile eqpm’t.

Very high constant pressure hose for water scaling systems. Suitable for passage of water and aqueous solutions

Compatible with Caterpillar® reusable fittings

2.5 : 1 safety factor. Do not use in hydraulic systems

SELECTION GUIDE Page Group

Product Code

Construction

Normal Usagee

Features & Ben Benefits

(See main Specifications page for details and Approvals)

Flexible in cold temperatures (coldrooms). Small OD and good over sheaves

Constant 207 bar working pressure for all sizes. Perforated cover for gaseous applications

3JET Water jetting hose

Medium pressure hose for water jetting and drain cleaning. Low elongation

Constant 207 bar working pressure for all sizes. Perforated cover for gaseous applications

30CTX2 Twin cold temp. hose

Commonly found in forklift applications in cold rooms

Constant 207 bar working pressure for all sizes. Hytrel core tube and perforated cover

3130 General purpose R7

General hydraulics, material handling, pneumatics, and agricultural equipment

The original SAE 100R7 design with nylon tube and urethane cover. Economical

3360X2 Twin forklift hose

Similar to 30CT except with nylon core tube

As for 30CT but with nylon tube and a wider range of sizes

37AL R7 non-conductive

Non conductive hydraulic hose for aerial lift equipment

Polyester core and good cold weather flexibility. SAE 100R7 performance

37ALX2 Twinline non-conductive

Non conductive twin line hydraulic hose for aerial lift equipment

Polyester core and good cold weather flexibility. SAE 100R7 performance

3800 Compact R8

Pilot lines, general hydraulics, and machine tools at higher pressures than 100R7

Compact dimensions due to aramid fibre reinforcement - suits 100R7 fittings

3E80 Non-conductive R8

Non conductive hydraulic hose for aerial lift equipment with higher working pressures

Dimensionally as for 3R80 hose. Nylon core and orange urethane cover

3R80 General purpose R8

General hydraulics, material handling, forestry and construction

The original 100R8 with nylon core and urethane cover. Long impulse / flex life

3VE0 High Pressure Jacking

Extreme pressure hose for high pressure jacks and rescue equipment

Orange cover signifies electrically non conductive hose

STH St. Steel TeflonÂŽ hose

Laundry equipment, plastic moulding presses, steam and hot air discharge

Teflon liner and SS braid allow high temperature and chemical capability

40 41 42

THERMOPLASTIC

30CT Cold temp. hose

SELECTION GUIDE

HYDRAULIC HOSES

THERMOPLASTIC HOSES

ORDERING PIRTEK ASSEMBLIES Should you wish to describe a Pirtek hose assembly in an abbreviated form, please use the following format. A forward slash is used to separate each field. Product Codes for fittings can be found in Pirtek Catalogue Section C (except Mining Fittings Section U)

If spiral guard SSG-025 were fitted over the full length, the designation would be: R1AT-12 / JF1-1712J / C614-1212J / 1200 / SSG-025 If both ends were fitted with the 45Â° flanged elbow set in alignment, the designation would appear: R1AT-12 / C614-1212J / 1200 / 0 Generic Pattern : Hose / End A / End B / Length / Protection / Angle This page is part of a complete catalogue containing technical and safety data. All data must be reviewed when selecting a product. Pirtek reserve the right to change technical specifications without notice Rev 4

HYDRAULIC HOSES

FAST FIND TABLE

SIZE, PRESSURE, TEMPERATURE

Product Code & Hose Type dia. (ins.) mm size

Working Pressure (bar)

Temp.

⅛

³/₁₆

⁵/₁₆

⅜

/₈

1¼

1½

1¾

2½

3½

-003

-004

-006

-008

-010

-013

-016

-019

-025

-032

-038

-045

-050

-063

-076

-090

-100

-125

IROFSD

Oil Fuel Suction

IRFWSDH

FRAS Air/Water Suction

MPH

Multipurpose

IRFAW

FRAS Air / Water

Low pressure hydraulic

R5HT

High Temp 100R5

20 35

35 28

°C -20°/+100°

-15°/+70°

-40°/+100°

-15°/+70°

-40°/+150°

9 10

FAST FIND TABLE

Unique diameters throughout range 3/16” to 1.13/16”

-40°/+135°

HTAB/HTFH Engine/Air Brake Hose

Unique diameters throughout range 3/16” to 1.3/8”

-40°/+149°

JW210A

Jet Wash 210 bar

210

-40°/+155°

JW250 / A

Jet Wash 250 bar

250

-40°/+155°

JW400 / A

Jet Wash 400 bar

400

-40°/+155°

R1AT

1-Wire Hydraulic

-40°/+100°

R1ATFS

Fire Suppression

-40°/+100°

R2AT/2SC

2-Wire Hydraulic

-40°/+100°

R2ATHT

2-Wire High Temp.

-40°/+100°

JH70

Jacking Hose

-40°/+100°

C21

Isobaric 210 bar

C25, PC25

Isobaric 250 bar

PC28PS

Isobaric 280 bar

C35, PC35

Isobaric 350 bar

C42, PC42

Isobaric 420 bar

C45

Isobaric 450 bar

JBF

Large Bore

LPG

LPG Gas Hose

R12C

4000-2500 psi Spiral

R13C

250

225

215

180

160

180

160

330

275

250

215

165

125

80 69/70 70

396

345

293

224

207

172

155

120

103

700

225 415

400

350

140

105

210 250

250 280

280

350

350 420

280 380 420

350

420

250

-40°/+120°

350

-40°/+120°

23,26

420

-40°/+120°

24,27

-40°/+100°

-20°/+125°

26 276

276

21,25

250

140 276

-40°/+120°

250

450 26

-40°/+120°

276

207

172

-40°/+121°

5000 psi Spiral

345

-40°/+120°

WB1000

1000 bar Water Blast

1000

-40°/+80°

WB1100

1100 bar Water Blast

-40°/+80°

30CT

Cold Temp Isobaric 207

-54°/+94°

3JET

Water Jetting Hose

-40°/+66°

30CTX2

Twin Line 30CT

-54°/+94°

3130

Medium Pressure

-40°/+100°

3360X2

Twin Line Forklift

-54°/+94°

37AL

Non-conductive

37ALX2

Twin Line 37AL

3800

High Pressure compact

3E80

HP Non-conductive

3R80

High Pressure

3VEO

High Pressure Jacking

STH

St Steel Teflon Hose

1100 207 331 172

207

331 207

207

172

155

138

207 86

207 207 345 345 206

207

-54°/+100°

207

-54°/+100°

345

276

241

-40°/+100°

345

276

241

-40°/+100°

345

276

241

-40°/+100°

689

551

-40°/+66°

-55°/+240°

206

172

138

120

155 103

138 69

Chemical Compatibility Tables Commence page 48

Pg.

HYDRAULIC HOSES

IROFSD

OIL / FUEL SUCTION & DELIVERY

Construction

Applications

Inner Tube:

Light weight hardwall suction and delivery hose

Black smooth NBR compound

for fuels having an aromatic content up to 30%, and mineral oils. Suitable in hydraulic systems and for loading and unloading of tank trucks, refineries and maintenance shops

Reinforcement:

Temperature Range:

Limitations:

High strength synthetic cord plus embedded

-20째C up to +100째C

Not suitable for ester oils

Cover:

Comment:

Hose Tails:

Black, smooth (wrapped finish) SBR weather

Lay line example may not be a true indication

Pirtek J, 932, 934, 954 Series crimp fittings

resistant rubber compound

of current status. Refer Pirtek for current

L Series, Cam & Groove, Combination Steel

information

(all with clamps)

steel helix wire and anti-static copper wire

RUBBER HOSE

Lay line example: Black text on yellow background. Note Comment above

PIRTEK OIL FUEL S/D IROFSD 10 BAR (150psi) WORK.PRESS.

Nominal ID

Product Code

Pressure bar

Min bend radius

Weight

Crimp Tail Series

ins

working

min burst

vacuum

Kg/m

IROFSD-019

3/4

0.9

0.67

IROFSD-025

0.9

105

0.80

IROFSD-032

1.1/4

0.9

135

0.98

IROFSD-038

1.1/2

49.5

0.9

165

1.34

932

IROFSD-045

1.3/4

0.9

180

1.60

IROFSD-051

0.9

230

1.84

J, 932

IROFSD-063

2.1/2

0.9

300

2.79

J, 954

IROFSD-076

0.9

360

2.94

934

IROFSD-102

102

118

0.9

500

4.94

IROFSD-125

125

145

0.9

620

7.50

HYDRAULIC HOSES

IRFWSDH

FRAS AIR / WATER SUCTION & DELIVERY

Construction

Applications

Reference Speifications

Inner Tube:

Hardwall hose designed for arduous air / water

Approvals:

Black, smooth, electrically conductive NBR

applications in underground coal mining, where

Meets or exceeds

rubber compound

fire resistant, anti static properties are required

AS2660, incorporating AS1180.13A and AS1180.10B

Reinforcement:

Temperature Range:

High strength synthetic cord plus helix wire

-15°C up to +70°C

Cover:

Comment:

Hose Tails:

RUBBER HOSE

Black smooth (wrapped finish) electrically

Lay line example may not be a true indication

Industrial fittings

conductive CR rubber compound, fire, oil

of current status. Refer Pirtek for current

High pressure 2 or 4 bolt clamps

weathering and UV resistant

information

Pirtek “J” series 2

Lay line example: White text on orange background. Note Comment above

PIRTEK FRAS WATER SUCTION & DELIVERY IRFWSDH 20BAR (290PSI) W.P MEETS & EXCEEDS AS2660 CLASS B

Nominal ID

Product Code

Pressure bar

Min bend radius

Weight

IRFWSDH-025†

DN 25

mm 25.4

ins 1

mm 42.5

working 20

min burst 80

vacuum 0.9

mm 125

kg/m 1.34

IRFWSDH-051

50.8

0.9

255

2.58

IRFWSDH-063†

63.5

2.1/2

0.9

320

3.27

IRFWSDH-076

0.9

375

3.96

IRFWSDH-102

100

102

124

0.9

610

5.71

IRFWSDH-152†

150

152

178

0.9

1000

11.46

† Subject to availability

HYDRAULIC HOSES

MPH

MULTIPURPOSE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Low pressure hose for fluids such as mineral

Exceeds SAE J 517 (100 R6)

Seamless synthetic rubber, oil resistant

and vegetable oils, aqueous emulsions, water,

Exceeds EN 854 R6

air and inert gases.

JIS B 8360

Reinforcement:

Temperature Range:

Impulse Testing:

Two or four spirals of textile fibre

Water 0º C to +50º C (continuous)

400 000 cycles of JIS waveform @ 133% of

Water 0º C to +70º C (temporary)

working pressure (hose only) all sizes

Air -40º C to +50º C (in case of air applications, pressure should be less than 15bar) -40°C up to 70°C external ambient Cover:

Comment:

Hose Tails:

Black synthetic rubber resistant to abrasion,

Lay line example may not be a true indication

Pirtek ‘P’ Series all sizes

oils, ozone and weathering

of current status. Refer Pirtek for current

Pirtek ‘T’ Series option on 3/8, 1/2, 5/8 sizes

information Lay line example: Green text on black background. Note Comment above

RUBBER HOSE

Other fluid -40°C up to +100°C

PIRTEK MULTI MPH-12 (3/4”) 35BAR W.P. (500 PSI)

Product Code

Nominal ID

Reinforcement

4 fabric spiral

mm 14.0

working 35

Min bend radius

Weight

min burst 140

mm 55

Kg/m 0.15

Pressure bar

MPH-04

mm 6.3

in 1/4

MPH-05

8.0

5/16

4 fabric spiral

15.8

140

0.19

MPH-06

9.5

3/8

4 fabric spiral

17.4

140

0.21

MPH-08

12.7

1/2

4 fabric spiral

21.3

140

0.28

MPH-10

15.9

5/8

2 fabric spiral

23.5

140

110

0.30

MPH-12

19.0

3/4

4 fabric spiral

31.4

140

135

0.59

MPH-16

25.4

4 fabric spiral

37.5

140

170

0.74

HYDRAULIC HOSES

IRFAW

FRAS AIR / WATER / STONEDUST

Construction

Applications

Inner Tube:

Softwall hose designed for arduous air / water

Black smooth electrically conductive NBR oil

applications in underground coal mining, where

resistant rubber compound

fire resistant anti static properties are required

Reinforcement:

Temperature Range:

Approvals:

2 or 4 spiral plies of high strength synthetic cord

-15°C up to +70°C

Meets or exceeds AS2660-91B, incorporating AS1180.13A and AS1180.10B

Cover:

Comment:

Hose Tails:

RUBBER HOSE

Black smooth (wrapped finish) electrically

Lay line example may not be a true indication

Industrial fittings / FFI Ferrules

conductive CR rubber compound with orange

of current status. Refer Pirtek for current

High pressure 2 or 4 bolt clamps

spiral stripe. Fire, oil and weather resistant

information

Lay line example: Black text on orange background. Note Comment above PIRTEK AIR / WATER / STONEDUST FRAS IRFAW 20 BAR (290 psi) WORK. PRESS. MEETS & EXCEEDS AS 2660 “CLASS B”

Product Code

Nominal ID

Reinforcement

Pressure bar

Weight

working

min burst

Kg/m

IRFAW-013

1/2

2 spiral plies

0.36

IRFAW-019

3/4

2 spiral plies

0.47

IRFAW-025

2 spiral plies

0.70

IRFAW-032

1.1/4

2 spiral plies

1.02

IRFAW-038

1.1/2

2 spiral plies

52.5

1.21

IRFAW-051

2 spiral plies

1.60

IRFAW-063

63.5

2.1/2

4 spiral plies

2.27

IRFAW-076

4 spiral plies

2.53

IRFAW-102

102

4 spiral plies

120

3.60

HYDRAULIC HOSES

LOW PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, oil

Low pressure hose for hydraulic fluids such as

SAE J 517 (100 R6)

resistant

mineral and vegetable oils, aqueous emulsions,

EN 854 R6

water, air and inert gases Reinforcement:

Temperature Range:

One braid of textile fibre

-40°C up to +100°C (125° intermittent)

Cover:

Comment:

Black synthetic rubber resistant to abrasion, oils,

This hose is not stocked by Pirtek, but is included Pirtek ‘P’ Series all sizes

ozone and weathering

as a technical reference for what is a commonly

Hose Tails:

specified Standard. It can be supplied to special

RUBBER HOSE

order

Lay line example: Note Comment above

Product Code

Nominal ID

R6-03 †

mm 5.0

R6-04 † R6-05 †

Pressure bar

Min bend radius

Weight

in 3/16

mm 10.9

working 34

min burst 138

mm 50

Kg/m 0.1

6.5

1/4

12.6

112

0.13

8.0

5/16

14.3

112

0.15

R6-06 †

9.5

3/8

15.8

112

0.18

R6-08 †

1/2

19.8

112

100

0.23

R6-10 †

5/8

23.0

125

0.28

R6-12 †

3/4

26.5

150

0.36

R6-16 †

32.5

165

0.45

† Subject to availability

HYDRAULIC HOSES

R5HT

LOW PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, oil

Low to medium pressures hose that will handle

Exceeds SAE J 517 (100 R5)

resistant

high temperature hydraulic fluids such as mineral and vegetable oils, aqueous emulsions, water, air and inert gases

Reinforcement:

Temperature Range:

One textile braid and one braid of high tensile

-49°C up to +150°C,

steel wire

except air (not to exceed 121°C) and

Impulse Testing: See Table below for Impulse Test criteria (hose only)

water (not to exceed 82°C)

RUBBER HOSE

Cover:

Comment:

Hose Tails:

Black synthetic rubber with blue polyester textile

Lay line example may not be a true indication

Pirtek ‘A’ Series (field attachable)

outer braid resistant to abrasion, oils, ozone and

of current status. Refer Pirtek for current

Pirtek ‘R’ Series (crimp)

weathering. Permeable cover allows safe escape information of entrapped air when used to conduct high pressure air

Lay line example: White ink-jet text on blue background. Note Comment above PIRTEK HI-TEMP 8.3MM (5/16”) R5HT-06 155 BAR (2,250PSI) WORK. PRESS: 150°C./SAE J1402 TYPE AII 2Q04 BATCH 0037

Product Code

Nominal ID

Pressure bar

Min bend radius

Weight

Test Impulses

R5HT-04

mm 5.1

in 3/16

mm 13.2

working 207

min burst 827

mm 76

Kg/m 0.19

150 000

R5HT-05

6.8

1/4

14.8

207

827

0.24

150 000

R5HT-06

8.3

5/16

17.1

155

620

102

0.34

150 000

R5HT-08

10.7

13/32

19.5

138

552

117

0.39

150 000

R5HT-10

13.2

1/2

23.4

121

483

140

0.55

150 000

R5HT-12

16.4

5/8

27.4

103

414

165

0.69

150 000

R5HT-16

22.8

7/8

31.4

221

187

0.66

150 000

R5HT-20

29.2

1.1/8

38.1

172

229

0.78

100 000

R5HT-24

35.5

1.3/8

44.4

138

267

1.00

100 000

R5HT-32 †

46.6

1.13/16

56.2

20.7

337

1.40

100 000

† Does not comply with SAE 100R5 operating pressure of 24 bar or minimum burst pressure of 96 bar

ENGINE & AIR BRAKE* HOSE EXTRA FLEXIBLE LOW PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, oil

Low to medium pressures hose that will handle

* SAE J1402 Type AII in sizes -04 through -12

resistant

high temperature hydraulic fluids such as mineral FMVSS106 and vegetable oils, aqueous emulsions, gasoline, Consult Pirtek for specific Industry Approvals fuel, lubricating oils, coolants, water, air and inert gases

Reinforcement:

Temperature Range:

One polyester braid and one braid of high tensile

-49°C up to +149°C,

steel wire

except air (not to exceed 121°C) and

HYDRAULIC HOSES

HTAB / HTFH

water (not to exceed 82°C) Comment:

RUBBER HOSE

Cover:

Hose Tails:

Black synthetic rubber with black polyester textile Lay line example may not be a true indication

Pirtek ‘A’ Series (Field Attachable)

outer braid resistant to abrasion, oils, ozone and

Pirtek ‘R’ Series (Crimp)

of current status. Refer Pirtek for current

weathering. Permeable cover allows safe escape information of entrapped air when used to conduct high pressure air Lay line example: White Ink-Jet on black background. Note Comment above PIRTEK HI-TEMP AIR BRAKE 7.9MM (5/16”) HTAB-06 103 BAR (1500PSI) WORK. PRESS: 149°C. SAE J1402 TYPE AII 2Q07 PIRTEK HI-TEMP FLEX HOSE 22.4MM (7/8”) HTFH-16 28 BAR (400PSI) WORK. PRESS: 149°C. 2Q07

Product Code

Nominal ID

Pressure bar

Min bend radius

Weight

HTAB-04

mm 4.8

in 3/16

mm 13.7

working 138

min burst 552

mm 19.1

Kg/m 0.19

HTAB-05

6.4

1/4

15.7

103

412

25.4

0.24

HTAB-06

7.9

5/16

17.7

103

412

31.8

0.28

HTAB-08

10.4

13/32

20.1

345

44.5

0.33

HTAB-10

12.7

1/2

24.0

345

57.2

0.50

HTAB-12

15.9

5/8

27.9

207

69.9

0.58

HTFH-16

22.4

7/8

32.3

110

88.9

0.55

HTFH-20

28.7

1.1/8

38.9

114.3

0.68

HTFH-24

35.1

1.3/8

46.0

139.7

0.85

11 B

HYDRAULIC HOSES

JW210A

JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

Limitations:

One braid of high tensile steel wire

-40°C up to +155°C

Not suitable for steam and hydraulic applications

RUBBER HOSE

Cover:

Comment:

Hose Tails:

Pin pricked black synthetic rubber resistant to

Lay line example may not be a true indication

Pirtek ‘K’ Series

oils, ozone and weathering. Cover features a

of current status. Refer Pirtek for current

high level of abrasion resistance

information

Lay line example: Embossed text on a black abrasion resistant cover. Note Comment above PIRTEK JETWASH 6.5 mm (1/4”) JW210A-04 210 BAR (3045 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code JW210A-04 †

Nominal ID mm 6.4

OD mm in 1/4

Wire 11.1

Pressure bar Cover 13.4

working 210

min burst 840

Min bend radius

Weight

mm 45

Kg/m 0.20

Test Impulses 150 000

† See Comment above

HYDRAULIC HOSES

JW250 / JW250A JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

One braid of high tensile steel wire

-40°C up to +155°C Not suitable for steam and hydraulic applications Comment:

Hose Tails:

Pin pricked blue synthetic rubber resistant to

Lay line examples may not be a true indication

Pirtek ‘K’ Series all sizes

abrasion, oils, ozone and weathering. Specify

of current status. Refer Pirtek for current

JW250A for an even higher level of abrasion

information

resistance with black cover

Lay line example: White text on blue background (standard cover). Embossed text on black cover (abrasion resistant cover). Note Comment above PIRTEK JETWASH 9.5 mm (3/8”) JW250-06 250 BAR (3625 PSI) WORK PRESS MAX 155°C

RUBBER HOSE

Cover:

PIRTEK JETWASH 6.5 mm (1/4”) JW250A-04 250 BAR (3625 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code

Nominal ID

OD mm Wire 9.9

Pressure bar Cover 11.8

working 250

min burst 1000

Min bend radius mm 35

Weight Kg/m

Test Impulses

JW250-04 †

mm 6.4

in 1/4

JW250A-04 †

6.4

1/4

9.9

11.8

250

1000

150 000

JW250A-06 †

9.6

3/8

13.2

13.4

250

1000

150 000

† See Comment above

HYDRAULIC HOSES

JW400 / JW400A

2-WIRE JET WASH HOSE

Construction

Applications

Inner Tube: Synthetic rubber, resistant to water

Extremely flexible, high pressure compact hose

and detergents in aqueous solution

for pressure cleaners. Suitable for conducting water and detergents in aqueous solution

Reinforcement:

Temperature Range:

Two braid of high tensile steel wire

-40°C up to +155°C Not suitable for steam and hydraulic applications

RUBBER HOSE

Cover:

Comment:

Hose Tails:

Pin pricked blue synthetic rubber resistant to

Lay line examples may not be a true indication

Pirtek ‘K’ Series all sizes

abrasion, oils, ozone and weathering. Specify

of current status. Refer Pirtek for current

JW250A for an even higher level of abrasion

information

resistance with black cover

Lay line example: White text on blue background (standard cover). Embossed text on black cover (abrasion resistant cover). Note Comment above PIRTEK JETWASH 9.5 mm (3/8”) JW400-06 400 BAR (5800 PSI) WORK PRESS MAX 155°C PIRTEK JETWASH 69.5 mm (3/8”) JW400A-06 400 BAR (5800 PSI) WORK PRESS MAX 155°C ABRASION RESISTANT COVER

Product Code

Nominal ID

OD mm

Pressure bar

Min bend radius

Weight

JW400-06 †

mm 9.5

in 3/8

Wire 14.8

Cover 16.8

working 400

min burst 1520

mm 90

Kg/m 0.44

JW400A-06 †

9.5

3/8

13.2

13.4

400

1520

0.44

Test Impulses 150 000 150 000

† See Comment above

HYDRAULIC HOSES

R1AT

SINGLE WIRE BRAID

Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure hose for hydraulic fluids such

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

as mineral oils, aqueous emulsions, water, air

specifications:

and inert gases

SAE100 R1AT S EN853 1SN

Reinforcement:

Temperature Range:

Approvals:

One braid of high tensile steel wire

-40°C up to +100°C mineral oil

AS2660 test requirements-

-40°C up to +60°C water based fluids

AS1180 10B and AS1180.13A (FRAS)

Cover:

0°C up to +60°C water

MSHA approved

0°C up to +50°C air

Prolonged usage with water or water based fluids at temperatures above 70°C will allow

ozone and weathering

Cover must be pin pricked if hose is to be used

wire corrosion as a result of diffusion through the

to convey air above 17 bar

inner liner

Comment: Lay line example may not be a true indication

Hose Tails:

of current status. Refer Pirtek for current

Pirtek ‘K’ Series to 5/8”

information.

Pirtek ‘J’ Series 3/4” to 2”

Lay line example: White text on black background. Note Comment above PIRTEK SAE 100R1 AT TYPE S R1AT-04 6.4 mm (1/4”) 225 BAR (3263 PSI) FRAS

Product Code R1AT-03 †

Nominal Diameter DN 5

ins 3/16

mm 4.9

Reinforcement

OD mm

Pressure bar

Min. bend radius

Weight kg/m 0.18

1 braid

Cover 11.8

working 250

burst 1000

mm 90

R1AT-04

1/4

6.4

1 braid

13.7

225

900

100

0.23

R1AT-05 †

5/16

7.9

1 braid

15.0

215

850

115

0.27

R1AT-06

3/8

9.5

1 braid

17.7

180

720

125

0.37

R1AT-08

1/2

12.7

1 braid

20.8

160

640

180

0.45

R1AT-10 †

5/8

15.9

1 braid

23.6

140

560

201

0.50

R1AT-12

3/4

19.1

1 braid

28.0

105

420

240

0.62

R1AT-16

25.4

1 braid

36.2

352

300

0.93

R1AT-20

1 1/4

31.8

1 braid

47.6

252

420

1.36

R1AT-24

1 1/2

38.1

1 braid

54.0

200

500

1.70

R1AT-32

50.8

1 braid

68.3

160

630

2.43

RUBBER HOSE

Black synthetic rubber resistant to abrasion, oils,

-40°C up to +70°C ambient

† Non-standard product. Available to special order

HYDRAULIC HOSES

R1ATFS

SINGLE WIRE BRAID FIRE SUPPRESSION APPROVAL

Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure hose for hydraulic fluids

SAE J 517 (SAE 100R1AT)

Seamless synthetic rubber, resistant. to oil.

such as mineral and vegetable oils, aqueous

EN 853 1SN

emulsions and water.

Former DIN 20022 1SN (part 3) Meets hose requirements outlined in AS5062

Reinforcement:

Temperature Range:

One braid of high tensile steel wire.

-40°C up to +100°C (125°C intermittent)

Approvals: MSHA 2G in all sizes

RUBBER HOSE

Comment:

Approved within Australia for use on fire

Cover:

Lay line example may not be a true indication

suppression systems

Red synthetic rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

ozone and weathering

information.

Impulse Testing: All sizes tested to 150 000 cycles (hose only) Hose Tails: Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ Series 3/4”

Lay line example: White text on red background. Note Comment above PIRTEK R1ATFS — DIN EN 853 1SN 25mm (1”) R1AT-16 88 BAR (1,200 PSI) WORK. PRESS. MSHA

Nominal Diameter

Product Code

OD mm

Pressure bar

Min. bend radius

Weight

R1ATFS-04

DN 6

ins 1/4

mm 6.4

Wire 11.1

Cover 13.4

working 225

burst 900

mm 100

kg/m 0.23

R1ATFS-06

3/8

9.5

15.1

17.4

180

720

130

0.33

R1ATFS-08

1/2

12.7

18.3

20.6

160

640

180

0.41

R1ATFS-12

3/4

19.0

25.4

27.7

105

420

240

0.61

HYDRAULIC HOSES

R2AT/2SC

TWO WIRE BRAID

Construction

Applications

Reference Specifications

Inner Tube:

Medium to high pressure hose for hydraulic fluids Tested in accordance with performance

Seamless synthetic rubber, oil resistant

such as mineral oils, aqueous emulsions, water,

specifications:

air and inert gases

SAE100 R2AT EN853 2SN

Reinforcement: Two braids of high tensile steel wire

Cover: Black synthetic rubber resistant to abrasion, oils,

Approvals:

-40°C up to +100°C mineral oil

AS2660 test requirements-

-40°C up to +60°C water based fluids

AS1180.10B and AS1180.13A (FRAS)

0°C up to +60°C water

MSHA approved

0°C up to +50°C air

Prolonged usage with water or water based

-40°C up to +70°C ambient

fluids at temperatures above 70°C will allow

Cover must be pin pricked if hose is to be used

wire corrosion as a result of diffusion through the

to convey air above 17 bar

inner liner

Comment:

Hose Tails:

Lay line example may not be a true indication

Pirtek ‘K’ Series to 5/8”

of current status. Refer Pirtek for current

Pirtek ‘J’ Series 3/4” to 3”

information.

954, 934 Series 2.1/2” to 3”

Lay line example: White text on black background. Note Comment above

RUBBER HOSE

ozone and weathering

Temperature Range:

PIRTEK SAE 100R2AT R2AT-12 19.1 mm (3/4”) 215 BAR (3118 PSI) FRAS

Product Code

Nominal Diameter

Reinforcement

OD mm

Pressure bar

Min. bend radius

Weight

kg/m

ins

Cover

working

burst

R2AT-03 †

3/16

4.9

R2AT-04

1/4

6.4

2 braids

13.4

415

1650

0.30

2 braids

15.3

400

1600

100

0.37

R2AT-05 †

5/16

7.9

2 braids

16.6

350

1400

115

0.45

R2AT-06

R2AT-08

3/8

9.5

2 braids

19.3

330

1320

125

0.50

1/2

12.7

2 braids

22.4

275

1100

180

0.62

R2AT-10 R2AT-12

5/8

15.9

2 braids

25.8

250

1000

205

0.68

3/4

19.1

2 braids

29.8

215

860

240

0.89

R2AT-16

25.4

2 braids

38.5

165

660

300

1.45

R2AT-20

1 1/4

31.8

2 braids

49.6

125

500

420

2.25

R2AT-24

1 1/2

38.1

2 braids

56.0

360

500

2.61

R2AT-32

50.8

2 braids

68.6

320

630

3.31

R2AT-40

2 1/2

63.5

2 braids

80.9

276

762

3.80

2SC-40

2 1/2

63.5

2 braids

76.5

280

762

2.90

2SC-48 §

76.2

2 braids

90.5

70 §

280

900

3.98

† Non standard product. Available to special order § Safety factor only 3.4:1 when used in conjunction with 934 Series hose tails Note: 2SC-40 and 2SC-48 hoses are not included in Standard EN857-2SC

HYDRAULIC HOSES

R2ATHT

TWO WIRE BRAID HIGH TEMP.

Construction

Applications

Reference Specifications

Inner Tube:

Hydraulic system service with petroleum,

Exceeds SAE J 517 (SAE 100R2AT)

High temp. elastomer rubber, resistant to oil

fire resistant and water base fluids, fuel and

EN 853 2SN

lubricating systems

Former DIN 20022 2SN (part 4)

Temperature Range:

Approvals:

Reinforcement:

-40°C up to +150°C

MSHA

Two braids of high tensile steel wire

except: air not to exceed 121°C

FRAS AS1180.10B &13A

: water not to exceed 70°C

RUBBER HOSE

Comment:

Limitations:

Cover:

Lay line example may not be a true indication

Cover must be pin pricked if hose is to be used

Blue elastomer rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

to conduct air above 17 bar pressure

ozone and weathering

information.

Impulse Testing: All sizes tested to 200 000 cycles (hose only) Hose Tails: Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ Series 3/4” to 2”

Lay line example: White text on a dark blue layline. Note Comment above PIRTEK SAE 100 R2 AT — DIN EN 853 2SN “HIGH TEMP” 25mm (1”) R2ATHT-16 172 BAR (2494 PSI) WORK.PRESS: 150`C MAX MSHA-25 FRAS AS1180.10B & 13A

Product Code

Nominal Diameter

OD mm

Pressure bar

Min. bend radius

Weight

R2ATHT-04

DN 6

ins 1/4

mm 6.4

Wire 12.7

Cover 15.2

working 396

burst 1584

mm 102

kg/m 0.40

R2ATHT-06

3/8

9.5

16.7

19.2

345

1380

127

0.58

R2ATHT-08

1/2

12.7

19.8

22.1

293

1172

178

0.69

R2ATHT-10

5/8

15.9

23.0

25.1

224

896

203

0.81

R2ATHT-12

3/4

19.0

27.0

29.5

207

828

241

1.00

R2ATHT-16

25.4

34.9

37.8

172

688

305

1.45

R2ATHT-20

1 1/4

31.8

44.5

48.8

155

620

419

2.39

R2ATHT-24

1 1/2

38.1

50.8

54.6

120

480

508

2.59

R2ATHT-32

50.8

63.5

67.8

103

412

635

3.38

R2ATHT-32P *

50.8

63.5

68.6

103

412

635

3.40

* Perforated cover for pneumatic applications

HYDRAULIC HOSES

JH70

JACKING HOSE

Construction

Applications

Reference Specifications

Inner Tube:

High pressure hose for hydraulic fluids including

ISO 1307)

Seamless synthetic rubber, oil resistant

mineral and vegetable oil in hydraulic systems

Approvals:

for jacking applications

MSHA Approval No. IC-215/0

Temperature Range: -40°C up to +100°C mineral oil

Reinforcement:

Limitations:

+125°C intermittent

Two braids of high tensile steel wire

Only for use as jacking hose. Note reduced Safety Factor

Comment: Cover:

Lay line example may not be a true indication

Black synthetic rubber resistant to abrasion, oils,

of current status. Refer Pirtek for current

ozone and weathering

information.

Hose Tails:

with SRP Strain Relievers REFER M.A.P.S. WORK INSTRUCTION

RUBBER HOSE

Pirtek ‘K’ Series Use in conjunction

Lay line example: Red text on black background. Note Comment above PIRTEK JACKING HOSE JH70-04 6.4mm (1/4”) 700 BAR (10152 PSI) MSHA IC-215/0 ABRASION RESISTANT

Product Code

Reinforcement

Nominal Diameter

JH70-04

DN 6

ins 1/4

mm 6.4

JH70-06

3/8

9.5

OD mm

Pressure bar

Min. bend radius

Weight

2 braid

Cover 14.8

working 700

burst 1400

mm 80

kg/m 0.372

2 braid

19.0

700

1400

0.569

JH70-06 assembly with Strain Reliever attached to resist kinking of the hose at the end of the Ferrule

SRP-04 Strain Reliever

SRP-06 Strain Reliever

HYDRAULIC HOSES

C21

ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 210 bar working pressure across all sizes) hose for hydraulic fluids such as to oil

JIS K6349-3

mineral and vegetable oils, aqueous emulsions,

Approvals:

Reinforcement: 4 spirals of high tensile steel

water and inert gases

MSHA Approval No. IC-104/1 PAR No. 84844

wire

Prolonged usage with water or water based

FRAS AS1180.10B & 13A

fluids at temperatures above 70°C will allow Cover: Abrasion resistant black synthetic rubber

wire corrosion as a result of diffusion through the

Impulse Testing:

resistant to oils, ozone and weathering.

inner liner

Tested to 500 000 cycles @133% of

Cover loss by abrasion when tested in

Temperature Range:

accordance with ISO 6945 is less than 1.0 gram

-40°C up to +120°C mineral oil

after 2000 cycles.

-40°C up to +70°C water based fluids

working pressure in accordance with SAE 100 R12 requirements (hose only)

RUBBER HOSE

Hose Tails: Pirtek ‘J’ or ‘X’ Series

0°C up to +70°C water -40°C up to +70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on black hose. Note Comment above. PIRTEK C21 50 mm (2”) C21-32 210 BAR (3,000 PSI) MSHA IC-104/1 ABRASION RESISTANT

Product Code C21-32

Nominal Diameter DN 51

ins 2”

OD mm mm 50.8

Wire 63.6

Cover 66.7

Pressure bar working 210

burst 840

Min. bend radius

Weight

Performance Standard

mm 500

kg/m 4.20

SAE R12

ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 250 bar working pressure across all sizes) hose for hydraulic fluids such as to oil

Meets or exceeds SAE J 517 (100 R16) Meets or exceeds EN 857 2SC

mineral and vegetable oils, aqueous emulsions,

Tested in accordance with SAE J517, EN856,

Reinforcement: Two braids of high tensile steel

water and inert gases

AS3791

wire, or 4 spirals of high tensile steel wire

Prolonged usage with water or water based

Approvals:

fluids at temperatures above 70°C will allow

MSHA Approval No. IC-104/1 PAR No. 84844

Cover: Abrasion resistant black synthetic

wire corrosion as a result of diffusion through the

applies to all sizes

PVC nitrile rubber resistant to oils, ozone and

inner liner

Impulse Testing:

HYDRAULIC HOSES

C25

Refer to the Table for Impulse Test criteria

weathering

Braided hoses as per SAE 100 R2

Cover loss by abrasion when tested in

Spiral hoses:

Spiral hoses as per SAE 100 R12

accordance with ISO 6945 is less than 1.0 gram

-40°C up to +120°C mineral oil

after 2000 cycles

-40°C up to +70°C water based fluids

RUBBER HOSE

Temperature Range:

Hose Tails:

0°C up to +70°C water

Pirtek ‘K’ Series to 5/8”

-40°C up to 70°C air

Pirtek ‘J’ Series 3/4”, 1”

Braided Hoses:

Pirtek ‘J’ or ‘X’ Series 1 1/4”, 1 1/2”

-40°C up to +100°C mineral oil -40°C up to +60°C water based fluids 0°C up to +60°C water -40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on black hose. Note Comment above PIRTEK C25 SERIES III 25mm (1”) C25-16 250 BAR (3,500 PSI) W.P. MSHA IC-104/1 ABRASION RESISTANT

Product Code

Nominal Diameter

C25-10

DN 16

ins 5/8

mm 15.9

C25-12

3/4

19.0

C25-16

25.4

C25-20

1 1/4

32.2

C25-24

1/2

38.5

Type

OD mm

Pressure bar

Min. bend radius

Weight

Test Perform. Impulses Standard

Wire 23.0

Cover 25.2

working 280

burst 1120

mm 170

kg/m 0.80

EN/SAE No. 200 000 2SC

2 braid

26.2

29.1

250

1000

200

1.00

200 000

R16

2 braid

32.9

35.6

250

1000

250

1.30

200 000

2SC

4 spiral

43.9

47.0

250

1000

350

2.70

500 000

2SC

4 spiral

48.8

53.5

250

1000

450

3.20

500 000

2SC

2 braid

HYDRAULIC HOSES

PC28PS

ISOBARIC CLASS HOSE ULTRA HIGH ABRASION RESISTANCE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 275 bar working pressure across all sizes) hose for hydraulic fluids such as to oil

Meets or exceeds SAE J 517 (100 R12) for impulse requirements

mineral and vegetable oils, aqueous emulsions,

Meets or exceeds JIS K6349

Reinforcement: 4 spirals of high tensile steel

water and inert gases

Tested in accordance with SAE J517, EN856,

wire

Prolonged usage with water or water based

AS3791

fluids at temperatures above 70°C will allow

Approvals:

RUBBER HOSE

Cover: Utmost abrasion resistant UHWMPE over wire corrosion as a result of diffusion through the inner liner black synthetic rubber, resistant to oils, ozone Improved bending radius for underground and weathering drilling machines

MSHA Approval No. IC104/1

Cover loss by abrasion when tested in

Refer to the Table for Impulse Test criteria

accordance with ISO 6945 is 0.0 gram after 500,000 cycles

Temperature Range:

AS2660 test requirements AS1180 10B and 13A (FRAS) Impulse Testing: Spiral hoses as per SAE 100 R12

-40°C up to +100°C mineral oil

Meets or exceeds JIS B8360 for heavy duty

-40°C up to +70°C water based fluids

applications

0°C up to +70°C water -40°C up to 70°C air

Hose Tails: Pirtek ‘J’ Series 1/2”, 3/4”, 1”

Comment: Lay line example may not be a true indication

(Refer Pirtek for current Fitting Series)

of current status. Refer Pirtek for current information.

Lay line example: White text on black hose. Note Comment above PIRTEK PC28PS 25mm (1”) 280 BAR (4,000 PSI) W.P. FRAS MSHA IC104/1 ULTRA HIGH ABRASION RESISTANT

Nominal Diameter

Product Code

PC28PS-08

DN 13

ins 1/2

mm 12.7

PC28PS-12

3/4

19.0

PC28PS-16

25.4

Type

OD mm

Pressure bar

Min. bend radius

Weight

Test Impulses

4 spiral

Wire 20.0

Cover 23.0

working 280

burst 1120

mm 110

kg/m 0.78

No. 500 000

4 spiral

27.0

29.9

280

1120

170

1.13

500 000

4 spiral

33.9

36.8

280

1120

220

1.86

500 000

ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 350 bar working pressure across all sizes) hose for hydraulic fluids such as to oil

Meets or exceeds SAE J 517 (100 R12, R13 or R16) Meets or exceeds EN 857 2SC

Reinforcement: Two braids of high tensile steel

water and inert gases

Tested in accordance with SAE J 517, EN856,

wire, or 4-6 spirals of high tensile steel wire

Prolonged usage with water or water based

AS3791

fluids at temperatures above 70°C will allow

Approvals:

Cover: Abrasion resistant black synthetic

wire corrosion as a result of diffusion through the

MSHA Approval No. IC-104/1 PAR No. 84844 on

PVC nitrile rubber resistant to oils, ozone and

inner liner

all sizes

weathering

Temperature Range:

Impulse Testing:

Spiral hoses:

Refer to the Table for Impulse Test criteria

Cover loss by abrasion when tested in

-40°C up to +120°C mineral oil

Braided hoses as per SAE 100 R2

accordance with ISO 6945 is less than 1.0 gram

-40°C up to +70°C water based fluids

Spiral hoses as per SAE 100 R13

RUBBER HOSE

mineral and vegetable oils, aqueous emulsions,

0°C up to +70°C water

after 2000 cycles

-40°C up to 70°C air

Hose Tails:

Braided hoses:

Pirtek ‘K’ Series to 5/8”

-40°C up to +100°C mineral oil

Pirtek ‘J’ Series 3/4”, 1”

-40°C up to +60°C water based fluids

Pirtek ‘X’ Series 1”, 1 1/4”, 1 1/2”,2”

0°C up to +60°C water

HYDRAULIC HOSES

C35

Interlock option 3/4” and above

-40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: White text on braided hoses. Red text on spiral hoses. Note Comment above PIRTEK CLASS 35 9.5mm (3/8”) C35-06 350 BAR (5000 PSI) MSHA IC-104/1 ABRASION RESISTANT

Nominal Diameter

Product Code

Type

OD mm

Pressure bar

ins

C35-05

5/16

7.9

C35-06

3/8

9.5

2 braid

15.3

17.2

350

1400

0.42

200 000

R16

C35-08

1/2

12.7

2 braid

20.1

22.2

350

1400

130

0.62

200 000

R16

C35-10 †

5/8

16.1

4 spiral

23.7

27.4

350

1400

200

1.00

500 000

R12

C35-12

3/4

19.2

4 spiral

28.1

30.7

350

1400

220

1.50

500 000

R13

C35-16

25.6

4 spiral

35.6

38.7

350

1400

280

2.20

500 000

R13

C35-20

1 1/4

32.2

6 spiral

45.6

48.7

350

1400

380

3.70

500 000

R13

C35-24

1 1/2

38.5

6 spiral

52.5

55.6

350

1400

480

4.40

500 000

R13

51 2 51.2 6 spiral 68.1 C35-32 † Meets or exceeds SAE100 R12 except for reinforcement OD

71.1

350

1400

600

6.90

500 000

R13

2 braid

Wire

Cover

working

13.0

14.7

380

Min. bend Weight Test Perform. radius Impulses Standard burst mm kg/m No. SAE 1520

0.34

200 000

R16

HYDRAULIC HOSES

C42

ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 420 bar working pressure across all sizes) hose for hydraulic fluids such as to oil

Tested in accordance with SAE J517, EN856, AS3791

mineral and vegetable oils, aqueous emulsions,

Approvals:

Reinforcement: Two braids of high tensile steel

water and inert gases

MSHA Approval No. IC-104/1 PAR No. 84844

wire (C42-04), or 4-6 spirals of high tensile steel

Prolonged usage with water or water based

(C42EH-32 has MSHA Approval IC-8/13)

wire

fluids at temperatures above 70°C will allow

FRAS AS1180.10B & 13A

wire corrosion as a result of diffusion through the Cover: Abrasion resistant black synthetic rubber

inner liner

Impulse Testing: Refer to the Table for Impulse Test criteria

resistant to oils, ozone and weathering (PVC

RUBBER HOSE

Temperature Range:

Braided hoses as per SAE 100 R2

Spiral hoses:

Spiral hoses as per SAE 100 R12, R15

Cover loss by abrasion when tested in

-40°C up to +120°C mineral oil

C42EH data applicable only in conjunction with

accordance with ISO 6945 is less than 1.0 gram

-40°C up to +70°C water based fluids

EH Series interlock tails

nitrile rubber on braided hoses)

0°C up to +70°C water

after 2000 cycles

-40°C up to 70°C air

Hose Tails:

Braided hoses:

Pirtek ‘K’ Series to 1/2”

-40°C up to +100°C mineral oil

Pirtek ‘J’ Series 3/8” and 1/2”

-40°C up to +60°C water based fluids

Pirtek ‘H’ Series 3/4”

0°C up to +60°C water

Pirtek ‘X’ Series 3/4”, 1”

-40°C up to 70°C ambient

Interlock 1” to 1.1/2”

Comment:

Special Interlock for C42EH

Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on braided hoses. Yellow text on spiral hoses. Note Comment above

† MSHA Approval pending PIRTEK CLASS 42 19 mm (3/4”) C42-12 420 BAR (6,000 PSI) WORK.PRESS. MSHA IC-104/1 ABRASION RESISTANT PIRTEK CLASS 42 SERIES EH 50MM (2”) C42EH-32 420 BAR (6,000 PSI) EN856 MSHA IC-8/13 1Q09

Product Code

Nominal Diameter

Type

OD mm

Pressure bar

Perform. Min. bend Test Weight radius Impulses Standard

2 braid

Wire 12.7

Cover 14.9

working 420

burst 1680

mm 75

kg/m 0.40

EN/SAE No. 200 000 2SC

9.7

4 spiral

17.2

20.2

420

1680

125

0.70

500 000

R12

1/2

12.9

4 spiral

20.7

23.8

420

1680

180

0.90

500 000

R12

3/4

19.2

4 spiral

28.1

32.0

420

1680

280

1.50

500 000

R15

25.7

4 spiral

35.1

38.2

420

1680

300

2.20

500 000

R15

C42-20

1 1/4

32.2

6 spiral

46.8

49.8

420

1680

400

3.90

500 000

R15

C42EH-20

1 1/4

32.2

6 spiral

46.8

49.4

420

1680

420

3.48

2000000

R15

C42-24

1 1/2

38.5

6 spiral

54.0

57.2

420

1680

500

4.70

500 000

R15

C42EH-24

1 1/2

38.5

6 spiral

53.4

57.3

420

1680

500

4.63

2000000

R15

C42-32

51.2

6 spiral

70.6

75.0

420

1680

600

7.90

500 000

R15

C42EH-32

51.2

6 spiral

67.3

71.6

420

1680

630

6.70

2 000 000

R15

C42-04

DN 6

ins 1/4

mm 6.4

C42-06

3/8

C42-08

C42-12

C42-16

HYDRAULIC HOSES

PC25

PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 250 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE 100R16 (braided hose)

Reinforcement:

inert gases

SAE 100R12 (spiral hose)

Two braids, or 4 spirals of high tensile steel wire

Excellent compact bend radius

Approvals:

Temperature Range:

AS2660 test requirements-

Cover:

Spiral hoses:

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistance black synthetic rubber

-40°C up to +120°C mineral oil

resistant to oils, ozone and weathering

-40°C up to +70°C water based fluids

Prolonged usage with water or water based

0°C up to +70°C water

fluids at temperatures above 70°C will allow wire corrosion as a result of diffusion through the

Braided Hoses:

inner liner

-40°C up to +100°C mineral oil

Hose Tails:

-40°C up to +60°C water based fluids

Pirtek ‘K’ Series to 5/8”

0°C up to +60°C water

Pirtek ‘J’ Series 3/4”, 1”

-40°C up to 70°C ambient

Pirtek ‘J’ or ‘X’ Series 1 1/4”, 1 1/2”

Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current

RUBBER HOSE

-40°C up to 70°C air

information.

Lay line example: White text on black background. Note Comment above PIRTEK PC25-12 19.1MM (3/4”) 250 BAR (3625 PSI) W.P. FRAS ABRASION RESISTANT

Product Code

Nominal Diameter

Reinforcement

OD (mm)

Pressure bar

Min. bend radius

Weight

PC25-10

DN 16

ins 5/8

mm 15.9

2 braid

26.0

W.P. 250

Min. Burst 1000

mm 140

Kg/m 0.84

PC25-12

3/4

19.1

2 braid

29.1

250

1000

170

0.96

PC25-20

1 1/4

31.8

4 spiral

44.9

250

1000

280

2.36

PC25-24

1/2

38.1

4 spiral

52.4

250

1000

330

3.06

HYDRAULIC HOSES

PC35

PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 350 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE R16 (braided hose)

Reinforcement:

inert gases

SAE 100 R12 (spiral hose)

Two braids, 4spirals or 6 spirals of high tensile

Excellent compact bend radius

SAE 100 R13 / R15 (spiral hose)

steel wire

Temperature Range:

Approvals:

Spiral hoses:

AS2660 test requirements-

Cover:

-40°C up to +120°C mineral oil

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistant black synthetic rubber

-40°C up to +70°C water based fluids

RUBBER HOSE

0°C up to +70°C water

Prolonged usage with water or water based

-40°C up to +70°C ambient

fluids at temperatures above 70°C will allow

Braided hoses:

wire corrosion as a result of diffusion through the

-40°C up to +100°C mineral oil

inner liner

resistant to oils, ozone and weathering

-40°C up to +60°C water based fluids 0°C up to +60°C water

Hose Tails:

-40°C up to 70°C ambient

Pirtek ‘K’ Series to 5/8”

Comment:

Pirtek ‘J’ Series 3/8” to 1”

Lay line example may not be a true indication

Pirtek ‘X’ Series 1” to 2”

of current status. Refer Pirtek for current

Pirtek Interlock Series 3/4” to 1.1/2”

information. Lay line example: White text on black background. Note Comment above PIRTEK CLASS PC35-12 19.1MM (3/4”) 350 BAR (5076 PSI) FRAS ABRASION RESISTANT

Nominal Diameter

Product Code

Reinforcement

ins

PC35-06

3/8

9.5

2 braids

PC35-08

1/2

12.7

PC35-10

5/8

PC35-12

3/4

PC35-16

PC35-20 PC35-24

O.D. mm

Pressure bar

Min. bend radius

Weight

W.P.

Min. Burst

Kg/m

18.9

350

1400

0.55

4 spirals

22.2

350

1400

110

0.80

15.9

4 spirals

26.4

350

1400

140

1.00

19.1

4 spirals

29.0

350

1400

170

1.13

25.4

4 spirals

36.6

350

1400

220

2.00

1 1/4

31.8

6 spirals

48.7

350

1400

280

3.80

1 1/2

38.1

6 spirals

55.6

350

1400

330

4.60

HYDRAULIC HOSES

PC42

PIRTEK CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Isobaric (constant 420 bar working pressure

Tested in accordance with performance

Seamless synthetic rubber, oil resistant

across all sizes) hose for hydraulic fluids such as

specifications:

mineral oils, aqueous emulsions, water, air and

SAE 100 R16 (braided hose)

Reinforcement:

inert gases

Approvals:

Two braids of high tensile steel wire

Excellent compact bend radius

AS2660 test requirements-

Cover:

Temperature Range:

AS1180.10B and AS1180.13A (FRAS)

High abrasion resistance black synthetic rubber

Spiral hoses:

resistant to oils, ozone and weathering

-40°C up to +120°C mineral oil

Prolonged usage with water or water based

-40°C up to +70°C water based fluids

fluids at temperatures above 70°C will allow

0°C up to +70°C water

wire corrosion as a result of diffusion through the

RUBBER HOSE

-40°C up to 70°C ambient

inner liner.

Braided hoses: -40°C up to +100°C mineral oil

Hose Tails:

-40°C up to +60°C water based fluids

Pirtek ‘K’ Series

0°C up to +60°C water -40°C up to 70°C ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information. Lay line example: White text on black background. Note Comment above PIRTEK CLASS PC42-04 6.4 MM (1/4”) 420 BAR (6091 PSI) FRAS ABRASION RESISTANT

Product Code PC42-04

Nominal Diameter DN 6

ins 1/4

mm 6.4

Reinforcement

OD (mm)

2 braids

14.9

Pressure (bar) W.P. 420

Min. Burst 1680

Min. bend radius

Weight

mm 70

Kg/m 0.39

HYDRAULIC HOSES

C45

ISOBARIC CLASS HOSE

Construction

Applications

Reference Specifications

Inner Tube: Synthetic rubber, resistant to oil

High pressure hose for hydraulic fluids such as

Tested in accordance with performance

mineral oils, aqueous emulsions, vegetable oils,

specifications:

Reinforcement: 4 spirals of high tensile steel

water, air and inert gases.

DIN EN 856 4SH

wire

Especially used for “Dynapac” style rollers. NOTE: THIS HOSE MUST ONLY BE USED FOR

Cover: Abrasion resistant black synthetic rubber

STATIC APPLICATIONS – Not recommended for

Approvals:

resistant to oils, ozone and weathering.

impulsing applications

MSHA Approval No. IC-188

Temperature Range: -40°C up to +100°C mineral oil

Hose Tails:

RUBBER HOSE

-40°C up to +60°C water based fluids

Pirtek ‘B’ Series

0°C up to +60°C water

(2-piece system requires a separate

-40°C up to +70°C ambient

SFB ferrule)

Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: Orange text on black background. Note Comment above PIRTEK CLASS 45 C45-10 15.9mm (5/8”) 450 BAR (6500 PSI) MSHA

Product Code C45-10

Nominal Diameter DN 16

ins 5/8

mm 15.9

Reinforcement

4 spiral

O.D. Cover mm 28.5

Pressure bar working 450

burst 1800

Min. bend radius

Weight

mm 250

kg/m 1.30

LARGE BORE HOSE

Construction

Applications

Reference Specifications

Inner Tube: Seamless synthetic

Medium pressure hose for hydraulic fluids

SAE J517 except for reinforcement OD

rubber, resistant. to oil

such as mineral and vegetable oils, aqueous emulsions and water

Approvals: MSHA Approval No. IC-104/1 PAR No. 84844

Reinforcement: Four spirals of high

FRAS AS1180.10B & 13A

Prolonged usage with water or water based

tensile steel wire.

HYDRAULIC HOSES

JBF

fluids at temperatures above 70°C will allow Cover: Abrasion resistant black synthetic rubber

wire corrosion as a result of diffusion through the

resistant to oils, ozone and weathering

inner liner Temperature Range:

RUBBER HOSE

-40°C up to +100°C mineral oil

Hose Tails: Pirtek ‘BSMS’ Series

-40°C up to +70°C water based fluids 0°C up to +70°C water -40°C up to 70°C air / ambient Comment: Lay line example may not be a true indication of current status. Refer Pirtek for current information.

Lay line example: Light yellow text on black hose. Note Comment above PIRTEK JUMBO ACE 63mm (2 1/2”) JBF-40 140 BAR (2030 PSI) WP MSHA IC/104/1 FRAS ABRASION RESISTANT

Product Code JBF-40

Nominal Diameter DN 63

ins 2.1/2

Type mm 63.5

4 spiral

OD mm Cover 82.4

Pressure bar working 140

burst 560

Min. bend radius

Weight

Test Impulses

mm 660

kg/m 5.5

No. 500 000

HYDRAULIC HOSES

LPG

LP GAS AS1869 CLASS D

Construction

Applications

Reference Specifications

Inner Tube:

High pressure hose for transfer of LPG, butane-

Meets and / or exceeds:

Conductive Teflon®

propane on stationary and mobile LPG gas

AS1869 Class D

engines. Ideal for forklift, automotive, light &

Very low extractables and permeation rate.

Reinforcement:

medium duty truck and transfer

Approvals:

Single braid of stainless steel wire

Temperature Range:

AGA (Aust. Gas Association)

Cover:

-20°C up to +125°C

Black and blue fire retardant, abrasion resistant

Comment:

aramid polyester

Lay line example may not be a true indication

Pirtek ‘G’ Series

of current status. Refer Pirtek for current

Special procedures apply using dedicated

information.

dies and spacers.

RUBBER HOSE

Thermoplastic tag required on all hose assemblies.

Lay line example: Hose does not have layline. Note Comment above

Product Code LPG-06

Nominal Diameter DN 10

16 LPG-10† † Limited stock available

Hose Tails:

Reinforcement

OD (mm)

ins 5/16

mm 7.9

1 wire braid

1/2

12.7

1 wire braid

Pressure (bar)

Min. bend radius

Weight

13.6

W.P. 26

Min. Burst 104

mm 101.6

Kg/m 0.18

19.1

104

165.1

0.27

HYDRAULIC HOSES

R12C

SPIRAL SAE100 R12 HOSE

Construction

Applications

Reference Specifications

Inner Tube: Fabric reinforced synthetic rubber,

High pressure hose for hydraulic fluids such as

SAE J 517 (100 R12)

resistant to oil

glycol, mineral oils, fuels, hydrocarbons etc.

EN 856 R12

Designed for applications where flexibility and Reinforcement: Four spirals of high tensile steel

high temperature resistance are required.

Approvals:

wire separated by layers of synthetic rubber

Compatible with Caterpillar® reusable fittings.

US MSHA IC-101

Temperature Range:

Impulse Testing:

-40°C up to +121°C mineral oil

1 000 000 impulses @ 133% of working pressure

Cover: Black synthetic rubber resistant to abrasion, oils, ozone and weathering

for all sizes. Additionally, hose is aged by heating Comment:

and cooling prior to testing. Hose only

RUBBER HOSE

Lay line example may not be a true indication of current status. Refer Pirtek for current

Hose Tails:

information

Pirtek ‘K’ Series to 5/8” Pirtek ‘J’ or ‘X’ Series 3/4” upwards Caterpillar® re-useable

Lay line example: Yellow text on black hose. Note Comment above XT® Technology SAE 100R12 ¾” Max WP 4000psi MSHA IC-101/10 Made in USA

Product Code

Nominal Diameter

OD mm

Type

Pressure bar

Min. Bend Radius

Weight

mm 64

kg/m 0.70

R12C-06

DN 10

ins 3/8

mm 9.5

4 spiral

Wire 17.2

Cover 20.2

working 276

burst 1104

R12C-08

1/2

4 spiral

20.7

23.8

276

1104

0.83

R12C-10

5/8

4 spiral

24.6

27.2

276

1104

102

1.20

R12C-12

3/4

4 spiral

27.6

30.7

276

1104

121

1.43

R12C-16

4 spiral

34.9

276

1104

153

2.00

R12C-20

1.1/4

4 spiral

43.9

207

828

210

2.80

R12C-24

1.1/2

4 spiral

50.4

53.4

172

688

254

3.40

R12C-32

4 spiral

63.6

66.7

172

688

318

4.25

HYDRAULIC HOSES

R13C

SPIRAL SAE100 R13 HOSE

Construction

Applications

Reference Specifications

Inner Tube: Fabric reinforced synthetic rubber,

Very high pressure hose for hydraulic fluids such

SAE J 517 (100 R13)

resistant to oil

as glycol, mineral oils, fuels, hydrocarbons etc.

EN 856 R13

Reinforcement: Four or six spirals of high

Specifically designed for applications where

Approvals:

tensile steel wire separed by layers of synthetic

high pulsating pressure, flexibility and high

US MSHA IC-101

rubber

temperature resistance are required. Compatible

Cover: Black synthetic rubber resistant to

with Caterpillar® reusable fittings

Impulse Testing: 1 000 000 impulses @ 120% of working pressure

abrasion, oils, ozone and weathering.

RUBBER HOSE B

for all sizes. Additionally, hose is aged by heating

-40°C up to +121°C mineral oil

and cooling prior to testing. Hose only

Comment:

Hose Tails:

Lay line example may not be a true indication

Pirtek ‘X’ Series all sizes

of current status. Refer Pirtek for current

Interlock option 1 1/4” upwards

information

Caterpillar® re-useable

Lay line example: Red text on black hose. Note Comment above XT® Technology SAE 100R13 1” Max WP 5000psi MSHA IC-101/10 Made in USA

Product Code

Temperature Range:

Nominal Diameter

OD mm

Type

R13C-12

DN 19

ins 3/4

mm 19

R13C-16

R13C-20

1.1/4

R13C-24

1.1/2

R13C-32

Pressure bar

Min. Bend Radius

Weight

4 spiral

Wire 29.0

Cover 32.1

working 345

burst 1380

mm 141

kg/m 1.75

4 spiral

35.6

38.7

345

1380

153

2.30

6 spiral

46.8

49.8

345

1380

210

3.70

6 spiral

54.3

57.3

345

1380

254

4.65

6 spiral

68.1

71.1

345

1380

318

6.90

HYDRAULIC HOSES

WB1000

WATERBLAST HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Very high constant pressure hose for water

AS/NZS 4233.2

Synthetic rubber, resistant. to oils

scaling systems. Suitable for passage of water and aqueous solutions Temperature Range:

Four spirals of high tensile steel wire

-40°C up to +80°C

Cover:

Comment:

Hose Tails:

Black synthetic rubber extremely resistant to

Lay line example may not be a true indication

I / IFWB (Interlock)

abrasion, oils, and weathering

of current status. Refer Pirtek for current

RUBBER HOSE

Reinforcement:

information

Lay line example: Moulded into outer cover. Note Comment above PIRTEK® WATERBLAST 3/4” DN19 W.P. 1000 BAR B.P. 2500 BAR

Product Code WB1000-12

Nominal ID

OD mm

Pressure bar

Min bend radius

Weight

Wire

Cover

working

min burst

Kg/m

3/4

29.0

1000

2500

250

1.73

HYDRAULIC HOSES

WB1100

WATERBLAST HOSE Construction

Applications

Reference Specifications

Inner Tube:

Very high constant pressure hose for water

AS/NZS 4233.2

Synthetic rubber, resistant. to oils

scaling systems. Suitable for passage of water and aqueous solutions

Reinforcement:

Temperature Range:

Four spirals of high tensile steel wire

-40°C up to +80°C

Cover:

Comment:

Hose Tails:

Black synthetic rubber extremely resistant to

Lay line example may not be a true indication

I / IFWB (Interlock)

abrasion, oils, and weathering

of current status. Refer Pirtek for current information

RUBBER HOSE

Lay line example: Moulded into outer cover. Note Comment above PIRTEK® WATERBLAST 1/2” DN12 W.P. 1100 BAR B.P. 2750 BAR

Product Code WB1100-08

Nominal ID

OD mm

Pressure bar

Min bend radius

Weight

Wire

Cover

working

min burst

Kg/m

1/2

12.7

21.5

24.5

1100

2750

230

1.12

BROAD SPECTRUM HOSE Construction

Applications

Reference Specifications

Inner Tube:

Flexible even in cold temperatures. Small outside Exceeds SAE J517 (R18)

composite wall dual extrusion smooth seamless

diameter and good flexibility over sheaves

SAE J343 Test procedures

polymeric (polyester) inner and polyurethane

allows use over a wide range of forklift sheaves,

ASTM D-380 Testing Rubber hoses

adjacent

including freezer applications.

ASTM D-622 Testing for Automotive Brake

Other applications include construction, general

Systems

hydraulics, chemical and gas transfer, machine

HYDRAULIC HOSES

30CT

tools, agricultural equipment etc Temperature Range:

Impulse Testing:

braided synthetic fibre in either single or dual

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

layer

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids

Volumetric Expansion:

THERMOPLASTIC HOSE

Reinforcement:

Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details Cover:

Comment:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Pirtek ‘S7’ or ‘S18’ Series

bonded to the reinforcement

of current status. Refer Pirtek for current

(refer Table for Die)

information

Pirtek ‘T’ Series option

Hose Tails:

Lay line example: White text on black hose. Note Comment above SYNFLEX® 30CT-06 SAE 100R18 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Product Code

Nominal ID

OD mm 12.1

working 207

min burst 828

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 32

Kg/100m 8.9

Die 45403W4

DN 6.4

mm 1/4

30CT-05

5/16

15.5

207

828

14.7

305

30CT-06

9.5

3/8

16.8

207

828

18.2

306

30CT-08

12.7

1/2

21.6

207

828

24.7

A0800

30CT-10

5/8

207

828

102

41.4

N10

S18

30CT-04

in 6

Pressure bar

Series S7

HYDRAULIC HOSES

3JET

WATER JETTING HOSE

Construction

Applications

Inner Tube:

Medium pressure hose for water jetting and drain ISO 7751

Smooth seamless thermoplastic (nylon)

cleaning. Low elongation

Reinforcement:

Temperature Range:

Spiral or braided synthetic fibre

-40°C up to +66°C water

Cover:

Comment:

Hose Tails:

Black, perforated bonded polyurethane

Lay line example may not be a true indication

Pirtek ‘S7’ series (refer below table for dies)

of current status. Refer Pirtek for current

Pirtek ‘T’ series

THERMOPLASTIC HOSE

information

Lay line example: White text on black hose. Note Comment above SYNFLEX® PIRJET 3JET-03 4.9mm (3/16”) 331 BAR (4800 PSI) WATER JETTING

Product Code

Reference Specifications

Nominal ID

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

3JET-03

DN 5

mm 3/16

in 4.9

mm 10.8

working 331

min burst 827

mm 19

Kg/100m 6.8

Die 4540303

Series S7

3JET-04

1/4

6.4

13.0

331

827

8.5

304

TWIN-LINE BROAD SPECTRUM HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Flexible even in cold temperatures. Small outside Exceeds SAE J517 (R18)

composite wall dual extrusion smooth seamless

diameter and good flexibility over sheaves

SAE J343 Test procedures

polymeric (polyester) inner and polyurethane

allows use over a wide range of forklift sheaves,

ASTM D-380 Testing Rubber hoses

adjacent

including freezer applications.

ASTM D-622 Testing for Automotive Brake

Other applications include construction, general

Systems

HYDRAULIC HOSES

30CTX2

hydraulics, chemical and gas transfer, machine tools, agricultural equipment etc Temperature Range:

Impulse Testing:

braided synthetic fibre in either single or dual

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

layer

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids

Volumetric Expansion: Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details

Cover:

Comment:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Pirtek ‘S7’ or ‘S18’ Series

bonded to the reinforcement

of current status. Refer Pirtek for current

(refer Table for Die)

information

Pirtek ‘T’ Series option

Hose Tails:

Lay line example: White text on black hose. Note Comment above SYNFLEX® 30CT-06 SAE 100R18 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Product Code

Nominal ID DN 6.4

mm 1/4

30CTX2-05

30CTX2-06

9.5

30CTX2-08

30CTX2-04

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

in 6

mm 12.1

working 207

min burst 828

mm 32

Kg/100m 8.9

Die 45403W4

Series S7

5/16

15.5

207

828

14.7

305

3/8

16.8

207

828

18.2

306

12.7

1/2

21.6

207

828

24.7

A0800

5/8

27.0

207

828

102

41.4

N10

S18

30CTX2-10 † † Non-standard product. Available to special order

THERMOPLASTIC HOSE

Reinforcement:

HYDRAULIC HOSES

3130

MEDIUM PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulics, high pressure gas transfer,

SAE J517 (R7)

smooth seamless thermoplastic (nylon)

chemical transfer. Low elongation, best value

SAE J343

100R7 hose.

ASTM D-380

Not for use over pulleys.

ASTM D-622

Absorbs shock loads and damaging pressure spikes through controlled expansion.

THERMOPLASTIC HOSE

Reinforcement:

Temperature Range:

Impulse Testing:

spiralled or braided synthetic

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only) at 133% WP Comment:

Perforated bonded black polyurethane

Lay line example may not be a true indication

Pirtek ‘S7’ Series (refer Table for Die)

of current status. Refer Pirtek for current

Pirtek ‘T’ Series option

information

Lay line example: White text on black hose. Note Comment above SYNFLEX® 3130-06 SAE 100R73/8” W.P 2250 P.S.I. (155 BAR) SAINT-GOBAIN

Product Code

Hose Tails:

Cover:

Nominal ID

OD in 3.2

mm 8.5

Pressure bar working 172

min burst 689

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 13

Kg/100m 3.87

Die 4540302

3130-02

DN 3

mm 1/8

Series S7

3130-03

3/16

10.8

207

827

6.70

303

3130-04

1/4

6.4

12.9

207

827

9.08

304

3130-05

5/16

15.1

172

689

11.16

305

3130-06

3/8

9.5

16.7

155

620

12.5

306

3130-08

1/2

12.7

20.7

138

552

76.2

16.97

308

3130-12

3/4

27.1

345

127

26.19

312

3130-16

25.4

34.0

276

203

46.28

316

HYDRAULIC HOSES

3360X2

TWIN-LINE FOR FORKLIFTS

Construction

Applications

Reference Specifications

Inner Tube:

Flexible even in cold temperatures.

SAE 100R17

Nylon

Small outside diameter and good flexibility over sheaves allows use over a wide range of forklift sheaves, including freezer applications. Other applications include construction, general hydraulics, chemical and gas transfer, machine tools, agricultural equipment etc. Temperature Range:

Impulse Testing:

braided synthetic fibre

-54°C up to +94°C for hydraulic fluids

Hoses are tested to withstand 200 000 impulse

-54°C up to +66°C for water based and fire

cycles (hose only) at 133% WP

resistant fluids Volumetric Expansion (per line): Typically 10 cc per metre for 1/4” at WP 20cc per metre for 1/2” at WP Consult Pirtek for details Hose Tails:

Cover:

Comment:

black non stick perforated polymeric (polyester)

Lay line example may not be a true indication

Pirtek ‘S8’ (refer Table for Die)

of current status. Refer Pirtek for current

Pirtek ‘200/SN8’ Series option

information

THERMOPLASTIC HOSE

Reinforcement:

Lay line example: White text on black hose. Each line is branded as though a single line. Note Comment above SYNFLEX® 3360-06 SAE 100R17 3/8” W.P 3000 P.S.I. (207 BAR) SAINT-GOBAIN

Product Code 3360X2-06 †

Nominal ID DN 9.5

mm 3/8

OD in 10

mm 18.4

Pressure bar working 207

min burst 828

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 51

Kg/100m 56.8

Die 4540J06N

Series S8

† Please note that this hose is available on an indent only basis

HYDRAULIC HOSES

37AL

NON-CONDUCTIVE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

ANSI A92.2 for Vehicle Mounted Aerial Devices

polyester core tube

voltage sources.

SAE J517 Non-conductive hose

Aerial equipment

Construction

Mobile hydraulics

SAE 100R7

Rescue apparatus and tools

THERMOPLASTIC HOSE

Reinforcement:

Temperature Range:

Features:

braided synthetic fibre

-54°C up to +100°C

SAE J517 non conductive hose construction.

except max. 60°C with water based or fire

Less than 50 microamperes leakage when

resistant fluids

subjected to 246062 volts/metre for 5 minutes. Flexible at low temperatures Abrasion resistant cover Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) at 133% WP

Cover:

Comment:

orange non-perforated non stick polyurethane

Lay line example may not be a true indication

Pirtek ‘S7’ Series (refer Table for Die)

of current status. Refer Pirtek for current

Pirtek ‘T’ Series option

Hose Tails:

information Lay line example: Black text on orange hose. Note Comment above

SYNFLEX® 37AL-04 NON-CONDUCTIVE SAE 100R7 1/4” I.D. 2750 PSI W.P. (190 BAR) ANSI A92-2 3000 PSI W.P. (207 BAR). USE DIE 4540-3W400

Product Code 37AL-03 †

Nominal ID DN 5

mm 3/16

OD in 4.8

working 207

min burst 827

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 19

Kg/100m 7.1

Die 4540303

Series S7

37AL-04

1/4

6.4

12.3

207

759

8.9

3W4

37AL-05 †

5/16

7.9

14.7

207

689

11.2

305

37AL-06

3/8

9.5

16.1

207

620

14.1

306

1/2

12.7

20.7

207

620

21.3

308

37AL-08 † Non-standard product. Available to special order

mm 10.8

Pressure bar

TWIN-LINE NON-CONDUCTIVE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

ANSI A92.2 for Vehicle Mounted Aerial Devices

polyester core tube

voltage sources.

SAE J517 Non-conductive hose

Aerial equipment

Construction

Mobile hydraulics

SAE 100R7

Rescue apparatus and tools Temperature Range:

Features:

braided synthetic fibre

-54°C up to +100°C

SAE J517 non conductive hose construction.

except max. 60°C with water based or fire

Less than 50 microamperes leakage when

resistant fluids

subjected to 246062 volts/metre for 5 minutes. Flexible at low temperatures Abrasion resistant cover Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) at 133% WP

Cover:

Comment:

orange non-perforated non stick polyurethane

Lay line example may not be a true indication

Pirtek ‘S7’ Series (refer Table for Die)

of current status. Refer Pirtek for current

Pirtek ‘T’ Series option

Hose Tails:

information Lay line example: Black text on orange hose. Note Comment above

THERMOPLASTIC HOSE

Reinforcement:

HYDRAULIC HOSES

37ALX2

SYNFLEX® 37AL-04 NON-CONDUCTIVE SAE 100R7 1/4” I.D. 2750 PSI W.P. (190 BAR) ANSI A92-2 3000 PSI W.P. (207 BAR). USE DIE 4540-3W400

Product Code

Nominal ID

37ALX2-04

DN 6

mm 1/4

37ALX2-06

3/8

37ALX2-08

1/2

OD in 6.4

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 12.3

working 207

min burst 759

mm 32

Kg/100m 17.8

Die 45403W4

Series S7

9.5

16.1

207

620

28.2

306

12.7

20.7

207

620

42.6

308

HYDRAULIC HOSES

3800

HIGH PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems

SAE 100 R8

nylon core tube

High pressure gas and chemical transfer Machine tools Mobile equipment Marine steering

Reinforcement:

Temperature Range:

Impulse Testing:

braided high tensile aramid fibre (Kevlar)

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only)

THERMOPLASTIC HOSE

Cover:

Comment:

black perforated non stick polyurethane

Lay line example may not be a true indication

Hose Tails: Pirtek ‘S7’ Series (refer Table for Die)

of current status. Refer Pirtek for current information

Lay line example: White text on black hose. Note Comment above

SYNFLEX® 3800-04 SAE 100R81/4” W.P 5000 P.S.I. (345 BAR) SAINT-GOBAIN

Product Code

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 38

Kg/100m 8.3

Die 4540303

Series S7

DN 5

mm 3/16

in 4.8

mm 11.0

working 345

min burst 1379

3800-04

1/4

6.4

13.5

345

1379

11.8

304

3800-06

3/8

9.5

16.9

276

1103

15.8

306

3800-08

1/2

12.7

21.3

241

965

102

21.7

308

3800X2-04

1/4

6.4

13.5

345

1379

23.6

304

3800X2-06

3/8

9.5

16.9

276

1103

31.6

306

3800X2-08

1/2

12.7

21.3

241

965

102

43.4

308

3800-03

Nominal ID

HYDRAULIC HOSES

3E80

NON-CONDUCTIVE HIGH PRESSURE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

SAE 100 R8

smooth seamless nylon

voltage sources.

SAE J517 non-conductive construction

Aerial equipment. Mobile hydraulics. Rescue apparatus and tools Reinforcement:

Temperature Range:

Features:

braided synthetic fibre

-40°C up to +100°C

SAE J517 non conductive hose construction.

Max 66°C with water-based or fire resistant fluids Less than 50 microamperes leakage when Impulse Testing: Hoses are tested to withstand 200 000 impulse cycles (hose only) Cover:

Comment:

Orange non stick non-perforated polyurethane

Lay line example may not be a true indication

Hose Tails: Pirtek ‘S8’ Series (refer Table for Die)

of current status. Refer Pirtek for current information Lay line example: Black text on orange hose. Note Comment above

SYNFLEX® 3E80-06 SAE 100R8 3/8” W.P 4000 P.S.I. (276 BAR) NON CONDUCTIVE FURON

Product Code

Nominal ID

3E80-04

DN 6

mm 1/4

3E80-06

3E80-08

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 51

Kg/100m 17.6

Die 4540H04

Series S8

in 6.4

mm 15.9

working 345

min burst 1379

3/8

9.5

19.5

276

1103

22.0

H06

1/2

12.7

22.7

241

965

102

28.3

H08

THERMOPLASTIC HOSE

subjected to 246000 volts/metre for 5 minutes

HYDRAULIC HOSES

3R80

HIGH PRESSURE HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems

SAE 100 R8

smooth seamless nylon

High pressure pneumatic systems Machine tools Mobile equipment Mobile hydraulics

Reinforcement:

Temperature Range:

Impulse Testing:

braided synthetic fibre

-40°C up to +100°C

Hoses are tested to withstand 200 000 impulse

Max 66°C with water-based or fire resistant fluids cycles (hose only)

THERMOPLASTIC HOSE

Cover:

Comment:

black perforated non stick polyurethane

Lay line example may not be a true indication information

Lay line example: White text on black hose. Note Comment above

SYNFLEX® 3R80-08 SAE 100R8 1/2” W.P 3500 P.S.I. (241 BAR) SAINT GOBAIN

Nominal ID

Pressure bar

Min bend radius

Weight

Synflex Die and Hose Tail Combination

mm 38

Kg/100m 11.5

Die 4540H03

DN 5

mm 3/16

in 4.8

mm 13.1

working 345

min burst 1379

3R80-04

1/4

6.4

15.9

345

1379

17.6

H04

3R80-06

3/8

9.5

19.5

276

1103

22.0

H06

3R80-08

1/2

12.7

22.7

241

965

102

28.3

H08

3R80-12

3/4

19.1

28.9

155

620

165

38.1

H12

3R80-16

25.4

37.4

138

552

254

57.3

H016

3R80-03

Pirtek ‘S8’ Series (refer Table for Die)

of current status. Refer Pirtek for current

Product Code

Hose Tails:

Series S8

NON-CONDUCTIVE JACKING HOSE

Construction

Applications

Reference Specifications

Inner Tube:

General hydraulic systems that may contact high

Meets SAE 100 R8

smooth seamless nylon

voltage sources.

SAE J517 Non-Conductive Hose Construction

Aerial equipment. Mobile hydraulics. Rescue apparatus and tools. Reinforcement:

Temperature Range:

Features:

spiralled high tensile aramid fibre (Kevlar)

-40°C up to +66°C

High WP 8000—10000 psi (551–689 bar)

HYDRAULIC HOSES

3VEO

Compact size with low elongation subjected to 246000 volts/metre for 5 minutes. Cover:

Comment:

Hose Tails:

Orange non stick non-perforated

Lay line example may not be a true indication

Pirtek ‘SV’ Series

polyurethane. (See note)

of current status. Refer Pirtek for current

Special procedures apply. Assemblies only to be

information

made by trained personnel listed on the Qualified Personnel Register Guards and warning tags are required on the completed assembly

Lay line example: White text on orange hose. Note Comment above

THERMOPLASTIC HOSE

Less than 50 microamperes leakage when

SYNFLEX® 3VEO-04 SAE 1/4” I.D. W.P 10,000 P.S.I. (690 BAR) (NON CONDUCTIVE) PAT. NO. 4343333

Product Code

Nominal ID

Pressure bar

Min bend radius

Weight

working

min burst

Kg/m

3VEO-04

6.3

1/4

14.0

689

2758

0.158

3VEO-06

9.5

3/8

17.4

551

2205

0.244

3VEO hose assemblies are available only as completed assemblies from accredited assemblers. Each assembly comprises : 3VEOhose Pirtek SV Series couplings Hose guard Identity Tag 3VE0-04 assemblies complete with 3/8” NPT male ends are available in 3 standard configurations. Other configurations upon request 3VEO04-06-2 3VEO04-06-4 3VEO04-06-6

2 meters long 4 meters long 6 meters long

HYDRAULIC HOSES

STH

PTFE (TEFLON) HOSE

Construction

Applications

Reference Specifications

Inner Tube:

Medium pressure and laundry equipment

SAE 100 R14

extruded seamless smooth bore Teflon

Plastic moulding presses Hazardous chemicals Steam and compressor discharge

Reinforcement:

Temperature Range:

Features: A graphite impregnated (black)

AISI 304 stainless steel single wire braid

-54°C up to +230°C (see graph below)

Teflon liner is available to special order for applications requiring a core tube capable of safely conducting static electricity. Consult Pirtek

THERMOPLASTIC HOSE

for details Impulse Testing: No information available Cover:

Comment:

The reinforcement braid serves as the outer

No lay line present due to the stainless steel

cover

braid

Product Code

Nominal ID

Hose Tails:

Average OD

Wall Thickness

Pirtek ‘T’ Series

Pressure bar

Min bend radius

Vacuum Service *

STH-03

Braiding 1 Braid

mm 4.8

in 3/16

mm 7.6

mm 1.4

working 206

min burst 828

mm 50

bar 0.9

STH-04

1 Braid

6.35

1/4

9.5

1.57

206

828

0.9

STH-05

1 Braid

7.94

5/16

10.9

1.48

172

692

100

0.9

STH-06

1 Braid

9.5

3/8

12.8

1.65

138

552

125

0.9

STH-08

1 Braid

12.7

1/2

16.3

1.80

120

484

165

0.9

STH-10

1 Braid

15.9

5/8

19.2

1.65

103

416

187

0.9

STH-12

1 Braid

19.05

3/4

22.6

1.78

276

212

0.4

STH-16

2 Braid

25.4

30.9

2.75

276

225

0.4

* Use of an internal support coil for hoses -06 and larger for tube support where continuous or extended service at high temperature together with low or negative pressure is expected † Non-standard product. Available to special order

Not recommended for steam / cold water recycling

Above 120°C Pressure: Reduce working pressure by 1% per additional degree C. Vacuum: Reduce vacuum rating by 1.5% per additional degree C. Note: The minimum bend radius quoted is for a static bend at ambient temperature. Dynamic bending, especially at elevated temperatures, will increase the minimum bend radius accordingly. Consult Pirtek for specific applications

HYDRAULIC HOSES THERMOPLASTIC HOSE This page is part of a complete catalogue containing technical and safety data. All data must be reviewed when selecting a product. Pirtek reserve the right to change technical specifications without notice Rev 4

SUMMARY OF PIRTEK HYDRAULIC HOSE MATERIALS Product Code

Liner Material

Cover Material

NBR (Class I)

C21

210 bar four spiral hose

NBR (Class I)

C25

250 bar four spiral hose

NBR (Class I)

C35

350 bar braid or spiral hose

NBR (Class I)

C42

420 bar braid or spiral hose

NBR (Class I)

C45

450 bar spiral hose high flexibility

NBR (Class I)

HTAB / HTFH

Engine & air brake hose

NBR (Class I)

IRFAW

FRAS rated Air / Water Stone Hose

NBR (Class I)

IRFWSDH

FRAS Air Water Suction & Delivery

NBR (Class I)

IROFSD

Oil suction hose

NBR (Class I)

SBR

JBF

Large bore four spiral hose

NBR (Class I)

JH70

Jacking Hose

NBR (Class I)

JW210

210 bar jet wash hose

NBR (Class IV)

JW250

250 bar jet wash hose

NBR (Class IV)

400 bar jet wash hose

NBR Class IV)

JW400

RUBBER

TECHNICAL DATA

Two wire braid hose

Liquid Petroleum Approved Hose

Teflon

NBR (Class I)

Multi purpose oil and air hose

NBR (Class I)

High abrasion resistance 250 bar hose

NBR (Class I)

PC28PS

High abrasion resistance 280 bar hose

NBR (Class I)

PC35

High abrasion resistance 350 bar hose

NBR (Class I)

PC42

High abrasion resistance 420 bar hose

NBR (Class I)

R1AT

One wire braid hose

NBR (Class I)

R1ATFS

One wire fire suppression hose

NBR (Class I)

R2AT

Two wire braid hose

NBR (Class I)

R2ATHT

High Temp. two wire braid hose

NBR (Class IV)

R5HT

High Temp. Air Brake Hose

NBR (Class IV)

Polyester

Low pressure hydraulic hose

NBR (Class I)

R12C

SAE 100R12 spiral hose

NBR (Class II)

R13C

SAE 100R13 spiral hose

NBR (Class II)

WB1000

1000 bar water blast hose

NBR (Class III)

WB1100

1100 bar water blast hose

NBR (Class III)

3130

General purpose SAE 100R7

Nylon

Polyurethane

3800

Compact SAE 100R8

Nylon

Polyurethane

High pressure non-conductive

Nylon

Polyurethane

Cold temperature hose

Polyester (Hytrel)

Similar to 3130

Nylon

Polyurethane

High flexibility forklift twinline

Nylon

Polyester (Hytrel)

Non conductive SAE 100R7

Polyester

Polyurethane

Jetting hose based on 3130

Nylon

Polyurethane

General purpose SAE 100R8

Nylon

Polyurethane

3VEO

Non conductive jacking hose

Nylon

Polyurethane

STH

Stainless steel braid over Teflon速

Teflon速

Stainless steel

LPG MPH PC25

30CT 31BO 3360X2 37AL 3JET 3R80

Description

2SC

3E80

Type

THERMOPLASTIC

HYDRAULIC HOSES

TECHNICAL DATA

CHEMICAL RESISTANCE TABLE CAUTION The data in the following pages has been compiled from generally available sources and should not be relied upon without consulting and following the specific recommendations of the manufacturers of particular products The data is considered valid at 20°C (70°F) except where specified otherwise. Chemical compatibility can vary greatly with temperature A good rating does not necessarily indicate the suitability of a particular hose and chemical combination due to variables such as improper clamp and coupling application, special hose construction, gasket material etc. Nor does it imply compliance with relevant food standards or safety standards that may be applicable

HYDRAULIC HOSES

TECHNICAL DATA

SOLVENT INFORMATION

Common Elastomers

ASTM Designation

Composition

General Properties

brominated butyl chlorinated butyl

BIIR CIIR

bromo isobutene-isoprene chloro isobutene-isoprene

excellent weathering resistance, low permeability to air and gases, good physical properties, resistant to heat poor resistance to petroleum based fluids, good resistance to fat

chlorinated polyethylene

CM (CPE)

chloro polyethylene

excellent ozone and weathering resistance, good oil and chemical resistance, excellent flame resistance

cross-linked polyethylene

XLPE UHMWPE

polyethylene and cross linking agent

excellent for a very wide range of solvents, chemicals, acids and oils

ethylene propylene

EPDM

ethylene propylene diene-terpolymer

excellent ozone, chemical and ageing resistance, poor resistance to petroleum based fluids, very good steam resistance

ethylene propylene

EPM (EPR)

ethylene propylene copolymer

excellent ozone, weathering, heat, chemical and aging resistance, poor resistance to petroleum products, very good steam resistance

hypalon ®

CSM

chloro-sulfonylpolyethylene

excellent weathering, ozone and acid resistance, good heat and abrasion resistance, fair resistance to petroleum based fluids

natural

isoprene natural

excellent physical properties, very good abrasion resistance, poor resistance to petroleum based fluids

neoprene

chloroprene

good weathering and flame retardant resistance, good oil reistance, good physical properties

nitrile (buna-n)

NBR

Acrylonitrile-butadiene

excellent petroleum products resistance, moderate resistance to aromatics, good physical properties

buna-n / PVC / NBR polyvinyl chloride

acrylonitrile-butadiene / polyvinyl-chloride

excellent petroleum products and weathering resistance, both for tube and cover

polyacrylic

ACM

acrylic monomer

excellent oil and tar resistance at high temperatures

sbr

SBR

styrene butadiene

good physical properties, good abrasion resistance, poor resistance to petroleum based fluids

viton ®

FKM

fluorocarbon rubber

excellent high temperature resistance, particularly in air and oil, very good chemical resistance This page is part of a complete catalogue containing technical and safety data. All data must be reviewed when selecting a product. Pirtek reserve the right to change technical specifications without notice Rev 4.1

TECHNICAL DATA

Aromatic solvents: benzene, cumene, p-cumene, naphthalene, toluene, xylene, cresol, styrene, cyclohexane and combinations Aliphatic solvents: propane, butane, pentane, hexane, heptane, dipetene, tripropylene Halogenous solvents: chloroform, dichorobenzene, dichloroethylene, methylen bromide, methylen chloride, benzyl chloride, carbon tetrachloride, trichloroethylene, carbon disulphite, turpentine, perchloroethylene, dichloroethane Ketonic solvents: acetone, methyl ketone, isobutyl ketone, methyl ethyl ketone, methyl isobutyl ketone Esters solvents: butyl acetate, methyl acetate, anyl acetate, isobutyl acetate Amines: aniline, ethylene diamine , diethanol amine, triethanolamine, dimethyl amine, monoethanolamine Alcohols: methanol, ethanol, propanol, butanol, glycerol

U G -

G -

C U U U

U G

C U C G C G U U U C U U U G U U C U C G C C U G -

C U G -

PVC

U C U G C C

G G G G G U G U G G G U G C G G C U G G

Polyurethane

U U

G C U G U G G G C G U G G C C G G G G -

U U C U C C C U U U C U C G U -

Polyester

G C U G U C C C C G U G G C C G G G G -

U G G C C G G U G U G -

Nylon

C C U U U

G G U G U U G U G G G G G G C G G G G G G G G -

Barium Salts Barium Sulphate Barium Sulphide Basic Copper Arsenate Beer Beet Sugar Liquors Benzaldehyde Benzene (Benzol) Benzenesulphonic Acid Benzine Benzine (Petroleum Ether) Benzine (Petroleum Naphtha) Benzoic Acid Benzyl Alcohol Benzyl Benzoate Benzyl Chloride Biodiesel < 92c Biodiesel > 92c Bismuth Carbonate Black Sulphate Liquor Blast Furnace Gas Borac Acid Borax Bordeaux Mixture Boric Acid Boric Copper Sulphate Brake Oil, Dot 3 Brake Oil, Dot 4 Brake Oil, Dot 5 Brine Bromine Bunker Oil ButAdiene Butane Butter Oil Butyl Acetate Butyl Alchol (Butanol) Butyl Amine Butyl Carbitol Butyl Cellosolve Butyl Mercaptan Butyl Stearate Butylene (Butene) Butyraldehyde Butyric Acid Calcium Acetate 10% Aq Calcium Arsenate Calcium Bisulphate 10% Aq Calcium Bisulphide Calcium Bisulphite Calcium Carbonate Calcium Chlorate Calcium Chloride 10% Aq Calcium Hydroxide 10% Aq Calcium Hypochlorite 10% Aq Calcium Nitrate 10% Aq Calcium Salts Calcium Silicate Calcium Sulphate Calcium Sulphide

Teflon

C G G

U G U U U U -

Class V

U U U U U C C

U G G G U

G C C U U U G

Class IV

U C C U C

U G G C G U

G C C C U U G

THERMOPLASTIC

Class III

G U

U U U

G C C G U U G

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class II

C C C C C C C

G G G G G G G G G G G G G G G G G G G G G G G G G G G C G G G G G G G G G G G G G G G G G G G

AGENT

Class I

C C

PVC

U C C C

Polyurethane

Polyester

U U U

Nylon

G G C C U C G G C G G U U C -

Teflon

Class V

Acetaldehyde Acetic Acid, Glacial Acetic Acid, Less Than 10% Acetic Acid, Over 10% Acetic Anhydride Acetone Acetophenone Acetyl Acetone Acetyl Bromide Acetyl Chloride Acetylene Acrylonitrile Air (Under 20kgf/Cm2) Alcohols Aluminium Aluminium Acetate Aluminium Bromide Aluminium Chloride Aluminium Fluoride 20% Aluminium Hydroxide Aluminium Nitrate 10% Aqueous Aluminium Salts Aluminium Sulphate Aluminium Sulphate Alums Ammonia Gas, Cold Ammonia Gas, Hot Ammonia, Aq Ammonia, Liquid (Anhydrous) Ammonium Carbonate Ammonium Chloride Ammonium Hydroxide Ammonium Metaphosphate Ammonium Nitrate Ammonium Nitrite Ammonium Phosphate Ammonium Sulphate Ammonium Thiocyanate Amyl Acetate Amyl Alchol Amyl Chloride Amyl Chloronapthalene Amyl Napthalene Anethole Aniline Aniline Dyes Aniline Hydrochloride Animal Oils Antirnony Salts Apoclor Monsanto (Chlorinated Hydrocarbon) Aqua Regia Aromatic Hydrocarbons Arsenic Acid Arsenic Salts Askarel Asphalt <105 C Auto Transmission Fluid Barium Carbonate Barium Chloride Barium Hydroxide

THERMOPLASTIC

Class IV

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class III

AGENT

Class II

TECHNICAL DATA B

CHEMICAL RESISTANCE TABLE

Class I

HYDRAULIC HOSES 50

TECHNICAL DATA

G G G G C C G G G G G G G G G G G G C C G G G G G G G G G G

G G G G G C G G G G G G U G G G G G G G G G -

G G G C U C G G G G U G C G G G G C C G -

G G U U G C C G G G C G U G G C G G G G -

G G G G G G G G G G G G G G G G

CHEMICAL RESISTANCE TABLE

U U C C U U G U U -

G G C C U G

C C G

U G U U U U G G G G -

C U G U G G U -

PVC

G U G G G -

Polyurethane

C C C

Polyester

C G

Nylon

G G G G G G G G G G G G G G G G G G G G G G G G G G U G G G G G G G G G G G G

Decalin Denatured Alcohol Detergent / Water Solution (Conc) Diacetone Diacetone Alcohol Diammonium Phosphate Dibenzyl Ether Dibutyl Ether Dibutyl Phthalate Dibutyl Sebacate Dichlorobenzene Diesel Fuel Oils Diesel Oil Light Diethanolamine (20% Conc.) Diethyl Ether Diethyl Phthalate Diethyl Sebacate Diethylamine Diethylene Glycol Di-Isobutylene Di-Isopropyl Ketone Dimethyl Aniline Dimethyl Formamide Dimethyl Phthalate Dioctyl Phosphate Dioctyl Phthalate (Dop) Dioxane Dipentene Dowtherm A and E Enamels Essential Oils Ethanol Ethanolamine Ether Ethyl Acetate Ethyl Acetoacetate Ethyl Acrylate Ethyl Alchol (Ethanol) Ethyl Benzene Ethyl Cellulose Ethyl Chloride Ethyl Ether Ethyl Mercaptan Ethyl Pentochlorobenzene Ethyl Silicate Ethylene Cellulose Ethylene ChlorhydrIn Ethylene Chloride Ethylene Diamine Ethylene Dichloride Ethylene Glycol Ethylene Oxide Fatty Acid Ferric Chloride Ferric Chloride Ferric Nitrate Ferric Nitrate 10% Aq Ferric Sulphate 10% Aq Ferrous Chloride Ferrous Nitrate

Teflon

U U U G C G G G C G C U U C U C G U U C G G G G G G G G C C C G G U -

Class V

U C C G U C C C C C C U U G U U C U U U G G C G G G G G U U U G C G G -

Class IV

G G G G G -

U C C G U C C C C C C U U G U U U U U U G G C G G G G G U U U C C G G -

THERMOPLASTIC

Class III

G C C -

U G G G G G G G C G C G G G G U C U G U G G G G C G G G U U U G C G G -

Class II

U U G U G

U G -

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class I

U G U C U U U G U C U U U U U U C U U G G U U -

PVC

G U C G G U U

Polyurethane

C U G U G U U G U C U U U U U U

Polyester

Class V

Nylon

Class IV

G -

Teflon

Class III

G U C U C U U U U G G C C -

AGENT

G G G G G G G G G G G G

G G G G G G G G G G G G G G G G U G G G G C G -

C C C G C C C C G G C C C C U U U G C G G -

C U C G C C C C G G C C C C U U U C C G G -

U G C C U U G G C C U C U U U G G G G -

G G G G G U G G U G G G G G G G G G G G G G G G G G G G G G G G G G G G

TECHNICAL DATA

Caliche Liquors (Chile Saltpetre) Cane Sugar Liquors Carbitol Carbolic Acid (Phenol) Carbon Bisulfide Carbon Dioxide Carbon Disulphide Carbon Monoxide Carbon Tetrachloride Carbonates Carbonic Acid Castor Oil Caustic Potash (<20%) Caustic Potash (>20%) Caustic Soda (Sodium Hydroxide) <20% Caustic Soda (Sodium Hydroxide) >20% Cellosolve Acetate Cellosolve Butyl Cellulubes Celanese (Phosphate Ester Base) Cellusolves Union Carbide China Wood Oil (Tung) Chlordane Chlorinated Solvents Chlorine Gas, Dry Chlorine Gas, Wet (<20%) Chlorine Trifluoride Chloroacetic Acid Chloroacetone Chlorobenzene Chlorobromomethane Chloroform Chloronapthalene Chlorosulphonic Acid Chlorotoluene Chromic Acid 30% Chromium Salts Cider Citric Acid Coal Gas Cod Liver Oil Coke Oven Gas Compressed Air (< 290 Psi or 2000 Kpa) Copper Chloride Copper Chloride 10% Aq Copper Cyanide 10% Aq Copper Sulphate 10% Aq Corn Oil Corn Syrup Cottonseed Oil Creosote Oil Cresol Cresylic Acid Crude Petroleum Oil Crude Wax Cupric Sulphate Cutting Oil White & Bagley No. 2190 Cyclohexane Cyclohexanol Cyclohexanone Cymene

THERMOPLASTIC

Class II

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class I

AGENT

HYDRAULIC HOSES

TECHNICAL DATA

Polyester

Polyurethane

PVC

G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G

Nylon

G G G G G

Hydrogen Peroxide, Dilute Hydrogen Sulphate, Gaseous Hydrogen Sulphide, Dry Hydrogen Sulphide, Wet Hydrogluosilic Acid Hydrolube Union Carbide (Hydraulic Fluid Water Glycol Base) Irus Shell 902 Hydraulic Fluid (Water-Oil Emulsion) Iso Octane Isobutyl Alcohol IsocyanAtes Isopropyl Acetate Isopropyl Alcohol Isopropyl Ether Jp-4, Jp-5 Kerosene Ketones Lacquer Lacquer Solvents Lactic Acid Lard Lead Acetate Lead Arsenate Lead Sulphate Lead Tetramethyl Light Oil Lime Lime Sulphur Linoleic Acid Linseed Cake Linseed Oil Linseed Oil Liquefied Petroleum Gas (LPG) Lubricating Oils, Diester Base Lubricating Oils, Petro Base Magnesium Chloride 10%Aq Magnesium Hydroxide 10%Aq Magnesium Sulphate 10%Aq Maleic Acid Mercuric Chloride Mercury Mesityl Oxide Methane Methy Salicylate Methyl Acetate Methyl Alcohol (Methanol) Methyl Bromide Methyl Chloride Methyl Ethyl Ketone (MEK) Methyl Formate Methyl Isopropyl Ketone Methyl Methacrylate Methyl Sulphate Methylene Chloride Methylisobutylketone (MIBK) MIL-H-46170 MIL-H-5606 MIL-H-6083 MIL-H-83282

Teflon

U C C

C C C G C C G C C G G G C C C G G G G G G C C C U U U G G G G C G C

Class V

G C U G G G G U G G G G U U U U G G C

C G G G G G

U U U C U C G G G G C G G G G G G G G G C G G G C G C G G C U G U

Class IV

U C U

G U C C G G U

U U C U C G G G G C G C G G G G G G G G G G G G C G C C G U U G U

THERMOPLASTIC

Class III

C C G G -

U G U G G G G G G G G G G G G G G G G G G G G G G G G G G U U G U

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class II

G U U U G U G -

C C U G G G G C U G G U G U G C G C U U C

AGENT

Class I

U G

PVC

U C

Polyurethane

Polyester

U U U C -

Nylon

C G C C C C C G G

Teflon

Class V

Ferrous Salt Solutions Ferrous Sulphate Fluoboric Acid Fluoboric Acid Fluorine Fluorosilicic Formaldehyde Formic Acid Freon 12 (Refrigerant) Freon 13 (Refrigerant) Freon 22 (Refrigerant) Fruit Juices Fuel Oil Fuel Oil (Aromatic Gas) 100 Octane Fuel Oil (Aromatic Gas) 100 Octane Fumaric Acid Furan Furfuran Furfural Furfuryl Alcohol Galic Acid (< 20%) Gas (Natural) Gas Oil Gaseous Hydrogen Gasohol Gasoline Gasoline (Aromatic) Gasoline (Nor-Aromatic) Gelatine Glucose Glue (Depends On Type) Glycerine, Glycerol Glycol To Wc Grease,Petroleum Green Sulphate Liquor Heavy Water (D20) Helium Heptane Hexaldehyde Hexane Hexene Hexyl Alcohol Hydraulic Oil Phos. Ester Blend (MIL L-7808) Hydraulic Oil, Auto Transmission Fluid Hydraulic Oil, Chlorine Base Hydraulic Oil, Ester Blend Hydraulic Oil, Ordinary Petro Hydraulic Oil, Phosphate Ester (FR) Hydraulic Oil, Silicone Oil Hydraulic Oil, Sodium Silicate Base Hydraulic Oil, Water & Petrol Emulsion (FR) Hydraulic Oil, Water Glycol (85c) Hydraulic,Oil, Water & Oil Emulsion Hydrobromic Acid Hydrochloric Acid V% Hydrocyanic Acid Hydrofluoric Acid, Cold Hydrofluoric Acid, Hot Hydrofluorsilic Acid Hydrogen (Gaseous) Hydrogen Peroxide, Concentrated

THERMOPLASTIC

Class IV

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class III

AGENT

Class II

TECHNICAL DATA B

CHEMICAL RESISTANCE TABLE

Class I

HYDRAULIC HOSES 52

TECHNICAL DATA

C G -

U U U U

C U -

G -

G G G G -

G C -

G -

G G -

G U C G G G G G G G -

C U U U -

G G C G -

G G G G G G G G G G G G G

G G G G G G G G G G G G G G G G G G G G G G G G C G G G G -

G C G C C G G G G G G G G C G C G C G G G C C U U C G C -

U C U U G G G G G G G G G G G G C G U U U U U U U -

G G G U C G C G C U -

U U G C G G U U U G U G G G G G G G U U U C G G G G

G G U U -

G G G G G G G G G G G G G G G G G G -

CHEMICAL RESISTANCE TABLE

G U U C U G G G G G G C G G G G G C G G G G

G U

U G U U C G C U U U U U

C G U G G U U U U U

G C G G G C G U U U U

PVC

G G G G G G G G G G G G G G G G G G G G G G

G -

Polyurethane

G G -

G U G U U U U U U U U -

Polyester

G G G G G G G G G G G -

G U C G G C G G C G G G U

Nylon

G G G

Potassium Permanganate (5%. Conc.) Potassium Sulphate Propane Propyl Acetate Propyl Alcohol Pydraul (Stauffer) F-9,150, 600, 625 Pyrethrum Pyridine Red Oil Salt Water (Sea Water) Saturated Steam Sewage Silicone Oils Silver Nitrate Skydrol Monsanto 500, 7000 Soap Solutions Soda (Sodium Carbonate) Soda Water Sodium Acetate 10% Aq Sodium Bicarbonate 10% Aq Sodium Bisulfite Sodium Bisulphate Sodium Borate Sodium Carbonate Sodium Chloride Solutions Sodium Cyanide Sodium Hydroxide <10% Sodium Hydroxide 40% Sodium Hypochloride 10% Sodium Hypochlorite Sodium Metaphosphate 10% Aq Sodium Nitrate 10% Aq Sodium Perborate 10% Aq Sodium Peroxide 10% Aq Sodium Phosphates 10% Aq Sodium Silicate 10% Aq Sodium Sulphate 10% Aq Sodium Sulphide Sodium Sulphite 10% Aq Sodium Thiosulphate (Hypo) 10% Aq Solution 2-4D DDT Preparation Hydroxy Quinoline Soybean Oil Stannic Chloride Stannous Chloride Steam Steam Stearic Acid Stearic Acid, Botanical Stearin Stoddard Solvent Styrene Sucrose Solution Sulphur Sulphur Sulphur Chloride Sulphur Dioxide Sulphur Trioxide Sulphuric Acid, 10%, Hot Sulphuric Acid, 10%. Cold Sulphuric Acid, 75%, Cold

Teflon

G G G U U U G G G U G C G C G G C C G C C C G G C C G G G C G

Class V

G G G G C C G U C U G G G G C C G G C G G U U G C U G U U G U G

Class IV

G G G G C C U G U C U G G G G C C G G C G G U U G C U C U U G U G

Class III

U U U U G -

G G G G G G U G C C G G G G G G G G G G G G U G G G U C G C G C G

THERMOPLASTIC

Class II

U U C U G U -

G G

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class I

U U U U

PVC

G U G G U U U U U U U -

Polyurethane

G G G G U G U G G G U U U G U U C U C U G U U U U U U G G G G G -

Polyester

Class V

Nylon

Class IV

U C G U U U U U U U C U

Teflon

Class III

G C G U C G G G G -

AGENT

G G G G G G G

U G G G G C G G G G G G G G G G G C G G G G G G G C U G G G G G U C C -

U G G C G C G U G G G G G G G G C C G G G G G G G U G G U C G U U U -

U G G C G G G U G G G G G G G G C C G G G G G G G U C G U C G U U U -

G G G U G U G U G G C G G G G G G G G G G G G G G G U G C G C G G -

G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G

TECHNICAL DATA

Milk Mil-L-2104 Mil-L-23699 Mil-L-7808 Mineral Oils Molasses Monochlorobenzene Mustard Naphtalene Naphtha Napthenic Acid Natural Gas Nickel Acetate 10% Aq Nickel Chloride Nickel Sulphate Nicotine Nitric Acid (Conc) Nitric ACid (Dil) Nitriuc Acid (Red, Fuming) Nitrobenzene Nitrogen / Argon Gaseous Nitrous Oxide Octyl Alcohol Oil Oil Of Turpentine Oleic Acid Oleum Spirits Olive Oil Ortho-Dichlorobenzene OS 45 Monsanto Hyd. Fluid (Silicate Ester Base) Oxalic Acid Oxygen (Liquid) Oxygen Gaseous Ozone Paint (Oil Based) Paint Solvents (Oil Base) Palmlitic Acid Peanut Oil Pentane Perchloric Acid Perchloroethylene Petroleum Oils (Refined) Petroleum Oils (Sour) Phenol (Carbolic Acid) Phenolates Phenols (Carbolic Acid) Phosphate Ester Base Oil Phosphoric Acid (70%) Phosphoric Acid 10% Picric Acid (Molten) Picric Acid (Solution) Pine Oil Pinene Plating Solution, Chrome Potassium Acetate 10% Aq Potassium Chloride Potassium Cyanide Potassium Dichromate Potassium Hydroxide (Potash) Potassium Nitrate

THERMOPLASTIC

Class II

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class I

AGENT

HYDRAULIC HOSES

TECHNICAL DATA

G C G G U G G

G G U -

PVC

G G -

U U -

Polyurethane

G C C C

U U U G G G G U U U -

Polyester

U U U U U G U

Nylon

U G -

U U U

Teflon

U U U G G U U -

Class V

Sulphuric Acid, 75%, Hot Sulphuric Acid, 95%, Cold Sulphuric Acid, 95%, Hot Sulphurous Acid Tannic Acid Tar Tartaric Acid Terpineol Toluene Toluol Transformer Oil Transmission Fluid Type A Tributoxyethyl Phosphate Tributyl Phosphate Trichloracetic Acid Trichlorethylene Tricresyl Phosphate Trisodium Phosphate Solution Tung Oil (China Wood Oil) Turpentine Oil Ucon Union Carbide (Hydraulic Fluid Water Glycol Base) Urea Uric Acid Varnish Vegetable Greases Versilube Vinegar Vinyl Chloride Water @ 65째C Water Glycol Water, Normal Temp Whiskey White & Bagley No. 2190 Cutting Oil Wine Wool Oil Xylene Xylol Zinc Acetate Zinc Chloride 10% Aq Zinc Hydrate Zinc Sulphate 10% Aq

THERMOPLASTIC

Class IV

Legend: G = Good C = Conditional U = Unsatisfactory No Data

RUBBER

Class III

AGENT

Class II

TECHNICAL DATA B

CHEMICAL RESISTANCE TABLE

Class I

HYDRAULIC HOSES 54

TECHNICAL DATA

G G G

G G G G G G G

U U G G G G G G U G G G G

U U C G G C C C U U C C G

U C G G G U U U C C U G G

G G G G G G G G G G G G G G

G G G G G G G G G G G G U U

C C U G C G G G C C G C C

G C U G C G G G C C G C C

G G G U G G G G U U G G G

G G G G G

HYDRAULIC HOSES

ALPHANUMERIC INDEX

Description

ALPHANUMERIC INDEX

3130

Page/s 38

Description High Pressure Non Conductive

Page/s 43

3800

High Pressure R8

PC28PS

3E80

High Pressure Thermoplastic

PC35

1 - Wire Braid

High Temp 2 Wire

PC42

2 - Wire Braid

High Temp R5

R1AT

2SC

HTAB / HTFH

R1ATFS

30CT

IRFAW

R2AT

30CTX2

IRFWSDH

R2ATHT

3360X2

IROFSD

R5HT

37AL

Isobaric Hoses

20 - 28

37ALX2

Jacking Hose

19, 45

3R80

JBF

Description PC25

Page/s 25

R8 hose

R12C Spiral Hose

12 - 14

R13C Spiral Hose

Safety Warning

1 2-3

3VEO

Jet Wash

Broad Spectrum Hose

JH70

C21

JW210A

Selection Guide

C25

JW250 / 250A

Stainless Teflon Hose

C35

JW400 / 400A

STH

C42

Large Bore Hose

Thermoplastic Hoses

C45

Low Pressure Oil Hose

Truck Hose

Compact R8

MPH

Twinline 30CT

Fast Find Table

Multi Purpose Hose

Twinline Non Conductive

Fire Suppression Hose

Non Conductive Hose

Waterblast Hoses

Forklift Twinline

Non Conductive Jacking

WB1000

WB1100

FRAS Air Water Hose

Oil Suction Hose

FRAS Air Water Suction

Ordering Assemblies

7 46 35 - 46 10

33 - 34

Chemical Compatibility Tables Commence page 48