BAYTOM
installation, user and maintenance manual
TABLE OF CONTENTS 1. FIRST INSTALLATION ………………………………………………………..3 1.1SMS and Warning System Installation ………………………...3 1.2 Gift Mechanism Installation...………...........………….………..5 2. What to do maintenance and schedules ...….……………………………6 3. THE USE OF THE DEVICE ....……….……………………….………………9
1- FIRST INSTALLATION Please set up the SMS alert system and gift mechanism firstly when preparing to use after unpacking the machine
1.1 SMS alert system set up: -Please insert the sim card which to be used for SMS system into any mobile phone -record the authorized person number under ww name ( for informs by sending SMS when it runs out of gift money, filling of thanks or in the case of pouring harmful substances. Insert the sim card as shown below - Unpack the machine,open the cover as shown figure 1 by using the keys that came with device , insert the sim card GSM-GPRS modem slot as shown in figure 2, Open the hatch shown in
Figure1
Figure2
Plug the power cord into a wall outlet "220 Volt grounded" Open the front cover of the machine (Figure 4).Turn on the switch by pressing and holding the button. After switch on, press and hold the button for 3-5 seconds and release it. Thus, lights up and wait at the front of the device is highlighted for a while and then ready light is came on.
- Plug the power cord into a wall outlet "220 Volt grounded" ( As in figure 3 switch must be closed ''OFF'' before power is connected to the device Figure3 Press and hold the button for 10-15 seconds and release it. - Open the front cover of the machine (Figure 4) Switch on the switch (figure 6) by pressing and holding the button at the bottom of the cover (as shown in figure 5)
Figure4
Figure5
Turn on switch by pressing and holding the button and hold the button for 10-15 seconds then wait.
Figure6 The authorized mobile will be receive ''Number detected'' SMS If the save operation was done correctly. After receiving this message the device is ready for the SMS system.
1.2 İnstallatio of the mechanism of gift. Open the front cover of the device to set-Gift mechanism. (Figure 4) - Put enough coins in the reservoir of coins as shown “figure7� and press the button once again at the bottom of the front cover .. (During this process the oil cap should be in the closed position ). Put enough gift coin hopper and press the indicated button once.
Figure7 Coins engine turns and loads of money into the mechanism. The mechanism is ready for use. Open the rear cover as shown figure 8,check and bu sure that ''oil" and "other liquid" tanks, fluid hoses and sensors are in the correct position as shown figure 9,Before using the machine, If have a wrong situation, correct it.
Open the shown cover for check inside.
Figure 8
bu sure that ''oil" and "other liquid" tanks, fluid hoses and sensors are in the correct position as shown
Figure9 After these settings are required, the device is ready for use. 2- What to do maintenance and schedules -. The measuring electrodes are cleaned with hot water, (so that once a month ) Remove the electrodes by unscrewing the screws and the cable disconnect on ground as shown on figure 10, clean it with warm water and refit. Pull the cable to the direction of the arrow and remove. Cable Remove electrodes by removing the two screws and the cable
- The first filling containers, clean it with warm water. ( Weekly ) Pour hot water into the hopper by opening the oil cap. hold on the cup until 10 minutes and then close it. liquid reservoir and inside the pipes are cleaned and discarded into the other liquid container. In case of spillage of harmful substances, the device locks itself, - Out of service light flashes and informs the competent person by SMS. Take the oil tank for cleaning. Instead of it place a container for dropping off foreign substances inside. While the device is running open the front cover by key press and hold the button shown in figure 5 and release it. Clean the appliance by pouring hot water. After the completion of the cleaning process Put the oil cap back in place. Remove and insert the plug of the device. Device is
ready to work. In case of filling ''oil or other liquid" containers the device locks itself and out of service status light is flashing and informs authorized person by ''Tank Full'' message. The person who will maintain the machine, ripped the containers as shown in figure 11 by opening the back cover, after evacuation of tanks, attached empty containers and close the lid.(Oil tanks capacity is about 58 lt. water tank is about 17 liters of liquid.) Remove the oil tank by upward bending the shoving sensor. Remove by opening the other liquid tank's cap.
Figure 11 The coin hopper is emptied, sends ''Promotion exhausted'' SMS to authorized person. The device allows the service. But it can not pay and notifies the user by voice. The authorized person, opens the front cover of the device and puts the coins into mechanism as shown in figure 12, and makes the mechanism available by pressing the button once. (Oil cap must be turned off during this process) Insert the coins into the mechanism as shown in
Figure 12 Clean with hot water by removing the ground oil filter, while unloading tanks or during an exchange with empty ones as shown in figure 13, Clean the filter by removing the displaced.
3- THE USE OF THE DEVICE Oil cover is opened, the waste oil is poured (maximum 2 liters) and the cover is closed.
to determine the nature and amount of liquid spilled, wait 10-15 seconds
Is taken a coin by the amount of spilled oil
Coins gift mechanism
Non-contact, magnetic card, point loading mechanism
Contactless magnetic card: After pouring oil into the machine, for loading the points, move the Baytom Card to the points loading mechanism on the machine. Thus, in the amount of oil spilled your card will be installed You can convert your points to cash or gifts to be determined by municipalities or licensed to oil collectors