AS65 Center Drive Conveyor Installation, Maintenance & Parts Manuals by QC Industries

Driven By Customers … Powered by Proven Products

Table of Contents Section I – General Warnings – General Safety Foreword Product Description Tools Required

1.01 1.02 1.03 1.04

Section II – Setup and Installation When Your Shipment Arrives Sequence of Installation / 13’ and Shorter Conveyors 13’ and Shorter Sequence of Installation / Longer than 13’ Conveyors Longer than 13’ Aluminum Exact Width Stands Angle Braces Aluminum Cross Ties Casters Side Mounts Fixed Side Rails Adjustable Guides Installing a Heavy Duty Motor

2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13

Section III – Maintenance Maintenance Foreword Belt Tracking Belt Change Adding Tension Belt Care Bearing Replacement Fastener Tightening Torque Specifications Conveyor Exploded View and Parts List Recommended Spare Parts Troubleshooting

3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10

Installation, Maintenance, and Parts Manual

4.01 4.02 4.03

Automation Series Conveyor

Section IV – Warranty and Return Policy Conveyor Serial Number Conveyor Warranty, Lost or Damaged Goods Returns, Order Cancellation/Revision Policy

Center Drive (AS65)

QC Industries LLC 4057 Clough Woods Dr. Batavia, OH 45103 (513) 753-6000 Fax: (513) 753-6001 www.qcindustries.com

ÂŠ Copyright 2009 QC Industries, LLC 4057 Clough Woods Drive, Batavia, OH 45103 (513) 753-6000, fax: (513) 753-6001 www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

1.01 Warnings â&#x20AC;&#x201C; General Safety

Observe safe practices when setting up and operating your QC Industries conveyor. Climbing, sitting, walking, or riding on conveyor can cause severe injury. Keep off conveyors. Do not operate conveyors in an explosive environment. Exposed moving parts can cause severe injury. Lock out power before removing guards or performing maintenance. Gearmotors may be hot. Do not touch gearmotors. QC Industries cannot control the installation and/or application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment, or as part of a multiple conveyor system, check for potential pinch points and/or other mechanical hazards before system start-up. During normal operation, please make sure that all guards are in place and securely attached to conveyor. Loosening stand height or angle adjustment screws can cause conveyor sections to drop down unexpectedly, causing severe injury. Support conveyor sections prior to loosening stand height or angle adjustment screws. Injury is possible if the stands are not lagged to the floor, cross ties are not used, or angle braces are not present. Never place a conveyor in operation until all proper mounts are installed and secured. It is the end userâ&#x20AC;&#x2122;s responsibility to ensure that the support system is safe and secure. Never operate equipment unless all operating instructions are understood and all guards, interlocks, covers, safety devices or circuits and protective components are functioning properly. Never operate or service this equipment if under the influence of alcohol, drugs or other substances or conditions which decrease alertness or judgment.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

1.02 Foreword Congratulations on purchasing a conveyor from QC Industries, LLC, the leader in low profile conveyors! QC Industries offers the finest low-profile conveyors available, using the highest quality materials and state of the art manufacturing processes. QC Industries conveyors boast a number of innovative engineering features to assure you of hassle-free setup, smooth operation, and years of continued low maintenance use. We are proud of our quality products and are committed to providing you dependable service!

Check your shipment Before opening the shipment, visually inspect the outside of the crate/box for shipping damage. Contact the carrier and QC Industries regarding any damage that may have occurred during shipment. If damage has occurred, do not discard the packaging, as most carriers will deny a claim if they cannot inspect the damaged packaging. Photos of damaged packaging prior to unpacking are also helpful when processing a claim with the carrier. Carefully unpack the crate/box, inspecting for component damage which may have occurred inside the packing materials. Check the contents of your shipment against the supplied packing slip and inform QC Industries of any discrepancies.

Please read this manual Inside this manual you will find instructions on how to set up and maintain your QC Industries conveyor properly, as well as maximize its performance. Please take the time to read this manual and familiarize yourself with these setup and maintenance instructions. These instructions will help assure a long product life that requires a minimum amount of service and keeps your conveyor working at its maximum capacity.

If you need assistance If you need assistance with your QC Industries conveyor, a highly trained support staff is only a phone call away. QC Industries welcomes the opportunity to assist you. You can contact the Customer Service department Monday through Friday, 8am-5pm EST at (513) 753-6000. In addition, your local distributor can provide support in many ways. Our distributors have been trained at the factory and can be dispatched to your facility to help. You can also visit our website for additional information and technical documents â&#x20AC;&#x201C; www.qcindustries.com

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

1.03 Product Description The Automation Series Conveyor has many typical conveyor components, as well as some new features exclusive to this product line. Below is a basic description of the parts and options for the Automation Series Conveyor (Figure 1).

Figure 1

Typical Components 1. 2. 3. 4. 5. 6. 7. 8. 9.

Conveyor Frame Fixed End Tension Release Tail Center Drive Assembly Underside Idler Gearmotor Exact Width Stand Outrigger Stand

10. 11. 12. 13. 14. 15. 16. 17.

Single Post T Stand Cross Ties Single Cross Tie Angle Brace Leveling Foot Caster Fixed Siderails Adjustable Guides

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

1.04 Tools Required Set of Metric Allen Wrenches: 3mm, 4mm, & 5mm key

A Bubble Level for frame alignment

Aluminum Cutting Hack Saw or equivalent Set of Metric Wrenches: 3mm - 12mm

Torque Wrenches: 5-50 in-lb range 5-50 ft-lb range

Tape Measure

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

T30 Torx Bit

2.01 When Your Shipment Arrives n Check your shipment for damage a. If you have not already done so, visually inspect the outside of the crate or boxes for shipping damage. If damage has occurred, take photos and do not discard the packaging; this will aid your damage claim with the carrier. b. Contact the carrier and QC Industries Customer Service Department (513-753-6000) regarding any damage that may have occurred during shipment. c. Carefully unpack the crate or box, inspecting the components for damage which may have occurred inside the packing materials. d. Check the contents of the shipment against the included packing slip and notify QC Industries of any discrepancies.

o Locate the items from your order a. Each conveyor will ship in its own custom built box. b. Drive Mounting Packages are assembled at the factory with the gearmotor attached for Standard Duty Electric and DC drives; for Heavy Duty Electric Drives, the right angle speed reducer will be assembled, but the motor will be in a separate box. c. Aluminum Exact Width Stands ship two to a box. d. Cross Ties will ship in a custom built box; with the mounting hardware included. e. Mounts are packaged, all within the box with the Drive Mounting Package. f. Sides and Guiderails will ship in a custom built box, with mounting brackets for guides and hardware included.

p Record the Conveyor’s Serial Number a. The conveyor’s serial number is located on the center drive package mounting plate, opposite the side on which the gearmotor will be mounted. b. Record the serial number in a place where it can be accessed for reference; a place has been provided on the back cover that can be used for multiple conveyors. This will assist any future inquires regarding the conveyor, its accessories, the order it was shipped on, or replacement parts. c. Proceed to Section 2.02 for the Sequence of Installation for Conveyors 10’ and Under, or Section 2.04 for the Sequence of Installation for Conveyors Longer than 10’.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.02 Sequence of Installation To set up the conveyor after receiving your shipment, QC Industries recommends that you follow these steps. Please refer to their respective sections for more detailed instructions.

n Move the Conveyor and Accessories into location Using appropriate equipment and safe moving methods, move the conveyor and accessories to the desired assembly, staging, or installation area (Figure 1). Set the conveyor in the correct operating orientation with regard to the drive position and belt direction. See Section 2.03 for detailed instructions

Figure 1

o Mount the Conveyor to its Stands and Cross Ties or Mounts Use QC Industries stands and mounts (or any compatible stands and hardware) to mount the conveyor in the desired location (Figure 2). Make sure the conveyor mounted on stands is on a flat, level surface. QC Industries recommends that stands with leveling feet are anchored to the floor. See Sections 2.06 â&#x20AC;&#x201C; 2.10 for detailed instructions Figure 2

p Install the Sides / Guides, and Underside Idlers It is recommended that Side and Guide Rail Assemblies are next in the sequence, as once the Gearmotor is in place they may be difficult to install properly. Install underside idlers, if necessary (Figure 3). See Sections 2.11 â&#x20AC;&#x201C; 2.12 for detailed instructions

q Install the Heavy Duty Drive Motor (optional equipment), and check Belt Tracking

Figure 3

AS65 conveyors come with a Standard Duty gearmotor completely assembled from the factory, as standard. If you have a Standard Duty gearmotor, you do not need to install the drive - proceed directly to the Belt Tracking section. If you have purchased an optional Heavy Duty Drive, the gearbox will be assembled to the conveyor, but the motor will need to be installed. Wire the motor using the appropriate diagrams of the motor style, voltage and phase you have purchased (Figure 4). QC Industries recommends that all wiring be completed by a certified electrician. Check Belt Tracking. See Sections 2.13 and 3.02 for detailed instructions

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Figure 4

2.03 Conveyors 13’ and Shorter n Orient the Conveyor based on the Drive Location a. Set the conveyor in its operating position, taking care to note its drive location. AS65 Conveyors ship with a left hand drive or right hand drive that is predetermined at the time of the order, and can be decoded in the conveyor's part number. The 13th digit in the part number will indicate the side the Center Drive Guard is protruding toward, from the point of reference at the discharge end of the conveyor. The 14th and 15th digits in the part number indicate whether the conveyor was tracked at the factory with the Fixed End or the Tension Release Tail at the discharge end of the conveyor. The following is an example of a 8” wide x 10’ long conveyor: AC61H08-120-LFE-MAE There are four combinations available for the AS65 Center Drive (Figure 1): LEF Left Hand Guard, Fixed End at Discharge REF Right Hand Guard, Fixed End at Discharge RFE Right Hand Guard, Tension Release Tail at Discharge LFE Left Hand Guard, Tension Release Tail at Discharge Left hand and right hand are defined as if you are standing at the discharge end of the conveyor. F

LEF

L E

REF

R RFE

LFE

Figure 1

b. Position the conveyor for operation, taking care to note that when other equipment is nearby, access is needed for the tail assy’s Socket Head Set Screws (Figure 2). This is important when tensioning and tracking the belt from the tail idler end.

Tail Adjustment Set Screws

Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.03 Conveyors 13’ and Shorter (continued) o Install Stands, Mounts, Sides, Guides, Drives and Mounting Packages a. Proceed to Sections 2.06 – 2.10 for instructions on installing Stands and Mounts. b. Proceed to Sections 2.11 – 2.12 for instructions on installing Sides or Guides. c. Proceed to Section 2.13 for instructions on installing Drive.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.04 Sequence of Installation for Conveyors Longer than 13’ To set up the conveyor after receiving your shipment, QC Industries recommends that you follow these steps. Please refer to their respective sections for more detailed instructions.

Figure 1

o Assemble the Conveyor and Mount it to its Stands and Cross Ties or Mounts Use QC Industries stands and mounts (or any compatible stands and hardware) to mount the conveyor in the desired location (Figure 2). Make sure the conveyor mounted on stands is on a flat, level surface. QC Industries recommends that stands with leveling feet are anchored to the floor. See Sections 2.06 – 2.10 for detailed instructions Figure 2

p Install the Sides / Guides, and Underside Idlers It is recommended that Side and Guide Rail Assemblies are next in the sequence, as once the Gearmotor is in place they may be difficult to install properly. Install underside idlers (Figure 3). See Sections 2.11 – 2.12 for detailed instructions

q Install the Heavy Duty Drive Motor (optional equipment), and check Belt Tracking

Figure 3

Figure 4

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13’ For Extended Automation Series Conveyors (i.e. longer than 13’), the conveyor frames will ship unassembled with the belt rolled up. The process for assembling the conveyor frame differs depending on the width of the conveyor. 2” wide through 12” wide conveyors offer a single piece extruded aluminum frame construction. 18” wide through 24” wide conveyors have a combination steel and extruded aluminum construction.

n Assemble the Conveyor Frame - For 2” – 12” Wide Conveyors a. The Drive Frame and Extension Frame will ship unassembled in separate boxes. Locate the Tie Bar Assy’s on the Drive Frame. Using a 3mm Allen Wrench, remove the five M6 Socket Head Screws to disassemble the Tie Bar from the Anchor Bar (Figure 1).

Anchor Bar

b. Turn the Drive Frame and Extension frame upside down, and slide the Anchor Bar into the frame’s T-Slot. Slide the frames together so they mate up to each other (Figure 2). Tie Bar

c. Position the Anchor Bar so that the center hole is centered over the seam of the frames. Position the Tie Bar so it engages into the T-Slot and the clamp faces the top of the conveyor. Insert the M6 Socket Head Screws through the holes of the Tie bar until it is engages in the Anchor Bar (Figure 3).

Remove Screws Figure 1

d. Proceed to step 3 to install the belt.

Extension Frame

Locate Center Screw on seam of frame sections

Drive Frame Insert Anchor Bar into T-Slot Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Figure 3

2.05 Conveyors Longer than 13’ (continued) o Assemble the Conveyor Frame – For 18” – 24” Wide Conveyors a. The Drive Frame and Extension Frame will ship unassembled in separate boxes. Turn the Drive Frame and Extension Frame upside down, and orient them together for assembly so that the sheet metal frames and aluminum extruded rails will mate up to each other (Figure 1).

These edges will mate together Extension Frame

b. Slide the Drive Frame together with the Extension Frame, so that the bent sheet metal pieces mate up to each other. The extruded aluminum T-Slot rails that extend past the end of the Extension Frame will mate up to the shorter extruded aluminum TSlot rails mounted to the Drive frame. The Tie Bars that are mounted to the inside edge of the Extension frame will be loose so that the Drive Frame sheet metal can slip between the aluminum rails and the tie bar on the extension frame (Figure 2). c. Locate the bag of M6 Torx Head screws that is included and labeled in the shipping container; there are two different lengths – 18mm and 25mm long. Six 25mm long screws (3 per side) fasten through the Tie Bars at the sheet metal splice. The remaining 18mm long screws are used to mount the extruded aluminum T-Slot on the Extension Frame to the sheet metal on the Drive Frame, following the same location and spacing as the existing screw pattern (staggered approximately every 12 inches). Ensure that the last hole in both ends of the sheet metal frame has a screw inserted. Tighten all frame assembly screws to a torque value of 7 ft-lbs. (Figure 3).

Drive Frame

These edges will mate together

Figure 1

Drive Frame

Tie Bars loosely fastened

Extension Frame Figure 2

Drive Frame

25mm Lg. Torx Head screws for Tie Bars

d. Proceed to step 3 to install the belt. 18mm Lg. Torx Head screws for sheet metal, following existing screw spacing

Extension Frame

Figure 3

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13â&#x20AC;&#x2122; (continued) p Install the Belt (Conveyors with and without Stands) a. Unwrap the belt from its packaging, and lay it next to the assembled frame. Check the underside (carcass) of the belt for a run direction notation. If the belt has a specific run direction requirement, there will be arrow(s) on the underside of the belt at the splice that note the run direction.

Support seam of frame during moving & handling

b. Turn the conveyor onto its side, taking caution to support the seam between frames. Ensure the Tension Release Tail Assy is disengaged (rotated in the unlocked position) (Figure 1). c. Loop the belt around the tail plates, then insert the Tail Pulley assembly into the tail plates with jacking screw hex keys facing out for adjustment. Starting at the Tail End, loop the belt around the conveyor towards the fixed idler end, threading it through the drive area (Figure 2). Figure 1 Tail Pulley Assy

Tension Release Assy

d. At the drive area, disengage the Center Drive Idlers by pulling them out of the Mounting Plate slots. Thread the belt through the drive area and wrap it around the drive pulley. Reinsert the Center Drive Idlers into the Mounting Plate slots and adjust them to the indicator marks (Figure 3). Figure 3

Figure 2

e. Finally, lock the Tension Release Tail Assembly into run position (Figure 4).

Rotate and lock into run position

f. Inspect the straightness of the belt in relation to frame. If the belt is not centered at the pulleys, disengage the Tension Release Tail assembly and readjust the belt so itâ&#x20AC;&#x2122;s centered. g. If your conveyor is to be mounted on QC Industries stands, proceed to step 4 to complete the stand/conveyor assembly. If your conveyor does not have stands, proceed to step 5 to tension the belt. Figure 4

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13â&#x20AC;&#x2122; (continued) q Mount the Stands to the Conveyor - For Conveyors with Frame Joint Stands a. Turn the conveyor upside-down onto its slider bed/belt, taking caution to support the seam between frames. b. Insert the stand base onto the stand brackets installed on the conveyor. First insert the Drop In Nuts into the extrusion channels, then align the Drop In Nuts to the slots on the stand brackets (Figure 1). c. Tighten the M6 Socket Head Screws in the Brackets with a 3mm Allen Wrench when the stand is in the approximate desired position. For most applications, this is when the extrusion touches the frame; for others, such as on cleated conveyors, the extrusion should be offset from the frame. d. Attach Aluminum Exact Width Stands to the Idler End and Drive End of the conveyor. Refer to Section 2.06 for specific instructions. e. Turn the conveyor over and set it onto its stands. It is recommended that at least three people are present to do so â&#x20AC;&#x201C; one at each end and one to support the joint. Take caution to support the seam between frames. Figure 1

f. Install Angle Braces or Cross Ties as instructed in Sections 2.07 and 2.08. g. Proceed to step 5 to tension the belt.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13’ (continued) r Tension the Belt a. Adjusting tension on Automation Series conveyors was designed to be very easy and user friendly. To set the initial tension, insert the Tail Pulley assembly into the disengaged (rotated in the unlocked position) Tension Release Tail Assy (Figure 1). b. Rotate the Tension Release Tail Assy, with Tail Pulley assembly inserted, down into the locked run position (Figure 2). Tension Release Tail Assy Tail Pulley Assy

Figure 2

Figure 1

Warning: The action of rotating the Tension Release Tail Assembly into position can pinch fingers! Keep hands and fingers away from the frame during engagement. Do not place hands or fingers between the frame and conveyor belt, or the tail pulley and conveyor belt during this operation. Support the weight of the tail pulley during rotation from the outside of the conveyor belt.

Adjust until aligned

Aligned

Adjust until aligned

Aligned

INCORRECT Alignment

CORRECT Alignment Figure 3

c. Adjust the set screws on the Tail Pulley Assy until the centerline of the Tail Pulley Shaft is in line with the indicator marks on both the Tail Plates (Figure 3). This position is “Neutral”. d. Adjust the set screws of the Center Drive Idler Assy’s until the centerline of the Idler Shaft is in line with the indicator marks on the Mounting Plates (Figure 4). This position is “Neutral”, and the conveyor belt is now ready for tracking.

Figure 4

e. Proceed to step 6 to install Underside idlers (if necessary).

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13â&#x20AC;&#x2122; (continued) s Install Underside Idlers Underside Idlers are used on Automation Series conveyors to prevent the belt from sagging below the bottom of the extruded aluminum frame. Not all conveyors require underside idlers. Variables, such as conveyor length and conveyor width affect whether underside idlers are used. If your conveyor requires underside idlers, they will be included in your conveyors packaging. a. Locate the package that contains Underside idler assemblies. There are two different styles of underside idlers, dependent on the width of the conveyor: stub idlers and full width idlers. Both styles mount to the conveyor in the same way. (Figure 1).

Full Width Idler Assy

Stub Idler Assy

b. Loosen the two M5 Socket head Cap Screws tightened in the clamp from the extruded guard (Figure 2). For Full Width Underside Idlers, loosen the screws on both ends, and also the M5 set screws on the bottom of the Clamp Plates (Figure 3).

Figure 1

Extruded guard

Clamp Plate M5 Set Screw

Figure 2 Figure 3

c. Determine the location for Underside Idler assemblies on the conveyor; they should be evenly spaced down the length of the conveyor (Figure 4). If stub idlers are used, they should be mounted directly across from each other.

Equally Spaced

Figure 4

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13â&#x20AC;&#x2122; (continued)

Tighten M5 SHCS

d. Clamp the Underside idler assembly into place by threading the M5 Socket Head Cap Screws through the Clamp Plate and into the extruded guard. The assembly will lock against the bottom corner of the aluminum extruded conveyor frame (Figure 5). For Full Width idler assemblies, the M5 Set Screws will also need to be tightened through the Clamp plate against the flat on the idler shaft (Figure 6).

Figure 5

Tighten M5 SHCS

Tighten against shaft flat Figure 6

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13’ (continued) t Orient the Conveyor based on the Drive Location a. Set the conveyor in its operating position, taking care to note its drive location. AS65 Conveyors ship with a left hand drive or right hand drive that is predetermined at the time of the order, and can be decoded in the conveyor's part number. The 13th digit in the part number will indicate the side the Center Drive Guard is protruding toward, from the point of reference at the discharge end of the conveyor. The 14th and 15th digits in the part number indicate whether the conveyor was tracked at the factory with the Fixed End or the Tension Release Tail at the discharge end of the conveyor. The following is an example of an 8” wide x 15’ long conveyor: AC61H08-180-LFE-MAE There are four combinations available for the AS65 Center Drive (Figure 1): LEF Left Hand Guard, Fixed End at Discharge REF Right Hand Guard, Fixed End at Discharge RFE Right Hand Guard, Tension Release Tail at Discharge LFE Left Hand Guard, Tension Release Tail at Discharge Left hand and right hand are defined as if you are standing at the discharge end of the conveyor. F

LEF

L E

REF

R RFE

LFE

Figure 1

Tail Adjustment Set Screws

Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.05 Conveyors Longer than 13â&#x20AC;&#x2122; (continued) u Track the Belt The drive will have to be installed and operational before the belt can be tracked. a. Refer to Section 2.13 for installing the Drive. b. Refer to Section 3.02 for the procedure for Tracking the Belt.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.06 Aluminum Exact Width Stands Aluminum Exact Width Stands can be located anywhere along the length of the conveyor, as they mount directly into the aluminum extruded frameâ&#x20AC;&#x2122;s T-Slot. Ideally, the stands should be equally spaced along the length of the conveyor. For stability, the maximum distance the stands should be placed apart is 6 feet. The maximum distance a stand should be located from the tail end is 9 inches, and the maximum distance a stand should be located from the Fixed Idler end is 20 inches (Figure 1).

20 in Max.

6 feet Max.

9 in Max.

Figure 1

n Prepare the Stand for Installation a. For shipment, the stands will have their mounting brackets slid down the extrusion. Use a 3mm Allen wrench to loosen the M6 Socket Head Screws holding the Brackets and move them up to engage the conveyor frame, approximately 1 1/2â&#x20AC;? (or more for cleated belts) (Figure 2).

Operating Position

Shipping Position

Figure 2

b. If the stands are to be used with Aluminum Cross Ties, it is advised to attach the Gusset Plates prior to mounting the conveyor (Figure 3). Refer to Section 2.08 on Aluminum Cross Ties for specific instructions.

Gusset Plate

Figure 3

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.06 Aluminum Exact Width Stands (continued) o Install the Stand

Insert into Frame

a. Remove the Drop In Nuts from the bag of fasteners wrapped to the Exact Width Stand.

b. Insert the Drop In Nuts into the T-Slot in the conveyor frame. Line up the stand assembly brackets to the Drop In Nuts, insert the M6 Socket head Cap Screws through the bracket and fasten the stand to the frame (Figure 4).

p Adjust the Height using the Leveling Feet Figure 4

Hex Nut

The Leveling Feet on all of QC Industries Stands are designed to allow fine adjustment and so they can be lagged to the floor. Note: if it is not feasible to permanently attach the stands to the floor or the conveyor is to be made mobile with casters, then Cross Ties or Angle Braces must be used. To adjust the stand height with the Leveling Feet: a. Use a large adjustable wrench to loosen the Hex Nut

Lag to floor here

Welded Hex Figure 5

b. Rotate the hex welded to the foot to the desired height (Figure 5). c. Retighten the Hex Nut to secure it in position.

Injury is possible if the stands are not lagged to the floor, cross ties are not used, or angle braces are not present. Never place a conveyor in operation until all proper mounts are installed and secured.

d. Frame alignment is one of the key items that assure the belt properly tracks during startup. Make sure the conveyor frame has no twist by using a bubble level and checking measurements from the mounting surface. e. Proceed to Section 2.07 for instructions on installing Angle Braces. f. Proceed to Section 2.08 for instructions on installing Cross Ties. g. Proceed to Sections 2.11 â&#x20AC;&#x201C; 2.12 for instructions on installing Sides and Guides.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.07 Angle Braces When it is not feasible to bolt the Aluminum Exact Width Stands to the floor, they can be stabilized by use of Angle Braces. Angle Braces will only work for conveyors mounted horizontally. If your conveyor is mounted at an incline, Cross Ties must be used instead. Also, Angle Braces will only work with stands that are 18” or taller (i.e. part number AS40-18-21-WW). Insert into extrusion

Angle Braces are shipped as a set, with one Right Hand Brace and one Left Hand Brace. Each Brace has four Socket Head Cap Screws and four Drop in Nuts. Before installing Angle Braces, the Aluminum Exact Width Stands should already be assembled to the conveyor.

n Install the Angle Braces to Exact Width Stands a. Start by rotating two Drop In Nuts into the stand leg extrusion’s TSlot, one in each slot (Figure 1).

Figure 1

b. Insert two Drop In Nuts into the conveyor frame’s T-Slot. c. Place the Angle Brace over the Drop In Nuts, and insert the Socket Head Cap Screws into the Drop In Nuts, but do not fully tighten them (Figure 2). d. Tighten the Socket Head Screws so the Brace is secured to the stand, and repeat the installation for the Brace on the other side. e. Frame alignment is one of the key items that assure the belt properly tracks during startup. Make sure the conveyor frame has no twist by using a bubble level and checking measurements from the mounting surface. Insert Drop In Nuts before mounting

f. Proceed to Sections 2.11 – 2.12 for instructions on installing Sides and Guides.

Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.08 Aluminum Cross Ties When it is not feasible to bolt the Aluminum Stands to the floor, the conveyor and stand assembly can be stabilized by use of Cross Ties. Cross Ties are sold in standard lengths, and are meant to be cut to length during installation based on the final placement of the stands. The Cross Ties can be installed once the conveyor has been secured to the stands. In the box that contains the Cross-Ties, there will be a bag containing the Cross Tie Gusset Plates and fasteners.

n Install the Gusset Plates to Aluminum Stands a. Insert four Drop In Nuts into each stand leg extrusion’s T-Slot, two in each slot (Figure 1).

Rotate into extrusion

b. The Gusset Plate should be positioned over the Drop In Nuts in the stand extrusion T-Slot and secured with the Socket Head Screws. Slide the Cross Tie Slide nut nuts into the cross tie into extrusion prior to extrusion assembly (Figure 2). Although there are twelve holes in the Gusset Plate, only the Cross Tie smaller eight holes will extrusion be used.

Figure 1

o Install the Cross Tie Extrusions

Gusset Plate

Figure 2

a. Ensure stands are level using a bubble level on the conveyor slider bed. b. Measure the distance between the stands and cut the Cross Tie Extrusion to fit with a saw blade that is appropriate for cutting Aluminum (Figure 3).

Cut to Length

c. The Gusset Plates can mount to the inside or outside of the stand’s leg, or to the stand’s Cross Member if there is no room on the leg. Figure 3

d. Proceed to Sections 2.16 – 2.18 for instructions on installing Sides and Guides.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.09 Stands with Casters With the exception of the Single Post Fixed Base style, Exact Width Stands have an option for swivel locking casters, versus the standard stand feet.

n Adjusting the Conveyor height with Casters a. The caster’s stem can be used to fine tune height adjustment, up to 1 1/2” up or down. Use a large adjustable wrench to loosen the hex nut, engage the swivel lock, then rotate the caster to the desired height by hand, and finally retighten the Hex Nut to secure it in position (Figure 1).

o Secure the System a. When the conveyor is not being moved or is in operation, the Caster’s swivel lock should be engaged. It is conveniently located over the caster’s wheel so it can be engaged and disengaged by foot. b. QC Industries requires the use of Cross Ties or Angle Braces if Casters are used. Note: The width of the system should be no less than 1/3 of the system’s height (i.e. for a 36” high system, a stand assembly on casters should be at least 12” wide). When assembling, please make sure the assembly is stable for your application.

Figure 1

Warning: Moving conveyors with casters can create dynamic forces that could tip the conveyor. Use caution when moving a conveyor with casters.

c. Proceed to Sections 2.11 – 2.12 for instructions on installing Sides and Guides.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.10 Side Mounts The Side Mounts are used to mount the conveyor to a flat mounting surface. There are two versions available: Flush Mount (1A0030A-001), and 5” Raised Mount (1A0030A-005). The Flush Mounts are used for conveyors with no cleats or underside idlers. They will create a top of belt height of approximately 49.5mm [1.95”] from the mounting surface. If the conveyor has cleats, corrugated sidewalls, or underside idlers, the 5” Raised Side mounts are used. They will create a top of belt height of approximately 128.5mm [5.06”] from the mounting surface. The same rules for stand placement on the conveyor apply for mounts.

n Flush Side Mounts a. With Flush Mounts, the mount can be installed on the conveyor anywhere along its length where the T-Slot is exposed and accessible.

Insert into T-Slot

b. Insert the Drop In Nuts into the T-Slot in the conveyor frame. Line up the Flush Mount to the Drop In Nuts, insert the M6 Socket head Cap Screws through the mount and fasten to the frame (Figure 1).

Figure 1

o Raised Side Mounts

a. With Raised Mounts, the mount can be installed on the conveyor anywhere along its length where the T-Slot is exposed and accessible. However, the conveyor should be supported at least every 6’, and the maximum distance the mount should be from the tail end is 9“, and 20” from the drive end.

Foot Facing Inward

Insert into T-Slot

Foot Facing Outward

b. Insert the Drop In Nuts into the T-Slot in the conveyor frame. Line up the Raised Mount to the Drop In Nuts, insert the M6 Socket head Cap Screws through the mount and fasten to the frame. The Raised Mount mounting foot can face either inward or outward (Figure 2).

Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.11 Fixed Side Rails Fixed sides are available in 3 heights: 1/3”, 1”, and 2”. The 1” high and 2” high Side Rails have a Tslot integrated into them that can be used to mount accessories. For convenience, the T-slot in the side rail is sized for the same Drop In Nuts used for the conveyor frame. Fixed sides are available in 2 styles: as a plain aluminum extrusion, and with UHMW wearstrip. Fixed Sides are designed to span the full length of the conveyor; however, the rail length will be broken into three segments that accommodate the conveyor’s full length.

n Installing Fixed Sides Fixed Sides should not be installed until the conveyor is mounted on its stands or supports. The conveyor will be shipped with Siderail Clamps fastened to the side of the conveyor frame. In general, clamps will be spaced every 12” for 1/3” and 1” sides, every 9” for 2” sides.

Tracking Block

Fixed Idler End

Loosen M6 SHCS’s

a. Loosen the M6 Socket Head Screws in the Tracking Blocks that are closest to the Fixed Idler End (Figure 1).

Figure 1

Tail End

b. Loosen the M6 Socket Head Screws in the Clamp Blocks nearest the Tail Assembly (Figure 2). Clamp Block

c. Slide the Side Rail extrusion through the Side Rail Clamps, Tracking Blocks, and Tail Clamp grooves, so the rail ends are even with the ends of the conveyor. Insert the anchor bars in the T-Slot of the guide rail for rigidity (Figure 3).

Loosen M6 SHCS’s

d. Using a 3mm Allen Wrench tighten the M6 Side Rail Clamp Screws. e. Retighten the Socket Head Screw in the Tracking and Clamp Blocks and M6 set screws in the anchor bars.

Figure 2

Anchor Bars & Set Screws Adjust edge of Guide Rail to be even with Fixed Idler End

Adjust edge of Guide Rail to be even with Tail End

Figure 3

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.12 Adjustable Guides Adjustable Guides are available in 3 heights: 1”, 2”, and 3”, and are available with either thumbscrew adjustment or set screw adjustment. The Guiderails are supported by mounting bracket assemblies that must be installed on the conveyor prior to rail installation.

n Mount the Guide Brackets a. Attach the Guide Brackets to the conveyor frame using the M6 Socket Head Cap Screws and Drop In Nuts provided (Figure 1). The large hole of the guide bracket should face upward. b. The Guide Brackets should be spaced on approximately 24” centers down the length of the conveyor. c. Secure a rod vertically to the Guide Bracket with an M6 Socket Head Cap Screw from the underside of the Guide Bracket.

Insert into Frame Figure 1

o Prepare the Guide Rail a. Slide Drop In Nuts into the tee slot of the Guiderail. (Figure 2). b. Thread the Adjusting Rod into the Drop In Nut and hand tighten, but leave it loose enough that the rod and screw can still slide in the tee slot. The rod’s locations should be approximately the same as the Guide Brackets mounted to the conveyor.

Insert into Extrusion

c. Place a round Cross Block all the way down each adjusting rod so it touches the Guiderail and tighten it down with the Set Screw or Thumbscrew. Figure 2

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.12 Adjustable Guides (continued) p Install the Guide Rail to the Brackets a. Install the Guiderail/Rod/Cross Block assembly over the vertical rods connected to the Guide Brackets, and secure them in place vertically (Figure 3). b. By loosening and tightening the fasteners in the Cross Block, the Guiderail can now be adjusted vertically or horizontally as needed; once in the desired location, finish tightening the horizontal rods so they hold the Guiderail rigidly. c. Proceed to Sections 2.13 instructions on installing the Drive.

for

Figure 3

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2.13 Installing a Heavy Duty Motor AS65 conveyors come with a Standard Duty gearmotor completely assembled from the factory, as standard. If you have a Standard Duty gearmotor, you do not need to install the drive. The Heavy Duty Drive is designed for heavier loads, more demanding applications, and for customers who wish to use their own 56 frame motor. It is a drive that utilizes a Leeson right angle gearbox. If you have purchased an optional Heavy Duty Drive, the gearbox will be assembled to the conveyor, but the motor will need to be installed. Wire the motor using the appropriate diagrams of the motor style, voltage and phase you have purchased. QC Industries recommends that all wiring be completed by a certified electrician. Heavy Duty motors are always shipped in their own box. They must be installed onto the speed reducer by the installer.

n Discard the Motor Key and use the Reducer Key a. Unpack the motor from its box and packaging. b. Discard the key that is included with the motor. Only the special key provided with the Leeson Speed Reducer should be used with the Leeson Speed Reducer (for more, refer to Leeson’s Speed reducers Installation, Lubrication, and Maintenance Instructions document provided with the speed reducer).

o Install the Motor to the Speed Reducer a. On the Speed Reducer, rotate the input quill by hand until the keyway is in the 12 o’clock position. Do the same with the motor. b. Open the packet of anti-seize compound that shipped with the Speed Reducer. Generously apply it to the speed reducer input quill and motor shaft. c. Install the motor onto the speed reducer by guiding the keyed shaft into the speed reducer input quill. d. Rotate the motor until the workbox is in the desired location (normally pointing horizontally away from the conveyor) and secure it in place with the 4 Hex Head Screws provided using a 9/16” Wrench. e. QC Industries recommends that all wiring be completed by a certified electrician. Refer to the documentation contained in the motor’s box for instructions on electrical connections. Once the motor is wired, the conveyor is ready for operation.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.01 Maintenance Foreword Managing conveyor life is both a comprehensive and important consideration from the day a system is conceived until the day it is retired from service. From a business perspective, maintenance is an essential activity for the achievement of optimal return on investment, as well as a key to remaining competitive in a hyper-competitive world. Like maintenance for many other systems, the maintenance of conveyor systems divides into three broad categories: predictive, preventive, and corrective. The obvious advantage of predictive and preventive maintenance is that downtime surprises can be avoided, and when action needs to be taken, all of the parts, materials, and timing can be arranged for operational convenience. To assure the highest performance for your conveyor system, QC Industries has combined a selection of high quality durable components and superior design criteria that support all aspects of conveyor operational effectiveness with the minimal amount of conveyor preventive maintenance. Preventive maintenance, such as the cleaning of the conveyor, replacement of conveyor belt and bearings will be regimented by the type of environment the conveyor system is subjected to, the number of hours in operation, and the amount of performance demanded of the system. Predictive measures, such as belt replacement schedules, periodic bearing replacement intervals, and overall equipment inspection shall be determined by the environment the conveyor is subjected to, the number of hours in operation, and the production effects of measures taken at the corrective phase. Maintenance, in general, affects all aspects of conveyor operational effectiveness and risks, not just system availability and cost â&#x20AC;&#x201D; specifically safety, operational efficiency, energy efficiency, product quality, and environmental integrity. The following sections are QC Industriesâ&#x20AC;&#x2122; requirements for assuring the conveyor system is always operating at the factory specifications with minimal production interruption please follow these guidelines. If any questions arise please call our customer service department at (513) 753-6000.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.02 Belt Tracking Automation Series conveyors 13’ long and under are shipped assembled with the belt pre-tensioned and pre-tracked from the factory. However, after the conveyor is installed in its’ final location, it is still necessary to ensure the belt is properly tracked using the instructions below. Ensure the conveyor frame is level over its’ entire length and width prior to adjusting belt tracking. Since Automation Series Center Drive conveyors have belt tracking controls in numerous locations, the following steps may need to be repeated multiple times, as adjustments in one location may affect the tracking at another. On longer conveyors, wider conveyors, or conveyors running at slower speeds, tracking adjustments will take more time than on shorter and narrower conveyors. Let the belt make several revolutions before making additional adjustments on these types of conveyors.

n Track at the Drive Pulley a. There are four M6 set screws holding two Center Drive Idler Assy’s in the drive area, two on each side of the conveyor. These set screws have the ability to be threaded in or out to steer the conveyor belt through the drive area (Figure 1).

Set Screws

Figure 1 Drive Side Mounting Plate

Slide guard out, then down

b. Remove the Conveyor Belt Guard from the Center Drive Assy by removing the three M5 Button head Cap Screws from the Mounting Plate opposite the gear motor. Loosen, do not remove, the three M5 Button head Cap Screws from the drive side Mounting Plate. Slide the guard away from the drive side plate by pulling it out and down at an angle. It is not necessary to remove the drive package from the conveyor to remove the belt guard (Figure 2).

Figure 2

Warning: Removing the Conveyor Belt Guard from the conveyor during operation exposes potential pinch points where fingers, hands, clothing, or hair could be caught. Use care around the drive area with guard removed. Reinstall guard when finished tracking belt.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.02 Belt Tracking (continued) Infeed Idler

Discharge Idler

Belt Flow

c. With the conveyor running slowly, observe the belt position on the Drive Pulley. If the belt is NOT centered on the Drive Pulley, locate the Center Drive Idler Assy that touches the belt on the Infeed side of the Drive Pulley (Figure 3).

d. Adjust the Infeed Idler so the belt tracks to the center of the Drive Pulley by threading in or out the M6 set screws on either side of the Idler Assy (Figure 4). Drive Pulley Figure 3

e. Adjust the Discharge Idler Assy only if the belt is NOT centered on it.

Adjust Tracking Screw this direction

Belt moves this direction

f. Reinstall Conveyor Belt Guard only after belt is completely tracked along the conveyor.

Adjust Tracking Screw this direction

o Track the Fixed Idler End

Belt moves this direction

Figure 4

a. Loosen (do not remove) the six M6 Screws in the Bearing Blocks (three on each side), about one-half turn. b. With the conveyor running, rotate the M6 Square Head Tracking Screw toward the Pulley on the side of the conveyor where the belt is riding too close â&#x20AC;&#x201C; this will set the Idler Assembly at an angle and move the belt away from that side (Figure 5).

Loosen M6 SHCSâ&#x20AC;&#x2122;s Bearing Block

c. For best results, make small adjustments to only one side at a time. The Fixed Idler End is tracked when the belt can make a full revolution without contacting either bearing plate. d. Re-tighten all six M6 Bearing Block Screws.

Tracking Screw

Belt moves this direction

Adjust Tracking Screw this direction

Figure 5

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.02 Belt Tracking (continued) p Track the Tail End A unique feature to QC Industriesâ&#x20AC;&#x2122; Automation Series conveyor is the Tension Release Tail Assembly. This assembly, which provides a quick release mechanism for relieving belt tension, also provides belt tracking and belt tensioning capabilities. The pulley is initially assembled to the conveyor in the â&#x20AC;&#x153;neutralâ&#x20AC;? position (defined as the index mark on the pulley aligned to the index mark on the tail plate), but may have been adjusted at the factory for belt tracking purposes; therefore, your tail assembly may not be in the neutral position when received. a. With the conveyor running, determine the side of the conveyor where the belt is riding too close. On that side, adjust the M8 Set Screw on the Tail Pulley assembly so that the Tail Pulley Assembly moves away from the conveyor. Use the index marks on the tail shaft and tail plate as the points of reference. This will set the Tail Pulley Assembly at an angle to move the belt away from that side (Figure 6). b. The tracking adjustment at the tail end is very responsive. For best results, make only minor adjustments. Allow the belt to make several revolutions to determine if more adjustment is necessary. The Tail End is tracked when the belt can make several revolutions without contacting the inside edges of the frame.

Index Marks

Adjust Pulley this direction

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

M8 Tail Adjustment Set Screw

Belt moves this direction Figure 6

3.03 Belt Change QC Industries recommends stocking at least one replacement belt for every conveyor ordered. This will minimize downtime and ensure optimum performance for your particular application.

n Remove the existing belt a. At the tail end of the conveyor, locate the push buttons on both sides of the Tension Release Tail Assembly. Simultaneously push in both buttons to disengage the locking mechanism, and rotate the Tension Release Tail Assembly up towards the opposite end of the conveyor (Figure 1).

Push Button

Tension Release Tail Assy

b. Remove tension from the belt by rotating the Tension Push Button Release Tail Assembly completely up to the disengaged Rotate Up position. Support the Tail Pulley Assembly during rotation. The Tension Release Tail Assembly will rest in the up, Figure 1 unlocked position (Figure 2). c. Remove both Center Drive Idler Assyâ&#x20AC;&#x2122;s from the drive area by threading out all four M6 Tracking Adjustment Set Screws, and pulling the idlers out of the Mounting Plate slots (Figure 3). Retain Idlers for Support Tail belt reinstallation. Pulley Assy M6 Adjustment Set Screws

Figure 2

d. There will now be enough slack in the belt to loop it off of the Fixed and Tail Ends and transfer the excess slack to the Drive area. Pull the remaining belt threaded through the Drive area away from the Drive Mounting Plate (Figure 4).

Pull Idler out of slots

Pull belt away from the drive side, towards the opposite side of the conveyor

Figure 3

Figure 4 QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.03 Belt Change (continued) o Install the new belt a. Starting at the Tail End, loop the belt over the end of the frame and Tension Release Tail Assembly. Ensure the Tension Release Tail Assembly is in the up, unlocked position (Figure 5). b. Loop the belt around the conveyor frame towards the Fixed Idler End, threading the belt through the drive area and leaving slack for the Center Drive Idler Assy’s. Loop the end of the belt around the Fixed Idler End (Figure 6).

Tension Release Tail Assy in Up Position

Loop Belt starting at Tail End Figure 5

Loop Belt over conveyor in this direction starting at Tail End

Fixed Idler End

Leave belt slack here for Center Drive Idler Assy

Leave belt slack here for Center Drive Idler Assy Figure 6

c. Insert Center Drive Idler Assy’s back in the drive area by sliding them into the Mounting Plate slots and threading in the four M6 Tracking Adjustment Set Screws (Figure 7). Ensure recesses in shaft faces outward for dog point set screws to engage.

Align index marks on Idler Assy’s to index marks on Mounting Plates

d. While supporting the weight of the Tail Pulley Assembly, rotate the Tension Release Tail Assembly down into the locked, run position. Take caution to keep hands and fingers away from the edge of the conveyor frame where the Tension Release Tail Assembly will engage (Figure 8). Insert Idler Assy in slots CAUTION! Pinch Point

Figure 7 Rotate Down

CAUTION! Pinch Point

Support Weight of Pulley Figure 8

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.03 Belt Change (continued) e. Set the initial tension of the conveyor belt (Neutral) by aligning the index marks on the Tail Pulley Assembly to the index marks on the Tension Release Tail Assembly (Figure 9).

Adjust until Aligned

Aligned

INCORRECT ALIGNMENT

CORRECT ALIGNMENT Figure 9

f. The conveyor is now ready to be tracked as instructed in Section 3.02.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.04 Adding Tension With the exception of extended length conveyors, all Automation Series conveyors are shipped assembled with the belt pre-tensioned and pre-tracked from the factory. This process ensures that the belt has the recommended amount of tension to maximize the conveyors load carrying capacity. For the life of a standard belt, you should not have to adjust its tension. However, if there is a need to add additional tension to extend the service life of a belt that has elongated, the Tracking Screws may be used to increase tension. It is recommended that the conveyor be stopped before making tension adjustments. Note: over-tensioning belts adds unnecessary load to bearings, and subsequently will reduce the bearings useful life.

n Add tension at the Center Drive Assy a. There are four M6 set screws holding two Center Drive Idler Assy’s in the drive area. Adjust the screws on both sides of one idler equally so the idler moves toward the center of the assembly (Figure 1). Start with the idler that is over the drive pulley. If additional tension is needed, adjust the other idler in the center drive assembly the same way. The screws should be extended the same amount so the belt tracking is not adversely affected (refer to Belt Tracking in Section 3.02).

Adjust screws equally

Adjust this idler first…

o Add tension at the Tail End

…adjust this idler last

Figure 1

b. Increase the belt tension by adjusting the M8 set screws at the Tail Assembly so the Tail Pulley moves away from the conveyor frame (Figure 2). The screws should be extended the same amount so the belt tracking is not adversely affected (refer to Belt Tracking in Section 3.02).

p Add tension at Fixed Idler End Pulley moves outward this direction

c. Loosen (do not remove) the six M6 screws in the Bearing Blocks (three on each side), about onehalf turn (Figure 3). Loosen M6 SHCS’s

Adjustment Tail Set Screws equal amount

Tracking Screw Bearing Block

Figure 2

d. Increase the tension by extending the M6 Square Head Tracking Screws on both sides of the conveyor until desired tension is achieved. The screws should be extended the same amount so the belt tracking is not adversely affected (refer to Belt Tracking in Section 3.02). e. Retighten the six M6 screws to lock the assembly in position.

Adjust Tracking Screws same amount in this direction Figure 3

f. If after following these steps additional belt tension is needed, it is recommended that a new belt be purchased.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.05 Belt Care n Cleaning Belts can usually be cleaned with general household cleaners; however some cleaners (alcohols, acetone, MEK, chlorinated solvents, etc.) may attack specialty belts. Never hose off the bearings or use solvents in these areas as this may significantly reduce bearing life.

o Physical Damage Worn edges do not hurt the conveyor's operation, as the pulleys are crowned; however, the cause of the edge wear should be determined. If fibers from exposed frayed edges need to be removed, they can be trimmed by mechanical means (scissors), or by holding a heat source close (such as a lighter). Scoring Lines in the belt's surface could be due to product collecting between the frame's underside flange and the belt. If the conveyor has a wiper, product could be trapped at the scraping edge. Accessories, such as adjustable guides or underside idlers could be improperly positioned and in contact with the belt.

p Camber Belt camber is the lateral oscillation of the belt, most noticeable at the drive end between the bearing plates. All belts have some camber due to the endless splice not being perfectly square. Crowned pulley and tracking adjustments should overcome the belt's camber, but in some cases will not (such as if the belt is excessively worn or has been exposed to an inappropriate chemical or solvent). Excessive camber is when the belt cannot be tracked without the edges contacting the bearing plates at any point during a revolution. It is possible that the conveyor can continue to perform at a high level even with excessive camber, but if it is a problem, replacement of the belt is suggested.

q Slippage Belt slippage occurs when the belt is under-tensioned for the load, which could be caused by a number of factors: 1) Excessive load on the conveyor. If this is suspected, contact QC Industries with the parameters of the application (speed, load, conveyor size, duty service and cycle, mounting) to verify if the conveyor and drive are of sufficient size. 2) Reduced friction between the belt and drive pulley. 3) Belt elongation due to over-tensioning. 4) Excessive belt wear due to accumulating product. 5) Belt elongation due to exposure to a chemical or ultraviolet light. If slippage cannot be overcome by either removing the condition causing it or by adding tension at the drive end, it is likely the belt needs to be replaced.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.06 Bearing Replacement Automation Series conveyors use sealed for life, deep groove ball bearings. QC Industries recommends that these bearings be checked yearly at a minimum, and removed and replaced when worn. The replacement interval is dependent on the speed at which the conveyor is running, the load on which the conveyor is carrying, and the environment in which the conveyor is in. Note: The replacement interval can be drastically affected by environmental issues such as moisture, dust, heat, and chemicals. Please consider these factors when determining the correct inspection and replacement interval for your application.

n Fixed Idler End Bearing Replacement a. Remove the conveyor belt (refer to Belt Change Section 3.03) from the conveyor. The Fixed Idler Assembly may need to be removed from the conveyor for easier access.

Access holes in Bearing Blocks

b. At the fixed idler end of the conveyor, locate the bearing set screw access hole in each Bearing Block. Rotate the Fixed Idler Pulley to align the bearing set screws with the access hole and insert a 2mm Allen Wrench through the hole. Remove the three set screws in the Bearing’s lock collar (Figure 1). c. Remove the Bearing’s lock collar by sliding it off the inner race of the bearing and out of the bearing block. Remove the three M6 Low Head Cap Screws in the bearing Block with a 3mm Allen Wrench and slide the bearing and bearing block off of the Fixed Idler Pulley’s bearing journal. Ensure the pulley’s journals do not get nicked or gouged, as this may complicate the installation of new bearings (Figure 2). If the bearings will not easily slide off of the drive pulley journals, it may be necessary to soak the bearings in oil for approximately 30 minutes and use a flat head screwdriver (or similar tool) to aid in removal. Gently work the flat end of the tool around the diameter of the bearing using the end of the pulley for leverage, using caution to not damage to aluminum bearing housings.

Bearing Block

Bearing lock collar set screws (3 per bearing)

Figure 1

Idler Pulley bearing journal Bearing Lock Collar Figure 2

NOTE: Do not use excessive force (like a press) in trying to remove bearings.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.06 Bearing Replacement (continued) d. Remove the Bearing from the Bearing Block by rotating and orienting it in the Bearing Block until it slides out of the access slots. The lock collar must be removed for the bearing to exit the Bearing Block. Although the spherical bore of the bearing Block allows rotation of the bearing for removal and installation, there is a light press fit that may require use of a round bar, screwdriver, or similar object for leverage (Figure 3).

Bearing Access Slots

Bearing exits in this direction

e. Install new Bearings in the Bearing Blocks following the previous steps in reverse order.

Figure 3

f. Clean the Fixed Idler Pulley bearing journal surfaces. Then apply a light coat of Anti-Fretting agent (such as SKF’s LGAF 3E/0.5) to bearing bores and Pulley bearing journals prior to sliding the Bearings/Blocks back onto the Pulley journals. This will inhibit the bearing seizing to the pulley journals over time and ensure easy disassembly for future bearing replacements. g. Tighten the three M6 Low Head Cap Screws in each Bearing Block with a 3mm Allen Wrench. Center the Fixed idler Pulley V-Groove to the V-Groove in the slider bed. The pulley and new bearings must be in alignment. Rotate the pulley to ensure it turns smoothly. h. Install the lock collar over the extended inner race of the bearing and orient the set screw holes in the lock collar to the dimples on the extended inner race (Figure 4). Align dimples on inner race…

…to set screw holes in lock collar Figure 4

j. Insert the lock collar set screws through the access hole in the Bearing Block. Ensure the set screws seat in the dimples on the inner race before fully tightening.

k. Tighten the set screws with a torque wrench to 15 in-lbs, using a 2mm hex key. The proper sequence to tighten the bearing set screws is to tighten set screw “A” to half the recommended tightening torque. Then tighten set screw “B” to half the recommended tightening torque. Then tighten set screw “C” to the full recommended tightening torque. Go back to set screw “A” and “B” and recheck the torque. Tighten set screw “A” and “B” to the full 15 in-lbs (Figure 5). To prevent damage to bearing, do not exceed recommended tightening torque limits.

Set Screw “B”

Set Screw “C” Set Screw “A” Figure 5

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.07 Fastener Tightening Torque Specifications The following torque values are supplied for general informational purposes associated with disassembly and reassembly of QC Industries conveyors and equipment. It is the end user’s responsibility to inspect all equipment at installation to ensure that fasteners have not loosened during shipment, and to ensure that fasteners are secure at all times. Conveyor Fasteners Description Fixed Idler Bearing Housing Screws Fixed Idler Jacking Block Screws 18”-24” Wide Frame Screws (Torx Head) 18”-24” Wide Frame Screws (Torx Head) for Tie Bar 2”-12” Wide Tie Bar Screws Tension Release Tail Assy Pivot Button Head Shoulder Screw Tension Release Tail Assy Stiffener Mtg Screws Tension Release Tail Assy Mtg. Set Screws Underside Idler Clamp Screws Conveyor T-Slot/Drop-in Nut Mtg. Screws (includes fasteners for Mounts, Sides & Guides, Angle Braces, etc) Fixed End Idler Bearing Set Screws

Part # SLHCS-M6X100X010-BX SHCS-M06X100X010-ZP PHCS-M06X100X018-ZP-ST

Fastener M6 x 10mm LG M6 x 10mm LG. M6 x 18mm LG.

Torque 8 ft-lbs. 8 ft-lbs 7 ft-lbs

Section 3.02 3.07 2.05

PHCS-M06X100X025-ZP-ST

M6 x 25mm LG.

7 ft-lbs

2.05

SHCS-M06X100X010-ZP 1D0225A

M6 x 10mm LG. M6 x 14mm LG.

10 ft-lbs 8 ft-lbs

2.05 3.07

SLHCS-M05X080X010-ZP

M5 x 10mm LG.

5 ft-lbs

3.07

SHSS-M06X100X006-ZP

M6 x 6mm LG.

5 ft-lbs

3.07

SHCS-M05X080X016-ZP Varies

M5 x 16mm LG. M6

8 ft-lbs 2.05 10 ft-lbs 2.10 2.11 2.12

1D0131A

M4 x 5mm LG.

15 in-lbs 3.06

Part # FHCS-M6X100X016-ZP SHCS-M6X100X025-ZP

Fastener M6 x 16mm LG M4 x 15mm LG

Torque Section 10 ft-lbs. 70 in-lbs.

BHCS-M08X125X025-ZP

M8 X 25mm LG.

20 ft-lbs. 2.13

Fastener M6

Torque 10 ft-lbs

Drive Mounting Package Fasteners Description CD Mounting Plate Mtg. Screws Drive Pulley Bearing Lock Collar Mtg. Screws Heavy Duty Drive Gearbox Output Shaft Mtg Screw

Stand & Stand Accessory Fasteners Description Stand T-Slot/Drop-in Nut Mtg. Screws

Part # Varies

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Section 2.06

2"-12" Wide Automation Series Conveyor Center Drive with Standard Belt LEGEND 5

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MAE 2

Item 1 2 3 4 5 6

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1D00XXALLLL AC6-WW-LLL-MAE 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL SLIDER BED ALUMINUM EXTRUDED BELT AUTOMATION SERIES CENTER DRIVE STANDARD ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2"-12" Wide Automation Series Conveyor Center Drive with V-Guide Belt LEGEND 5

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MVE 2 5

Item 1 2 3 4 5 6

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1D00XXALLLL AC6-WW-LLL-MVE 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL SLIDER BED ALUMINUM EXTRUDED BELT AUTOMATION SERIES CENTER DRIVE V-GUIDE ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

18"-24" Wide Automation Series Conveyor Center Drive with Standard Belt

18"-24" Wide Automation Series Conveyor Center Drive with Standard Belt LEGEND Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MAE 3

6 1

Item 1 2 3 4 5 6

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1A0046A AC6-WW-LLL-MAE 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL ASSY MULTI-PIECE FRAME BELT AUTOMATION SERIES CENTER DRIVE STANDARD ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

18"-24" Wide Automation Series Conveyor Center Drive with V-Guide Belt LEGEND 5

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MVE 3

6 1

Item 1 2 3 4 5 6

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1A0046A AC6-WW-LLL-MVE 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL ASSY MULTI-PIECE FRAME BELT AUTOMATION SERIES CENTER DRIVE STANDARD ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

2"-12" Wide Auto. Series Extended Conveyor Center Drive with Standard Belt LEGEND 5

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MAE

4 9

1 10 5

Item 1 2 3 4 5 6 7 8 9 10

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1D00XXALLLL 1D00XXALLLL AC6-WW-LLL-MAE 1D0140A 1D0044A SHCS-M06X100X010-ZP 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL SLIDER BED ALUM. EXTRUD. EXTENSION SECTION SLIDER BED ALUM. EXTRUD. DRIVE SECTION BELT AUTOMATION SERIES END DRIVE STANDARD TIE BAR EXTENDED FRAME CONVEYORS ANCHOR BAR SCREW SOCKET HEAD CAP M6x1.0 10mm LG. ZP ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

2"-12" Wide Auto. Series Extended Conveyor Center Drive with V-Guide Belt LEGEND 5

@ 2

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MVE

4 9

7 8

1 10 5

Item 1 2 3 4 5 6 7 8 9 10

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1D00XXALLLL 1D00XXALLLL AC6-WW-LLL-MVE 1D0140A 1D0044A SHCS-M06X100X010-ZP 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL SLIDER BED ALUM. EXTRUD. EXTENSION SECTION SLIDER BED ALUM. EXTRUD. DRIVE SECTION BELT AUTOMATION SERIES END DRIVE V-GUIDE TIE BAR EXTENDED FRAME CONVEYORS ANCHOR BAR SCREW SOCKET HEAD CAP M6x1.0 10mm LG. ZP ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

18"-24" Wide Auto. Series Extended Conveyor Center Drive with Standard Belt LEGEND 2

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MAE

Item 1 2 3 4 5 6 7 8 9 10

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1A0047A 1A0047A AC6-WW-LLL-MAE 1D0226A PHCS-M06X100X018-ZP-ST PHCS-M06X100X025-ZP-ST 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL ASSY MULTI-PIECE FRAME EXTENSION SECTION ASSY MULTI-PIECE FRAME DRIVE SECTION BELT AUTOMATION SERIES END DRIVE STANDARD TIE BAR EXTENDED MULTI-PIECE FRAME CONVEYORS SCREW SELF TAPPING PAN HEAD M6x1.0 18mm LG. ZP SCREW SELF TAPPING PAN HEAD M6x1.0 25mm LG. ZP ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

18"-24" Wide Auto. Series Extended Conveyor Center Drive with V-Guide Belt LEGEND 3

Location on Parts List Part not sold separately

PART# AC61HWW-LLL-LEF-MVE

8 10

Item 1 2 3 4 5 6 7 8 9 10

Part No.

1A0044AWWWW 1A0039AWWWW 1A0038AWWWW 1A0047A 1A0047A AC6-WW-LLL-MVE 1D0226A PHCS-M06X100X018-ZP-ST PHCS-M06X100X025-ZP-ST 1A0073AWWWW

Description

Item

Part No.

Description

ASSY CENTER DRIVE FIXED END IDLER ASSY TAIL V-GUIDED ASSY TENSION RELEASE TAIL ASSY MULTI-PIECE FRAME EXTENSION SECTION ASSY MULTI-PIECE FRAME DRIVE SECTION BELT AUTOMATION SERIES END DRIVE V-GUIDE TIE BAR EXTENDED MULTI-PIECE FRAME CONVEYORS SCREW SELF TAPPING PAN HEAD M6x1.0 18mm LG. ZP SCREW SELF TAPPING PAN HEAD M6x1.0 25mm LG. ZP ASSY CENTER DRIVE PACKAGE

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

Automation Series AS65 Center Drive Package Assembly LEGEND 5

Location on Parts List Part not sold separately 1A0073AWWWW

6 16

18 7 14

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Part No.

1D0035A 1D0051A 1D0031A 1D0048AWWWW 1D0057A 1D0130A 1D0049AWWWW 1D0050A 1D0052A 1A0043AWWWW 1D0109A 1D0116A 1D0170A

Description

PLATE, CENTER DRIVE, NON-DRIVE SIDE PLATE, CENTER DRIVE, MOTOR MOUNTING ANCHOR BAR, CENTER DRIVE MTG PULLEY, CENTER DRIVE BEARING, CENTER DRIVE, SQUEEZE LOCK STYLE KEY, 6mm SQUARE x 19mm LG. GUARD, CENTER DRIVE CONV. BELT DRIVE COVER, CENTER DRIVE CONVEYOR COVER, BEARING, CENTER DRIVE, NON DRIVE SIDE ASSY CENTER DRIVE IDLER BLOCK, JACKING SCREW SQUARE HEAD M6 X 20 MM LG PIN, DOWEL, HARDENED, 6 OD X 12 LG BHCS-M05X080X010-ZP SCREW BUTTON HEAD CAP M5 X 0.8 X 10 LG ZP

Item 15 16 17 18 19

Part No.

Description

FHCS-M05X080X025-ZP

SCREW FLAT HEAD CAP M5 X 0.8 X 25 LG. ZP SCREW FLAT HEAD CAP M6 X 1.0 X 16 LG. ZP SHCS M04X070X025-ZP SCREW SOCKET HEAD CAP M4 X 0.7 X 25mm ZP SHCS M04X070X050-ZP SCREW SOCKET HEAD CAP M4 X .7 X 50mm ZP SHSS-M08X125X050-BX-B SCREW SOCKET HEAD SET FHCS-M06X100X016-ZP

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Automation Series Tail Pulley Assembly LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0039AWWWW 4

Item 1 2 3 4 5

Part No.

Description

1D0157AWWWW 1D0158AWWWW 1D0132A 1D0121A SHDSS-M08X125X030-BX-B

Item

Part No.

Description

TAIL PULLEY TAIL SHAFT BEARING RETAINING RING SCREW SOCKET HD. SET DOG PT. M8x1.25 30mm LG.

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

Automation Series Center Drive Fixed End Assembly LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0044AWWWW 6

9 10 1 7 12 11

4 2

Item 1 2 3 4 5 6 7 8 9 10 11 12

Part No.

1D0034AWWWW 1D0064A 1D0065A 1D0080A 1D0116A 1D0124A 1D0125A 1D0126A 1D0131A SHCS-M06X100X010-ZP SLHCS-M6X100X010-BX 1D0285A

Description

Item

Part No.

Description

PULLEY, CENTER DRIVE, FIXED END IDLER DRIVE BEARING HOUSING LH DRIVE BEARING HOUSING RH ANCHOR BAR BEARING HOUSING SCREW JACKING SQ. HEAD M6x1.0 20MM LG. ANCHOR BAR JACKING BLOCK BLOCK JACKING LH DRIVE END BLOCK JACKING RH DRIVE END BEARING AUTOMATION SERIES DRIVE END SCREW SOCKET HEAD CAP M6x1.0 10MM LG. SCREW SOCKET LOW HEAD CAP M6x1.0 10MM LG. SCREW SOCKET HD. SET M4x0.7 5MM LG w/NYLOK

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Automation Series Tension Release Tail Assembly LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0038AWWWW 12 8

5 4

Item 1 2 3 4 5 6 7 8 9 10 11

Part No.

Description

1D0181A 1D0182A 1D0172AWWWW 1D0292A 1D0164A 1D0165A 1D0168A 1D0225A SHSS-M06X100X006-ZP FHCS-M02.5X045X005-BX SLHCS-M05X080X010-ZP

Item

Part No.

Description

TAIL PLATE RH TAIL PLATE LH TAIL STIFFENER ANCHOR BAR/TAIL SPRING/DOWEL PIN TAIL BUTTON BUTTON RETAINING PLATE BUSHING BUTTON HEAD SHOULDER SCREW SCREW SOCKET HEAD SET M6x1.0 6mm LG. SCREW SOCKET FLAT HEAD M2.5x0.45 5mm LG. SCREW SOCKET LOW HEAD CAP M5x0.8 10mm LG.

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

Automation Series Tail Pulley Assembly LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0039AWWWW 4

Item 1 2 3 4 5

Part No.

1D0157AWWWW 1D0158AWWWW 1D0132A 1D0121A SHDSS-M08X125X030-BX

Description

Item

Part No.

Description

TAIL PULLEY TAIL SHAFT BEARING RETAINING RING SCREW SOCKET HEAD SET DOG PT. M8x1.25 30mm LG.

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Automation Series 2" - 6" Wide Stub Underside Idler Assy LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0040A

3 2

5 1

Item 1 2 3 4 5 6

Part No.

Description

1D0152A 43-0050-51 43-0050-52 1D0151A 1D0148A SHCS-M05X080X016-ZP

Item

Part No.

Description

SHAFT STUB UNDERSIDE IDLER 2" - 6" BEARING UNDERSIDE IDLER STUB RETAINING RING CLAMP UNDERSIDE IDLER STUB GUARD UNDERSIDE IDLER STUB 2" - 6" SCREW SOCKET HEAD CAP M5x0.8 16mm LG.

4057 Clough Woods Dr. |Series Batavia, 45103 Maintenance, | (513) 753-6000 | Manual Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation AS65OH Installation, and Parts

Automation Series 8"-24" Wide Full Width Underside Idler Assy LEGEND 5

Location on Parts List Part not sold separately

PART# 1A0042AWWWW

3 8

Item 1 2 3 4 5 6 7 8

Part No.

Description

1D0215AWWWW 1D0155AWWWW 1D0208A 1D0147AWWWW 1D02040A 43-0050-52 SHCS-M05X080X016-ZP SHSS-M05X080X010-BX

Item

Part No.

Description

SHAFT UNDERSIDE IDLER FULL WIDTH ROLLER UNDERSIDE IDLER FULL WIDTH CLAMP UNDERSIDE IDLER FULL WIDTH GUARD UNDERSIDE IDLER FULL WIDTH BEARING UNDERSIDE IDLER FULL WIDTH RETAINING RING SCREW SOCKET HEAD CAP M5x0.8 16mm LG. SCREW SOCKET HEAD SET M5x0.8 10mm LG.

4057 Clough Woods Dr. | Batavia, OH 45103 | (513) 753-6000 | Fax: (513) 753-6001 | www.qcindustries.com QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.09 Recommended Spare Parts QC Industries recommends that the following items be stocked as spares to minimize downtime and ensure optimum performance of your Automation Series conveyor (Figure 1): Part # 1A0039AWWWW 1A0043AWWWW AC6-WW-LLL-MAE 1D0057A 1A0034A 1A0035A 1A0033AWWWW 1A0036A C-0117-XXX

Description Tail Pulley Assembly Center Idler Pulley Assembly Standard Urethane Belt, (MVE for V-Guided) Center Drive Bearing Fixed End Bearing Housing w/Bearing LH Fixed End Bearing Housing w/Bearing RH Underside Idler Roller Full Width (if necessary) Underside Idler 2”-6” Wide Stub Roller (if necessary) Drive Timing Belt (090 for drives with ≤ 50 sprocket teeth, 100 for drives with ≥ 52 sprocket teeth)

STANDARD: 1A0034A LH Drive End Bearing Housing w/Bearing. Bearing ONLY: 1D0131A

STANDARD: 1A0039AWWWW Sealed Tail Assy

STANDARD: 1A0036A 2”-6” Wide Stub Roller

STANDARD: 1D0057A Center Drive Bearing

STANDARD: 1A0043AWWWW Center Drive Idler Pulley Assy STANDARD: 1A0035A RH Drive End Bearing Housing w/Bearing. Bearing ONLY: 1D0131A

STANDARD: 1A0033AWWWW Full Width Underside Idler Roller

STANDARD: AC6-WW-LLL-MXE MAE: Standard urethane Belt MVE: Standard V-Guided Belt Figure 1

To build a width dependent assembly’s part number, use the 4-digit width of the conveyor for “WWWW”. Similarly, to build a Belt’s part number, use the width and 3-digit length of the conveyor for “LLL”. Belt Part Number example: A

“MAE” refers to the Standard Urethane Belt. Refer to the QC Industries Product Catalog for other belt types and designations available. To order spare belts or replacement parts, please contact QC Industries Customer Service department at (513) 753-6000.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

3.10 Troubleshooting Note: if you are unable to remedy the problem with these corrective actions, please contact QC Industries Customer Service at (513) 753-6000. Failure to correct the problem may lead to abnormal use of the conveyor, thereby voiding the warranty.

Symptoms

Possible Cause

Corrective Action

Belt is slipping or stops under load

Application demand is more than the conveyor is rated for

Verify the conveyor’s capacity for the application

Lubrication between drive pulley and belt Clean bottom of belt and drive pulley Tail Pulley assembly not tensioned properly.

Refer to Section 3.03 Figure 8

Timing Belt under drive guard is not connected

Verify correct installation

Tail Pulley assembly not tensioned properly.

Verify that tail pulley is in correct position as instructed in Section 3.03 Figure 8

Belt will not track at Drive End

Accumulation; belt wear

Track the belt as instructed in Section 3.02

Belt will not track at Tail End

Belt wear; irregular product loading

Track the belt as instructed in Section 3.02

Belt does not move without load

Belt is becoming brittle Belt is being attacked by chemicals or or delaminating excessive heat

Contact factory to discuss application parameters for proper belt selection

Belt’s useful life has expired

Replace the belt

Belt is discoloring

Urethane Belts are subjective to discoloration when exposed to UV light

None

Motor is hot

Normal operation - motor can run with a None skin temperature of 221°F under normal conditions

Speed Reducer is hot

Motor is not protected with overload protection and is drawing too much current

Install overload protection on the motor; or use bigger motor/different gearbox ratio

Normal operation – speed reducer can run with a skin temperature of 225°F under normal conditions

None

Initial installation not performed correctly Purchase a new speed reducer and follow manufacturer’s installation instructions and speed reducer input shaft is carefully damaged Bearing Noise

Bearings are damaged or failing

Replace bearings

Motor or speed controller not wired Belt is traveling the reverse of the desired properly direction

Check wiring, correct per wiring instructions

Conveyor belt has prematurely worn out

Contact factory to discuss application parameters for proper belt selection

Correct belt not selected for the application parameters

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

4.01 Conveyor Serial Number The conveyorâ&#x20AC;&#x2122;s serial number is located on the Center Drive Mounting Plate opposite the drive side (Figure 1).

Drive Side

Opposite Side

Serial Number Location

Figure 1

Record the serial number in a place where it can be accessed for reference; a place has been provided on the back cover that can be used for multiple conveyors. This will assist any future inquires regarding the conveyor, its accessories, the order it was shipped on, or replacement parts.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

4.02 Conveyor Warranty QC INDUSTRIES warrants that our conveyors are free from defects in materials and workmanship and fit for the ordinary purposes for which such goods are used, under normal installation, use and service for five (5) years from date of purchase or 10,500 hours of running use, whichever is sooner. QC INDUSTRIES will replace any defective part within the warranty period, without charge, provided: (1) (2) (3) (4)

The Purchaser gives QC INDUSTRIES prompt written notice of the defect, including the date of purchase and original purchase order number. The Purchaser will then be given a return goods authorization number (RGA#) which must be displayed on all labels and packing slips returned with merchandise. (See RGA section) The Purchaser pays for delivery of the defective part to QC INDUSTRIES for inspection and verification of the defect. The Purchaser shall pay all shipping and insurance charges for the replacement part from QC INDUSTRIES and the cost of installing the replacement part.

This warranty is limited to the replacement of defective parts. QC INDUSTRIES WILL NOT BE LIABLE FOR ANY DAMAGES CAUSED BY ANY DEFECT IN THIS UNIT. This warranty shall not apply if any failure of this unit or its parts is caused by unreasonable use, lack of maintenance, improper maintenance and/or repairs, incorrect adjustments, exposure to corrosive or abrasive material, moisture causing damage, or any modification or alteration affecting the operation of the unit which is not authorized by QC INDUSTRIES in writing. This warranty shall not apply to the following items that are covered by their manufacturer's warranty, subject to any limitation contained in those warranties. (A) (B) (C)

Bearings Motors Reducers

(D) (E) (F)

Controllers Casters Belts (unless otherwise agreed to in writing)

CAUTION: Any attempt to repair such items may actually void the manufacturer's warranty. Any description of this unit is only to identify it and is not a warranty that the unit fits the description. Only an official of QC INDUSTRIES may make any warranties for QC INDUSTRIES. Any warranties implied by law are limited in duration to the five (5) year term of this warranty. EXCEPT AS SET FORTH HEREIN, QC INDUSTRIES MAKES NO OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING MERCHANTABILITY FOR FITNESS OR ANY PARTICULAR PURPOSE.

Lost or Damaged Goods Shipments should be inspected immediately upon receipt for lost or damaged goods. Any loss or damage should be noted on the carriers receipt (or bill of lading) at the time of acceptance. If items are perceived to be lost or damaged after the shipment has been accepted, it becomes more difficult to file a claim with the carrier if the receipt does not indicate such loss or damage. Do not, at any time, request the carrier to return any items or shipment to QC Industries without previous authorization from our company for such a return. Please notify QC Industries as soon as any loss or damage is discovered and request the department that handles the lost or damaged goods. You will need to know a complete description of all lost or damaged items. If replacement items are needed, a purchase order made out to QC Industries will need to be supplied. QC Industries will then contact the carrierâ&#x20AC;&#x2122;s local agent and request that an inspection of the items be performed. This is absolutely necessary. Unless an inspection is performed, the carrier will not entertain any claim for loss or damage. After the inspection has been completed, the carrier will notify QC Industries. If the carrier takes responsibility for the claim, a credit will be issued to you for the replacement item(s), including freight charges from QC Industries, where applicable. If the carrier does not take responsibility for the claim, a representative of QC Industries will contact you.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

4.03 Returns If, for any reason, an item needs to be returned to QC Industries or an in-house order needs to be canceled or revised, the Purchaser is required to adhere to the following series of steps to ensure that the return or cancellation is handled in the proper manner. RGA Policy/Instructions: (1)

(2) (3)

(4) (5)

Promptly call QC Industries Customer Service at (513) 753-6000 and request a Returned Goods Authorization. At this time, you will be asked to answer pertinent questions relating to the returned items. We ask that you have the following information ready: (A) Name of distributor (if applicable) through which item(s) were purchased. (B) Name of the Customer and/or end user of the item(s). (C) Any/all purchase order numbers related to the item(s) in question. (D) Phone numbers and names of contacts involved in the return (if it becomes necessary that they be contacted later). (E) Complete part numbers of all items involved in the return. (F) Complete description as to the reason for the return and the actions that need to be taken. (If the item is to be replaced, a new purchase order number must be supplied by the Purchaser along with complete shipping and billing instructions. These replacements will be treated as separate orders by QC Industries and evaluated for possible credit only after returned items are received and evaluated. After the call is made to QC Industries, we will process your RGA and you will be faxed the RGA number to use for returning the item(s). RGA numbers will not be given verbally over the phone. Upon receipt of your RGA, you are required to return the item(s) within 30 days of receipt of authorization. After 30 days, the Return Authorization will be void if item(s) are not received by QC Industries. All shipping charges and freight insurance charges of returned goods will be the responsibility of the Purchaser. The RGA number must be clearly marked on the outside of all packages. It must also be on any paperwork, packing slips, or delivery receipts. If there is no RGA number visible on the package, the package may be refused and sent back at the Purchaser's expense. After receipt of returned goods, QC Industries will evaluate the item(s) for credit and take the appropriate action. Standard items that are returned in new, resalable condition will be credited for the amount of the purchase less 20%. Full credit will only be issued on items that are considered to be defective at the time of shipment from QC Industries and are evaluated to be under warranty. Please allow 30 days for credits to be issued.

Order Cancellation / Revision Policy If it becomes necessary to cancel or revise an order prior to the order being shipped, QC Industries reserves the right to evaluate each order that is to be canceled or revised and determine if any charges are applicable. A 20% restocking charge will apply if an order is assembled and ready to ship prior to its cancellation or revision and the order is totally comprised of standard stock items. If the order contains other than stock items, an evaluation will be made based on the status of the order. Additional charges will be included with the 20% restocking charge if any of the following conditions are met: (A) The order contains any items that are considered to be non-stock items and these items have already been produced by QC Industries or one of its suppliers. (B) The order contains any items that require special handling or assembly and these processes have been completed. (C) The Customer has specified that they will pick-up an order from QC Industriesâ&#x20AC;&#x2122; facility by a predetermined time and that time frame has expired. In this case, QC Industries will make an attempt to notify the Customer. If this cannot be accomplished in a reasonable time, the order will be disassembled and the Customer will be charged a restocking fee and any additional charges based on the orders contents as explained herein.

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

Notes:

QC Industries Automation Series AS65 Installation, Maintenance, and Parts Manual

For future reference, record the date, part number and serial number for each conveyor in your order. Date

Part Number

Serial Number

Additional Conveyor Products from QC Industries

125 Series Belt Conveyors • Available in four styles: • Automation • Corrosion Resistant • Cleated • Magnetic • Less than 5minute belt change • Widths up to 24”, lengths up to 25’

125Z Series Angled Frame

Flextrac Plastic Chain

InnerDrive Conveyors

• Available in five configurations • Five standard angles: 30°, 60°, 45°, 75°, 90° • Patent-pending Z-Track™ simplifies belt tracking and locks in adjustments — even through belt changes

• Low 3.03” profile • High speeds – up to 375 fpm – and heavy loads – up to 500 lbs. • More than 100 belt type and material combinations • Partial belt changes reduce maintenance costs

• Save space by moving the motor inside the conveyor frame • Safe, efficient 24vdc motor • Low profile design • Variable speed control card easily integrates with “run-on-demand” applications

For more information, visit our website — www.qcindustries.com — or contact a member of our knowledgeable sales staff at (513) 753-6000. Part No.: MKTG-MAN-250-08.08.0.ONLINE