IQ3RZR
DASH KIT
Q U I C K S TA R T G U I D E
WHAT’S IN THE BOX
IQ3 RZR DASH AND MOUNT PANNEL
FOR TECHNICAL ASSISTANCE 949-709-5555
IQ3 MOUNTING HARDWARE
IQ3 PROGRAMMING CABLE AND USB TO SERIAL ADAPTER
GPS ANTENNA
IQ3 RZR HARNESS WITH BUTTONS
IQ3 PROTECTIVE COVER
SOFTWARE MEMORY STICK
IQ3 DASH / REAR OVERVIEW
A. GPS ANTENNA CONNECTOR Provides connection for external GPS antenna B. VNET CONNECTOR Provides input for additional VNet (CANbus) sensors and extension cables
E
A
B
C
C. DEUSTCH 8 PIN CONNECTOR Provides input for power / ground / Polaris Data / programming buttons IQ3 dash requires 12-18 v power supply D. SERIAL CABLE CONNECTOR Provides input for serial programming cable supplied with package E. MOUNTING HOLES Three #10 studs and 10-32 nuts facilitate mounting
BACK SIDE
D
STEP 1 / FACTORY DASH REMOVAL
1. Hood Removal
FOR TECHNICAL ASSISTANCE 949-709-5555
2. Dash Removal
3. Headlamp Switch / AWD/2WD Switch
To remove the hood, turn both 1/4 turn
Remove the two T-40 Torx screws retaining
Disconnect the headlamp and AWD/2WD
latches to disengage the rear portion of the
the Upper Dash cover between the front
switch harnesses by depressing the
hood. Lift rear of hood and slide forward to
fenders.
connector locks and pulling on the
disengage the front tabs and remove the hood from the vehicle.
connector. Do not pull on the wiring.
STEP 1 / FACTORY DASH REMOVAL
4. Ignition (Key) Switch
5. Instrument Gauge
6. 12 Volt Accessory Outlet
Disconnect the key switch harness by
Disconnect the instrument gauge harness
Disconnect the two small wires on the 12
depressing the connector lock and pulling
by depressing the connector lock and
volt accessory outlet by pulling on each of
on the connector. Do not pull on the wiring.
pulling on the connector. Do not pull on
the connectors. Do not pull on the wiring.
the wiring.
STEP 2 / IQ3 RZR DASH INSTALL
1. IQ3 Dash
FOR TECHNICAL ASSISTANCE 949-709-5555
2. Button Installation
3. Reinstall factory switches
Fasten IQ3 Dash to the new Mount Panel
Install the two Racepak programming
Install ignition key switch, AWD/2WD switch,
using supplied hardware.
buttons, black on the left and red on the
headlight switch and 12 volt accessory outlet
right, in relation to the driver’s position
into pre-cut holes provided in the Racepak
viewing the dash.
upper dash mount.
STEP 2 / IQ3 RZR DASH INSTALL
4. Connection of the GPS antenna
5. IQ3 RZR harness
6. Connect Instrument Gauge Harness
Upon completion of mounting of the antenna,
Plug the 8-pin Deustch connector in the
Plug the Racepak molded connector into
simply route the cable to the rear of the IQ3
appropriate port on the rear of the IQ3
the factory gauge harness. Using the supplied
RZR Dash and connect to the GPS antenna
dash.
ring terminal, terminate and connect the
port. Ensure the cable end is screwed tightly
black ground wire exiting from the button
to the GPS connector. Excessive force when
harness.
being tightened can damage the connector, resulting in failure of GPS signal reception.
FOR TECHNICAL ASSISTANCE 949-709-5555
7. Dash Installation
8. Hood Installation
9. All done!
Insert dash panel from passenger
Insert the hood from the front to engage the
Power up your dash by turning on the
compartment. Install and tighten the two
front tabs. Press down on the rear portion
ignition. This will allow you to instantly
T-40 Torx screws to secure the Upper Dash
of the hood and turn both 1/4 turn latches
access the first of the four display pages
cover between the front fenders.
to engage the rear lock down holes in the
available on your IQ3. Slip the IQ3 protective
dash panel.
cover over the IQ3 dash. This cover is designed to provide a snug fit, but you may choose to further secure the cover by using an adhesive like silicone.
IQ3 DASH / FRONT OVERVIEW A
A. STATUS LIGHTS Pre-set Status Lights for high beam, neutral, FWD, Steering MIL, and Engine MIL B. WARNING LIGHTS 1 & 2 Pre-set warning lights for Fuel Level and Water Temperature
B
C D
C. WARNING LIGHTS 3 & 4 Fully programmable warning lights for Inputs 3 & 4
E
D. GEAR POSITION E. CHANNEL LABEL 5 character programmable alpha/ numeric text per display channel F. BLACK (LEFT) PROGRAMMING BUTTON The black (left) button is to advance to the next display page G. RED (RIGHT) PROGRAMMING BUTTON The red (right) button is used to clear warnings on the dash
FRONT SIDE
F
G Please consult the IQ3 RZR manual for complete details on the functions of these buttons.
IQ3 DASH / FACTORY DEFAULT DISPLAY SETTINGS
1 2
The first display (default) page is programmed by the factory to display: • Engine Speed (swept tach) • Wheel Speed • Gear Position • Fuel Level • Water Temperature • Heading • Time
By pressing the left (black) button, you can advance to the second pre-programmed page which will display: • Engine Speed (swept tach) • GPS Speed • Gear Position • Satellites • Altitude • Fuel Economy • Voltage
If you wish to customize any of the display please refer to Step 3 / Configure Your Dash in this Quick Start Guide.
FOR TECHNICAL ASSISTANCE 949-709-5555
3 4
The third pre-programmed page displays: • Engine Speed (swept tach) • Service Hour Meter • Gear Position • Odometer • Total Hour Meter • Belt Hour Meter • Trip Odometer
The fourth pre-programmed page displays: • Engine Speed (swept tach) • Oil Pressure* • Gear Position • Belt Temperature* • Oil Temperature* • Water Temperature • Boost Pressure*
*Please contact Racepak for these optional accessory kits at 949-709-5555
STEP 3 / INSTALLING ADDITIONAL SENSORS OPTIONAL - IF NO ADDITIONAL SENSORS PROCEED TO STEP 4
1. Start the DataLink software. 2. Connect the programming cable between the Racepak IQ3 in the Razor and your PC. 3. Apply power to the Racepak IQ3.
When installing new sensors or items on the V-Net system, you must update/ sync the configuration file in your PC to ensure that any changes and/or updates performed on your Racepak system will properly take affect. Carefully follow the instructions below to perform the configuration update.
4. Select File from the menu bar then select Open Car Configuration.
5. Select the IQ3_Config_UTV_Display and click on the OK button.
FOR TECHNICAL ASSISTANCE 949-709-5555
6. Select Edit from the menu bar then select Read V-NET Config.
7. Click on the OK button when you see the message “Devices Read Successfully�. If you receive an error at the beginning of this step, verify that you are set on the COM port that matches the port that the cable is installed on.
8. Select File from the menu bar and select Save. 9. Turn off the power to the Racepak IQ3 and disconnect the serial cable.
STEP 4 / CUSTOMIZE DISPLAY PAGES
1. Start the DataLink software. 2. Connect the programming cable between the Racepak IQ3 in the Razor and your PC. 3. Apply power to the Racepak IQ3.
4. Select File from the menu bar then select Open Car Configuration.
5. Select the IQ3_Config_UTV_Display and click on the OK button.
FOR TECHNICAL ASSISTANCE 949-709-5555
6. Right-click IQ3 UTV
7. Select box representing desired location.
11. Click Send Configuration. When done
8. Select ID to be displayed.
programming your dash, close the
9. Set decimal point and 5 character label tag.
Racepak software and save changes to
10. Click OK.
the IQ3 configuration file when prompted. You may also choose to save the file by selecting File from the menu bar and then selecting Save.
W W W. U T V R A C E PA K . C O M