© 2019
Modified RE-9084 w/ RE-1227 & RE-1207
20’
Plan View
20’
© 2019
Grid View
= 1 sq foot
Š 2019
General Information
General Setup Instructions 7A
- Read entire setup instruction manual prior to unpacking parts and pieces. - The setup instructions are created specifically for this configuration. - Setup instructions are laid out sequentially in steps, including exploded views with detailed explanation for assembly.
Hex Tool - Essential for Assembly
WARNING
Part Identification - Numbering
Cleaning & Packing
DO NOT USE POWER TOOLS
- For Cleaning Metal, Plex, & Laminate Parts: Use a MILD NON-ABRASIVE cleanser and soft cloth/paper towel to clean all surfaces. - Keep exhibit components away from heat and prolonged sun exposure. Heat and UV exposure will warp and fade components.
LADDERS OR LIFTS MAY BE REQUIRED Spline Connection
Base Plate & Extrusion Connection
- Retain all provided Packing Materials. All provided packing materials are for ease of repacking & component protection.
ALL CONNECTIONS MUST BE TIGHTLY SECURED
Disassembly - For loss prevention, tighten all set screws and locks during disassembly.
Extrusion & Lock Connection
Engaged Lock
Š 2019
Gravitee Assembly
Assembly
Assembly Cont’d Push pin lock into hole of connecting frame. Note: Block of pin lock will secure in groove.
Side-by-Side Assembly
Corner Connector
1) Frames: Place frames side-by-side with one higher than the other, then slide panel down to lock panels securely together.
SEG Grooves
2) Corner Connectors: Repeat Step 1 for installing corner connectors to frames.
Side-by-Side Disassembly
Pin Lock
1) Pull pin lock outwards to disengage. 2) Pull frames upward and apart at the same time to detatch.
Stacking
Stacking Assembly 1) Place one horizontal frame on top of the other, lining up the center grooves.
Unstacking
Push stacking lock into the slot of the upper frame, then spin the cap to tighten the lock.
2) Turn stacking lock clockwise to tighten into place. Repeat for each lock.
Stacking Disassembly 1) Turn the stacking lock counter-clockwise to loosen. 2) The whole spring on the stacking lock should be in view to release each frame. The disengaged spring should release the stacking lock. If not, keep turning the stacking lock until it disengages.
Top View
Note: Orientation of Corner Connector may change.
Stacking Lock
Cap
Disengage the stacking lock by spinning the cap counter clockwise and pulling down.
Š 2019
CEI152 Frame Assembly
Corner Bracket Installation 1) Slide TWO-PIECE TS RV 2 L-bracket into Interior Center Slot of extrusion so that two set screws are inside groove. Tighten two set screws to secure. 2) Slide two A1 L-Brackets into outer interior grooves of upper and lower horizontals. Tighten set screws to secure. 3) Slide vertical extrusion over exposed ends of brackets in lower horizontal. Tighten set screws to secure. 4) Slide exposed ends of installed brackets of upper horizontal into open ends of verticals. Tighten set screws to secure.
Corner Connection Upper Horizontal
A1
Upper Horizontal
A1
Slide verticals over brackets of lower horizontal, then slide upper horizontal & brackets into grooves & center slots of verticals.
TS RV 2 Insert L-Brackets into the Interior Center Slot & outer interior grooves of extrusion.
Lower Horizontal
TS RV 2
Disassembly
Completed Assembly
A1
Straight Connection
Straight Bracket Installation 1) Slide TWO-PIECE TS RV 4 straight bracket into Interior Center Slot of extrusion, so that two of the set screws are inside groove. Tighten two set screws to secure. 2) Slide two V4 Connectors into outer interior grooves of extrusion, so that one set screw is inside groove. Tighten set screw.
Lower Horizontal
A1
1) Loosen set screws on brackets and slide extrusions off of brackets.
12 Brackets Total: (4) - TS RV 2 (8) - A1 L-Brackets
Insert two-piece bracket into the interior center slot of extrusion.
TS RV 4 Bracket
CEI-152 Profile
V4
3) Slide connecting extrusion over exposed ends of bracket & connectors. Tighten all remaining set screws to secure extrusions. Set Screws
Slide connecting extrusion over exposed ends of bracket & connectors.
V4
Slide V4 Connectors into front & back interior grooves.
Secure inserted half of bracket & connectors using set screws.
Completed Assembly Secure extrusion, using remaining set screws.
Š 2019
SEG Installation
Corner A
Corner B
Corner D
Corner C
It is important to first insert graphic into each alternate corner then to the sides of the frame. If this is not done, graphic will not fit into the frame correctly.
Graphic Removal
Step 1 Insert corner A. Turn edge of graphic so silicon welt is perpendicular to face of graphic. Insert narrow side of welt with fabric to outside into the channel. Repeat for other side of this corner.
Step 2 Repeat Step 1 for opposite corner C, then insert corner B, followed by corner D, to complete the installation of the corners.
Step 3 Once all corners are inserted, press one silicon edge into channel from corners and work toward the center. Make sure welt is fully inserted into channel. Continue until all sides are done. Smooth out edges of graphic.
To remove the graphic from the frame, locate the fabric pull tab. Gently pull up on the tab to remove the fabric.
© 2019
Closet Assembly
Item 1 2 3 4 5 6 7 8 9 10 6/6A
Qty. 1 1 1 1 1 1 1 1 1 1 1/1
Description 94.5”h Gravitee Corner Post w/ caps 46”w x 95”h Gravitee Panel 46”w x 95”h Gravitee Panel 94.5”h Gravitee Corner Post w/ caps 38”w x 95”h Gravitee Panel 94.5”h Gravitee Corner Post w/ caps 46”w x 95”h Gravitee Panel 46”w x 95”h Gravitee Panel 94.5”h Gravitee Corner Post w/ caps 38”w x 95”h Gravitee Panel w/ Door 91.904”h S44 Vertical Extrusion
Steps: 1) Attach vertical [6] to Gravitee Panel [2], and connect veritcal [6A] to Gravitee Panel [3]. 2) Assemble Gravitee Panels & Connectors together in numerical order. Refer to Gravitee Side-By-Side Assembly instructions in the General Information pages.
Profile View SEG grooves
6 5 4
Profile View
7
8
3
2
6A
SEG grooves
9 1
When assembled
10
6
SEG grooves
Profile View SEG grooves
Profile View
Keep internal extrusions attached to Gravitee panels. DO NOT REMOVE.
5.46”
5.46”
Step 1 of 7
© 2019
Closet Assembly (cont’d)
Item 1 2 3 4
Qty. 1 1 1 1
Description 47”h Gravitee Corner Post w/ caps 46”w x 47.5”h Gravitee Panel 46”w x 47.5”h Gravitee Panel 47”h Gravitee Corner Post w/ caps
Steps: 1) Assemble upper Gravitee Panels & Connectors [1-2-3-4] to lower panels & to eachother. See Gravitee Stacking Connection detail.
4
3
2
1
When assembled
*
4
*
3
Gravitee Stacking Connection
Push stacking lock into the slot of the upper frame, then spin the cap to tighten the lock.
*
*
2
*
1
Stacking Lock
Cap
Step 2 of 7
Š 2019
Closet Attachments
Steps: 1) Apply SEG graphics to closet assembly, as shown. 2) Attach Sintra Graphic to Door panel [10]. 3) Affix Sintra panel to Panel [5], using Velcro 3) Install Monitor Mount to verticals [6,6A] of panels [7,8]. See Monitor Mount Attachment detail. 4) Attach Lights to closet assembly. See Light Attachment detail.
*
Light Attachment
Lock Clip into Groove of Horizontal Extrusion then slide Light onto Clip.
Light
Clip
Light
Clip
Extrusion
SEG Graphic Installation Corner A
Corner B
*
*
SEG Graphic
* SEG Graphic
* *
Monitor Mount Attachment V4 Connectors Stand-Off Barrel
*
SE
G
Gr
ap
hic
Caps
*
Monitor Mount
10 tra Sinphic a Gr
or Doill Inf
Slide V4 Connections into vertical channel of extrusions. Tighten set screw to secure.
Profile View
Attach Stand-off Barrels to V4 Connectors then install Monitor Mount to stand-off barrels. Note: Monitor mounts install over SEG graphic.
Profile View
Graphic
Wrap back graphic around corner of post.
SEG Graphic
Graphic
Wrap back graphic around corner of post.
Corner D
Corner C
It is important to first insert graphic into each alternate corner then to the sides of the frame. If this is not done, graphic will not fit into the frame correctly.
Step 1 Insert corner A. Turn edge of graphic so silicon welt is perpendicular to face of graphic. Insert narrow side of welt with fabric to outside into the channel. Repeat for other side of this corner.
Step 3 Once all corners are inserted, press one silicon edge into channel from corners and work toward the center. Make sure welt is fully inserted into channel. Continue until all sides are done. Smooth out edges of graphic.
Step 2 Repeat Step 1 for opposite corner C, then insert corner B, followed by corner D, to complete the installation of the corners.
5
SEG Graphic
tra Sinnel Pa
Graphic Removal
To remove the graphic from the frame, locate the fabric pull tab. Gently pull up on the tab to remove the fabric.
BACK VIEW
Step 3 of 7
© 2019
Lightbox Assembly
Item 1 2/2A 3/3A 4/4A 5 --
Qty. 6 3/3 3/3 3/3 3 3
Description Base Plate 36”w CEI152 Horizontal Extrusion 90”h CEI152 Vertical Extrusion 90”h CEI152 Vertical Extrusion 32.338”w Z45 Horizontal Extrusion U-Channels
*
2A
*
*
Corner Base Plate Attachment
wing nut
Steps: 1) Install U-Channel to horizontal [2]. See U-Channel Attachment detail. 2) Attach verticals [3-3A], [4-4A] together. See CEI-152 Straight Connection detail. 3) Connect horizontals [2,2A] between verticals. See CEI-152 Corner Connection detail. 4) Attach horizontal [5] between verticals as shown. 5) Install Base Plates to extrusions [2,3] & [2,4]. See Base Plate Attachment detail. 6) Connect power cords to Supernova lights as shown. Place transformers into U-Channel.
key hole
3A
*
bolts
Use bolts to connect U-Channel to V4 horizontal. connector
Lights
*
5
+ -
Male
*
set screws
-
TSRV2 Bracket
- Female 96W / 4 amp Transformer
1
* *
U-Channel
2
* * *
Hole for wire management
When assembled
QTY 3
4) Use Set screws to secure extrusions.
CEI-152 Straight Connection
Transformer
Light to Tranformer Attachment
Power
CEI-152 Corner Connection
1) Insert TSRV2 and A1 Brackets into milled groove of extrusion. 2) Slide connecting extrusion over exposed end of brackets. 3) Use Set screws to secure extrusions.
4
3
+ +
*
A1
U-Channel Attachment
Light to Light Attachment
bolt
Screws
*
4A bolt
Repeat steps 1 through 6 for other two lightbox assemblies.
Slide V4 connectors into top groove of horizontal extrusion. Tighten setscrews to secure.
bolt
Place key hole over bolt on vertical extrusion and slide down; secure with bolts & wing nuts.
TSRV4 Bracket
1) Insert TSRV4 Bracket into milled groove of Extrusion. 2) Slide connecting extrusion over exposed end of bracket.
Set Screws
3) Use Set screws to secure extrusions.
1
Step 4 of 7
© 2019
Modified RE-1227 Counter Assembly
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING COUNTERTOP (RE-1227)
Steps: 1) Assemble Counter Unit as shown. 2) Affix Sintra panels to front, sides & back, using Velcro.
COUNTER SIDE (RE-1227)
COUNTER FRONT (RE-1227) (SHIPS ASSEMBLED)
COUNTER BACK (RE-1227) (SHIPS ASSEMBLED)
Sintra panels Counter Back includes GS300 vertical extrusion for attachment to Lightbox. COUNTER SIDE (RE-1227)
Step 5 of 7
Š 2019
Lightbox Attachments
Steps: 1) Connect assembled Counter to side of lightbox frame, using Z45 horizontal extrusions, as shown in illustration. 2) Apply SEG Graphic to front & back of lightbox. Repeat steps 1 & 2 for other two lightbox assemblies. 3) Attach medium Monitor Mount to the front lightbox, above the attached Counter, as shown.. See Monitor Mount Attachment detail.
SEG Gr
SEG Graphic
aphic
*
Monitor Mount Attachment
Slide V4 connectors into vertical channel of extrusions. Tighten set screws to secure.
set screw
V4 Connector V4
* Monitor Mount Bolts
Monitor Mount
Attach Monitor Mount to V4 connectors using bolts.
Front Lightbox
SEG Graphic Installation Corner A
Corner B
Corner D
Corner C
It is important to first insert graphic into each alternate corner then to the sides of the frame. If this is not done, graphic will not fit into the frame correctly.
Z45
Z45
RE-1227 Counter
Step 1 Insert corner A. Turn edge of graphic so silicon welt is perpendicular to face of graphic. Insert narrow side of welt with fabric to outside into the channel. Repeat for other side of this corner.
Step 3 Once all corners are inserted, press one silicon edge into channel from corners and work toward the center. Make sure welt is fully inserted into channel. Continue until all sides are done. Smooth out edges of graphic.
Step 2 Repeat Step 1 for opposite corner C, then insert corner B, followed by corner D, to complete the installation of the corners.
Graphic Removal
To remove the graphic from the frame, locate the fabric pull tab. Gently pull up on the tab to remove the fabric.
Step 6 of 7
© 2019
Modified RE-1207 Counter Assembly Steps: 1) Assemble Counter Unit as shown. 2) Affix Sintra panels to front, sides & back, using Velcro.
RE-1207 Counter Top RE-1207 Side When assembled
RE-1207 Door
RE-1207 Center
Sintra panels
RE-1207 Front
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
RE-1207 Counter Top Supports
RE-1207 Side Step 7 of 7