www.reprap.cn
reprap@live.cn
机架组装 Frame assembly
上图为 huxley 全部 RP 零件，需用电钻进行修理扩孔 For all above Huxley RP parts, need electric drill repair reaming
M6 螺母 M6 垫片 M6 平垫 M6 nut M6 gasket M6 flat mat
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
组装 2 个这样的 3 角架 Assembly two such three Angle frame
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
According to the chart assembly 按图组装
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
The next step 进行下一步
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
对于轴承和轴套部分需要用热熔胶加固，防止松动. For bearing and shaft sleeve parts need to use hot melt adhesive reinforcement to prevent loosening.
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
像上图一样组装完成 Like as the complete assembly
运动小车板组装 The small moving plate assembly
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
轴承上用热熔胶加固 Bearing with hot melt adhesive reinforcement
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
T2.5 同步带长度为 600mm T2.5 synchronous belt length is 600 mm
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
Z 轴 限 位 座 和 电 源 开 关 安 装 The Z axis limit and power switch installation
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
X 轴电机安装 The X axis motor installation
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
X 轴皮带安装 The X axis belt installation
Z 轴螺杆安装，放入弹簧和 M5 螺母 Z axis screw installation, in the
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
spring and the M5 nut
Z 轴螺杆上头，需磨凹槽 Z axis screw top, grinding groove
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
www.reprap.cn
reprap@live.cn
放入 M3 紧定螺钉 In the M3 screw set
www.reprap.cn
reprap@live.cn
www.reprap.cn
X
轴
限
位
安
reprap@live.cn
装
The
X-axis
installation
www.reprap.cn
reprap@live.cn
limit
www.reprap.cn
reprap@live.cn
Y 轴限位组装 Y limit assembly
www.reprap.cn
reprap@live.cn