Bulletin 51.1:EW
March 1998
EW Series (Designs EWD/EWS/EWT) Sliding-Stem Control Valves through 10 x 8- & 12 x 8-Inch Sizes Design EW Description The EW Series easy-e valves (figures 1 through 5) feature large internal cavities with expanded end connections and a variety of unbalanced and balanced plug designs. Sizes available from 4 x 2(1) through 12 x 8 inches include 8 x 6 with 10-inch ends and 10 x 8 inch sizes. These combinations provide good fluid control in economical, high-capacity valve bodies that keep valve outlet velocities within practical limits. These valves meet a variety of service requirements, such as power plants where oversized piping is used to limit fluid flow velocity. They also perform well in noise abatement applications; for example, high-pressure gas reducing stations where sonic velocities are often encountered at the outlet of conventional valve bodies.
The easy-e Valve Family EW Series valves are part of the versatile easy-e family of industrial control valves from Fisher Controls. easy-e valves share the following characteristics: Multiple trim material choices
Interchangeable, restricted-capacity trims and full-size trims to match variable process flow demands Different cage/plug styles that provide particular flow characteristics for highly-specialized applications. The standard cage comes in three different flow characteristics: quick-opening linear equal percentage 1. Valve body size: end connection size by nominal trim size. For example, a 4 x 2 inch Design EWD valve has 4-inch end connections with nominal 2-inch trim.
W2777-3 / IL
Figure 1. 12 x 6-Inch Design EWS Valve with Type 667 Actuator
Cavitrol III cages are available to eliminate cavitation damage and Whisper Trim III cages are available to help attenuate aerodynamic noise. Optional constructions allow full compliance with National Association of Corrosion Engineers (NACE) recommendations. See page 4. 316 stainless steel packing box parts are standard (including packing flange, studs, and nuts) D100023X012
Trim temperature capability with metal seats standard to 800 F (427 C)
Bulletin 51.1:EW Specifications Construction Materials
Valve Body Configurations
Valve, Bonnet, and Bonnet Spacer If Used: WCB carbon steel, LCC carbon steel, WC9 chrome moly steel, CF8M (316 SST), other materials upon request Valve Plug, Cage, and Metal Seating Parts Valve Bodies With All Except Cavitrol III or Whisper Trim III Cages: See table 5 or 14 Valve Bodies With Cavitrol III Cages: See table 15 Valve Bodies With Whisper Trim III Cages: See table 17 to 19 All Other Parts: See table 20
See Available Configurations section Valve Body Sizes See table 2 End Connection Styles Flanged: ANSI Class 300, 600, and 900 raisedface or ring-type joint flanges per ASME B16.5-1996 Buttwelding: Styles per ASME B16.25-1997 schedules that are consistent with ASME B16.34-1996 are Schedule 40 or 80 for all Class 300 and 600 valves, Schedule 80 or XXS for 8 x 6-in. Class 900 valves, or Schedule 80, 100, or 120 for 12 x 8-in. Class 900 valves
Material Temperature Capabilities(1) Valve Body/Trim Combinations Valve Bodies With All Except Cavitrol III or Whisper Trim III Cages: See figure 9 or 10 and table 11, 12, or 13 Valve Bodies With Cavitrol III Cages: See figure 12 and table 16 Valve Bodies With Whisper Trim III Cages: See figure 15, 16, or 17 and table 18 All Other Parts: See table 20
Maximum Inlet Pressures and Temperatures(1) Consistent with applicable Class 300, 600(2), or 900 pressure/temperature ratings per ASME B16.34-1996 unless limited as follows: Valves With All Except Cavitrol III or Whisper Trim III Cages: Where limited by individual pressure/temperature capabilities in figure 9 or 10 or temperature capabilities in table 11, 12, 13, or 20 Valves With Cavitrol III Cages: Where limited by individual pressure/temperature capabilities in figure 12 or temperature capabilities in table 16 or 20 Valves With Whisper Trim III Cages: Where limited by individual pressure/temperature capabilities in figure 15, 16, or 17 or temperature capabilities in table 18 or 20
Flow Characteristics Standard Cages: Quick-opening, linear, or equal percentage Cavitrol and Whisper Trim Cages: Linear Flow Directions Valves with Standard Cages Designs EWD, EWD-1, EWT, and EWT-1: Normally down(5) Designs EWS and EWS-1: Normally up(6) Valves with Cavitrol Cages: Always down(5) Valves with Whisper Trim III Cages: Always up(6)
Maximum Pressure Drops(1),(3) Same as maximum inlet pressure for specific construction defined above, except where further limited as follows: Valves With All Except Cavitrol III or Whisper Trim III Cages: See figure 9 or 10 Valves With Cavitrol III Cages: See figure 12 Valves With Whisper Trim III Cages: See figure 15, 16, or 17, except where further restricted by the following max P/P1 ratio — 0.60 for level A cages, 0.75 for level B cages, 0.85 for level C cages, or 0.99 for level D cages(4)
Flow Coefficients and Noise Level Prediction Refer to Fisher Controls Catalog 10 or Catalog 12 Port Diameters and Maximum Valve Plug Travels See table 21 Yoke Boss and Stem Diameters See table 21 Typical Bonnet Styles (see table 23)
Shutoff Classifications Per ANSI/FCI 70-2-1991
Plain, style 1 cast extension, style 2 cast extension, ENVIRO-SEAL bellows seal bonnet
See tables 3 and 4 – Continued –
2
Bulletin 51.1:EW Specifications (Continued) Packing Arrangements J Standard PTFE, J Double PTFE, J Graphite, J ENVIRO-SEAL PTFE, J ENVIRO-SEAL Duplex, J ENVIRO-SEAL Graphite, J HIGH-SEALt Approximate Weights See table 22 Options J Lubricator, J lubricator/isolating valve, J drilled and tapped connection in extension bonnet for leak-
off service, J valve body drain plug, J ENVIRO-SEAL bellows seal bonnet for positive stem sealing of hard-to-handle fluids at temperatures up to 1000_F (566_C), J style 3 fabricated extension bonnet made on order to a specific length for cryogenic service, J special seismic service bonnet, J packings suitable for nuclear service, and J forged bonnet for 5 in. (127 mm) yoke boss on 8 x 6 in. Class 900 valve, J Class V shutoff for EWT above 450_F (232_C) using PEEK anti-extrusion rings J Class V shutoff for EWD up to 1100_F (593_C) using C-seal trim
1. The pressure/temperature limits in this bulletin and any applicable standard or code limitation should not be exceeded. 2. For temperatures above 450_F (232_C), a buttwelding-end CF8M (316 stainless steel) valve body with a Class 600 pressure/temperature rating must be derated; contact your Fisher Con trols sales office or sales representative for details. Since ANSI standards do not allow use of intermediate ratings for flanged valve bodies, a Class 600 flanged-end CF8M valve body with B7 bolting must be limited either to 450_F (232_C) or to inlet pressures consistent with Class 300 ratings. 3. Only 12 x 8-in. Class 900 valve bodies with threaded (-1) seat rings can take full Class 900 pressure drops; Class 900 valve bodies with clamped (no dash number) seat rings arelimited to Class 600 pressure drops. Also, there are two different 8 x 6-in. Class 900 valve bodies, one for use only with Cavitrol III cages and the other for use with all other constructions. An 8 x 6-in. Class 900 valve body with Cavitrol III cage can take full Class 900 pressure drops. For information on other 8 x 6-in. constructions that can take full Class 900 pressure drops, contact your Fisher Controls sales office or sales representative. All other 8 x 6-in. constructions are limited to Class 600 pressure drops (1440 psid flowing drop) even though installed in a Class 900 valve body. 4. Restriction based on excessive noise if max P/P1 ratio for a given cage level is exceeded. 5. Down—in through cage and out through seat ring (direction shown in figure 2). 6. Up—in through seat ring and out through cage as shown in figure 13.
ENVIRO-SEALR Packing System Specifications Applicable Stem Diameters J 3/4 (19.1), J 1 (25.4), and J 1-1/4 (31.8) diameter valve stems Maximum Pressure/Temperature Limits(1) To Meet the EPA Fugitive Emission Standard of 500 PPM(2) For ENVIRO-SEAL PTFE and ENVIRO-SEAL Duplex packing systems: full ANSI Class 300 up to 450_ F (232_ C) For ENVIRO-SEAL Graphite packing system: 1500 psig (104 bar) at 600_ F (316_ C) Construction Materials
Male and Female Adaptor Rings: Carbon-filled PTFE V-ring Graphite Packing Systems: Graphite rings Anti-Extrusion Washer: Filled PTFE (not required for graphite packing) Lantern Ring: S31600 (316 stainless steel) (not required for graphite packing) Packing Box Flange: S31600 Spring: J 17-7PH stainless steel or J Inconel Packing Follower: S31600 lined with carbon-filled PTFE Packing Box Studs: Strain-hardened 316 stainless steel Packing Box Nuts: 316 stainless steel SA194 Grade 8M
PTFE Packing Systems: Packing Ring and Lower Wiper: PTFE V-ring(3) 1. Refer to the valve specifications in this bulletin for pressure/temperature limits of valve parts. Do not exceed the pressure/temperature rating of the valve. Do not exceed any applicable code or standard limitation. 2. The Environmental Protection Agency (EPA) has set a limit of 500 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services. 3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.
The temperature limits of Design EWT valves can be extended above 450_F (232_C) by using PEEK (PolyEtherEtherKetone) anti-extrusion rings in combination with a spring-loaded PTFE seal. The PEEK anti-extrusion rings expand to close off the clearance gap between the plug and the cage where the PTFE seal may extrude at high temperatures and pressures. The temperature limits are extended to 600_F (316_C) for non–oxidizing service and to 500_F (260_C) for oxidizing service. NOTE: EWN Series valves with Whisper Trim III cages are covered in a separate bulletin.
Features D Compliance with the Clean Air Act—Patented ENVIRO-SEAL packing systems provide a superior stem seal to help prevent the loss of valuable or hazardous process fluid. The ENVIRO-SEAL packing systems feature PTFE or graphite packing with live-loading for reduced packing maintenance. D Noise Attenuation—In an EW Series valve, noise produced by high flow rates and large pressure drops can be reduced by up to 18 dbA with a Whisper Trim I cage and by up to 30 dbA with a Whisper Trim III cage.
3
Bulletin 51.1:EW Piping Economy—Expanded end connections of EW Series valve bodies may reduce the need for line swages while accommodating oversized piping arrangements used to limit fluid flow velocities. Temperature Compensation—On designs with the seat ring threaded into the valve body (figure 5), the hung cage feature helps reduce gasketing problems caused by thermal expansion and contraction of long parts, such as the cage assembly. Standard Trim Parts across the easy-e product line—Included are FGM gaskets, packing flange, studs, and nuts. High-Temperature, Class IV or Class V Shutoff—Optional multiple piston rings (figure 14) for Design EWD and EWD-1 valve bodies permit Class IV shutoff up to 1100 F (593 C). Use of C-seal trim (see figure 6) permits Class V shutoff up to 1100 F (593 C). Increased Pressure/Temperature Ratings—12 x 8 inch Class 900 EW Series valve bodies with buttwelding end connections are capable of increased ANSI ratings called Intermediate Standard Ratings. The extra strength of the valve body allows these valves to be used where pressures and temperatures exceed Standard Class ratings in ASME B16.34. See Bulletin 59.1:027, Increased Pressure/Temperature Ratings for EW Series Steel Valve Bodies, for further information. Sour Gas Service Capability—Optional special trim and bolting materials are available for applications handling sour fluids and gases. These constructions comply with the recommendations of the National Association of Corrosion Engineers (NACE) MR0175. Because of the care exercised by Fisher Controls in procurement and manufacturing, additional testing and documentation to assure compliance with the NACE standard is not required, in most cases.
C-seal Trim Description C-seal trim (figure 6) is available for valves with port diameters from 2-7/8 inches through 8 inches. With C-seal trim, a balanced valve can achieve hightemperature, Class V shutoff. Because the C-seal plug seal is formed from metal (N07718 nickel alloy, Inconel 718) rather than an elastomer, a valve equipped with the C-seal trim can be applied in processes with a fluid temperature of up to 1100 F (593 C).
These systems help you seal your process to conserve valuable process fluid and to protect the environment against the emission of toxic or polluting fluids. The long-life and reliability of these systems also reduce your maintenance cost and downtime. For applications requiring compliance with environmental protection regulations, Fisher Controls offers the unique ENVIRO-SEAL packing system and, for toxic or lethal service, the ENVIRO-SEAL bellows seal bonnet (figure 19). The patented emission control packing system or seal bonnet keeps emission concentrations below the EPA 500 ppm requirement. For a superior stem seal in applications that are not environmentally-sensitive, Fisher Controls offers the HIGH-SEAL graphite packing system. The HIGH-SEAL packing system provides superior sealing at pressure/temperature ratings beyond ENVIRO-SEAL limits. ENVIRO-SEAL packing systems, available with PTFE, graphite, or Duplex packing, and the HIGH-SEAL graphite packing system feature live-loading and unique packing-ring arrangements for long-term, consistent sealing performance.
NACE Standard MR0175 Compliance Standard procurement procedures and manufacturing processes used by Fisher Controls assure that control valves with sour service trims comply with the chemical and physical requirements of NACE standard MR0175. Incoming raw materials are selected for sour service trims by specifications covering chemical composition, forming, hardness, heat treatment, and finish. In addition, the subsequent machining, welding, and heat treatment of the materials being processed into finished parts is strictly regulated by manufacturing standards. Because of strict start-to-finish manufacturing quality management, Fisher Controls offers a high degree of confidence that the parts and assemblies provided for sour service comply with MR0175. Additional testing and documentation to assure compliance with MR0175 is not necessary, in most cases. However, in cases where documentation is required, the following items can be provided: hardness test data
ENVIRO-SEAL and HIGH-SEAL Packing Systems
certificate of compliance to specification
The ENVIRO-SEAL and HIGH-SEAL packing systems (figure 18) from Fisher Controls offer exceptional sealing capabilities. These systems easily install in your existing valves or can be purchased with new valves.
chemical and physical test data
4
heat treatment documentation
The requirements of the NACE standard are very specific and the application of the standard to control
Bulletin 51.1:EW
PTFE V–RING PACKING BONNET GASKET SHIM SPIRAL WOUND GASKET
PIN
GRAPHITE PISTON RING VALVE PLUG
LOAD RING CAGE RETAINER
CAGE SEAT RING
SEAT RING GASKET W2280–2*/IL
W3318-1 / IL
NOTE: THE 10 x 8 INCH VALVE IS SIMILAR IN APPEARANCE TO SIZES THROUGH 12 x 6 INCHES. HOWEVER, THE 10 x 8 INCH SIZE USES THE LOAD RING SHOWN FOR THE 12 x 8 INCH SIZE. IT DOES NOT USE THE CAGE RETAINER.
Figure 2. Class 300 or 600 Design EWD Valve with Standard Cage
Martensitic and cast precipitation hardening stainless steel are not used. Control valve packing sets are jam style only. Valve stems are made from S20910 (Nitronic 50). Plating and coatings are used only over suitable base metals and are not intended for corrosion protection.
W0989–2/IL
CLAMPED METAL SEAT RING
Figure 3. Design EWS trim Details Showing Standard Cage and Seating Construction
valve materials is quite complex. There are, however, some general guidelines that are always followed: All carbon steel valve bodies and bonnets are heat-treated to 22 HRC maximum and are post-weld heat-treated.
No machining operations that cause work hardening of the materials are performed in the manufacturing process. Primary trim materials are S31600 and alloy 6. Flat sheet gaskets are standard graphite/S31600 (316 SST), spiral wound gaskets are standard Inconel 600/graphite. Bolting in NACE MR0175 (non-exposed bolting) material is provided as standard. Bolting in NACE MR0175 (exposed bolting) material is available as an option.
5
Bulletin 51.1:EW SOFT BACKUP RING
SEAL RING
SEAL RING (SHOWN POSITIONED FOR USE WITH STANDARD AND CAVITROL CAGES)
RETAINING RING
METAL BACKUP RING
W2914–1 / IL
W0995–2 / IL
PTFE DISC
METAL DISC SEAT
METAL DISC RETAINER
5-3/8 INCH (137 mm) AND SMALLER PORTS
SEAL RING (SHOWN POSITIONED FOR USE WITH STANDARD AND CAVITROL CAGES)
7 INCH (178 mm) AND LARGER PORTS
W0992–3 / IL
STANDARD CONSTRUCTION (SEAT PARTS ALSO TYPICAL OF OPTIONAL DESIGN EWS PTFE SEATING )
VALVE PLUG WITH OPTIONAL PRESSURE-ASSISTED SEAL RING
Figure 4. Design EWT Trim Details
SEAL RING (SHOWN POSITIONED FOR USE WITH STANDARD CAGES)
THREADED SEAT RING W3320–2 / IL
Figure 5. 12 x 8-Inch Class 900 Design EWT-1 Valve
6
Bulletin 51.1:EW STAKE THREAD
PISTON RING
RETAINER
C-SEAL METAL PLUG SEAL(1)
VALVE PLUG
NOTES: 1. REVERSE THE ORIENTATION OF THE C-SEAL PLUG SEAL FOR PROPER SHUTOFF WHEN VALVE IS USED IN A PROCESS WITH DIFFERENT FLUID FLOW DIRECTION. A6869 / IL
C-SEAL METAL PLUG SEAL(1)
Figure 6. C-seal Trim
VALVE PLUG SEAL
A7096 / IL
PROTECTED SOFT SEAT
Figure 7. Typical Balanced TSO Trim
7
Bulletin 51.1:EW Table 1. Metal Trim Part Materials for Compliance with NACE MR0175 (Sour Service) Specifications Optional Disk Seat and Valve Stem, Seat Ring Retainer for Packing Follower, Liner Trim for Standard Valve Plug Cage Optional for Metal Lantern Ring, Metal Seat Designation PTFE-Seat Seat Packing Box Ring, Construction (EAT only) Construction and Pin 85
85C(2)
86
S31600
S31600 with electroless nickel coating (ENC)
S31600
S31600
–––
S31600
S31600 with electroless nickel coating (ENC)
–––
–––
S31600
S31600 with seat hard faced with CoCr-A hardfacing alloy
S31600 with electroless nickel coating (ENC)
R30006 (alloy 6)
–––
–––
S31600 with electroless nickel coating (ENC)
R30006 (alloy 6)
–––
–––
S31600 with electroless nickel coating (ENC)
–––
–––
S31600
S31600 with seat and guide hard faced with CoCr-A hardfacing alloy S31600 with seat and guide hard faced with CoCr-A hardfacing alloy
87
87C(2)
Load Ring(1)
S20910 (Valve Stem) S31600 (All Other Parts)
N05500 (K-Monel) ( )
1. 10x8 and 12x8-inch valve body only. 2. 85C and 87C are trims for PTFE-seat construction.
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °C 0
50
100
150
–100 –50
200 250 100
1400
0
50 100
150
200 250 300 110
1600
110
1600
100
1400
90
90
70
1000
60 800 50
87C
600
40 30
400
20 200
0 500
2 NOTES: 1 USE TRIM 87 INSTEAD OF TRIM 85 FOR NONLUBRICATING FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASES BETWEEN 300°F (149°C) AND 600°F (316°C). 2 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES. A3115–3 / IL
Figure 8. Typical Trim for NACE MR0175 Specification (Sour Service)
8
70
800
60
87
86
50 600
40
400
30 20 85
10
0 –100 0 100 200 300 400 –50 FLUID TEMPERATURE, °F
80
1000
200
85C
–200
PRESSURE DROP, PSI
80
1200 PRESSURE DROP, BAR
PRESSURE DROP, PSI
1200
1
3
10
0 –200
PRESSURE DROP, BAR
–100 –50
0 –100
0
100
200
300
400 500 450 4
600
FLUID TEMPERATURE, °F
2
3 USE TRIM 85 UP TO 1440 PSI (99 BAR) WITH CLEAN DRY GAS. FOR PROCESS FLUIDS OTHER THAN CLEAN DRY GAS, USE TRIM 85 ONLY UP TO 300 PSI (21 BAR). 4 TRIM 87 TEMPERATURE LIMIT CAN BE EXTENDED ABOVE 450°F (232°C)F IF PEEK ANTI-EXTRUSION RINGS AND SPRING– LOADED SEAL RING ARE USED.
Bulletin 51.1:EW Table 2. Available Valve Constructions(1) VALVE SIZE(2), INCHES VALVE DESIGN EWD EWD-1 EWS EWS-1 EWT EWT-1
Class 300 or 600 4x2
6x4
8x4
8x6
8 x 6 with 10-inch ends
x --x --x ---
x --x --x ---
x --x --x ---
x --x --x ---
x --x --x ---
Class 900 12 x 6
10 x 8
12 x 8
8x6
12 x 8
x --x --x ---
x --x --x ---
x --x --x ---
x --x --x ---
x x x x x x
1. X indicates available construction. 2. Two-number valve size designates end connection size x trim size.
Available Configurations All configurations covered in this bulletin use a singleport, globe-style valve body with cage guiding and push-down-to-close valve plug action. This valve style is combined with different plug styles and either a clamped seat ring (no dash number suffix) or a seat ring threaded into the valve body (-1 suffix). Design EWD: Balanced valve plug (figure 2) with clamped seat ring and metal-to-metal seating for all general applications over a wide range of pressure drops and temperatures. Design EWD-1: 12 x 8 inch Class 900 Design EWD valve body, with threaded seat ring. Design EWS: Unbalanced valve plug (figure 3) with clamped seat ring and metal-to-metal or optional metal-to-PTFE seating for all general applications requiring better shutoff capabilities than can be obtained with the Design EWD valve body. Design EWS-1: 12 x 8 inch Class 900 Design EWS valve body, with threaded seat ring and metal-to-metal seating. Design EWT: Balanced valve plug (figure 4) with metal-to-PTFE seating (for stringent shutoff requirements) standard in all Design EWT valves (except those with Cavitrol III cages). Metal-to-metal seating for higher temperatures is standard for all Design EWT valve bodies with Cavitrol III cages and optional for these valves with other cages. Design EWT-1: 12 x 8 inch Class 900 Design EWT valve body, with threaded seat ring and with metal-tometal seating (figure 5).
Material Selection Guidelines Regardless of valve construction, select the valve body/bonnet material from the specifications table,
keeping in mind that the valve service conditions cannot exceed the ASME/ANSI pressure/temperature limitations for the selected valve body. Then, perform steps 1 and 2 under the appropriate valve design heading to complete the selection process. Design EWD, EWS, or EWT Valve With All Except Cavitrol III or Whisper Trim III Cages 1. Choose a trim combination for the service conditions according to figure 9, while making sure from table 5 that this combination provides the desired trim materials. Then, make sure from table 11, 12, or 13 that the valve body/trim temperature limits are not exceeded. 2. Finally, check in table 20 that packing and other valve parts are available in materials that meet the desired service conditions. Design EWD-1, EWS-1, or EWT-1 Valve With Standard Cage 1. Choose a trim combination for the service conditions according to figure 10, while making sure from table 7 that this combination provides the desired trim materials. 2. Finally, check in table 20 that packing and other valve parts are available in materials that meet the desired service conditions. Design EWT Valve With Cavitrol III Cage 1. Choose a trim combination for the service conditions according to figure 12, while making sure from table 15 that this combination provides the desired trim materials. Then, make sure from table 16 that the valve body/trim temperature limits are not exceeded. 2. Finally, check in table 20 that packing and other valve parts are available in materials that meet the desired service conditions.
9
Bulletin 51.1:EW Table 3. Shutoff Classifications per ANSI/FCI 70-2-1991 Valve Design
Seating
EWD or EWD-1
Metal
Shutoff Class II (standard) III (optional for 6 x 4 through 12 x 6 inch valves with optional graphite piston ring; optional for 10 x 8 and 12 x 8 inch valves with optional double piston rings) IV (optional for 6 x 4 through 12 x 8 inch valves with optional multiple graphite piston rings)
EWS or EWS-1
Metal
IV (standard)
EWS
PTFE
VI
EWT with all except C it l III cages Cavitrol
PTFE
Standard air test (maximum leakage is 0.05 mL/min/psid/inch port diameter)
V (optional, consult your Fisher Controls sales representative or sales office)
V (optional) Metal
IV V(1)
EWT with 1 t 1-stage C it l III cage Cavitrol
Metal
IV (standard)
EWT with 2-stage Cavitrol III cage or 2- or 3-stage Cavitrol III cage
Metal or PTFE
V
EWT-1
Metal
IV
V (optional)
1. Class V shutoff for Design EWT requires spring-loaded seal ring, radius-seat plug, and wide-bevel seat ring. Not available with 8-inch port, quick-opening cage. Not available with S31600 (316 SST) valve plug and seat ring (trims 4, 29, 85, 310).
Table 4. C-seal Shutoff Classification Valve Design (Class)
Design EWD (Class 300, 600)
Valve Size, Inches
Port Diameter, Inches (mm)
Cage Style
6 x 4 x 2-1/2
2-7/8 (73)
Eq. %, Linear, Whisper I, Cav III (2-stage)
6x4 8x4
4-3/8 (111.1)
Eq. %, Linear, Whisper I, Cav III (1-stage)
8x6 12 x 6
5-3/8 (136.5)
Whisper III (A3, B3, D3, D3), Cav III (2-stage)
8x6 12 x 6
7 (177.8)
Eq. %, Linear, Whisper I, Cav III (1-stage)
10 x 8 12 x 8
8 (203.2)
Eq. %, Linear, Whisper I, Cav III (1-stage)
Design EWD, EWS, or EWT Valve With Whisper Trim III Cage 1. Choose a trim combination for the service conditions according to figure 15, while making sure from table 17 that this combination provides the desired trim materials. Then, make sure from table 18 that the valve body/trim temperature limits are not exceeded. 2. Finally, check in table 20 that packing and other valve parts are available in materials that meet the desired service conditions. Design EWD-1, or EWT-1 Valve With Whisper Trim III Cage 1. Choose a trim combination for the service conditions according to figure 16 or 17, while making sure from table 19 that this combination provides the desired trim materials.
10
ANSI Leakage Class
V to 1100 1100 F F (593 (593 C) C) (for port diameters from 2 2-7/8 7/8 through 8-inch with optional C-seal trim)
2. Finally, check in table 20 that packing and other valve parts are available in materials that meet the desired service conditions.
Installation Unless limited by seismic criteria, the valve body can be installed in any position (as long as sufficient support is provided if a fabricated extension bonnet is used). However, the normal method is with the actuator vertical above the valve, since nonvertical positions may cause uneven trim wear and decreased trim life. Flow through the valve body must be in the direction indicated by the flow direction arrow on the valve body. Consider installing an upstream strainer, especially if the valve body includes slotted or multihole Whisper Trim or Cavitrol cages. Dimensions are shown in figure 20.
Bulletin 51.1:EW Table 5. Design EWD, EWS, and EWT Metal Trim Part Combinations(1) Except for Valves with Cavitrol III or Whisper Trim III Cages SEAT TRIM DESIGNATIONS
VALVE PLUG
CAGE
Disk Seat, Retainer for PTFE Seat Constructions ---
Seat Ring for Metal Seat Constructions S41600 for Types EWD, EWS S41000 for 8 x 6-inch, Class 900 Types EWD, EWS CA6NM for Types EWD-1, EWS-1, EWT-1
1 (standard trim for all valves except Design EWT and those in CF8M. Trim 57 is standard for Design EWT. Trim 29 is standard for all valves in CF8M)
S41600 hardened to 38 HRC (minimum)
CB7CU-1 (S17400) hardened to 40 HRC (minimum)
3 and 3H(2)
S31600 w/seat and guide hard faced w/CoCr-A hardfacing alloy
R30006 (alloy 6)(3)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
4
S31600
S31600
S31600
27
S31600 w/seat and guide hard faced w/CoCr-A hardfacing alloy
CB7CU-1 (S17400) hardened to 40 HRC (minimum) CF8M w/electroless nickel coating (ENC)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
29 (standard for all valves in CF8M)
S31600
CF8M w/electroless nickel coating (ENC)
S31600
S31600
37 and 37H(2)
S31600 w/seat and guide hard faced w/CoCr-A hardfacing alloy
CB7CU-1 (S17400) hardened to 40 HRC (minimum)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
S31600 w/seat hard faced w/CoCr-A hardfacing alloy(4)
57 (standard for all Design EWT valve bodies in all materials except CF8M)
S41600 hardened to 38 HRC (minimum)
CB7CU-1 (S17400) hardened to 40 HRC (minimum)
S31600
1. 2. 3. 4.
---
Nonferrous alloy combinations are also available. Consult your Fisher Controls sales office or sales representative for details. Trims 3H and 37H have clearances for high-temperature service. Available only in linear, quick-opening, equal percentage, and Whisper Trim I cages. Solid cast alloy 6 seat ring is used instead for 4 x 2, 10 x 8, and 12 x 8 inch valve sizes.
ANSI/FCI Class VI Shut-off Capabilities Design EWS valves with metal seat constructions and Design EWT valves with soft seat and metal seat constructions can provide ANSI/FCI Class VI shut-off capabilities. See tables 6 and 7. Table 6. Class VI Shut-off Availability Type
Port Size, Inches
Seat
Minimum Seat Load
EWS
7
Metal
300 lbs/lineal inch
EWT
3-7/16 7
Soft
See Catalog 14
EWT
3-7/16 7
Metal
300 lbs/lineal inch
Table 7. Class VI Trim Materials TYPE
EWS
CAGE/SEAT RING RETAINER
VALVE PLUG
SEAT RING
SEAL RING
S31600 (316 SST) / ENC
S31600/CoCr-A (alloy 6) seat w/ radiused seat (special design)
S31600 w/ wide beveled seat (special design)
S31600 / ENC
S31600 w/ standard beveled seat
S31600 / ENC EWT
S17400 (17-4PH SST) S17400
S31600/CoCr-A seat w/ radiused seat (special design) S41600 w/ standard beveled seat S41600 w/ radiused seat (special design)
TRIM TEMPERATURE LIMIT F
C
NA
Not a limiting factor
Not a limiting factor
S31600/PTFE
UHMWPE(1) Elgiloy
–20 to 150
–29 to 66
S31600 w/ wide beveled seat (special design)
UHMWPE Elgiloy
–150 to 150
–101 to 66
S31600/PTFE
UHMWPE Elgiloy
–20 to 150
–29 to 66
S31600 w/ wide beveled seat (special design)
UHMWPE Elgiloy
–20 to 150
–29 to 66
1. UHMWPE (Ultra High Molecular Weight Polyethylene)
11
Bulletin 51.1:EW Fisher TSO (Tight Shutoff) Trim Capabilities See figure 7 and tables 8, 9, and 10. For additional information contact your Fisher Controls sales representative or sales office. Table 8. TSO (Tight Shutoff) Leakage Class Leakage Class TSO (Tight Shutoff)
Maximum Leakage Valves with TSO trim are factory tested to a more stringent Fisher Controls test requirement of no leakage at time of shipment.
Test Medium
Test Pressure
Water
Service ∆P(1)
Test Procedure ANSI/FCI Class V test procedure B
1. Specify service ∆P when ordering.
Table 9. TSO Shutoff Availability TYPE EWT
LEAK CLASS
CONSTRUCTION Std or Cavitrol III trim. Replaceable, protected soft seat
Standard
Optional
TSO
---
Table 10. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim VALVE TYPE
TRIM
EWT 6x4-Inch
Std
EWT 8x6-Inch 8x6 Inch
Std
MAX TRAVEL
YOKE BOSS SIZE
Actual TSO
Inch
mm
Inch
mm
Inch
mm
Inch
mm
2
50.8
3-9/16
90
4-3/8
111
4-3/16
106
2
50.8
3-9/16 5
90 127
7
179
6-13/16 6 13/16
173
4
102
3-9/16
90
1. This column lists the percent reduction of published maximum CV of the trim listed in the TRIM column.
12
PORT DIAMETER Nominal
CV REDUCTION AT 100% TRAVEL(1) 4% (linear) 3% (equal percent) 2% 2%
Bulletin 51.1:EW
PRESSURE DROP, PSI
PRESSURE DROP, PSI
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
-20 FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °F
FOR PTFE SEATING WITH ALL CLASS 600 OR 900 BODY MATERIALS 2
WITH CLASS 600 OR 900 WCB OR LCC STEEL BODY
PRESSURE DROP, PSI
PRESSURE DROP, BAR
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
PRESSURE DROP, PSI
FLUID TEMPERATURE, °C
2
1050 FLUID TEMPERATURE, °F
WITH CLASS 600 OR 900 WC9 CHROME MOLY STEEL BODY
FLUID TEMPERATURE, °F
2
NOTES: 1 BE ESPECIALLY CAREFUL TO SPECIFY SERVICE TEMPERATURE IF TRIM 3,4, OR 37 IS SELECTED, AS DIFFERENT THERMAL EXPANSION RATES REQUIRE SPECIAL PLUG CLEARANCES, ALSO, USE TRIM 37H INSTEAD OF TRIM 4 FOR NON–LUBRICATING FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASES BETWEEN 300°F (149°C) AND 600°F (316°C). 2 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
WITH CLASS 600 OR 900 CF8M (316SST) BODY
2
3 USE TRIM 27 INSTEAD OF TRIM 29 FOR NON–LUBRICATING FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASES BETWEEN 300°F (149°C) AND 600°F (316°C). 4 TRIMS 4 AND 29 MAY BE USED OVER 300 PSI ONLY WITH CLEAN, DRY GAS.
A6334–1 / IL
Figure 9. Typical Trim Used in Design EWD, EWS, or EWT Valves Except Those with Cavitrol III or Whisper Trim III Cages
13
Bulletin 51.1:EW Table 11. Valve/Trim Temperature Capabilities(1) for Class 300 or 600 Design EWD, EWS, and EWT Valves with 2-Inch (51 mm) or 3-Inch (76 mm) Travel (Except those with Cavitrol III or Whisper Trim III Cages) MATERIAL TEMPERATURE CAPABILITY VALVE/BONNET MATERIAL
TRIM DESIGNATION FROM TABLE 5
C Max
Min
Max
37
4x2 6x4 8x4 8x6 12 x 6 12 x 8 & 10 x 8 4x2 6x4 8x4 8x6 12 x 6 12 x 8 & 10 x 8 4 x 2 through 12 x 8
–20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20
750 650 625 600 500 800 600 430 425 400 345 600 410
–29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29
399 343 329 316 260 427 316 221 218 204 174 316 210
37H
4 x 2 through 12 x 8
410
800
210
427
57
4 x 2 through 12 x 8
–20
400
–29
204
4x2 6x4 8x4 8x6 12 x 6 10 x 8 4 x 2 through 10 x 8
–20 –20 –20 –20 –20 –20 –20
700 650 625 625 500 650 400
–29 –29 –29 –29 –29 –29 –29
371 343 329 329 260 343 204
37
4x2 6x4 8x4 8x6 12 x 6 10 x 8 4 x 2 through 12 x 8
–50 –50 –50 –50 –50 –50 –20
600 425 425 400 325 600 410
–46 –46 –46 –46 –46 –46 –29
316 218 218 204 163 316 210
37H
4 x 2 through 12 x 8
410
700
210
371
3
4x2 6x4 8x4 8x6 12 x 6 12 x 8 & 10 x 8 4 x 2 through 12 x 8
–20 –20 –20 –20 –20 –20 –20
750 650 625 600 500 800 800
–29 –29 –29 –29 –29 –29 –29
399 343 329 316 260 427 427
3H
4 x 2 through 12 x 8
800
1050
427
566
37
4x2 6x4 8x4 8x6 12 x 6 12 x 8 & 10 x 8 4x2 6x4 8x4 8x6 12 x 6 12 x 8 & 10 x 8 4 x 2 thru 12 x 8
–20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20 –20
650 430 425 400 325 650 600 430 425 400 325 600 410
–29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29 –29
343 221 218 204 163 343 316 221 218 204 163 316 210
37H
4 x 2 thru 12 x 8
410
800
210
427
57
4 x 2 through 12 x 8
–20
400
–29
204
27
4 x 2 through 12 x 8
–325(6)
650
–198(6)
343
29
4 x 2 through 12 x 8
–325(6)
600
–198(6)
316
WCB steel 29
1
57 LCC steel 29
1
27
29
CF8M (316 SST)(5)
F Min
1
WC9 chrome moly steel
VALVE SIZE, SIZE INCHES
1. For metal trim parts only. 2. Except 550 F (288 C) for trim 29. 3. Except 600 F (316 C) for trim 26. 4. Except 450 F (232 C) for trim 29. 5. For temperatures above 450 F (232 C), buttwelding-end CF8M valves having a Class 600 pressure-temperature rating must be derated; contact your Fisher Controls sales office or sales representative for further information. Since ANSI standards do not allow use of intermediate pressure-temperature ratings for flanged valves, flanged-end CF8M valves having a Class 600 pressure-temperature rating must be limited to 450 F (232 C) or must be limited to inlet pressures that are consistent with the Class 300 pressure-temperature rating. 6. May be used down to –425 F (–254 C) if manufacturing process includes Charpy Impact test.
14
Bulletin 51.1:EW Table 12. 4-Inch (102 mm) Travel Whisper Trim I Design EWD and EWT Valve Body/Trim Temperature Capabilities(1) (Class 150 - 600 and Size 8 x 6, Class 900) BODY/BONNET MATERIAL(2)
TRIM DESIGNATION FROM TABLE 5
WCB steel
LCC steel
WC9 chrome moly steel
MATERIAL TEMPERATURE CAPABILITY VALVE SIZE, SIZE INCH
F
C
Min
Max
Min
Max
1
8x6 12 x 6
–20 –20
625 545
–29 –29
329 285
3
8 x 6 or 12 x 6
–20
800
–29
427
57
8 x 6 or 12 x 6
–20
400
–29
204
37
8 x 6 or 12 x 6
–20
410
–29
210
37H
8x6 12 x 6
410 410
800 685
210 210
427 363
1
8 x 6 only
–20
625
–29
329
4, 57
8 x 6 only
–20
400
–29
204
37
8 x 6 only
–20
410
–29
210
37H
8 x 6 only
410
650
210
343
3
8 x 6 or 12 x 6
–20
800
–29
427
3H
8 x 6 or 12 x 6
800
1050
427
566
1. For metal trim parts only. 2. Same material also used for bonnet spacer.
Table 13. Class 900 Design EWD, EWS, and EWT Valve Body/Trim Temperature Capabilities(1) BODY/BONNET MATERIAL
TRIM DESIGNATION FROM TABLE 5
WC9 chrome moly steel
316 SST (CF8M)
F
C
Min
Max
Min
Max
1
8x6 12 x 8
–20 –20
600 800
–29 –29
316 427
29
8x6 12 x 8
–20 –20
400 600
–29 –29
204 316
37
8 x 6 or 12 x 8
–20
410
–29
210
37H
8 x 6 or 12 x 8
410
800
210
427
57
8 x 6 or 12 x 8
–20
400
–29
204
1
8 x 6 only
–20
625
–29
329
4, 37
8 x 6 only
–50
410
–46
210
37H
8 x 6 only
410
700
210
371
57
8 x 6 only
–20
400
–29
204
29
8 x 6 only
–50
400
–46
204
1
8x6 12 x 8
–20 –20
600 800
–29 –29
316 427
3
8x6
–20
800
–29
427
3H
8x6
800
1050
427
566
3
12 x 8
–20
800
–29
427
3H
12 x 8
800
1050
427
566
27
8x6 12 x 8
–20 –20
400 650
–29 –29
204 343
29
8x6 12 x 8
–20 –20
400 600
–29 –29
204 316
37
8 x 6 or 12 x 8
–20
410
–29
210
37H
8 x 6 or 12 x 8
410
800
210
427
57
8 x 6 or 12 x 8
–20
400
–29
204
27
8 x 6 or 12 x 8
–325(2)
650
–198(2)
343
29
8 x 6 or 12 x 8
–325(2)
600
–198(2)
316
WCB steel
LCC steel
MATERIAL TEMPERATURE CAPABILITY
VALVE SIZE, INCH
1. For metal trim parts only. 2. May be used down to –425 F (–254 C) if manufacturing process includes Charpy impact test.
15
Bulletin 51.1:EW
PRESSURE DROP, BAR
PRESSURE DROP, PSI
FLUID TEMPERATURE, °F
WITH WCB STEEL BODY
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
PRESSURE DROP, PSI
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °F
WITH WC9 CHROME MOLY STEEL BODY
1
1
PRESSURE DROP, PSI
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
NOTE: 1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
FLUID TEMPERATURE, °F
WITH CF8M (316 SST) BODY A6334–1 / IL
Figure 10. Typical Trim Used in Design EWD-1, EWS-1, and EWT-1 Valves with Standard Cages
16
1
Bulletin 51.1:EW Table 14. Class 900, 12 x 8 Inch, Design EWD-1, EWS-1, and EWT-1 Metal Trim Part Combinations Except for Valves with Whisper Trim III Cages Trim Designation
Valve Plug
Cage
Seat Ring
1
S41600 (416 SST) hardened to 38 Rockwell C (min)
CB7CU-1 (17-4PH SST) with H900 heat-treat condition
Heat-treated CA6NM(1)
27
316 SST with seat and guide hard-faced with CoCr-A
316 SST with electroless nickel coating (ENC)
316 SST with seat hard-faced with CoCr-A
37 & 37H(2)
S31600 with seat and guide hard-faced with CoCr-A
CB7CU-1 with H900 heat-treat condition
S31600 with seat hard-faced with CoCr-A
1. CA6NM is similar to 410 SST. 2. Trim 37H has clearances for high-temperature service.
PRESSURE DROP, PSI
CAGE RETAINER/ BONNET SPACER
PRESSURE DROP, BAR
LIQUID TEMPERATURE, °C
W3331–1 / IL
LIQUID TEMPERATURE, °F NOTE: DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES. A2732 / IL
Figure 11. Detail of 2-Stage Cavitrol III Cage in Class 300 or 600 Design EWT Valve
Figure 12. Typical Trim Used in Cavitrol III Cage Constructions with Steel or Stainless Steel Valves
17
Bulletin 51.1:EW OPTIONAL TRIPLE PISTON RINGS USED TO OBTAIN CLASS IV SHUTOFF (THIS OPTIONAL SHUTOFF ALSO AVAILABLE IN OTHER DESIGN EWD SIZES AND CONSTRUC– TIONS)
BACKUP RING
CAGE RETAINER BONNET SPACER
SEAL RING BAFFLE CAGE
W0997–2 / IL W3361–1 / IL
Figure 13. Design EWT Metal-Seat Valve with Whisper Trim I Cage
Figure 14. 8 x 6-Inch Design EWD Valve with Whisper Trim III Cage
PRESSURE DROP, PSI
PRESSURE DROP, BAR
PRESSURE DROP, PSI
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °C
1050 FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °F
WITH CLASS 600 WCB STEEL OR WC9 CHROME MOLY VALVE 1
WITH CLASS 600 CF8M (316SST) VALVE
NOTE: 1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES. A6334 / IL
Figure 15. Typical Trim Used in Design EWD, EWS, and EWT Valves with Whisper Trim III Cages
18
1
Bulletin 51.1:EW Table 15. Cavitrol III(1) Metal Trim Part Combination Trim Designation
Valve Plug
Cage
Cage Retainer(2)
Seat Ring
76
Heat-treated S42000 (420 SST)
S17400 (17-4PH SST) with H900 heat-treat condition
S31600 (316 SST)
S17400 with H900 heat-treat condition
1. Available only in Design EWT valve. 2. Not used in 12 x 8 or 8 x 6 inch Class 900 valves.
Table 16. Cavitrol III Valve Body/Trim Temperature Capabilities TRIM DESIGNATION FROM TABLE 15
MATERIAL TEMPERATURE CAPABILITY
VALVE BODY & BONNET
Minimum WCB carbon steel or WC9 chrome moly steel
–20 F (–29 C)
LCC carbon steel 76 S31600 (316 SST)
Maximum
–50 F (–46 C)
These materials not limiting factors
4 x 2 inch valve size 6 x 4 inch valve size 8 x 4 inch valve size
–20 F (–29 C) –20 F (–29 C) –20 F (–29 C)
400 F (204 C) 300 F (149 C) 275 F (135 C)
8 x 6 inch valve size(1) 12 x 6 inch valve size 12 x 8 inch valve size(2)
–20 F (–29 C) –20 F (–29 C) –20 F (–29 C)
250 F (121 C) 225 F (107 C) 350 F (177 C)
1. This valve body/trim combination not available in Class 900 valve. 2. This valve body/trim combination available in all 12 x 8 inch rating classes.
(1) Table 17. Metal Trim Part Combinations for Design EWD, EWS, and EWT Valves with Whisper Trim III Cages
Trim Designation 301 (standard for all valve materials except CF8M [316 SST]) 301C
304 310 (standard for CF8M valves) 313 (NACE compatible)(2) 313C (NACE compatible)(2) 315
317
318
Valve Plug
Cage
S17400 (17-4PH SST) hardened to 40 HRC (min) S17400 (17-4PH SST) hardened to 40 HRC (min) S31600 with seat and guide hard-faced with CoCr-A (Alloy 6)
S41600 (416 SST) hardened to 38 HRC (min) S41600 (416 SST) hardened to 38 HRC (min) S41600 hardened to 38 HRC (min) S31600 with electroless nickel coating (ENC) S31600 with electroless nickel coating (ENC) S31600 with electroless nickel coating (ENC)
S31600 S31600 with seat and guide hard-faced with CoCr-A S31600 with seat and guide hard-faced with CoCr-A S31600 with seat and guide hard-faced with CoCr-A S31600 with seat and guide hard-faced with CoCr-A S31600 with seat and guide hard-faced with CoCr-A
Cage Retainer WCB/A105 heattreated 22 HRC (NACE with ENC) WCB/A105 heattreated 22 HRC (NACE with ENC) WCB/A105 heattreated 22 HRC (NACE with ENC) S31600 with ENC WCB/A105 heattreated 22 HRC (NACE with ENC) WCB/A105 heattreated 22 HRC (NACE with ENC)
Baffle (for Level D3 Cage Only)
Disk Seat and Retainer for PTFE-Seat Construction
Seat Ring for Metal-Seat Construction
Steel
---
S41600 (416 SST) hardened to 38 HRC (min)
Steel
S31600 (316 SST)
Steel
---
S31600
Steel
Steel
S31600
---
S31600
--S31600 with seat hard-faced with CoCr-A S31600 S31600 with seat hard-faced with CoCr-A ---
Electrolized S31600
Electrolized S31600 S31600
---
S31600 with seat hard-faced with CoCr-A
WC9/Ion Nitrided
WCB/Ion Nitrided
Steel
---
S41600
WC9/Ion Nitrided
WC9/Ion Nitrided
WC9
---
S31600 with seat hard-faced with CoCr-A
1. For 8 x 6 or 12 x 6 -inch valves only. 2. Level D3 cage cannot be certified to NACE. Use 316/ENC cage retainer instead.
19
Bulletin 51.1:EW Table 18. Valve/Trim Temperature Capabilities for Design EWD, EWS, and EWT Valves with Whisper Trim III Cages VALVE/BONNET/ BONNET SPACER MATERIAL
WCB steel or WC9 chrome moly steel
CF8M (316 SST)
MATERIAL TEMPERATURE CAPABILITY TRIM DESIGNATION FROM TABLE 17
VALVE SIZE, SIZE INCHES
F
C
Min
Max
Min
Max
301
8x6 12 x 6
–20 –20
640 595
–29 –29
338 313
301C (for soft seats)
8 x 6, 12 x 6
–20
400
–29
204
304
8x6 12 x 6
–20 –20
650 640
–29 –29
343 338
313 (NACE compatible)
8x6 12 x 6
–20 –20
450 400
–29 –29
232 204
313C (NACE compatible) (for soft seats)
8x6 12 x 6
–20 –20
400 400
–29 –29
204 204
315
8x6 12 x 6
–20 –20
400 350
–29 –29
204 177
317
8 x 6, 12 x 6
–20
800
–29
427
318 (WCB only)
8 x 6, 12 x 6
–20
800
–29
427
318 (WC9 only)
8 x 6, 12 x 6
–20
1100
–29
593
301, 301C (for soft seats), 304
8x6 12 x 6
–20 –20
300 250
–29 –29
149 121
310
8 x 6, 12 x 6
–325
300
–198
149
313
8 x 6, 12 x 6
–20
600
–29
316
313C (for soft seats)
8 x 6, 12 x 6
–20
400
–29
204
315
8 x 6, 12 x 6
–325
800(1)
–198
427(1)
1. May be used up to 1000 F (538 C) if manufacturing process controls carbon content to 0.04% minimum or 0.08% maximum.
Table 19. Design EWD–1 and EWT–1 Metal Trim Part Combinations for Valves with Whisper Trim III Cages Trim Designation
CA6NM(1)
Cage
Seat Ring
CB7CU-1 (17-4PH SST) with H1025 heat-treat condition
Heat-treated CA6NM
I
Heat-treated
II
S31600 (316 SST) with seat and guide hard faced with CoCr-A
CB7CU-1 with H1025 heat-treat condition
Inconel 600 with seat hard faced with CoCr-A
IV
CF8M (316 SST) with seat and guide hard faced with CoCr-A
CB7CU-1 with H0125 heat-treat condition
CF8M with seat hard faced with CoCr-A
1. CA6NM is similar to 410 SST.
20
Valve Plug
Bulletin 51.1:EW FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °F
WITH STEEL OR CHROME MOLY STEEL VALVE
PRESSURE DROP, BAR
PRESSURE DROP, PSI
PRESSURE DROP, BAR
PRESSURE DROP, PSI
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °F
WITH CF8M (316 SST) VALVE
1
NOTE: 1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
2 MAY BE USED DOWN TO –150°F (–101°C) WITH LEVEL A, B, OR C CAGE, OR WITH LEVEL D CAGE THAT HAS AN 18–8 SST BAFFLE.
B1484–1 / IL
Figure 16. Typical Trim Used in Design EWD-1 Valves with Whisper Trim III Cages
21
Bulletin 51.1:EW FLUID TEMPERATURE, °C
PRESSURE DROP, BAR
PRESSURE DROP, PSI
PRESSURE DROP, PSI
PRESSURE DROP, BAR
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °F
WITH STEEL OR CHROME MOLY STEEL VALVE
FLUID TEMPERATURE, °F 1
NOTE: 1 DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE RATING FOR THE CLASS RATING OF THE BODY MATERIAL USED, EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
WITH CF8M (316 SST) VALVE
2 MAY BE USED DOWN TO –150°F (–101°C) WITH LEVEL A, B, OR C CAGE, OR WITH LEVEL D CAGE THAT HAS AN 18–8 SST BAFFLE.
A2733-1 / IL
Figure 17. Typical Trim Used in Design EWT-1 Valves with Whisper Trim III Cages
22
1
Bulletin 51.1:EW Table 20. Materials and Temperature Limitations for Other Parts
PART
WCB or WC9 valve body LCC valve body WC9 valve body Body-to-bonnet y b lti (see bolting ( t bl 24 table for NACE bolting materials and temperature tem erature limits) CF8M (316 SST) valve bodyy
MATERIAL Min
Max
Min
Max
–20 20
800
–29 29
427
–50 50
700
–46 46
371
–20 20
1100
–29 29
593
–50 50
800
–46 46
427
Steel SA-193-B7M for sour gas
–50
800
–46
427
Steel SA-194-2HM for sour gas
–50
650
–46
343
–425 425
100
–254 254
38
–325 325(1)
800
–198 198(1)
427
–325 325(1)
1200
–198 198(1)
649
Studs
Steel SA-193-B7, or steel SA-193-B7M for sour gas
Nuts
Steel SA-194-2H, or steel SA-194-2M for sour gas
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Studs
Steel SA-193-B16
Nuts
Steel SA-194-7
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Studs Nuts Studs
304 SST SA-320-B8
Nuts
304 SST SA-194-8
Studs
316 SST SA-193-B8M (strain hardened)
Nuts
316 SST SA-194-8M
Studs
316 SST SA-193-B8M
Nuts
316 SST SA-194-8M
Disk (all soft-seat constructions)
PTFE
Std for 4 x 2 thru 12 x 6 inch sizes Std. Design g EWD piston ring g
Std. for 10 x 8 & 12 x 8 inch size; optional for 4 x 2 thru 12 x 6 inch sizes
–100
400
–73
204
–50(2)
800
–46(2)
427
–50(2)
900
–46(2)
482
Oxidizing service—all sizes
–50(2)
1000
–46(2)
538
Nonoxidizing service
–50(2)
1100
–46(2)
593
Graphite (FMS 17F27) Gra hite Graphite FMS 17F39
12 x 8 Class 900 and 12 x 8 Class 600 & smaller
Fluoroelastomer(3) Standard 4 x 2 through 12 x 6 inch Design EWT valve plug lug seal (exce (exceptt valve with Cavitrol III cage) Spring-loaded g Design g EWT or EWT-1 valve plug l seall (6) (standard ( t d d for f 10 x 8 & 12 x 8 inch valve regardless of cage and all 4 x 2 through 12 x 6 inch valves with Cavitrol III cage; optional in 4 x 2 through 12 x 6 inch valves with other than Cavitrol III cages) Valve plug stem and pin Load ring (10 x 8 & 12 x 8 inch Design EWD EWS EWD, EWS, & EWT only) Seat ring, ring bonnet and cage gaskets Spiral wound gaskets
MATERIAL TEMPERATURE CAPABILITY F C
Backup ring
0
400
–18
204
–40
450
–40
232
For use with hydrocarbons
–30
160
–34
71
For use with other fluids
–30
200
–34
93
–100
450
–73
232 427
Ethylene-propylene(4) Nitrile(5)
Seal ring
Carbon-filled PTFE
Backup ring
S41600 (416 SST)
–20
800
–29
Retaining ring
S30200 (302 SST)
–425
1100
–254
593
Seal ring
PTFE with Hastelloy C Spring
–100
450(10)
–73
232(10)
Anti-extrusion rings
PEEK (PolyEtherEtherKetone)
- - -(11)
- - -(11)
–325(1)
1100
–198(1)
593
CB7CU-1 (17-4PH SST)
–150
600
–102
316
N07718 (Inconel(7) 718)
–425
1100
–254
593
N05500 (K-Monel(7))
–400
500
–240
260
FGM (standard)
–325
1100
–198
593
PTFE-coated Monel
–100
300
–73
149
Inconel 600(7)/laminated graphite FGM (standard)
–325
1100
–198
593
S31600 (316 SST)
-continued-
23
Bulletin 51.1:EW Table 20. Materials and Temperature Limitations for Other Parts (Continued)
PART
MATERIAL TEMPERATURE CAPABILITY F C
MATERIAL Min
Max
Min
Max
PTFE V-ring
–40
450
–40
232
PTFE/composition
–100
450
–73
232
Graphite ribbon/filament
–325
1000(9)
–198
538(9)
Graphite ribbon for high-temperature oxidizing service
700
1200
371
649
Packing flange, studs and nuts when used with standard bonnet
S31600
–325(1)
1100
–198(1)
593
Packing follower, and packing spring(8) or lantern ring
S31600
Packing box ring when used with standard bonnet
S31600
–325 325(1)
1100
–198 198(1)
593
Packing (temperatures shown are material temperature capabilities)
Extension bonnet bushing
Trims 1 & 4
S41600
–20
800
–29
427
Other trims
S31600
–325(1)
1100
–198(1)
593
1. May be used down to –425 F (–254 C) if manufacturing process includes Charpy impact test. 2. This minimum is due to thermal expansion differential between piston ring and cage at low temperatures. 3. For high-temperature air, hydrocarbons, and certain other chemicals and solvents, but cannot be used with ammonia, steam, or hot water. 4. Has excellent moisture resistance to hot water and steam and may be used with most fire-resistant hydraulic oils, but cannot be used with petroleum-based fluids and other hydrocarbons. 5. Cannot be used with fire-resistant hydraulic oils. 6. May be used to increase hot water service capability to 450 F (232 C). 7. This material may be used for cyclic temperatures or those above 450 F (232 C). 8. Spring is used only with single PTFE V–ring packing; lantern ring replaces spring in other packings. 9. Except 700 F (371 C) on oxidizing service. 10. If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may be used in temperatures up to 600 F (316 C) for non-oxidizing service or up to 500 F (260 C) for oxidizing service. 11. These materials not limiting factors.
Table 21. Additional Specifications(1)
VALVE SIZE, SIZE INCH
4x2 6 x 4, 8 x 4
PORT DIAMETER
CAGE STYLE
Inch
mm
Inch
mm
Inch
mm
Inch
mm
Inch
mm
29
1/2
12.7
2-13/16
71
3/4
19.1
3-9/16
90
3/4
19.1
3-9/16
90
1
25.4
1-1/4
31.8
5
127
1
25.4
1-1/4
31.8
5
127
5
127
Cavitrol only(1)
4-3/8 4 3/8
111
178
8x6
5-3/8
136
12 x 6
5-3/8
10 x 8
24
Yoke Boss
1-1/8
7
1. 2. 3. 4. 5. 6. 7.
Stem
59
8 x 6, 12 x 6
Class 900
Optional
Yoke Boss
mm
178
Class 900
Stem
Inch
7
12 x 8
Standard
2-5/16
8 x 6, 6 12 x 6
Class 300(4) or 600(4)
STEM AND YOKE BOSS DIAMETERS
VALVE PLUG TRAVEL
2
51
1/2
12.7
2-13/16 2 13/16
71
2
51
3/4
19 1 19.1
3 9/16 3-9/16
90
3
76
3/4
19 1 19.1
3 9/16 3-9/16
90
4(2)
102(2)
3/4
19.1
3-9/16
5(3)
127(3)
136
6-1/2(3)
165(3)
3/4
19 1 19.1
8
203
3
76
3/4
8
203
3
76
8 7-3/4(6) or 6-3/4(7)
203 197(6) or 172(7)
3
6
76
152
Quick-opening, linear, equal percentage, ercentage, Whisper Trim I,, or C it l(1) Cavitrol
1
25.4
1-1/4
31.8
90
---
---
---
---
Whisper Trim I only
3 9/16 3-9/16
90
1
25 4 25.4
5
127
Whisper Trim III only
19 1 19.1
3 9/16 3-9/16
90
5
127
Quick o ening, linear, Quick-opening, equal percentage only
3/4
19 1 19.1
3 9/16 3-9/16
90
5
127
1
25 4 25.4
3-9/16
90
1-1/4
31.8
1-1/4
31.8
5
5
127
127
Except for Cavitrol III cages, which are covered in separate documentation. Bonnet spacer required. This travel available only in Class 300 or 600 Design EWD or EWT valve. Bonnet spacer required for Design EWD or EWT valve but not for Design EWS valve. Bonnet spacer required for Design EWD, EWS, and EWT valve. H indicates heavy actuator-to-bonnet bolting is required. Port diameter for level A, B, or C cage. Port diameter for level D cage.
1
25.4
1-1/4
31.8
1
25.4
1-1/4
31.8
3/4
19.1
1
25.4
1-1/4
31.8
5H(5) ---
Quick-opening, Quick opening linear linear, or equal percentage only
127H(5 )
Whisper Trim III only
Bulletin 51.1:EW PACKING BOX STUD
SPRING
FOLLOWER PACKING
W5801–3 / IL A7018 / IL
PACKING BOX STUDS
PACKING BOX STUD SPRINGS
SPRINGS
ANTI– EXTRUSION RING
PACKING RING
PACKING FOLLOWER VALVE BONNET
VALVE BONNET
LANTERN RING
W5805–5 / IL W5803–3 / IL
Figure 18. Typical ENVIRO-SEAL and HIGH-SEAL Packing Systems
25
Bulletin 51.1:EW Table 22. Approximate Weights VALVE SIZE, INCHES 4x2
END CONNECTION
Class 900
8x6
12 x 6
10 x 8
12 x 8
kg
Lb
kg
Lb
kg
Lb
kg
Lb
kg
Lb
kg
Lb
kg
185
84
330
150
515
234
625
284
1102
500
1250
567
1440
653
Flanged
220
100
430
195
600
272
680
308
1590
721
1640
744
1890
857
Buttwelding
135
61
270
122
390
177
600
272
1160
526
1130
512
1450
658
Flanged
---
1350
612
---
3000
1361
Buttwelding
---
1000
454
---
2850
1293
W5852–1/IL
Figure 19. ENVIRO-SEAL Bellows Seal Bonnet
26
8x4
Lb Class 300 Class 600
6x4
Bulletin 51.1:EW Table 23. Bonnet Selection Guidelines BONNET STYLE (CLASS 300, 300 600)(1)
IN-BODY PROCESS TEMPERATURE LIMITS(2)
PACKING F
C
Plain Bonnet Standard for 2-, 4-, and 6-inch nominal trim sizes Standard for 10 x 8 and 12 x 8-inch 8 inch valves (in cast iron, WCB). Not available in S31600
PTFE V-ring
0 to 450
–18 to 232
PTFE/composition
0 to 450
–18 to 232
Graphite ribbon/filament
0 to maximum shown in table 20
0 to maximum shown in table 20
Style 1 Cast Extension Bonnet O Optional tional for 2-, 4-, and 6-inch nominal trim sizes Standard for 10 x 8 and 12 x 8 inch valves (in S31600). Optional in WCB; not available in cast iron
PTFE V-ring –50 to 0 and above 450
–46 to 18 and above 232
Style 2 Cast Extension Bonnet O Optional tional for 2-, 4-, and 6-inch nominal trim sizes O Optional tional for 10 x 8 and 12 x 8-inch 8 inch valves (in WCB). Not available in cast iron or S31600
PTFE V-ring –150 to 0 and above 450
–101 to –18 and above 232
ENVIRO-SEAL bellows seal bonnet O Optional tional for 2-, 4-, 6-, and 8-inch nominal trim sizes. Maximum travel is 2 inches
PTFE
PTFE/composition Graphite ribbon/filament
PTFE/Composition Graphite ribbon/filament
For exceptional stem sealing capabilities. See Bulletin 59.1:070, 59 1:070 ENVIRO-SEAL ENVIRO SEAL Bellows Seal Bonnets, for pressure/temperature ratings.
Graphite
1. For Class 900 valve bodies, only the plain bonnet is available. Contact your Fisher Controls sales representative or sales office for assistance if application conditions indicate the need for an extension bonnet for a Class 900 valve body. 2. These in-body process temperatures assume an outside, ambient temperature of 70 F (21 C). When using any packing at low process temperatures, a cast extension bonnet may have to be used to prevent packing damage which could result from the formation of valve stem frost.
Table 24. Bolting Materials and Temperature Limits for Bolting Compliance with NACE Specification MR0175 TEMPERATURE CAPABILITIES
VALVE BODY MATERIAL
BOLTING MATERIAL
F Min
C Max
Min
Max
20
450
–7 7
232
450
800
232
427
–50 50
450
–46 46
232
450
800
232
427
–50 50(1)
450
–46 46(1)
232
450
650
232
343
NACE (non-exposed bolting) (Standard)
WCB
CF8M (316 SST)
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H
Studs
Steel SA-193-B7
Nuts
Steel SA-194-2H lubricated
Studs
Steel SA-193-B7 or B8M strain hardened
Nuts
Steel SA-194-2H or 8M
Studs
Steel SA-193-B8M strain hardened or B7
Nuts
Steel SA-194-8M lubricated or 2H lubricated
NACE (exposed bolting) (Optional) No Derating of Valve Required WCB and CF8M
Studs
Steel SA-564-630 (H1150 dbl(2))
Nuts
Steel SA-194-2HM dbl(2))
Studs
Steel SA-564-630 (H1150
Nuts
Steel SA-194-2HM lubricated
NACE (exposed bolting) (Optional) Requires Derating of Valve(3) When These Body-to-Bonnet Bolting Materials are Used WCB and CF8M
Studs
Steel SA-193-B7M
Nuts
Steel SA-194-2HM
Studs
Steel SA-193-B7M
Nuts
Steel SA-194-2HM lubricated
–50 50(1)
450
–46 46(1)
232
450
800
232
427
1. Minimum temperature is –20 F (–29 C) with WCB valve body material. 2. Special heat treating required. 3. Derating is not required for ANSI Class 300 valves. Derating may be required for valves rated at ANSI Class 600 or 900. Contact your Fisher Controls sales office or sales representative for assistance in determining the derating of valves when these body-to-bonnet bolting materials are used.
27
Bulletin 51.1:EW
A(1)
G (MAX)
Class, End Connection Style(2)
VALVE SIZE, INCHES
RF
RTJ
RF, BW
RTJ
4x2 6x4 8x4 8x6 8 x 6 w/10’’ Ends
14.50 18.62 22.38 22.38 23.75
15.12 19.25 23.00 23.00 24.38
15.50 20.00 24.00 24.00 24.62
15.62 20.12 24.12 24.12 24.75
12 x 6 10 x 8 12 x 8
30.50 27.88 30.50
31.12 28.50 31.12
32.25 29.62 32.25
4x2 6x4 8x4 8x6 8 x 6 w/10’’ Ends
368 473 568 568 603
384 489 584 584 619
12 x 6 10 x 8 12 x 8
775 708 775
791 724 791
Class 300
Class 600
Class 900 RTJ
BW
Class 300, 600
Class 900
------36.00 ---
------36.12 ---
------38.25 ---
4.25 5.31 6.94 7.19 7.19
------7.81 ---
32.38 29.75 32.38
----35.50 mm
----35.62
----37.50
10.00 10.81 14.00
----14.00
394 508 610 610 625
397 511 613 613 629
------914 ---
------917 ---
------972 ---
108 135 176 183 183
------198 ---
819 752 819
822 756 822
----902
----905
----953
254 275 356
----356
RF Inch
1. Per ANSI B16.10 and FCI 65-2 for Class 300 and 600 only. 2. End connection style abbreviations: RF - Raised Face, RTJ - Ring Type Joint, BW - Buttwelding.
MATCH LINE FOR ACTUATOR
MATCH LINE FOR ACTUATOR
AV7029–K A0921–1 / IL
TYPICAL OF 4 X 2 THROUGH 10 X 8 INCH SIZES (INCLUDING 12 X 6 INCH SIZE)
Figure 20. Dimensions
28
15A9682–C A6108–1 / IL
TYPICAL OF 12 X 8 INCH SIZE
Bulletin 51.1:EW DIMENSION D FOR ALL VALVE SIZES STEM DIA CAGE STYLE
BONNET
Whisper
1/2 Inch (12.7 mm)
1 Inch (25.4 mm) or 1-1/4 Inch (31.8 mm)
3/4 Inch (19.1 mm) Class 900 Only
All Except Class 900
Class 300 & 600
Class 900
Inch
mm
Inch
mm
Inch
mm
Inch
mm
Inch
mm
Plain
4x2 6x4 8x4 8x6 12 x 6 10 x 8 12 x 8
8.50 10.12 10.19 11.31 14.00 -----
216 257 259 287 356 -----
------16.12 ----23.00
------409 ----584
8.38 10.00 10.06 11.31 14.00 14.75 16.19
213 254 256 287 356 375 411
--11.81 11.88 13.06 15.75 -----
--300 302 332 400 -----
------18.25 ----23.94
------464 ----608
Style 1 extension
4x2 6x4 8x4 8x6 12 x 6 10 x 8 12 x 8
12.50 14.12 14.19 ---------
317 359 360 ---------
---------------
---------------
12.69 14.31 14.38 15.50 18.19 16.56 18.00
322 363 365 394 462 421 457
--17.00 17.06 18.25 20.94 17.69 19.12
--432 433 464 532 449 486
---------------
---------------
Style 2 extension
4x2 6x4 8x4 8x6 10 x 8 12 x 6 12 x 8
20.31 22.12 22.19 ---------
516 562 564 ---------
---------------
---------------
20.19 21.81 21.88 22.81 24.44 25.50 ---
513 554 556 579 621 648 ---
--23.44 23.50 ---------
--595 597 ---------
---------------
---------------
ENVIRO-SEAL bellows seal bonnet
4x2 6x4 8x4 10 x 8 8x6 12 x 6 12 x 8
17.12 22.69 22.75 ---------
435 576 578 ---------
---------------
---------------
--22.69 22.75 27.69 23.94 26.62 ---
--576 578 703 608 676 ---
---------------
---------------
---------------
---------------
Plain
4x2 6x4 8x4 8x6 10 x 8(1) 10 x 8(2) 12 x 6 12 x 8
9.94 13.62 13.69 15.88 ----18.88 ---
252 346 348 403 ----480 ---
-----------------
-----------------
9.81 13.50 13.56 15.88 14.75 20.12 18.88 ---
249 343 344 403 375 511 480 ---
--15.31 ----16.75 22.06 -----
--389 ----425 560 -----
-----------------
-----------------
Plain
8x6 12 x 6 12 x 8
-------
-------
-------
-------
15.69 19.81 ---
398 503 ---
17.44 21.56 ---
443 548 ---
-------
-------
All except Cavitrol III or Whisper Trim III
Cavitrol III
VALVE SIZE SIZE, INCH
1. One-stage trim. 2. Two-stage trim.
Figure 20. Dimensions (Continued)
29
Bulletin 51.1:EW
This product may be covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or under pending patents. Cavitrol, easy-e, ENVIRO-SEAL, HIGH-SEAL, Whisper Trim, Fisher, Fisher-Rosemount, and Managing The Process Better are marks owned by Fisher Controls International, Inc. or Fisher-Rosemount Systems, Inc. C-seal is a mark owned by Pressure Science, Inc. All other marks are the property of their respective owners. Fisher Controls International, Inc. 1973, 1998; All Rights Reserved
For information, contact Fisher Controls: Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 30
Printed in U.S.A.