PRO3200 Professional Modular Access Control Hardware
PRO3200 Access Control Hardware
PRO3200 Modules
As a part of the WIN-PAK software controlled hardware family the
The PRO3200 professional series family of access control modules
PRO3200 professional modular access control hardware is an
is connected to an interface with the main controller (PRO32IC)
advanced access control panel capable of providing solutions where
through a supervised RS485 bus. Hardware interface
installation space is at a premium. The design of the hardware is
configuration options are stored in the main controller and may be
modular and flexible and can be tailored to meet a wide range of
directly controlled via operator intervention, time schedules or
applications, while optimising cost and mounting space.
event-based procedures. The modules have been designed to
®
The PRO3200 system is connected to a host computer with WIN-
allow for a modular customisable solution.
PAK for system configuration, alarm monitoring and direct control.
PRO3200 Reader Modules
Using WIN-PAK SE 4.0 / PE 4.0 or higher, at least 255 PRO3200
The PRO32R2 supports two card access readers to control two
systems can be connected to create large access control solutions.
doors. In the event that communication to the intelligent control
Every PRO3200 consists of a main controller, one or more
module is lost, the card access readers can be individually
enclosures, power supplies and reader or I/O modules. A PRO3200
configured to allow entrance based on security needs.
system can be set up as an access control system with up to 32
This customisation allows for a door to be configured as locked,
doors, protected with one reader each door. If additional inputs and
unlocked or access only via a valid facility code.
outputs are needed for extra control within the PRO3200 system, the number of controllable doors will be limited to less than 32 doors. The access control limitations depend on the amount of extra controllable inputs and outputs needed within the modular configuration of up to 16 I/O or reader boards.
PRO3200 I/O Modules The PRO32OUT module provides 12 Form C, 12 VDC, 2A relay output controls when mounted in a high density rack mount enclosure (PRO22ENC1 and PRO22ENC2). If the board is tile mounted in a PRO22ENC3, four extra Form C, 12 VDC, 2A relay
Designed to fit into tight spaces, the PRO3200 with its rack-mount
output controls and power fail and panel tamper inputs are
design provides high-density installations for up to 16 doors per
provided. Relays may be used for lift control, status annunciation
cabinet in a small space. The design makes it ideal for applications
and for general facility control.
where eight or more doors are needed. Metal enclosures for up to two modules are available for remote located controllable doors, connected via a supervised RS485 bus.
The PRO32IN module provides 16 supervised alarm inputs and a dedicated power fail and panel tamper when tile mounted. The inputs can be supervised with end-of-line resistors or non-
PRO3200 Main Controller
supervised (digital). Inputs may be used for status and for general
The PRO3200 main controller board (PRO32IC) accommodates a
facility monitoring, such as door monitoring.
card database of 100,000 cards, a transaction buffer of 50,000 transactions and is designed to operate off-line, making access control decisions independently from a PC or other controlling devices.
Enclosures for PRO3200 devices The PRO3200 main controller and modules are designed to accommodate various mounting options. Units can be mounted in a
The PRO32IC supports any combination of up to 16 I/O or reader
high-density rack configuration (PRO22ENC1 and PRO22ENC2)
boards to monitor alarm input points, relay output points and access
when space is limited or in a tile-mount configuration (PRO22ENC3)
control reader interface points. Connectivity to the host computer with
for remotely located doors and I/O. A high-density enclosure can
WIN-PAK SE 4.0 / PE 4.0 or higher is accomplished via on board
facilitate a power supply, a main controller and up to eight modules.
Ethernet port, serial (RS232) communication or dial-up modem.
• PRO22ENC1 is a wall-mounted high-density enclosure • PRO22ENC2 is a 19" rack-mounted high-density enclosure • PRO22ENC3 is a wall-mounted remote enclosure for up to two modules or main controllers
PRO3200 Professional Modular Access Control Hardware
S Y S T E M F E AT U R E S • Configurable via WIN-PAK SE 4.0 / PE 4.0 or higher access control software • At least 225 PRO3200 systems
• Supervised communication and lithium battery backup ensures system reliability • Large, local controller database allows
• Any combination of 16 I/O or reader modules may be connected to the PRO32IC RS485 ports at 38,400 bps.
configurable in a WIN-PAK hosted system
access control decisions to be made by
1250m total bus length per port.
to meet the needs of large access control
controller in real time without the need to
• Accommodates a card database of
and security systems
communicate to the server
• Scalable architecture ensures optimal
• Seamless support for TCP/IP protocols to
performance with a seamless upgrade
allow intelligent controller(s) to tap into a
path to accommodate future growth
LAN or WAN
beyond its initial installation • Rack or tile mounting options available
• True 32-bit microprocessor provides fast transaction processing for the most demanding network applications
100,000 cards, and a transaction buffer of 50,000 transactions • Option to include or exclude fields during database configuration to maximise memory usage • Automatic calculation of leap-year and daylight savings
A C C E S S C O N T R O L F E AT U R E S • Supports a wide range of reader
• Configurable as fail-secure (energise
technologies including Wiegand, magnetic
to activate) or fail-safe (de-energise
stripe, proximity, smart card and keypad
to activate)
• Supports multiple reader and card formats for maximum flexibility and security options • System off-line modes customisable per reader include facility code access, locked (no access) and unlocked (full access) • Operating modes include locked, unlocked, facility code, card only, card and PIN, card or PIN and PIN only
• Activation and deactivation dates by card • Up to 12 intervals per time zone where each interval is a start time, stop time and
• Up to eight card formats per reader
day map. The day map indicates the day
• Anti-passback support
of the week or holiday
• Up to 32 access levels per card or individual time zones per readers • 10-digit (32-bit) user ID standard / 15-digit maximum
• 255 possible holidays are defined by a starting date and duration • Entire card bit-stream reported with invalid facility code or invalid card format
• Personal Identification Number (PIN) with up to eights digits
I N P U T / O U T P U T C O N T R O L F E AT U R E S • User programmable relay outputs allow for specific control needs • Pulse control: single pulse (up to 255 seconds) or repeating pulses (on/off in 1 second increments, up to 255 times)
• Configurable as standard, entry delay
• Alarm circuit type - normally open,
latching, entry delay non-latching and
normally closed, non-supervised,
exit delay
supervised (with correct EOL). Meets
• User programmable alarm inputs offer
requirements for UL294 and CUL
flexible system configuration and control
E N C L O S U R E F E AT U R E S • User programmable relay outputs allow for specific control needs • Pulse control: single pulse (up to 255 seconds) or repeating pulses (on/off in 1 second increments, up to 255 times)
• Configurable as standard, entry delay
• Alarm circuit type - normally open,
latching, entry delay non-latching and
normally closed, non-supervised,
exit delay
supervised (with correct EOL). Meets
• User programmable alarm inputs offer flexible system configuration and control
requirements for UL294 and CUL
S Y S T E M S P E C I F I C AT I O N S Database:
Access Modules:
Enclosures:
• Flash programming for firmware
• 16 total devices/modules available per
• PRO22ENC1 (Wall-mount)
revision updates • Memory for 100,000 cards
PRO32IC controller • PRO3200 modules available:
• Memory for 50,000 events
- Dual reader module (PRO32R2)
• Access codes: Unlimited
- 16 relay output module (PRO32OUT)
• Holidays: Unlimited
- 16 alarm input module (PRO32IN)
• Time codes: 255, 64 supported by WIN-PAK
• Backward compatible with PRO2200
Capacity: nine modules. Power supply and battery not included • PRO22ENC2 (19" Rack-mount) Capacity: nine modules. Power supply and battery not included • PRO22ENC3 (Tile-mount)
modules:
Capacity: Two modules. Battery included.
• Card reader formats: eight per reader
- Single reader module (PRO22R1)
Recommended Power Supply: PSX220
• Credential facility codes: eight
- Dual reader module (PRO22R2)
Transformer 240VAC / 16VAC
• Lift support: 240 floors (relays)
- 16 relay output module (PRO22OUT)
Dimensions:
• Dedicated tamper alarm
- 16 alarm input module (PRO22IN)
• PRO3200 Board: 22.86 cm H x 13.97 cm
• Dedicated power fail alarm • Real time clock: - Geographic time zone support
• Module connectivity via RS485 protocol (1250m)
- Daylight Saving Time
Access Control Operational Functionality:
- Leap year support
• Duress detection
- 4-bit parallel accurate to 50 ppm
• Operational modes:
• Precision access groups/levels
- Card only
• Multiple access groups/levels
- PIN only
Communication: • Primary communication support: - On board Ethernet (TCP/IP) - RS232 - Dial-up modem* • Communication speed: 38.4 Kbps • Automatic dial back: - Dial-back on alarm condition - Dial-back on transaction buffer capacity reached - Dial-back on primary power loss • Download functionality: - System functional during system download: Yes - System functional during credential download: Yes *Requires additional hardware
W x 2.54 cm D • PRO22ENC1: 35.3 cm H x 43.18 cm W x 22.86 cm D • PRO22ENC2: 35.3 cm H x 48 cm W x 22.86 cm D • PRO22ENC3: 35.56 cm H x 40.64 cm W x 10.2 cm D
- Card or PIN
Environment:
- Card and PIN
• Temperature: 0°C to 49°C operational;
- Facility code only • Maximum PIN size: 8 digits • Door object support • Two person access rule • Offline modes (selectable per reader): - Facility code access - Locked (no access) - Unlocked (free access) • Anti-Passback support via RS485 modules: - While preventing access (hard) - While allowing access (soft) • Transaction prioritisation: 99 levels
-55°C to 85°C storage • Humidity: 0 to 85% RHNC
Wiring Requirements: • Power - twisted pair, 18 AWG • RS485 - 24 AWG, 1,200m max, two twisted pairs with shield (120 W, 23 pF, Belden 9842 or equivalent) • RS232 - 24AWG, 7.6 m max • Alarm input - twisted pair, 30 ohms max
PRO3200 Professional Modular Access Control Hardware
M O D U L E S P E C I F I C AT I O N S Reader Modules PRO3200 Series Dual Reader Module (PRO32R2) Module Specifications Port
2 reader ports - 12 VDC at 50 mA, clock / data or data0 / data1
Keypad
Keypad multiplexed with card data
Wire Support
Two-wire or one-wire bi-colour LED support
Buzzer Support
Buzzer support only with one-wire LED control 4 supervised, door status and egress inputs and 2 general purpose alarm inputs with programmable circuit type (2 additional supervised inputs available when using PRO22ENC3 enclosure)
Door Alarm Inputs Alarm Inputs
2 dedicated alarm inputs for tamper detection and power loss
Door Control Relays Output Relays
2 general purpose output relays, form C, 5 A 28 VDC 2 general purpose output relays, form C, 2 A 28 VDC (2 additional output relays available when using PRO22ENC3 enclosure)
Alarm Input Properties Inputs
Inputs may be assigned to door related functions or general purpose I/O Circuit type - normally open, normally closed, non-supervised, supervised (with standard 1K or custom end-of-line resistance 200-10K)
Circuit Type Line Conditioning
Line conditioning - programmable sensitivity and hold time
Output Control Properties Outputs
Outputs may be assigned to door related functions or general purpose I/O
Relay Rating
The 5 A relay(s) are rated to handle the inductive loads of door locking devices
Configurable
Configurable as fail-secure (energise to activate) or fail-safe (de-energise to activate)
Pulse Time
1-32,400 seconds, 1-255 for door relays
RS485 Port
RS485 port, 1,250m total bus length
Default Speed
38.4 Kbps
I/O Modules PRO3200 Series 16 Relay Output Module (PRO32OUT) Module Specifications Alarm Inputs
2 dedicated alarm inputs for tamper detection and power loss (tile-mounted only)
Alarm Inputs Output Relays
PRO3200 Series 16 Alarm Input Module (PRO32IN)
N/A
16 general purpose inputs with programmable circuit type
12 general purpose output relays, form C, 2 A 30 VDC (four additional are available when using PRO22ENC3 enclosure)
1 general purpose, form C, 2 A 30 VDC relay (one additional is available when using PRO22ENC3 enclosure)
Output Control Properties Outputs
All 16 relay outputs (mounted in PRO22ENC3) or 12 relay outputs (in PRO22ENC1 and PRO22ENC2) are available for general purpose I/O
Both relay outputs are available for general purpose I/O
The 2 A relays are rated to handle dry circuit logic
Both relay outputs are rated to handle dry circuit logic
Dry Circuit Logic Pulse Time Configurable
1-32,400 seconds Configurable as fail-secure (energise to activate) or fail-safe (de-energise to activate)
N/A
Alarm Input Properties Inputs
N/A
All 16 inputs may be assigned to door related functions or general purpose I/O
Circuit Type
N/A
Circuit type - normally open, normally closed, non-supervised, supervised (with correct EOL)
Line Conditioning
N/A
Line conditioning - programmable sensitivity and hold time
Communication Features Measurements Default Speed
RS485 port, 1250m total bus length per port 38.4 Kbps
T Y P I C A L S Y S T E M C O N F I G U R AT I O N
PRO22ENC1 and PRO22ENC2 Module
PRO22ENC3
Reader
Inputs
Outputs
Inputs
PRO32R2
2
6
4
10**
6
PRO32OUT
0
0
12
2**
16
PRO32IN
0
16
1
18**
2
**Two are used to monitor Power and Tamper PRO22ENC1 and PRO22ENC2=9 Board Capacity / PRO22ENC3=2 Board Capacity
Outputs
PRO3200 Professional Modular Access Control Hardware
ORDERING PRO3200 Controllers and Modules
PRO3200 High Density Enclosures and Accessories
PRO32IC
PRO3200 Intelligent Controller
PRO22ENC1
PRO32R2
PRO3200 Dual Reader Module
power supply, main controller and up to
PRO32OUT
PRO3200 16* Relay Output Module
eight modules. Power supply and battery
PRO32IN
PRO3200 16 Alarm Input Module
not included PRO22ENC2
modules. Power supply and battery not
(add PRO3200 Modules to complete configuration)
included
PRO3200 Kit , including PRO32IC, PRO22ENC1, PRO32E1PS, PRO22BAT1,
PRO32E1PS
PRO22DCC
PRO3200 Kit , including PRO32IC,
PRO3200 power/communication daisy chain harness
PRO22ENC2, PRO32E1PS, PRO22BAT1, PRO22DCC
110V/240VAC - 12VDC /4 A rack-mounted power supply with battery backup
PRO22DCC PRO32E2EN
19" Rack-mount, high-density enclosure for power supply, main controller and up to eight
PRO3200 High Density Enclosure kit
PRO32E1EN
Wall-mount, high-density enclosure for
PRO3200 Remote Enclosure and Accessories PRO22ENC3
Wall-mount enclosure with battery for two modules. Power supply not included
PSX220 * Only 12 relay outputs are available when using the PRO22ENC1 and PRO22ENC2 enclosures
For additional information, please visit www.honeywell.com/security/uk Honeywell Security Group Aston Fields Road Whitehouse Industrial Estate Runcorn Cheshire WA7 3DL Tel: 08448 000 235 www.honeywell.com
HAS-PRO3200-01-UK(0514)DS-E May 2014 © 2014 Honeywell International Inc.
240VAC / 16VAC transformer