TIBTRONIX TECHNOLOGY CO., LTD.
TSPL1G80D 1.25Gb/s 80km SFP Transceiver Hot Pluggable, Duplex LC, +3.3V, 1550nm, DFB-LD, Single-mode, DDM
2013/6/1
Shenzhen Tibtronix Technology Co., Ltd. 5/F, 9th Building , Jiuxiangling Industrial Zone, Xili, NanShan District, Shenzhen, China Tel: +86 755 83129772
Fax: +86 755 83129773
E-mail: sales@tibtronix.com
http://www.tibtronix.com
TSPL1G80D
Features: �
Up to 1.25Gb/s Data Links
�
Hot-Pluggable
�
Duplex LC connector
� Up to 80km on 9/125μm SMF �
1550nm DFB laser transmitter
� Single +3.3V Power Supply � Monitoring Interface Compliant with SFF-8472 � Maximum Power <1W � Industrial /Extended/ Commercial operating temperature range: -40°C to 85°C/-5°C to 85°C/-0°C to 70°C Version available � RoHS compliant and Lead Free
Applications: �
Metro/Access Networks
�
1.25 Gb/s 1000Base-ZX Ethernet
�
1×Fibre Channel
� Other Optical Links �
Description: TIBTRONIX’s TSPL1G80D Transceiver is a high performance, cost effective module which have a duplex LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control and monitor signals. The receiver section uses a PIN receiver and the transmitter uses a 1550 nm DFB laser, up to 22dB link budge ensure this module 1000Base Ethernet 80km application.
2
TSPL1G80D
� Absolute Maximum Ratings Parameter
Symbol
Min Min..
Typical
Max Max..
Unit
Storage Temperature
TS
-40
+85
°C
Supply Voltage
VCC
-0.5
4
V
Relative Humidity
RH
0
85
%
� Recommended Operating Environment: Parameter
Symbol Industrial
Case operating Temperature
Extended
TC
Commercial
Min Min..
Typical
Max Max..
Unit
-40
85
°C
-5
85
°C
0
+70
°C
3.135
3.465
V
Supply Voltage
VCC
Supply Current
Icc
300
mA
Inrush Current
Isurge
Icc+30
mA
Maximum Power
Pmax
1
W
C, VCC = 3. 135 to 3. 465 Volts) � Electrical Characteristics(TOP = -40 to 85 85°C, 3.135 3.465 Parameter
Symbol
Min Min..
Typical
Max Max..
Unit
Note
Transmitter Section: Input differential impedance
Rin
90
Single ended data input swing
Vin PP
Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time
110
W
250
1200
mVp-p
VD
Vcc – 1.3
Vcc
V
VEN
Vee
Vee+ 0.8
V
10
us
Tdessert
100
1 2
Receiver Section: Single ended data output swing
Vout,pp
250
800
mv
3
LOS Fault
Vlosfault
Vcc – 0.5
VCC_host
V
5
LOS Normal
Vlos norm
Vee
Vee+0.5
V
5
PSR
100
mVpp
6
Power Supply Rejection Note: 1. AC coupled.
3
TSPL1G80D
2. 3.
Or open circuit. Into 100 ohm differential termination.
4. 5. 6.
20 – 80 % LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.
C, VCC = 3. 135 to 3. 465 Volts) 85°C, 3.135 3.465 � Optical Parameters(TOP = -40 to 85 Parameter
Symbol
Min Min..
Typical
Max Max..
Unit
Note
Transmitter Section: Center Wavelength
λc
Spectral Width
σ
Side Mode Suppression Ratio
1530
SMSR
30
Optical Output Power
Pout
-2
Extinction Ratio
ER
8.2
1550
1570
nm
1
nm dB
+3
dBm dB
Optical Rise/Fall Time
tr / tf
260
ps
Relative Intensity Noise
RIN
-120
dB/Hz
Output Eye Mask
1 2
Compliant with IEEE802.3 z (class 1 laser safety)
Receiver Section: Optical Input Wavelength
λc
1270
Receiver Overload
Pol
-3
RX Sensitivity
Sen
RX_LOS Assert
LOS A
RX_LOS De-assert
LOS D
RX_LOS Hysteresis
LOS H
1610 -24
-35
nm dBm
4
dBm
4
dBm -25
0.5
dBm dB
General Specifications: Data Rate
BR
Bit Error Rate
BER
Max. Supported Link Length on 9/125μm SMF@1.25Gb/s
LMAX
Total System Budget
LB
1.25
Gb/s 10-12
80 22
km dB
Note 1. The optical power is launched into SMF. 2. 20-80%. 3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253. 4
TSPL1G80D
4. Measured with PRBS 27-1 at 10-12 BER
� Pin Assignment Diagram of Host Board Connector Block Pin Numbers and Name
Diagram of Host Board Connector Block Pin Numbers and Names
� Pin Function Definitions Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Name VeeT TX Fault TX Disable MOD-DEF2 MOD-DEF1 MOD-DEF0 Rate Select LOS VeeR VeeR VeeR RDRD+ VeeR VccR
Function Transmitter Ground Transmitter Fault Indication Transmitter Disable Module Definition Module Definition 1 Module Definition 0 Not Connected Loss of Signal Receiver Ground Receiver Ground Receiver Ground Inv. Received Data Out Received Data Out Receiver Ground Receiver Power
Plug Seq 1 3 3 2 3 3 3 3 1 1 3 3 3 2
Notes 1 2 3 3 3 4 5 1 1 1 6 6 1 1 5
TSPL1G80D
16 17 18 19 20
VccT VeeT TD+ TDVeeT
2 1 3 3 1
Transmitter Power Transmitter Ground Transmit Data In Inv. Transmit In Transmitter Ground
6 6
Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Rate select is not used 5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 6. AC Coupled
� SFP Module EEPROM Information and Management The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated. Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)
A0h Table 2 - EEPROM Serial ID Memory Contents (A0h A0h) Data Length Name of
Description and Contents 6
TSPL1G80D
Address (Byte) Base ID Fields 0 1 1 1 2 1 3-10 8 11 1 12 1 13-14 2 15 1 16 1 17 1 18 1 19 1 20-35 16 36 1 37-39 3 40-55 16 56-59 4 60-62 3 63 1 Extended ID Fields 64-65 2 66 67 68-83 84-91 92-94 95
1 1 16 8 3 1
Vendor Specific ID Fields 96-127 32 128-255 128
Length Identifier Reserved Connector Transceiver Encoding BR, Nominal Reserved Length(9um) Length(50um) Length(62.5um) Length(Copper) Reserved Vendor Name Reserved Vendor OUI Vendor PN Vendor rev Reserved CCID Option BR, max BR, min Vendor SN Date code Reserved CCEX
Readable Reserved
Type of Serial transceiver (03h=SFP) Extended identifier of type serial transceiver (04h) Code of optical connector type (07=LC) NRZ(03h) Nominal baud rate, unit of 100Mbps (0000h) Link length supported for 9/125um fiber, units of 100m Link length supported for 50/125um fiber, units of 10m Link length supported for 62.5/125um fiber, units of 10m Link length supported for copper, units of meters SFP vendor name: TIBTRONIX SFP transceiver vendor OUI ID Part Number: “TSPL1G80D” (ASCII) Revision level for part number Least significant byte of sum of data in address 0-62 Indicates which optical SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported) Upper bit rate margin, units of % Lower bit rate margin, units of % Serial number (ASCII) TIBTRONIX’s Manufacturing date code Check code for the extended ID Fields (addresses 64 to 94) TIBTRONIX specific date, read only Reserved for SFF-8079
� Digital Diagnostic Monitor Characteristics 7
TSPL1G80D
Data Address 96-97 100-101
Parameter Transceiver Internal Temperature Laser Bias Current
Accuracy ±3.0 ±10
°C %
100-101 100-101 100-101
Tx Output Power Rx Input Power VCC3 Internal Supply Voltage
±3.0 ±3.0 ±3.0
dBm dBm %
Unit
� Regulatory Compliance The TSPL1G80D complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following). Electrostatic Discharge (ESD) to the Electrical Pins Electrostatic Discharge (ESD) to the Duplex LC Receptacle Electromagnetic Interference (EMI) Laser Eye Safety
MIL-STD-883E Method 3015.7 IEC 61000-4-2 GR-1089-CORE FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2
Class 1(>1000 V) Compatible with standards Compatible with standards
Compatible with Class 1 laser product.
� Recommended Circuit SFP Module
Host Board VCC (3.3V)
VCCT 4K7 to10KΩ
TX_Disable TX_Fault Z=50Ω
PECL
Z=50Ω
100Ω
Laser Driver
Z=50Ω
PECL
100Ω
Z=50Ω
Amplifer
RX_LOS 4K7 to10KΩ VCC (3.3V) 3X4K7 to10KΩ
MOD_DEF(2) MOD_DEF(1)
EEPROM
MOD_DEF(0) RGND
SFP Host Recommended Circuit 8
TSPL1G80D
ďż˝ Mechanical Dimensions
Mechanical Drawing
TIBTRONIX reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information. Published by Shenzhen TIBTRONIX Technology Co., Ltd. Copyright Š TIBTRONIX All Rights Reserved
9