Sika everbuild schonox catalogue 2015 by Sika Everbuild

| Floor Adhesives And Levelling Compounds Catalogue 2015 |

n Levelling

Compounds

n Primers

& DPMs

n Adhesives n Ancillaries

Distributed by

www.everbuild.co.uk

LEVELLING COMPOUNDS SCHÖNOX® LC POWDER & LIQUID SCHÖNOX® ZM RAPID SCHÖNOX® FPL PLUS SCHÖNOX® AP GYPSUM SCHÖNOX® APF GYPSUM

ADHESIVES 6 8 9 10 11

PRIMERS & DPMS SCHÖNOX® VD SCHÖNOX® SHP SCHÖNOX® SDG DPM SIKA® PRIMER MB

INTRO The SCHÖNOX® name is synonymous with quality products for the building and renovation industry and has been for many years, as well as being one of the leading suppliers to the German and French markets. The company develops and manufactures quality products for installing all types of floor tiles and coverings for professionals. The range includes levelling compounds, floor adhesives, primers and waterproof membranes under the Schönox® brand name.

14 15 17 18

SCHÖNOX® IFLOOR® SCHÖNOX® EMICLASSIC SCHÖNOX® UNITECH SCHÖNOX® PU 900 SCHÖNOX® MULTI OBJEKT SCHÖNOX® DUROCOLL SCHÖNOX® TACKIFIER

21 22 23 24 25 26 27

ANCILLARIES 5 MINUTE POLYURETHANE WOOD ADHESIVE GEL GENERAL PURPOSE SILICONE HEAVY DUTY WONDER WIPES PINKGRIP

29 29 29 29

CONTENTS

Schönox® GmbH was purchased by Sika AG in late 2013, and is part of the extensive Sika group of companies. Schönox® products are distributed in more than 20 countries throughout Europe and North America from their Rosendahl site in Germany. All of the Schönox® products are developed and produced to the highest quality using state of the art manufacturing facilities; they also have extensive R&D capabilities and constantly work to ensure that innovation is always at the forefront of the products they bring to market. From January 2015 we are proud to announce that the Schönox® range is exclusively available through Everbuild – A Sika Company, with leading products ZM Rapid, iFloor System and LC Liquid and Powder available to order alongside the Sika and Everbuild branded products.

www.everbuild.co.uk

LEVELLING COMPOUNDS

Levelling compounds today are far more technically advanced than they have ever been. Schönox®, part of the Sika Group of companies are at the forefront of this development and bring to you not only products with exceptional smoothing and levelling properties but also fast drying, enabling further finishes to be applied in as little as two hours after application.

Ready, Set, Go ...

LEVELLING COMPOUNDS

SCHÖNOX® ZM RAPID – the levelling compound that lets you lay the floor after only 1 ½ hours. This rapid setting self-levelling compound enables installers to lay the floor coverings in as little as 90 minutes after screeding. Suitable for use with underfloor heating systems, SCHÖNOX® ZM RAPID is a good all-rounder, and an absolute must for any installer with a time critical job. Technical data Pot life (working time): Ready for foot traffic: Ready for covering: Working temperature: Coverage: Shelf Life:

approx. 20-30 minutes at +20 °C after approx. 1 to 1.5 hours up to 10mm thickness after approx. 1.5 to 2 hours for textile, vinyl coverings, LVT’s and linoleum. Up to 10mm thickness after approx. 12 hours for coverings sensitive to moisture (like parquet, cork, synthetic rubber) not below +5 °C, not above +30 °C 16m2 at 1mm (1.5 kg/m2/mm) 6 months

www.everbuild.co.uk

German Made for the British Trade

Schönox® LC Powder & Liquid High Performance two component latex levelling compound

Flooring Contractor: Rees Flooring Ltd Main Contractor: Kier Construction

A protein free, two-component self-levelling screed for interior use that can be laid at a thickness of 3-20mm without aggregates, and 10-30mm with aggregates. 4.5 litres of SCHÖNOX® LC LIQUID is applied to a 25kg bag of SCHÖNOX® LC POWDER to create a latex- & polymermodified levelling compound that is ideal for use below textile and other flexible floor coverings, as well as parquet flooring. It is ideal for use with underfloor heating systems, and can be used on concrete, rapidhardening cement systems, cement screeds, gypsum screeds, new mastic asphalts IC10/15 (layer thickness up to 5 mm), and also old substrates such as ceramic/terrazzo. Foot traffic can be accepted after approx. 3 hours. Floor coverings (up to 5mm thick) can be laid after 24hrs. Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode 5055492701299

SCHLCP25

Grey

25kg

single

40 pcs

SCHLCLQ4

White

4.5 Litre

24 boxes 4016447016647

Substrates: • concrete • rapid-hardening cement systems • cement screeds • gypsum screeds • new mastic asphalt • old substrates such as ceramic/terrazzo. Preparation: For full sub-floor preparation details please refer to current technical data sheet. Prime absorbent floor substrates with SCHÖNOX® VD (1:3). Prime non-absorbent floor substrates with SCHÖNOX® SHP or SCHÖNOX® VD® (1:1). Gypsum substrates should be protected against moisture with SCHÖNOX® VD (1:1) The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%.

Technical data Pot life (working time): Ready for foot traffic: Ready for covering: Working temperature: Coverage per unit: Compression strength: Shelf Life:

Mixing ratio: 4.5 litres of SCHÖNOX® LC LIQUID is applied to a 25kg bag of SCHÖNOX® LC POWDER In layer thickness of 10 – 30 mm the aggregate is added last. Bulking material: approx. 65 wt.%, corresponds to 16kg clean silica sand 0-3 mm grain size or clean 3mm granite chippings. Application: Fill a clean vessel with SCHÖNOX® LC LIQUID and add SCHÖNOX® LC POWDER. Mix to a homogenous consistency using a 600rpm mixer. Allow to stand for approx. 4 minutes, mix again thoroughly. Pour out the levelling compound and spread using a smoothing trowel or pin leveller. In higher-thicknesses use of a spike roller is recommended. Discard any stiffened material – do not add extra liquid.

approx. 30 minutes at +20°C after approx. 3 hours up to 5 mm layer thickness after approx. 24 hours not below +5°C, not above +30°C approx. 5-6 m2 at 3 mm 20 N/mm2 after 28 days 6 months

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

”The Schonox products used worked really well within the timescale set out by the main contractor. All in all very pleased.“ Bob Stones

LEVELLING COMPOUNDS

Uses: • for interior use • for use under textile and other flexible coverings • for use under parquet (layer thickness above 5mm)

New School Construction: The Orion Primary School, Edgware

Case Study

Orion Primary School Products used: Schönox® SDG Schönox® LC Powder & Liquid

Schönox® Emiclassic Schönox® PU900

Schönox® SHP

This primary school development, Led by Bob Stones, Contract Manager for Rees Flooring is a prime example of the Schönox® range in use.

sub-floor. Schönox® SDG is a rapid drying liquid DPM which can be used up to 90%RH after applying 2 coats. It requires no additional primer before screeding, and so was ideal for this project, as Rees Flooring was then able to damp-proof and screed all on the same day.

spread 2 inches either side, using a wire mesh for reinforcement. Schönox® SHP primer was then used on top to allow a good adhesion for the latex levelling compound to be used.

Using hygrometers, several moisture tests were undertaken to establish the moisture content of the sub-floor and whether a damp proof membrane would be required. Being a working construction with many different trades onsite, testing had to be undertaken over a 4 week period when rooms and corridors where floors were to be laid, were released. The readings were between 76%RH & 88%RH so Schönox® SDG DPM was advised for damp proofing the entire

Before the DPM was installed it was decided with help from the Schönox® technical team, to tackle the construction joints with a polyurethane (PU) adhesive system: Schönox® PU900. This allowed for a quick solution when time is critical, as is often the case on such installations. Schönox® PU 900 adhesive was poured into the joints and

As the subfloor on the first floor was very uneven, giving a wave like effect, an effective levelling compound laid up to at least 8mm was required. Schönox® LC was ideal as it can be used up to 20mm without bulking out. Schönox® LC levelling compound was used at between 8-10mm on the first floor, and on the ground floor at 5mm. Finally, Schönox® Emiclassic adhesive was used to bond all safety vinyl sheets.

www.everbuild.co.uk

Schönox® ZM Rapid

Schönox® FPL Plus

Rapid setting self-levelling compound with very low emissions, for internal applications.

A self levelling compound for use from 3-50mm, or 60mm with aggregate.

For layer thicknesses 1 to 10mm without aggregates and 5 to 25mm with added aggregates. Suitable for almost all internal substrates, SCHÖNOX® ZM RAPID allows coverings to be laid after approximately 90 minutes. With very low shrinkage and good absorptivity, SCHÖNOX® ZM RAPID is suitable for underfloor heating applications. It is also suitable for castor wheels loading with layer-thicknesses great than 1mm (according to EN 12 259).

Noted for its rapid hardening, high strength, and low shrinkage, SCHÖNOX® FPL PLUS can be used for both interior & exterior applications, as it is both frost resistant and waterproof. Suitable for use with underfloor heating systems, SCHÖNOX® FPL PLUS is both pourable and pumpable, and is ready for covering after approx. 4 hours, for ceramic tiles on concrete floors. It has low VOC emissions, and is regulated under EMICODE EC1 Plus. After adding 4.5 litres of water to 25 kg of powder, SCHÖNOX® FPL PLUS is ready to use.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHZMRAP25

Grey

25kg

single

4016447022914

SCHFPLPS25

Grey

25kg

single

4016447008369

Working temperature: Coverage: Reaction to fire: Shelf Life:

42 pcs

hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: For 25kg of SCHÖNOX® ZM RAPID approx. 5.75-6 litres of water In layer thickness of 5-15mm the aggregate is added last. Bulking material: approx. 50 wt.%, corresponds to 12.5kg Quartz Sand 0.20.8mm for 25kg SCHÖNOX® ZM RAPID. In layer thickness of 10-25mm the aggregate is added last. Bulking material: approx. 65 wt.%, corresponds to 16kg Quartz Sand 0.2-0.8mm for 25kg SCHÖNOX® ZM RAPID. Application: Using a clean vessel, add SCHÖNOX® ZM RAPID to clean water. Mix to a homogenous consistency using disc stirring rod. Allow to stand for approx. 3 minutes, mix again thoroughly. Pour out the levelling compound and spread using a smoothing trowel. In higherthicknesses contact with vertical structures should be avoided. If a second layer is to be applied, the first should be primed with SCHÖNOX® VD (1:1) when dry. Avoid contact to metals.

approx. 20-30 minutes at +20 °C after approx. 1 to 1.5 hours up to 10mm thickness after approx. 1½ to 2 hours for textile, vinyl coverings, LVT’s and linoleum. Up to 10mm thickness after approx. 12 hours for coverings sensitive to moisture (like parquet, cork, synthetic rubber) not below +5 °C, not above +30 °C 16m2 at 1mm (1.5 kg/m2/mm) A1fl-s1 with 20 °C and 65 % rel. humidity 6 months

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

Uses: • for interior & exterior use • for use on balconies and terraces • for use as a repairing mortar for filling holes In outdoor and wet areas SCHÖNOX® FPL PLUS must be protected by a SCHÖNOX® waterproofing membrane and tiles. Substrates: • Cement and rapid cement screeds • Calcium sulphate based screeds • Old substrates such as ceramic tiles, natural stones and terrazzo • Old and new mastic asphalt screeds (sanded) IC 10 and IC 15 according to EN 13 813 (please refer to data sheet) Preparation: For full sub-floor preparation details and details surrounding moisture content, please refer to technical data sheet. Prime absorbent substrates with SCHÖNOX® VD (1:3) Prime non-absorbent substrates with SCHÖNOX® SHP or SCHÖNOX® VD (1:1). Prime magnesia screeds with SCHÖNOX® SHP For exterior use and high layer thicknesses, prime with Sika® Primer MB to ensure the subfloor has an effective DPM.

Technical data Pot life (working time): Ready for foot traffic: Ready for covering:

Application temperature: Material consumption: Coverage: Reaction to fire: Shelf Life:

42 pcs

With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: For layer thicknesses of 3 to 50mm, mix SCHÖNOX® FPL PLUS with 4.5 litres of water Bulking material: approx. 65 wt.%, corresponds to 16kg of Quartz Sand 0.1-3mm for 25kg if required Application: In a clean vessel, add SCHÖNOX® FPL PLUS to the required amount of water. Mix to a homogenous consistency. Spread the product using a suitable tool and ventilate using a spike roller. If a second layer of levelling compound is to be applied, the first must be primed with SCHÖNOX® VD (1:1) when dry. The second layer should not exceed the thickness of the first.

LEVELLING COMPOUNDS

Uses: • for internal applications • for filling, smoothing and levelling of substrates • for full-surface levelling under wooden floors Substrates: For filling, smoothing and levelling of: • concrete • cement and rapid cement screeds • old substrates such as ceramic tiles, natural stones and terrazzo, or with old water-resistant adhesive residues. • calcium sulphate & magnesia based screed • new & old mastic asphalt screeds Preparation: For full sub-floor preparation details please refer to current technical data sheet. Prime absorbent floor substrates with SCHÖNOX® VD (1:3). Prime non-absorbent floor substrates with SCHÖNOX® SHP or SCHÖNOX® VD (neat). Prime calcium sulphate substrates with SCHÖNOX® VD (1:1 ) Prime magnesia screeds with SCHÖNOX® SHP For wooden substrates protect against moisture with SCHÖNOX® VD (neat / drying time 2hrs) The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated

Technical data Pot life (working time): Ready for foot traffic: Ready for covering:

German Made for the British Trade

approx. 40 minutes at +20 °C after approx. 4 hours up to 60mm after approx. 4 hours for ceramic coverings on concrete and cementious screeds. On other substrates longer drying times are required. not below +5 °C floor temperature approx. 1.8 kg/m2/mm approx. 5m2 at 3mm A1 / A1fl 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

www.everbuild.co.uk

SCHÖNOX® AP GYPSUM

Schönox® APF Gypsum

A synthetic gypsum self-levelling compound for use from 1 to 45 mm.

Synthetic gypsum fibre-reinforced, self-levelling compound for use from 3-15mm in internal areas.

Especially suitable on all gypsum substrates, as well as on cast asphalt screeds according to DIN 18 560, SCHÖNOX® AP can also be used on cement substrates in interior areas. Suitable for use with underfloor heating systems, and for castor wheel loading, SCHÖNOX® AP can be used in thicknesses of 1 to 30mm (without aggregate), or 10-45mm (when bulked out with silica sand/granite chippings). It boasts high strength values (40 Newton compressive strength), with low stress, while also being proteinfree, and low in emissions (EC1). Used in conjunction with SCHÖNOX® SHP primer SCHÖNOX® AP can be used to overlay old, firmly bonded, resilient floor coverings. After adding of 6.0 l of water to 25.0 kg of powder, SCHÖNOX® AP is ready to use.

SCHÖNOX® APF is especially suited for use with wooden floor boards, chipboard (V100), mastic asphalt screeds and other critical substrates in combination with elastic and textile coverings. Ready for foot traffic after approx. 3 hours, it has a particularly high coverage rate, as well as very low emissions. It boasts high flexural strength, and is particularly suited for use with underfloor heating systems. It provides a particularly low-pore and smooth surface which is ideal for use with soft floor coverings where every pit beneath is felt. SCHÖNOX® APF is ready to use with addition for 5.5 litres of water; can be poured or pumped.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHAPLEV25

Grey

25kg

single

4016447022198

SCHAPFLEV25

Grey

25kg

single

4016447017637

Compressive strength: EN13813: Shelf Life:

42 pcs

The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: Mix 6 litres of water with 25kg SCHÖNOX® AP. In layer thickness of 10 – 45 mm the aggregate is added last. Bulking material: approx. 65 wt.%, corresponds to 16kg of Quartz Sand 0.1-3mm for 25kg SCHÖNOX® AP Application: In a clean vessel, add SCHÖNOX® AP to the required amount of water. Mix to a homogenous consistency. Leave to stand and mix again. Pour out and spread using a smoothing trowel. If a second layer of levelling compound is to be applied, the first must be primed with SCHÖNOX® VD (1:1) when dry. The second layer should not exceed the thickness of the first.

approx. 30 minutes at 18 °C after approx. 2 hours - after approx. 24 hours. not below 5 °C floor temperature 25kg will cover approx. 5.5m2 at 3mm thickness (1.5 kg/m2/mm) 40N/mm2 after 28 days CA-C40-F10 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

Uses: • for internal applications • for filling, smoothing, and levelling of substrates Substrates: • chipboard (V100 according to DIN 68 771) • old substrates such as ceramic tiles • old, water-resistant adhesive residues • concrete • dry screeds • cement screeds • rapid cement screed systems • gypsum screeds • mastic asphalt screeds (IC 10 and IC 15 according to DIN 18 354 and DIN 18 560, layer thickness 3 – 8 mm). Preparation: For full sub-floor preparation details please refer to current technical data sheet. Prime absorbent floor substrates with SCHÖNOX® VD (1:3). Prime non-absorbent floor substrates with SCHÖNOX® SHP or SCHÖNOX® VD (neat). Prime calcium sulphate substrates with SCHÖNOX® VD (1:1) Prime magnesia screeds with SCHÖNOX® SHP Prime xyolite screeds with Sika® Primer MB For wooden substrates protect against moisture with SCHÖNOX® VD (neat / drying time 2hrs). The subfloor should have an effective damp proof membrane.

Technical data Pot life (working time): Ready for foot traffic: Ready for covering: Application temperature: Coverage: Compression strength: EN 13813 Shelf Life:

42 pcs

With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: For 25kg of SCHÖNOX® APF approx. 5.5litres of water Application: Using a clean vessel, add SCHÖNOX® APF to clean cold water. Mix to a homogenous consistency using a 600rpm mixer. Allow to stand for approx. 3 minutes, mix again thoroughly. Recommend full containers mixed to guarantee even distribution of the fibres. Pour out the levelling compound and spread using a smoothing trowel. In higherthicknesses a spike roller is recommended. If a second layer applied, prime first with SCHÖNOX® VD (1:1) when dry.

LEVELLING COMPOUNDS

Uses: • for interior use • for use under textile and elastic coverings, as well as parquet Substrates: • Calcium sulphate based screeds • New mastic asphalt screeds IC 10 and IC 15 according to EN 13 813, layer-thickness 1,0 to 8,0 mm. • Concrete • Dry screeds • Cement and rapid cement screeds • Magnesia screeds • Xylolite screeds • Old substrates such as ceramic tiles, natural stones and terrazzo • Old substrates with old water-resistant adhesive residues • Suitable particle board or OSB constructions, screwed concrete Preparation: For full sub-floor preparation details please refer to current technical data sheet. Prime absorbent floor substrates with SCHÖNOX® VD (1:3). Prime non-absorbent floor substrates with SCHÖNOX® SHP or SCHÖNOX® VD (neat). Calcium substrates should be primed with SCHÖNOX® VD (1:1) Gypsum substrates should be protected against moisture with SCHÖNOX® VD (1:1)

Technical data Pot life (working time): Ready for foot traffic: Ready for covering: Application temperature: Coverage:

German Made for the British Trade

approx. 30 minutes at +20 °C after approx. 3 hours up to 3mm thickness after approx. 24 hours (48hrs for parquet) not below +5 °C floor temperature 25 kg will cover approx. 5.5m2 at 3mm (1.5 kg/m2/mm ) 40 N/mm2 after 28 days CA-C40-F10 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

www.everbuild.co.uk

PRIMERS & DPMS

Whether you are priming an old cement based substrate without a damp proof membrane, a new anhydrite screed, keying old ceramic tiles or isolating adhesive residues, Schönox® has a top of the range product to ensure your requirements are met in full.

Building on a Strong Foundation

PRIMERS & DPMS

As part of the Sika Group Schönox® customers have access to an even wider range of products from both the Sika merchant range and the Everbuild range. This includes a wide range of primers, cleaners, adhesives and ancillary products. Combined, the three brands offer professionals a one-stop shop for all their needs.

www.everbuild.co.uk

Schönox® VD

Schönox® SHP

A general purpose primer for internal use with SCHÖNOX® levelling compounds.

A solvent-free, 1-component special acrylate dispersion primer for interior applications.

SCHÖNOX® VD is a synthetic resin dispersion primer, which is suitable for the pre-treatment of absorbent, non-absorbent and smooth substrates on both floors and walls. It is solvent free, with very low emissions. With excellent penetration and low consumption, it only requires a short waiting/drying time. SCHÖNOX® VD can be applied to almost all substrate types, improving grip, and binding any residual dust. It is ready to use neat, or can be diluted with water, and can be applied by spray, brush or roller.

SCHÖNOX® SHP is a special primer for sound, smooth and nonabsorbent substrates. Especially suitable for laying on old vinyl, linoleum and rubber coverings. With short waiting times, and easy roller application, this product provides optimum adhesion. It has low consumption/high coverage rates, and can be used on both floors and walls. It has low emissions, and is also odourless, making it pleasant to use.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

SCHVPPRIME1

Light blue

1kg

30 boxes 4016447011451

SCHVDPRIME10

Light blue

10kg

single

60 pcs

Working temperature: Storage temperature: Waiting times:

Shelf Life:

Pack Barcode 4016447011444

The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: On sound substrates, like cast asphalt, ceramic tiles, old water resistant adhesive residues, chipboard, wood substrates and others, apply SCHÖNOX® VD neat. On cement screeds, apply SCHÖNOX® VD mixed at a ratio of 1:3 with water. On gypsum substrates, apply SCHÖNOX® VD mixed at a ratio of 1:1 with water Application: Shake or stir well before use. Avoiding puddles, apply via roller, brush. Can also be sprayed (mixing ratio 1:1 or more). On very absorbent substrates a second coat is recommended. Use within 1 week any product mixed with water.

1kg/l (dependent on absorbency of substrate) neat – approx. 80g/m2 (12.5m2/kg) diluted 1:1 - approx. 70g/m2 (15m2/kg) diluted 1:3 - approx. 50g/m2 (20m2/kg) not below +5 °C not below +5 °C approx. 10 mins on cementitious substrates and with gypsum based SCHÖNOX® levelling compounds on gypsum substrates approx. 15 - 30 mins on non-absorbent and low absorbent substrates approx. 2 hours on wood substrates and chipboard approx. 24 hours with cement levelling compounds on gypsum substrates 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHSHPPRIME5

Blue

5kg

Single

4016447010454

Uses: • as a primer to improve adhesion on smooth and sound substrates • as a primer over Sika® Primer MB Substrates: • terrazzo, ceramic tiles, natural stone coverings • insufficiently sanded mastic asphalt screeds or rolled asphalt concrete • old sealed/coated surfaces • old tight and smooth concrete substrates • magnesia screeds • steel and other metals • fully bonded, thoroughly cleaned and sanded resilient floorings (except POcoverings) Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure smooth, sound, clean, dry and free from contaminants. The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%.

Technical data Density: Coverage: Application temperature: Temperature resistance: Drying times: Storage temperature: Shelf Life:

90 pcs

Mixing ratio: Apply undiluted. Application: Shake or stir well before use. Avoiding puddles, apply via roller, brush or pad applicator. Apply SCHONOX® levelling compounds after a drying time of approx. 1 to 2 hours (refer to relevant levelling compound data sheet). Consult data sheet for information surrounding application on old vinyl, lino, rubber coverings

PRIMERS & DPMS

Uses: • to reduce absorbency of cement screeds, concrete, rapid cement screeds • to improve adhesion of the levelling compounds • to reduce moisture ingress into substrate Substrates: • chipboard (V100 according to DIN 68 771) • wooden-cement-boards • old substrates such as ceramic tiles • old, water-resistant adhesive residues • concrete • dry screeds • cement screeds • magnesia screeds • rapid cement screed systems • gypsum screeds • mastic asphalt screeds (IC 10 and IC 15 according to DIN 18 354 and DIN 18 560, layer thickness 3–8 mm). Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure smooth, sound, clean, dry and free from contaminants.

Technical data Density: Coverage:

German Made for the British Trade

1.3kg/l approx. 100-150g/m2 (6.5 - 10m2/kg ) not below +15 °C up to 50 °C approx. 1-4 hours not below +5 °C 1 year

www.everbuild.co.uk

German Made for the British Trade

Schönox® SDG DPM Rapid drying, ready-mixed special dispersion based damp-proof membrane for interior use.

Schönox® has been a leading supplier to the German market for many years, delivering quality products manufactured using state of the art technology.

German Made for the British Trade

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHSDG10

Yellow

10kg

Single

4016447017798

Uses: • as a damp-proof membrane on moisture resistant substrates with increased residual moisture • under SCHÖNOX® floor levelling compounds with subsequent laying of textile and elastic coverings as well as parquet Substrates: • concrete • cement and rapid cement screeds Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure smooth, sound, clean, dry and free from contaminants. Basements should be sealed against rising damp. The subfloor should have an effective damp proof membrane. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%.

Technical data Density: Coverage/Consumption: Application & substrate temperature: Waiting time: Ready for foot traffic: Ready for floor levelling: Storage temperature: Shelf Life:

60 pcs

Mixing ratio: Apply undiluted. Application: Shake or stir well before use. Avoiding puddles, apply evenly using a long-pile roller (18mm). The 1st coat should fill pores. After 15 mins at 18°C floor temp. apply a 2nd coat at right angles to form a continuous film without pinholes. If a third coat is required, do not apply before 45 mins after the 2nd. Allow approx. 1 hour drying time after final coat applied. Check residual moisture content of screed before applying SCHONOX® levelling compounds (see data sheet for further details).

PRIMERS & DPMS

These products are now available to the British Trade through Everbuild – A Sika Company known for delivering innovation to the marketplace. This range is no exception.

SCHÖNOX® SDG is suitable for the fast pre-treatment of unheated cement based substrates with a residual moisture up to 90%RH as 2 coat application & 93%RH as a 3 coat application prior to applying SCHÖNOX® floor levelling compounds. It has good penetrability which means low product consumption (high coverage). The product is ready to use (one part), easy to apply and being solvent-free, with low emissions, is pleasant to use with low odour. It has short waiting times; just 15 minutes for the first coat, and approximately 45-90 minutes for the second coat, no priming or sanding is required prior to applying SCHÖNOX® levelling compounds.

1.2kg/l approx. 125-150g/m2 (per layer) (or 30-40 m² per 10kg unit for 2 coat system) not below +5 °C approx. 15 mins to apply 2nd coat approx. 45 mins (at 18°C floor temperature) approx. 1 hour (at 18°C or after adequate drying) not below +5 °C 1 year

www.everbuild.co.uk

Sika® Primer MB Primer and moisture control for use on difficult substrates prior to bonding floor coverings (soft and hard). Sika® Primer MB is a 2-component, solvent free, low viscosity, epoxy resin primer suitable for use in conjunction with all Schönox® adhesives and levelling compounds. It provides vapour control on damp cementitious substrates with a moisture content up to 6%CM. The product can also be used to provides substrate consolidation and adhesion promotion on weak or friable surfaces and is often used to isolate old adhesive residues prior to application of new finishes. The product is easy to apply and allows for fast track construction techniques. With good penetration and stabilisation of the substrate, Sika® Primer MB is suitable for refurbishing existing substrates against the egress of moisture which can damage floor finishes. Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SKPRIMEMB5

Blue

5kg

Single

45 pcs

7612894379990

SKPRIMEMB10

Blue

10kg

Single

30 pcs

7612894354652

PRIMERS & DPMS

Uses: Moisture control Substrate consolidation Adhesion promotion Adhesive residues isolation Substrates: • concrete • cement and rapid cement screeds • broadcast mastic asphalt • old adhesive residues Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure smooth, sound, clean, dry and free from contaminants. Old residues to be mechanically removed as thoroughly as possible. Basements should be sealed against rising damp. Gypsum screeds should have a reading of <0.5CM%. Mixing ratio: By weight: 3 parts (Part A): 1 part (Part B) By volume: 100 parts (Part A): 37 parts (Part B)

Technical data Density: Coverage/Consumption: Application & substrate temperature: Pot life: Ready for foot traffic: Ready for floor levelling: Curing speed: Storage temperature: Shelf Life:

Application: Add part B to part A in the correct ratio using an electric stirrer at a low speed (300-400 rpm). Mix for 3 minutes. Apply with medium pile roller. Refer to technical data sheet for number of coats depending on application. Leave a minimum 8 hours and maximum 36 hours between coats.

Schönox® has a full range of technically advanced dispersion adhesives to suit every application. From pressure sensitive to the unique roller applied iFloor system for installing luxury vinyl tiles and planks in a quarter of the time, Schönox® adhesives will provide the installer with greater flexibility in all aspects of their installation.

ADHESIVES

1.1kg/l mixed approx. 400-600g/m2 (concrete/cementitious screed) approx. 250-350g/m2 (broadcast mastic asphalt) not below +10 °C approx. 30 mins at 20 °C After 10-12 hours (at 20°C) Once cured (approx. 8-10 hours) approx. 12 hours (at 20 °C) not below +5 °C 2 years

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate

www.everbuild.co.uk

German Made for the British Trade

SCHÖNOX® iFLOOR® Dispersion based rollable adhesive for laying of all types of luxury vinyl tiling on levelled substrates by professional fitters. SCHÖNOX® iFloor is a revolutionary new system that incorporates a unique rollable adhesive that provides an extremely clean and fast installation. No excessive adhesive residues, and no residual adhesive moving up through the joints, leaves the vinyl surface clean, as well as the installer’s hands. By forming a flat adhesive bed instead of adhesive notches, this product will not cause point load deformation. As only a thin layer is required, it boasts particularly high coverage rates. It bonds the vinyl immediately, allowing for immediate foot traffic, and therefore a very fast installation.

SCHÖNOX® iFLOOR is a revolutionary new system that incorporates a unique rollable adhesive that provides an extremely clean and fast installation. Supplied in kit form, including SCHÖNOX® KH FIX Primer (and primer roller), plus iFLOOR adhesive (and adhesive roller), the system is extremely clean to use leaving no excessive adhesive residues. It has a long working time of 2 hours, but a short waiting time of just 10 minutes. It is ideal for repair work allowing for damaged tiles and planks to be easily lifted out and replaced. Technical data Coverage: Small kit – approx. 50m2 Large kit – approx. 125m2 Emicode: EC 1 PLUS: very low emissionPLUS Final Strength: after approx. 72 hrs Open Time: 2 hours Shelf life: 1 year Waiting time: 10-15mins

Colour

Pack Size

Box Qty

Pallet Qty

Pack Barcode

SCHIFLOOR50

Light Green

50m2

Single kit

24 pcs

4016447019846

SCHIFLOOR125

Light Green

125m2

Single kit

18 pcs

4016447019037

SCHÖNOX® iFloor is available in 2 sizes, in kit form, one for an area of 50m2, and another for an area of 125m2, so no complicated calculations are required to ensure the correct amount of product for the job. As well as the iFLOOR adhesive and adhesive roller, both kits are supplied with SCHÖNOX® KH FIX (and priming roller), for priming the substrate prior to applying the iFLOOR adhesive. KH FIX is a ready-mixed, rapid drying primer with very low emissions. It too has a very high coverage rate of 25m2/kg and is extremely easy to use. Both products can be used directly out of the tubs using the re-usable rollers provided. This system is also very easy to fix and repair. A damaged tile can be easily lifted out and replaced by another without any further surface preparation; just a small amount adhesive applied to the replacement tile. Uses: For bonding of luxury vinyl tiles in internal areas. Substrates: • suitable absorbent substrates in internal areas

Technical data Density: Coverage/Consumption: Application & substrate temperature: Open time: Waiting time: Final Strength: Storage temperature: Shelf Life:

Preparation: For full sub-floor preparation details please refer to current technical data sheet. Sound, even, absorbent surfaces achieved with SCHÖNOX® levelling compounds are advised. Prime with SCHÖNOX® KH FIX using the roller provided to bind dust and improve adhesion. Mixing ratio: No mixing required. Both the primer and adhesive are ready to use. Application: Stir the SCHÖNOX® iFLOOR® adhesive well. Apply evenly, avoiding puddles, using the SCHÖNOX® iFLOOR® ROLL. After approx. 10 minutes, lay tiles while still tacky. Rub down the covering, wait and rub again. Alternatively, put adhesive on the back of the covering as well as on the substrate and allow to dry until transparent. Connect the glued surfaces by pressing together. Laid areas are immediately ready to walk on. Replacement of single planks and resetting is normally possible without further sub-floor preparation.

ADHESIVES

Viva la Rollution!

Product Code

1kg/l adhesive : 80g/m2 (50m2 kit and 125m² kit); primer: 25m2/kg not below +15°C floor temp approx. 2 hours approx. 10-15 mins after approx. 72 hours not below +5°C 1 year

www.everbuild.co.uk

SCHÖNOX® EMICLASSIC

SCHÖNOX® UNITECH

Universal pressure sensitive dispersion adhesive for all flexible coverings including textile, linoleum, rubber & impact sound underlay in interior areas.

Solvent-free dispersion adhesive for bonding flexible coverings in interior areas.

SCHÖNOX® EMICLASSIC is suitable for both wet and pressure sensitive adhesion. It is solvent free with low odour & high coverage rates. SCHÖNOX® EMICLASSIC is also ideal for use with underfloor heating systems, or areas where castor wheels will be used. Working well over all SCHÖNOX® levelling compounds, this product is easily spread and has short waiting times; it rapidly develops a strong bonding strength. SCHÖNOX® EMICLASSIC is also particularly suited for use with difficult floor coverings. For a list of suitable flexible coverings and backing types, please see data sheet. Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHEMICLAS6

Beige

6kg

Single

90 pcs

4016447004491

SCHEMICLAS14

Beige

14kg

Single

44 pcs

4016447004255

Application temperature: Temperature resistance with UFH: Open time: Waiting time: Drying Time: Final Strength: Storage temperature: Shelf Life:

Preparation: For full sub-floor preparation details please refer to current technical data sheet. Sound, even, absorbent surfaces achieved with SCHÖNOX® levelling compounds are advised. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Always condition coverings at room temperature and lay flat. Mixing ratio: No mixing required. Application: Stir the SCHÖNOX® EMICLASSIC adhesive well. Apply evenly, avoiding lumps, using a notched trowel or roller. Refer to data sheet for recommended trowel sizes for covering type. Correct notching is determined by the backing of the covering. For full application/ installation guide please refer to the current technical data sheet.

SCHÖNOX® UNITECH is suitable for wet adhesion, has short waiting times, high coverage rates, strong stringiness & has a rapid development of adhesion strength. Suitable for use over all SCHÖNOX® levelling compunds, this product is suitable for use with underfloor heating systems, and can be used in areas subjected to castor wheel loading.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHUNIMPAD14

Beige

14kg

Single

4016447018627

Uses: For bonding of : • PVC floor coverings • CV floor coverings • textile wall and floor coverings • Single or multi-layer needlefelt • Natural fibre coverings • linoleum sheet coverings Substrates: Substrates should have adequate strength, load bearing capacity, permanent dryness & be free of residues which may reduce adhesion. Substrates: • suitable substrates in interior areas • old coverings (PVC, CV, rubber, wood if sound Preparation: For full sub-floor preparation details please refer to current technical data sheet. Sound, even, absorbent surfaces achieved with SCHÖNOX® levelling compounds are advised. With subsequent laying of floor coverings, where moisture readings are above 75%RH, as tested with a properly calibrated hygrometer, then application of SCHÖNOX® SDG or Sika® Primer MB may

1.10kg/l By Roller: approx. 200g/m² (5m²/kg) By notched trowel A1-A4 200-300g/m² (3.33-5 m² per kg) By notched trowel B1-B4 300-500g/m² (2 - 3.33m² per kg) not below +15°C floor temp. up to +50°C

Technical data Density: Coverage/Consumption:

approx. 20-60 mins approx. 10-60 mins approx. 24 hours after approx. 72 hours not below +5°C 1 year

Application temperature: Waiting time: Drying Time: Final Strength: Storage temperature: Shelf Life:

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

44 pcs

be used to suppress residual moisture (see data sheet). Gypsum screeds should have a reading of <0.5CM%. Always condition coverings at room temperature and lay flat. Mixing ratio: No mixing required. Application: Stir the SCHÖNOX® UNITECH adhesive well. Spread evenly using a notched trowel. See data sheet for recommended trowel sizes. Non diffusion permeable coverings should be laid on absorbent substrates during the semiwet phase. Textile and lino coverings should be laid during the wet phase. Linoleum and diffusion permeable coverings should be laid on absorbent substrates while still wet.

ADHESIVES

Uses: For bonding of : • Textile wall and floor coverings • Woven fabrics • Single or multi-layer needlefelt • Natural fibre coverings • PVC and CV wall and floor coverings • Luxury vinyl tiles (LVT) • Impact sound insulation underlays • Linoleum coverings in sheets • Cork linoleum • Corkment • Synthetic rubber coverings with smooth & sanded backing • Synthetic rubber coverings with elastic foam underlay Substrates: • suitable substrates in interior areas • old coverings (PVC, CV, rubber, wood) if sound

Technical data Density: Coverage/Consumption:

German Made for the British Trade

1.39kg/l Trowel size A1-A2 - 300-350g/m² Trowel size B1-B2 400-500g/m² not below +15°C floor temp. approx. 5-10 mins approx. 24 hours after approx. 72 hours not below +5°C 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

www.everbuild.co.uk

SCHÖNOX® PU 900

SCHÖNOX® MULTI OBJEKT

Solvent-free 2-component polyurethane adhesive for bonding elastic coverings in interior areas or sheltered exterior areas.

Multi purpose dispersion adhesive for bonding almost all soft floor coverings in internal areas.

SCHÖNOX® PU 900 is especially suited for bonding PVC and rubber coverings, as well as a variety of other materials. This adhesive can be used on either absorbent or non-absorbent substrates. PU 900 is easily spread, can be used with underfloor heating systems, as well as in areas expecting castor wheel loading. Being solvent-free, and therefore possessing low odour, the product is pleasant to use. A long open time makes it easy to work with. It hardens quickly and reaches a high bonding strength.

SCHÖNOX® MULTI OBJEKT is a very low emission Multifunction dispersion adhesive. It is suitable for wet adhesion giving strong stringiness, short waiting times, high coverage rates and a rapid development of adhesion strength. It has low odour, is easy to apply and suitable for application on subfloor heating systems and caster wheel loading.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHPU9007

Beige

7.05KG (A:6kg; B:1.05kg)

Single

4016447012458

60 pcs

Mixing Ratio: Mix all Part B to all Part A (approx. 1:6 ratio) Application: Wearing gloves and protective goggles, add the hardener (Component B) to the resin (Component A) and mix to a homogenous consistency. Spread SCHÖNOX® PU 900 evenly using a notched trowel (size A2, B1, or B2). Lay the covering in the fresh adhesive bed. Roll immediately and again after 1-2 hours. For filling or sealing cracks, cover the fresh adhesive with Quartz sand (0.2-0.8mm) to ensure a safe adhesion with subsequent materials. Clean tools immediately after use.

1.5kg/l approx. 500-1000g/m2 (7-14 m² per 14kg unit) till 50°C not below +15°C floor temp. approx. 40 min at 18°C none approx. 24 hours after approx. 72 hours not below 0°C 6 months

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHMULTI14

Beige

14kg

Single

4016447018115

Uses: For bonding of : • Textile coverings (check data sheet for suitable backings) • Woven fabrics • Single or multi-layer needlefelt • natural fibre coverings • PVC and CV coverings • Lino sheet coverings • Cork linoleum • Corkment Substrates: Absorbent and non-absorbent substrates, interior living and business areas Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure free from dust, dirt, oil, grease, loose particles, and old adhesive residues. Sound, even, absorbent surfaces achieved with SCHÖNOX® levelling compounds are advised. Always condition coverings at room temperature and lay flat.

Technical data Density: Coverage/Consumption: Application temperature: Waiting time: Open Time: Drying Time: Final Strength: Storage temperature: Shelf Life:

44 pcs

Mixing ratio: No mixing required. Application: Spread the adhesive evenly, avoiding lumps, on the substrate with a notched trowel. Refer to technical data sheet for recommended trowel sizes for the type of coverings being laid. The right amount of adhesive required is determined by the type of backing on the covering. Ensure a gap is left between linoleum sheets. Rub down or roll the covering once, and then again after a short wait. Leave for at least 24 hours before sealing the joints. For full application instructions please refer to technical data sheet.

ADHESIVES

Uses: For bonding of : • PVC coverings • Synthetic rubber coverings • Lino coverings • Rubber granulate underlays • Grass carpets As a repairing compound for cracks in screeds. Substrates: Absorbent and non-absorbent substrates in interior or covered exterior areas. Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure free from dust, dirt, oil, grease, loose particles, and old adhesive residues. Sufficient adhesion on levelled substrates is achieved by using highly quality levelling compounds (layer thickness ≥ 2 mm), such as SCHÖNOX® ZM Rapid or SCHÖNOX® APF. Some uneveness in the substrate can be levelled out with SCHÖNOX® PU 900. Always condition coverings at room temperature and lay flat.

Technical data Density: Coverage/Consumption: Temperature resistance: Application temperature: Pot life: Waiting time: Drying Time: Final Strength: Storage temperature: Shelf Life:

German Made for the British Trade

1.3kg/l Trowel (Size A1-A2): approx. 280-350g/m² Trowel (Size B1-B2): approx. 370-500g/m² not below +15°C floor temp. approx. 5-15 mins approx. 15-30 mins approx. 24 hours after approx. 72 hours not below +5°C 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

www.everbuild.co.uk

SCHÖNOX® DUROCOLL

SCHÖNOX® TACKIFIER

Multi purpose dispersion adhesive for bonding all types of soft floor coverings in internal areas.

Roller applied anti-slip tackifier for fixing all types of carpet tiles.

SCHÖNOX® DUROCOLL is an adhesive ideally suited for use with problematic, high movement soft floor coverings. This high quality, fibre reinforced adhesive is appropriate for use with underfloor heating systems, and has a low consumption with high coverage. It is easy to apply and rapidly builds to a very high final strength. This product compensates for the higher plasticity of some imported vinyl products.

Used internally, this product is easily applied by roller to fix all types of carpet tiles to most substrates. It has low consumption and high coverage rates. By remaining wet (tacky) for a very long period, the product holds carpet tiles in place, but also allows for the easy replacement of tiles when required. The product is suitable for use with underfloor heating systems and in areas where castor load bearing is expected.

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

SCHDURO14

White

14KG

Single

4016447013608

SCHTACKI10

White

10kg

Single

4016447018498

Application temperature: Waiting time: Open Time: Drying Time: Final Strength: Storage temperature: Shelf Life:

44 pcs

Mixing Ratio: No mixing required. Application: Spread the adhesive evenly, avoiding lumps, on the substrate with a notched trowel. Refer to technical data sheet for recommended trowel size for type of coverings being used. The right amount of adhesive required is determined by the type of backing on the covering. Rub down or roll the covering once, and then again after a short wait. Leave for at least 24 hours before sealing the joints. For full application instructions please refer to technical data sheet.

1.35kg/l Trowel (Size A1-A2): approx. 250-300g/m² Trowel (Size B1-B2): approx. 350-450g/m² not below +15°C floor temp. approx. 5-20 mins approx. 20-30 mins approx. 24 hours after approx. 72 hours not below +5°C 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

Uses: For fixing: • Textile tiles without surface tension • Conductive and antistatic textile carpet tiles • Loose laid textile sheet coverings Substrates: Sound internal substrates Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure free from dust, dirt, oil, grease, loose particles, and old adhesive residues. Always condition coverings at room temperature and lay flat. Mixing ratio: Generally applied undiluted, but level of diluted can be adjusted to suit the covering.

Technical data Density: Coverage/Consumption: Application temperature: Waiting time: Open Time: Final Strength: Storage temperature: Shelf Life:

90 pcs

Application: Spread the tackifier evenly with a foam roller, avoiding lumps. Ensure enough product is used for sufficient bonding. Coverings with smooth backings, and carpet tiles are usually laid when the adhesive film is transparent but still tacky. Coverings can be removed by slowly peeling away from the substrate. Refer to technical data sheet and covering manufacturer’s instructions for full application instructions. Clean tools immediately after use with Heavy Duty Wonder Wipes.

ADHESIVES

Uses: For bonding: • Luxury vinyl tiles (LVT) • PVC and CV coverings • Textile coverings • Single multi-layer needlefelt Substrates: Suitable internal substrates Preparation: For full sub-floor preparation details please refer to current technical data sheet. Ensure free from dust, dirt, oil, grease, loose particles, and old adhesive residues. Sound, even, absorbent surfaces are achieved with SCHÖNOX® levelling compounds as advised. Always condition coverings at room temperature and lay flat.

Technical data Density: Coverage/Consumption:

German Made for the British Trade

1.03g/l approx. 75-120g/m² not below +15°C floor temp. approx. 30 mins up to 24 hours after approx. 72 hours not below +5°C 1 year

All values are approximate, are subject to local climatic fluctuations and vary according to the absorbency of the substrate.

German Made for the British Trade

Any good installer would be wise to have a quality grab adhesive, general purpose silicone sealant, a quick drying wood adhesive and some wipes in his armoury making him ready to face any challenge in front of him. As UK’s largest manufacturer of sealants and adhesives, Everbuild Building Products (a Sika Company) can provide these key products and many more besides.

PINKGRIP

General Purpose Silicone

Pinkgrip will stick just about anything on a building site that needs sticking.

General Purpose Silicone is a mid modulus silicone sealant that adheres to most smooth and nonporous materials.

Its amazing grabbing strength not only removes the need to pin under the workpiece to prevent slumping, but its revolutionary initial

Contains an anti-fungal compound to prevent mould growth in areas of high humidity. Forms a permanently flexible rubber seal.

‘Direct Bond’ eliminates the need for double stick methods.

Colour

Pack Size

Box Qty Pallet Qty Pack Barcode

PINKGRIP

Pink

350ml

105 boxes 5029347601690

Colour

Pack Size

Box Qty Pallet Qty Pack Barcode

GPSBK

Black

64 boxes

5029347600938

GPSBN

Brown

64 boxes

5029347200008

GPSGY

Grey

64 boxes

5029347608965

GPSTR

Clear

64 boxes

5029347100001 5029347000004

GPSWE

White

64 boxes

12GPSBK

Black

140 boxes 5029347600938

12GPSBN

Brown

140 boxes 5029347200008

12GPSGY

Grey

140 boxes 5029347608965

12GPSTR

Clear

140 boxes 5029347100001

12GPSWE

White

140 boxes 5029347000004

5 Minute Polyurethane Wood Adhesive Gel

HEAVY DUTY Wonder Wipes

Lumberjack 5 Minute Polyurethane Wood Adhesive Gel is a thixotropic, transparent, gap filling gel which sets hard in just 5 minutes.

Heavy Duty Wonder Wipes are textured wipes which are specially formulated for the building, engineering and allied trades to clean ingrained dirt from hands, tools and surfaces.

Particularly suitable for equipment manufacture and production line applications where rapid handling is required. Conforms to EN 204.

Contain a powerful Anti-Bacterial Additive that is tested by an independent laboratory to BSEN 1276:2009 and PREN 12054:1995 – the standards for killing bacteria on dirty surfaces and hands. Wonder Wipes are active against most common bacteria found in the home and workplace. See independent test results for details.

D4 Strength.

Product Code

ANCILLARIES

Product Code

Colour

Pack Size

Box Qty Pallet Qty Pack Barcode

Product Code

Colour

Pack Size

Box Qty Pallet Qty

Pack Barcode

5MINPU3

Trans

310ml

WIPEHD75

75 Wipes

5029347609467

100 boxes 5029347809034

www.everbuild.co.uk

INDEX

NOTES

SCHÖNOX® LC POWDER & LIQUID

GENERAL PURPOSE SILICONE

H HEAVY DUTY WONDER WIPES

P 29

PINKGRIP

SCHÖNOX MULTI OBJEKT

SCHÖNOX® PU 900

SCHÖNOX® SDG DPM

SCHÖNOX SHP

SCHÖNOX® TACKIFIER

SCHÖNOX UNITECH

SCHÖNOX® AP GYPSUM

SCHÖNOX® VD

SCHÖNOX APF GYPSUM

SCHÖNOX ZM RAPID

SCHÖNOX® DUROCOLL

SIKA® PRIMER MB

SCHÖNOX® EMICLASSIC

SCHÖNOX® FPL PLUS

SCHÖNOX IFLOOR

5 MINUTE POLYURETHANE WOOD ADHESIVE GEL

8 18

NOTES

INDEX & INFO SYMBOLS 30

INFO SYMBOLS

German Made for the British Trade

EMICODE EC 1R: very low emision, regulated

Resistant to high mechanical load

Suitable for castor wheel loading according to DIN EN 12 529

EMICODE EC 1: very low emision

Suitable for use with under floor heating

Blue Angel accreditation

CE Marked

Roller

GISCODE: RE 1 – epoxy resin adhesives and primers, solvent free, sensitising

Interior & exterior floor

Pumpable

Water-resistant

Interior floor & wall Exterior floor & Wall

Dust reduced

Mark of Conformity

Interior floor & wall

Rapid-drying

Wheelmark

Interior floor

GISCODE: D1 – Solvent free dispersion adhesives / primer

GISCODE: RU 1 – Polyurethane adhesive solvent free

DIN-norm

Smoothing trowel

Notched trowel

2 components

GISCODE: ZP 1 - cement-based products, low in chromat

Everbuild Building Products Ltd - A Sika Company Site 41, Knowsthorpe Way, Cross Green Industrial Estate, Leeds LS9 0SW Tel: 0113 240 3456 Fax: 0113 240 0024 Website: www.everbuild.co.uk Sika Ireland Limited Sika House, Ballymun Industrial Estate Dublin 11, Ireland Tel: 01 862 0709 Fax: 01 862 0707