september11

Page 1

SEPTEMBER 2011

4401-0110

4401-0111

ROKKER™ SERIES 4-CHANNEL FAIRING SPEAKER AMPLIFIER

4401-0110

•The world’s most powerful 4-channel speaker amplifier for your Harley® Bagger audio system •Full-range Class G amplifier features 125W RMS per channel X4 channels (500W total) driven continuous into a 2 ohm load at 14.4vdc and 70watts RMS continuous X4 channels into a 4 ohm load •Amplifier mounts to the top of the custom-made stainless steel bracket system, which has the slots in the bottom section to properly relocate two of the Harley CB, MP3 or XM sat radio modules (if installed) •Kit includes custom-made plug-n-play wiring harnesses with top-quality heavy gauge power/ground wires to be used in conjunction with the fused battery connection •Also includes all necessary mounting hardware and complete installation/operation instructions •Amplifier measures 105/8” L x 5” W (at widest point) x 15/8” T

PART #

DESCRIPTION

4401-0110

For 11 FLTRU

SUG. RETAIL $739.95

PART #

DESCRIPTION

SUG. RETAIL

4401-0111

For 06-11 FLHX

$739.95

4401-0111

PART #

DESCRIPTION

4401-0112

For 06-11 FLTR/FLTRX

SUG. RETAIL $739.95

71/4” ROKKER™ SERIES FAIRING LOWERS SPEAKER KIT

•Largest diameter round speakers that can be installed into the Harley® lower fairing shells with cone volume and mass comparable to a 6” x 9” speaker •High-power 3-way ROKKER series speaker set has been designed specifically for the Harley StreetGlide, Ultra, or RoadGlide custom with the factory Harley lower faring shells installed •2 ohms impedance and 170+ watts max power for the ultimate in raw audio power •Waterproof injection-molded polycarbonate woofer cone •High-flux strength but lite-weight dual-donut Neodymium magnet •High-efficiency vented voice-coil for improved cooling when operating at high volume levels for extended periods •Custom designed grillwork with high-output titanium-colored tweeter and mid-range drivers •Specially-tuned speaker-mounted passive crossover network for improved fidelity and frequency response •Top-quality lower fairing housing inserts molded specifically to fit the Harley lower fairing shells, to hold the J&M ROKKER series 71/4” speaker and custom grille with mounted high-output tweeter and mid-range •High-impact quality molded speaker inserts are textured in a matte finish and can be painted to match the color of your Bagger •Will perform extremely well when used with a medium to high-powered accessory amplifier

PART #

DESCRIPTION

4405-0241

For 06-11 FLHX, FLHTC, FLHTCU, FLHR w/ the factory Harley fairing lowers

SUG. RETAIL $449.95


AKRAPOVIC

A combination of the finest materials, state-of-the-art facilities and a hands-on approach by modern craftsmen with a passion for perfection come together in exhausts that are second-to-none in the world today. Akrapovic is the pinnacle of WORLD CLASS exhaust function and style. These striking exhausts are designed to provide riders with the ultimate level of performance that Akropovic calls “PURE POWER.” Here a combination of premium materials along with rigorous research and testing leads to the optimum exhaust flow for American V-Twins in a Euro-influenced style that is second to none. Akropovic exhausts also sound like no others. Just the right notes at the right times. Deep, resonant sound – the sound of Pure Power. And, sound that can be easily adjusted with optional components, including a Valve System for the Slip-On Mufflers that lets riders change the sound level with a simple switch – even on the fly. State-of-the-art facilities along with the highest levels of technology, materials, R&D and testing come together with passion and expertise to bring H-D owners a true World Class exhaust.

1800-1325

1800-1326

OPEN LINE 2-INTO-1 SYSTEMS

•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic all come together in these 2-into-1 systems •Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating or Silicone-based black powder coating •Systems feature Akrapovic’s in-house designed and tested, highDESCRIPTION performance silencer insert design for incredible power and famous sound PART # FOR 06-11 FXST/FLST, 06-11 FLHT/FLHX/FLHR/FLTR MODELS – not old-school baffling 1800-1325 Chrome •Systems include header, removable silencer insert, heat shields and 1800-1326 Black complete installation instructions

SUG. RETAIL $799.95 799.95

1800-1327 1800-1329

OPEN LINE 2-INTO-2 SYSTEMS

•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic all come together here in these 2-into-2 systems •Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating or Silicone-based black powder coating •Systems feature Akrapovic’s in-house designed and tested, high-performance silencer insert design for incredible power and famous sound – not old-school baffling •Systems include removable silencer inserts, heat shields and complete installation instructions

PART # DESCRIPTION FOR 06-11 FXD/FXDWG MODELS 1800-1327

2

Chrome

SUG. RETAIL $799.95

PART # DESCRIPTION FOR 06-11 XL MODELS 1800-1328

Chrome

SUG. RETAIL $749.95

PART # DESCRIPTION FOR 06-11 XL MODELS (CONT) 1800-1329

Black

SUG. RETAIL $749.95


1801-0531

1801-0534

1801-0530 1801-0535

1801-0529

SLIP-ON MUFFLERS

•Just like the full systems, these are loaded with an exceptional array of Akropovic features •Un-matched European craftsmanship, outstanding performance, design, and of 1801-0533 course the unmistakable deep resonant sound of Akrapovic; here with an Optional Sound Valve System that can even be adjusted on-the-fly •Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating and Silicone-based black powder coating as listed •Optional Sound Valve Systems are available separately •Dresser muffler bodies with end cap measure 20” L (29” overall length with subheader pipe installed) and are 41/2” W x 31/2” T at polygonal exit that tapers to 31/2” round inlet end •Includes mufflers, subheaders with heat shields, clamps and complete installation instructions •Sold in pairs

PART # DESCRIPTION FOR 07-11 FLSTF/FLSTFB, 07 FXSTD MODELS

SUG. RETAIL

1801-0534

Chrome

$1,149.95

1801-0535

Chrome

1,149.95

1801-0531

Chrome

1,049.95

1801-0530

Chrome

1,049.95

FOR 07-10 FXST/B/C, 07-11 FLSTC, 08-11 FXCW/C MODELS FOR 06-11 FXD/FXDWG MODELS (EXCEPT 08-11 FXDF, 10-11 FXDWG) FOR 06-11 FXDF/10-11FXDWG MODELS

PART # DESCRIPTION SUG. RETAIL FOR 06-11 FLHT/FLHX/FLHR/FLTR MODELS (EXCEPT 10 FLHX/FLTRX) 1801-0528 1801-0529

Chrome w/ chrome tips Chrome w/ black tips

1801-0532 1801-0533

Chrome Black

FOR 06-11 XL MODELS

$1,149.95 1,149.95 1,049.95 1,049.95

1861-0733 1861-0729

OPTIONAL SOUND VALVE SYSTEMS FOR SLIP-ON MUFFLERS

1861-0730

•The perfect complement to Akropovic’s SlipOn Muffler line allows riders to easily adjust for the sound level they want without ever leaving the bike, or getting their hands dirty •World Class design and function uses investment cast stainless steel housings and high-temperature graphite bearings throughout •Valve systems are cable-actuated through a hand control that is mounted on-bike where owner can reach it •At every setting there is still the unmistakable, deeply resonant sound of Akrapovic •Sold in pairs

PART #

DESCRIPTION

1861-0733 1861-0734 1861-0735 1861-0736 1861-0737 1861-0738

For For For For For For

mufflers mufflers mufflers mufflers mufflers mufflers

PART PART PART PART PART PART

SUG. RETAIL #s 1801-0528, 1801-0529 #1801-0530 #1801-0531 #s 1801-0532, 1801-0533 #1801-0534 #1801-0535

$449.95 449.95 449.95 449.95 449.95 449.95

HIGH-TEMPERATURE EXHAUST WRAP KITS

•Wraps will increase power and reduce radiated exhaust heat •Kits includes 50-ft., 1-in. wide top-quality high-temperature wrap and four stainless-steel tie wraps for that finishing touch •Wraps can withstand up to 2,000° •Available in black or tan •Replacement 4-pack exhaust wrap clamps are also available (PART #1861-0320)

PART #

DESCRIPTION

1861-0729 1861-0730

Black 1” x 50’ Tan 1” x 50’

SUG. RETAIL $64.95 59.95

3


BASSANI XHAUST

Look. You don’t just have to take Darryl Bassani’s word on it that his exhausts make more power than anyone else’s – check it out for yourself. Pick-up any bike (or car) magazine with Bassani included in an exhaust comparo-test and see who comes out on top! Because whether it’s Detroit’s latest road burner or Milwaukee Iron’s finest, Bassani Xhaust’s winning performance sends the competition packing. Check out “The Sound of Power” today.

ROAD RAGE II MEGA POWER SYSTEMS

•Designed specifically to address the needs of tuned motors built for high horsepower applications •Features 2-into-1 equal-length 13/4”-17/8” stepped headpipes •Megaphone muffler housing with 4” polished or black billet end cap with contrasting machined flutes •Include full-coverage heat shields •Includes O2 sensor bung PART # DESCRIPTION SUG. RETAIL plugs for non-sensor FOR 07-11 V-ROD MODELS applications Chrome, long meg w/ heat shields $699.95 •Include removeable baffle 1800-1317 1800-1318 Black, short w/ heat shields 739.95 •Made in the U.S.A.

1800-1318

ROAD RAGE II B1 POWER SYSTEMS

•Designed specifically to address the needs of tuned motors built for high horsepower applications •Uses a unique extended inner collector maximizing performance •Features 2-into-1 equal-length stepped headpipes; systems for Dyna feature 2-step headers, 13/4” to 13/8”; systems for V-Rod feature 3-step headers, 13/4” to 17/8” to 2” •4” straight-style performance muffler body with 21/2” x 161/2” baffle and billet end cap with contrasting machined flutes •Include full-coverage heat shields •Oxygen sensor port plugs also included for non-sensor applications •Made in the U.S.A.

PART # DESCRIPTION FOR 07-11 VRSCAW, VRSCDX, VRSCX, 09-11 VRSCF 1800-1315

Clean Cut Contrast Cut

SUG. RETAIL

Chrome w/ black billet end cap w/ machined contrasting and chrome heat shields

Clean Cut Chrome

1800-1315

1800-1316 $699.95

Sweep Contrast Cut

Slash Contrast Cut

Slash Chrome

1800-1316

PART # DESCRIPTION FOR 07-11 VRSCAW, VRSCDX, VRSCX, 09-11 VRSCF (CONT)

Sweep Chrome

SUG. RETAIL

Black w/ black billet end cap w/ machined contrasting and black heat shields

$739.95

Tech 10 Contrast Cut Tech 10 Chrome

ELITE EXHAUST END CAPS

•CNC machined billet aluminum construction •Available in chrome and Contrast Cut™ •Contrast Cut™ starts with a polished end cap that has been black anodized then re-cut to open up the design •Sold each •Made in the U.S.A.

PART # DESCRIPTION FOR VANCE & HINES 3.5” MUFFLERS 1802-0183 1802-0184 1802-0185 1802-0186 1802-0187 1802-0188

4

Clean Cut, Contrast Cut™ Clean Cut, chrome Slash, Contrast Cut™ Slash, chrome Sweep, Contrast Cut™ Sweep, chrome

SUG. RETAIL $99.95 99.95 99.95 99.95 99.95 99.95

SUG. PART # DESCRIPTION RETAIL FOR VANCE & HINES 3.5” MUFFLERS (CONT) 1802-0189 1802-0190

Tech 10, Contrast Cut™ Tech 10, chrome

1802-0191 1802-0192 1802-0193

Clean Cut, Contrast Cut™ Clean Cut, chrome Slash, Contrast Cut™

FOR VANCE & HINES 4” MUFFLERS

$99.95 99.95 99.95 99.95 99.95

1802-0195

PART # DESCRIPTION FOR VANCE & HINES 4” MUFFLERS (CONT) 1802-0194 1802-0195 1802-0196 1802-0197 1802-0198

Slash, chrome Sweep, Contrast Cut™ Sweep, chrome Tech 10, Contrast Cut™ Tech 10, chrome

SUG. RETAIL $99.95 99.95 99.95 99.95 99.95


PREDATOR 2-UP SEATS

0801-0615

•Solar-reflective leather in the seating area and automotive-grade vinyl on 0801-0614 the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl •Molded polyurethane foam for maximum comfort and styling •3/16” ABS thermoformed seat base for a perfect fit •Rubber bumpers and fully carpeted bottom to protect paint •Fit with all Drag and most H-D sissy bars •1” lower than stock (unless noted) PART # DESCRIPTION •Include all mounting hardware FOR 94-96 FLHR MODELS (31” L X 101/2” W) •Made in the U.S.A. Smooth NOTE: 94-96 FLHR seats will fit also fit 89-93 FLHT models if hand rail is 0801-0614 0801-0615 Flame stitch removed and a lower dash extension PART #2202-0070 is used.

SUG. RETAIL $309.95 319.95

PREDATOR 2-UP SEATS

•Solar-reflective leather in the seating area and automotive-grade vinyl on 0802-0624 the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl •Molded polyurethane foam for maximum comfort and styling •3/16” ABS thermoformed seat base for a perfect fit •Rubber bumpers and fully carpeted bottom to protect paint PART # DESCRIPTION •Fit with all Drag and most H-D sissy bars FOR 84-99 FXST, FLST MODELS (29” L X 101/2” W FRONT X 63/4” W REAR) •Include all mounting hardware 0802-0624 Smooth •Lower rider 3/4” compared to stock seat unless noted 0802-0625 Flame stitch •Made in the U.S.A. 0802-0623

0802-0620

SOLO SEATS WITH BACKREST CAPABILITY

0822-0135

0802-0625

SUG. RETAIL $304.95 309.95 0822-0133

•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 0802-0619 25°F for a cooler seat, higher durability and longer life over conventional 0802-0618 leather or vinyl •Flexible urethane foam for maximum comfort •3/16” ABS thermoformed seat base with carpeted bottom and rubber bumpers to protect paint •Lower rider 11/2” from stock seat •Include two polished stainless steel mounting nuts and a leather fender bib for a cleaner installation •Optional EZ GLIDE I™ backrest (PART #0822-0135) features a detent bar with multiple detents on lower portion for adjustability up and down within the seat and chrome plated hardware that allows up to 2” of forward-rearward adjustment •Optional EZ GLIDE II™ backrest (PART #0822-0133) features multiple detents (with virtually no metal-to-metal contact) for vertical pad adjustment plus fore/aft adjuster •Both backrests will work in either position •Optional Solo Rear Seat/pillion seat are also available in matching styles and two sizes •Made in the U.S.A.

PART # DESCRIPTION FOR 84-99 FXST, FLST MODELS (18” L X 11” W)

0802-0618 0802-0619

SUG. RETAIL

Smooth Flame stitch

OPTIONAL SOLO REAR SEAT/PILLION PADS

0802-0620 0802-0621 0802-0622 0802-0623

Narrow smooth (11” L X 71/2” W) Narrow flame stitch (11” L X 71/2” W) Wide smooth (11” L X 9” W) Wide flame stitch (11” L X 9” W)

PREDATOR SEATS

$299.95 309.95

0822-0133 0822-0135

154.95 159.95 189.95 194.95

•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl •Custom-molded polyurethane foam for maximum comfort and styling •3/16” ABS thermoformed seat base for a perfect fit •Rubber bumpers and fully carpeted bottom to protect paint •Fit all Drag and most H-D sissy bars •11/2” lower than stock (unless noted) •Include all mounting hardware •Made in the U.S.A. NOTE: Will also fit 89-93 FLHT models when used with lower dash extension PART #2202-0070.

PART # DESCRIPTION OPTIONAL BACKRESTS

EZ GLIDE II backrest, solar-reflective leather, smooth (9” W x 51/4” H) EZ GLIDE I backrest w/ pouch, solar-reflective leather (10” W x 71/2” H)

0801-0616

$179.95 199.95

0801-0617

PART # DESCRIPTION FOR 94-96 FLHR MODELS

0801-0616 0801-0617

SUG. RETAIL

Smooth Flame stitch

SUG. RETAIL $289.95 299.95

5


LINDBY CUSTOM

Riders continue to ask for Lindby Custom products by name because they know that Per Lindby, wife Anne and their team are the leaders in engine guard and highway peg design. Their innovative styles not only look great but also function well with bars that include built-in or even fold-down footpegs such as those on the Twinbar®. With something for every ride, mild to wild, your customers will find their perfect bars in this broad line-up.

LINBAR® FRONT HIGHWAY BARS

0505-1138

•Made from 1 1/4” high-strength steel for long-lasting durability •Precision bent and welded for a perfect fit every time •Neoprene O-rings provide traction in all climates •Available in a chrome-plated or glossy black powder-coat finish U.S. Patent #D361311 NOTE: Not recommended for use with extended forward controls or extended floorboards.

PART # DESCRIPTION FOR 00-11 FLSTC, FLSTF AND FLSTN DS-190065 0505-1138

SUG. RETAIL

Chrome Glossy black powder coat

$349.95 349.95

ONE-PIECE HEATED TOURING SEATS

•Dual-zone high/low heat settings for driver and passenger right on the side of the seat •Illuminated switches •Does not require any OE controllers or switches to function •Constructed with extra rugged, triple-layered fiberglass •Wire harness hooks to accessory port in front of battery; seat has power only when the ignition key is turned on and accessory toggle switch below the handlebars is flipped up •Mustang’s one-piece touring design provides the rider and passenger with the fullest, most comfortable seat possible •Baseplate is open in the middle to accept a Mustang or stock H-D driver backrest kit 0801-0601 •17” W front bucket, 14” W rear seat •Seat will fit with a handrail •Made in the U.S.A.

PART # DESCRIPTION SUG. RETAIL FOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS 0801-0601

Plain

$749.95

PART # DESCRIPTION SUG. RETAIL FOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS (CONT) 0801-0602

Studded, chrome

$779.95

PART # DESCRIPTION SUG. RETAIL FOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS (CONT) 0801-0603

Studded, black

$779.95

1011-2663 1010-1018

1010-1017 1011-2664

POWER X INTAKE

•Air is power and Boyesen has channeled that power like never before •Patented X-Wing design for more power and acceleration; X-Wing venturi increases air speed for added throttle response •Complete kit includes backing plate with internal breather passageways, filter and mounting hardware •Oil-free/washable filter is a poly cotton blend with an extra-large filter area for increased airflow; filters to 40 microns •Available in polished silver or matte black finish •Accepts stock air filter cover

PART # DESCRIPTION FOR 08-11 FLHT, FLHR, FLHX, FLTR AND H-D FL TRIKE MODELS 1010-1017 1010-1018

6

Polished silver Matte black

SUG. RETAIL $229.95 229.95

CUSTOM AIR CLEANER ASSEMBLIES

•Increases horsepower with proper carburetor calibration •Mount directly to the carburetor •Designed to fit most models equipped with various carburetors

PART #

DESCRIPTION

1011-2663 For Bendix-Tillotson carbs to 75 1011-2664 For Linkert early 4-bolt model carbs

SUG. RETAIL $79.95 71.95


0601-1710

0703-0376

0601-1712

CLIP-ON HANDLEBARS

•A great way to give your bike that custom Cafe Racer look while providing a surprisingly comfortable riding position due to their “zero handlebar drop angle” configuration •Super-clean design features all-CNC-machined billet aluminum clamps and handlebars and includes superstrong alloy mounting hardware •Bars are 1” diameter, 12” long aluminum, constructed from strong 1/8” thick-wall 6061 T-6 tubing •Available in your choice of hard black anodized and raw aluminum finishes •Made in the U.S.A.

PART # DESCRIPTION FOR MODELS WITH 39MM FORK TUBES

SUG. RETAIL

0601-1710 0601-1711

Black anodized finish Raw aluminum finish

0601-1712 0601-1713

Raw anodized finish Black aluminum finish

0703-0377

•A great replacement for your hard-to-remove stock gas cap •Made with finger serrations for a much easier removal over the stock smooth-sided gas cap •Super-clean and low-profile design features all CNCmachined billet aluminum construction throughout •After being tightened down, the cap can rotate to any position to align design pattern •Clear anodized finish •High-quality gas cap base has right-hand threads and is vented •Dimensions: 3” diameter, 1/4” thick at the edge, and 9/16” thick in the center •Made in the U.S.A.

PART # DESCRIPTION FOR L96-11 H-D MODELS

0703-0376 0703-0377 0703-0378

SUG. RETAIL

JM U.S.A. Joker Smooth

$59.95 59.95 59.95

209.95 209.95

0640-0557

0640-0552

0640-0555

COMPLETE 41MM FORK TUBE INTERNALS KIT

0640-0558

BILLET ALUMINUM MIRRORS WITH CLEAR GLASS

•Contains everything needed to replace all clips, bushings, springs, dampeners, seals and chrome top caps on most Harley-Davidson 41mm fork tubes (except models with cartridge forks)

•Unique stainless steel pivot rides in a special nylon bushing; mirror head will never lose adjustment or rust at the pivot •Unsightly adjustment screws on the back of the mirror head are eliminated •CNC-machined from billet aluminum with a chrome or black finish •Can be installed on all 84-11 H-D clutch or brake housings; all necessary hardware included •Sold each

TEARDROP 51/2” X 31/2” DESCRIPTION

SUG. RETAIL

0640-0552 Smooth head w/ cutout stem, left; 6” x 41/4” stem length 0640-0554 Smooth head w/ cutout stem, right; 6” x 41/4” stem length 0640-0556 Ball-milled head w/ ball-milled stem, left; 6” x 41/4” stem length 0640-0558 Ball-milled head w/ ball-milled stem, right; 6” x 41/4” stem length

$99.95 99.95

0640-0553 Smooth head w/ cutout stem, left; 6” x 41/4” stem length 0640-0555 Smooth head w/ cutout stem, right; 6” x 41/4” stem length 0640-0557 Ball-milled head w/ ball-milled stem, left; 6” x 41/4” stem length 0640-0559 Ball-milled head w/ ball-milled stem, right; 6” x 41/4” stem length

99.95 99.95

BLACK

0703-0377

$209.95 209.95

FOR MODELS WITH 41MM FORK TUBES

PART # CHROME

GAS CAPS

0703-0378

99.95 99.95

99.95 99.95

PART #

DESCRIPTION

0414-0398

Complete fork tube internals kit

SUG. RETAIL $149.95

HANDLEBAR EXTENSION WIRING KITS

•Saves time by streamlining handlebar wiring jobs •Kits include all the materials necessary to extend the wires for hand controls •Terminals crimped on one end •Cut-to-length design will accommodate up to 20” Apehanger handlebars •Includes OEM color matching wires and heat shrink •Made in the U.S.A.

PART #

2120-0383

DESCRIPTION

2120-0382 For 96-06 universal application (except FLT, FLHT, FLHR, FLHX, FLTR models) 2120-0383 For 07-11 universal application (except FLT, FLHT, FLHR, FLHX, FLTR models) 2120-0384 For 96-06 FLT, FLHT, FLHR, FLTR models 2120-0385 For 07-11 FLT, FLHT, FLHR, FLTR models

SUG. RETAIL $34.95 34.95 59.95 59.95

7


1401-0323 1401-0317

1401-0318

1401-0324

FRONT FENDERS

•Raw stamped steel construction •Measure approximately 6” W (inside) •Available with or without trim holes •Mount with OEM hardware

PART # DESCRIPTION FOR 00-11 FLT/FLHT MODELS 1401-0317 1401-0318

Fender w/o trim holes; repl. OEM #59045-00 Fender w/ trim holes; repl. OEM #59093-00B

SUG. RETAIL $99.95 99.95

PART # DESCRIPTION FOR 87-99 FLT/FLHT MODELS 1401-0323 1401-0324

SUG. RETAIL

Fender w/o trim holes; repl. OEM #59045-98 Fender w/ trim holes; repl. OEM #59093-87

$99.95 99.95

1701-0373

REAR FENDER

•Raw stamped steel construction; measures approximately 71/4” wide (inside) •Original-style fender with taillight mount •Accepts OEM fender struts and mounting hardware

1701-0374

CHROME BRAKE CALIPERS

•Direct bolt-on design •Calipers include brake pads and bleeder screws •Sold each

PART # DESCRIPTION FRONT FOR 08-11 FLHT, FLTR, FLHR, FLHX AND H-D FL TRIKE 1701-0374 1701-0373

Left; repl. OEM #43027-08 Right; repl. OEM #44023-08

1701-0375

For 08-11 FLHT, FLTR, FLHR, FLHX; repl. OEM #44080-08B

REAR CALIPER

1701-0375

PART #

DESCRIPTION

1401-0330

For 82-93 XL models; repl. OEM #59674-81A

SUG. RETAIL $99.95

0214-0589

SUG. RETAIL $229.95 229.95

229.95

0214-0590

AXLE ADJUSTER SPACERS

•Steel construction with a chrome-plated finish

PART #

DESCRIPTION

0214-0589 0214-0590

For 00-07 FXST/FLST; repl. OEM #47577-00 (pr.) For 08-11 FXST/FLST; repl. OEM #41694-08 (ea.)

SUG. RETAIL $29.95 13.95

8.8MM SPARK PLUG WIRE SET

•Constructed with silicone throughout the jacket, insulation and core to deliver high-temperature resistance •Rated at SAE Class E J2031 with a continuous operating temperature of 450° F •Made in the U.S.A.

PART #

DESCRIPTION

2104-0227

For 09-11 FLHT, FLHR, FLHX, FLTR and FL Trike models

8

MINI TOGGLE SWITCHES

•5 AMP, 1/4” hole mini toggle switches •Made in the U.S.A.

SUG. RETAIL $19.95

2106-0149

PART #

DESCRIPTION

2106-0149 2106-0150

Mini high/low beam toggle switch Mini Air Ride toggle switch

2106-0150

SUG. RETAIL $9.95 9.95


XL CAMS “Y” CAMS

•”PB+” exhaust cams only (#s 1 and 4) •Use with stock P intake cams for bolt-in power with stock 1000cc engines; stock springs are okay and no head work is required •Made in the U.S.A.

•Biggest available four-cam set that does not require head work; however, some 82 engines may require spring spacing •Uses stock springs and provides great mid-range and upper-end power •Use with 9.0:1 to 10.0:1 compression ratios for best power gain

NOTE: 81-E84 cam gear kits (with generators) do not have tachometer drive gears.

NOTE: 81-E84 cam gear kits (with generators) do not have tachometer drive gears. L84-85 cam gear kits (with alternators) do not have generator.

XL CAMS

“PB+” EXHAUST CAMS

PART #

DESCRIPTION

0925-0589 0925-0588 0925-0587

For L84-85 XL For 81-E84 XL For 57-70 XL

GRIND OPEN CLOSE PB+ EXHAUST CAMS Intake 34° Exhaust 43°

40° 31°

SUG. RETAIL $203.95 203.95 213.95

DURATION @ .053

VALVE LIFT

LIFT @ TDC

254° 254°

.400 .410

.200 .192

PART #

DESCRIPTION

0925-0596 0925-0595 0925-0594

For L84-85 XL For 81-E84 XL For 57-70 XL

GRIND “Y”

Intake Exhaust

SUG. RETAIL $407.95 407.95 427.95

OPEN

CLOSE

DURATION @ .053

VALVE LIFT

35° 53°

47° 29°

262° 262°

.425 .425

2040-0671

2040-0802

Shown with one set of 2040-0800 installed in each saddlebag

2040-0805

BULLET LED MARKER/ SIGNAL LIGHT KITS

•Choose kits with standard or hooded bezels, amber or red lights and titanium-coated black chrome or polished stainless steel finish •Great looking, easy-to-install lights include six pairs of lenses 2040-0807 in every kit: flat, domed and bullet, each pair in clear and smoked •Twenty-five highly visible, vibration-resistant LEDs that will last more than twenty times longer than traditional filament bulbs •Three-wire design compatible with brake, turn and running light functions •Corrosion-resistant 304 stainless ring, injection-molded high-impact ABS and polycarbonate internal components and water-resistant wire grommets provide long-lasting durability and IP66 waterproof rating •Universal post installation is perfect for forward or rearward mounting; hooded trim ring can be set at 12, 3, 6 and 9 o’clock positions •Kits include two lights, plus instructions, extra mounting studs, wires and two load resistors (if needed to balance the bike’s signal flash rate) •Measure: 3.25” L x 2” D (standard bezel); 3.5” L x 2” D (hooded bezel) •Not DOT approved

PART # DESCRIPTION POLISHED STAINLESS LED BULLET LIGHT KITS

SUG. RETAIL

2040-0802 2040-0803 2040-0804 2040-0805

W/ W/ W/ W/

standard trim ring and red LED hood trim ring and red LED standard trim ring and amber LED hood trim ring and amber LED

$129.95 129.95 129.95 129.95

2040-0806 2040-0807 2040-0808 2040-0809

W/ W/ W/ W/

standard trim ring and red LED hood trim ring and red LED standard trim ring and amber LED hood trim ring and amber LED

129.95 129.95 129.95 129.95

TITANIUM-COATED (BLACK CHROME) LED BULLET LIGHT KITS

2040-0801

LED SADDLEBAG MARKER/SIGNAL LIGHT KITS

•Saddlemen’s new 21/4” flush-mounted LED kits permit easy installation of lights in the back of saddlebags for a clean, custom look •Kits are available with titanium-coated black chrome or bright polished stainless trim rings with amber lights and multi-faceted clear lenses •Flush-mounted universal design will mount on the rear surface of most hard or soft saddlebags •Twenty-five highly visible, vibration-resistant LEDs last more than twenty times longer than traditional filament bulbs •Three-wire design is compatible with brake, turn and running light functions •Corrosion-resistant 304 stainless steel mounting ring, injection molded high-impact ABS and polycarbonate internal components and water-resistant power plugs provide long lasting durability and IP66 waterproof rating •Everything you need for easy installation, including instructions for Saddlemen S4 Rigid-Mount, Specific-Fit Quick-Disconnect and Rigid-Mount Specific-Fit Teardrop saddlebags, two lamps plus wires, waterproof electrical connectors, four load resistors (if needed to balance the bike’s signal flash rate) and gaskets to keep your saddlebag weather-resistant •Not DOT approved

PART # DESCRIPTION KITS WITH POLISHED STAINLESS TRIM RING

SUG. RETAIL

2040-0800 2040-0671

Amber LED Red LED

$99.95 99.95

2040-0801 2040-0672

Amber LED Red LED

99.95 99.95

KITS WITH TITANIUM-PLATED (BLACK CHROME) TRIM RING

9


CYCLE ELECTRIC INC.

Electronics are the nerve center of any bike and here is a company dedicated to producing the highest quality, longest lasting electrical charging systems and components for American-made V Twins from 1936 to current. They do it all in their Brookville, Ohio factory where all parts are tested individually and then again as an assembly by craftsmen whose goals are both quality and customer service. The results are components with higher output and greater durability than the originals they replace.

2112-0711 2112-0712

2112-0714 2112-0713

REPLACEMENT REGULATORS FOR 3-PHASE 50A CHARGING KITS •Made in the U.S.A.

PART # DESCRIPTION REPLACEMENT REGULATORS

2112-0711 2112-0712

SUG. RETAIL

For kit PART #2112-0412 For kit PART #s 2112-0407, 2112-0408

$215.95 181.95

PART # DESCRIPTION REPLACEMENT REGULATORS (CONT)

2112-0713 2112-0714

SUG. RETAIL

For kit PART #s 2112-0409, 2112-0410 For kit PART #2112-0411

$193.95 224.95

OPTIMATE 1

3-STEP 900MA BATTERY CHARGER/MAINTAINER

•The OptiMate 4 saves neglected, deep-discharged batteries that other smart chargers can’t •Ideal for all AGM, GEL and standard filler cap batteries from 3 to 50aH •IP64 weatherproof sealed enclosure with built-in mounting option •Now compatible with either conventional or CAN-bus motorcycle electrical systems •Control panel with 10 LEDs displays all vital battery information •Cable bushings avoid insulation stress in ultra-cold temperatures •SAE weatherproof connections •Provides optimal maintenance of your battery during long-term storage, achieved by its gentle maintenance cycle which automatically allows the battery to rest for 30 minutes of each hour of the maintenance cycle while it remains connected •Includes fused eyelet connector for permanent mounting and battery clip set for bench charging

•Automatic charger for 12V lead-acid batteries of all types, with standard filler caps, or sealed (MF) maintenance-free and GEL •Ideal for maintaining batteries of seasonally used or stored vehicles of all types •Three-step charging program ensures effective charging of the battery •Totally safe for prolonged connection to the battery, without risk of overcharging •Easy to use, connect to battery, then to the power socket and the rest is automatic •An auto-resetting thermal fuse switches off the charger’s output circuit if the internal temperature for any reason exceeds a safe limit, to protect the charger from burn-out •Includes weatherproof connector with eyelets for permanent connection and battery clips for bench charging

PART #

DESCRIPTION

PART #

DESCRIPTION

3807-0100

Optimate 4

3807-0101

Optimate 1

OPTIMATE 4 DUAL PROGRAM

WEATHERPROOF DESULFATING BATTERY CHARGER/MAINTAINER

10

SUG. RETAIL $74.95

SUG. RETAIL $33.95


HI-4N IGNITION MODULE

HI-4N MULTI-FUNCTION PERFORMANCE IGNITION KIT WITH SINGLE-FIRE COIL

•HI-4N ignition module features a one-piece machined aluminum housing that reduces vibration and improves heat dissipation and reliability •Improved kickstart algorithm design – starts as easily as with points •BCD switches with solid detent and legible markings allow easy and repeatable adjustments of mode, advance rate and rev limit •Single-fire and dual-fire function built into a single module •Flexible wiring harness makes installation easier •Initial timing marks allow precise adjustment and re-installation •Sensor cover integrated into the housing to provide protection during installation •Kit also includes Crane Cams single-fire coil and Crane Cams 8.5mm double silicone premium quality spark plug wires •Made in the U.S.A.

PART #

DESCRIPTION

2101-0266

For 84-99 Big Twin Evolution (except EFI models), 70-84 Shovelhead and 71-03 XL (except 1200S)

DESCRIPTION

DESCRIPTION

2101-0265

For 84-99 Big Twin Evolution (except EFI models), 70-84 Shovelhead and 71-03 XL (except 1200S)

SUG. RETAIL $296.95

$475.95

VT-I V-TWIN ELECTRONIC IGNITION SYSTEM

•The easiest points conversion on the market •Remove old points and condensor, install the XR-i on the supplied adapter plate and wiring, and done •Fits under the stock cone cover so you keep the factory look; perfect for restoration projects •Has built-in adjustable rev limiter (4000 to 8000 rpm) •Voltage depended dwell control for optimal coil saturation •Operates down to 7V for reliable starting, a must for kick-start engines •Unit is fully sealed from moisture and dirt •Delivers more accurate timing •Made in the U.S.A. 2105-0107 For 70-78 Shovelhead; will also fit 79-99 Big Twin (requires mechanical advance) and all 36-69 Knucklehead/Flathead/Panhead/Shovelhead w/ generator if aftermarket timers designed for 12V “cone” style ignition systems

PART #

SUG. RETAIL

XR-I POINT REPLACEMENT IGNITION SYSTEM

PART #

•Updated version of the popular Crane HI-4 ignition •More power than the stock ignition •Single-fire and dual-fire function built into a single module •All-metal housing provides improved heat dissipation •Ignition advance and timing degree markings are on the metal flange •Convenient cable notch in the housing makes installation easier and prevents damage to the cable •Sensor and magnet housings are built into the all-metal back plate to protect the sensors from damage during installation •Sensor housings contain advanced flux concentrators with hightemperature-resistant samarium/cobalt magnets for accurate, reliable ignition triggering •Electronics are fully enclosed to resist vibration, moisture and dirt •All electronics are mounted directly to the metal housing, which acts as a heat sink •Four rotary switches for ignition mode selection, advance rate, and rev limit •Switches provide accurate, repeatable settings •Coil and plug wires are sold separately •Made in the U.S.A.

SUG. RETAIL

$124.95

•Ultra-reliable dual fire electronic ignition system •Includes special trigger rotor for use with traditional mechanical advance mechanism (sold separately) •Precise digitally set RPM limiter (200 rpm steps from 5,200 to 7,000 rpm) •Status LED for easy static timing •Electronic dwell control for maximum ignition energy at high rpm and reduced current draw at low RPM •Compatible with most original equipment and aftermarket dual fire ignition coils (3-5 ohms primary resistance) •Easy installation – simple two-wire hookup to coil •Hall effect sensor detects teeth on special trigger rotor and provides very stable spark timing •Operates down to below 6 volts for reliable starting under all conditions, including kick start •Fully encapsulated construction using surface mount electronics – waterproof and highly resistant to vibration and shock •Over-temperature protection; rated to operate at 125°C (260°F)

PART #

DESCRIPTION

2101-0267

For 84-99 Evolution Big Twin, 70-84 Shovelhead and 86-03 XL (except 1200S)

SUG. RETAIL $139.95

11


HOGTUNES

Owner Mike “Pez” Pesdirz and the folks at Hogtunes continue to amaze riders everywhere with their ever expanding line of high-performance audio products and accessories. Their in-house state-of-the-art sound labs mean that they are able to continually develop, test and refine products specifically designed for motorcyclists. And it is the motorcyclists who own Hogtunes systems who are some of the best salesmen as they have fellow riders asking for Hogtunes by name.

MEMPHIS SHADES SPEAKER SYSTEM KIT

•Includes custom “pod” with dual 4.25” speaker, 50 watt amp with USB charge port, audio perch with built-in volume control and all required hardware and wiring •Fits all Memphis Shades Batwing fairings •Measures approximately 1111/16” W x 51/4” T x 51/2” D

PART #

DESCRIPTION

NOTE: Kit may not fit if gauges are riser mounted.

4405-0218

Memphis Shades speaker system kit

DEEP CUT OIL PRESSURE GAUGE KITS

4405-0240

DEEP CUT FRONT SPEAKER GRILLES •Made of 6061 T-6 billet aluminum •Sold in pairs •Made in the U.S.A.

4405-0240 4405-0239

Chrome Black

$399.95

2212-0370

•Finally a clean way to mount an oil pressure gauge on Big Twin and Sportster engines; bracket mounts gauge to rear rocker box •Features stainless housing and glass lens filled with vibration dampening glycerin •Includes a 0-60 lb. liquid-filled gauge, billet bracket/cone, stainless steel hose assembly and necessary hardware

4405-0239

PART # DESCRIPTION FOR 96-11 FLHT/FLHX AND H-D FL TRIKE MODELS

SUG. RETAIL

NOTE: Check clearance between gauge and gas tank.

SUG. RETAIL $139.95 139.95

PART #

DESCRIPTION

2212-0370 2212-0371 2212-0369

For 99-11 Twin Cam For 93-03 XL w/ mid controls only For S&S w/ billet rocker boxes

SUG. RETAIL $189.95 199.95 189.95

3501-0697

3501-0698

BILLET SADDLEBAG EXTENSIONS

3501-0696 •Chrome-plated, billet aluminum extensions create a custom look •Easy bolt-on installation to any 93-11 FL model with hard saddlebags •No painting required •Available with exhaust cut-outs for single or dual exhaust systems or without cutouts for “shorty” exhausts •Available in chrome plated or black powder-coat finish with contrasting machined grooves •Made in the U.S.A.

PART # CHROME

3501-0696 3501-0697 3501-06981

DESCRIPTION W/ cut-outs, for dual exhausts W/ cut-out, for right exhaust W/o cut-out

SUG. RETAIL $399.95 399.95 399.95

PART # BLACK

3501-0699 3501-0700 3501-07011 1

12

3501-0699

DESCRIPTION W/ cut-outs, for dual exhausts W/ cut-out, for right exhaust W/o cut-out

For use with short turn-down mufflers.

SEPTEMBER 2011 | 9901-1026

SUG. RETAIL $399.95 399.95 399.95


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.