Molded Cable Assemblies
8.1
8
Table of Contents Molded Cable Assemblies Page No. Introduction 8.2 D-Subminiature Assemblies with Straight Handles 8.3–8.5 Shielded 9-Position: Foil Shielded Retractile Cable (handle one end) 8.3 Shielded 9-Position: Foil Shielded Cable 8.3 Shielded 15-Position: Foil Shielded Cable 8.3 Shielded 15-Position: Foil+Braid Shielded Cable 8.3 Shielded 25-Position: Foil Shielded Cable 8.4 Shielded 25-Position: Foil+Braid Shielded Cable 8.4 Shielded 37-Position: Foil+Braid Shielded Cable Shielded 50-Position: Foil Shielded Cable Shielded SCSI Cable Assembly GPIB Assemblies Unshielded Molded PVC Connectors: Foil+Braid Shielded Cable Shielded Die-Cast Connectors: Foil+Braid Shielded Cable Shielded Molded PVC Connectors: Foil+Braid Shielded Cable Shielded DIN Cable Assemblies 5-Position: Foil Shielded Cable 5-Position: Foil+Braid Shielded Cable 8-Position: Foil Shielded Cable 5-Position: Foil+Serve Retractile Cable DIN Pin Configurations: Face Views Modular Keyboard Assemblies 4-Position: Unshielded Retractile Cable 6-Position: Unshielded Retractile Cable 8-Position: Unshielded Retractile Cable 8-Position: Foil Shielded Retractile Cable Modular Plug Wiring Schemes Parallel Interface Assembly Technical Information D-Subminiature Retention Systems How To Measure A Molded Cable Assembly
Please refer to “Terms of Use of Master Catalog” on page 22.22
8.5 8.5 8.6 8.7 8.7 8.7 8.7 8.8–8.9 8.8 8.8 8.8 8.9 8.9 8.10 8.10 8.10 8.10 8.10 8.10 8.11 8.12 8.12 8.12
M O L D E D
C A B L E
A S S E M B L I E S
8.2
Introduction
Quality Construction
Wiring Patterns
Belden® molded cable assemblies are designed for long life and reliable performance in a variety of input/output (I/O) and keyboard interface applications. Among the many features of the cable assemblies are these performance-enhancing attributes:
Standard wiring is point-to-point on most assemblies. Special wiring is available upon request.
Shielding Molded handles are 100% shielded (where used) to assist in FCC compliance while guarding against EMI and RFI. Shield continuity is maintained through the entire length of the assembly. The connector shield is connected to both the connector shell and the cable shield. This provides a low resistance ground path to optimize shield performance. Handles Straight or right angle handles are available for different connecting situations. Standard molding is PVC. Connectors Connectors consist of tin-plated shells with grounding indents on male connectors. Pins and sockets are constructed of brass or phosphor-bronze base with gold selectively plated over nickel. Retention Systems
Cables For standard assemblies, Belden utilizes three standard cable configurations for tailoring a cable to a specific electrical environment. The cable configurations are as follows: ●
General Purpose Unshielded: An economical assembly where electrical noise/interference is not a problem.
●
General Purpose Shielded: An overall foil shielded assembly for use in situations where some noise/interference is experienced or anticipated.
●
Super Shield: A foil plus braid shield provides extra protection in areas of moderate to heavy noise/interference.
Most of our molded cable assemblies are available from stock in a wide variety of handles, cables, colors, retention systems, and wiring patterns. Many of these are available off the shelf from distributors. If you have a new or unusual application or you cannot find molded cables in this catalog section that meet your technical requirements, contact Technical Support at 1-800-BELDEN-1.
Molded Cable Assemblies Packaging
Belden offers several types of retention systems. They include: ●
Friction: Pin/contact force holds connectors mated.
●
Screw: Retaining screws mate with female screwlocks. Straight handle uses two screws; right angle handle uses one screw. Screws are #4-40 thread of plated steel with stainless steel clips.
●
Slide Lock: Fingertip-operated slide mechanism holds mated connectors securely. Slide lock clip is stainless steel with plated screw, washer, and hex nut.
●
Spring Latch: Stainless steel latch mates with latching blocks (special orders only).
●
Jack Screw: Two captive jacks crews mate securely with female screwlocks. Zinc plated, #4-40 thread screws with large knurled heads for easy fingertip connect/disconnect.
Unless otherwise indicated, molded cable assemblies are shipped in individual packages or plastic bags with printed part numbers, descriptions and an area to indicate the retail price.
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
M O L D E D
C A B L E
A S S E M B L I E S
8.3
D-Subminiature Assembly Shielded 9-Position and 15-Position
Part No.
No. of Cond.
Length of Body Retracted Inch
mm
Length of Tail
Extended Inch
Connector End
mm
Inch
mm
Other End Inch
mm
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Inch
Jacket Thickness
mm
Inch
mm
Nominal OD Inch
mm
.250
6.35
Foil Shield (General Purpose) • Retractile • Polypropylene Insulation • Black Polyurethane Jacket 49911A 9 18 457 90 2286 6 152 18 457 .15 .065 26 Overall 20 (42x36) .006 (19x38) Foil Polyurethane jacket provides superior retractile properties at a reasonable cost. Molded handles are 100% shielded to assist in FCC compliance and guard against EMI/RFI. Tinned Copper All connectors are tin-plated with detents for a positive ground connection. [.53] The end opposite the connector is stripped. Jack screw retention on male connector.
1.65
30V 60°C, UL AWM Style 20197
Contact View
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
Conductors AWG (stranding) [Dia. in mm]
UL NEC/ (C)UL CEC Type
Insulation Thickness
Shield Type
Drain Wire
Jacket Thickness
Nominal OD
Inch
mm
Inch
mm
Inch
mm
.010
.25
.032
.81
.244
6.20
9-Position Shielded D-Sub • Straight Handle Both Ends • For RS-449 applications Foil Shield 49900A 49901A 49902A 49905A 49906A 49907A
(General Purpose) • Semi-rigid PVC Insulation • Chrome PVC Jacket NEC: 24 Overall 24 (7x32) 9 5 1.5 Male/Male CM (7x32) Foil 9 10 3.0 Male/Male Tinned Copper 9 25 7.6 Male/Male [.61] 9 5 1.5 Male/Female 9 10 3.0 Male/Female 9 25 7.6 Male/Female
Molded handles are 100% shielded to assist in FCC compliance and guard against EMI/RFI. All connectors tin-plated and male connectors have detents for positive ground connection. Wiring is point-to-point with the shield to connector shell. Jack screw retention on both connectors.
Contact View
Contact View
300V 80°C, UL AWM Style 2464
15-Position Shielded D-Sub • Straight Handle Both Ends • For any 15-pin application exposed to high-noise environment Foil Shield (General Purpose) • Semi-rigid PVC Insulation • Chrome PVC Jacket NEC: Overall 24 (7x32) 24 49721A 15 10 3.0 Male/Male CM Foil (7x32) 49725A 15 5 1.5 Male/Female Tinned Copper 49726A 15 10 3.0 Male/Female [.61]
.010
.25
.032
.81
.284
7.21
Molded handles are 100% shielded to assist in FCC compliance and guard against EMI/RFI. All connectors tin-plated and male connectors have detents for positive ground connection. Wiring is point-to-point with the shield to connector shell. Jack screw retention on both connectors.
300V 80°C, UL AWM Style 2464 Contact View
Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation NEC: 24 49740A 15 5 1.5 Male/Male CM (7x32) 49745A 15 5 1.5 Male/Female Tinned Copper 49746A 15 10 3.0 Male/Female [.61] 49747A 15 25 7.6 Male/Female
Contact View
• Chrome PVC Jacket Overall None .010 .25 Foil + 65% Braid
.035
.89
.300
7.62
Molded handles are 100% shielded to assist in FCC compliance and guard against EMI/RFI. All connectors tin-plated and male connectors have detents for positive ground connection. Wiring is point-to-point with the shield to connector shell. Jack screw retention on both connectors.
300V 80°C, UL AWM Style 2464 Contact View
Contact View
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
8 • Molded Cable Assemblies
9-Position Shielded D-Sub • Male Straight Handle One End • For keyboard-to-CRT use where 9-pin retractile is desired
M O L D E D
C A B L E
A S S E M B L I E S
8.4
D-Subminiature Assembly Shielded 25-Position
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Jacket Thickness
Nominal OD
Inch
mm
Inch
mm
Inch
mm
.010
.25
.032
.81
.339
8.61
25-Position Shielded D-Sub • Straight Handle Both Ends • For RS-232 applications Foil Shield (General Purpose) • Semi-rigid PVC Insulation • Chrome PVC Jacket NEC: 24 Overall 24 (7x32) 49668A 25 5 1.5 Male/Male CM (7x32) Foil 49669A 25 10 3.0 Male/Male Tinned Copper 49673A 25 5 1.5 Male/Female [.61] 49674A 25 10 3.0 Male/Female 49675A 25 25 7.6 Male/Female 49676A 25 50 15.2 Male/Female Molded handles are 100% shielded to guard against EMI/RFI where indicated. All connectors are tin-plated and male connectors have detents to allow for a positive shield to ground connection. Wiring is point-to-point with shield to connector shell. Jack screw retention on both connectors.
300V 80°C, UL AWM Style 2464
Contact View
Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation NEC: 24 49615A 25 5 1.5 Male/Female CM (7x32) 49616A 25 10 3.0 Male/Female Tinned Copper 49617A 25 25 7.6 Male/Female [.61]
Contact View
• Chrome PVC Jacket Overall Foil + 65% Braid
Molded handles are 100% shielded to guard against EMI/RFI where indicated. All connectors are tin-plated and male connectors have detents to allow for a positive shield to ground connection. Wiring is point-to-point with shield to connector shell. Jack screw retention on both connectors.
300V 80°C, UL AWM Style 2464
Contact View
Contact View
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
M O L D E D
C A B L E
A S S E M B L I E S
8.5
D-Subminiature Assembly Unshielded 25-Position, Shielded 37-Position and 50-Position
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Inch
mm
Jacket Thickness Inch
mm
Nominal OD Inch
mm
Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation NEC: 24 49950A 36 5 1.5 Male/Male CM (7x32) 49951A 36 10 3.0 Male/Male Tinned Copper 49952A 36 25 7.6 Male/Male [.61] 49955A 36 5 1.5 Male/Female 18 Pairs 49956A 36 10 3.0 Male/Female 49957A 36 25 7.6 Male/Female
• Chrome PVC Jacket Overall None .010 .25 Foil + 65% Tinned Copper Braid
.045
1.14
.480
12.19
Molded handles are 100% shielded to assist in FCC compliance and guard against EMI/RFI. All connectors are tin-plated and male connectors have detents to allow for a positive shield to ground connection. Wiring is point-to-point with shield to connector shell and pin #1. Jack screw retention on both connectors.
300V 80°C, UL AWM Style 2464
Contact View
Contact View
50-Position Shielded D-Sub • Straight Handle Both Ends • For high-density applications where assembly is exposed to high noise environment Foil plus Braid Shield (General Purpose) • Polyethylene Insulation • Chrome PVC Jacket 49760A 50 5 1.5 Male/Male .25 NEC: 26 Overall 22 (7x30) .010 CM (7x34) Foil 49761A 50 10 3.0 Male/Male Tinned Copper + 91% 49765A 50 5 1.5 Male/Female [.48] Tinned 49766A 50 10 3.0 Male/Female Copper 25 Pairs Braid Molded handles are 100% shielded to guard against EMI/RFI and
.049
1.24
.535
13.59
assist in FCC compliance. All connectors are tin-plated and male connectors have detents to allow for a positive shield to ground connection. Wiring is point-to-point with shield to connector shell. Jack screw retention on both connectors.
30V 80°C, UL AWM Style 2919
Contact View
Contact View
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
8 • Molded Cable Assemblies
37-Position Shielded D-Sub • Straight Handle Both Ends • For RS-449 applications where assembly is exposed to high noise environment
M O L D E D
C A B L E
A S S E M B L I E S
8.6
SCSI Cable Assembly SCSI-1 and SCSI-2 Shielded Straight and Right-Angled Handles
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Inch
mm
Jacket Thickness Inch
mm
Nominal OD Inch
mm
.535
13.589
SCSI-1 Assemblies (26 AWG) • Shielded Straight Handles • For SCSI (Small Computer Systems Interface) applications Foil plus Braid Shield (Super Shield) • Polyethylene Insulation • Chrome PVC Jacket NEC: 26 Overall 49802A 50 16.4 5 Male/Male 22 .01 CM (7x34) Foil (7x30) Molded handles are 100% shielded to guard against EMI/RFI and assist in FCC compliance. These assemblies have tin-plated connectors Tinned Copper + 90% TC and can be used in single-ended or differential configurations. Wiring is [.48] Braid per SCSI standard. 25 Pairs
.254
.049
1.245
30V 80°C, UL AWM Style 2919
Contact View
Contact View
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
M O L D E D
C A B L E
A S S E M B L I E S
8.7
GPIB (General Purpose Interface Bus) Assembly Unshielded and Shielded Connectors
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding)
Insulation Thickness
Shield Type
Drain Wire
Inch
mm
Jacket Thickness
Nominal OD
Inch
mm
Inch
mm
.035
.89
.350
8.89
Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation • Gull Gray PVC Jacket NEC: 6 Pairs: Overall 26 (7x34) .010 49642 23 3.3 1 Male/Female .25 26 (7x34) TC CM Foil Each End 10 Singles: + 90% 49643 23 6.6 2 Male/Female 26 (7x34) TC Braid Each End 1 Single: 49645 23 26.2 8 Male/Female 24 (7x32) TC Each End Molded connector is male/female design for easy stacking and comes with molded-in metric jack screws.
300V 80°C, UL AWM Style 2464
Contact View
Contact View
Shielded GPIB • Die Cast Connector • For use with electronic equipment that is IEEE-488 compatible Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation • Gull Gray PVC Jacket NEC: 6 Pairs: Overall 26 (7x34) .010 49635 23 3.3 1 Male/Female .25 26 (7x34) TC CM Foil Each End 10 Singles: + 90% 49636 23 6.6 2 Male/Female 26 (7x34) TC Braid Each End 1 Single: 49637 23 9.8 3 Male/Female 24 (7x32) TC Each End
.035
.89
.350
8.89
Die cast connector is male/female design for easy stacking and comes with molded-in metric jack screws.
300V 80°C, UL AWM Style 2464
Contact View
Contact View
Shielded GPIB • Molded PVC Connector • For use with electronic equipment that is IEEE-488 compatible Foil plus Braid Shield (Super Shield) • Semi-rigid PVC Insulation • Gull Gray PVC Jacket NEC: 6 Pairs: Overall 26 (7x34) .010 49733 23 1.6 .5 Male/Female .25 26 (7x34) TC CM Foil Each End 10 Singles: + 90% 49734 23 3.3 1 Male/Female 26 (7x34) TC Braid Each End 1 Single: 49735 23 6.6 2 Male/Female 24 (7x32) TC Each End 49736 23 9.8 3 Male/Female Each End 49737 23 13.1 4 Male/Female Each End
.035
.89
.350
8.89
Molded connector is male/female design for easy stacking and comes with molded-in metric jack screws.
300V 80°C, UL AWM Style 2464 Contact View
Contact View
TC = Tinned Copper
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
8 • Molded Cable Assemblies
Unshielded GPIB • Molded PVC Connector • For use with electronic equipment that is IEEE-488 compatible
M O L D E D
C A B L E
A S S E M B L I E S
8.8
DIN* Cable Assembly Shielded 3-Position, 5-Position and 8-Position
Part No.
No. of Cond.
Standard Lengths Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Inch
mm
Jacket Thickness Inch
mm
Nominal OD Inch
mm
5-Position Shielded DIN • Straight Handle One End • Used where a shielded conductor is desired and as a low cost alternative to a D-Sub Foil Shield (General Purpose) • PVC Insulation • Black PVC Jacket NEC: 26 Overall 49152A 5 10 3.0 CM (19x38) Foil Foil shielded for moderate-noise environments. Outer jacket stripped 1 inch. Tinned Copper [.51] 300V 80°C, UL AWM Style 2464. Packaged: B-25, S-25
26 (19x38)
.014
.36
.053
1.35
.251
6.38
.014
.36
.037
.94
.231
5.87
Contact View
Foil plus Braid Shield (Super Shield) • PVC Insulation • Black PVC Jacket NEC: 26 Overall 26 49153A 5 10 3.0 CM (19x38) Foil (19x38) Foil and braid shielded for high-noise environments. Outer jacket stripped 1 inch. Tinned Copper + 90% [.51] Tinned 300V 80°C, UL AWM Style 2464. Packaged: B-25, S-25 Copper Braid
Contact View
8-Position Shielded DIN • Straight Handle One End • Used where a shielded conductor is desired and as a low cost alternative to a D-Sub Foil Shield (General Purpose) • PVC Insulation • Black PVC Jacket NEC: 26 Overall 49154A 8 10 3.0 CM (19x38) Foil Foil shielded for moderate-noise environments. Outer jacket stripped 1 inch. Tinned Copper [.51] 300V 80°C, UL AWM Style 2464. Packaged: B-25, S-25
26 (19x38)
.014
.36
.052
1.32
.266
6.76
Contact View
*DIN Standard (Deutsche Industries Norm)
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
M O L D E D
C A B L E
A S S E M B L I E S
8.9
DIN* Cable Assembly Shielded 5-Position and 8-Position Retractile
Part No.
No. of Cond.
Length of Body Retracted Inch
Length of Tail
Extended
mm
Inch
Connector End
mm
Inch
mm
Other End Inch
mm
Conductors AWG (stranding) [Dia. in mm]
Shield Type
Drain Wire
Insulation Thickness Inch
mm
Jacket Thickness Inch
mm
Nominal OD Inch
mm
Foil plus Serve Shield (Super Shield) • Retractile • PVC Insulation • Black PVC Jacket 49103A 5 14.5 368.3 72.5 1841.5 12 304.8 18 457.20 26 Foil 26 (19x38) .014 (19x38) + 95% Shielded connectors maintain shield integrity and assist in FCC compliance. Utilizes 26 AWG conductor for low voltage drop. Ideal for higher noise situations. Tinned Copper Serve [.51] 300V 80°C, UL AWM Style 2464. Packaged: S-25
Contact View
.36
.058
1.47
.260
6.60
NEC: CM
DIN Pin Configurations • Face Views
3-Position
4-Position**
5-Position @ 180°
5-Position** @ 240°
6-Position**
7-Position**
8-Position
**Available by special order
*DIN Standard (Deutsche Industries Norm)
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
8 • Molded Cable Assemblies
5-Position Shielded DIN • Straight Handle • Standard friction-fit connectors mate easily with many microcomputer keyboard ports
M O L D E D
C A B L E
A S S E M B L I E S
8.10
Modular Keyboard Assemblies 4-Position, 6-Position and 8-Position with Retractile Cables Unshielded or Shielded Modular Plugs
Part No.
No. of Cond.
Length of Cord Body Retracted
Body Extended
Inch
Inch
mm
mm
Tail Length Inch
mm
Conductors AWG (stranding) [Dia. in mm]
Shield Type
Drain Wire
Insulation Thickness Inch
mm
Jacket Thickness Inch
mm
Nominal OD Inch
mm
4-Position Modular Plugs • Used to rapidly interconnect electronic computers and business machines Unshielded (General Purpose) • Retractile • Polypropylene Insulation • Black or CRT White Polyurethane Jacket 49440 4 15 381 67.5 1714.50 1 25.40 None None .006 .15 .030 .76 .093 2.36 26 (19x38) x x Positive locking latch prevents connector from vibrating loose. Polarized connector prevents improper insertion. No tools required for installation. Tinned Copper .198 5.03 [.51] 30V 60°C, UL AWM Style 20197. Packaged: B-25, S-25
6-Position Modular Plugs • Used to rapidly interconnect electronic computers and business machines Unshielded (General Purpose) • Retractile • Polypropylene Insulation • Black Polyurethane Jacket 49441 6 15 381 67.5 1714.50 1 25.40 None None .006 .15 .030 26 (19x38) Positive locking latch prevents connector from vibrating loose. Polarized connector prevents improper insertion. No tools required for installation. Tinned Copper [.51] 30V 60°C, UL AWM Style 20197. Packaged: B-25, S-25
.76
.093 x .258
2.36 x 6.55
8-Position Modular Plugs • Used to rapidly interconnect electronic computers and business machines Unshielded (General Purpose) • Retractile • Polypropylene Insulation • Black or CRT White Polyurethane Jacket 26 49442 8 15 381 67.5 1714.50 1 25.40 None None .006 .15 .030 .76 .100 2.54 (19x38) x x Positive locking latch prevents connector from vibrating loose. Polarized connector prevents improper insertion. No tools required for installation. Tinned Copper .314 7.98 [.51] 30V 60°C, UL AWM Style 20197. Packaged: B-25, S-25 Foil Shield* • Retractile • Polypropylene Insulation • Black Polyurethane Jacket 26 49402 7 15 381 67.5 1714.50 1 25.40 Foil 26 (19x38) (19x38) Positive locking latch prevents connector from vibrating loose. Polarized connector prevents improper insertion. No tools required for installation. Tinned Copper A longitudinal aluminum/polyester shield protects against ESD and EMI. [.51]
.006
.15
.030
.76
.100 x .314
2.54 x 7.98
30V 60°C, UL AWM Style 20197. Packaged: S-25
Contact View
Contact View
Modular Plug Wiring Schemes Cross wiring is standard on non-shielded constructions 1......................................4 2......................................3 3......................................2 4......................................1
Straight wiring is standard on shielded constructions 1......................................1 2......................................2 3......................................3 4......................................4
Pin #1
*In shielded versions, the drain wire is always the highest numbered position in the connector.
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
M O L D E D
C A B L E
A S S E M B L I E S
8.11
Parallel Interface Assembly
Part No.
No. of Cond.
Standard Lengths Gender Ft.
m
UL NEC/ (C)UL CEC Type
Conductors AWG (stranding) [Dia. in mm]
Insulation Thickness
Shield Type
Drain Wire
Inch
mm
Jacket Thickness Inch
Nominal OD
mm
Inch
mm
1.02
.370
9.40
Shielded • Foil plus Braid Shield (Super Shield) • Semi-rigid PVC NEC: 24 49502A 25 10 3.0 Male/Male CM (7x32) Universal 36-position ribbon connector (Centronics compatible) on one end and a 25-position D-Subminiature connector (IBM PC and PC-XT Tinned Copper compatible) on the other. Molded handles are 100% shielded to guard [.61] against EMI/RFI and assist in FCC compliance.
300V 80°C, UL AWM Style 2464
Contact View
Insulation • Chrome PVC Jacket Overall None .010 .25 .040 Foil + 65% Tinned Copper Braid
Contact View
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m
8 • Molded Cable Assemblies
Parallel Interface Assemblies • Centronics/D-Sub Connectors • For computer-printer parallel interface
M O L D E D
C A B L E
A S S E M B L I E S
8.12
Technical Information
D-Subminiature Retention Systems
Friction
Screw
Vertical Slide Lock
Horizontal Slide Lock
How to Measure a Molded Cable Assembly
Length
Length
Angled Handled Connector
Straight Handled Connector
Length
Length
GPIB
DIN
Coil Length
gth
gt Le n
n Le
Ta il
il Ta
h
Retractile Assemblies
F o r m o r e i n f o r m a t i o n , c o n t a c t B e l d e n Te c h n i c a l S u p p o r t : 1 - 8 0 0 - B E L D E N - 1 • w w w . b e l d e n . c o m