Panasonic-Automotive Relays-TX by SYNsCON

TESTING

2 A CAPACITY RELAY WITH HIGH SURGE VOLTAGE & HIGH BREAKDOWN VOLTAGE 15 .591

7.4 .291 8.2 .323

15 .591

7.4 .291 8.4 .331

mm inch

TX RELAYS

FEATURES • Breakdown voltage between contacts and coil: 2,000 V • Surge withstand between contacts and coil: 2,500 V • High contact capacity: 2 A 30 V DC • Surface-mount type available

SPECIFICATIONS Contact

Characteristics

Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1 A) Contact material Nominal switching capacity (resistive load) Max. switching power (resistive load) Rating Max. switching voltage Max. switching current Min. switching capacity ❇1 Nominal operating power

Single side stable

Expected life (min. operations)

2 A 30 V DC resistive Electrical (at 20 cpm) 1 A 30 V DC resistive

1 coil latching 2 coil latching Mechanical (at 180 cpm)

2 Form C 100 mΩ Gold-clad silver alloy 2 A 30 V DC 60 W 220 V DC 2A 10 µA 10 mV DC 140 mW (1.5 to 24 V DC) 270 mW (48 V DC) 100 mW (1.5 to 24 V DC) 200 mW (1.5 to 24 V DC) 108 105 5×105

Notes: ❇1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. (SX relays are available for low level load switching [10 µA 1 mV DC – 10 mA 10 V DC]) ❇2The upper limit for the ambient temperature is the maximum temperature that can satisfy the coil temperature rise. Under the packing condition, allowable temperature range is from –40 to +70°C –40°C to +158°F.

Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 By resistive method, nominal voltage applied to the coil; contact carrying current: 2 A. *3 Nominal voltage applied to the coil, excluding contact bounce time. 4 * Nominal voltage applied to the coil, excluding contact bounce time without diode. *5 Half-wave pulse of sine wave: 6 ms; detection time: 10 µs. *6 Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10 µs. *8 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT.

Initial insulation resistance*1 Between open contacts Initial breakdown Between contact sets voltage Between contact and coil Between open contacts Initial surge (10×160 µs) voltage Between contacts and coil (2×10 µs) Temperature rise*2 (at 20°C)

Min. 1,000 MΩ (at 500 V DC) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 2,000 Vrms for 1 min. (Detection current: 10 mA) 1,500 V (FCC Part 68) 2,500 V (Telcordia) Max. 50°C

Max. 4 ms (Approx. 2 ms) Operate time [Set time]*3 (at 20°C) [Max. 4 ms (Approx. 2 ms)] Max. 4 ms (Approx. 1 ms) Release time [Reset time]*4 (at 20°C) [Max. 4 ms (Approx. 2 ms)] Min. 750 m/s2 {75 G} Functional*5 Shock resistance Destructive*6 Min. 1,000 m/s2 {100 G} 196 m/s2 {20 G}, 10 to 55 Hz Functional*7 at double amplitude of 3.3 mm Vibration resistance 294 m/s2 {30G}, 10 to 55 Hz Destructive at double amplitude of 5 mm –40°C to +85°C (up to 24 V coil) Conditions for operation, transport and Ambient tem- –40°F to +185°F (up to 24 V coil) perature ❇2 –40°C to +70°C (48 V coil) storage*8 (Not freezing and –40°F to +158°F (48 V coil) condensing at low Humidity 5 to 85% R.H. temperature) Unit weight Approx. 2 g .071 oz

TX ORDERING INFORMATION Ex. TX Contact arrangement

Surface-mount availability

–

Operating function Terminal shape

Nil: Standard PC board terminal type or Nil: self-clinching terminal type SA: Standard surface-mount terminal type SL : High connection reliability surface-mount SL : terminal type SS: Space saving surface-mount terminal type

–

Coil voltage (DC)

Packing style

Nil: Standard PC 1.5, 3, 4.5, 5, 6, Nil: Tube packing board terminal or 9, 12, 24, 48* V Z: Tape and reel surface-mount packing(picked terminal from the 8/9/10/12 H: Self-clinching -pin side terminal Notes: 1. Tape and reel (picked from 1/3/4/5-pin side) is also available by request. Part number suffix “-X” is *48 V coil type: Single side stable only 2: 2 Form C

Nil: Single side Nil: stable L: 1 coil latching L2: 2 coil latching

needed when ordering. (ex.) TX2SA-3 V-X 2. Tape and reel packing symbol “-Z” or “-X” are not marked on the relay.

TYPES AND COIL DATA (at 20°C 68°F) 1) Standard PC board terminal type and self-clinching terminal type 1. Single side stable Part No. Standard PC board terminal TX2-1.5 V TX2-3 V TX2-4.5 V TX2-5 V TX2-6 V TX2-9 V TX2-12 V TX2-24 V TX2-48 V

Nominal voltage, V DC

Pick-up voltage, V DC (max.)

Drop-out voltage, V DC (min.)

1.5 3 4.5 5 6 9 12 24 48

1.13 2.25 3.38 3.75 4.5 6.75 9 18 36

0.15 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8

Nominal voltage, V DC

Set voltage, V DC (max.)

Reset voltage, V DC (max.)

1.5 3 4.5 5 6 9 12 24

1.13 2.25 3.38 3.75 4.5 6.75 9 18

Self-clinching terminal

Nominal voltage, V DC

Set voltage, V DC (max.)

Reset voltage, V DC (max.)

TX2-L2-H-1.5 V TX2-L2-H-3 V TX2-L2-H-4.5 V TX2-L2-H-5 V TX2-L2-H-6 V TX2-L2-H-9 V TX2-L2-H-12 V TX2-L2-H-24 V

1.5 3 4.5 5 6 9 12 24

1.13 2.25 3.38 3.75 4.5 6.75 9 18

Self-clinching terminal TX2-H-1.5 V TX2-H-3 V TX2-H-4.5 V TX2-H-5 V TX2-H-6 V TX2-H-9 V TX2-H-12 V TX2-H-24 V TX2-H-48 V

Nominal operating current, mA (±10%) 93.8 46.7 31 28.1 23.3 15.5 11.7 5.8 5.6

Coil resistance, Ω (±10%) 16 64.3 145 178 257 579 1,028 4,114 8,533

Nominal operating power, mW 140 140 140 140 140 140 140 140 270

Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36 57.6

Nominal operating power, mW 100 100 100 100 100 100 100 100

Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36

Nominal operating power, mW 200 200 200 200 200 200 200 200

Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36

2. 1 Coil latching Part No. Standard PC board terminal TX2-L-1.5 V TX2-L-3 V TX2-L-4.5 V TX2-L-5 V TX2-L-6 V TX2-L-9 V TX2-L-12 V TX2-L-24 V

Self-clinching terminal TX2-L-H-1.5 V TX2-L-H-3 V TX2-L-H-4.5 V TX2-L-H-5 V TX2-L-H-6 V TX2-L-H-9 V TX2-L-H-12 V TX2-L-H-24 V

Nominal operating current, mA (±10%) 66.7 33.3 22.2 20 16.7 11.1 8.3 4.2

Coil resistance, Ω (±10%) 22.5 90 202.5 250 360 810 1,440 5,760

3. 2 Coil latching Part No. Standard PC board terminal TX2-L2-1.5 V TX2-L2-3 V TX2-L2-4.5 V TX2-L2-5 V TX2-L2-6 V TX2-L2-9 V TX2-L2-12 V TX2-L2-24 V Notes:

1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.

Nominal operating current, mA (±10%) 133.9 66.7 44.5 40 33.3 22.2 16.7 8.3

Coil resistance, Ω (±10%) 11.2 45 101.2 125 180 405 720 2,880

2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs. 3. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.

TX 2) Surface-mount terminal type 1. Single side stable Part No. TX2S❍-1.5 V TX2S❍-3 V TX2S❍-4.5 V TX2S❍-5 V TX2S❍-6 V TX2S❍-9 V TX2S❍-12 V TX2S❍-24 V TX2S❍-48 V

Nominal voltage, V DC

Pick-up voltage, V DC (max.)

Drop-out voltage, V DC (min.)

1.5 3 4.5 5 6 9 12 24 48

1.13 2.25 3.38 3.75 4.5 6.75 9 18 36

0.15 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8

Nominal voltage, V DC

Set voltage, V DC (max.)

Reset voltage, V DC (max.)

1.5 3 4.5 5 6 9 12 24

1.13 2.25 3.38 3.75 4.5 6.75 9 18

Nominal voltage, V DC 1.5 3 4.5 5 6 9 12 24

Nominal operating current, mA (±10%) 93.8 46.7 31 28.1 23.3 15.5 11.7 5.8 5.6

Coil resistance, Ω (±10%)

Nominal operating power, mW

Max. allowable voltage, V DC

16 64.3 145 178 257 579 1,028 4,114 8,533

140 140 140 140 140 140 140 140 270

2.2 4.5 6.7 7.5 9 13.5 18 36 57.6

Nominal operating current, mA (±10%)

Coil resistance, Ω (±10%)

Nominal operating power, mW

Max. allowable voltage, V DC

1.13 2.25 3.38 3.75 4.5 6.75 9 18

66.7 33.3 22.2 20 16.7 11.1 8.3 4.2

22.5 90 202.5 250 360 810 1,440 5,760

100 100 100 100 100 100 100 100

2.2 4.5 6.7 7.5 9 13.5 18 36

Set voltage, V DC (max.)

Reset voltage, V DC (max.)

Nominal operating current, mA (±10%)

Coil resistance, Ω (±10%)

Nominal operating power, mW

Max. allowable voltage, V DC

1.13 2.25 3.38 3.75 4.5 6.75 9 18

133.9 66.7 44.5 40 33.3 22.2 16.7 8.3

11.2 45 101.2 125 180 405 720 2,880

200 200 200 200 200 200 200 200

2.2 4.5 6.7 7.5 9 13.5 18 36

2. 1 coil latching Part No. TX2S❍-L-1.5 V TX2S❍-L-3 V TX2S❍-L-4.5 V TX2S❍-L-5 V TX2S❍-L-6 V TX2S❍-L-9 V TX2S❍-L-12 V TX2S❍-L-24 V

3. 2 coil latching Part No. TX2S❍-L2-1.5 V TX2S❍-L2-3 V TX2S❍-L2-4.5 V TX2S❍-L2-5 V TX2S❍-L2-6 V TX2S❍-L2-9 V TX2S❍-L2-12 V TX2S❍-L2-24 V

❍: For each surface-mounted terminal variation, input the following letter. SA type: A , SL type: L , SS type: S

Notes: 1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs. 3. Tape and reel packing is also available for surface-mount type by request. Part number suffix "-X" or "-Z" is needed when ordering. In this case, "X" or "Z" are not marked on the relay. Quantity in tape and reel: 500 pcs. • TX2SA-L-3V-Z (ex.) • TX2SA-3V-X Picked from the 1/3/4/5-pin side Picked from the 8/9/10/12-pin side 4. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.

TX DIMENSIONS

mm inch

1. Single side stable and 1 coil latching type 15 Standard PC board terminal .591

PC board pattern (Copper-side view)

7.4 .291

0.65 8.2 .026 .323

0.5 .020 1.15 .045

Self clinching terminal

2.54 .100

3.5 .138 5.08 .200

5.08 .200

2.54 .100

Schematic (Bottom view) Single side stable 1 coil latching (Deenergized condition) (Reset condition)

10.16 .400

0.25 .010

5.08 .200

–

8-1.0 dia 8-.039 dia

15 .591

7.4 .291

3 4 5

10 9 8

– +

Direction indication*

Tolerance: ±0.1 ±.004

3 4 5

10 9 8

Direction indication*

*Orientation stripe located on top of relay.

0.65 8.2 .026 .323

0.5 .020 1.15 .045

3.5 .138 5.08 .200

5.08 .200

2.54 .100

0.25 .010

General tolerance: ±0.3 ±.012

Surface-mount terminal SA type

1 5.08 .039 .200

15 .591

7.4 .291 8.2 .323

0.5 .020 5.08 .200

0.65 2.54 .026 .100

0.5 .020 5.08 .200

SS type

5.08 .200

1 5.08 .039 .200

Max. 10.0 .390 5.08 .200

Self clinching terminal

3 4 5

10 9 8

3 4 5

–

+ Direction indication

Direction indication

2.54 .100

6.24 .246

0.25 .010

7.4±0.5 .291±.020

15 .591

Tolerance: ±0.1 ±.004 PC board pattern (Copper side view)

7.4 .291

12.7 .500

2.54 .100

3.5 .138 5.08 .200

2.54 .100

2.16 .085

0.65 8.2 .026 .323

0.5 .020 1.15 .045

10 9 8

7.24 .285

7.4 .291

0.65 2.54 .026 .100

3.16 .124

General tolerance: ±0.3 ±.012

2. Coil latching type Standard PC board terminal

For glue-pad

15 .591

5.08 0.25 .200 9.4±0.5 .010 .370±.020

8.2 .323 0.5 .020

0.3 .012

1 5.08 .039 .200

Max. 10.0 .390

15 .591

–

7.24 .285

7.4 .291

0.65 2.54 .026 .100

Schematic (Top view) Single side stable 1 coil latching (Deenergized condition) (Reset condition)

1.6 .0.63

3.16 .124

5.08 .200 0.25 9.4±0.5 .010 .370±.020

8.2 .323

2.54 .100

8.4 .331

15 .591

SL type

Suggested mounting pad (Top view)

5.08 .200

2.54 .100

15 .591

5.08 .200

0.25 .010 10-1.0 dia 10-.039 dia

7.4 .291

Schematic (Bottom view) 2 coil latching (Reset condition) 1

3 4 5 6

–

10 9 8 7

Direction indication*

Tolerance: ±0.1 ±.004

0.65 8.2 .026 .323

0.5 .020 1.15 .045

3.5 .138 5.08 .200

5.08 .200

2.54 .100

0.25 .010

General tolerance: ±0.3 ±.012

Surface-mount terminal SA type

Suggested mounting pad (Top view) 15 .591 8.2 .323 0.5 .020 5.08 .200

5.08 .200 0.25 9.4±0.5 .010 .370±.020

0.65 2.54 .026 .100

0.5 .020 5.08 .200

SS type

0.65 2.54 .026 .100

For glue-pad

2.54 .100

3.16 .124 7.24 .285

7.4 .291 8.2 .323

5.08 .200

15 .591

5.08 0.25 .200 9.4±0.5 .010 .370±.020

0.65 2.54 .026 .100

1 5.08 .039 .200

Max. 10.0 .390

2.54 .100

2.16 .085 5.08 .200

6.24 .285 0.25 .010

7.4±0.5 .291±.020

General tolerance: ±0.3 ±.012

Schematic (Top view) 2 coil latching (Reset condition) 12

Tolerance: ±0.1 ±.004

10 9 8

+ + 1

0.3 .012 1 5.08 .039 .200

Max. 10.0 .390

15 .591

0.5 .020

1.6 .0.63 7.24 .285

7.4 .291 8.2 .323

2.54 .100

3.16 .124

8.4 .331

15 .591

SL type

1 5.08 .039 .200

7.4 .291

– – 3

4 5

Direction indication

TX REFERENCE DATA 1. Maximum switching capacity

2. Life curve

3. Mechanical life

Ratio against the rated voltage, %V

Tested sample: TX2-5V, 10 pcs. Operating frequency: 180 cpm 3.0 100 No. of operations ×104

Switching current, A

2.0 DC resistive load

1.0

0.5 0.4 0.3

50 30V DC resistive load

30 20 10

0.2

100 90 80

Pick-up voltage

Max.

Min.

50 40 30

Drop-out voltage

Max. Min.

10 0

20 30

50 100 200 300 Contact voltage, V

1.0 2.0 Switching current, A

100 1,000 No. of operations, ×104

10,000

4. Electrical life

5-(1). Coil temperature rise

Tested sample: TX2-5V, 6 pcs. Operating frequency: 20 cpm

Tested sample: TX2-5V, 6 pcs. Point measured: Inside the coil Ambient temperature: 25°C 77°F, 85°C 185°F

Change of contact resistance 100

Pick-up voltage

Max.

Min.

50 40

Drop-out voltage

Max.

30 20

80 70 60 50 40

Max.

Min.

+25°C +77°F +85°C +185°F

60 50 40 30

2A 2A

0A 0A

20 Min.

4 5 6 7 8 9 No. of operations, ×104

10 0

4 5 6 7 8 9 4 No. of operations, ×10

5-(2). Coil temperature rise

6-(1). Operate and release time (with diode)

Tested sample: TX2-48V, 6 pcs. Point measured: Inside the coil Ambient temperature: 25°C 77°F, 70°C 158°F

Tested sample: TX2-5V, 10 pcs.

+25°C +77°F +70°C +158°F

60 50

2A 0A

Max.

Min.

Max. Min.

100 110 120 130 140 150 No. of operations, ×104

120 130 140 150 No. of operate, ×104

5 Operate time Release time

100 110

6-(2). Operate and release time (without diode)

5 Operate and release time, ms

Operate and release time, ms

Temperature rise, °C

100

Contact resistance, mΩ

Ratio against the rated voltage, %V

Change of pick-up and drop-out voltage

Operate time Release time

Max. Min.

2 Max. Min. 1

90 100 110 120 Coil applied voltage, %V

8. Distribution of set and reset voltage

9. Ambient temperature characteristics

Tested sample: TX2-5V, 50 pcs.

Tested sample: TX2-L2-12V, 30 pcs.

Tested sample: TX2-5V, 5 pcs.

10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V

Rate of change, %

Quantity

Drop-out voltage 20

Set voltage Reset voltage

Pick-up voltage

;;;;;;; ;;;;;;

Quantity

; ; ; ; ;;;;;;;;;; ;;;;;

7. Distribution of pick-up and drop-out voltage

10 –40 –20 5

Pick-up voltage 20 40 60 80 Ambient temperature, °C –20

–40 0

10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V

Drop-out voltage x x

TX 10. Distribution of contact resistance

11-(1). High frequency characteristics

11-(2). High frequency characteristics

Tested sample: TX2-5V, 30 pcs. (30 × 4 contacts)

Tested sample: TX2-12V, 2 pcs. Isolation characteristics

Tested sample: TX2-12V, 2 pcs. Insertion loss characteristics

3 4 5

10 9 8

15 10 5

0 20

Terminal Nos. 3-4, 9-10

100

0.4 0.2 10

30 40 50 Contact resistance, mΩ

100 Frequency, MHz

1,000

12-(2). Malfunctional shock (latching)

Tested sample: TX2-5V, 6 pcs

Tested sample: TX2-L2-12V, 6 pcs.

Z XX'

Y 1000m/s 2

Deenergized condition Energized condition

Z' Y Y'

Z XX'

X 1000m/s2

Z 1000m/s2

1000m/s 2 Z'

1000m/s2 X'

1000m/s 2 Z'

1000m/s2 X'

0 –5

OFF OFF Drop-out voltage

–5

OFF 2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance

1,000

13-(3). Influence of adjacent mounting

Rate of change, %

Rate of change, % Rate of change, %

13-(2). Influence of adjacent mounting

Pick-up voltage

100 Frequency, MHz

1000m/s 2 Y'

13-(1). Influence of adjacent mounting

Reset state Set state

Z 1000m/s2

1000m/s 2 Y'

Y 1000m/s 2

X 1000m/s2

0.8 0.6

12-(1). Malfunctional shock (single side stable)

Z' Y Y'

1.0

5 Pick-up voltage 0

–5

Rate of change, %

Insertion loss, dB

(BOTTOM VIEW) Isolation, dB

Quantity

;;;;;;; ; ;;;;;;;;;

;;;;;;;;;; ; ;;;;;;;;

35 Terminal Nos. 4-5, 8-9

OFF

5 Drop-out voltage 0

OFF –5 OFF 0

, mm inch

2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance

5 Pick-up voltage

–5

ON ON

5 0

OFF Drop-out voltage OFF

–5

OFF OFF 0

, mm inch

2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance

, mm inch

14. Pulse dialing test

Circuit

458 Ω

0.08 µF 48V DC

–

0.08 µF

458 Ω Wire spring relay

4 3

Ratio against the rated voltage, %V

Change of pick-up and drop-out voltage

Change of contact resistance 100

100

90 80

Pick-up voltage

Max. Min.

60 50 40 Drop-out voltage

30 20

Contact resistance, mΩ

Tested sample: TX2-5V, 6 pcs. (35 mA 48 V DC wire spring relay load)

Max. Min.

70 60 50

Max.

40 Min.

30 20 10

10 0

20 30 40 4 No. of operation, ×10

Note: Data of surface-mount type are the same as those of PC board terminal type.

20 30 40 No. of operations, ×104

TX Notes 1. Packing style 1) The relay is packed in a tube with the relay orientation mark on the left side, as shown in the figure below.

2) Tape and reel packing (surface-mount terminal type) (1) Tape dimensions (i) SA type

(2) Dimensions of plastic reel mm inch 21 ±0.6 dia. .827 ±.024 dia.

mm inch 2.0 ±0.5 .079 ±.020

Orientation (indicates PIN No.1)stripe +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079

1.75 .069

4.0 .157

0.4 .016

100 ±1 dia. 3.937 ±.039 dia.

C A

Stopper (gray)

Stopper (green)

11.5 .453

D 16.0 10.0 .394 .630

TX/TX-D/TX-S -SMD relays

15.5 .610

24.0 ±0.3 ±0.2 .945 ±.012 9.2±.008 .362

Tape coming out direction

(ii) SL type mm inch +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079

1.75 .069

4.0 .157

0.4 .016

11.5 .453 15.5 .610

TX/TX-D/TX-S -SMD relays

16.0 .630

10.0 .394 Tape coming out direction

24.0 ±0.3 .945 ±.012

10.8±0.2 .425±.008

(iii) SS type mm inch +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079

2.2 dia. .087 dia. 4.0 1.75 .157 .069

0.4 .016

11.5 .453 15.5 .610

TX/TX-D/TX-S -SMD relays

16.0 .630 Tape coming out direction

8.0 24.0 ±0.3 ±.012 .315 .945 10.8±0.2 .425±.008

For Cautions for Use, see Relay Technical Information.

370 ±2 dia. 14.567 ±.079 dia. ±0.5

13 dia. .512 ±.020 dia. 24.4+20 .961+.079 0

2.0±0.2 .079±.008