Quality is our Strength
WORDS FROM THE PRESIDENT
Alliance prides itself for its quality products
2
Dear Friends, At Alliance Designer Products, our goal is to offer the industry reliable service, innovation and the absolute best quality products on the market. This philosophy allows us to build and maintain long-term relationships and we are proud to consider our customers as being part of our extended family. Our first steps into the hardscape industry have made long lasting impressions culminating in building a business with unique quality products. Our family of products include Polymeric Sands and Dust, Sealers and Cleaners, Edging restraints, Glues and more. All our Polymeric Sands and Dust are available in a variety of distinct colors that will definitely enhance the look of your hardscape project. Furthermore, we are proud to be the only company to offer a 10-year limited warranty on all of our Polymeric Sand and Dust products. Finally our new Water base Natural look Sealer will also carry a 10 year limited warranty towards protecting your hardscape investment. Since 2003, we have established ourselves as more than just a manufacturer of Polymeric Sands. We are committed to developing products that cater to and service the hardscape industry and in several cases our product innovations were the first in the world. We remain focused and determined to continue to invest in research and development in order to meet the challenges of the future. I invite you to go through this catalogue, it will help you to choose the right product for your project. We also invite you to visit our website at AllianceGator.com. Finally, on behalf of the Alliance Designer Products Inc., I would like to sincerely thank our existing customers for their continued support and we cherish the opportunity to serve new customers. Wishing you all the best in the coming year,
George Tutino Owner and President
GATOR POLYMERIC SANDS, GATOR DUST & GATOR AQUA ROCK
GATOR CLEAN Shampoo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17 Rubber, Paint & Tar Remover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Efflorescence Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rust Remover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Oil & Grease Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TABLE
Gator Supersand Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Gator XP Sand Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Gator Maxx Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Eurostone Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 Gator Dust Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13 Gator Aqua Rock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
GATOR SEAL 22-23 . . 24 . . 25 . . 26
Gator Edge Maxi & Mini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Gator Edge Rigid & Flex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
GATOR BLOCK BOND Polyurethane Xtra Strength Adhesive . . . . . . . . . . . . . . . . . . . . . 30-31 High Strength Adhesive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Low VOC High Strength Adhesive . . . . . . . . . . . . . . . . . . . . . . . . . . 33
INSTALLATION GUIDE Gator Supersand Bond & Gator XP Sand Bond . . . . . . . . . . . . . . . . Gator Maxx Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Eurostone Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gator Dust Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34-35 36-37 38-39 40-41
ADVANTAGES
CONTENTS
GATOR EDGE
OF
Natural Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Satin Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wet Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alliance Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3
SEE INSTALLATION INSTRUCTIONS P.34-35
Strength & Durability.
For more details see page 42
For more details see page 43
Polymeric Sand
For concrete paver, wetcast & natural stone joints up to 1” IDEAL FOR: Sloping areas • Pool surroundings • Patios • Walkways • Driveways COLORS AVAILABLE FEATURES
BEIGE
• Sets at above freezing temperature (0° C – 32° F).
SLATE GREY
• Fast setting. Can be applied even if rain is expected (minimum 1 hour after sand installation).
IVORY
• Intact pallets can be stored outside. • Alerts you when to stop watering during installation
SEE INSTALLATION VIDEO ON ALLIANCEGATOR.COM
DOES NOT HAZE PAVING STONES Weed sprouting.
Damages caused by insects.
Erosion due to climatic conditions, such as wind, rain and freezing.
APPLICATIONS
• Can be used for paver joints up to a maximum of 1”.
HELPS PREVENT
RESIDENTIAL
GATOR SUPERSAND BOND
A D V A N T A G E S
POLYMERIC SAND
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
5
SEE INSTALLATION INSTRUCTIONS P.34-35
High TrafямБc & Commercial Applications.
For more details see page 42
For more details see page 43
Polymeric Sand
For concrete paver, wetcast & natural stone joints up to 1.5” IDEAL FOR: Sloping areas • Pool surroundings • Patios • Walkways • Driveways • Street • High traffic areas • Parking lot COLORS AVAILABLE FEATURES
BEIGE
• Sets at above freezing temperature (0° C – 32° F).
SLATE GREY
• Fast setting. Can be applied even if rain is expected (minimum 1 hour after sand installation).
IVORY
• Resists the brooming and suction from the mechanical street cleaner. • Intact pallets can be stored outside. • Xtra Bonding
SEE INSTALLATION VIDEO ON ALLIANCEGATOR.COM
• Xtra Durability • Xtra Resistant
DOES NOT HAZE PAVING STONES Weed sprouting.
Damages caused by insects.
Erosion due to climatic conditions, such as wind, rain and freezing.
APPLICATIONS
• Can be used for paver joints up to a maximum of 1.5”.
HELPS PREVENT
COMMERCIAL
GATOR XP SAND BOND
A D V A N T A G E S
POLYMERIC SAND
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
7
SEE INSTALLATION INSTRUCTIONS P.36-37
Anytime. Anyplace. And Now Any Surface.
DRAINAGE BASE
1hr
SETTING TIME
NON-DRAINAGE BASE SETTING TIME
24 hrs
32
°F
SETS ABOVE FREEZING TEMP. (32°F / 0°C)
For more details see page 42
Polymeric Sand
For concrete paver, wetcast & natural stone joints up to 1” Overlays • Sloping areas • Pool surroundings • Patios • Walkways • Driveways
COLORS AVAILABLE
FEATURES • Can be used for paver joints up to a maximum of 1 inch. • Sets at above freezing temperature (0° C – 32° F). • Fast setting. For Drainage base systems. A minimum of 1 hour without rain is needed after installation. • For Non-drainage base systems. A minimum of 24 hours without rain is needed after installation. • Intact pallets can be stored outside.
BEIGE
SLATE GREY IVORY
SEE INSTALLATION VIDEO ON ALLIANCEGATOR.COM
DOES NOT HAZE CONCRETE PAVING STONES
HELPS PREVENT
Weed sprouting.
Damages caused by insects.
Erosion due to climatic conditions, such as wind, rain and freezing.
FOR RESIDENTIAL AND COMMERCIAL APPLICATIONS
IDEAL FOR:
O V E R L AYS /
GATOR MAXX BOND
A D V A N T A G E S
POLYMERIC SAND
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
9
Harrinman, NY USA
Milan, Italy
Vermicelli, Italy SEE INSTALLATION INSTRUCTIONS P.38-39
From Europe to America.
NON-DRAINAGE BASE SETTING TIME
24 hrs
32
°F
SETS ABOVE FREEZING TEMP.
(32°F / 0°C)
For more details see page 42
Polymeric Sand
For natural stone & cobblestone joints up to 1.5” IDEAL FOR: Plaza, street (Pedestrian and vehicular traffic) • Paths • Paved sloping areas • Driveway aprons • Pool surroundings etc... COLORS AVAILABLE FEATURES
BEIGE
• Can be used for stone joints up to a maximum of 1.5” (3.75 cm). • Sets at above freezing temperature (0° C – 32° F).
SLATE GREY
• Stabilizes the natural stones. • Resists the brooming and suction from mechanical street cleaner.
IVORY
• Used for drainage and non-drainage base systems. • Intact pallets can be stored outside.
NATURAL STONE APPLICATIONS
EURO STONE BOND
A D V A N T A G E S
POLYMERIC SAND
DOES NOT HAZE NATURAL STONES
HELPS PREVENT
Weed sprouting.
Damages caused by insects.
Erosion due to climatic conditions, such as wind, rain and freezing.
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
11
SEE INSTALLATION INSTRUCTIONS P.40-41
Mason’s Craftmanship Simplified.
For more details see page 42
Polymeric Stone Dust For stone joints 1/2” to 4”
IDEAL FOR:
Patios • Walkways • Pool Decks
COLORS AVAILABLE
FEATURES
SAHARA BEIGE
• Must be installed at above temperature 59°F (15°C). • Compatible with all types of stones. • For stone joints of 1/2“ to 4” wide. • Can only be installed if rain is not forecasted within the next 24 hours. • Intact pallets can be stored outside. • Individual bags must be kept in dry storage. • For pedestrian application only.
STONE GREY
SEE INSTALLATION VIDEO ON ALLIANCEGATOR.COM
FOR STONE JOINTS 1/2” TO 4”
GATOR DUST BOND
A D V A N T A G E S
POLYMERIC STONE DUST
DOES NOT HAZE STONES
HELPS PREVENT
Weed sprouting.
Damages caused by insects.
Erosion due to climatic conditions, such as wind, rain and freezing.
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
13
Long-Term High InďŹ ltration Performance.
Permeable Stone
For permeable paver joints (ASTM No.9 Granite Stone) IDEAL FOR: Drainage applications • Bedding and jointing material • Residential & Commercial applications FEATURES • Superior stabilization. • Calibrated for the majority of the permeable pavers. • High strength granite stone. • Helps prevent erosion. • Reduction of storm water rate. • Long-term high infiltration performance.
ASTM No.9 Sieve size 3/8in. (9.5mm) No.4 (4,75mm) No.8 (2,36mm) No. 16 (1,18mm) No. 50 (0.300mm)
COLORS AVAILABLE GRANITE GREY
ASTM No.9 100 85 to 100 10 to 40 0 to 10 0 to 5
F O R P E R M E A B L E PAV E R S
GATOR AQUA ROCK
PERMEABLE STONE
Helps prevent erosion due to climatic conditions, such as wind, rain and freezing. F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
15
Reclaim Your Investment.
CLEANER
Shampoo
For concrete pavers & natural stones
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
1 US GAL. / 3.78 L.
FEATURES
• Removes penetrated dirt • Will restore your pavers to their natural color • Does not contain muriatic acid • Will not affect plantation
BEFORE
DESCRIPTION
SHAMPOO
5 US GAL. / 18.9 L.
Gator Clean Shampoo removes ground in dirt from the surface of concrete pavers and natural stones. It will make the pavers, patio slabs, walls & natural stones look clean and vibrant. Applying Gator Clean Shampoo before a sealer application will assure you of a deeper penetration into the cleaned surface.
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
17
CLEANER
Rubber, Paint & Tar
R U B B E R , PA I N T & TA R
For concrete pavers & natural stones
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
1 QT. / 946 ml.
FEATURES
• Easy to use • Washes off with water
RUBBER
DESCRIPTION
Gator Clean Rubber, Paint and Tar Remover is effective in removing rubber, paint and tar from the surface of concrete pavers and natural stones.
PAINT
TAR
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
18
CLEANER
Efflorescence Cleaner For concrete pavers & natural stones
5 US GAL. / 18.9 L.
1 US GAL. / 3.78 L.
FEATURES
• Dislodges efflorescence and encrusted dirt from the surface of concrete pavers and natural stones • Recommended prior to sealant application • Does not contain muriatic acid
BEFORE
DESCRIPTION
Gator Clean Efflorescence Cleaner eliminates the spots caused by efflorescence caught in the concrete pavers and natural stone pores. It will make the pavers look cleaner and more vibrant. The efflorescence cleaning is a necessary step before a sealer is applied. Cleaning will permit a better penetration into the pores when sealing.
EFFLORESCENCE
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
19
CLEANER
Rust Remover
For concrete pavers & natural stones
RUST
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
1 QT. / 946 ML.
FEATURES
• Removes the spots caused by steel, water build up, fertilizer, etc. • Contains no muriatic acid • Easy to use
BEFORE
DESCRIPTION
Gator Clean Rust Cleaner is effective in removing rust on the surface of concrete pavers and natural stones.
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
20
CLEANER
Oil & Grease Cleaner For concrete pavers & natural stones
1 QT. / 946 ML.
FEATURES
• Dissolves, dislodges and removes oil and grease • Easy to use
BEFORE
DESCRIPTION
Gator Clean Oil and Grease Cleaner is effective in removing oil and grease on the surface of concrete pavers.
OIL & GREASE
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
21
Protect Your Investment.
SEALER
Natural Look
For concrete pavers & walls, masonry & natural stones
5 US GAL. / 18.9 L.
FEATURES • • • •
Non film forming Non slip formula Easy to clean & maintain Applicable on damp surfaces
1 US GAL. / 3.78 L.
HELPS RESIST • • • •
De-icing salt Ultraviolet rays Motor oil and grease Stains up to 10 years
DESCRIPTION
Gator Seal is made from fluorochemical polymers. This sealer penetrates deep into the concrete pavers & walls, masonry and natural stones, thus reducing the oil and dirt penetration, as well as protecting them from de-icing salt.
N AT U R A L L O O K
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
Gator Natural Look Sealer is made from an advanced high-tech patented formula called Gator Stone Guard. This breathable long lasting sealer deeply penetrates into the concrete & stone pores providing an invisible & durable shield that will protect your hardscape investment for up to 10 years.
Clear, Transparent, Invisible Protection
PAVERS
RETAINING WALLS
MASONRY
NATURAL STONES
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
23
SEALER
Satin Look
For concrete pavers & natural stones
S AT I N L O O K
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
5 US GAL. / 18.9 L.
1 US GAL. / 3.78 L.
FEATURES • • • • •
HELPS RESIST
Low gloss matte finish Solvent based Easy to clean and maintain Non slip formula Maintains natural look
• De-icing salt • Ultraviolet rays • Motor oil and grease
DESCRIPTION
Gator Seal Satin Look Sealer is made from acrylic based polymers. Gator Seal Satin Look Sealer penetrates deep into the concrete paver and natural stone pores, thus reducing the oil and dirt penetration, as well as protecting them from de-icing salt.
LOW GLOSS MATTE FINISH
BEFORE
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
24
SEALER
Wet Look
For concrete pavers & natural stones
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
1 US GAL. / 3.78 L.
FEATURES • • • • •
High gloss lustrous finish Solvent based Easy to clean and maintain Non slip formula Pavers look more vibrant
HELPS RESIST • De-icing salt • Ultraviolet rays • Motor oil and grease
DESCRIPTION
WET LOOK
5 US GAL. / 18.9 L.
Gator Seal Wet Look Sealer is made from acrylic based polymers. Gator Seal Wet Look Sealer penetrates deep into the concrete paver and natural stone pores, thus reducing the oil and dirt penetration, as well as protecting them from de-icing salt.
HIGH GLOSS LUSTROUS FINISH
BEFORE
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
25
SEALER
Resealer
For concrete pavers & natural stones
RESEALER
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
5 US GAL. / 18.9 L.
1 US GAL. / 3.78 L.
FEATURES • • • • • •
HELPS RESIST
Revives look Solvent based Easy to clean and maintain Non slip formula Makes pavers look more vibrant Can be applied to Gator Satin Look and Wet Look finishes
• De-icing salt • Ultraviolet rays • Motor oil and grease
DESCRIPTION
Gator Seal Resealer for concrete pavers and natural stones is made from acrylic based polymers. Gator Seal Resealer will penetrate the formula of the existing sealer & reactivate the molecules to create a rejuvenated seal to protect the paver surface. Thus reducing the oil and dirt penetration, as well as protecting them from de-icing salt.
REJUVENATES SURFACE
BEFORE
AFTER
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
26
EDGE
G AT O R E D G E The ďŹ nal touch... with the right support. 27
G AT O R E D G E M A X I & M I N I
EDGE
Maxi & Mini SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
1.75”
1”
FEATURES • • • • • • •
Will not corrode Easy-to-use Edge Maxi 1.75” profile Edge Mini 1” profile Economically priced for a high quality product Comes in 8-ft lengths Use with Gator Nails
DESCRIPTION
Gator Edge Maxi & Mini are made with 100 % Polyethylene. This will give it greater strength as well as provide good flexibility for pavers, natural stone and all types of slabs. It is easy to use and quick to install. We have a Gator Edge Maxi model which is ideal for applications of 1.75”, and a Gator Edge Mini model for applications of 1” that can be used for natural stone, concrete and clay pavers and all type of slabs in walkways, patios, paths etc.
Gator Nails
10”, 12” bright common or spiral metal nails used with Gator Edges.
Packaging
• 190 nails /10” common per box • 48 boxes per pallet F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
28
EDGE
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
DESCRIPTION
FEATURES • • • • • • • • • •
Gator Edge is made with 100% Polypropylene Co-Polymer. This will give it great strength as well as providing greater flexibility. We have a Rigid model which is ideal for straight applications and have a Flex model that can be used for all curved applications such as walkways, paths, entrances etc. Both the Rigid and Flex can be locked together with the ‘’Twist & Lock’’ connection system.
The Flex can connect to the Rigid Uses a “Twist & Lock” connection system Will not corrode Easy-to-use Available in flexible or rigid edges Comes in 8-ft lengths Use with Gator Nails Xtra versatile Xtra robust system Xtra support strength
STRONG LATERAL SUPPORT
A triangular angle at all key points has been engineered to provide a strong lateral support, essential for the load transfer on the paving units. Rigid can be modified into a Flex by simply cutting the connector between each triangular angle.
Gator Nails
G AT O R E D G E R I G I D & F L E X
Rigid & Flex
10”, 12” bright common or spiral metal nails used with Gator Edges.
Packaging
• 190 nails /10” common per box • 48 boxes per pallet F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
29
Be safe... the best adhesives for the right applications.
ADHESIVES
Polyurethane Adhesive
For bonding concrete, natural stones, blocks, bricks & pavers ZERO
VOC WORKS ABOVE
32°F
BOND STRENGTH
DURABILITY
PERMANENT BOND
24 HRS 28 fl. oz. / 828 ml.
FORMULATED FOR • Overlays & pool copings • Steps & wall caps • Fire pits (up to 400°F) • Concrete pavers & stones • Dry & damp surfaces • Permanent bond in 24 hrs
10 fl. oz. / 296 ml.
DESCRIPTION
Gator Block Bond Xtra Strength Polyurethane Adhesive is one of the strongest polyurethane adhesives on the market. It is especially formulated for bonding concrete, natural stones, blocks, bricks and pavers. Gator Block Bond Xtra performance Polyurethane Concrete Adhesive is formulated to provide a permanent bond to the above materials if properly installed.
SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
XTRA STRENGTH
FAST CURE TIME
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
31
ADHESIVES
High Strength Adhesive
For bonding concrete, natural stones, blocks, bricks & pavers
HIGH STRENGTH
WORKS ABOVE
32°F SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
High Strength NOT available in the states of: CA, IL, MA, NJ, PA,DC, CT, IN, ME, NY, RI, WI, MI, DE, MD,OH and VA.
28 fl. oz. / 828 ml.
10 fl. oz. / 296 ml.
DESCRIPTION
Gator Block Bond High Strength Adhesive is especially formulated for bonding concrete, natural stones, blocks, bricks and pavers.
FORMULATED FOR • Retaining walls • Masonry units • Stones & bricks • Concrete pavers • Dry & damp surfaces • High strength & durability
GATOR BLOCK BOND ADHESIVE APPLICATIONS Works above 32 degrees Fahrenheit Concrete Pavers & Bricks Dry & Damp Surfaces Retaining Walls Masonry Units Stones High Strength & Durability VOC Compliant Permanent Bond in 24 hours Xtra Fast Cure Time Xtra Bond Strength Xtra Durability Overlays & Pool coping Steps & Wall caps Fire Pits (up to 400°F)
Gator Block Bond
Gator Block Bond
Gator Block Bond
XTRA STRENGTH
HIGH STRENGTH - LOW VOC
HIGH STRENGTH
X X X X X X X X X X X X X X X
X X X X X X X X
X X X X X X X
polyurethane adhesive
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
32
32
ADHESIVES
For bonding concrete, natural stones, blocks, bricks & pavers LOW
VOC SEE APPLICATION VIDEO ON ALLIANCEGATOR.COM
WORKS ABOVE
32°F 28 fl. oz. / 828 ml.
FORMULATED FOR • Retaining walls • Masonry units • Stones & bricks • Concrete pavers • Dry & damp surfaces • High strength & durability
10 fl. oz. / 296 ml.
DESCRIPTION
Gator Block Bond High Strength Low VOC Adhesive is especially formulated for bonding concrete, natural stones, blocks, bricks and pavers.
HIGH STRENGTH / LOW VOC
High Strength Low VOC Adhesive
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
33
33
INSTALLATION
Installation
Gator Super Sand & Gator XP Sand
I N S TA L L AT I O N
STEP 1A
STEP 1B
STEP 2
STEP 3
FOR A NEW PAVER JOB: STEP 1 STEP 2
STEP 3 STEP 4 STEP 5 STEP 6 STEP 7
Use a concrete sand as your bedding course to do the final leveling. (Step 1-A). Install the concrete pavers or slabs. (Step 1-B). After the paver surface has been installed, it should be compacted using a vibrating-plate compactor, with a 5,000 lb (22 kN) centrifugal compaction force. We recommend using a mat fastened to the vibrating plate when compacting the pavers in order to avoid damaging them. The whole paver surface area should be compacted at least twice so that all pavers sit firmly into the bedding sand. Make sure the pavers’ side and top surfaces are dry before applying the polymeric sand. Spread GATOR SAND over the pavers, then use a hard-bristle brush to sweep the sand into the joints and fill them completely. Run a vibrating plate-compactor over the pavers in several directions to compact the sand inside the joints (this action is not appropriate for slabs). Repeat this step (spreading the sand, sweeping it into the joints, then compacting) at least twice. If a vibrating-plate compactor cannot be used, tamp the stones with a rubber mallet and make sure the GATOR SAND is densely packed in the joints. Using a fine-bristle broom, remove any excess sand from paver surfaces. Make sure the finished sand level is at least 1/8 in (3mm). lower than the surface of the pavers. Using a leaf blower, remove any sand residue from paved surfaces. Depending on the physical layout, it may be more appropriate to remove residue by using a vacuum unit. At a height of 4 feet (1.2m), use a water gun connected to a hose to direct a fine mist (water gun setting: “mist” or equivalent) of water on a specific paved area for 10 to 15 seconds. Wait 3 to 4 minutes (not longer). Proceed to STEP 5. From a height of 2 feet ( .60m), aim the water mist directly at the paved surface. Mist and rinse simultaneously so as to eliminate any GATOR SAND residue left on the pavers. Any GATOR SAND residue should go directly into the paver joints. Wait 3 to 4 minutes (not longer). Proceed to STEP 6. (Photo 5). From a height of 2 feet ( .60m), aim the water mist again directly at the paved surface. Again, mist and rinse simultaneously so as to eliminate any GATOR SAND residue left on the pavers. The GATOR SAND residue should go directly into the paver joints. However, stop misting (ALERT) when you see a minimal amount of water retention on the paver joints. NOTE : Repeat the directions of steps 4 to 6 for all other areas that have not been misted with water. Use a leaf blower to remove any excess surface water lying on paver pores and crevices. This blowing action is necessary to help remove any remaining GATOR SAND residue that was left on paver surfaces from the previous steps.
IMPORTANT
The water used in steps 4, 5 & 6 will activate a bonding action as well as condense GATOR SAND in the joints. Too much water will undo the dense compaction obtained during step 2 and reduce the final performance of GATOR SAND. If steps 4 to 7 are not done properly, a white haze may appear on paver surfaces after installation. This is due to excess GATOR SAND residue left on paver surfaces. This haze will dissipate over time. It can also be removed by using a concrete efflorescence cleaner.
FOR AN EXISTING PAVER JOB:
Follow the same installation procedure as with a new paved surface. Ensure that all the existing sand between the joints has been completely removed before applying GATOR SAND. A pressure washer is often needed to remove all the joint filling material. However, be careful not to disturb the bedding material under the pavers.
34
INSTALLATION
STEP 4
STEP 5
STEP 6
STEP 7
Do not apply on wet or damp surface since bonding action will cause GATOR SAND to stick on surface and avoid proper sliding in joint. Do not use if rain is expected within 1 hour. Avoid excessive watering or flooding of paved surfaces. When installing pavers around an underground pool a slope of 1/8 inch (3 mm) per linear foot away from the pool is mandatory. All paver surfaces must have a drainage slope for the GATOR SAND to work at its optimum. For the pool coping blocks it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use GATOR SAND. Do not sweep GATOR SAND over asphalt.
For use on and required sub-surface preparation
GATOR SAND is recommended for a variety of uses, including pool sides, patios, foot paths, driveways, parking spaces, pavements etc. The concrete pavers must be installed on a drainage base system composed of 2 layers. The upper layer can have a maximum of 1 inch (2.5 cm) of bedding sand. The lower layer must have a minimum of 5� (12.5 cm) of crushed stone, compacted at 95% of the Proctor density. See diagram below.
OK OK PAVER PAVER
GATOR GATOR SAND SAND BEDDING SAND BEDDING SAND
maximum of 1ofinch (2.5(2.5 cm)cm) maximum 1 inch
CRUSHED STONE CRUSHED STONE
minimum of 5ofinches (12.5 cm)cm) minimum 5 inches (12.5
JOINT FILLED PROPERLY JOINT FILLED PROPERLY (JOINT IS COMPLETELY FILLED WITH POLYMERIC SAND) (JOINT IS COMPLETELY FILLED WITH POLYMERIC SAND)
GATOR SAND GATOR SAND PAVER PAVER PAVEROTHER PAVER PRODUCT OTHER PRODUCT DRAINAGE BED DRAINAGE BED
DRAINAGE BED DRAINAGE BED
PAVER PAVER
NOT NOTOK OK
I N S TA L L AT I O N
Please Note
BEDDING SAND BEDDING SAND
maximum of 1ofinch (2.5(2.5 cm)cm) maximum 1 inch
CRUSHED STONE CRUSHED STONE
minimum of 5ofinches (12.5 cm)cm) minimum 5 inches (12.5
JOINT NOTNOT FILLED PROPERLY JOINT FILLED PROPERLY (JOINT DILUTED WITH OTHER PRODUCT) (JOINT DILUTED WITH OTHER PRODUCT)
Coverage
Quantity required depends on the shape and size of paving area, the concrete pavers as well as the width of the joints.
For 50 lb ( 22.7 Kg ) bag Narrow Joints Wide Joints
65 to 85 ft2 ( 6 to 7.4 m2 ) 22 to 42 ft2 ( 2 to 3.9 m2 )
35
INSTALLATION
Installation Gator Maxx Sand
I N S TA L L AT I O N
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
FOR A NEW PAVER JOB: BEFORE STEP 1 STEP 2
Diagrams 1 & 4 (on page 37) describe the sub base for the installation steps below. Remove all loose and fragile concrete. After excavating, cover the ground with a geotextile, refill with crushed stone, (minimum 5 inches (12.7 cm)) and compact it. Make sure that the geotextile will be wide enough to go up against the paver edge restraint, this will prevent the migration of the bedding sand. On the slab section, prepare a minimum 12’’ (30.5 cm) wide geotextile strip. This should be wide enough to go up against the paver edge restraint, thus prevent the migration of the bedding sand. STEP 3 Install the paver edge restraint where needed. Then install the bedding sand (concrete sand) for proper leveling, (maximum 1” (2.5 cm)). Assure that the pavers or slabs will be flush with city sidewalk. Respect a minimum 1 degree slope for proper water run off from the paved surface. STEP 4 Install the concrete pavers or slabs. STEP 5 First, compact the paved area with a vibrating plate compactor, with a 5000 lbs (22kN) centrifugal compaction force. We recommend using a mat fastened to the vibrating plate to compact the pavers. At least two passes are required across the pavers to sit them in the bedding sand. Second, make sure that the pavers’ side and top surfaces are dry before applying the polymeric sand. Spread GATOR MAXX SAND over the pavers then use a hard-bristle brush to sweep the sand into the joints and filling them completely. Run a vibrating plate over the pavers in several directions to compact the sand inside the joints (this action is not appropriate for slabs). Repeat this step (spreading the sand, then compacting) at least two more times. If a vibrating plate compactor cannot be used, tamp the stones with a rubber mallet and make sure the GATOR MAXX SAND is densely packed in the joints. STEP 6 Using a fine-bristle broom, remove any excess from paver surfaces. Make sure the finished sand level is at least 1/8 in. lower than the surface of the pavers. Using a leaf blower, remove any sand residue from paved surfaces. Depending on the physical layout, it may be more appropriate to remove residue by using a vacuum unit. STEP 7 At a height of 4 feet (1.2m), use a water gun connected to a hose to direct a fine mist (water gun setting: “mist” or equivalent) of water on a specific paved area for 10 to 15 seconds. Wait 3 to 4 minutes (not longer). Proceed to STEP 8. STEP 8 From a height of 2 feet (.60m), aim the water mist directly at the paved surface. Mist and rinse simultaneously so as to eliminate any GATOR MAXX SAND residue left on the pavers. Any GATOR MAXX SAND residue should go directly into the paver joints. Wait 3 to 4 minutes (not longer). Proceed to STEP 9. STEP 9 From a height of 2 feet (.60m), aim the water mist again directly at the paved surface. Again, mist and rinse simultaneously so as to eliminate any GATOR MAXX SAND residue left on the pavers. The GATOR MAXX SAND residue should go directly into the paver joints. However, stop misting (ALERT) when you see a minimal amount of water retention on the paver joints. NOTE : Repeat the directions of steps 7 to 9 for all other areas that have not been misted with water. STEP 10 Use a leaf blower to remove any excess water lying on paver pores and crevices. This blowing action is necessary to help remove any remaining GATOR MAXX SAND residue that was left on the paver surface from the previous steps.
IMPORTANT
The water used in steps 7, 8 & 9 will activate a bonding action as well as condense GATOR MAXX SAND in the joints. Too much water will undo the dense compaction obtained during step 5 and reduce the final performance of GATOR MAXX SAND. If steps 6 to 10 are not done properly, a white haze may appear on the paver surface after installation. This is due to excess GATOR MAXX SAND residue left on the paver surface. This haze will dissipate over time. It can also be removed by using a concrete efflorescence cleaner.
36
INSTALLATION
Installation Gator Maxx Sand STEP 8
STEP 7
STEP 6
STEP 10
STEP 9
Follow the same installation procedure as with a new paved surface. Ensure that all the existing sand between the joints has been completely removed before applying GATOR MAXX SAND. A pressure washer is often needed to remove all the joint filling material. However, be careful not to disturb the bedding material under the pavers.
PLEASE NOTE
Do not apply on wet or damp surface since bonding action will cause Gator Maxx Sand to stick on surface and avoid proper sliding in joint. Avoid excessive watering or flooding of paved surfaces. When installing pavers around an inground pool, a 1째 slope of 1/8 inch per linear foot away from the pool is mandatory. All other paver surfaces must also have a drainage slope of 1째 for the Gator Maxx Sand to work at its optimum. For the pool coping blocks, it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use Gator Maxx Sand. Do not sweep Gator Maxx Sand over asphalt.
FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION
Gator Maxx Sand is recommended for a variety of uses, including pool sides, patios, foot paths, driveways, parking spaces, pavements etc. WITH A DRAINAGE BASE SYSTEM : The concrete pavers have to be installed on a system composed of 2 layers. The upper layer can have a maximum of 1 inch (2.5 cm) of bedding sand. The lower layer must have a minimum of 5 inches (12.5 cm) of crushed stone compacted at 95% Proctor density. WITH A NON-DRAINAGE BASE SYSTEM : (See diagrams below). You must have a minimum 1째 top surface slope for proper water run off for both systems.
DRAINAGE BASE
1.
PAVER
GATOR MAXX SAND BEDDING SAND
PAVER
2.
PAVER
maximum of 1 inch (2.5 cm)
CRUSHED STONE
GATOR MAXX SAND BEDDING SAND
PAVER
maximum of 1 inch (2.5 cm)
CRUSHED STONE
minimum of 5 inches (12.5 cm)
minimum of 2 inches (5 cm)
DRAINAGE BASE SYSTEM
minimum of 4 inches (10 cm) NON-DRAINAGE BASE SYSTEM
CONCRETE SLAB
3.
PAVER
PAVER
GATOR MAXX SAND MORTAR OR ADHESIVE
CONCRETE SLAB
minimum of 4 inches (10 cm) NON-DRAINAGE BASE SYSTEM
For diagram 3, the pavers are adhered to the concrete slab using either a thin set mortar or a permanent bond adhesive.
4.
PAVER
GATOR MAXX SAND BEDDING SAND
I N S TA L L AT I O N
FOR AN EXISTING PAVER JOB:
PAVER
maximum of 1 inch (2.5 cm)
CONCRETE SLAB
minimum of 4 inches (10 cm) NON-DRAINAGE BASE SYSTEM
* For Concrete pavers, wetcast and natural stones, the thickness & strength of the product will determine if it can be used for both pedestrian and vehicular applications.
Coverage
Quantity required depends on the shape and size of paving area, the concrete pavers as well as the width of the joints.
For 50 lb ( 22.7 Kg ) bag Narrow Joints Wide Joints
65 to 85 ft2 ( 6 to 7.4 m2 ) 22 to 42 ft2 ( 2 to 3.9 m2 )
37
INSTALLATION
Installation Eurostone
I N S TA L L AT I O N
STEP 1
STEP 2
STEP 3
FOR A DRAINAGE BASE SYSTEM: STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Install natural stones on a bedding sand. Make sure that the stones are completely interlocked. (Photo 1) Make sure that the top surface of the stones is dry. Sweep EUROSTONE BOND in between the stone joints. (Photo 2) Compact the stone joints by using a vibrating plate. (Photo 3) Sweep off all excess EUROSTONE BOND that is on the stone surface. Insure that EUROSTONE BOND lies at least 1/8’’ (3mm) below the top of the stones. Using a leaf blower, blow off all EUROSTONE BOND residue lying on the stone surface or you can also use a vacuum to remove the remaining residue. (Photo 4) Direct a fine mist of water in the air so it will gently land on on the stone and joint surface and naturally moisten the sand joint. Proceed for 10 to 15 seconds. Wait 3 to 4 minutes (not longer) and repeat the mist of rinse a maximum of 2 more times. However, stop misting and rinsing when you see a minimal amount of water retention on the stone joints. (Photo 5) NOTE : Repeat the directions of step 5, for all other stone areas that have not been watered. Use a leaf blower to remove any excess surface water lying on the stone. This blowing action is necessary to help remove any remaining Eurostone sand residue that is remaining on the paved surfaces from the previous step.
FOR AN EXISTING STONE JOB:
Using a pressure washer, remove all the existing joint filling material from the top of the stones to the bottom. Follow step 2 to step 6 of NEW STONE JOB instructions.
FOR A NON-DRAINAGE BASE SYSTEM:
i) Make sure that the stones are completely fixed in concrete and cannot move. ii) If joint depth is more than 2 3/8” (60mm), the installation will then need to be done by increment of 2’’ (5 cm). Allow 24 hours between each layer of Eurostone Bond in order to dry.
FOR NON INTERLOCKED STONES:
The installation will then need to be done in multiple layers, maximum 1.5” per layer. Allow 24 hours between each layer of Eurostone Bond in order to dry.
IMPORTANT
The water used in step 5 will activate a bonding action as well as condense EUROSTONE BOND sand in the joints. Too much water will undo the dense compaction and reduce the final perfomance of EUROSTONE BOND. If steps 3 & 4 are not done properly, a white haze may be apparent on the stone surface after the installation. This is due to excess residue left on the stone surface. This haze will dissipate over time. It can also be removed using the Gator Efflorescence cleaner.
38
INSTALLATION
Installation Eurostone
STEP 4
STEP 5
STEP 6
Do not apply on wet or damp surface since bonding action will cause Eurostone Bond to stick on surface and avoid proper sliding in joint. Do not use if rain is forecasted within 1 hour. Avoid excessive watering or flooding of paved surfaces. When installing stones around an underground pool, a 1° slope of 1/8 inch (3 mm) per linear foot away from the pool is mandatory. All other paver surfaces must also have a drainage slope of 1° for the Eurostone Bond to work at its optimum. For the pool coping units, it is mandatory to use mortar in the joints.
FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION
EUROSTONE BOND is recommended for a variety of uses, including pool sides, patios, foot paths, driveways, parking spaces, pavements etc… WITH A DRAINAGE BASE SYSTEM : The stone pavers have to be installed on a system composed of 2 layers. The upper layer can have a maximum of 1 inch (2.5 cm) of bedding sand. The lower layer must have a minimum of 5 inches (12.5 cm) of crushed stone compacted at 95% Proctor density. WITH A NON-DRAINAGE BASE SYSTEM: (See diagrams below). You must have a minimum 1° top surface slope for proper water run off for both systems.
1.
NATURAL EUROSTONE NATURAL STONE STONE SAND BEDDING SAND
maximum of 1 inch (2.5 cm)
2.
NATURAL EUROSTONE NATURAL COBBLESTONE COBBLESTONE SAND MORTAR BED BASE (SAND COAT)
CRUSHED STONE
3.
NATURAL COBBLESTONE
2nd Layer EUROSTONE 1st Layer EUROSTONE
NATURAL COBBLESTONE
MORTAR BED BASE (SAND COAT)
CRUSHED STONE
4.
NATURAL EUROSTONE NATURAL STONE STONE SAND BEDDING SAND
maximum of 1 inch (2.5 cm)
CONCRETE SLAB
CRUSHED STONE
minimum of 5 inches (12.5 cm)
minimum of 5 inches (12.5 cm)
minimum of 4 inches (10 cm)
DRAINAGE BASE SYSTEM
NON-DRAINAGE BASE SYSTEM
NON-DRAINAGE BASE SYSTEM
NON-DRAINAGE BASE SYSTEM
minimum of 5 inches (12.5 cm)
I N S TA L L AT I O N
PLEASE NOTE
Coverage
Quantity required depends on the shape and size of paving area, the concrete pavers as well as the width of the joints.
For 50 lb ( 22.7 Kg ) bag Narrow Joints Wide Joints
70 to 90 ft2 ( 6.5 to 8.4 m2 ) 24 to 46 ft2 ( 2.2 to 4.3 m2 )
39
INSTALLATION
Installation Gator Dust
I N S TA L L AT I O N
STEP 1
STEP 2
STEP 3
STEP 4
FOR A NEW PAVER JOB: STEP 1 STEP 2
Install stones on a drainage base system. Make sure the stone’s top surface is dry.
FOR NATURAL STONES: Using a hard-bristle, heavy-duty construction broom, sweep GATOR DUST in between the natural stone joints.
FOR WETCAST STONES: Using a scoop, carefully pour GATOR DUST in between the joints and avoid getting any GATOR DUST on the stone surface.
STEP 3
Hit the stones with a rubber mallet; this will make the GATOR DUST settle firmly into the joints by removing the air pockets. Repeat step 2 and this step 3 at least two more times. (Photo 3) Using a soft, fine-bristle broom, sweep all excess GATOR DUST off stone surfaces. Insure that GATOR DUST lies at least 1/8 inch (3 mm) below the top of the stones. (Photo 4) Using a leaf blower, blow all GATOR DUST residues lying on the stone surface. Depending on the physical layout present, it may be more appropriate to remove residue by using a vacuum unit. (Photo 5) First watering phase: At a height of 4 feet (1.2 m), use a water gun connected to a hose to direct a fine mist (setting of water gun: “mist” or equivalent) of water on a certain stone area for 10 to 15 seconds. Wait 3 to 4 minutes (not longer). Proceed to Second watering phase. Second watering phase: From a height of 2 feet (.60 m), aim the water mist directly at the stone surface. Mist and rinse simultaneously so as to eliminate any GATOR DUST residue left on the stones. The GATOR DUST residue should go directly into the stone joints. Wait 3 to 4 minutes (not longer). Proceed to Third watering phase. Third watering phase: From a height of 2 feet (.60 m), aim the water mist again directly at the stone surface. Again, mist and rinse simultaneously so as to eliminate any GATOR DUST residue left on the stones. The GATOR DUST residue should go directly into the stone joints. However, stop misting (ALERT) when you see a minimal amount of water retention on the stone joints. (Photos 6)
STEP 4 STEP 5 STEP 6 STEP 7
NOTE : Repeat the directions of step 6 for all other areas that have not been misted with water. (Photos 6) Use a leaf blower to remove all excess surface water lying on stone pores and crevices. This blowing action is necessary to help remove any remaining GATOR DUST residue left on stone surface from the previous steps. Depending on the physical layout present, it may be more appropriate to remove remaining residue with a vacuum unit. (Photo 7)
IMPORTANT
The water used in step 6 will activate a bonding action as well as condense GATOR DUST in the joints. Too much water will undo the dense compaction obtained during step 3 and reduce the final performance of GATOR DUST. If steps 4, 5, 6 and 7 are not done properly, a white haze may appear on the stone surface after the installation. This is due to excess GATOR DUST residue left on the stone surface. This haze will dissipate over time. It can also be removed by using a concrete efflorescence cleaner.
40
INSTALLATION
Installation Gator Dust
STEP 5
STEP 7
STEP 6
Gator Dust becomes very firm but will crack if the crushed stone base has movement. By following the installation instructions carefully, you will obtain a very hard jointing material. It should be noted that Gator Dust will continue to harden over time. Do not apply on wet or damp surfaces, since bonding action will cause Gator Dust to stick on surface and avoid proper sliding in joint. Do not use if rain is expected within 24 hours. Avoid excessive watering or flooding of stone areas. When installing stones around an inground pool, a slope of 1/8 inch (3 mm) per linear foot away from the pool is mandatory. All stone surfaces must have a drainage slope for Gator Dust to work optimally. For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the stone installation around the pool, you can use Gator Dust. Do not sweep Gator Dust over asphalt.
FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION OK OK
NOTOK OK NOT
GATOR DUST STONE STONEGATOR DUST STONE STONE
GATOR DUST DUST STONE GATOR STONE STONE STONE
BEDDING SAND
BEDDING maximum of SAND 1 inch (2.5 cm) maximum of 1 inch (2.5 cm)
CRUSHED STONE
CRUSHED STONE minimum of 5 inches (12.5 cm) minimum of 5 inches (12.5 cm)
JOINT FILLED PROPERLY JOINT FILLED PROPERLY (JOINT COMPLETELY FILLED WITH GATOR DUST) (JOINT COMPLETELY FILLED WITH GATOR DUST)
DRAINAGE BASE DRAINAGE BASE
DRAINAGE BASE DRAINAGE BASE
GATOR DUST is recommended for a variety of uses, including patios, walkways and pool decks.The stones have to be installed on a drainage base system: maximum of 1” (2.5 cm) of bedding sand, plus a minimum of 5” (12.5 cm) of crushed stone compacted at 95% Proctor density.(See diagrams below).
I N S TA L L AT I O N
PLEASE NOTE
OTHER PRODUCT OTHER PRODUCT
BEDDING SAND
BEDDING maximum of SAND 1 inch (2.5 cm) maximum of 1 inch (2.5 cm)
CRUSHED STONE
CRUSHED STONE minimum of 5 inches (12.5 cm) minimum of 5 inches (12.5 cm) JOINT NOT FILLED PROPERLY JOINT NOT FILLED PROPERLY (JOINT DILUTED WITH OTHER PRODUCT) (JOINT DILUTED WITH OTHER PRODUCT)
Coverage
The quantity required depends on the shape and size of the stones as well as the width of the joints. One bag of 50 lbs (22.7 kg) of this product will cover between 20 to 30 square feet ( 1.86 to 2.78 m2 ) if the joints are about 1” to 2” ( 2.54 cm to 5.08 cm) wide and the stones are about 2“ to 2-1/2” ( 5.08cm to 6.35 cm) thick.
For 50 lb ( 22.7 Kg ) bag Narrow Joints
20 to 30 ft2 ( 1.86 to 2.78 m2 )
41
WARRANTY
ALLIANCE WARRANTY
Gator Sands & Dust Limited Warranty 10 YEAR LIMITED WARRANTY FOR RESIDENTIAL PURPOSES ONLY
Please note that this limited warranty applies only when the Gator Super Sand, Gator XP, Gator Maxx, Euro Stone and Gator Dust are used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use). Alliance Designer Products Inc. cannot guarantee results as it has no control over surface and sub-surface preparation and product application. However, for a period of 10 years from purchase, Alliance Designer Products Inc. agrees that, if the product is proven to be defective, and on the condition that is was installed pursuant to the method of application of surface and sub-surface preparation described in the *installation guide, then Alliance Designer Products Inc. agrees to refund the purchase price. Proof of purchase is required for any claim. The parties agree that the refund of the purchase price as stated is the only obligation of Alliance Designer Products inc. In all events, Alliance Designer Products Inc. shall not be liable for any other damages or costs ( including removal or reinstallation of sand or pavers) whatsoever, direct or consequential, to the extent permitted by law, Alliance Designer Products Inc. excludes any implied warranty of quality merchantability or fitness for purpose.
1 YEAR LIMITED WARRANTY Please note that when the Gator XP, Gator Maxx, Euro Stone and the Gator Dust are used for other purposes (mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from the purchase. * ICPI Tech Spec number 2 ( Construction of Interlocking Concrete Pavements)
Gator Natural Look Sealer Limited Warranty Gator Natural Look Sealer is made from an advanced high-tech patented formula called Gator Stone Guard. This breathable long lasting sealer deeply penetrates into the concrete & stone pores providing an invisible & durable shield that will protect your hardscape investment for up to 10 years.
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O a l l i a n c e g a t o r. c o m
42
ADVANTAGES
1 hr Setting Time Above 32°F For Gator Super & XP Sand
SETTING TIME
1HR SETTING TIME AT ABOVE 32°F
Alliance is the only polymeric sand manufacturer that provides a one-hour setting time. Other polymeric sands require you to come back the following day to finish your work, and potential rainfall during the same day as the sand’s application would normally wash out the sand from the paver joints. But with Alliance, you will be able to collect your dues earlier for work done better and sooner. Also, who else in the polymeric sand industry but Alliance enables you to perform this work at any temperature above 32°F (0°C), start your season earlier and extend it at least two months? With the competition, you have to wait for Mother Nature to give you a comfortable 59°F (15°C), you get two months less work time and a lower profit margin.
F O R P R O D U C T K N O W L E D G E P L E A S E R E F E R T O A l l i a n c e G a t o r. c o m
43
THE PERFECT BALANCE OF STRENGTH & DURABILITY
Quality is our Strength Toll free: 1-866-212-1611