Project
Type
DESCRIPTION The Canopy Star canopy LED luminaire from US LED is a perfect solution for parking structures, shopping area walkways, petrol stations and exterior canopies. The Canopy Star LED canopy is surface mounted for easy adaptation with a typical mounting height of 10 to 25 feet. Designed to illuminate area features with sharp, accurate color to increase security and visibility, the Canopy Star is cost effective to install and will replace conventional fluorescent, HPS and metal halide lighting.
Canopy LED Luminaire Standard Flux
FEATURES l l l l l
112 W / 12,600 Lumens
Class 2 compliant design (low voltage, limited power) L70 lifetime of >200,000 hours* Luminaire is IP66 compliant Protective coating added to resist corrosion 5-year warranty
CERTIFICATION l l l
UL 1598 certified by Intertek (ETL 4006735) DesignLights Consortium qualified LM-79 available
ENERGY DATA Input Voltage (VAC) System Level Power (W)
Example: CNP3-50-2
110
Delivered Lumens (Lm)
12600
12600
System Efficacy (Lm/W)
112.5
114.5
Color Temperature (K)
5000
5000
Color Rendering Index
80 min
80 min
L70 Calculated Life (Hrs)*
>200,000
>200,000
L85 Calculated Life (Hrs)*
150,000
150,000
-40 to 45
-40 to 45
* US LED product ‘Lifetimes’ refer only to the LED light engine, not the power source, and are based on the Illuminating Engineering Society’s TM21 methodology based on 25°C/77°F ambient temperature. The lifetimes are solely meant to be a guide for expected LED degradation and not a warranty or predictive of their actual life, which can be affected by ambient temperatures and other factors.
CNP3
50
2
Series
Color Temp (K)
Fixture Color
SPECIFICATIONS
2 White
Units/carton
CNP3
50 5000K
347-480
112
Operating Temp (ºC)
FIXTURE ORDERING INFORMATION
120 - 277
Dimensions (in) Net weight Environmental Rating
18.62 x 18.62 x 2.75 1 9 lbs Wet
POWER SUPPLY INFORMATION Example: PUC-UNV1-4100
Series
Type
Drive Current
PUC
UNV1- (120-277 VAC)
4100 (Non-Dimmable)
PUC
UNV1 - (120-277 VAC)
4100DM (Dimmable)**
PUC
UNV2 - (347/480 VAC)
4100DM (Dimmable)***
** PUC-UNV1-4100DM is not DesignLights Consortium qualified. Special order only. *** Special order only.
Specifications and dimensions subject to change without notice
DATASHEET 11.20.2014
| | | | | Brite Energy Solutions - Tom Knoblock - 1-844-533-2897 Toll Free - www.Brite-LED-Solutions.com
Project
Type
Catalog #
DESCRIPTION The Canopy Star canopy LED luminaire from US LED is a perfect solution for parking structures, shopping area walkways, petrol stations and exterior canopies. The Canopy Star LED canopy is surface mounted for easy adaptation with a typical mounting height of 10 to 25 feet. Designed to illuminate area features with sharp, accurate color to increase security and visibility, the Canopy Star is cost effective to install and will replace conventional fluorescent, HPS and metal halide lighting.
Canopy LED Luminaire High Flux
FEATURES l l l l l
190 W / 19,700 Lumens
Class 2 compliant design (low voltage, limited power) L70 lifetime of >200,000 hours* Luminaire is IP66 compliant Protective coating added to resist corrosion 5-year warranty
CERTIFICATION l l l
UL 1598 certified by Intertek (ETL 4006735) DesignLights Consortium qualified LM-79 available
ENERGY DATA Input Voltage (VAC)
120 - 277
System Level Power (W) Delivered Lumens (Lm) System Efficacy (Lm/W) Color Temperature (K) Color Rendering Index L70 Calculated Life (Hrs)* L85 Calculated Life (Hrs)* Operating Temp (ºC)
FIXTURE ORDERING INFORMATION 50
Series
Color Temp (K)
Fixture Color
CNP4
50 5000K
1 Bronze**
189
19,700
19,800
104
105
5000
5000
70 min
70 min
>200,000
>200,000
150,000
150,000
-40 to 45
-40 to 45
* US LED product ‘Lifetimes’ refer only to the LED light engine, not the power source, and are based on the Illuminating Engineering Society’s TM21 methodology based on 25°C/77°F ambient temperature. The lifetimes are solely meant to be a guide for expected LED degradation and not a warranty or predictive of their actual life, which can be affected by ambient temperatures and other factors.
Example: CNP4-50-2
CNP4
347-480
190
SPECIFICATIONS Dimensions (in)
18.62 x 18.62 x 2.75
Units/carton
2 White
1
Net weight
9 lbs
Environmental Rating
Wet
POWER SUPPLY INFORMATION Example: PUC-UNV1-8200
Series
Type
Drive Current
PUC
UNV1- (120-277 VAC)
8200 (Non-Dimmable)
PUC
UNV1 - (120-277 VAC)
8200DM (Dimmable)**
PUC
UNV2 - (347/480 VAC)
8200DM (Dimmable)**
** Special order only.
PRELIMINARY DATA SUBJECT TO CHANGE DATASHEET 11.20.2014
Specifications and dimensions subject to change without notice
US LED
|
6807 PORTWEST DR
|
HOUSTON, TX 77024
|
T 866 972 9191
|
F 713 972 9393
|
info@usled.com
|
www.usled.com
INSTALLATION GUIDE CNPx-50
WARNING l
The installation must only be performed by a licensed electrician.
l
To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.
l
Disconnect power before installing the product or servicing it.
l
Wait until fixture has cooled down before installing or servicing the fixture.
l
MIN. 90°C SUPPLY CONDUCTORS
MODEL NUMBERS This installation instructions covers the following products: Power Supplies 1. 50W Power Unit: PUC-UNV1-2100 or PUC-UNV2-2100 2. 75W Power Unit: PUC-UNV1-3000 or PUC-UNV2-3000 3. 96W Power Unit: PUC-UNV1-3570 or PUC-UNV2-3570 4. 192W Power Unit: PUC-UNV1-7140 or PUC-UNV2-7140 Luminaires 1. CNP1-50 Series Luminaires 2. CNP2-50 Series Luminaires
BOX CONTENTS
Tools Needed 1. 4” Hole Saw 2. #2 Phillips Screw Driver 3. ¼” Hex Driver
Mounting Plate Assembly
CanopyStar Fixture
LED Driver with Mounting Bracket
Wire Harness/Cover Assembly
Page 1 #44-000017 Updated 09.26.13
INSTALLATION GUIDE CNPx-50
INSTALLATION INSTRUCTIONS 1. Using 4” hole saw, cut hole in canopy where fixture is to be mounted. Hole location needs to be centered between canopy ribs to allow wire harness/cover assembly to fit. 2.
Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4” hole and secure by tightening mounting tab screws using #2 Phillips screw driver. See Figures 1 and 2.
Mounting tab screws
4” hole
Mounting tabs
FIG 1
3.
FIG 2
Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding locking plate forward into slot and tightening #6-32 locknut. See Figures 3 and 4. Locking plate
Locknut
FIG 3
FIG 4
Page 2 #44-000017 Updated 09.26.13
INSTALLATION GUIDE CNPx-50
INSTALLATION INSTRUCTIONS 4.
Route wires through center of mounting plate assembly. See Figure 5.
5.
Take wire harness assembly and make power connections using approved electrical connector. See wire diagrams.
FIG 5
6.
FIG 6
Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant screws supplied. See Figure 7.
7. Complete installation by swinging fixture into place and securing with mounting screws using #2 Phillips driver. See Figure 8.
FIG 7
FIG 8
Page 3 #44-000017 Updated 09.26.13
US LED
INSTALLATION GUIDE CNPx-50
INSTALLATION INSTRUCTIONS - DRIVER BOX 1.
Turn off main power.
2.
Secure driver box assembly to mounting bracket by tightening mounting screws using ¼” hex driver. See Figure 9.
3.
Secure mounting bracket to any vertical wall using #10 sheet metal screws supplied. Insure location allows wire harness to reach low voltage side of power supply box. See Figure 10.
4.
Make internal primary side (high voltage) power connections by connecting wires, Black to Load, White to Neutral and Green to Ground using approved electrical connector. See wire diagrams.
5.
Make secondary (low voltage) connections by using approved electrical connector. See wire diagrams.
6.
Secure driver box top using #8 sealing machine screws supplied.
7.
Turn on power.
Mounting screws
FIG 9
FIG 10
Page 4 #44-000017 Updated 09.26.13
US LED
INSTALLATION GUIDE CNPx-50
WIRING DIAGRAMS FOR CNP1-50 LUMINAIRES WITH TRANSFORMER
WITHOUT TRANSFORMER
Page 5 #44-000017 Updated 09.26.13
US LED
INSTALLATION GUIDE CNPx-50
WIRING DIAGRAMS FOR CNP2-50 LUMINAIRES WITH TRANSFORMER, 2 DRIVERS
WITHOUT TRANSFORMER, 2 DRIVERS
Page 6 #44-000017 Updated 09.26.13
US LED
SURFACE MOUNT KIT INSTALLATION GUIDE CNPx-50
WARNING l
The installation must only be performed by a licensed electrician.
l
To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.
l
Disconnect power before installing the product or servicing it.
l
Wait until fixture has cooled down before installing or servicing the fixture.
l
MIN. 90°C SUPPLY CONDUCTORS
1.
Mount the Hinge, Latch, Driver Bracket, and Driver Assembly to the Plate using Hex Locknut with nylon SS 8-32 (Fig 1).
2.
Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4� hole and secure by tightening mounting tab screws using #2 Phillips screw (Fig 2).
FIG 1
3.
FIG 2
Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding locking plate forward into slot and tightening #6-32 locknut. Swing fixture into place and securing with mounting screws using #2 Phillips driver (Fig 3).
FIG 3
Page 1 Updated 03.28.14
SURFACE MOUNT KIT INSTALLATION GUIDE CNPx-50 4.
Route wires through center of mounting plate assembly. Take wire harness assembly and make power connections using approved electrical connector. Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant screws supplied (Fig 4).
5.
Mount the Base of the Canopy Star Surface Mount Kit using Hex Washer HD Sheet Metal Screws, STL #10, 1� (Fig 5).
6.
Mount the CanopyStar Surface Mount Plate Assembly to the Base using #10, .500, Zinc-Plated Steel Screw (Fig 6).
FIG 4
FIG 5
FIG 6
Page 2 Updated 03.28.14