TANDEMBOX Assembly, removal and adjustment
IMPORTANT 16mm Nickel Screws
Side Adjustment (to the left 1mm)
Side Adjustment (to the right 1mm)
Height Adjustment +/- 2mm
Front Assembly
1. Insert gallery rail into front 2. Swing open to fasten 3. Clip on gallery rail at back
Gallery Assembly
Drawer Insertion
Front Removal
HIGH FRONTED PULL-OUT
Pan Sink Drawer (Standard Similar)
Tilt Adjustment
Drawer Removal
METABOX Assembly, removal and adjustment
Front Assembly Removal
Front Assembly Removal
Height Adjustment
Height Adjustment
Side Adjustment
Drawer Insertion & Removal
For in excess of 15 kg: Use additional screw above roller
Assembly
High Fronted Pull-Out
William Ball Hinge Plates
Clip-on Hinges 30o
2
Door Buffers
2
Wood Dowels
Shelf Supports
2
Cover Caps
10
!
Angled Base Unit
5mm
Nickel Screws
20
16mm
4
Leg Sockets
4
4
Quickfit Bolts
Cams
10
10
370
Legs
Plinth Clips
4
2
Steel Screws
18mm
16
2
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly having determined product required
Quick Fit Bolt
Cam
Shelf Support
Base Panel
End Panels (L.H. Shown)
715 Door
Dowel OR 570 Door
Hinge Plate
NOTE !
OR
Cover Caps
Door Buffer
Hinge Plates must be attached to narrow panel
To Handing as Required
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Angled Base Unit
ASSEMBLE
TOOLS REQUIRED
In alphabetical sequence
370
COMPONENTS A B C D E F
End Panel Base Panel Top Panel Back Panel End Panel Legs Shelf
E R.H. End Panel
C
D
Top Panel
Back Panel
B
A
Base Panel
L.H. End Panel
150o
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
F
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball Wood Dowels
6
!
Quickfit Bolts
Cams
6
Door Buffers
2
Angled Wall Unit
Cover Caps
Concealed Hanger
6
2
Clip-on Hinges 30o
5mm
16
Nickel Screws
2
4
16mm
715 x 370 & 895 x 370
Joined Hanging Plate
Hinge Plates
Hanger Cover Cap
2
2
2
Shelf Supports
Cover Caps
8
2
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly having determined product required
Quick Fit Bolt
Cam Shelf Support
Top/Base Panel
Dowel
End Panel
Hinge Plate OR Door Buffer Concealed Hanger To Handing as Required NOTE ! Hinge Plates must be attached to narrow panel
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Angled Wall Unit
715 x 370 & 895 x 370
ASSEMBLE
COMPONENTS
In alphabetical sequence
A B C D E F
TOOLS REQUIRED
Cover Cap
Base Panel Top Panel Back Panel End Panel Hanger Shelf
Cap hole after fitting
E
End Panel
R.H. End Panel
C
D
Top Panel
Back Panel
B
A
Base Panel
L.H. End Panel
F
Concealed Hanger Note pull down tab to lock hanger to cabinet
42 150o
Dual Fitting 3mm 90o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
30mm 30mm
0o
Side View
End of Run Fitting
WBU 691
C
William Ball
Butler Sink Base Units 600 & 800
600 Cover Caps
Both 600 & 800 Door Buffers
Nickel Screws 16mm
Sprung Catch
800
Leg Sockets
Legs
Plinth Clips
4
Cover Caps
Cover Caps
5mm
2
2
8
4
4
4
4
8
Hinge Plates
Clip-on Hinges
Steel Screws
Cams
Wood Dowels
Quickfit Bolts
Hinge Plates
Clip-on Hinges
2
2
16
12
12
12
4
4
!
18mm
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly Quick Fit Bolt
Tandem Drawer
Cam
Meta Box Drawer
Top / Base Panel
End Panels (L.H. Shown)
Back Rail Dowel Door
Sprung Catch
Hinge Plate
OR
Door Buffer
To Handing as Required
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Butler Sink Base Units 600 & 800
ASSEMBLE
COMPONENTS
TOOLS REQUIRED
In alphabetical sequence
A B C D E F G
E
Base Panel Top Panel Back Panel End Panel Back Rail Legs
R.H. End Panel
F Back Rail
C
End Panel
D
Back Panel
Top Panel
A L.H. End Panel
B Base Panel
NOTE FIX BACK RAIL INTO PLACE AFTER PLUMBING 150o
90o
0o
G Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball Wood Dowels
Worktop Coffee Dresser Unit
Quickfit Bolts
Cams
12
12
12
Hinge Plates
Cover Caps
Door Buffers
2
2
2
!
Concealed Hanger
16mm
Hanger Cover Caps
Joined Hanging Plate
2 Nickel Screws
1210
2
2
Shelf Support
W/Top Fix Blocks
8
4
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly having determined product required
Rails Shelf Support Cam
Concealed Hanger
Dowel Top/Mid Panel
Quick Fit Bolt
End Panels
Hinge Plate
OR
Door Buffer Tandem Drawer
To Handing as Required Meta Box Drawer
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Worktop Coffee Dresser Unit
ASSEMBLE
TOOLS REQUIRED
In alphabetical sequence
1210
COMPONENTS A B C D E F
End Panel Mid Panel Top Panel Back Panel End Panel Base Panel Shelves
PLACE UNIT IN AN UPRIGHT POSITION BEFORE FIXING BASE PANEL WITH BLOCKS
COMPONENTS A B C D E F G
End Panel Mid Panel Top Panel Back Panel Base Panel End Panel Rail Shelves
WARNING THIS UNIT MUST BE FIXED TO A WALL WBU 691
C
William Ball Corner Base Unit Cover Caps
Hinge Plates
2
2
Hi-Lo Screws
Wood Dowels
Clip-on Hinges
Door Buffers
5mm
!
17
Legs
Plinth Clips
Conformat Screws
2
5
5
5
2
3
Quickfit Bolts
Cams
Steel Screws
Pushfit Bolts
16mm
Worktop Fix Blocks
8
2
8
45 x No.8
4
Leg Sockets
Nickel Screws
2 Cover Caps
Shelf Support
With Blanking Panel 1000
28
18mm
12
4
20
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
!
Tandem Drawer
TANDEM DRAWER Drawer rail must be in middle position
Push Fit Bolt
!
Shelf Support Cam
Base Panel
Meta Box Drawer End Panel (L.H. Shown)
Rails
715 Door
Dowel 570 Door
Position drawer rail to suit drawer system selected. For 715 doors use metabox drawer position.
Quick Fit Bolt
715 Door Door Buffer 570 Door Hinge Plate Meta Box Drawer
Tandem Drawer
Check handing of unit required before fitting drawer runner and/or hinge plates
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball Corner Base Unit ASSEMBLE
With Blanking Panel 1000
TOOLS REQUIRED
In alphabetical sequence
COMPONENTS A B C D E
F
End Panel Base Panel Back Rail Back Panel Front Rail
F G H I
End Panel Post Drawer Rail
Blanking Panel Shelf (1) Fillets (2)
End Panel
Post Positioned to suit door width selected (496 door shown)
C
D
Back Rail
E
Back Panel Tandem Drawer
Front Rail
Dowel
Meta Box Drawer
Shelf Support Conformat Screw
G
H
Drawer Rail & Post
Dowel
I Blanking Panel Conformat Screw
A
B
End Panel
Base Panel
Hi-Lo Screw
150o
Blocks Worktop fixing block positioned close to back rail as required by fitters.
90o
0o
IMPORTANT Flange must overhang gable end
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o) WBU 691
C
William Ball Diagonal Corner Wall Unit FITTINGS FOR 575, 720 AND 900 Joined Hanging Plate
Concealed Hanger
Hanger Cover Cap
Wood Dowels
575
Quickfit Bolts
Cam
Cover Caps
575 high 600 x 600 720 high 600 x 600 900 high 600 x 600
720 5mm
Cover Caps
900 5mm
Cover Caps
5mm
2
2
2
8
12
12
15
10
20
Door Buffers
Clip-on Hinges
Hinge Plates
Cover Caps
Nickel Screws
Shelf Support
Shelf Support
Shelf Support
16mm
Conformat Screws
4
8
5
10
10
2
!
2
2
2
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Quick Fit Bolt
Shelf Support
Concealed Hanger
Top/Base Panels
Do or Po sts
End Panel
Dowel Cam
Hinge Plate
OR
(One post with hinge plates other with door buffers.) Door Buffer
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball Diagonal Corner Wall Unit ASSEMBLE
575 high 600 x 600 720 high 600 x 600 900 high 600 x 600
COMPONENTS
A C E G H
In alphabetical sequence
TOOLS REQUIRED
B D F
575 720 900
Top Panel
1
1
1
Back Panel
1
1
1
Back Panel
1
1
1
End Panel
1
1
1
Door Posts
2
2
2
Shelf
1
2
2
End Panel Base Panel Diagonal Panel
F Back Panel
E
Cover Cap Cap hole after fitting
Diagonal Back Panel
B Top Panel
D
C
Back Panel
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
Base Panel
A End Panel
150o
90o
0o
G
En dP ane l
Concealed Hanger Note pull down tab to lock hanger to cabinet
H Do or hin Pos ge t w pla ith te
Conformat Screw
H Do or Po bu st w ffe r ith
42
Dual Fitting 3mm 30mm 30mm
Side View
End of Run Fitting
WBU 691
C
William Ball
Double Base Units
700, 800, 900, 1000 & 1200
FITTINGS FOR 700, 800, 900, 1000 AND 1200 Cover Caps
4
Hinge Plates Clip-on Hinges Door Buffers
4
Nickel Screws Wood Dowels
!
13
Leg Sockets
Legs
1200 Conformat Screws
Steel Screws
16
4
4
5
4
4
3
Plinth Clips
Cover Caps
Quickfit Bolts
Cams
Pushfit Bolts
5mm
Worktop Fix Blocks
28
2
8
16mm
12
Shelf Support
2
12
Legs
Leg Sockets
Plinth Clips
3
18mm
4
6
6
Steel Screws
Nickel Screws
18mm
16mm
24
14
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
!
Tandem Drawer
TANDEM DRAWER Drawer rail must be in middle position
Push Fit Bolt
!
Shelf Support Cam
Base Panel
Meta Box Drawer End Panel (L.H. Shown)
Rails
715 Door
Dowel
OR 570 Door Position drawer rail to suit drawer system selected. For 715 doors use metabox drawer position.
Quick Fit Bolt
715 Door Hinge Plate 570 Door Door Buffer Meta Box Drawer
Tandem Drawer
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Double Base Units
ASSEMBLE
TOOLS REQUIRED
In alphabetical sequence
Base Panel Back Rail Back Panel
F G H J
End Panel Drawer Rail Post Leg Shelf
Front Rail
D
Back Rail
Front Rail
End Panel
End Panel
C Dowel
COMPONENTS A B C D E
F
E
700, 800, 900, 1000 & 1200
Back Panel
Tandem Drawer Meta Box Drawer
Shelf Support
G H Conformat Screw
Dowel
Drawer Rail & Post
A End Panel
Conformat Screw
B Base Panel
Blocks Worktop fixing block positioned close to back rail as required by fitters. 150o
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
J
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball
Double Wall Units
FITTINGS FOR 355, 570 AND 715 Wood Dowels
Quickfit Bolts
Concealed Hanger
Cam
355 high 1000 (No Shelf) 570 high 800, 900 & 1000 715 high 700, 800, 900 & 1000
355
Joined Hanging Plate
Hanger Cover Cap
570
Cover Caps
5mm
Cover Caps
715 5mm
Cover Caps
5mm
10
8
8
2
2
2
0
12
8
Clip-on Hinges
Cover Caps
Hinge Plates
Door Buffers
Nickel Screws
Shelf Support
Shelf Support
Shelf Support
16mm
Conformat Screws
8
2
0
5
10
4
!
4
4
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Cam Shelf Support
Top/Base Panels
End Panel
Dowel
Quick Fit Bolt Hinge Plate
Door Buffer
Post
Concealed Hanger
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
355 high 1000 (No Shelf) 570 high 800, 900 & 1000 715 high 700, 800, 900 & 1000
Double Wall Units TOOLS REQUIRED
ASSEMBLE
COMPONENTS
A C E
In alphabetical sequence
End Panel Top Panel End Panel Shelf
B D F
355 570 715
Base Panel
1
1
1
Back Panel
1
1
1
Post
1
1
1
0
1
2
Cover Cap Cap hole after fitting
E
R.H. End Panel
D
Back Panel
C
Dowel
Top Panel
B
Shelf Support
Base Panel
Conformat Screw
F
Dowel
Post
A Conformat Screw L.H. End Panel
G 42
Concealed Hanger 150o
Note pull down tab to lock hanger to cabinet
Dual Fitting 3mm 90o 30mm 30mm
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
Side View
End of Run Fitting
WBU 691
C
William Ball
Drawer Pack
Leg Sockets
!
Legs
300, 400, 500, 600, 800 & 1000
Plinth Clips
4
4
2
Cams
Push Fit Bolts
Worktop Fixing Blocks
12
4
2
Wood Dowels
Quick Fit Bolts
12 Steel Screws
8 Nickel Screws
18mm
16
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Tandem Drawer
Cam
Meta Box Drawer
Push Fit Bolt Base Panel
End Panel (L.H. Shown) Dowel Rails
Quick Fit Bolt
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
16mm
William Ball
Drawer Pack
ASSEMBLE
300, 400, 500, 600, 800 & 1000
TOOLS REQUIRED
COMPONENTS
In alphabetical sequence
A B C D E F G
F
End Panel Base Panel Back Rail Back Panel Front Rail End Panel Legs
R.H. End Panel
C D
Back Rail
E
Front Rail
Back Panel
B Base Panel
A L.H. End Panel
Blocks Worktop fixing block positioned close to back rail as required by fitters.
150o
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o) TANDEM BOX
6 5
3mm Hole 27mm
37mm A
8 7
B
C
D
E
F
A
B
C
D
E
379mm
F 11 10 9 8 7 6 5
4 3 2 1
IMPORTANT Flange must overhang gable end
METABOX 5mm Hole
261mm
G
4 3 2 1
METABOX
TANDAM - METABOX
678
(140)
630
534
(140)
495
390
(140) 341.5
246
(140)
198
TANDAM - METABOX
678
(140)
630
534
(140)
495
390
102
(140) A
453
(283)
630
341.5
166 166
(283) 54.5
54.5
54.5 B
TANDAM - METABOX
TANDAM
EXAMPLE
(140)
(140) 341.5
(283)
TANDAM - METABOX
METABOX
TANDAM
678
C
Tandam Metabox
A 8 6 4 2 1
A 11 9 5 3 1
642
(175) 594.5
642
(175) 594.5
462
(175) 414.5
462
(175) 414.5
292
(175) 234.5 166
(355)
102
(175) D
54.5
526
166
(355) 414.5
(355)
54.5 E
54.5 F
WBU 691
C
William Ball Wood Dowels
Worktop Dresser Unit
Quickfit Bolts
Cams
12
12
12
Hinge Plates
Cover Caps
Door Buffers
2
2
2
!
Concealed Hanger
Joined Hanging Plate
Hanger Cover Caps
2
2
2 Nickel Screws
16mm
1210, 1390
Shelf Support
4
8
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly having determined product required
Rails Shelf Support Cam
Concealed Hanger
Dowel Top/Mid Panel
Quick Fit Bolt
End Panels
Hinge Plate
OR
Door Buffer Tandem Drawer
To Handing as Required Meta Box Drawer
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Worktop Dresser Unit
ASSEMBLE
1210, 1390
COMPONENTS
TOOLS REQUIRED
A B C D E F G
In alphabetical sequence
Cover Cap
End Panel Mid Panel Top Panel Back Panel Rail Rail End Panel Shelves
Cap hole after fitting
G R.H. End Panel
C
D
Top Panel
Back Panel
B E
Mid Panel
A L.H. End Panel
F
Concealed Hanger Note pull down tab to lock hanger to cabinet 150o
90o 0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
WBU 691
C
High Chest / Cupboard / Filing Unit
William Ball Wood Dowels
Cams
Quickfit Bolts
Leg Sockets
8
12
12
4
Door Buffers
Nickel Screws
2
8
!
Steel Screws
18mm
Cover Caps
16
300 400 500 600 HC30 HC40 HC50 HC60 Legs
Plinth Clips
4
4 5mm
Shelf Supports
32
Sleeves & Screw
2
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly having determined product required
Quickfit Bolt
Cam
Top / Base Panel
Dowel
Meta Box Drawer
End Panel (L.H. Shown) 655 Door Tandem Drawer 535 Door
Shelf Support
OR Screw After base plate adjustment
Hinge Plate Cover Caps
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
High Chest / Cupboard / Filing Unit
ASSEMBLE
300 400 500 600 HC30 HC40 HC50 HC60
COMPONENTS
TOOLS REQUIRED
In alphabetical sequence
A B C D E F
End Panel Base Panel Top Panel Back Panel End Panel Legs
E R.H. End Panel
D Back Panel
C Top Panel
B A
Base Panel
L.H. End Panel
F IMPORTANT Flange must overhange gable end. Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
William Ball “L” Shape Corner Base Cover Caps
Hinge Plates
Clip-on Hinges
Door Buffers
Shelf Support
Leg Sockets
Legs
2
2
2
2
6
6
6
Dome Head Screws 13 x 5/3
Countersunk Screws 13 x 3
Wood Dowels
Quickfit Bolts
Cam
Steel Screws
Nickel Screws
18mm
16mm
2
2
12
24
14
!
16
16
900Sq & 1000Sq Plinth Clips
Magnetic Catch
5
1
Cover Caps
5mm
34
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Cam
Quick Fit Bolt
Shelf Support
Base Panels (Top Similar)
End Panel
Dowel
Hinge Plate
OR
Door Buffer
To Handing as Required
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball “L” Shape Corner Base ASSEMBLE
COMPONENTS
TOOLS REQUIRED
In alphabetical sequence
A B C D E F G H
!
Important Ensure that shelf F is placed inside, safely, before end panel H is located and locked.
H F Shelf
900Sq & 1000Sq
End Panel Top Panel Base Panel Back Panel Diagonal Panel Shelf Back Panel End Panel
End Panel
G Back Panel
E
C
Diagonal Panel
Base Panel
B Top Panel
D Back Panel
A End Panel
150o
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball
Built Under Oven Unit
Leg Sockets
Legs
4
4
Cams
Steel Screws
18
!
Plinth Clips
22
2 18mm
W/Top Fix Blocks
Wood Dowels
Quickfit Bolts
14
18
Nickel Screws
2
600
16mm
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Cam
Quick Fit Bolt
Oven Shelf
Base Panel
End Panels (L.H. Shown)
Rails Dowel
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
Built Under Oven Unit
ASSEMBLE
TOOLS REQUIRED
COMPONENTS A B C D E F G
In alphabetical sequence
600
End Panel Base Panel Oven Shelf Front Rail Back Rail End Panel Shelf Bearers
R.H. End Panel
F
Back Rail Front Rail
D
E C Oven Shelf
B
Screw
A
Base Panel
L.H. End Panel Shelf Bearers
G
Blocks If back rail E is not used apply block for worktop fixing, positioned as required by fitters.
150o
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball Cover Caps
Hinge Plates
2
2
Pushfit Bolts
Wood Dowels
4
8
!
Single Base Units 300, 350, 400, 450, 500 & 600 Clip-on Hinges
2
Door Buffers
Shelf Supports
2
Cover Caps
5mm
20
Nickel Screws
16mm
Leg Sockets
Legs
4
4
4
W/Top Fix Blocks
Quickfit Bolts
Cams
2
8
12
8
Plinth Clips
2 Steel Screws
20
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Quick Fit Bolt Shelf Support Tandem Drawer
Cam
Push Fit Bolt Meta Box Drawer
Base Panel
End Panels (L.H. Shown)
Rails
715 Door OR 570 Door
Dowel
OR Hinge Plate
Door Buffer
To Handing as Required
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
18mm
William Ball
Single Base Units 300, 350, 400, 450, 500 & 600
ASSEMBLE
COMPONENTS
TOOLS REQUIRED
In alphabetical sequence
A B C D E F G
F
Base Panel Back Rail Back Panel Front Rail End Panel Legs
R.H. End Panel
C Back Rail
E
End Panel
D
Back Panel
Front Rail
A L.H. End Panel
B Base Panel
Blocks Worktop fixing block positioned close to back rail as required by fitters. 150o
90o
0o
G Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
IMPORTANT Flange must overhang gable end
WBU 691
C
William Ball Single Wall Units FITTINGS FOR 360, 575, 720 AND 900 Wood Dowels
Quickfit Bolts
Cam
Concealed Hanger
Joined Hanging Plate
Hanger Cover Caps
2
8
8
8
2
2
Clip-on Hinges
Cover Caps
Hinge Plates
Door Buffers
Nickel Screws
360 575 720 900
high high high High
600 (No Shelf) 300, 400, 450, 500 & 600 300, 350, 400, 450, 500 & 600 300, 400, 450, 500 & 600
360
575
720
900
Cover Caps
Cover Caps
Cover Caps
Cover Caps
5mm
5mm
5mm
5mm
0
12
8
16
Shelf Support
Shelf Support
Shelf Support
Shelf Support
0
4
8
8
16mm
2
!
2
2
2
4
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Cam Shelf Support
Top/Base Panels
Dowel
End Panel
Quick Fit Bolt Hinge Plate
OR
To Handing as Required
Door Buffer
Concealed Hanger
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball Single Wall Units ASSEMBLE
360 575 720 900
high high high High
TOOLS REQUIRED
600 (No Shelf) 300, 400, 450, 500 & 600 300, 350, 400, 450, 500 & 600 300, 400, 450, 500 & 600
COMPONENTS
In alphabetical sequence
A B C D E
360 575 720 900
End Panel
1
1
1
1
Base Panel
1
1
1
1
Top Panel
1
1
1
1
Back Panel
1
1
1
1
End Panel
1
1
1
1
Shelf
0
1
2
2
Cover Cap Cap hole after fitting
E
R.H. End Panel
C
D
Top Panel
Back Panel
B A
Base Panel L.H. End Panel
F 150o
Concealed Hanger Note pull down tab to lock hanger to cabinet
42
90o
Dual Fitting
0o 3mm 30mm 30mm
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
Side View
End of Run Fitting
WBU 691
C
William Ball 11
10
Cams
Cams
1400 1825 1970 2150
Tall Larder Unit 11 - 10
Legs
61
Leg Sockets
Hinge Plates
high high high high
30 - 50 - 60 - 61
30 - 50 - 60 Clip-on Hinges
Cover Caps 5mm
300 wide 500 wide 600 wide 1000 wide
Screws 16mm
Legs
Leg Sockets
16
22
6
6
4
4
56
14
4
4
Quickfit Bolts
Quickfit Bolts
Plinth Clips
Hinge Plates
Cover Caps
Door Buffers
Door Buffers
Clip-on Hinges
Plinth Clips
Cams
16
22
2
10
4
4
5
5
2
18
Wood Dowels
Wood Dowels
Clip-on Hinges
Cover Caps
Cover Caps 5mm
Cover Caps 8mm
Hinge Plates
Cover Caps
Quickfit Bolts
Wood Dowels
24
5
5
18
18
16
!
22
10
10
24
Cover Caps 5mm
Screws 18mm
Screws 16mm
Screws 16mm
Screws 18mm
40
24
24
12
16
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly Cam
Quick Fit Bolt
Base Panel (Top & Fixed Shelf Similar)
Dowel Shelf Support End Panel
OR Door Buffer
Rails
Hinge Plate
To Handing as Required
1000mm Wide Only
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
1400 1825 1970 2150
Tall Larder Unit
ASSEMBLE
COMPONENTS FOR SINGLE
TOOLS REQUIRED
A B C D E F G
In alphabetical sequence
G
high high high high
End Panel L.H. Base Panel Fixed Shelf Large Back Top Panel Small Back End Panel R.H.
300 wide 500 wide 600 wide 1000 wide
61 60 50 30 1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
R.H. End Panel
Small Back
F
E Top Panel
C Fixed Shelf Cams to underside of fixed shelf to suit application required
D
Large Back
B COMPONENTS FOR DOUBLE
A B C D E F G H I
End Panel L.H. Base Panel Fixed Shelf Top Panel Back Rail Large Back H Section Large Back End Panel R.H.
A
11 10 1 1 1 1 2 1 1
1 1 1 1 2 1 1
1
1
1
1
Base Panel
L.H. End Panel
IMPORTANT Flange must overhang gable end 150o
90o
I
0o
R.H. End Panel
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
H D Top Panel
Large Back
C Fixed Shelf Cams to underside of fixed shelf to suit application required
LA10 ONLY
F Large Back
E Back Rail
B A Inside Face
Base Panel L.H. End Panel
G H Section
WBU 691
C
William Ball Leg Sockets
Tall Oven & Fridge
Legs
Plinth Clips
4
4
2
Wood Dowels
Door Buffers
Shelf Supports
24
4
4
!
2150 high 1970 high 1825 High
Hinge Plates
Clip-on Hinges
4
4
Steel Screws
18mm
22
Nickel Screws
Cover Caps
Cams
4 16mm
8
Quickfit Bolts
24
Cover Caps
24
Cover Caps
5mm
32
600 600 600
8mm
48
To avoid damage, work on a clean, flat surface (use inside face of carton). The manufacturers will not accept responsibility for damage caused during assembly or use.
PREPARATION
Apply all fittings shown below before assembly
Cam
Quick Fit Bolt
Top Panel (Base, oven & fixed shelves similar) TO
TH TK
TI TG R E V E R S E
TF TG TE
TC
TF
TE
TC TK TH TP
TB
175 TE
355
TJ
Dowel TH TK TP
TB
495
495
355
715
495 980
570 895 980
980 895
715
715
715
570
570
570
355
175
End Panels L.H. Shown
2150 High
1970 High
1825 High
THE USE OF SUBSTITUTE PARTS ARE NOT RECOMMENDED
William Ball
2150 high 1970 high 1825 High
Tall Oven & Fridge
ASSEMBLE
600 600 600
COMPONENTS
In alphabetical sequence
A C E G
TOOLS REQUIRED
End Panel L.H. Oven Shelf Top Panel Back Panel
B D F H
Base Panel Back Panel Fixed Shelf End Panel R.H. Loose Shelf
Shelf Bearers
H
R.H. End Panel
G Back Panel
E Top Panel
D
F
Back Panel
Fixed Shelf
C A
Oven Shelf
B
L.H. End Panel
Base Panel
Plastic Support Strip
150o
IMPORTANT Flange must overhang gable end
90o
0o
Cam Locking Details To lock cam, turn clockwise through 150o using either size 3 posidriver, 6 x 1.5 flat tip driver or SW4 allen key (Do not attempt to turn beyond 180o)
WBU 691
C