AILURE T O FOLLOW DANGER, W ARNING, AND CAUTION MESSAGES COULD RESUL T DEA SERIOUS INJUR Y .

Machine safety

NOTICE: Notice indicates a situation that, not avoided, could result machine property damage.

Throughout this manual you will find the signal word Notice followed special instructions prevent machine property damage. The word Notice used address practices not related personal safety .

Information

NOTE: Note indicates additional information that clarifies other information this

Throughout this manual you will find the word Note followed additional information about a step, other information the The word Note not intended address personal safety property

Safety rules - Personal safety

Carefully study these precautions, and those included the external attachment operators manual, and insist that they followed those working with and for you.

Thoroughly read and understand this manual and the attachment Operator ’ s Manual before operating this any other

Be sure all people and pets are clear the machine before starting. Sound the horn, equipped, three times before starting

Only the operator should the machine when Never allow anyone climb the machine while the machine equipped with Instructors this must only used for training Passengers must not allowed use the Instructors

Keep all shields place. Never work around the machine any the attachments while wearing loose clothing that might catch moving

Observe the following precautions whenever lubricating the machine making adjustments.

• Disengage all clutching levers

• Lower the attachment, equipped, the ground raise the attachment completely and engage the cylinder safety Completing these actions will prevent the attachment from lowering unexpectedly

• Engage the parking brake.

• Shut f the engine and remove the key

• W ait for all machine movement stop before leaving the operators

Always keep the machine gear while travelling

The machine should always equipped with suf ficient front rear axle weight for safe

Under some field more weight may required the front rear axle for adequate stability This especially important when operating hilly conditions / when using heavy

Always lower the shut f the set the parking engage the transmission remove the key and wait for all machine movement stop before leaving the operators

10. the attachment machine should become obstructed plugged; set the parking brake, shut f the engine and remove the key , engage the transmission wait for all machine attachment motion come a before leaving the operators platform removing the obstruction

1 Never disconnect make any adjustments the hydraulic system unless the machine and / the attachment lowered the ground the safety lock(s) the engaged

Use the flashing lights highly recommended when operating a public

When transporting a road highway , use accessory lights and devices for adequate warning the tors other vehicles. this regard, check local government regulations. V arious safety lights and devices are available from your CASE CONSTRUCTION dealer

Practice safety 365 days a year

Keep all your equipment safe operating

Keep all guards and safety devices

Always set the parking shut f the engine and remove the key , engage the transmission wait for all machine attachment motion come a before leaving the operators platform service the machine and attachment.

Remember: A careful operator the best insurance against

19. Extreme care should taken keeping hands and clothing away from moving parts.

Basic instructions - Loader arm lock and cab tilt procedure - radial lift machines

SR210 TIER (FINAL) [NGM418237 - ]

SR210 TIER (FINAL) [NHM435463 - ]

SR240 TIER (FINAL) [NGM418237 - ]

SR240 TIER (FINAL) [NHM435463 - ]

TR270 TIER (FINAL) [NGM418237 - ]

TR270 TIER (FINAL) [NHM435463 - ]

TR310 TIER (FINAL) [NGM418237 - ]

TR310 TIER (FINAL) [NHM435463 - ]

Danger

Crushing hazard! not enter exit the compartment while the loader arms are raised Rest the loader arms the ground verify that loader arm being supported the loader arm strut loader arm lock pin before entering exiting the compartment. Failure comply will result death serious injury .

W Arning

Crushing hazard! Loader arms are unsupported during support strut removal. not enter exit the compartment with unsupported loader T persons are required during storage. One person should remove and store the support strut while the operator remains the Failure comply could result death serious injury .

Raise and lock the loader arm for machine service

NOTE: An instructional decal the inside the righthand loader just above the support strut also Understand the loader arm lock procedure before continuing.

Sit the fasten the seat pull down the restraint bar and start the Press the OPERA button enable the Remove the bucket attachment from the mounting

Park the machine firm and level assistant not turn f the engine and exit the

Remove the support strut pin (A) and let the support strut (B) rest the lift cylinder barrel (C)

Slowly raise the loader arm until the support strut (B) falls onto the cylinder rod (D) .

Stop the

Pull the override control knob (red control knob near the right - hand side the operator ’ s The support strut (B) will brace against the top the der barrel (C)

Ask assistant insert the pin (A) into the support strut (B) . assistant not available visually firm that the support strut braced against the top the cylinder barrel before exiting the

T ilt and lock the cab forward for machine service

Remove the two, rear retaining nuts, located the rear the

Pull the hand holds the front the machine until the cab completely tilted forward.

Confirm that the red lock tube has lowered over the cab pivot linkage. has the cab tilt position now

T ilt and secure the cab for machine operation

Raise the red lock tube exposing the cab pivot

Push the cab backward into the operation

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING

NOTE:

If there is no response to click on the link above, please download the PDF document first and then clickonit.

Unlock and lower the loader arm for machine operation W ARNING

Crushing hazard! Loader arms are ported during support strut removal. not enter exit the ment with unsupported loader T persons are required during storage. One person should remove and store the support strut while the operator remains the compartment.

Failure comply could result death serious injury .

W0077B

NOTE: An instructional decal the inside the righthand loader just above the support strut also Understand the loader arm unlock procedure before

Placing the support strut the storage position requires a second The operator must remain the seat during this

Sit the fasten the seat pull down the restraint bar and start the Press the operate button enable the Raise the loader arm until the support strut (B) not resting the end the cylinder barrel (C) .

Instruct the second person remove the support strut pin (A) and place the support strut the stowed sition and reinstall the support strut pin (A) When the second person has cleared the the operator may now lower the loader arm.

Commence work operations park the machine and stop the

Basic instructions - Loader arm lock and cab tilt procedurevertical lift machines

SV280 TIER (FINAL) [NGM418237 - ]

SV280 TIER (FINAL) [NHM435463 - ]

TV370 TIER (FINAL) [NHM435463 - ]

W Arning

Crushing hazard! not enter exit the compartment while the loader arms are raised Rest the loader arms the ground verify that loader arm being supported the loader arm strut loader arm lock pin before entering exiting the Failure comply could result death serious injury .

Raise and lock the loader arm for machine service

Sit the fasten the seat pull down the restraint bar and start the

Press the operate button enable the Remove the bucket attachment from the mounting

Park the machine a level surface.

Fully raise the loader arm.

Locate the loader arm lock lever the left - hand side the operator ’ s seat.

Rotate the lock lever toward the operator ’ s seat (clockwise) engage the lock support Stop the

Pull the override control knob (red control knob near the right - hand side the operator ’ s The loader will brace against the lock support pin and keep the loader arm a raised

NOTE: Only use the override control knob lower the loader arm emergency situations when engine power not available lower onto the lock support pin for servicing the

T ilt and lock the cab forward for machine service

Remove the rear retaining located the rear the

Pull the hand holds the front the machine until the cab completely tilted forward.

Confirm that the red lock tube has lowered over the cab pivot has the cab tilt position now

T ilt and secure the cab for machine operation

Raise the red lock tube exposing the cab pivot Push the cab backward into the operation position. RAPH12SSL0420BA