SERVICE

Part number 48012910

English May 2016

Connecting rods and pistons

Crankshaft and flywheel

Fuel injection system Engine cooling system

Fan and drive

Drive shaft Front axle system

Powered front axle .

Front bevel gear set and dif

Final drive steering and shafts

Rear axle system

Powered rear axle

Rear bevel gear set and dif

Safety rules

Pay attention this symbol

This warning symbol points out important messages involving personal safety . Carefully read the safety rules contained herein and follow advised precautions avoid potential hazards and safeguard your safety and personal integrity this manual you will find this symbol together with the following

W ARNING: gives warning about improper repair operations and potential consequences fecting the service s personal safety

DANGER: gives specific warning about potential dangers for personal safety the operator other persons directly indirectly involved the

T o prevent accidents

Most accidents and personal injuries taking place workshops are due from non - observance some simple and essential prudential rule and safety

For this most cases they can suf fices foresee possible causes and act consequently with necessary caution and

The possibility that accident might occur with any type machines should not matter how well the machine question was designed and

A wise and careful service technician the best precautions against Careful observance this only basic precaution would enough avoid many severe

Danger

Never carry out any lubrication maintenance operations when the engine

General

Carefully follow specified repair and maintenance

• not wear wrist jewelry , unbuttoned loose articles clothing such as: torn open jackets shirts with open zips which may remain entangled moving W e advise use approved safety clothing such anti - slipping footwear , gloves, safety goggles, helmets, etc.

• Never carry out any repair the machine someone sitting the operator ’ s except they are certified operators assist the operation carried out.

• Never operate the machine use attachments from a place other than sitting the operator ’ s

• Never carry out any operation the machine when the engine except when specifically

• Stop the engine and ensure that all pressure relieved from hydraulic circuits before removing

• All repair and maintenance operations must carried out using extreme care and

• Service steps and platforms used a workshop the field should built compliance with the safety rules force.

• Disconnect the batteries and label all controls indicate that the vehicle being Block the machine and all equipment which should raised.

• Never check fill fuel tanks nor use starting liquid you are smoking near open flames such fluids are

• Brakes are inoperative when they are manually released for maintenance such the machine should kept constantly under control using blocks similar

• The fuel filling gun should always remain contact with the filler Maintain this contact until the fuel stops flowing into the tank avoid possible sparks due static electricity build -

• Use exclusively specified towing points for towing the tractor Connect parts carefully Ensure that foreseen pins and / locks are steadily fixed before applying not stop near towing cables chains working under load.

• T o transfer a failed tractor , use a trailer a low loading platform trolley

• T o load and unload the machine from the transportation means, select a flat area providing a firm support the trailer truck Firmly tie the machine the truck trailer platform and block wheels required the forwarder

• For electrical battery - chargers and similar equipment use exclusive auxiliary power supplies with a ficient ground avoid electrical shock

• Always use lifting equipment appropriate capacity lift move heavy

• Pay special attention

• Never pour gasoline diesel oil into open, wide and low containers.

• Never use diesel oil other inflammable liquids cleaning Use non - flammable non - toxic proprietary solvents.

• W ear safety glasses with side guards when cleaning parts using compressed air

• not exceed a pressure bar , accordance with local

• not run the engine a closed building without proper

• not use naked cause sparks the area when fuel filling handling highly inflammable

• not use flames light sources when working a machine checking for

• Move with caution when working under a tractor , and also near a tractor W ear proper safety accessories: goggles and special footwear

• During checks which should carried out with the engine ask assistant seat the operator ’ s seat and keep the service technician under visual control any moment.

• case operations outside the drive the tractor a flat area and block working incline cannot first block the tractor carefully Move a flat area soon possible with a certain extent safety

• Ruined plied cables and chains are not use them for lifting Always handle them wearing gloves proper

• Chains should always safely Ensure that fastening device strong enough hold the load persons should stop near the fastening point, trailing chains cables.

• The working area should always kept CLEAN and Y Immediately clean any spillage water

• not pile grease oil soaked rags, they constitute a great fire hazard. Always place them into a metal container

Before starting the tractor its adjust and block the operator ’ s Also ensure that there are persons within the tractor attachment operating range.

• not keep your pockets any object which might fall unobserved into the tractor ’ s inner

• Whenever there the possibility being reached ejected metal parts similar , use protection eye mask goggles with side special footwear and heavy

• W ear suitable protection such tinted eye special gloves and footwear whenever necessary carry out welding All persons standing the vicinity the welding process should wear tinted eye NEVER LOOK A T THE WELDING ARC YOUR EYES ARE NOT SUIT ABL Y

• Metal cables with the use get Always wear adequate protections (heavy eye

• Handle all parts with the greatest Keep your hands and fingers far from moving gears and similar Always use approved protective equipment, such eye protection, heavy gloves and protective footwear .

Start

• Never run the engine confined spaces that are not equipped with adequate ventilation for exhaust gas extraction.

• Never place the body , hands fingers near fans rotating

48012910 23/08/2016

Engine - Sectional view

Longitudinal section 3 cylinder engine

Engine - Engine and crankcase

Engine - Sectional view

Cross section 3 cylinder engine

Engine - Sectional view

ANIL15TRO0029HB 1 Lubrication system 3 cylinder engine

F Filter Suction screen

Oil pressure gage T . Oil fill cover

Oil dipstick V Pressure bypass valve

P Pump Filter bypass valve

48012910 23/08/2016

Thermostat open

ANIL15TRO0030GB 2

Engine cooling system

W ater temperature gage

Thermostat closed Engine coolant temperature sender

3 - cylinder models Fan

Thermostat Radiator Pump