New Holland TD5.115 Tractor Service Repair Manual by u1yiuef6

English

May 2016

SERVICE MANUAL

TD5.85 / TD5.95 / TD5.105 / TD5.115

Tractor

Part number 48013235

SER VICE MANUAL TD5.105 TD5.1 TD5.85 TD5.95 48013235 19/09/2016

[25.400] Non-powered front axle .

Rear axle system

Powered rear axle

Rear bevel gear set and dif ferential

Final drive steering and shafts

Rear mechanical control

Contents INTRODUCTION Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [10.501] Exhaust Gas Recirculation (EGR) exhaust treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [18.1 10] Clutch and components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.1 T ransmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14] Mechanical transmission [21.140] Mechanical transmission internal components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.2 [21.1 12] Power shuttle transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.3 [21.154] Power shuttle transmission internal components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.4 [21.120] Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.5 [21.160] Creeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.6 [21.162] Reverser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.7 Four-Wheel Drive (4WD) system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [23.202] Electro-hydraulic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1 Front axle system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Powered front axle Front bevel gear set and dif ferential [25.108] Final drive hub, steering knuckles, and shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.4

. .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

T ake-Of f (PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.1 48013235 19/09/2016

Power

[31.101]

service brakes

brake pneumatic control

Harnesses and connectors

Cab engine controls

Engine control system

Engine starting system Alternator

Battery

Cold start aid

Fuel tank system

Fuel injection system

Brakes and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [33.202] Hydraulic

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.1 [33.220] T

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.2 [33.224] T

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.3 Hydraulic

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic systems Fixed displacement pump

hydraulic valves and lines Main lift system Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [41.200] Hydraulic control components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.1 [41.206] Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.2 [41.216] Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.3 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front wheels Cab climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [50.200] Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.1 Electrical systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

system

railer brake hydraulic control

railer

systems

Auxiliary

Electrical

48013235 19/09/2016

Engine intake and exhaust system 1 Engine oil system Electronic modules T ransmission control system Rear Power T f (PT control system Front Power T f (PT control system [55.512] Cab controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.17 [55.130] Rear hitch electronic control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.18 [55.408] W arning indicators, alarms, and instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.19 Platform, cab, bodywork, and decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cab 48013235 19/09/2016

INTRODUCTION 48013235 19/09/2016 1

Contents INTRODUCTION Note the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 48013235 19/09/2016 2

Note the Owner

General instructions

Important notice

All maintenance and repair operations described this manual should carried out exclusively the NEW LAND authorised All instructions detailed should carefully observed and special equipment indicated should used necessary

Everyone who carries out service operations described without carefully observing these prescriptions will directly responsible deriving

Shimming

each select adjusting measure them individually using a micrometer and then sum recorded values. not rely measuring the whole shimming set, which may incorrect, rated value indicated for each

Rotating shaft seals

T o correctly install rotating shaft observe the following instructions:

• Let the seal soak into the same oil will seal for least half hour before mounting.

• Thoroughly clean the shaft and ensure that the shaft working surface not

• Place the sealing lip towards the case a hydrodynamic consider the shaft rotation direction and orient grooves order that they deviate the fluid towards the inner side the

• Coat the sealing lip with a thin layer lubricant (oil rather than grease) and fill with grease the gap between the sealing lip and the dust lip double lip

• Insert the seal into its seat and press down using a flat tap the seal with a hammer a

• T ake care insert the seal perpendicularly its seat while you are pressing it. Once the seal settled, ensure that contacts the thrust element

• T o prevent damaging the sealing lip against the shaft, place a suitable protection during installation.

O - rings

Lubricate the O - rings before inserting them into their seats. This will prevent the O - rings from rolling over and twine during mounting which will jeopardise

Sealers

Apply one the following sealers: R SILMA RHODORSIL CAF 1 , L OCTITE ® P IASTIC G ASKET over the mating surfaces marked with

Before applying the sealer , prepare the surface follows:

• Remove possible scales using a metal

• Thoroughly degrease the surfaces using one the following cleaning agent: petrol a water and soda

Bearings

advisable heat the bearings - ( 176 - 194 ) before mounting them their shafts and cool them down before inserting them into their seats with external tapping.

Roll pins

When fitting straight roll pins, ensure that the pin notch oriented the direction the fort stress the pin. Coil roll pins can installed any

INTRODUCTION

48013235 19/09/2016 3

• T o transfer a failed tractor , use a trailer a low loading platform trolley

• T o load and unload the machine from the transportation select a flat area providing a firm support the trailer truck Firmly tie the machine the truck trailer platform and block wheels required the forwarder

• For electrical battery - chargers and similar equipment use exclusive auxiliary power supplies with a ficient ground avoid electrical shock

• Always use lifting equipment and similar appropriate capacity lift move heavy components.

• Pay special attention

• Never pour gasoline diesel oil into open, wide and low containers.

• Never use diesel oil other flammable liquids cleaning Use nonflammable nontoxic etary

• W ear protection goggles with side guards when cleaning parts using compressed air

• not exceed a pressure 2.1 bar ( 30.45 psi ) , accordance with local

• not run the engine a closed building without proper

• not use open cause sparks the nearby area when filling fuel handling highly flammable liquids.

• not use flames light sources when working a machine checking for

• Move with caution when working under a tractor , and also near a tractor . W ear proper safety accessories: goggles and special footwear

• During checks which should carried out with the engine ask assistant seat the operator ’ s seat and keep the service technician under visual control any

• case operations outside the drive the tractor a flat area and block working incline cannot first block the tractor carefully Move a flat area soon possible with a certain extent safety

• Ruined plied cables and chains are unreliable. not use them for lifting trailing. Always handle them wearing gloves proper

• Chains should always safely Ensure that fastening device strong enough hold the load persons should stop near the fastening trailing chains

• The working area should always kept CLEAN and Y Immediately clean any spillage water

• not pile grease oil soaked they constitute a great fire Always place them into a metal container Before starting the tractor its adjust and block the operator ’ s Also ensure that there are persons within the tractor attachment operating range.

• not keep into your pockets any object which might fall unobserved into the tractor ’ s inner

• Whenever there the possibility being reached ejected metal parts similar , use protection eye mask goggles with side special footwear and heavy

• W ear suitable protection such tinted eye special gloves and footwear whenever necessary carry out welding All persons standing the vicinity the welding process should wear tinted eye NEVER LOOK A T THE WELDING ARC YOUR EYES ARE NOT SUIT ABL Y

• Metal cables with the use get frayed. Always wear adequate protections (heavy gloves, eye protection, etc.)

• Handle all parts with the greatest Keep your hands and fingers far from moving gears and similar Always use approved protective such eye heavy gloves and protective footwear

Start

• Never run the engine confined spaces which are not equipped with adequate ventilation for exhaust gas

• Never bring your body , fingers near fans rotating 48013235 19/09/2016

INTRODUCTION

SER VICE MANUAL Engine TD5.105 TD5.1 TD5.85 TD5.95 48013235 19/09/2016

Contents EngineExhaust Gas Recirculation (EGR) exhaust treatment 48013235 19/09/2016

EngineExhaust Gas Recirculation (EGR) exhaust treatment - 501 TD5.105 TD5.1 TD5.85 TD5.95 48013235 19/09/2016 10.1 [10.501] / 1

Contents EngineExhaust Gas Recirculation (EGR) exhaust treatment - 501 TECHNICAL T A Diesel Particulate Filters (DPF) T orque 3 General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FUNCTIONAL T A Diesel Particulate Filters (DPF) Dynamic description 6 SER VICE Diesel Particulate Filters (DPF) Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Install Remove - with support DIAGNOSTIC Exhaust Gas Recirculation (EGR) exhaust treatment 3710 - Lambda sensor - signal not plausible [ECU] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3766 - Diesel particulate filter pressure sensor: Fault check for the pressure sensor plausibility 3796 - Diesel particulate filter pressure sensor hose line error 3825 - Short circuit over load error for H - bridge [ECU] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48013235 19/09/2016 10.1 [10.501] / 2

Diesel Particulate Filters (DPF) - T orque

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO1984FB 1 Part tighten Thread size T orque settings Gas temperature sensor DPF intake M14 x 1.5 - N·m ( 29.8736.51 )( 9.13 - 1 1.29 ) DPF filter first section temperature sensor M14 x - N·m ( 29.8736.51 )( 9.13 - 1 1.29 ) Pressure pipe fitting turbine side M14 x 40.5049.50 N·m ( 29.8736.51 ) 4.145.12 ( 9.13 - 1 1.29 ) Pressure pipe fitting muf fler side M12 x 27.0033.00 ( - ) 2.803.42 ( - ) Lambda sensor M18 x 1.5 - N·m ( 33.1940.57 )( 10.2712.57 ) Air temperature sensor M12 x - N·m ( 1 1.0618.44 )( 3.425.71 ) 48013235 19/09/2016 10.1 [10.501] / 3

Diesel Particulate Filters (DPF) - General specification

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO1985HB 1 Measurements respect for installing the filter - Legend components - Legend sensor fixing holes: 48013235 19/09/2016 10.1 [10.501] / 4

- ( - ) Distance between the two bands the the one with the set fixing holes (10) and the one with the adjustable fixing holes

- ( - ) Distance between the centre the turbine the centre the union the decoupler / turbine and the adjustable filter fixing bushings (12)

134 - ( 5 - ) Distance between the centre the turbine the centre the union / turbine and the band supporting surface (4) with set fixing holes the filter

Band supporting surface with set fixing holes.

Initial part the DPF filter , connected with the sleeve (15) the Middle part the DPF filter , inside which there the ceramic part clean.

End part the DPF filter , connected with the sleeve (14) the exhaust

Clamp retaining the middle part (6) \ end part (7)

Clamp retaining the middle part (6) \ initial part (5)

Band with the set fixing

1 Band with the adjustable fixing

Threaded screwing them out enables changing the adjustment distance (3)

Grub screw fixing the bushing (12)

Filter outlet inserted the exhaust

Union joining the filter the

Clamp fixing the union (15) the filter

T utor , protects the decoupler during the handling from the supplier , dismantled after assembly (it advised keep one hand and reassemble before starting disassemble the filter that the decoupler undergoes deformation).

Gas pressure detection after the middle part the filter , the pipe that goes the dif ferential pressure sensor connected

Gas pressure detection before the middle part the filter , the pipe that goes the dif ferential pressure sensor connected

Exhaust gas temperature sensor from the Exhaust gas temperature sensor the intake the middle part the filter

22. Lambda sensor .

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

48013235 19/09/2016 10.1 [10.501] / 5

Diesel Particulate Filters (DPF) - Dynamic description

A diesel particulate filter (DPF) a device designed remove polluting diesel engine particulate from exhaust gas when needs

The diesel particulate filter can regenerated automatically forcing.

The regeneration process signaled the operator the central monitor the dashboard and with acoustic The indication necessary for the purposes safety warn the operator about the high exhaust temperature reached during the

The automatic regeneration shall not fect engine

During the the operator can continue working normally

Under certain operating conditions automatic regeneration might not completed (engine continuously stopping and lengthy periods idle speed) and must then

The start automatic highlighted with the following warning light blinking the dashboard and the same symbol appears every 5 minutes the central monitor with the word “ON” combined with a single concluding the operation the symbol appears with the word “OFF“.

When the level soot exceeds a certain the electronic control unit asks you proceed with manual filter regeneration.

NOTICE: the filter not regenerated when whether manually the functionality the filter Continuing ignore this besides greatly reducing engine horsepower , damages the filter such extent that necessary for the dealer replace the filter with a new one.

When the following warnings appear the dashboard necessary proceed follows:

DPF regenerated

Start automatic regeneration with the control, start forced regeneration

Image legend:

W arning light the dashboard

Flasher

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

48013235 19/09/2016 10.1 [10.501] / 6

f Central display ANIL15TRO1986AA 1

DPF regenerated Low severity

Automatic regeneration only start forced generation with control

ANIL15TRO1987AA 2

DPF regenerated High severity

Automatic regeneration only start forced generation with control

DPF damaged technical support required

Automatic and forced regeneration inhibited

ANIL15TRO1988AA 3

ANIL15TRO1989AA 4

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

48013235 19/09/2016 10.1 [10.501] / 7

Diesel Particulate Filters (DPF) - Remove

Raise the disconnect the headlights connector from the engine Remove the See T railer brake pneumatic control - Remove NOTE: Remove the hinge from the support leaving this under the

Remove the side panels both

Loosen the clamp the connection pipe (1) between the air cleaner (3) and unscrew the retaining screws the air intake pipe (2) then slide towards the front that comes out the filter ter disconnecting the clogged filter sensor remove the filter from the bonnet

Disconnect the connectors the pressure dif ferential sensor (1) , the two temperature and the lambda sensor Loosen the system heat shield (2) Position everything the left - hand side the

Remove the bonnet support (1) .

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO1943AB

ANIL15TRO2012AB 2

ANIL15TRO2016AB 3

ANIL15TRO2010AB 4 48013235 19/09/2016 10.1 [10.501] / 1 1

Unscrew the pressure dif ferential unit (1) with its pipes, clamps and sensor

Unscrew the temperature sensor (2)

Unscrew the filter ’ s upper heat shield (1) , the lower one stays

Mark the filter shown the

NOTE: The right - hand marking must include the first part the filter , the central part the filter (1) , and the clamp that joins them (2) The left - hand marking will include the central the left - hand and the clamp (3)

Loosen the clamp (1) joining the muf fler the DPF outlet The clamp (2) that keeps the outlet tube the filter parallel the first section the filter

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO1996AB 5

ANIL15TRO1997AB 6

ANIL15TRO1998AB 7

ANIL15TRO1999AB 8 48013235 19/09/2016 10.1 [10.501] /

1 Remove the left - hand clamp (1) fastening the filter the

12. Loosen the left - hand clamp (1) fastening the middle and left parts the filter

Remove the left - hand part the filter (1) , with the clamp (2) , retrieving the copper

after you have loosened the right - hand clamp (1) , remove the central part the filter (2)

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2000AB 9

ANIL15TRO2001AB

ANIL15TRO2002AB 1 1

ANIL15TRO2003AB 48013235 19/09/2016 10.1 [10.501] /

Diesel Particulate Filters (DPF) - Install

NOTE: For the torque settings please refer Diesel Particulate Filters (DPF) - T orque (10.501)

- assemble the central part the DPF filter (2) with the relevant T ighten the clamp (1) , paying tention the orientation the

- assemble the left - hand part the DPF filter (1) with the relevant clamp (2) T ighten the paying tion the orientation the parts.

NOTE: the clamp and the seal are rusty a poor change the clamp and the

Reassemble the left - hand clamp (1) fastening the filter the

Position the collar (1) fastening the filter pipe the muf fler T ighten Also tighten the top the collar (2) that fixes the pipe the

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2003AB 1

ANIL15TRO2005AB 2

ANIL15TRO2006AB 3

ANIL15TRO2007AB 4 48013235 19/09/2016 10.1 [10.501] /

- fit the filter upper heat shield (1) .

- fit the temperature sensor (2) and the pressure ferential assembly (1) , complete with and sensor

Refit the hood support (1)

Refit the system heat shield (2) Reconnect the sure sensor , lambda sensor , and pressure dif ferential sensor (1) Position the wire necessary , secure the wire harness with straps.

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2008AB 5

ANIL15TRO2009AB 6

ANIL15TRO2010AB 7

ANIL15TRO201 1AB 8 48013235 19/09/2016 10.1 [10.501] /

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING

NOTE:

If there is no response to click on the link above, please download the PDF document first and then clickonit.

Fit the air cleaner (3) onto the hose (1) that connects the air cleaner the Then secure the hose the hood support with the relevant

10. T ighten the clamp the hose. Run the intake duct (2) toward the filter Then tighten with the relevant Reconnect the connector the clogged filter sensor

1 - assemble the side panels (2) and the bonnet (1) , T railer brake pneumatic control - Install

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2012AB 9

48013235 19/09/2016 10.1 [10.501] /

Diesel Particulate Filters (DPF) - Remove - with support

Raise the Disconnect the headlight connector from the engine after you have secured the hood the hoist with a remove the See T railer brake pneumatic control - Remove (33.224) Remove the side panels both

With the controller for recovering the gas from the airconditioning recover the gas (1)

Disconnect the air conditioning pipes (1) , the control panel side.

Loosen the clamp (1) retaining the air cleaner / turbine connection Loosen the bolts the air intake pipe (2) Then slide the pipe toward the front make the pipe come out the air cleaner

Disconnect the connector the clogged filter sensor , unscrew the filter (3) from the hood support and extract

Disconnect the connectors the pressure dif ferential sensor (1) , the two temperature and the lambda sensor Loosen the system heat shield (2) Position everything the left - hand side the engine.

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2013AB 1

ANIL15TRO2014AB 2

ANIL15TRO2015AB 3

ANIL15TRO2016AB 4 48013235 19/09/2016 10.1 [10.501] /

Remove the complete hood support (1) .

the gap the left - hand side the reservoir for the behind the filter , remove the bolts (1) that join the cross support (2) the filter and the rear support (3)

Remove the brakes reservoir heat shield (1)

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2017AB 5

ANIL15TRO2018AB 6

ANIL15TRO2019AB 7

ANIL15TRO2020AB 8 48013235 19/09/2016 10.1 [10.501] /

1 Loosen the clamp (1) fastening the exhaust pipe the DPF filter

12. Using a belt, sling the muf fler , two points least, take the slack with a Remove the bolts (2) that secure the exhaust pipe (1) the support (3) Then extract all the pipe from the right - hand side the tractor and put down a pallet the

13. Put two eyebolts (1) the screws retaining the upper heat shield the filter Using a hook the filter (2) and tension the

the left - hand under the filter remove the two screws (1) the adjustment bushings (3) the filter left support (2)

NOTE: After taking out the unscrew the bushings create a gap between the filter assembly and the left

the right - hand

loosen the clamp (1) that secures the filter decoupler the Move the clamp toward the T ake out the three hex socket screws (2) fastening the right support (3) the transversal

NOTE: These screws have been fitted the supplier and a few drops Loctite have been used prevent over from coming

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

ANIL15TRO2021AB 9

ANIL15TRO2022AB

ANIL15TRO2023AB 1 1

ANIL15TRO2024AB 48013235 19/09/2016 10.1 [10.501] /

16. Using the hoist, raise the filter , taking great care that there are wiring harnesses and tie - - rods connected obstructing the then rest the filter with the cross support a

NOTE: W ith the machine these conditions ble work the for example the valve cover , the right - hand support not possible reassemble the filter without making any special adjust-

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment

48013235 19/09/2016 10.1 [10.501] /