NEWCO Cast Steel Valves by Westlund PVF

NEWCO速 Cast Steel Valves Technical Data

TC9308-3

All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures or instructions, either expressed or implied, is forbidden without the written permission of Cameron or its authorized agent.

Initial Release 01 October 2013

Produced by Technical Publications, Houston, TX, USA ÂŠ 2013 Cameron TC9308-3

PREFACE The procedures included in this book are to be performed in conjunction with the requirements and recommendations outlined in API Specifications. Any repairs to the equipment covered by this book should be done by an authorized Cameron service representative. Cameron will not be responsible for loss or expense resulting from any failure of equipment or any damage to any property or death or injury to any person resulting in whole or in part from repairs performed by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve to terminate any contractual or other warranty, if any, on the equipment and may also result in equipment no longer meeting applicable requirements. File copies of this manual are maintained. Revisions and/or additions will be made as deemed necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions shown are accurate. This book covers Cameron products.

Cameron P.O. Box 1212 Houston, Texas 77251-1212 713-939-2211 http://www.c-a-m.com

TC9308-3

NOTES:

TC9308-3

TABLE OF CONTENTS Overview..............................................................................................................................7 I.

Cast Steel Bolted Bonnet Gate Valves.......................................................................18 Sizes: 2” to 48” • Pressure Class: 150 to 1500

II.

Cast Steel Bolted Bonnet Globe Valves.....................................................................30 Sizes: 2” to 14” • Pressure Class: 150 to 1500

III.

Cast Steel Bolted Bonnet Angle Valves.....................................................................42 Sizes: 2” to 12” • Pressure Class: 150 to 600

IV. Cast Steel Bolted Cover Swing Check Valves............................................................50 Sizes: 2” to 24” • Pressure Class: 150 to 1500 V.

Cast Steel Bolted Cover Tilting Disc Check Valves....................................................62 Sizes: 2” to 12” • Pressure Class: 150 to 300 (Pressure Seal 600 to 2500)

VI. Cast Steel Bolted Bonnet Stop Check Valves............................................................68 Sizes: 2” to 14” • Pressure Class: 150 to 1500 VII. Cast Steel Bolted Bonnet Angle Stop Check Valves.................................................80 Sizes: 2” to 12” • Pressure Class: 150 to 600 VIII. How to Order All Cameron’s NEWCO Products........................................................88 IX. Industry Standards Typically Used in Valve Manufacturing.....................................90

TC9308-3

NOTES:

TC9308-3

OVERVIEW Valve and I.D. Tag Overview The identification tag displays all construction and tracking data regarding the respective valve on which it is attached. Below is a general overview of the identification tag components. I.D. tags are located in 1 of the 3 following areas: • Yoke • Body/Bonnet Flange • Under The Handwheel Nut

I.D. Tag Locations Heat No.

Pressure Temperature Rating Trim Description Model C5/CR13, CR13, HF FIG. 13F-C5/2

750 PSI @ 100 °F

B16.34 CLASS 300 API 600/ISO10434

NPS 2 S/N 100419

NEWCO 6 300 WCB 77 T5158

Pressure Class

Nominal Port Size Serial Number

TC9308-3

Brand Size Pressure Class Body Material Pattern Heat No.

Body/Bonnet Materials Cameron’s NEWCO® cast steel valves are available in stock in a wide range of body/bonnet materials and optional trim materials. Listed below are some of the more popular materials. Additional materials are available. Please contact Cameron or your local distributor for details. Material Designation

Common Description

ASTM Specs.

Body/Bonnet Material Service Limitations*

Carbon Steel

A216

Non-corrosive service water, oil and gases at temperatures between -20º F and +800º F.

LCC

Low Temp. Carbon

A352

Low temperature service between -50º F and +650º F.

WC6

1.25% Chrome and .5% Moly

A217

Non-corrosive service water, oil and gases at temperatures between -20º F and +1100º F.

WC9

2.25% Chrome and 1% Moly

A217

Non-corrosive service water, oil, and gases at temperatures between -20º F and +1100º F.

5% Chrome and .5% Moly

A217

Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F.

C12

9% Chrome and 1% Moly

A217

Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F.

C12A

9% Chrome, 1% Moly and V

A217

Corrosive, non-corrosive or erosive service at temperatures between -20º F and +1200º F.

C8M

Cast 316

A351

Corrosive, cryogenic or high temperature service between -450º F and +1200º F.

A20

Alloy 20

A351

Corrosive service at temperatures between -20º F and +300º F.

* Limitations are per 2004 Edition of ASME B16.34.

Trim Materials The following are Cameron’s NEWCO standard trim designations. Wedge or Disc Facing (1)

Stem

Other Trim Parts (2)

CR 13

Non-corrosive applications. Steam, gas and general service to 700º F. Oil and oil vapor to 900º F.

CR 13

Steam, gas and general service to 1000º F. Standard trim for gate valves.

Full Stellite

CR 13

Premium trim service to 1200º F. Excellent for high pressure water and steam service.

316

Corrosive services to 850º F. Low temperature service standard for 316 SS valves.

Trim Number

Common Name

13 Chrome

Half Stellite

TC9308-3

API 600 Seat Ring Trim No. Facing (1)

Service Limitations

Wedge or Disc Facing (1)

Stem

Other Trim Parts (2)

316

Monel

NiCu

5/2

Monel/Half Stellite

NiCu

5/3

Monel/Full Stellite

NiCu

Alloy 20

A20

Corrosive services to 300º F.

Bronze

BRZ

Water, gas or low pressure steam to 450º F.

Aluminum Bronze

AL BRZ

Iron

STL

Iron or STL

Special

Trim Number

Common Name

API 600 Seat Ring Trim No. Facing (1)

4/2

316/Half Stellite

4/3

316/Full Stellite

Service Limitations

Corrosive services to 750º F.

Customer to specify.

(1) Facing is defined as the seating surface of a seat ring and wedge/disc. (2) Other trim parts are defined as small internal parts that are normally in contact with the service fluid. This includes the stem, backseat bushing in gate and globe valves and the swing check disc nut.

Sour Gas Service Materials Cameron’s NEWCO cast steel valves may be furnished with body and trim materials in compliance with NACE MR-01-75 specifications. The standard valve is WCB with double tempered trim 2 and Class II bolting. Other materials, trim and bolting are available. Features and Benefits • Certifications • International Organization for Standardization (ISO) • Traceability • Fugitive Emmisions Tested • API-598 Tested • Major End-user Approved • Multiple North American Locations • Extensive Engineering Capabilities • Excellent Customer Service • Warranty • Onsite Non-destructive Testing • Field Services for Start-up • Inhouse Automation Capabilities TC9308-3

Pressure Temperature Ratings - ASME B16.34 - 2004 Class 150 Temperature 째F (째C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

285 260 230 200 170 140 125 110 95 80 65 50 35 20 -

290 260 230 200 170 140 125 -

290 260 230 200 170 140 125 110 95 80 65 50 35 20 20** 20** -

290 260 230 200 170 140 125 110 95 80 65 50 35 20 20** 20** 20** 20**

290 260 230 200 170 140 125 110 95 80 65 50 35 20 20 20 20 20

Class 300

TC9308-3

Temperature 째F (째C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

740 680 655 635 605 570 550 530 505 410 320 230 135 85 -

750 750 730 705 665 605 590 -

750 750 720 695 665 605 590 570 530 510 485 450 320 215 145 95 65 40

750 750 730 705 665 605 590 570 530 500 485 450 385 265 175 110 70 40

750 750 730 705 665 605 590 570 530 510 485 375 275 200 145 100 60 35

750 750 730 705 665 605 590 570 530 510 485 450 375 255 170 115 75 50

750 750 730 705 665 605 590 570 530 510 485 450 385 365 360 300 225 145

Class 600 Temperature 째F (째C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

1480 1360 1310 1265 1205 1135 1100 1060 1015 825 640 460 275 170 -

1500 1500 1455 1405 1330 1210 1175 -

1500 1500 1445 1385 1330 1210 1175 1135 1065 1015 975 900 640 430 290 190 130 80

1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 535 350 220 135 80

1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 745 550 400 290 200 125 70

1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 505 345 225 150 105

1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 775 725 720 605 445 290

Class 900

TC9308-3

Temperature 째F (째C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

2220 2035 1965 1900 1810 1705 1650 1590 1520 1235 955 690 410 255 -

2250 2250 2185 2110 1995 1815 1765 -

2250 2250 2165 2080 1995 1815 1765 1705 1595 1525 1460 1350 955 650 430 290 195 125

2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1160 805 525 330 205 125

2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1120 825 595 430 300 185 105

2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1130 760 515 340 225 155

2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1160 1090 1080 905 670 430

Class 1500 Temperature °F (°C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

3705 3395 3270 3170 3015 2840 2745 2665 2535 2055 1595 1150 685 430 -

3750 3750 3640 3520 3325 3025 2940 -

3750 3750 3610 3465 3325 3025 2940 2840 2660 2540 2435 2245 1595 1080 720 480 325 205

3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1930 1335 875 550 345 205

3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 1870 1370 995 720 495 310 170

3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1885 1270 855 565 375 255

3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1930 1820 1800 1510 1115 720

Class 2500 Temperature °F (°C)

WCB*

LCC

WC6

WC9

C12

C12A

-20 to 100 (-29 to 38) 200 (93) 300 (148) 400 (204) 500 (260) 600 (316) 650 (343) 700 (371) 750 (399) 800 (427) 850 (454) 900 (482) 950 (510) 1000 (538) 1050 (566) 1100 (593) 1150 (621) 1200 (649)

6170 5655 5450 5280 5025 4730 4575 4425 4230 3430 2655 1915 1145 715 -

6250 6250 6070 5865 5540 5040 4905 -

6250 6250 6015 5775 5540 5040 4905 4730 4430 4230 4060 3745 2655 1800 1200 800 545 345

6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3220 2230 1455 915 570 345

6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3115 2285 1655 1200 830 515 285

6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3145 2115 1430 945 630 430

6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3220 3030 3000 2515 1855 1200

* Not recommended for prolonged use above 800° F. ** For weld end valves only. Flanged end ratings terminate at 1000° F.

Note: Packing, gasket, or bolting may limit temperature. Please advise service temperature if above 1000° F. Ratings from ASME B16.34 standard class valves. Special class weld end valves to ASME B16.34 are available on special order. TC9308-3

Flange Dimensions - ASME B16.5 Class 150 and 300

1/16”

1/4”

A D E B

Class 600 through 2500

A D E B

Standards: NPS 24 and smaller in all classes conform to ASME B16.5. NPS 30 and larger conform to ASME B16.47 (Series A). Facing: End flanges are regularly furnished with a raised face having a serrated finish per MSS SP-6. The thickness of the flange dimension (C) includes the raised face for Class 150 and 300. For Class 600 through 2500, the flange dimension (C) does not include the 1/4” raised face. Bolt Holes: Bolt holes are 1/8” larger than the bolt diameter. Bolt holes are drilled to straddle the center line.

TC9308-3

Flange Dimensions in Inches Class 150 Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) 30 (750) 36 (900) 42 (1050) 48 (1200)

2.00 2.50 3.00 4.00 5.00 6.00 8.00 10.00 12.00 13.25 15.25 17.25 19.25 23.25 29.25 35.06 40.87 46.00

6.00 7.00 7.50 9.00 10.00 11.00 13.50 16.00 19.00 21.00 23.50 25.00 27.50 32.00 38.75 46.00 53.00 59.50

0.75 0.88 0.94 0.94 0.94 1.00 1.12 1.19 1.25 1.38 1.44 1.56 1.69 1.88 2.94 3.56 3.81 4.25

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00 16.25 18.50 21.00 23.00 27.25 33.75 40.25 47.00 53.50

4.75 5.50 6.00 7.50 8.50 9.50 11.75 14.25 17.00 18.75 21.25 22.75 25.00 29.50 36.00 42.75 49.50 56.00

Stud Bolts No.

Diam.

Hole Diam.

4 4 4 8 8 8 8 12 12 12 16 16 20 20 28 32 36 44

0.63 0.63 0.63 0.63 0.75 0.75 0.75 0.88 0.88 1.00 1.00 1.125 1.125 1.25 1.25 1.50 1.50 1.50

0.75 0.75 0.75 0.75 0.88 0.88 0.88 1.00 1.00 1.13 1.13 1.25 1.25 1.38 1.38 1.63 1.63 1.63

Flange Dimensions in Inches Class 300

TC9308-3

Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) 30 (750) 36 (900)

2.00 2.50 3.00 4.00 5.00 6.00 8.00 10.00 12.00 13.25 15.25 17.00 19.00 23.00 29.00 34.50

6.50 7.50 8.25 10.00 11.00 12.50 15.00 17.50 20.50 23.00 25.50 28.00 30.50 36.00 43.00 50.00

0.88 1.00 1.12 1.25 1.38 1.44 1.62 1.88 2.00 2.12 2.25 2.38 2.50 2.75 3.62 4.12

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00 16.25 18.50 21.00 23.00 27.25 33.75 40.25

5.00 5.88 6.62 7.88 9.25 10.62 13.00 15.25 17.75 20.25 22.50 24.75 27.00 32.00 39.25 46.00

Stud Bolts No.

Diam.

Hole Diam.

8 8 8 8 8 12 12 16 16 20 20 24 24 24 28 32

0.63 0.75 0.75 0.75 0.75 0.75 0.88 1.00 1.13 1.13 1.25 1.25 1.25 1.50 1.75 2.00

0.75 0.88 0.88 0.88 0.88 0.88 1.00 1.13 1.25 1.25 1.38 1.38 1.38 1.63 1.88 2.13

Flange Dimensions in Inches Class 600 Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600) 30 (750) 36 (900)

2.00 2.50 3.00 4.00 5.00 6.00 8.00 10.00 12.00 13.25 15.25 17.00 19.00 23.00 29.00 34.50

6.50 7.50 8.25 10.00 11.00 12.50 15.00 17.50 20.50 23.00 25.50 28.00 30.50 36.00 43.00 50.00

0.88 1.00 1.12 1.25 1.38 1.44 1.62 1.88 2.00 2.12 2.25 2.38 2.50 2.75 3.62 4.12

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00 16.25 18.50 21.00 23.00 27.25 33.75 40.25

5.00 5.88 6.62 7.88 9.25 10.62 13.00 15.25 17.75 20.25 22.50 24.75 27.00 32.00 39.25 46.00

Stud Bolts No.

Diam.

Hole Diam.

8 8 8 8 8 12 12 16 16 20 20 24 24 24 28 32

0.63 0.75 0.75 0.75 0.75 0.75 0.88 1.00 1.13 1.13 1.25 1.25 1.25 1.50 1.75 2.00

0.75 0.88 0.88 0.88 0.88 0.88 1.00 1.13 1.25 1.25 1.38 1.38 1.38 1.63 1.88 2.13

Flange Dimensions in Inches Class 900

TC9308-3

Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600)

1.88 2.25 2.88 3.88 4.75 5.75 7.50 9.38 11.12 12.25 14.00 15.75 17.50 21.00

8.50 9.62 9.50 11.50 13.75 15.00 18.50 21.50 24.00 25.25 27.75 31.00 33.75 41.00

1.50 1.62 1.50 1.75 2.00 2.19 2.50 2.75 3.12 3.38 3.50 4.00 4.25 5.50

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00 16.25 18.50 21.00 23.00 27.25

6.50 7.50 7.500 9.25 11.00 12.50 15.50 18.50 21.00 22.00 24.25 27.00 29.50 35.50

Stud Bolts No.

Diam.

Hole Diam.

8 8 8 8 8 12 12 16 20 20 20 20 20 20

0.88 1.00 0.88 1.13 1.25 1.13 1.38 1.38 1.38 1.50 1.63 1.88 2.00 2.50

1.00 1.13 1.00 1.25 1.38 1.25 1.50 1.50 1.50 1.63 1.75 2.00 2.13 2.63

Flange Dimensions in Inches Class 1500 Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300) 14 (350) 16 (400) 18 (450) 20 (500) 24 (600)

1.88 2.25 2.75 3.62 4.38 5.38 7.00 8.75 10.38 11.38 13.00 14.62 16.38 19.62

8.50 9.62 10.50 12.25 14.75 15.50 19.00 23.00 26.50 29.50 32.50 36.00 38.75 46.00

1.50 1.62 1.88 2.12 2.88 3.25 3.62 4.25 4.88 5.25 5.75 6.38 7.00 8.00

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00 16.25 18.50 21.00 23.00 27.25

6.50 7.50 8.00 9.50 11.50 12.50 15.50 19.00 22.50 25.00 27.75 30.50 32.75 39.00

Stud Bolts No.

Diam.

Hole Diam.

8 8 8 8 8 12 12 12 16 16 16 16 16 16

0.88 1.00 1.13 1.25 1.50 1.38 1.63 1.88 2.00 2.25 2.50 2.75 3.00 3.50

1.00 1.13 1.25 1.38 1.63 1.50 1.75 2.00 2.13 2.38 2.63 2.88 3.13 3.63

Flange Dimensions in Inches Class 2500 Size In. (mm)

2 (50) 2.5 (65) 3 (80) 4 (100) 5 (125) 6 (150) 8 (200) 10 (250) 12 (300)

1.50 1.88 2.25 2.88 3.62 4.38 5.75 7.25 8.62

9.25 10.50 12.00 14.00 16.50 19.00 21.75 26.50 30.00

2.00 2.25 2.62 3.00 3.62 4.25 5.00 6.50 7.25

3.62 4.12 5.00 6.19 7.31 8.50 10.62 12.75 15.00

6.75 7.75 9.00 10.75 12.75 14.50 17.25 21.75 24.38

Stud Bolts No.

Diam.

Hole Diam.

8 8 8 8 8 8 12 12 12

1.00 1.13 1.25 1.50 1.75 2.00 2.00 2.50 2.75

1.13 1.25 1.38 1.63 1.88 2.13 2.13 2.63 2.88

Auxiliary Connection Locations (Bypasses, Drains, etc.) Bypasses Bypasses serve two purposes. They are used in steam services as a means to warm the line before the main valve is opened. They are also used to balance the pressure on both sides of the main valve as an aid to reduce the torque required to open the main valve. Cameronâ&#x20AC;&#x2122;s NEWCO cast steel valve can be furnished with all welded bypasses when specified. The standard bypass configuration is the single valve bypass attached to the side of the main valve with the stems of both valves parallel as shown below. Piping and the OS&Y globe bypass valve have a pressure-temperature rating and corrosion resistance equal to exceeding that of the main valve. TC9308-3

When other bypass configurations are required, a sketch or drawing must accompany the order. Drains Cameron’s NEWCO cast steel valves can be furnished with drains at any of the locations shown. Standard drain connections consist of a drilled, tapped, and plugged hole at the location(s) specified. Other types of drains, including welding or threaded nipples with or without shut-off valves, can also be furnished when specified. Please refer to ASME B16.34 for exact auxiliary connection locations, sizes and threading information. Each letter in the illustration(s) below identifies the possible hole locations for auxiliary connection(s). These illustrations are for reference purposes only. Unless specified otherwise, auxiliary connection hole sizes shall be drilled and tapped as follows: • 2” through 4” utilizes a .50” hole • 5” through 8” utilizes a .75” hole • 10” and larger utilizes a 1” hole Gate Valves

Check Valves

Globe Valves

Angle Valves

TC9308-3

I. CAST STEEL BOLTED BONNET GATE VALVES SIZES: 2” TO 48” (50MM TO 1200MM) • PRESSURE CLASS: 150 TO 1500 Typical Cast Steel Bolted Bonnet Gate Valve Expanded View

15 8 7 12

23 10

3 2

9 13 11 21 4 6

19 20

TC9308-3

1. Body: Cameron’s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Yoke and Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the bodies. Larger size gate valves utilize a multi-piece bonnet design. 3. Grease Fitting: The grease fitting allows for easy stem lubrication. 4. Stem: The stem is precision machined and inserts into the horizontal channel in the disc. 5. Wedge: Cameron’s 1-piece flex wedge is machined to the tightest tolerances to ensure trouble free shut-off and cycling. 6. Back Seat Bushing: The back seat, when engaged with the stem head, provides a stable shut-off to the stuffing box which isolates the packing from flow exposure. 7. Gland: The gland compresses the packing to create a stem seal above the back seat, between the bonnet and stem. 8. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments. 9. & 10. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 11. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet. 12. Packing: The packing creates a seal above the back seat, between the bonnet and stem. 13. Stuffing Box: The stuffing box contains the packing. 14. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 15. Yoke Bushing: The retaining nut secures the stem nut to the bonnet assembly. 16. Handwheel: The handwheel cycles the valve. 17. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 18. Set Screw: The set screw prevents handwheel nut loosening. 19. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 20. & 21. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the body. 22. Seat Rings: To ensure a stable shut-off, seat rings are aligned and seal-welded into the valve, then precision ground for optimal seating. 23. Spacer Ring: Assists the packing rings in creating a seal above the back seat, between the bonnet and stem.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class 150 - Sizes: 2â&#x20AC;? to 48â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts* C

B (open) Optional split-yoke and vertical handwheel.

A-RF & RTJ

A-BW

** Gear operated is standard. Handwheel available upon request.

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Seat Rings Wedge 2” - 3” Wedge 4” and larger Stem Yoke and Bonnet *Bonnet Gasket Bonnet Nuts Bonnet Studs Back Seat Bushing *Packing Gland Gland Flange Gland Bolt Pins Gland Bolts Gland Nuts Nameplate Nameplate Rivets Grease Fitting Stem Nut Yoke Bushing Handwheel Handwheel Nut Set Screw Spacer Ring

CB3

CB4/2

ASTM A216-WCB ASTM A105/HF ASTM A276-410 ASTM A351- CF8M/A276-316 ASTM A216-WCB/HF ASTM A216-WCB w/13% Chrome ASTM A216-WCB w/316 Hardface ASTM A182-F6a ASTM A182-316 ASTM A216-WCB Multilayered Corrugated 316 w/Graphite ASTM A194-2H ASTM A194-2HM ASTM A193-B7 ASTM A193-B7M ASTM A276-410 ASTM A276-316 Graphite w/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-316 ASTM A216-WCB ASTM A36 ASTM A307-B ASTM A194-2H Stainless Steel 304 Stainless Steel - Commercial Carbon Steel - Commercial ASTM A439-D2 ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A193-B6 N/A Class 150

Size

NPS

2.5

In mm In A-BW mm In B mm In C mm RF Lbs Wt. Kg BW Lbs Wt. Kg A-RF

100 125 150 200 250 300 350 400 450 500 600 750 900 1050 1200

7.0 7.5 8.0 9.0 10.0 178 191 203 229 254 8.5 9.5 11.1 12.0 15.0 216 241 282 305 381 14.8 17.1 18.2 22.6 28.1 376 434 462 574 714 8.0 8.0 8.0 10.0 13.8 203 203 203 254 350 46 56 71 111 163 21 25 32 50 74 40 46 58 91 152 18 21 26 41 69

10.5 267 15.9 404 33.2 843 14.0 356 196 89 180 82

11.5 292 16.5 419 38.9 988 16.0 406 289 131 259 118

13.0 330 18.0 457 46.4 1179 18.0 457 449 204 425 193

14.0 356 19.8 503 54.6 1387 20.0 508 639 290 584 265

15.0 381 22.5 572 63.5 1613 22.0 559 860 391 811 369

16.0 406 24.0 610 72.4 1839 24.0 610 1190 541 1146 521

17.0 432 26.0 660 79.2 2012 27.0 686 1389 631 1349 613

18.0 457 28.0 711 86.0 2184 30.0 762 1786 812 1720 782

20.0 508 32.0 813 100.8 2560 30.0 762 2602 1183 2534 1152

24.0 610 24.0 610 125.1 3178 35.0 889 4466 2030 4037 1835

28.0 711 28.0 711 153.2 3891 43.0 1092 4850 1193 4385 1993

31.0 813 43.0 1092 174.4 4430 35.4 **900 10134 4600 10198 4625

34.0 864 46.0 1168 217.5 5525 35.4 **900 15677 8500 15545 8550

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class 300 - Sizes: 2â&#x20AC;? to 36â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

Optional split-yoke and vertical handwheel.

A-RF

A-BW

** Gear operated is standard. Handwheel available upon request.

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

ASTM A276-410 ASTM A216-WCB w/13% Chrome ASTM A182-F6a

CB4/2

ASTM A216-WCB ASTM A105/HF ASTM A216-WCB/HF ASTM A216-WCB/HF

ASTM A351-CF8M/A276-316 ASTM A216-WCB w/316 Hardface ASTM A182-316

ASTM A216-WCB Spiral Wound 316 Stainless Steel/Graphite ASTM A194-2H ASTM A193-B7 ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A216-WCB ASTM A36 ASTM A307-B ASTM A194-2H Stainless Steel 304 Stainless Steel - Commercial Carbon Steel - Commercial ASTM A439-D2 ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A193-B6 ASTM A276-410

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

Class 300 Size

NPS

2.5

100

125

150

200

250

300

350

400

450

500

600

750

900

In mm In mm In mm In mm Lbs Kg Lbs Kg

8.5 216 8.5 216 17.2 437 8.0 203 64 29 51 23

9.5 241 9.5 241 19.1 485 10.0 254 88 40 68 31

11.1 282 11.1 282 20.0 508 10.0 254 112 51 86 39

12.0 305 12.0 305 24.0 610 12.0 305 175 80 154 70

15.0 381 15.0 381 29.6 752 13.7 350 258 117 207 94

15.9 404 15.9 404 33.0 838 16.0 406 340 155 269 122

16.5 419 16.5 419 41.1 1044 18.0 457 542 246 430 195

18.0 457 18.0 457 49.3 1252 20.0 508 816 371 620 282

19.75 502 19.75 502 57.0 1448 22.0 559 1072 487 871 396

30.0 762 30.0 762 67.0 1702 25.2 640 1764 802 1323 601

33.0 838 33.0 838 73.1 1857 27.0 686 2183 992 1830 832

36.0 914 36.0 914 82.2 2088 27.0 686 2867 1303 2381 1082

39.0 991 39.0 991 95.5 2426 30.0 762 3682 1674 3109 1413

45.0 55.0 68.0 1143 1397 1727 45.0 55.0 68.0 1143 1397 1727 104.7 136.3 169.8 2659 3462 4312 30.0 31.9 31.9 762 **810 **810 5645 9702 15104 2566 4410 6850 4873 8350 11003 2215 3795 4990

A-RF A-BW B C RF Wt. BW Wt.

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 600 - Sizes: 2â&#x20AC;? to 24â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

Optional split-yoke and vertical handwheel.

A-BW

A-RF & RTJ

** Gear operated is standard. Handwheel available upon request.

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

ASTM A276-410 ASTM A216-WCB w/13% Chrome ASTM A182-F6a

CB4/2

ASTM A216-WCB ASTM A105/HF ASTM A216-WCB/HF ASTM A216-WCB/HF

ASTM A351-CF8M/A276-316 ASTM A216-WCB w/316 Hardface ASTM A182-316

ASTM A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM A193-B7 ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A216-WCB ASTM A36 ASTM A307-B ASTM A194-2H Stainless Steel 304 Stainless Steel - Commercial Carbon Steel - Commercial ASTM A439-D2 ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A193-B6 ASTM A276-410

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

Class 600 Size A-RF A-BW A-RTJ B C RF-RTJ Wt. BW Wt.

NPS

2.5

100

125

150

200

250

300

350

400

450

500

600

In mm In mm In mm In mm In mm Lbs Kg Lbs Kg

11.5 292 11.5 292 11.62 295 18.3 465 10.0 254 97 44 79 36

13.0 330 13.0 330 13.12 333 19.9 505 10.0 254 132 60 120 55

14.0 356 14.0 356 14.12 359 21.7 551 12.0 305 176 80 152 69

17.0 432 17.0 432 17.12 435 26.9 683 15.0 381 320 145 270 123

20.0 508 20.0 508

22.0 559 22.0 559 22.12 562 36.5 927 20.0 508 680 309 580 264

26.0 660 26.0 660 26.12 664 44.0 1118 24.0 610 1150 523 1020 464

31.0 787 31.0 787 31.12 791 52.8 1341 27.0 686 1715 780 1430 650

33.0 838 33.0 838 33.12 841 61.4 1560 27.0 686 2440 1109 1950 886

35.0 889 35.0 889 35.12 892 64.8 1646 30.0 762 3150 1432 2695 1225

39.0 991 39.0 991 39.12 994 71.7 1821 35.0 889 4415 2007 3800 1727

43.0 1092 43.0 1092 43.12 1095 79.3 2014 43.0 1092 5010 2277 5010 2277

47.0 1194 47.0 1194 47.25 1200 104.8 2662 43.0 1092 6853 3108 5640 2558

55.0 1397 55.0 1397 55.38 1406 116.9 2970 31.9 **810 10337 4688 8595 3898

31.6 803 18.0 457 520 236 430 195

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 900 - Sizes: 2â&#x20AC;? to 12â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

Optional split-yoke and vertical handwheel.

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

ASTM A276-410 ASTM A216-WCB w/13% Chrome ASTM A182-F6a

CB4/2

ASTM A216-WCB ASTM A105/HF ASTM A216-WCB/HF ASTM A216-WCB/HF

ASTM A351-CF8M/A276-316 ASTM A216-WCB w/316 Hardface ASTM A182-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

Class 900 Size A-RF A-BW A-RTJ B C RF-RTJ Wt. BW Wt.

NPS

2.5

100

150

200

250

300

In mm In mm In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 14.62 371 21.7 551 9.8 250 135 61 125 57

16.5 419 16.5 419 16.62 422 26.0 660 9.8 250 175 385 155 70

15.0 381 15.0 381 15.12 384 23.7 602 13.8 350 255 116 213 97

18.0 457 18.0 457 18.12 460 27.6 701 13.8 350 453 206 396 180

24.0 610 24.0 610 24.12 612 38.4 975 22.0 560 913 415 807 367

29.0 737 29.0 737 29.12 740 45.5 1156 25.2 640 1705 775 1465 665

33.0 838 33.0 838 33.12 841 52.6 1336 30.0 760 2387 1085 1724 784

38.0 965 38.0 965 38.12 968 59.8 1519 30.0 760 3600 1636 2790 1268

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 1500 - Sizes: 2â&#x20AC;? to 12â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

Optional split-yoke and vertical handwheel.

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A351-CF8M/A276-316 ASTM A216-WCB w/13% Chrome ASTM A216-WCB/ HF ASTM A216-WCB w/316 Hardface ASTM A182-F6a ASTM A182-316 ASTM A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM A194-2HM ASTM A193-B7 ASTM A193-B7M ASTM A276-410 ASTM A276-316 Graphite w/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-316 ASTM A216-WCB ASTM A36 ASTM A307-B ASTM A194-2H Stainless Steel 304 Stainless Steel - Commercial Carbon Steel - Commercial ASTM A439-D2 ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A536 (65-45-12) ASTM A193-B6 ASTM A276-410 Class 1500

Size A-RF A-BW A-RTJ B C RF-RTJ Wt. BW Wt.

NPS

2.5

100

150

200

250

300

In mm In mm In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 14.62 371 21.7 551 11.8 300 128 58 106 48

16.5 419 16.5 419 16.62 422 26.0 660 11.8 300 163 74 137 62

18.5 470 18.5 470 18.62 473 28.5 724 15.75 400 209 95 174 79

21.5 546 21.5 546 21.62 549 32.6 828 19.6 500 423 192 352 160

27.8 706 27.8 706 28.0 711 39.3 998 23.6 600 978 445 870 395

32.75 832 32.75 832 33.13 841 48.1 1223 30.0 760 1625 739 1650 750

39.0 991 39.0 991 39.38 1000 66.5 1688 30.0 760 4412 2001 3541 1606

44.5 1130 44.5 1130 45.12 1146 82.3 2090 35.0 889 8414 3816 7080 3211

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. TC9308-3

II. CAST STEEL BOLTED BONNET GLOBE VALVES SIZES: 2” TO 14” (50MM TO 350MM) • PRESSURE CLASS: 150 TO 1500 Typical Cast Steel Bolted Bonnet Globe Valve Expanded View 18 19

9 14

25 2

15 13 22

3 20

22 1 4

23 5 8

TC9308-3

1. Body: Cameron’s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the bodies. 3. Back Seat Bushing: The back seat, when engaged with the stem head, provides a stable shut-off to the stuffing box which isolates the packing from flow exposure. 4. Stem: The stem inserts vertically into the disc. 5. Lock Groove: The lock groove receives the split lock ring, which allows the disc nut to lift the disc during cycling. 6. Split Ring: The split ring allows the disc nut to lift the disc during cycling. 7. Disc: Cameron’s plug type disc is machined to the tightest tolerances to ensure trouble free shut-off and cycling. 8. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the stem. 9. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 10. Gland Flange: The gland flange applies pressure to the gland for accurate packing compression. 11. & 12. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 13. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet. 14. Packing: The packing creates a seal above the back seat between the bonnet and stem. 15. Stuffing Box: The stuffing box contains the packing. 16. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 17. Handwheel: The handwheel cycles the valve. 18. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 19. Handwheel Washer: The washer helps to prevent loosening or distributes pressure evenly. 20. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 21. & 22. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the body. 23. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the valve, then precision ground for optimal seating. 24. Disc Guide: The disc guides provide a stable track for keeping the disc aligned with the seat during cycling. 25. Spacer Ring: The spacer ring assists the packing rings in creating a seal above the back seat between the bonnet and stem.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 150 - Sizes: 2â&#x20AC;? to 14â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Optional gear operator and vertical handwheel.

B (open)

A-BW

A-RF

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Disc 2” through 4” Disc 5” and larger Stem Bonnet *Bonnet Gasket Bonnet Nuts Bonnet Studs Back Seat Bushing *Packing Gland Gland Flange Gland Bolt Pins Gland Nuts Gland Bolts Seat Ring Split Ring Nameplate Nameplate Rivets Disc Nut Stem Nut Handwheel Washer Handwheel Nut Handwheel Spacer Ring

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A216-WCB Spiral Wound 316 Stainless Steel/Graphite ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B ASTM A105/HF ** ASTM A276-410 ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) N/A

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 150 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

125

150

200

250

300

350

In mm In mm In mm In mm Lbs Kg Lbs Kg

8.0 203 8.0 203 14.9 378 8.0 203 51 23 51 23

8.5 216 8.5 216 15.8 401 10.0 254 73 33 73 33

9.5 241 9.5 241 16.6 422 10.0 254 93 42 93 42

11.5 292 11.5 292 19.9 505 12.0 305 137 62 137 62

14.0 356 14.0 356 21.8 554 14.0 356 192 87 192 87

16.0 406 16.0 406 22.4 569 16.0 406 243 110 243 110

19.5 495 19.5 495 26.5 673 18.0 457 419 190 419 190

24.5 622 24.5 622 30.6 777 22.0 559 507 276 507 276

27.5 699 27.5 699 34.8 884 24.0 610 948 476 948 476

31.0 787 31.0 787 41.4 1052 25.2 640 1276 625 1276 625

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 300 - Sizes: 2â&#x20AC;? to 14â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 and API RP591 Recommended Spare Parts**

Optional gear operator and vertical handwheel.

B (open)

A-BW

A-RF

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/ 13% Chrome ASTM A276-410 ASTM A216-WCB Spiral Wound 316 Stainless Steel/Graphite ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B ASTM A105/HF** ASTM A276-410 ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 300 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

125

150

200

250

300

350

In mm In mm In mm In mm Lbs Kg Lbs Kg

10.5 267 10.5 267 16.9 429 10.0 254 75.0 34 55 25

11.5 292 11.5 292 17.8 452 10.0 254 100.0 45 79 36

12.5 318 12.5 318 19.2 488 12.0 305 130.0 59 101 46

14.0 357 14.0 357 23.0 584 14.0 356 203.0 92 163 74

15.75 400 15.75 400 27.4 696 14.0 406 294.0 134 242 110

17.5 445 17.5 445 30.6 777 18.0 457 421.0 191 355 161

22.0 559 22.0 559 36.2 919 24.0 610 715 325 566 257

24.5 622 24.5 622 40.8 1036 24.0 610 1015 461 770 350

28.0 711 28.0 711 47.3 1201 27.0 686 1500 682 1218 554

33.0 838 33.0 838 54.3 1379 28.3 720 2446 1112 1996 907

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 600 - Sizes: 2” to 8” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 and API RP591 Recommended Spare Parts**

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component Body Disc 2” through 4” Disc 5” and larger Stem Bonnet *Bonnet Gasket Bonnet Nuts Bonnet Studs Back Seat Bushing *Packing Gland Gland Flange Gland Bolt Pins Gland Nuts Gland Bolts Seat Ring Split Ring Nameplate Nameplate Rivets Disc Nut Stem Nut Handwheel Washer Handwheel Nut Handwheel Spacer Ring

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/ 13% Chrome ASTM A276-410 ASTM A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B Integral ASTM A216-WCB/HF ASTM A276-410 ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 600 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

150

200

In mm In mm In mm In mm Lbs Kg Lbs Kg

11.5 292 11.5 292 18.4 467 10.0 254 90 41 79 36

13.0 325 13.0 325 20.0 508 10.0 254 130 59 110 50

14.0 256 14.0 256 24.4 620 14.0 356 170 77 141 64

17.0 435 17.0 435 29.0 737 18.0 457 313 142 256 116

22.0 559 22.0 559 37.9 963 24.0 610 778 354 640 291

26.0 660 26.0 660 44.7 1135 24.0 610 1245 566 961 437

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 900 - Sizes: 2â&#x20AC;? to 8â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 900 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

100

150

200

In mm In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 22.6 574 13.8 350 198 90 176 80

15.0 381 15.0 381 26.0 660 17.7 450 335 152 297 135

18.0 457 18.0 457 30.6 777 17.7 450 440 200 376 171

24.0 610 24.0 610 39.6 1006 22.0 560 1675 761 1144 520

29.0 737 29.0 737 60.1 1527 28.3 720 2090 950 1634 743

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 1500 - Sizes: 2â&#x20AC;? to 6â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A276-316 ASTM A216- WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 1500 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

100

150

In mm In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 19.6 498 13.8 350 209 95 143 65

18.5 470 18.5 470 25.6 650 17.7 450 551 250 460 209

21.5 546 21.5 546 30.8 782 19.7 500 959 436 830 377

27.75 705 27.75 705 36.5 927 25.2 640 1191 541 996 453

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

III. CAST STEEL BOLTED BONNET ANGLE VALVES SIZES: 2” TO 12” (50MM TO 300MM) • PRESSURE CLASS: 150 TO 600 Typical Cast Steel Bolted Bonnet Angle Valve Expanded View 18 19

9 14

25 2

15 13 22

3 20

22 1 4

23 5 8

TC9308-3

1. Body: Cameronâ&#x20AC;&#x2122;s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Bonnet: Cameronâ&#x20AC;&#x2122;s NEWCO bonnet assemblies are built to the same standards as the bodies. 3. Back Seat Bushing: The back seat, when engaged with the stem head, provides a stable shut-off to the stuffing box which isolates the packing from flow exposure. 4. Stem: The stem inserts vertically into the disc. 5. Lock Groove: The lock groove receives the split lock ring which allows the disc nut to lift the disc during cycling. 6. Split Ring: The split ring allows the disc nut to lift the disc during cycling. 7. Disc: The disc is machined to the tightest tolerances to ensure trouble free shut-off and cycling. 8. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the stem. 9. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 10. Gland Flange: The gland flange applies pressure to the gland for accurate packing compression. 11. & 12. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 13. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet. 14. Packing: The packing creates a seal above the back seat between the bonnet and stem. 15. Stuffing Box: The stuffing box contains the packing. 16. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 17. Handwheel: The handwheel cycles the valve. 18. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 19. Handwheel Washer: The washer helps to prevent loosening or distributes pressure evenly. 20. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 21. & 22. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the body. 23. Seat Ring: To ensure a stable shut-off, the seat rings are aligned and seal-welded into the valve, then precision ground for optimal seating. 24. Disc Guide: The disc guides provide a stable track for keeping the disc aligned with the seat during cycling. 25. Spacer Ring: The spacer ring assists the packing rings in creating a seal above the back seat between the bonnet and stem.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 150 - Sizes: 2â&#x20AC;? to 12â&#x20AC;? Pressure Class Range: 150 to 600 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component Body Seat Ring Disc 2” through 4” Disc 5” and larger Disc Nut Stem *Bonnet Gasket Bonnet Bonnet Studs Bonnet Nuts Back Seat Bushing Packing Gland Bolt Pins Gland Bolts Gland Gland Flange Gland Nuts Stem Nut Split Ring Handwheel Washer Handwheel Nut Handwheel Spacer Ring

CB2

CB3

CB4/2

ASTM A216 GR.WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/ 13% Chrome ASTM A276-410 ASTM A276-410 Spiral Wound 316 Stainless Steel/Graphite ASTM A216-WCB ASTM 193-B7 ASTM A194-2H ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A36 ASTM 193-B7 ASTM A276-410 ASTM A216-WCB ASTM A194-2H ASTM A439-D2 ASTM A276-410 ASTM A36 ASTM A36 ASTM A539 Type (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 150 Size A B C D RF Wt.

NPS

DN In mm In mm In mm In mm Lbs Kg

100

150

200

250

300

4.0 107 15.2 386 8 203 6 152 57 26

4.75 121 16.9 429 10 254 7.5 191 84 38

5.75 146 20.4 518 12 305 9 229 141 64

8.0 203 21.8 554 15 381 11 279 234 106

9.75 248 27.4 696 18 457 13.5 343 399 181

12.25 311 31 787 22 559 16 406 611 278

13.75 349 37.8 960 24 610 19 483 794 361

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 300 - Sizes: 2â&#x20AC;? to 12â&#x20AC;? Pressure Class Range: 150 to 600 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

TC9308-3

CB2

CB3

CB4/2

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 300 Size A B C D RF Wt.

NPS

100

150

200

250

300

In mm In mm In mm In mm Lbs Kg

5.25 133 15 381 10 254 6.5 165 68 31

6.25 159 16.9 429 12 305 8.25 210 108 49

7 178 21.7 551 14 356 10 254 198 90

8.75 222 28 711 17 432 12.5 318 392 178

11 279 30.7 780 24 610 15 381 560 255

12.25 311 37.5 953 24 610 17.5 445 934 425

14 356 41.6 1049 27 686 20.5 521 1288 586

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 600 - Sizes: 2â&#x20AC;? to 8â&#x20AC;? Pressure Class Range: 150 to 600 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

B (open)

TC9308-3

CB2

CB3

CB4/2

ASTM A216 GR.WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A276-410 Spiral Wound 316 Stainless Steel/Graphite ASTM A216-WCB ASTM 193-B7 ASTM A194-2H ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A36 ASTM 193-B7 ASTM A276-410 ASTM A216-WCB ASTM A194-2H ASTM A439-D2 ASTM A276-410 ASTM A36 ASTM A36 ASTM A539 Type (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 600 Size A B C D RF Wt.

NPS

2.5

100

150

200

250

In mm In mm In mm In mm Lbs Kg

5.75 146 18.9 480 8.8 224 6.5 165 79 36

6.5 165 20.9 531 9.8 249 7.5 191 110 50

7.0 178 19.8 503 11.0 279 8.3 211 141 64

8.5 216 22.2 564 14.0 356 9.0 229 256 116

11.0 279 28.2 716 17.7 450 14.0 356 640 291

13.0 330 38.5 978 24.8 630 16.5 419 961 437

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

IV. CAST STEEL BOLTED COVER SWING CHECK VALVES SIZES: 2” TO 24” (50MM TO 600MM) • PRESSURE CLASS: 150 TO 1500 Typical Cast Steel Bolted Cover Swing Check Valve Expanded View

13 12

12 1 6 4

8 9

7 5

TC9308-3

Note: Classes 150 and 300 use external hinge pin. 1. Body: Cameronâ&#x20AC;&#x2122;s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Cover: The cover allows access to internal components. 3. Cover Gasket: The cover gasket creates a leakproof seal between the bonnet and body. 4. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the valve, then precision ground for optimal seating. 5. Disc: The disc allows unidirectional flow and restricts back flow with trouble free shutoff. 6. Swing Arm: The swing arm allows the disc to open and close. 7. & 8. Disc Nut and Pin: The disc nut and pin secure the disc to the swing arm. 9. Hinge Pin: The hinge pin provides a stable mechanism for the swing arm to operate. 10. Plug: The plug secures the arm pin inside the valve. 11. Plug Gasket: The plug gasket creates a leak-proof seal between the plug and body. 12. & 13. Cover Studs and Nuts: The cover studs and nuts secure the bonnet to the body. 14. Eyebolt: The eyebolt is use to aid in lifting the valve.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 150 - Sizes: 2” to 24” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Hinge pin and plug details

Eye bolts are on sizes 5” and larger B

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Cover Disc 2” through 5” Disc 6” and larger Swing Arm Seat Ring *Cover Gasket Hinge Pin Name Plate Plug Gasket Cover Bolt Cover Nut Plug Disc Pin Disc Nut Eye Bolt 5” through 24”

CB3

CB4/2

ASTM A216-WCB ASTM A105N ASTM A182-F6a ASTM A182-F6a/HF ASTM A182-F316 ASTM A216-WCB/13% Chrome ASTM A216-WCB/HF ASTM A216-WCB/316 Faced ASTM A216-WCB ASTM A105/HF Spiral Wound 316 Stainless Steel/Graphite ASTM A276-410 ASTM A276-316 304 Stainless Steel Stainless Steel ASTM A193-B7 ASTM A193-B7M AISI 1020 ASTM A276-410 ASTM A276-316 ASTM A276-316 A194-8 Carbon Steel Class 150

Size A-RF A-BW B RF Wt. BW Wt.

NPS

2.5

100

150

125

150

200

250

300

350

400

450

500

600

In mm In mm In mm Lbs Kg Lbs Kg

8.0 203 8.0 203 6.8 173 36 16 29 13

8.5 216 8.5 216 7.4 188 51 23 38 17

9.5 241 9.5 241 7.7 196 64 29 49 22

11.5 292 11.5 292 8.5 216 98 45 73 33

13.0 330 13.0 330 12.3 315 135 61 110 50

14.0 356 14.0 356 12.8 325 181 398 146 66

19.5 495 19.5 495 14.3 363 298 135 243 110

24.5 622 24.5 622 17.2 437 463 210 421 191

27.5 699 27.5 699 17.9 455 688 313 591 269

31.0 787 31.0 787 19.6 498 898 408 766 348

34.0 864 34.0 864 21.2 538 1147 521 979 445

38.5 978 38.5 978 24.2 615 1367 621 1190 541

38.5 978 38.5 978 27.4 696 1808 822 1585 720

51.0 1295 51.0 1295 30.0 762 2866 1308 2250 1123

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 300 - Sizes: 2” to 24” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Hinge pin and plug details

Eye bolts are on sizes 5” and larger B

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Cover Disc 2” through 5” Disc 6” and larger Swing Arm Seat Ring *Cover Gasket Hinge Pin Name Plate Plug Gasket Cover Bolt Cover Nut Plug Disc Pin Disc Nut Eye Bolt 5” through 24”

CB3

CB4/2

ASTM A216-WCB ASTM A105N ASTM A182-F6a ASTM A182-F6a/HF ASTM A182-F316 ASTM A216-WCB/13% Chrome ASTM A216-WCB/HF ASTM A216-WCB/316 Faced ASTM A216-WCB ASTM A105/HF Spiral Wound 316 Stainless Steel/Graphite ASTM A276-410 ASTM A276-316 304 Stainless Steel Stainless Steel ASTM A193-B7 ASTM A193-B7M ASTM A276-410 ASTM A276-316 AISI 1020 ASTM A276-316 A194-8 Carbon Steel Class 300

Size A-RF A-BW B RF Wt. BW Wt.

NPS

2.5

100

150

125

150

200

250

300

350

400

450

500

600

In mm In mm In mm Lbs Kg Lbs Kg

10.5 267 10.5 267 7.6 193 58 26 44 20

11.5 292 11.5 292 8.3 211 86 39 55 25

12.5 318 12.5 318 8.9 226 95 43 78 35

14.0 356 14.0 356 9.8 249 144 65 103 47

15.75 400 15.75 400 13.3 338 232 105 185 84

17.5 445 17.5 445 14.0 356 283 129 214 97

21.0 533 21.0 533 15.9 404 433 197 341 155

24.5 622 24.5 622 18.7 475 694 315 562 255

28.0 711 28.0 711 21.9 556 1003 456 815 370

33.0 838 33.0 838 23.1 587 1345 611 1087 494

34.0 864 34.0 864 25.2 640 1720 782 1397 635

38.5 978 38.5 978 28.6 726 2271 1032 1873 851

40.0 1016 40.0 1016 30.2 767 2888 1313 2400 1091

53.0 1346 53.0 1346 33.6 853 4718 2145 3995 1816

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 600 - Sizes: 2” to 14” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Eye bolts are on sizes 5” and larger B

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Cover Disc 2” through 5” Disc 6” and larger Swing Arm Seat Ring *Cover Gasket Hinge Pin Name Plate Washer Cover Bolt Cover Nut Plug Pin Hex Nut Eye Bolt 5” through 24”

CB3

CB4/2

ASTM A216-WCB ASTM A105N ASTM A182-F6a ASTM A182-F6a/HF ASTM A216-WCB/13% Chrome ASTM A216-WCB/HF ASTM A216-WCB ASTM A105/HF Soft Steel Ring Joint ASTM A276-410 304 Stainless Steel Stainless Steel ASTM A193-B7 ASTM A276-410 AISI 1020 ASTM A276-316 A194-8 Carbon Steel

ASTM A182-F316 ASTM A216-WCB/316 Faced

ASTM A276-316

ASTM A193-B7M ASTM A276-316

Class 600 Size A-RF A-BW B RF Wt. BW Wt.

NPS

2.5

100

150

125

150

200

250

300

350

In mm In mm In mm Lbs Kg Lbs Kg

11.5 292 11.5 292 7.8 198 65 30 51 23

13.0 330 13.0 330 8.8 224 90 41 68 31

14.0 356 14.0 356 9.7 246 115 52 91 41

17.0 432 17.0 432 13.3 338 215 98 161 73

20.0 508 20.0 508 15.5 394 348 159 255 116

22.0 559 22.0 559 16.8 427 481 219 349 159

26.0 660 26.0 660 19.4 493 926 421 762 346

31.0 787 31.0 787 22.6 574 1279 581 1021 483

33.0 838 33.0 838 25.4 645 1722 783 1411 641

35.0 889 35.0 889 26.4 671 2009 913 1650 750

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 900 - Sizes: 2” to 8” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Eye bolts are on sizes 5” and larger B

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

Body Cover Disc 2” through 5” Disc 6” and larger Swing Arm Seat Ring *Cover Gasket Hinge Pin Name Plate Washer Cover Bolt Cover Nut Plug Pin Hex Nut Eye Bolt 5” through 24”

CB3

CB4/2

ASTM A182-F316 ASTM A216-WCB/316 Faced

ASTM A276-316

ASTM A193-B7M ASTM A276-316

Class 900 Size A-RF A-BW B RF Wt. BW Wt.

NPS

100

150

200

In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 13.1 329 104 47 78 35

15.0 381 15.0 381 14.8 329 184 84 138 63

18.0 457 18.0 457 14.5 368 344 156 258 129

24.0 610 24.0 610 18.8 478 770 350 578 263

29.0 737 29.0 737 23.6 599 1482 674 1112 505

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 1500 - Sizes: 2” to 8” Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Eye bolts are on sizes 5” and larger B

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component Body Cover Disc 2” through 5” Disc 6” and larger Swing Arm Seat Ring *Cover Gasket Hinge Pin Name Plate Washer Cover Bolt Cover Nut Plug Pin Hex Nut Eye Bolt 5” through 24”

CB2

CB3

CB4/2

ASTM A182-F316 ASTM A216-WCB/316 Faced

ASTM A276-316

ASTM A193-B7M ASTM A276-316

Class 1500 Size A-RF A-BW B RF Wt. BW Wt.

NPS

2.5

100

150

200

203

In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 13.1 333 165 75 153 70

16.5 419 16.5 419 13.7 348 243 110 223 101

18.5 470 18.5 470 14.8 376 284 129 256 116

21.5 546 21.5 546 15.2 386 462 269 425 193

27.8 706 27.8 706 19.2 488 940 427 895 407

32.8 833 32.8 833 27.0 686 1030 468 985 448

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

V. CAST STEEL BOLTED COVER TILTING DISC CHECK VALVES SIZES: 2” TO 12” (50MM TO 300MM) • PRESSURE CLASS: 150 TO 300 (PRESSURE SEAL 600 TO 2500) Typical Cast Steel Bolted Cover Tilting Disc Check Valve Expanded View

12 11

7 6

4 9

6 8 7

TC9308-3

Note: Classes 600 and larger use internal hinge pin. 1. Body: Cameronâ&#x20AC;&#x2122;s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Cover: The cover allows access to internal components. 3. Cover Gasket: The cover gasket creates a leak-proof seal between the bonnet and body. 4. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the valve, then precision ground for optimal seating. 5. Disc: The disc allows unidirectional flow and restricts back flow with trouble free shutoff. 6. Plug Gasket: The plug gasket creates a leak-proof seal between the plug and body. 7. Plug: The disc nut and pin secures the disc to the arm. 8. Hinge Pin: The hinge pin provides a stable mechanism for the disc to operate. 9. Hinge Pin Washer: The hinge pin washer provides accurate disc positioning. 10. & 11. Cover Studs and Nuts: The cover studs and nuts secure the bonnet to the body. 12. Eyebolt: The eyebolt is used to aid in lifting the valve.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 150 - Sizes: 2.5” to 12” Pressure Class Range: 150 to 300 (See Pressure Seal To 2500) Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Eye bolts are on sizes 5” and larger Hinge pin, plug, and gasket details

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

Body Cover

CB4/2

ASTM A216-WCB ASTM A105/A216-WCB

Disc

ASTM A216-WCB/13% Chrome

Seat Ring

ASTM A182-F316/ ASTM A351-CF8M ASTM A182-F316/ ASTM A351-CF8M w/HF

ASTM A216-WCB/HF

ASTM A105/HF

*Cover Gasket Hinge Pin Hinge Pin Washer Plug Gasket Name Plate Cover Bolts Cover Nuts Plug Eye Bolt 5â&#x20AC;? and larger

Spiral Wound 304 Stainless Steel/Graphite ASTM A479-410 ASTM A479-410 304 Stainless Steel/Graphite 304 Stainless Steel ASTM A193-B7 ASTM A194-2H ASTM A105 ASTM A108-1020

ASTM A193-B7M ASTM A194-2HM

Class 150 Size A-RF A-BW B RF Wt. BW Wt.

NPS

2.5

100

150

200

250

300

In mm In mm In mm Lbs Kg Lbs Kg

8.5 216 8.5 216 8.27 210 42 92 30 66

9.5 241 9.5 241 7.5 190 68 150 50 110

11.5 292 11.5 292 7.3 185 92 202 78 172

14.0 356 14.0 356 9.0 230 174 383 136 299

19.5 495 19.5 495 13.8 350 302 664 244 537

24.5 622 24.5 622 15.4 390 477 1049 376 827

27.5 699 27.5 699 16.1 410 655 1441 464 1021

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 300 - Sizes: 3” to 12” Pressure Class Range: 150 to 300 (See Pressure Seal To 2500) Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Eye bolts are on sizes 5” and larger Hinge pin, plug, and gasket details

Center of Port

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

Body Cover

CB4/2

ASTM A216-WCB ASTM A105/A216-WCB

Disc

ASTM A216-WCB/13% Chrome

Seat Ring

ASTM A216-WCB/HF

ASTM A105/HF

*Cover Gasket Hinge Pin Hinge Pin Washer Plug Gasket Name Plate Cover Bolts Cover Nuts Plug Eye Bolt 5â&#x20AC;? and larger

Spiral Wound 304 Stainless Steel/Graphite ASTM A479-410 ASTM A479-410 304 Stainless Steel/Graphite 304 Stainless Steel ASTM A193-B7 ASTM A194-2H ASTM A105 ASTM A108-1020

ASTM A182-F316/ ASTM A351-CF8M ASTM A182-F316/ ASTM A351-CF8M w/HF

ASTM A193-B7M ASTM A194-2HM

Class 300 Size A-RF A-BW B RF Wt. BW Wt.

NPS

100

150

200

250

300

In mm In mm In mm Lbs Kg Lbs Kg

12.5 318 12.5 318 6.5 165 82 180 57 125

14.0 356 14.0 356 7.3 185 122 268 78 172

17.5 444 17.5 444 8.8 224 252 554 168 370

21.0 533 21.0 533 13.4 340 386 849 278 612

24.5 622 24.5 622 15.2 385 568 1250 458 1008

28.0 711 28.0 711 17.7 450 818 1800 690 1518

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

VI. CAST STEEL BOLTED BONNET STOP CHECK VALVES SIZES: 2” TO 14” (50MM TO 350MM) • PRESSURE CLASS: 150 TO 1500 Typical Cast Steel Bolted Bonnet Stop Check Valve Expanded View 16 17

14 8 7 10

12 2

13 11 20

3 18

20 1 4

Vent

TC9308-3

1. Body: Cameronâ&#x20AC;&#x2122;s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Bonnet: Cameronâ&#x20AC;&#x2122;s NEWCO bonnet assemblies are built to the same standards as the bodies. 3. Back Seat: The back seat, when engaged with the stem head, provides a stable shut-off to the stuffing box which isolates the packing from flow exposure. 4. Stem: The stem inserts vertically into the disc. 5. Disc: The 1-piece vented disc is machined to the tightest tolerance to ensure trouble free shut-off and cycling. 6. Disc Nut: The disc nut serves as a mechanical guide acting on the stem to ensure proper alignment of the disc to the seat. 7. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 8. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments. 9. & 10. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 11. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet. 12. Packing: The packing creates a seal above the back seat between the bonnet and stem. 13. Stuffing Box: The stuffing box contains the packing. 14. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 15. Handwheel: The handwheel cycles the valve. 16. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 17. Handwheel Washer: The washer helps to prevent loosening or distributes pressure evenly. 18. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 19. & 20. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the body. 21. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the valve, then precision ground for optimal seating. 22. Disc Guide: The disc guides provide a stable track for keeping the disc aligned with the seat during cycling.

TC9308-3

Optional gear operator and vertical handwheel.

B (open)

A-BW

A-RF

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A216-WCB Spiral Wound 316 Stainless Steel/Graphite ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B ASTM A105/HF** N/A ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) N/A

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 150 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

150

125

150

200

250

300

350

In mm In mm In mm In mm Lbs Kg Lbs Kg

8.0 203 8.0 203 14.9 378 8.0 203 51 23 51 23

8.5 216 8.5 216 15.8 401 10.0 254 73 33 73 33

9.5 241 9.5 241 16.6 422 10.0 254 93 42 93 42

11.5 292 11.5 292 19.9 505 12.0 305 137 62 137 62

14.0 356 14.0 356 21.8 554 14.0 356 192 87 192 87

16.0 406 16.0 406 22.4 569 16.0 406 243 110 243 110

19.5 495 19.5 495 26.5 673 18.0 457 419 190 419 190

24.5 622 24.5 622 30.6 777 22.0 559 507 276 507 276

27.5 699 27.5 699 34.8 884 24.0 610 948 476 948 476

31.0 787 31.0 787 41.4 1052 25.2 640 1276 625 1276 625

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice. ** Integral seat w/HF for sizes 2” to 4”. TC9308-3

Optional gear operator and vertical handwheel.

B (open)

A-BW

A-RF

TC9308-3

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A216-WCB Spiral Wound 316 Stainless Steel/Graphite ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B ASTM A105/HF** N/A ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) N/A

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 300 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

150

125

150

200

250

300

350

In mm In mm In mm In mm Lbs Kg Lbs Kg

10.5 267 10.5 267 16.9 429 10.0 254 75.0 34 55 25

11.5 292 11.5 292 17.8 452 10.0 254 100.0 45 79 36

12.5 318 12.5 318 19.2 488 12.0 305 130.0 59 101 46

14.0 357 14.0 357 23.0 584 14.0 356 203.0 92 163 74

15.75 400 15.75 400 27.4 696 14.0 406 294.0 134 242 110

17.5 445 17.5 445 30.6 777 18.0 457 421.0 191 355 161

22.0 559 22.0 559 36.2 919 24.0 610 715 325 566 257

24.5 622 24.5 622 40.8 1036 24.0 610 1015 461 770 350

28.0 711 28.0 711 47.3 1201 27.0 686 1500 682 1218 554

33.0 838 33.0 838 54.3 1379 28.3 720 2446 1112 1996 907

Styles: CB2, CB3 and CB4/2 Class: 600 - Sizes: 2â&#x20AC;? to 8â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B Integral ASTM A216 WCB/HF N/A ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 600 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

2.5

100

150

200

203

In mm In mm In mm In mm Lbs Kg Lbs Kg

11.5 292 11.5 292 18.4 467 10.0 254 90 41 79 36

13.0 325 13.0 325 20.0 508 10.0 254 130 59 110 50

14.0 256 14.0 256 24.4 620 14.0 356 170 77 141 64

17.0 435 17.0 435 29.0 737 18.0 457 313 142 256 116

22.0 559 22.0 559 37.9 963 24.0 610 778 354 640 291

26.0 660 26.0 660 44.7 1135 24.0 610 1245 566 961 437

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B Integral ASTM A216 WCB/HF N/A ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 900 Size A-RF A-BW B C RF Wt. BW Wt.

NPS

100

150

200

In mm In mm In mm In mm Lbs Kg Lbs Kg

14.5 368 14.5 368 22.6 574 13.8 350 198 90 176 80

15.0 381 15.0 381 26.0 660 17.7 450 335 152 297 135

18.0 457 18.0 457 30.6 777 17.7 450 440 200 376 171

24.0 610 24.0 610 39.6 1006 22.0 560 1675 761 1144 520

29.0 737 29.0 737 60.1 1527 28.3 720 2090 950 1634 743

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

Styles: CB2, CB3 and CB4/2 Class: 1500 - Sizes: 2â&#x20AC;? to 8â&#x20AC;? Pressure Class Range: 150 to 1500 Design and Manufacturing Standards Valve Design: ASME B16.34/API 600 Flange Dimensions: ASME B16.5, B16.47 (Series A) Face to Face Dimensions: ASME B16.10 Tested in Accordance With: API 598 Recommended Spare Parts*

Optional gear operator and vertical handwheel. B

A-RF

TC9308-3

A-BW

Typical Bill of Materials (See page 89 for available materials) Component

CB2

CB3

CB4/2

ASTM A216-WCB ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 A216-WCB Soft Steel Ring Joint ASTM A194-2H ASTM 193-B7 ASTM A276-410 Graphite W/Braided Carbon Fiber End Rings ASTM A276-410 ASTM A276-WCB ASTM A36 ASTM A194-2H ASTM A307-B Integral ASTM A216 WCB/HF N/A ASTM A666-304 Commercial ASTM A276-410 ASTM A439-D2 ASTM A36 ASTM A36 ASTM A536 (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M ASTM A276-316 ASTM A276-316

ASTM A194-2HM ASTM A193-B7M

ASTM A276-316

Class 1500 Size A-RF A-BW B C RF Wt. BW Wt.

NPS DN In mm In mm In mm In mm Lbs Kg Lbs Kg

2 50 14.5 368 14.5 368 19.6 498 13.8 350 209 95 143 65

3 75 18.5 470 18.5 470 25.6 650 17.7 450 551 250 460 209

4 100 21.5 546 21.5 546 30.8 782 19.7 500 959 436 830 377

6 150 27.75 705 27.75 705 36.5 927 25.2 640 1191 541 996 453

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

VII. CAST STEEL BOLTED BONNET ANGLE STOP CHECK VALVES SIZES: 2” TO 12” (50MM TO 300MM) • PRESSURE CLASS: 150 TO 600 Typical Cast Steel Bolted Bonnet Angle Stop Check Valve Expanded View 16 17

7 12

10 23 2

13 11 20

3 18

20 1 4

TC9308-3

1. Body: Cameronâ&#x20AC;&#x2122;s NEWCO cast steel bodies provide low resistance flow and optimum strength and performance. 2. Bonnet: Cameronâ&#x20AC;&#x2122;s NEWCO bonnet assemblies are built to the same standards as the bodies. 3. Back Seat Bushing: The back seat, when engaged with the stem head, provides a stable shut-off to the stuffing box which isolates the packing from flow exposure. 4. Stem: The stem inserts vertically into the disc. 5. Disc: The 1-piece disc is machined to the tightest tolerance to ensure trouble free shutoff and cycling. 6. Disc Nut: The disc nut serves as a mechanical guide acting on the stem to ensure proper alignment of the disc to the seat. 7. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem. 8. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments. 9. & 10. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression. 11. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet. 12. Packing: The packing creates a seal above the back seat between the bonnet and stem. 13. Stuffing Box: The stuffing box contains the packing. 14. Stem Nut: The stem nut provides a precision guide for proper stem alignment. 15. Handwheel: The handwheel cycles the valve. 16. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly. 17. Handwheel Washer: The washer helps to prevent loosening or distributes pressure evenly. 18. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and body. 19. & 20. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the body. 21. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the valve, then precision ground for optimal seating. 22. Disc Guide: The disc guides provide a stable track for keeping the disc aligned with the seat during cycling. 23. Spacer Ring: The spacer ring assists the packing rings in creating a seal above the back seat between the bonnet and stem.

TC9308-3

B (open)

TC9308-3

CB2

CB3

CB4/2

ASTM A216 GR.WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A276-410 Spiral Wound 316 Stainless Steel/Graphite ASTM A216-WCB ASTM 193-B7 ASTM A194-2H ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A36 ASTM 193-B7 ASTM A276-410 ASTM A216-WCB ASTM A194-2H ASTM A439-D2 ASTM A276-410 ASTM A36 ASTM A36 ASTM A539 Type (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 150 Size A B C D RF Wt.

NPS

DN In mm In mm In mm In mm Lbs Kg

100

150

200

250

300

4.0 107 15.2 386 8 203 6 152 57 26

4.75 121 16.9 429 10 254 7.5 191 84 38

5.75 146 20.4 518 12 305 9 229 141 64

8.0 203 21.8 554 15 381 11 279 234 106

9.75 248 27.4 696 18 457 13.5 343 399 181

12.25 311 31 787 22 559 16 406 611 278

13.75 349 37.8 960 24 610 19 483 794 361

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

B (open)

TC9308-3

CB2

CB3

CB4/2

ASTM A216 GR.WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A276-410 Spiral Wound 316 Stainless Steel/Graphite ASTM A216-WCB ASTM 193-B7 ASTM A194-2H ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A36 ASTM 193-B7 ASTM A276-410 ASTM A216-WCB ASTM A194-2H ASTM A439-D2 ASTM A276-410 ASTM A36 ASTM A36 ASTM A539 Type (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 300 Size A B C D RF Wt.

NPS

100

150

200

250

300

In mm In mm In mm In mm Lbs Kg

5.25 133 15 381 10 254 6.5 165 68 31

6.25 159 16.9 429 12 305 8.25 210 108 49

7 178 21.7 551 14 356 10 254 198 90

8.75 222 28 711 17 432 12.5 318 392 178

11 279 30.7 780 24 610 15 381 560 255

12.25 311 37.5 953 24 610 17.5 445 934 425

14 356 41.6 1049 27 686 20.5 521 1288 586

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

B (open)

TC9308-3

CB2

CB3

CB4/2

ASTM A216 GR.WCB ASTM A105/HF ASTM A276-410 ASTM A216-WCB/HF ASTM A216-WCB/13% Chrome ASTM A276-410 ASTM A276-410 Spiral Wound 316 Stainless Steel/Graphite ASTM A216-WCB ASTM 193-B7 ASTM A194-2H ASTM A276-410 Graphite w/Braided Carbon Fiber End Rings ASTM A36 ASTM 193-B7 ASTM A276-410 ASTM A216-WCB ASTM A194-2H ASTM A439-D2 ASTM A276-410 ASTM A36 ASTM A36 ASTM A539 Type (65-45-12) ASTM A276-410

ASTM A276-316 ASTM A216-WCB/316 ASTM A276-316 ASTM A276-316

ASTM A193-B7M ASTM A194-2HM ASTM A276-316

ASTM A193-B7M ASTM A276-316 ASTM A194-2HM

ASTM A276-316

Class 600 Size A B C D RF Wt.

NPS

2.5

100

150

200

250

In mm In mm In mm In mm Lbs Kg

5.75 146 18.9 480 8.8 224 6.5 165 79 36

6.5 165 20.9 531 9.8 249 7.5 191 110 50

7.0 178 19.8 503 11.0 279 8.3 211 141 64

8.5 216 22.2 564 14.0 356 9.0 229 256 116

11.0 279 28.2 716 17.7 450 14.0 356 640 291

13.0 330 38.5 978 24.8 630 16.5 419 961 437

Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on request. Dimensions are subject to change without notice.

TC9308-3

VIII. HOW TO ORDER ALL CAMERONâ&#x20AC;&#x2122;S NEWCO PRODUCTS Figure Number The figure number shown below identifies specific valve configuration details of Cameronâ&#x20AC;&#x2122;s NEWCO valves such as valve type, pressure class, end connections, body/bonnet and trim materials, and special features. Please specify end connections, body materials and trims not listed below. When placing an order, please refer to the respective product section of the catalog for size availability. A detailed description must be included with any special orders.

TC9308-3

Pressure Class

Type

1 = Gate, OS&Y 2 = Globe/Globe Stop Check, OS&Y 3 = Swing/Tilting Disc Check 4 = Piston Check 5 = Ball 6 = Gate, NRS 7 = Angle/Angle Stop Check, OS&Y

1 = 150 2 = 125 3 = 300 6 = 600 8 = 800 9 = 900 15 = 1500 16 = 1690 25 = 2500 26 = 2680 45 = 4500

End Connections

F = Flanged J = RTJ S = Socket Weld T = Threaded W = Butt Weld X = Threaded x Socket Weld

Trim Material

Fig.18T-FS2 _ _

Suffix Letters

Body/Bonnet Material

A20 = ASTM A351, CN7M = Cast Alloy 20 CB = ASTM A216, WCB = Cast Carbon Steel CC = ASTM A216, WCC = Cast Carbon Steel C5 = ASTM A217, C5 = Cast Alloy Steel (5% Chrome, .5% Moly) C6 = ASTM A217, WC6 = Cast Alloy Steel (1.25% Chrome, .5% Moly) C9 = ASTM A217, WC9 = Cast Alloy Steel (2.25% Chrome, 1% Moly) C12 = ASTM A217, C12 = Cast Alloy Steel (9% Chrome, 1% Moly) 12A = ASTM A217, C12A = Cast Alloy Steel (9% Chrome, 1% Moly, V) CF3 = ASTM A351, CF3 = Cast Stainless Steel C3M = ASTM A351, CF3M = Cast 316L Stainless Steel CF8 = ASTM A351, CF8 = Cast 304 Stainless Steel C7L = ASTM A351, CG3M = Cast 317L Stainless Steel C8M = ASTM A351, CF8M = Cast 316 Stainless Steel C8C = ASTM A351, CF8C = Cast 347 Stainless Steel CT = ASTM A351, CG8M = Cast 317 Stainless Steel DI = ASTM A395 = Cast Ductile Iron FS = ASTM A105 = Forged Carbon Steel F3M = ASTM A182, F316L = Forged 316 Stainless Steel F5 = ASTM A182, F5 = Forged Alloy Steel (5% Chrome, .5% Moly) F7 = ASTM A182, 317 = Forged 317 Stainless Steel F7L = ASTM A182, F317L = Forged 317L Stainless Steel F11 = ASTM A182, F11 = Forged Alloy Steel (1.25% Chrome, .5% Moly) F22 = ASTM A182, F22 = Forged Alloy Steel (2.25% Chrome, 1% Moly) F9 = ASTM A182, F9 = Forged Alloy Steel (9% Chrome, 1% Moly) F91 = ASTM A182, F91 = Forged Alloy Steel (9% Chrome, 1% Moly, V) F8 = ASTM A182, F304 = Forged 304 Stainless Steel F8M = ASTM A182, F316 = Forged 316 Stainless Steel F8C = ASTM A182, F321 = Forged 321 Stainless Steel IB = ASTM A126, CLB = Cast Iron LCC = ASTM A352, LCC = Cast Low Temperature Carbon Steel LF2 = ASTM A350, LF2 = Forged Low Temperature Carbon Steel MO = ASTM A414, M35 = Cast NI Cu (Monel***) SPL = Special (Customer to specify)

TC9308-3

API Trim =

1 = CR13................................ 1, 4, 8A 2 = CR13/HF**.............................8 3 = CR13/FHF**...........................5 4 = 316........................................10 4/2 = 316/HF**..............................12 4/3 = 316/FHF**............................16 5 = NI Cu (Monel***).................9 5/2 = Monel/HF**.........................11 6 = Alloy 20................................13 7 = Bronze................................ N/A A7 = Aluminum Bronze............ N/A 8 = Iron..................................... N/A 9 = Special (Customer to Specify)

BP = By Pass BS = Bellows Seal CL = Chlorine Service CR = Cryogenic Service CW = Chain Wheel EB = Extended Body FP = Full Port FS = Fire Safe GI = Grease Injection GO = Gear Operated HB = Horizontal Ball Check HP = Horizontal Piston Check HO = Hydraulic Operator INT = Integral Flanged LD = Locking Device LL = Locking Loop LV = Live Load Packing MO = Motor Operated NC = NACE MR0103 Compliant OL = Outside Weight & Lever OX = Oxygen Service PO = Pneumatic Operator PS = Pressure Seal Bonnet PT = PTFE Seats QS = QuadroSphere RP = Regular Port SC = Stop Check SL = Spring Loading SPL = Special (Customer to specify) TD = Tilting Disc Check TF = Teflon* Insert TM = Trunnion Mounted VP = Vertical Ball Check VL = Vertical Lift Check VP = V-Port Disc VT = Viton* Insert WB = Welded Bonnet Y = Y Pattern * = Viton and Teflon are registered trademarks of DuPont Company **HF = Hardfaced - AWS 5.13 Class COCRA *** = Monel is a registered trademark of International Nickel Company

IX. INDUSTRY STANDARDS TYPICALLY USED IN VALVE MANUFACTURING (For Reference Only)

British Standards Institute (BS)

ISO 9001: 2000 RWTUV approved NEWCO for design, manufacture, sales, & service of industrial valves under certificate registration number #08-1016 ISO 14001: 2004 The NEWCO/Yancheng Manufacturing Team has passed the TUV-USA ISO 14001-2004 Certification Audit. All facilities inclusive of two (2) Foundries (Lost Wax and Sand Cast), Ball Valve Factory, Final Processing Center and Warehouses 15 & 16.

BS 1414 (1975, R’ 91) - Gate, wedge & double disk valves: steel BS 1868 (1975, R’ 91) - Check valves: steel BS 1873 (1975, R’ 91) - Globe & check valves: steel BS 2080 (1989) obsolete - Flanged & buttweld end steel valves BS 5146 - (withdrawn) Replaced by BS 6755 p.1 steel valves testing (1986) & BS 6755 p.2 (1984) BS 5152 (1974, R’ 91) - Globe & check: cast iron BS 5153 (1974, R’ 91) - Check: cast iron BS 5159 (1974, R’ 91) - Ball: cast iron & carbon steel BS 5160 (1974, R’ 91) - Globe & check: steel BS 5163 (1986, R’ 91) - Gate, wedge & double disk: cast iron BS 5351 (1986, R’ 91) - Ball: steel BS 5352 (1986, R’ 91) - Globe & check: steel BS 5418 - (withdrawn) Replaced by BS EN 19 (1992) marking: general purpose industrial BS 5840 (1980, R’ 91) - Valve mating details for actuator operation BS 6364 (1984, R’ 91) - Cryogenic BS 6683 (1985, R’ 91) - Guide: installation & use of valves BS 6755: Part 1 (1986, R’ 91) - Specification for production pressure testing requirements BS 6755: Part 2 (1987) - Specification for fire type-testing requirements BS EN 19 (1992) - Marking of general purpose industrial valves

American Petroleum Institute (API) API RP 574 (1998) - Inspection practices for piping system components API 589 (1998) - Fire test for evaluation of valve stem packing API RP 591 (2003) - Process valve qualification procedure API 594 (2004) - Check valves-flanged, lug, wafer & buttwelding API 597 (1981) - Steel venturi gate valves, flanged, buttwelding ends API 598 (2004) - Valve inspection & testing API 599 (2002) - Metal plug valves - flanged, welding ends API 601 (1988) - Metallic gaskets for raised-face pipe flanges & flanged connections (doublejacketed corrugated & spiral wound) API 600 (2001) - Bolted bonnet steel gate valves for petroleum & natural as industries “ISO adoption from ISO 10434” API 602 (2005) - Steel gate, globe, & check valves for sizes DN100 and smaller for the petroleum & natural gas industries API 603 (2001) - Corrosion-resistant, bolted bonnet gate valves-flanged & buttweld ends API 604 (1981) - Ductile iron gate valves, flanged ends API 605 (1988) - Large-diameter carbon steel flanges (nominal pipe sizes 26” through 60”, classes 75, 150, 300, 400, 600, & 900 (replaced by ANSI/ASME B16.47) API 606 (1989) - Compact steel gate valves, extended body (included in API 602) fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004” API 607 (2005) - Fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004” API 608 (2002) - Metal ball valves, flanged, threaded, & welding ends API 609 (2004) - Butterfly valves-double flanged, lug- & wafer-type API RP 941 (2004) - Steel for hydrogen service at elevated temperatures & pressures in petroleum refineries & petrochemical plants API RP 520 (2000), Part 1 - Sizing, selection & installation of pressure relieving devices in refineries API RP 520 (2003), Part 2 - Sizing, selection & installation of pressure relieving devices in refineries devices in refineries API Spec 6A (2005) - Specification for wellhead & christmas tree equipment API Spec 6D (2005) - Specifications for pipeline valves API Spec 14D (1994) - Specifications for wellhead surface safety valves & underwater safety valves for offshore service API 5B (2004) - Threading, gauging thread inspection of coring, tubing, & line pipe threads API 6AM (2003) - Material toughness API 6FA (1999) - Fire test for valves API 6FC (1999) - Fire test for valves with backseats API 6FD (1995) - Specification for fire test for check valves API Q1 (2003) - Specification for quality programs for the petroleum, petrochemical, & natural gas

Canadian Standards Association B51-97 - Boiler, pressure vessel, & pressure piping code Z245.15-96 - Steel valves CAN3-z299.4-85 (reaffirmed 1997) - Quality assurance program - Category 4 CAN3-z299.3-85 (reaffirmed 1997) - Quality assurance program - Category 3

International Organization for Standardization ISO 5211/1 (2001) - Industrial valves- part-turn actuator attachments ISO 5211/2 (2001) - Part-turn valve actuator attachment-flange & coupling performance characteristics ISO 5211/3 (2001) - Part-turn valve actuator attachment-dimensions of driving components ISO 5752 (1982) - Metal valves for use in flanged pipe systems face-to-face & center-to-face dimensions ISO 9000 (2005) - Quality management systems and fundamentals & vocabulary ISO 10012-1 (1992) - Quality assurance requirements for measuring equipment

Manufacturers Standardization Society

ASNT-TC-1A (1996) - Recommended practice no. SNT-TC-1A 1996

SP-6 (2001) - Standard finishes for contact faces of pipe flanges & connecting-end flanges of valves & fittings SP-9 (r2005) - Spot facing for bronze, iron & steel flanges SP-25 (1998) - Standard marking system for valves, fittings, flanges & unions SP-42 (2004) - Class 150 corrosion resistant gate, globe, angle, & check valves with flanged & buttweld ends SP-44 (2001) - Steel pipeline flanges SP-45 (2003) - Bypass & drain connections SP-51 (2003) - Class 150/w corrosion resistant cast flanges & flanged fittings SP-53 (2002) - Quality standard for steel castings & forgings for valves, flanges, & fittings & other piping components: magnetic particle exam method SP-54 (2002) - Quality standard for steel castings for valves, flanges, & fittings and other piping components: radiographic examination method SP-55 (2001) - Quality standard for steel castings for valves, flanges other piping components-visual method for evaluation of surface irregularities SP-60 (2004) - Connecting flange joint between tapping sleeves & tapping valves SP-61 (2003) - Pressure testing of steel valves SP-65 (2004) - High pressure chemical industry flanges & threaded stubs for use with lens gaskets SP-67 (2000A) - Butterfly valves SP-69 (2003) - ANSI/MSS edition pipe hangers & supports, selection & application SP-70 (1998) - Cast iron gate valves, flanged & threaded ends SP-71 (1997) - Gray iron swing check valves, flanged & threaded ends SP-72 (1999) - Ball valves with flanged or butt-welding ends for general service SP-79 (2004) - Socket-welding reducer inserts SP-81 (2001) - Stainless steel, bonnetless, flanged knife gate valves SP-82 (1992) - Valve pressure testing methods SP-84 (1990) - Valves - socket welding & threaded ends SP-85 (2002) - Cast iron globe & angle valves, flanged & threaded ends SP-86 (2002) - Guidelines for metric data in standards for valves, flanges, fittings & actuators SP-88 (r2001) - Diaphragm valves SP-91 (1992) - Guidelines for manual operation of valves SP-92 (1999) - MSS valve user guide SP-93 (r2004) - Quality standard for steel castings & forgings for valves, flanges & fittings & other piping components- liquid penetrant exam method SP-94 (r2004) - Quality standard for ferritic & martensitic steel castings for valves, flanges, & fittings and others piping components - ultrasonic exam method SP-96 (r2005) - Guidelines on terminology for valves & fittings SP-98 (2001) - Protective coatings for the interior of valves, hydrants, & fittings SP-99 (r2005) - Instrument valves SP-101 (r2001) - Part-turn valve actuator attachment-flange and driving component dimensions & performance characteristics SP-102 (r2001) - Multi-turn valve actuator attachment: flange and driving component dimensions & performance characteristics SP-110 (1996) - Ball valves threaded, socket-welding, solder joint, grooved, & flared ends SP-117 (2002) - Bellows seals for globe & gate valves SP-118 (2002) - Compact steel globe and check valves-flanged, flangeless, threaded & welding ends (chemical & petroleum refinery service) SP-120 (2002) - Flexible graphite packing system for rising stem steel valves (design requirements) SP-121 (R2002) - Qualification testing methods for stem packing for rising stem steel valves

American Society for Testing and Materials (ASTM)

National Association of Corrosion Engineers (NACE)

American Society of Mechanical Engineers (ASME) ASME Code (1997 addenda) - Boiler & pressure vessel code ASME A13.1 (1996) - Scheme for the identification of piping systems ASME B1.1 (2003) - Unified inch screw threads, UN, & UNR thread form ASME B1.5 (1997) - ACME screw threads ASME B1.7M (1984) - Nomenclature, definitions, & letter symbols for screw threads ASME B1.8 (1988) - Stub ACME screw threads ASME B1.12 (1987) - Class 5 interference - fit thread ASME B1.20.1 (1983) - Pipe threads, general purpose, inch ASME B1.20.3 (1976) - Dry-seal pipe threads, inch ANSI/ASME B16.1 (1998) - Cast iron pipe flanges & flanged fittings ANSI/ASME B16.5 (2003) - Pipe flanges & flanged fittings: NPS 1/2” through 24” ASME B16.9 (2003) - Factory made wrought steel buttwelding fittings ANSI/ASME B16.10 (2002) - Face-to-face & end-to-end dimensions of valves ASME B16.11 (2001) - Forged fittings, socket welding & threaded ASME B16.20 (1998) - Metallic gaskets for pipe flanges: ring joint spiral wound & jacketed ASME B16.21 (2005) - Non-metallic flat gaskets for pipe flanges ASME B16.25 (2003) - Buttwelding ends ANSI/ASME B16.33 (2002) - Manually operated metallic gas valves for use in gas piping systems up to 125 PSI (sizes NPS 1/2” through 2” ) ANSI/ASME B31.1 (2004) - Power piping ANSI/ASME B31.3 (2004) - Process piping ANSI/ASME B16.34 (2004) - Valves flanged, threaded & welding end ANSI/ASME B16.36 (1996) - Orifice flanges ANSI/ASME B16.38 (1985) - Large metallic valves for gas distribution (manually operated, NPS 2-1/2” through 12”, 125 PSIG maximum) ANSI/ASME B16.42 (1998) - Ductile iron pipe flanges & flanged fittings: classes 150 & 300 ANSI/ASME B16.47 (1996) - Large diameter steel flanges ANSI B17.1 (1967, R’ 89) - Keys & keyseats ANSI B18.2.2 (1987) - Square & hex nuts ASME B31.4 (2002) - Pipeline transportation systems for liquid hydrocarbons & other ammonia & alcohols ANSI/ASME B31.8 (2003) - Gas transmission & distribution piping systems ANSI/ASME B36.10 (2004) - Welded & seamless wrought steel pipe ANSI/ASME B36.19 (2004) - Stainless steel pipe ANSI FCI-2 (1991) - Control valve seat leakage

American Society Non-destructive Test (ASNT)

MR0175 (2005) - Sulfide stress cracking resistant metallic materials for oil field equipment MR0103 (2005) - Materials resistant to sulfide street cracking in corrosive petroleum refining environments

TC9308-3

NOTES:

TC9308-3

VALVES & MEASUREMENT 13127 Trinity Dr. Stafford, Tx 77477 Toll Free 800.231.3505 Tel 281.302.4900 Fax 281.302.4801 Learn more about Cameron’s NEWCO valves at: www.c-a-m.com/newco newco@c-a-m.com

ENVIRONME N

XCELLEN LE CE TA

TH SAFETY AL A HE

HSE Policy Statement At Cameron, we are committed ethically, financially and personally to a working environment where no one gets hurt, nothing gets harmed.

MERON