Aluminium Enclosures with snap-on device
Replacing enclosures in a flash is just a ”click“ away
The requirements from industry for aluminium enclosures:
Installation and replacement ”in a flash“ No need to disassemble the enclosure when exchanging it To protect electronics no need to open the enclosure Gaskets should remain untouched during installation of enclosure
Until now, there have only been fixed solutions:
Replacing conventional enclosures Loosen 4 lid screws and 4 enclosure mounting screws and tighten them again There are 16 screwing procedures
Replacing ROLEC aluCASE enclosures
aluCLIC
Loosen 4 enclosure mounting screws and tighten them again There are 8 screwing procedures
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
The solution from ROLEC is aluCLIC, Aluminium Enclosures with snap-on device
The snap-on device is attached to the surface with 4 screws Locate enclosure on the snap-on device and click it into place Lid fixing screws are hidden on the underside of the base Electronics and gaskets in the unopened enclosure remain protected
Now a flexible solution is available from ROLEC
Step 1 The snap-on device, moulded in robust POM plastic, is mounted with 4 screws
Locate the enclosure on the snap-on device Click it into place That‘s it! Replace an enclosure in seconds
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
aluCLIC
Step 2
Snap-on device with proven spring loaded latch
A recess on the bottom of the enclosure locates the snap-on device (invisible from the front)
The lid fastening screws are located on the backside of the base - an important design advantage
The whole of the front can be used for mounting keypads, switches, displays etc.
The market demands for enclosures are continuously increasing; excellent quality and high IP ratings are now basic features. Focused on the market developments, we have always presented outstanding solutions. However, we do not just rest. Our “passion for enclosures” drives us on to find ever new ideas. With the new aluCLIC enclosures, we have found a totally new way to fasten enclosures. Industrial plugs, which have been proven a million times, gave us the idea to make enclosures which also can be “plugged in”.
aluCLIC
These can be exchanged in seconds - an invaluable benefit.
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
Industrial aluminium enclosures with snap-on device
Sizes:
Advantages: Clicking instead of screwing
ACL 092
90 x 130 x 70 mm
Replacement within seconds
ACL 112
110 x 160 x 70 mm
More space for the electronics
ACL 132
130 x 200 x 70 mm
The complete front of the enclosure can be used The lid is screwed from the bottom
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
aluCLIC
Ingress protection IP 67 - IP 69K on request
Technical Data Enclosures Die-cast aluminium: EN AC-44300 DIN EN 1706 (GD Al Si 12/DIN 1725). 1° mould slope for casting ejection ➔ Internal measures diminishing circulatory towards enclosure bottom by 1°. Backside lid-screws Stainless steel 1.4567, captive Snap-on device Plastic POM, colour similar RAL 9005 Integrated recess 1,7 mm recess in the lid for membrane keypads and front panels. Membrane dimensions for standard powder coated enclosures. Ingress protection IP 67 / EN 60529 On request IP 69K / DIN 40050 Gasket TPE gasket, silicone-free temperature range -40°C up to +120°C. Coating Powder coating, light grey RAL 7035 – special colours on request.
ACL 092 ACL 092
130 103 78
46
54 79
90 63
86
103 78 53
70
1
M5 22.5
82
35
56.5 81.5
63 35
aluCLIC
20 96.5 121.5
122
45
51
12.5
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
Folie/ Keypad +0 121,5 -0.2 x 81,5 +0 -0.2
5 5.
94 119
Ø
(20)
Industrial aluminium enclosures with snap-on device
ACL 112 ACL 112
160 133 108
66
74 99
110 83
116
Ø 5 5.
(34) 124 149 133 108 85
70 1
51
M5
ACL 132 ACL 132
102
35
76.5 101.5
83 49
34 126.5 151.5
152
45
22.5
12.5
Folie/ Keypad +0 151,5 +0 -0.2 x 101,5 -0.2
200 173 148
86
94 119
130 103
156
Ø
1
192
M5 22.5
122
35
96.5 121.5
103 49
54
70 45
51
12.5
166.5 191.5
Knud Wexøe A/S • tlf. 4546 5800 • www.wexoe.dk
Folie/ Keypad +0 121,5+0 -0.2 x 191,5-0.2
aluCLIC
173 148 125
5 5.
(54)
164 189
Individual adaptation We can carry out cost effective modifications to suit your individual design requirements. We are fully equipped to realise any modifications thanks to our CNC milling machines and modern paint line. We deliver “just in time”.
Drilling Milling Powder coating Lacquering Engraving Silk-screen printing Fitting Assembling Packaging
ROLEC Gehäuse-Systeme GmbH Kreuzbreite 2 31737 Rinteln Fon +49 (0) 57 51 - 4003 - 0 Fax +49 (0) 57 51 - 4003 - 50 info@rolec.de www.rolec.de