OWNER’S MANUAL Operating, Safety, and Maintenance Instructions with Parts Lists
CABLE LIFT LIFTGATES
ATTENTION: IT IS IMPORTANT TO FOLLOW THE INSTRUCTIONS SET FORTH IN THIS MANUAL TO ENSURE PROPER OPERATION OF THIS EQUIPMENT.
IMPORTANT: AS FINAL STAGE MANUFACTURER, INSTALLER OF THIS LIFTGATE IS RESPONSIBLE FOR COMPLIANCE WITH ALL PERTINENT STATE AND FEDERAL SAFETY STANDARDS AS WELL AS FOR FOLLOWING RECOMMENDATIONS OF CHASSIS MANUFACTURER.
EAGLE LIFT
3501 South 11th Street Council Bluffs, IA 51501 U.S.A. Phone (712) 322-1111 FAX (712) 328-0026 e-mail: eagle@eagleliftgates.com PART #: 1256000
December 2008
EAGLE LIFT’S LIMITED WARRANTIES EAGLE LIFT LIFTGATES These warranties cover all models of liftgates manufactured by Eagle Lift.
3-YEAR LIMITED WARRANTY Eagle Lift warrants to the original owner that the pump and motor unit used in these products shall be free from defects in material and workmanship for THREE YEARS from the date of purchase. If such a defect appears during the warranty period, Eagle Lift will repair or replace (at its option) these components without charge if applicable claim procedures are followed.
1-YEAR LIMITED WARRANTY As to defects not related to the components specified above, Eagle Lift warrants to the original owner that this product shall be free from defects in material and manufacturing workmanship for ONE YEAR from the date of purchase. If such a defect appears during the warranty period, Eagle Lift will repair or replace (at its option) your product without charge if applicable claim procedures are followed. The product must be properly installed, maintained, and serviced in order to eligible for warranty. The warranties apply only to Eagle Lift manufactured products and exclude add-on attachments and modifications. The warranties do not cover defects or damage to products that have been improperly installed, abused, misused, or damage caused by the carrying of corrosive materials or by reason of an accident. The above stated warranties are exclusive. There are no warranties which extend beyond the above stated warranties. There are no implied warranties of merchantability or fitness for any purpose. Incidental damages and consequential damages are excluded. Claims may be made by contacting an authorized Eagle Lift distributor. Eagle Lift or its authorized representative reserves the right to inspect products claimed to be defective for warranty purposes and dispose of the claim as it sees fit, including repair or replacement. Unauthorized repair or replacement prior to inspection may void the warranty. All products or components claimed to be defective must be returned to the factory for warranty consideration within 30 days of the claim. All items shipped out from the factory for warranty reasons will be sent freight prepaid and all items returned to the factory for warranty must be sent freight prepaid. Labor performed for warranty reasons must be done by an authorized Eagle Lift distributor or by a person or company pre-approved by Eagle Lift in writing.
FOREWORD This manual provides operating procedures to help you obtain efficient and dependable use from your Eagle Lift Liftgate. This manual also contains specifications, maintenance information, safety suggestions, and other general information. Eagle Lift’s policy is one of continuous improvement, and it reserves the right to make changes in design and specifications at any time without notice and without obligation to modify equipment previously built. Please read this manual carefully and understand it before attempting to operate, maintain, or repair your liftgate. Keep this manual with the liftgate for future reference. If at any time you have any questions you should contact your Eagle Lift dealer. The dealer has trained service technicians and Eagle Lift replacement parts to keep your Eagle Lift liftgate in top operating condition at all times. Throughout this manual you will see the following symbol: Symbol:
This is the Safety-Alert
Meaning: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The terms CAUTION!, WARNING!, and DANGER! are used in conjunction with the SafetyAlert Symbol to identify the hazard level for items of personal safety. CAUTION! means hazards or unsafe practices that could result in minor personal injury or product or property damage. WARNING! means hazards or unsafe practices that could result in severe personal injury or death. DANGER! means immediate hazards that will result in severe personal injury or death.
SAFETY FIRST!!! Before using an Eagle Lift Liftgate, you should consult all applicable safety standards and instruct the operator fully in its use. Be sure that all personnel who intend to operate the liftgate read and understand this manual fully and comply with it and all safety standards.
DATE PURCHASED: INSTALLED BY:
OWNER'S INFORMATION GATE SERIAL NUMBER:
TABLE OF CONTENTS MODELS ....................................................................................................................................... 6 INTRODUCTION ........................................................................................................................... 7 GENERAL SPECIFICATIONS AND CAPACITIES....................................................................... 8 38 SERIES................................................................................................................................. 8 46 SERIES................................................................................................................................. 9 48 SERIES............................................................................................................................... 10 50 SERIES............................................................................................................................... 11 LIFTGATE TERMS...................................................................................................................... 12 STANDARD MODELS ............................................................................................................. 12 Figure 1 – Liftgate Terms ..................................................................................................... 12 DOUBLE EAGLE MODELS ..................................................................................................... 13 Figure 2 – Liftgate Terms ..................................................................................................... 13 OPERATING INSTRUCTIONS ................................................................................................... 14 STANDARD MODELS ............................................................................................................. 14 Figure 3 – Platform Diagram ................................................................................................ 14 Figure 4 – Control Switch Example ...................................................................................... 15 DOUBLE EAGLE MODELS ..................................................................................................... 16 Figure 5 – Dump-thru Handle ............................................................................................... 16 Figure 6 – Double Eagle Platform Diagram .......................................................................... 16 Figure 7 – Control Switch Operation..................................................................................... 17 Figure 8 – Storage Latch Side View ..................................................................................... 18 DOCK / FORKLIFT LOADING:................................................................................................... 19 Figure 9 – Platform Drop-away............................................................................................. 19 SPARE TIRE ACCESS ............................................................................................................... 20 Figure 10 – Spare Tire Access Hole Locations .................................................................... 20 SERVICE AND MAINTENANCE................................................................................................. 21 TROUBLESHOOTING GUIDE.................................................................................................... 22 ELECTRICAL WIRING DIAGRAMS ........................................................................................... 23 STANDARD CONTROL........................................................................................................... 23 Figure 11 – Standard Control Diagram................................................................................. 23 OPTIONAL REMOTE CONTROL ............................................................................................ 24 Figure 12 – Optional Remote Control Diagram .................................................................... 24 CABLE REPLACEMENT ............................................................................................................ 25 CABLE REPLACEMENT DIAGRAM .......................................................................................... 27 Figure 13 – Cable Replacement Diagram ............................................................................ 27 DECAL LOCATIONS .................................................................................................................. 28 Figure 14 – Decal Locations................................................................................................. 28 DECALS...................................................................................................................................... 29 Figure 15 – Decals ............................................................................................................... 29 LIFTGATE PARTS BREAKDOWN ............................................................................................. 30 38 SERIES............................................................................................................................... 30 Figure 16 – Liftgate Parts Diagram....................................................................................... 30 Figure 17 – Liftgate Parts List............................................................................................... 31 46 SERIES............................................................................................................................... 32 Figure 18 – Liftgate Parts Diagram....................................................................................... 32 Figure 19 – Liftgate Parts List............................................................................................... 33 48 SERIES............................................................................................................................... 34 Figure 20 – Liftgate Parts Diagram....................................................................................... 34 Figure 21 – Liftgate Parts List............................................................................................... 35
48DE SERIES .......................................................................................................................... 36 Figure 22 – Liftgate Parts Diagram....................................................................................... 36 Figure 23 – Liftgate Parts List............................................................................................... 37 50 SERIES............................................................................................................................... 38 Figure 24 – Liftgate Parts Diagram....................................................................................... 38 Figure 25 – Liftgate Parts List............................................................................................... 39 50 DE SERIES ......................................................................................................................... 40 Figure 26 – Liftgate Parts Diagram....................................................................................... 40 Figure 27 – Liftgate Parts List............................................................................................... 41
MODELS This manual applies to the following series and models of Cable Lift Liftgates:
38 SERIES MODELS E38-48SB, E38-49SB, E38-54SB, E38-58, E38-60, and E38-64 1000 # CAPACITY, 40” MAX BED HEIGHT MODELS E38-72, E38-78, and E38-86 1000 # CAPACITY, 40” MAX BED HEIGHT
38 SERIES for Van Applications MODELS E38-60FV, E38-64FV, E38-60DV, E38-64DV, and E38-64CV 1000 # CAPACITY, 40” MAX BED HEIGHT
38 SERIES for Down Sized Pickups MODELS E38-48, E38-52, E38-54, and E38-58 1000 # CAPACITY, 40” MAX BED HEIGHT
46 SERIES MODEL: E46-64SB 1600 # CAPACITY, 46” MAX BED HEIGHT
48 SERIES MODELS E48-64, E48-72, E48-78, E48-86, and E48-91 1300 # CAPACITY, 48” MAX BED HEIGHT
50 SERIES MODELS E50-78, E50-86, and E50-91 1600 # CAPACITY, 50” MAX BED HEIGHT
DOUBLE EAGLE SERIES MODELS E48-78, E48-86, and E48-91 1300 # CAPACITY, 48” MAX BED HEIGHT MODELS E50-78, E50-86 and E50-91 1600 # CAPACITY, 50” MAX BED HEIGHT
1-800-872-4283
6
INTRODUCTION Thank you for purchasing an Eagle Lift Liftgate. Eagle Lift liftgates are the finest on the market today. In order to provide years of service, it is very important that you operate and maintain your liftgate properly. This manual contains information necessary for the proper operation and maintenance of your cable lift liftgate. If you require service for repairs other than simple routine maintenance, please take your liftgate to an authorized Eagle Lift Servicing Distributor. If you need information for an Eagle Lift Servicing Distributor in your area, please contact us at: Eagle Lift 3501 South 11th Street Council Bluffs, IA 51501 U.S.A. Phone (712) 322-1111 FAX (712) 328-0026 e-mail: eagle@eagleliftgates.com Before operating the liftgate, please study this manual carefully and keep it in a handy place for future reference. Above all remember – SAFETY FIRST! 1. Always stand clear of liftgate when operating. Always make certain FEET and HANDS are clear of space between liftgate and truck when raising, and clear of space between liftgate and ground when lowering. Also, keep clear of lifting linkage (arms) when liftgate is in operation. 2. This is not a passenger lift – DO NOT RIDE! 3.
WARNING! Improper operation can result in serious injury – read operating instructions before use.
4. Any alteration of liftgate voids warranty and may void compliance with Federal Motor Vehicle Safety Standards (FMVSS). 5. Only authorized, properly trained adults should operate this liftgate. 6. When not in use, always store platform in closed position with both storage lock latches secured. 7. Never leave liftgate unattended with parking lights “ON” or key in ignition. 8. Decals must remain on liftgate for safety purposes. Replace any damaged or missing decals immediately. 9. Never exceed rated load capacity. Always center load on platform and as close to truck as possible. 10. Always disconnect negative (–) battery cable terminal when welding on liftgate or truck.
1-800-872-4283
7
GENERAL SPECIFICATIONS AND CAPACITIES 38 SERIES
MODEL: E38-48 E38-49 E38-52 E38-54 E38-58 (IMPORT) E38-58 (DOMESTIC) E38-60 E38-64 E38-72 E38-78 E38-86
OVERALL WIDTH
WIDTH BETWEEN UPRIGHTS
49-inch 49-inch 49-inch 55-inch 55-inch 61 1/4-inch 61 1/4-inch 65 5/8-inch 71 7/8-inch 80 3/8-inch 85 7/8-inch
46 1/2-inch 46 1/2-inch 46 1/2-inch 52 1/2-inch 52 1/2-inch 58 3/4-inch 58 3/4-inch 63 1/8-inch 69 3/8-inch 77 7/8-inch 83 3/8-inch
ALL 38 SERIES MODELS OVERALL HEIGHT TRUCK BED TO BOTTOM OF UPRIGHT MAXIMUM BED HEIGHT RATED LOAD CAPACITY (LIFT AND LOWER)
34-inch 13 1/2-inch 40-inch 1000-lb.
LOAD MUST BE UNIFORMLY SPREAD ABOUT THE PLATFORM CENTER.
HYDRAULIC CYLINDER SIZE PUMP/MOTOR RESERVOIR CAPACITY PUMP OPERATING PRESSURE ELECTRICAL SYSTEM
1-800-872-4283
1 3/4-inch bore 11 3/8-inch stroke Approx. 79 cubic-inch 3300 psi. max 12VDC, 170 amp. max. draw @ 3300 psi
8
46 SERIES
MODEL: E46-64SB
OVERALL WIDTH
WIDTH BETWEEN UPRIGHTS
65 5/8-inch
63 1/8-inch
ALL 46 SERIES MODELS OVERALL HEIGHT TRUCK BED TO BOTTOM OF UPRIGHT MAXIMUM BED HEIGHT RATED LOAD CAPACITY (LIFT AND LOWER)
45-inch 17 1/2-inch 46-inch 1600-lb.
LOAD MUST BE UNIFORMLY SPREAD ABOUT THE PLATFORM CENTER.
HYDRAULIC CYLINDER SIZE PUMP/MOTOR RESERVOIR CAPACITY PUMP OPERATING PRESSURE ELECTRICAL SYSTEM
1-800-872-4283
2 1/2-inch bore 15 1/2-inch stroke Approx. 79 cubic-inch 3300 psi. max 12VDC, 170 amp. max. draw @ 3300 psi
9
48 SERIES
MODEL: E48-64 E48-72 E48-78 E48-86 E48-91
OVERALL WIDTH
WIDTH BETWEEN UPRIGHTS
65 5/8-inch 71 7/8-inch 80 3/8-inch 85 7/8-inch 90 7/8-inch
63 1/8-inch 69 3/8-inch 77 7/8-inch 83 3/8-inch 88 3/8-inch
ALL 48 SERIES MODELS OVERALL HEIGHT TRUCK BED TO BOTTOM OF UPRIGHT MAXIMUM BED HEIGHT RATED LOAD CAPACITY (LIFT AND LOWER)
45-inch 17 1/2-inch 48-inch 1300-lb.
LOAD MUST BE UNIFORMLY SPREAD ABOUT THE PLATFORM CENTER.
HYDRAULIC CYLINDER SIZE PUMP/MOTOR RESERVOIR CAPACITY PUMP OPERATING PRESSURE ELECTRICAL SYSTEM
1-800-872-4283
1 3/4-inch bore 17 3/8-inch stroke Approx. 79 cubic-inch 3600 psi. max 12VDC, 195 amp. max. draw @ 3600 psi
10
50 SERIES
MODEL: E50-78 E50-86 E50-91
OVERALL WIDTH
WIDTH BETWEEN UPRIGHTS
80 3/8-inch 85 7/8-inch 90 7/8-inch
77 7/8-inch 83 3/8-inch 88 3/8-inch
ALL 50 SERIES MODELS OVERALL HEIGHT TRUCK BED TO BOTTOM OF UPRIGHT MAXIMUM BED HEIGHT RATED LOAD CAPACITY (LIFT AND LOWER)
45-inch 17 1/2-inch 50-inch 1600-lb.
LOAD MUST BE UNIFORMLY SPREAD ABOUT THE PLATFORM CENTER.
HYDRAULIC CYLINDER SIZE PUMP/MOTOR RESERVOIR CAPACITY PUMP OPERATING PRESSURE ELECTRICAL SYSTEM
1-800-872-4283
2 1/4-inch bore 17 3/4-inch stroke Approx. 79 cubic-inch 3300 psi. max 12VDC, 180 amp. max. draw @ 3300 psi
11
LIFTGATE TERMS STANDARD MODELS
ITEM 1 2 3 4 5 6 7 8 9 10 11
DESCRIPTION ITEM PLATFORM 12 PLATFORM SUPPORT LINKS 13 PLATFORM UPRIGHT (CBSD) 13a FALSE FLOOR 14 HOUSING UPRIGHT (CBSD) 15 CABLE (RDSD) 16 PARALLEL ARM 17 LIFT ARM 18 STORAGE LATCH (RDSD) PLATFORM LATCH TAB HOUSING COVER
DESCRIPTION MAIN HOUSING CONTROL SWITCH HAND HELD REMOTE CONTROL (optional) HYDRAULIC CYLINDER (inside main housing) HYDRAULIC POWER UNIT (inside main housing) FOLD DOWN LATCH (optional) FOLD-OUT EXTENSION RELAY / ELECTRICAL HARNESS SYSTEM (inside main housing)
Figure 1 – Liftgate Terms 1-800-872-4283
12
DOUBLE EAGLE MODELS
ITEM 1 2 3 4 5 6 7 8 9 10
DESCRIPTION ITEM DESCRIPTION PLATFORM 11 HOUSING COVER PLATFORM SUPPORT LINKS 12 MAIN HOUSING PLATFORM UPRIGHT (CBSD) 13 CONTROL SWITCH FALSE FLOOR 13a (OPTIONAL) HAND HELD REMOTE CONTROL HOUSING UPRIGHT (RDSD) 14 HYDRAULIC CYLINDER (inside main housing) CABLE (RDSD) 15 HYDRAULIC POWER UNIT (inside main housing) PARALLEL ARM 16 FOLD DOWN LATCH LIFT ARM 17 DUMP-THRU HANDLE STORAGE LATCH (CBSD) 18 RELAY / ELECTRICAL HARNESS SYSTEM PLATFORM STORAGE LATCH PIN (inside main housing)
Figure 2 – Liftgate Terms
1-800-872-4283
13
OPERATING INSTRUCTIONS STANDARD MODELS 1. To operate the liftgate, turn the vehicle’s parking lights “ON”. This will activate the electrical system on the liftgate, supplying 12 VDC power. 2. Unlatch left (RDSD) storage latch by lifting up and turning outward.
Figure 3 – Platform Diagram 3. Unlatch right (CBSD) storage latch by lifting up. Manually lower platform down to level position. 4. To lower platform to ground: Press down on control switch. You may stop platform at any desired height by releasing control switch (switch should automatically return to neutral position upon release). 5. To raise platform to truck bed: Lift up on control switch.
1-800-872-4283
14
Figure 4 – Control Switch Example 6. To store gate: Raise platform until level with truck bed. Manually lift platform to closed position. CBSD storage latch will engage latch pin with pressure on platform. Lift and pivot RDSD storage latch onto platform latch pin. 7. When finished using the liftgate, turn the vehicle’s PARKING LIGHTS “OFF”. This will disconnect the power to the liftgate.
1-800-872-4283
15
DOUBLE EAGLE MODELS CAUTION! BEFORE USING LIFTGATE, POSITION DUMP-THRU HANDLE OVER LOCK TAB AND SECURE SNAP HOOK IN LOCK TAB HOLE.
Figure 5 – Dump-thru Handle 1. To operate the liftgate, turn the vehicle’s parking lights “ON”. This will activate the electrical system on the liftgate, supplying 12 VDC power. 2. Unlatch left (RDSD) storage latch by lifting up and turning outward. 3. Unlatch right (CBSD) storage latch by lifting up. Manually lower platform down to level position.
Figure 6 – Double Eagle Platform Diagram
1-800-872-4283
16
4. To lower platform to ground: Press down on control switch. You may stop platform at any desired height by releasing control switch (switch should automatically return to neutral position upon release). 5. To raise platform to truck bed: Lift up on control switch.
Figure 7 – Control Switch Operation 6. To store gate: Raise platform until level with truck bed. Manually lift platform to closed position. CBSD storage latch will engage latch pin with pressure on platform. Lift and pivot RDSD storage latch onto platform latch pin. (See Figure 6.) 7. When finished using the liftgate, turn the vehicle’s PARKING LIGHTS “OFF”. This will disconnect the power to the liftgate.
1-800-872-4283
17
Using Double Eagle as a dump-thru tailgate: CAUTION! BEFORE USING AS A DUMP-THRU TAILGATE, YOU MUST SECURE BOTH STORAGE LATCHES OVER PLATFORM RETENTION PINS.
Figure 8 – Storage Latch Side View 1. Fully raise liftgate platform and secure in closed vertical position. 2. Secure both platform storage latches over platform retention pins. 3. Stand to left (RDSD) of liftgate and clear of platform. a. Disconnect snap hook securing dump-thru handle to lock tab. (See Figure 5) b. Pull outward on dump-thru handle until it clears lock tab. c. Turn dump-thru handle clockwise to release lower edge of liftgate platform. 4. When finished dumping load, return dump-thru handle (turn counterclockwise) onto storage lock tab. Place snap hook into hole of lock tab.
1-800-872-4283
18
DOCK / FORKLIFT LOADING: CAUTION! PLATFORM IS SPRING LOADED AND UNDER CONSIDERABLE COMPRESSION WHEN LOCKED IN DOWN POSITION FOR DOCK LOADING. USE EXTREME CARE WHEN LATCHING AND UNLATCHING TO PREVENT INJURY. CAUTION! USE OF DROP-AWAY IS ONLY FOR LOADING AT DOCKS OR WITH FORKLIFTS. DO NOT STORE PLATFORM IN THIS POSITION!
Figure 9 – Platform Drop-away 1. To place platform in drop-away position (Figure 9): a. Manually lift platform and at same time, lift RDSD platform link support upward at hinge point. This allows keyhole of platform and link support pin to line up. b. Disconnect link support from platform. c. Repeat procedure for CBSD link support. Platform will now drop-away for dock or forklift loading. d. Secure platform with fold-down latch (located near bottom of CBSD upright). 2. When finished loading, release platform from fold-down latch, align keyhole of platform with link support pin, and reconnect link supports to platform.
1-800-872-4283
19
SPARE TIRE ACCESS NOTE: Spare tire access required only on Model E38-58 and E38-60 liftgates. 1. Raise liftgate back into position and lift platform into storage locks. 2. Locate appropriate access opening for vehicle applications (See Figure 10).
Figure 10 – Spare Tire Access Hole Locations 3. Insert spare tire access tool (supplied with vehicle) through proper hole and follow vehicle manufacturer’s instructions for spare tire removal and replacement. 4. Replace plastic plug or main housing cover when finished changing tire.
1-800-872-4283
20
SERVICE AND MAINTENANCE NOTE: Service liftgate every 3 months, or when engine oil is changed on vehicle. A. Preventative and Regular Service: 1. Check pins and retaining rings for wear and damage. CAUTION! REPLACE IMMEDIATELY IF MISSING OR IF ANY SIGN OF WEAR IS OBSERVED. 2. Inspect all pins, shafts, retaining rings, bolts, nuts, and roll pins. CAUTION! REPLACE IMMEDIATELY IF MISSING OR IF ANY SIGN OF WEAR IS OBSERVED. 3. Inspect all welds for cracks or fatigue. If found, repair welds as required (recommend taking to an authorized Eagle Lift distributor). 4. Check oil level in reservoir of pump. a. Proper fluid level is approximately 1” below top of reservoir tank with cylinder fully retracted (platform lowered to ground). b. Fill reservoir with an ISO grade 32 hydraulic oil (equivalent to 10 W). Use a special high viscosity oil in cold weather climates. (Unit shipped with cold weather Hydraulic Oil). 5. Inspect fittings, hoses, pump assembly, and cylinder for leakage. Repair or replace as needed. 6. Inspect all electrical connections for tightness, corrosion, or damage. Make repairs as necessary. a. Check battery terminals for proper connections, tightness, and corrosion. b. Inspect battery cell fluid levels according to manufacturer’s instructions. B. Checklist for Safety Features: 1. Gate does not operate unless parking lights are “ON”. Make sure to shut parking lights “OFF” when finished using liftgate. 2. When stored, safety storage latches hold liftgate platform securely in place. 3. All decals are in place and undamaged.
1-800-872-4283
21
TROUBLESHOOTING GUIDE PROBLEM Load will not hold
Motor rotates but excessive noise
Motor spins but the lift will not raise
POSSIBLE CAUSES
SOLUTION
Dirt in lowering valve or main check
Flush or replace the lowering valve
Valve is electrically being told to stay on
Clean / reseat the check
Bent stern on lowering valve
Correct electrical problem
Motor bearings (ball)
Fix or replace motor
Pump cavitation due to plugged suction screen or lack of breather
Check reservoir breather or suction screen
Lowering valve partially open
a) Flush lowering valve relief valve, OR
Dirt in reservoir
b) Check the suction screen and reservoir breather, OR
Reservoir does not have breather installed c) Check for worn pump or is full of dirt Plugged suction screen or worn pump Motor starts but turns slow and lift is slow or will not raise at all
Battery voltage low at power unit
Check voltage at motor between stud and pump base. If voltage loss in wire, clean, tighten and/or replace. If cables are ok, check at battery or start vehicle to raise the voltage. Replace battery if voltage drop cannot be found
Motor pulling high current, motor bearings lack lubrication
Run power unit with lights of vehicle on. If lights dim excessively, check motor for high current. Lube rear sleeve bearing or replace motor. Replace oil with the proper oil for temperature
Oil too thick or water in oil or motor frozen
Motor solenoid clicks but motor does not run
Gate pivot points rusted
Oil pivots and replace bad parts
Bad connection between output of motor start solenoid and motor input terminal Motor is bad
Check wire/busbar and tighten or replace
Pump is stuck and will not turn Unit does not raise; Motor does not run; OR Bad connection in hot battery cable Motor solenoid does not click
Replace motor Remove motor rotate pump input shaft clockwise; if it will not turn, replace pump Remove and clean battery cable at unit and at battery
Bad ground pump/gate, gate/frame, frame Use volt-OHM meter or a test light to track battery open circuits due to corrosion or broken wires; Check to see if the motor solenoid has power and if the solenoid coated wire is grounded or switched to ground on the manual unit Fuse/circuit breaker blown in power relay or Use volt-OHM meter or a test light to track battery cable open circuits due to corrosion or broken wires; Check to see if the motor solenoid has power and if the solenoid coated wire is grounded or switched to ground on the manual unit
Platform will not lower
Bad switch Bad or wrong motor start solenoid Loose control wiring
Check wire/busbar and tighten or replace Check wire/busbar and tighten or replace Tighten wire
Bad power relay
Replace power relay
Bad control wiring to valve or a bad switch Track down open circuit on both the feed side and the ground side Bent coil tower Check for good ground path thru coil/cartridge interface; Clean rust, corrosion and check coil Rusted pivot points on gate or a stuck Replace valve OR Replace cylinder cylinder
1-800-872-4283
22
ELECTRICAL WIRING DIAGRAMS STANDARD CONTROL
Figure 11 – Standard Control Diagram
1-800-872-4283
23
OPTIONAL REMOTE CONTROL
Figure 12 – Optional Remote Control Diagram
1-800-872-4283
24
CABLE REPLACEMENT (SEE DIAGRAM ON PAGE 27) 1. Removing Damaged Cable(s): a. Lower platform to ground or to a supported surface area. Remove main housing cover and force cylinder completely closed while lever is held in down “lower” position. b. Note how cables are routed before disassembly. c. Loosen cable clamps securing lift cable(s) near base of cylinder. d. Remove snap ring and pin securing lift cable(s) to upper lift arm. Note direction and position of cable thimble opening. e. Pull cable(s) from liftgate. 2. Replacing Cables: a. Road Side (RDSD) Lift Cable: 1. Insert bare cable end over top and down back side of single groove RDSD upright pulley. 2. Attach cable thimble eyelet to upper lift arm with pin and secure with internal snap ring. NOTE: Install eyelet with thimble in same position as old cable. Cable end must face down. (See Figure 13) 3. Thread cable end into frame under RDSD housing pulley and on outside groove (outside groove is groove closest to you standing at rear of vehicle). 4. Thread cable under and back around outside groove of cylinder pulley. 5. Thread cable through cable guide located above cylinder. 6. Allow cylinder to extend 3/8” to 1/2” from complete collapse, and secure. Once cylinder is in correct position, pull cable tight and tighten the two cable clamps near base of cylinder. Do not completely torque the cable clamps at this time. The CBSD cable may require adjustment also. 7. Run the liftgate up and down to ensure proper closing of uprights. 8. When both sides close evenly, torque all cable clamp nuts evenly to: 7.5 ft-lbs.: 38 SERIES 12 ft-lbs.: 48 SERIES 15 ft-lbs.: 46 SERIES, 50 SERIES 9. Lubricate both cables by placing white lithium grease in pulley grooves.
1-800-872-4283
25
b. Curb Side (CBSD) Lift Cable: 1. Insert bare cable end over top and down back side of single groove CBSD upright pulley. 2. Attach cable thimble eyelet to upper lift arm with pin and secure with internal snap ring. NOTE: Install eyelet with thimble in same position as old cable. Cable end must face down. (See Figure 13) 3. Thread cable end into frame under CBSD housing pulley and on inside groove (inside groove is groove farthest from you standing at rear of vehicle). 4. Thread cable over top and back around inside groove of RDSD housing pulley. 5. Insert cable under and back around inside groove of cylinder pulley. 6. Allow cylinder to extend 3/8” to 1/2” from complete collapse, and secure. Once cylinder is in correct position, pull cable tight and tighten two cable clamps near base of cylinder. Do not completely torque the cable clamps at this time. The RDSD cable may require adjustment also. 7. Run the liftgate up and down to ensure proper closing of uprights. 8. When both sides close evenly, torque all cable clamp nuts evenly to: 7.5 ft-lbs.: 38 SERIES 12 ft-lbs.: 48 SERIES 15 ft-lbs.: 46 SERIES, 50 SERIES 9. Lubricate cables by placing white lithium grease in pulley grooves. NOTE: WHEN ADJUSTING CABLES, MAKE SURE CBSD UPRIGHT HOUSING CONTACTS MAIN HOUSING APPROXIMATELY 1/8” BEFORE RDSD UPRIGHT HOUSING. DOUBLE CHECK ROUTING AND ADJUSTMENT OF CABLES. OPERATE LIFTGATE TO MAKE SURE CABLES ARE FREE AND DO NOT RUB ANYWHERE.
CAUTION! NEVER CROSS CABLES AT ANY LOCATION.
1-800-872-4283
26
CABLE REPLACEMENT DIAGRAM
Figure 13 – Cable Replacement Diagram IMPORTANT: POSITION THE CABLE CLAMPS IN THE SAME LOCATIONAL AREA THEY WERE REMOVED FROM. THE SADDLE MUST BE ON TOP WITH THE U-BOLTS UPSIDE-DOWN AS SHOWN IN THE DRAWING. WHEN REPLACING CABLES, THE CABLE REPLACEMENTS MUST MEET OR EXCEED THE MANUFACTURER’S SPECIFICATIONS.
1-800-872-4283
27
DECAL LOCATIONS Every Eagle Lift Liftgate must have all caution and operation decals clearly posted as shown. This manual should remain in vehicle at all times as a guide to proper operation, safety, and maintenance of your liftgate. When ordering replacement decals, give Model and Serial Number of your liftgate.
Figure 14 – Decal Locations
1-800-872-4283
28
DECALS
Figure 15 – Decals
1-800-872-4283
29
LIFTGATE PARTS BREAKDOWN 38 SERIES
Figure 16 – Liftgate Parts Diagram
1-800-872-4283
30
38 SERIES PARTS LIST ITEM 1 1 1a 1a 2 3 4 5 6 7 8 9 10 10a 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25a 25c 25d 26 27 27a 27b 27c 27d 27e 28 29 30 31 32 33 34
PART NO. 4240XXX 44601XX 42409XX 4467XXX 427518X 4299001 4269033 4269004 4222738 42550XX 421000X 4231011 4231010 4275041 4275135 4275134 4275136 4275133 4275028 1734510 4299501 4275112 4275111 4299017 4299036 1190026 1144103 1330115 2901001 2901011 2901111 2901901 31223XX 1300121 1330360 1330330 1330180 1330240 1330325 4250092 4250094 4299401 4299065 4299081 1731289 1474312
DESCRIPTION Platform Assembly (Need Liftgate Make, Model & SN) TPX Steel Platform Assembly (Need Liftgate Make Model, & SN) Aluminum Flip-Over Ramp Assy (Need liftgate Make, Model & SN) TPX Steel Flip-Over Ramp Assy (Need liftgate Make, Model & SN) Alum. Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock, RDSD Platform Spring Lock, CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Ring Pivot/Upper Pulley Pin w/ Retaining Ring Pivot/CBSD Pulley Pin w/ Retaining Ring Link Pivot Pin w/ Retaining Ring RDSD Pulley Pin w/ Retaining Ring Cylinder Pin w/Retaining Ring License Plate Light Fold-Down Latch Kit (Includes Hardware) 4" Double Groove Pulley Assembly, RDSD (Includes Bearing) 3" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 7/32" Dia. x 166" Long (w/ Clamps) Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Hand Held Control) Cylinder Assembly - Complete Cylinder Seal Kit (Not shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not shown) In-Line Flow Control Valve Hydraulic Hose Hydraulic Pump/Motor Assy Reservoir Tank w/ Seal Solenoid Switch Motor 12 VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 4 GA x 25' Electrical Power Cable w/ Terminal Ends 4 GA x 25' Ground Cable w/ Terminal Ends (Not Shown) Decal Set (Not Shown) Handle Cap Set, Red (Includes 3-Latch & 1-Control) (Not shown) Clip Ring Set (Not Shown) Wiring Harness Assembly with Relay 150 Amp Circuit Breaker (Not Shown)
QTY. 1 1 1 1 1 1 1 1 2 1 1 2 2 2 6 3 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Figure 17 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
31
46 SERIES
Figure 18 – Liftgate Parts Diagram
1-800-872-4283
32
46 SERIES PARTS LIST ITEM PART NO. 1 4260192 1 4462164 1a 4290064 2 4275161 3 4299001 4 4269033 5 4269004 6 4222748 7 4255041 8 4210004 9 4232001 10 4231007 10a 4275132 11 4275023 12 4275024 13 4275021 14 4275022 15 4275029 16 1734510 17 4299501 18 4208118 19 4208116 20 4299011 21 4299058 22 1190026 23 1144103 24 1330115 25 2903006 25a 2903011 25c 2903111 25d 2903901 26 3122322 27 1300121 27a 1330360 27b 1330330 27c 1330180 27d 1330240 27e 1330325 28 4250093 29 4250095 30 4299402 31 4299065 32 4299083 33 1731289 34 1474312 35 4499011
DESCRIPTION Platform Assembly , TPX Steel (Includes flip) Platform Assembly ( Need Liftgate Make, Model & SN) Aluminum (Includes flip) Flip-Over Ramp Assembly w/ Brackets, TPX Steel Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock - RDSD Platform Spring Lock - CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Ring Pivot / Upper Pulley Pin w/ Retaining Ring Pivot / CBSD Pulley Pin w/ Retaining Ring Link / Pivot Pin w/ Retaining Ring RDSD Pulley Pin with Retaining Ring Cylinder Pin w/ Retaining Ring License Plate Light Fold Down Latch Kit (Includes Hardware) 4 1/2" Double Groove Pulley Assembly (Includes Bearing) 4" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 5/16" Dia. X 246" Long w/ clamps Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Optional, Hand Held Control) Cylinder Assembly Complete Cylinder Seal Kit (Not Shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not Shown) In Line Flow Control Valve Hydraulic Hose Hydraulic Pump / Motor Assy Reservoir Tank w/ Seal Solenoid Switch Motor 12VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 2 ga. x 30' Electrical Power Cable w/ Terminal Ends 2 ga. x 30' Ground Cable w/ Terminal Ends (Not Shown) Decal Set (Not Shown) Handle Cap Set , Red (Includes 3-Latch, 1-Control) (Not Shown) Clip Ring Set (Not Shown) Wiring Harnes w/ Relay 150 Amp Circuit Breaker (Not Shown) Platform Latch Tab kit with Bolt
QTY 1 1 1 1 1 1 1 2 1 1 2 2 2 4 5 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
Figure 19 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
33
48 SERIES
Figure 20 – Liftgate Parts Diagram
1-800-872-4283
34
48 SERIES PARTS LIST ITEM 1 1 2 3 4 5 6 7 8 9 10 10a 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25a 25c 25d 26 27 27a 27b 27c 27d 27e 28 29 30 31 32 33 34 35
PART NO. 42605XX 44710XX 427514X 4299001 4269033 4269004 4222748 42550XX 421000X 4232001 4231007 4275132 4275023 4275024 4275021 4275022 4275029 1734510 4299501 4208048 4250060 4299011 4299048 1190026 1144103 1330115 2902001 2901011 2901111 2901901 31223XX* 1300141 1330360 1330330 1330180 1330240 1330325 4250093 4250095 4299402 4299065 4299083 1731289 1474312 4499011
DESCRIPTION Platform Assembly (Model & Serial Number Required), TPX Steel Platform Assembly (Need Liftgate Make, Model & SN) Aluminum Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock, RDSD Platform Spring Lock, CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Rings Pivot/Upper Pulley Pin w/ Retaining Ring Pivot/CBSD Pulley Pin w/ Retaining Ring Link Pivot Pin w/ Retaining Ring RDSD Pulley Pin w/ Retaining Ring Cylinder Pin w/Retaining Ring License Plate Light Fold-Down Latch Kit (Includes Hardware) 4 1/2" Double Groove Pulley Assembly, RDSD (Includes Bearing) 4" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 1/4" Dia. x 232" Long (w/ Clamps) Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Hand Held Control) Cylinder Assembly - Complete Cylinder Seal Kit (Not Shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not Shown) In-Line Flow Control Valve Hydraulic Hose Hydraulic Pump/Motor Assy Reservoir Tank w/ Seal (Does Not Fit 48-64 Model Liftgates ,Call For Correct Part) Solenoid Switch Motor 12 VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 2 GA x 30' Electrical Power Cable w/ Terminal Ends 2 GA x 30' Ground Cable w/ Terminal Ends (not Shown) Decal Set (Not Shown) Handle Cap Set, Red (Includes 3-Latch & 1-Control) (Not Shown) Clip Ring Set (Not Shown) Wiring Harness Assembly with Relay 150 Amp Circuit Breaker (Not Shown) Platform Latch Tab kit with Bolt
QTY 1 1 1 1 1 1 2 1 1 2 2 2 4 5 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
Figure 21 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
35
48DE SERIES
Figure 22 – Liftgate Parts Diagram
1-800-872-4283
36
48DE SERIES PARTS LIST ITEM 1 1 1a 2 3 4 5 6 7 8 9 10 10a 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25a 25c 25d 26 27 27a 27b 27c 27d 27e 28 29 30 31 32 33 34
PART NO. 42609XX 4460XXX 1420251 427514X 4299001 4269033 4269004 4222748 42550XX 421000X 4232001 4231007 4275132 4275023 4275024 4275021 4275022 4275029 1734510 4299501 4208048 4250060 4299015 4299048 1190026 1144103 1330115 2902001 2901011 2901111 2901901 31223XX 1300141 1330360 1330330 1330180 1330240 1330325 4250093 4250095 4299406 4299065 4299083 1731289 1474312
DESCRIPTION Platform Assembly, TPX Steel Platform Assembly (Need Liftgate Make, Model, & SN) Aluminum Snap Hook w/ Chain Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock, RDSD Platform Spring Lock, CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Rings Pivot/Upper Pulley Pin w/ Retaining Ring Pivot/CBSD Pulley Pin w/ Retaining Ring Link Pivot Pin w/ Retaining Ring RDSD Pulley Pin w/ Retaining Ring Cylinder Pin w/ Retaining Ring License Plate Light Fold-Down Latch Kit (Includes Hardware) 4 1/2" Double Groove Pulley Assembly, RDSD (Includes Bearing) 4" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 1/4" Dia. x 232" Long (w/ Clamps) Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Hand Held Control) Cylinder Assembly - Complete Cylinder Seal Kit (Not Shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not Shown) In-Line Flow Control Valve Hydraulic Hose Hydraulic Pump/Motor Assy Reservoir Tank w/ Seal Solenoid Switch Motor 12 VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 2 GA x 30' Electrical Power Cable w/ Terminal Ends 2 GA x 30' Ground Cable w/ Terminal Ends (Not Shown) Decal Set-DE (Not Shown) Handle Cap Set, Red (Includes 3-Latch & 1-Control) (Not Shown) Clip Ring Set (Not Shown) Wiring Harness Assembly with Relay 150 Amp Circuit Breaker (Not Shown)
QTY 1 1 1 1 1 1 1 2 1 1 2 2 2 4 5 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Figure 23 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
37
50 SERIES
Figure 24 – Liftgate Parts Diagram
1-800-872-4283
38
50 SERIES PARTS LIST ITEM 1 1 2 3 4 5 6 7 8 9 10 10a 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25a 25c 25d 26 27 27a 27b 27c 27d 27e 28 29 30 31 32 33 34 35
PART NO. 42605XX 44710XX 427514X 4299001 4269033 4269004 4222748 42550XX 421000X 4232001 4231007 4275132 4275023 4275024 4275021 4275022 4275029 1734510 4299501 4208118 4208116 4299011 4299058 1190026 1144103 1330115 2903001 2903011 2903111 2903901 31223XX 1300121 1330360 1330330 1330180 1330240 1330325 4250093 4250095 4299402 4299065 4299083 1731289 1474312 4499011
DESCRIPTION Platform Assembly, TPX Steel Platform Assembly (Need Liftgate Make, Model & SN) Aluminum Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock, RDSD Platform Spring Lock, CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Ring Pivot/Upper Pulley Pin w/ Retaining Ring Pivot/CBSD Pulley Pin w/ Retaining Ring Link Pivot Pin w/ Retaining Ring RDSD Pulley Pin w/ Retaining Ring Cylinder Pin w/Retaining Ring License Plate Light Fold-Down Latch Kit (Includes Hardware) 4 1/2" Double Groove Pulley Assembly, RDSD (Includes Bearing) 4" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 5/16" Dia. x 246" Long (w/ Clamps) Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Hand Held Control) Cylinder Assembly - Complete Cylinder Seal Kit (Not Shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not Shown) In-Line Flow Control Valve Hydraulic Hose Hydraulic Pump/Motor Assy Reservoir Tank w/ Seal Solenoid Switch Motor 12 VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 2 GA x 30' Electrical Power Cable w/ Terminal Ends 2 GA x 30' Ground Cable w/ Terminal Ends (Not Shown) Decal Set (Not Shown) Handle Cap Set, Red (Includes 3-Latch & 1-Control) (Not Shown) Clip Ring Set (Not Shown) Wiring Harness Assembly with Relay 150 Amp Circuit Breaker (Not Shown) Platform Latch Tab kit with Bolt
QTY 1 1 1 1 1 1 2 1 1 2 2 2 4 5 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
Figure 25 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
39
50 DE SERIES
Figure 26 – Liftgate Parts Diagram
1-800-872-4283
40
50DE SERIES PARTS LIST ITEM 1 1 1a 2 3 4 5 6 7 8 9 10 10a 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25a 25c 25d 26 27 27a 27b 27c 27d 27e 28 29 30 31 32 33 34
PART NO. 42609XX 4460XXX 1420250 427514X 4299001 4269033 4269004 4222748 42550XX 421000X 4232001 4231007 4275132 4275023 4275024 4275021 4275022 4275029 1734510 4299501 4208118 4208116 4299015 4299058 1190026 1144103 1330115 2903001 2903011 2903111 2903901 31223XX 1300121 1330360 1330330 1330180 1330240 1330325 4250093 4250095 4299406 4299065 4299083 1731289 1474312
DESCRIPTION Platform Assembly, TPX Steel Platform Assembly ( Need Liftgate Make, Model & SN) Aluminum Snap Hook w/ Chain Torsion Spring Platform Bumper Kit (Set of 4 - Includes Hardware) Platform Spring Lock, RDSD Platform Spring Lock, CBSD Platform Link Assembly Zinc Plated Platform Housing Assembly Housing Cover Parallel Arm Assembly Lift Arm Assembly Cable Locking Pin w/ Retaining Ring Pivot/Upper Pulley Pin w/ Retaining Ring Pivot/CBSD Pulley Pin w/ Retaining Ring Link Pivot Pin w/ Retaining Ring RDSD Pulley Pin w/ Retaining Ring Cylinder Pin w/ Retaining Ring License Plate Light Fold-Down Latch Kit (Includes Hardware) 4 1/2" Double Groove Pulley Assembly, RDSD (Includes Bearing) 4" Single Groove Pulley Assembly (Includes Bearing) Storage Latch Kit (Includes Hardware) Cable Assembly Kit - 5/16" Dia. x 246" Long (w/ Clamps) Audible Safety Alarm (Back-up Alarm) Toggle Switch w/ Boot Control Box w/ 7' Cord (Remote, Hand Held Control) Cylinder Assembly - Complete Cylinder Seal Kit (Not Shown) Cylinder Rebuild Kit (Seals, Piston, Head, Key, Nut) (Not Shown) In-Line Flow Control Valve Hydraulic Hose Hydraulic Pump/Motor Assy Reservoir Tank w/ Seal Solenoid Switch Motor 12 VDC Vent Plug (Reservoir) Single Acting Electric Lowering Valve Assy (Not Shown) 2 GA x 30' Electrical Power Cable w/ Terminal Ends 2 GA x 30' Ground Cable w/ Terminal Ends (Not Shown) Decal Set-DE (Not Shown) Handle Cap Set, Red (Includes 3-Latch & 1-Control) (Not Shown) Clip Ring Set (Not Shown) Wiring Harness Assembly with Relay 150 Amp Circuit Breaker (Not Shown)
QTY 1 1 1 1 1 1 1 2 1 1 2 2 2 4 5 2 1 1 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Figure 27 – Liftgate Parts List *Part numbers apply to liftgates manufactured since 12/08. For liftgates manufactured prior to 12/08, please contact an authorized Eagle Lift distributor for part numbers.
1-800-872-4283
41