Owner’s Manual
FBGxxRM & FBGxxRMPD Fold-A-Vador® Rail Style
10900 Kenwood Road • Cincinnati, OH 45242 Ph: 513.891.6210 • Toll-Free: 866.539.6261 Fax: 513.891.4901 www.leymanlift.com • sales@leymanlift.com
LML00125-9-10-09
TABLE OF CONTENTS Introduction
2
Words of Caution
3
General Terminology
4
Operating The Lift Gate
5
How to Operate The Emergency Hand Pump
6-9
Maintaining the Lift Gate Recommended Hydraulic Oil – Preventative Maintenance Schedule
10 - 11
Trouble Shooting – General Maintenance Troubleshooting chart
12 - 13
Electrical Diagrams – Battery Hook Up – Grounding Recommendations
14 – 29
Proper Manual Valve Setting For Dual Power Unit
30
Maintenance Minder® STARTER Solenoid Switch (with green LED light on starter)
31
Maintenance Minder 2® Controller Menus (orange box inside power unit enclosure)
32 – 34
General Tips
35
Bleeding The Power Fold Cylinder – Lift Cylinders – Gravity and Power Down Gates
36 - 38
Adjustment of The Equalizer Valve - Straightening The Tie Bar
39 - 40
Lubricating The Roller Tracks
41
Parts Replacement Hydraulic Assembly Lift Cylinders – Power Fold Cylinder
42 - 43
Replacement Roller
44 - 45
Platform Pins and Bushings
46
Hand Rails: Standard, Collapsible
47 - 49
Power Units – Hand Pump Assemblies
50 – 74
Safety Decals
75 – 79
Notes
80
Electrical Part Replacement - See Electrical Diagrams (page 14 – 29)
Page 1
INTRODUCTION This manual contains the operating procedures on the equipment your company is using that was manufactured by Leyman Manufacturing Corporation. Past experience has indicated that it is most unwise to operate these units without proper instruction, which should be instituted by the purchaser. While these products have certain safety features engineered into their design, they are all operated by human beings. Therein lies the problem of safety and one should always have caution in mind when operating this or any other machine that has parts that weigh several hundred pounds. Again, let us remind you that there are moving parts on this product that weigh several hundred pounds. These parts, when not under proper control, can cause physical damage to operator. Because of the weights that are involved, carelessness and neglect of training can make these units dangerous. Do not overload this product. Maintain it properly. Stand clear of moving parts. Operate as instructed. This lift gate has a long life expectancy and will take some abuse. Use good judgment when operating this equipment.
PLEASE FILL IN FOR YOUR RECORDS
CUSTOMER: MODEL: CAPACITY: TYPE: POWER: PLATFORM: SERIAL: OPTIONS
_____________________________________ _____________________ ________________________ ______________ 12 VOLT_____ __________________________ __________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________
MAXIMUM HEIGHT: HYDRAULIC PRESSURE: AMP DRAW:
60� LOADED 2,500 PSI AT THE PUMP LOADED 235 UNLOADED 100
POWER UP GRAVITY DOWN OR POWER DOWN
WHEN PLACING PARTS ORDER, YOU WILL NEED THE SERIAL# AND MODEL# OF THE GATE.
Page 2
WORDS OF CAUTION 1.
BEFORE ANY MAINTENANCE IS PERFORMED ON THIS UNIT, READ AND UNDERSTAND THIS MANUAL COMPLETELY.
2.
DO NOT STAND ON OR BEHIND THE PLATFORM WHEN OPERATING GATE IN THE FOLDED POSITION.
3.
DO NOT STAND IN FRONT OF THE PLATFORM WHEN LOWERING FROM VERTICAL POSITION OR OPERATING IN ANY MANNER.
4.
MAKE SURE THE GROUND IS CLEAR UNDER THE PLATFORM WHEN LOWERING.
5.
CHECK THE AREA AROUND THE UNIT FOR ANY PERSONS BEFORE OPERATING THE LIFT GATE.
6.
THIS LIFT GATE SHOULD OPERATE SMOOTHLY AND THE ONLY NOISE THAT SHOULD BE HEARD IS THE POWER UNIT. ANY OTHER AUDIBLE SOUNDS OTHER THAT THE NORMAL POWER UNIT OPERATION SOUND SHOULD BE THOROUGHLY CHECKED AND THE CAUSE OF THE NOISE SHOULD BE LOCATED AND CORRECTED.
7.
NEVER EXCEED THE RATED LOAD CAPACITY OF THIS GATE. DO NOT OVERLOAD MAXIMUN RATED CAPACITY IS BASED ON AN EVENLY DISTRIBUTED LOAD OVER THE PLATFORM FLAT SURFACE. STAY WITHIN THE LOAD CENTER RESTRICTIONS.
8.
ALWAYS LOAD AS CLOSE TO THE CENTER OF THE PLATFORM AND AS CLOSE TO THE CENTER OF THE TRUCK SILL AS POSSIBLE.
9.
DO NOT ALLOW PERSONS TO OPERATE THE UNIT UNLESS THEY HAVE BEEN PROPERLY TRAINED TO DO SO.
10. USE ONLY FACTORY AUTHORIZED PARTS FOR REPLACEMENT.
THIS MANUAL REFLECTS MOST CHANGES AND UPDATES OF MATERIALS THAT ARE COMMON TO THIS TYPE OF LIFT GATE. SOME MAY DIFFER DUE TO INDIVIDUAL CUSTOMER REQUIREMENTS. THIS MANUAL HAS BEEN ESTABLISHED TO REFLECT THE COMMON ITEMS.
WARNING: THIS GATE HAS POLYMER GREASELESS BEARINGS IN THE ROLLERS, PLATFORM PIVOTS, AND CYLINDER. WHEN WELDING, BE SURE TO GROUND DIRECTLY TO THE COMPONENT BEING WELDED.
UNPLUG THE MAINTENANCE MINDER 2速 CONTROLLER TO AVOID ANY DAMAGE TO THE UNIT.
Page 3
GENERAL TERMINOLOGY
Page 4
OPERATION OF THE LIFT GATE Before operating the lift, read and understand the decal, urgent warning decals and the owner’s manual. Do not stand behind the lift gate while unfolding or using the platform. To unfold the platform from the over-the-road position: 1. 2. 3. 4.
Momentarily fold the gate. Push the fold and up switches at the same time, as to ensure the gate is fully folded. To relieve tension on the auto lock, push the up switch (gate will go up), pull the handle to release the auto lock. Lower the platform by pushing the down switch until platform ears are at slots in outer mast. Push the unfold switch (gate will unfold).
To dock load: 1. 2. 3.
To relieve the tension on the auto lock, push the up switch (gate will go up), pull the handle to release the auto lock. Lower the gate until the ears on the platform rest on the stops of the outer mast. WARNING! Never use the platform as a “bridge” to a dock or other vehicle. Platform can fold unexpectedly and cause injury.
To lower platform, use the down switch only. To raise platform, use the up switch only. Safe loading of platform: 1. The cart stop or retention ramp must be in place whenever lifting or lowering a load. Also, see the urgent warning decal. To fold platform: 1. 2.
Raise the platform off the ground about two feet. Push the fold and up switch together using both hands. Platform will fold. Platform ears must pass through slots and go inside masts. Continue to raise the platform to the full up position, auto lock will latch.
Page 5
HOW TO OPERATE THE EMERGENCY HAND PUMP FOR GRAVITY DOWN LIFT GATE Before 4-1-07 Step 1
Inside the power unit enclosure, find the ball valve handle (plastic covered handle). Open the ball valve by turning the handle so that it is parallel with the fitting that connects the hydraulic line to the ball valve.
Step 2 Insert the handle into the pump and jack upward. The gate will rise completely to the up stops. Continue pumping the handle until the gate folds up completely. (Do this until the platform ears are tight against the outer mast). Step 3 Close the plastic covered handle ball valve. Turn the handle so that it is 90 degrees from the fitting that connects the hydraulic line to the ball valve. Step 4 Using the handle, slowly turn the valve (located on the hand pump) to let the gate down until the platform ears go into the notch on the outer mast. Shut the valve. Step 5 Jack the platform up until the gate is completely up and locked in the “over the road� driving position.
OPEN POSITION
CLOSED POSITION
Page 6
HOW TO OPERATE THE EMERGENCY HAND PUMP FOR POWER DOWN LIFT GATE Before 4-1-07 Step 1 Inside the power unit enclosure, open both ball valves (plastic covered handles turned in-line with valve body). Step 2 Insert the hand pump handle and jack the platform up to the full up position. Continue pumping to fold the platform up until the platform ears are tight against the outer mast. Step 3 Close both ball valves (plastic covered handles turned 90 degrees to valve body). Step 4 Using the handle slowly turn the valve (located on the hand pump) counter-clockwise to lower the platform until ears go into the notch on the outer mast. Close valve on the hand pump. Step 5 Open the ball valve located on the reservoir tank only and jack the platform up until the ears engage the auto-lock in the over-the-road driving position.
OPEN POSITION
CLOSED POSITION
Page 7
HOW TO OPERATE THE EMERGENCY HAND PUMP FOR GRAVITY DOWN LIFT GATE After 4-1-07 Step 1
To raise or lower the gate using the hand pump, the ball valve in the REAR next to the filter must be OPEN, and the valve in the FRONT must be CLOSED.
Step 2 To raise, insert the handle into the pump and jack up. To lower, use the end of the handle to slowly open the small valve at the base of the hand pump. Step 3 To fold or unfold the platform using the hand pump, the ball valve in the REAR next to the filter must be CLOSED, and the valve in the FRONT must be OPEN. Step 4 To fold, insert the handle into the pump and jack to fold. To unfold, use the end of the handle to slowly open the small valve at the base of the hand pump. After folding, close ball valve in front to maintain folded position. Step 5 To store gate in transit position, raise platform off the ground about two feet by following Steps 1 and 2 above. Then fold the platform by following Steps 3 and 4 above. Platform ears must pass through slots and go inside masts. Continue raising the platform (Steps 1 and 2) to the full up position until the Auto Locks latch. Step 6 When using the power unit, normal positions for ball valves in the hand pump circuit are – rear valve next to filter OPEN, front valve CLOSED, and small valve at base of hand pump closed (tight clockwise).
OPEN POSITION
CLOSED POSITION
Page 8
HOW TO OPERATE THE EMERGENCY HAND PUMP FOR POWER DOWN LIFT GATE After 4-1-07 Locate all 3 ball valves in the Hand Pump circuit. Follow the chart for proper ball valve settings: Ball Valve on tank In front
Ball Valve above Motor in front
Ball Valve above Filter in rear
RAISE using Hand Pump
OPEN
CLOSE
OPEN
LOWER using Hand Pump
CLOSE
CLOSE
OPEN
FOLD/UNFOLD
OPEN
OPEN
CLOSE
Std. Valve Setting When using Pwr. Unit
CLOSE
CLOSE
OPEN
Step 1 To raise the gate using the hand pump, set the ball vales as given above. Then insert the handle into the hand pump and jack up. Step 2 To lower the gate using the hand pump, set the ball valves as given above. Then use the end of the handle to slowly open the small valve at the base of the hand pump. Step 3 To fold the platform using the hand pump, set the ball valves as given above. Insert the handle into the hand pump and jack to fold. Then close ball valve in front above motor to maintain folded position. Step 4 To unfold the platform using the hand pump, set the ball valves as given above. Then use the end of the handle to slowly open the small valve at the base of the hand pump. Step 5
To store gate in transit position, position the platform about two feet off the ground by following Steps 1 or 2 above. Then fold the platform by following Step 3. Platform ears must pass through slots and go inside masts. Continue raising the platform (Step 1) to the full up position until the Auto Locks latch.
Step 6 Return ball valves to the Standard Valve Setting given above.
OPEN POSITION
CLOSED POSITION
Page 9
MAINTAINING THE LIFT GATE
RECOMMENDED HYDRAULIC OILS HYDRAULIC OILS
MANUFACTURER
TYPE
TEMP. RANGE
Level 1 Normal Conditions
Mobile Shell Chevron Mobile Shell Chevron
DTE 11 TELLUS-T15 RYKON ISO-15 AERO-HFA AERO FLUID#4 AVIATION-A
-15° F to + 150° F -15° F to + 150° F -15° F to + 150° F -50° F to + 80° F -50° F to + 80° F -50° F to + 80° F
Level 2 Cold Conditions
HYDRAULIC TANK CAPACITY 2 ½ gallons
LUBRICATION Grease Hinge Barrels (center platform) Dry Lubricant
Militec #1 W.W. Grainger – Part #6Y834 – Needle Nose Adapter ZEP45 (do not use corrosive lubricants like WD40, etc.) Dri Slide Multi-Purpose Lube (produced by Lubritek)
LIFT GATE SPECIFICATION BATTERIES Two (2) 12 V D.C. Group 31 Heavy Duty lead acid Dual Purpose, or AGM
ELECTRICAL COMPONENTS CONNECTIONS Use battery terminal protection Bowman Part#21948
AMPERAGE DRAW OF MOTOR When raising platform (empty) approximately 100 AMPS @ 13.5 volts. At bypass approximately 235 AMPS @ 13.5 volts
LIFTING PRESSURE SETTING With platform at floor level and pump in bypass 2500PSI
MINIMUM VEHICLE FLOOR HEIGHT LADEN With main platform 36” – vehicle floor height 40” With main platform 42” – vehicle floor height 46”
MAXIMUM VEHICLE FLOOR HEIGHT UNLADEN With main platform 36” – vehicle floor height 60” With main platform 42” – vehicle floor height 60”
APPROXIMATE TIMES EMPTY AT 80° F WITH 2 GROUP 31 BATTERIES Time up: 24 – 28 seconds Time down(gravity down): 12 –14 seconds Time down(power down): 16 – 18 seconds
Page 10
PREVENTATIVE MAINTENANCE SCHEDULE MAINTENANCE by CYCLES FBG MODELS DATE: CUSTOMER LOCATION VEHICLE #
GATE MODEL # GATE SERIAL # SERVICED BY
v = OK 3000
X = REPAIR
A = ADJUSTED
MOTOR / PUMP COMPONENTS
N = NOT APLICABLE
3000
MOTOR / PUMP COMPONENTS Check charge line/power line for corroded, loose or broken connections Check amp draw of motor with fully charged batteries and tight clean connections Check all ground wires for corroded, loose or broken connections Check pressure setting of relief valve Clean all wiring connections in pump and battery box and spray with Bowman #21948 connection protection or equivalent Check charge line/power line for corroded, loose or broken connections at both ends Dual power units, run secondary unit for proper operation
3000
STRUCTURAL COMPONENTS Remove hydraulic guard for fold cylinder line and check for loose/missing clamps, frayed lines and proper alignment Check lift gate for proper operation up and down Check lift gate for proper operation folding and unfolding
Check batteries for corroded, loose or broken connections Check batteries for proper voltage level and charging Check all wiring in pump box for corroded, loose or broken connections Check poppet solenoids for proper operation Check reservoir for proper oil level “Gravity Down” (Gate open and down on the ground, 1” from top of tank) Check reservoir for proper oil level “Power Down” (Gate open and up at floor level, 1” from top of tank) Inspect circuit breakers and fuses for proper operation Check all fittings/hoses in power unit for tightness and leaks 3000
STRUCTURAL COMPONENTS Check switches for proper operation, check connections for tightness and corrosion Check all fittings/hoses on cylinders for tightness and leaks Check fold cylinder for leaks/worn packing Check for broken/missing roll pins at rollers, fold cylinder, primary/secondary platform pin Check snap rings on lift and fold cylinder pins Check for broken/missing torsion bar assembly at platform Check aluminum platform for loose bolts on side brackets and threaded plugs at hinge pins
3000
LUBRICATION Grease primary and secondary platform pin at grease holes with #1 lithium grease Grease power unit door hinge pins with #1 lithium grease Grease rollers with #1 lithium grease (if shafts are equipped with grease fittings) DO NOT use grease in roller tracks.
Screen 1 # Lifts
Check for impact damage on inner/outer masts Check for broken/missing bolts at platform pins Check and re-weld any cracked/broken welds Replace all safety and warning labels as needed PERIODICAL CHECK LIST 12000
Check all pivot point bushings for wear or damage
15000
Flush hydraulic system and change hydraulic oil Clean and repaint as necessary
MAINTENANCE MINDER2® READINGS MENU 2 Screen 3 Service Faults Screen 4 Low Voltage Faults
Screen 6 High Temperature Faults
Check owner’s manual for proper hydraulic oil, motor amp draw and pressure setting of power unit Rev. 5-13-09
Page 11
TROUBLE-SHOOTING – GENERAL MAINTENANCE TROUBLE SHOOTING CHART The following troubleshooting chart covers the standard power unit (12 volt power unit) used with the FBG.
PROBLEM Platform will not go up or reach the floor of the vehicle.
Platform will not lower.
Platform does not go up smoothly.
PROBABLE CAUSE 1. 2.
3. 4. 1. 2. 3.
Battery is low. Slave line is disconnected or connections are loose (battery and motor). Insufficient oil in power unit tank.. Poor switch connections. Battery is low. Poor switch connections. Check lowering valve.
1. 2. 3. 4.
Insufficient oil in power unit tank. Air lock in hydraulic system. Dirt or foreign material in guides. Mechanical wear.
REMEDY 1. 2. 3. 4.
Recharge the battery. Connect the slave line properly. Fill the power unit tank. Clean and check switch connections.
1. 2.
Recharge the battery. Clean and check switch connections. Clean/replace as necessary. Fill tank. Run platform to stop. Open up bleeders in each ram while power unit is running. Close bleeders and refill the tank. Clean guides with steam and check for excessive wear, obstructions, and burrs. Replace worn parts. Check all hoses and fittings. Replace ram seals. Clean/replace as necessary.
3. 1. 2.
3.
Platform creeps down.
Platform goes down slowly.
1. 2. 3.
4. 1. 2. 3.
Platform goes up crooked.
1. 2. 3.
Hydraulic leak. Ram seals failing. Dirt under the ball of check valve, the ball is pitted or worn or the spring is weak. Check lowering valve. Excessive wear of mechanical components. Restriction in hydraulic system. Incorrect hydraulic oil in system for cold weather. Equalizer valve is out of adjustment. Air trapped in one of the rams. Tie bar is bent.
4. 1. 2. 3.
1. 2. 3. 1. 2. 3.
Insure free movement of all mechanical parts. Check all hydraulic system components. Use Mobile Aero-HFA in cold weather. Adjust equalizer valve. Bleed air out of the ram. Straighten the tie bar.
Page 12
TROUBLE SHOOTING CHART
The following troubleshooting chart covers the standard power unit (12 volt power unit) used with the FBG.
PROBLEM Platform comes down crooked.
PROBABLE CAUSE 1. 2. 3. 4.
Gate will not lift the rated load. Pump will not operate.
1. 2. 1. 2. 3. 4.
5.
Dirt in flow control, not adjustable. Dirt in hydraulic line at the bottom of the ram. Mechanical bind on one (1) side of gate. Tie bar is bent. Hydraulic pump is worn. Battery is too low. Battery too low. Electrical hookup to motor not making contact. Control switches are not making good contact. Maintenance Minder solenoid has shut down the system due to low voltage condition. Maintenance Minder 2 controller has shut down the system due to low voltage. Must maintain 8 volts minimum under load.
REMEDY 1. 2. 3.
4. 1. 2. 1.
2. 3. 4. 5.
Clean/replace flow control as necessary. Clean hydraulic line and bleed ram. Clean and inspect inner mast and rollers. Check wear of parts and replace if necessary. Straighten tie bar. Change the pump. Recharge the battery to full charge. Recharge the battery and check to be sure that the slave line has a good connection. Clean connections and re-tighten. Clean and check the connections. Recharge battery. 9.5 volts must be maintained under load. Use the “Last Lift Menu” to read maximum and minimum voltages. Recharge battery.
Page 13
ELECTRICAL DIAGRAM GRAVITY DOWN SPX / FENNER POWER UNIT (gold motor) with Smart Start solenoid (before 4/03)
Page 14
ELECTRICAL DIAGRAM GRAVITY DOWN MONARCH POWER UNIT (black motor) with MAINTENANCE MINDER 2速 (after 4/03)
Page 15
ELECTRICAL DIAGRAM POWER DOWN SPX / FENNER POWER UNIT (gold motor) with Smart Start速 solenoid (before 4/03)
Page 16
ELECTRICAL DIAGRAM POWER DOWN MONARCH POWER UNIT (black motor) with MAINTENANCE MINDER 2速 (after 4/03)
Page 17
WALK AROUND ELECTRICS GRAVITY DOWN
DOWN
UP
WALK AROUND ELECTRICS FOR GRAVITY DOWN – BEFORE 3-06
Page 18
WALK AROUND ELECTRICS GRAVITY DOWN WALK AROUND ELECTRICS FOR GRAVITY DOWN – AFTER 3-06
Page 19
ELECTRIAL DIAGRAM GRAVITY DOWN DUAL POWER UNIT – WALK AROUND
Page 20
WALK AROUND ELECTRICS POWER DOWN
DOWN
UP
WALK AROUND ELECTRICS FOR POWER DOWN – BEFORE 3-06
Page 21
WALK AROUND ELECTRICS POWER DOWN WALK AROUND ELECTRICS FOR POWER DOWN – AFTER 3-06
Page 22
ELECTRICAL DIAGRAM POWER DOWN DUAL POWER UNIT – WALK AROUND
Index No. 1 2 3 4 5 6 7 8 9 10 11 12
Req. 1
Part No. BA-551-359
Description PWR DN Walk Around Sub Assy
3
P46476
Locking Fork Terminal
1 1 1 6
AA-551-326 P46475 P46443 P46156
Toggle Switch Assembly Cable 16-6 Cable 16-5 Butt Connector
1 1 6
P46250 P17518 P46319
Loom Clamp Self Tapping Screw Lrg. Fork Terminal
Comments
16-6 x 30” 16-5 x 25”
Page 23
SWITCH WIRING GRAVITY DOWN RM SERIES
LEGEND G – GREEN W – WHITE B – BLACK O – ORANGE R – RED B - BLUE
REPLACEMENT SWITCHES ARE SUPPLIED WITH THE NECESSARY HARDWARE TO CONNECT INTO THE EXISTING WIRING.
Index No. 1 2 3 4 5 6 7 8 9
Req. 1 1 1 1 1 1 10 1 1
Part No. AA-551-519 AA-551-520 BP-805-256 BP-805-258 P46746 P46443 P17518 P46445 P46139
Part Name POTTED OUTER TWO SW. ASSY POTTED INNER SINGLE SW ASSY RECESSED SWITCH PLATE
Matl.
Remarks
16-3 16-5
10 FT. (120”) 40 FT. (480”)
RECESSED SINGLE SWITCH PLATE
JACKETED WIRE – HIGH FLEX JACKETED WIRE SELF TAPPING SCREW CORD GRIP CORD GRIP
IN OUTER MAST IN INNER MAST
Page 24
SWITCH WIRING POWER DOWN RMPD SERIES
LEGEND G – GREEN W – WHITE B – BLACK O – ORANGE R – RED B - BLUE
REPLACEMENT SWITCHES ARE SUPPLIED WITH THE NECESSARY HARDWARE TO CONNECT INTO THE EXISTING WIRING.
Index No. 1 2 3 4 5 6 7 8 9
Req. 1 1 1 1 1 1 10 1 1
Part No. AA-551-521 AA-551-522 BP-805-256 BP-805-258 P46747 P46475 P17518 P46445 P46139
Part Name POTTED OUTER TWO SW. ASSY POTTED INNER SINGLE SW ASSY RECESSED SWITCH PLATE
Matl.
Remarks
16-4 16-6
10 FT. (120”) 40 FT. (480”)
RECESSED SINGLE SWITCH PLATE
JACKETED WIRE – HIGH FLEX JACKETED WIRE SELF TAPPING SCREW CORD GRIP CORD GRIP
IN OUTER MAST IN INNER MAST
Page 25
CONNECTING GATE ELECTRICS - GRAVITY DOWN DUAL POWER UNIT with COMMON OIL TANK
ROUTE THE CABLE FROM THE GATE ELECTRICS INTO THE POWER UNIT ENCLOSURE AND CONNECT THE WIRE TERMINALS TO THE CENTER COLUMN OF THE SELECTOR SWITCHES. MATCH COLOR TO COLOR ACROSS THE ROWS FOR PROPER OPERATION. NOTE: THE SELECTOR SWITCHES BRACKET CAN BE UNBOLTED FROM THE ENCLOSURE TO MAKE THE CONNECTIONS EASIER TO ACCESS. CABLE FROM SECONDARY POWER UNIT CONNECTS TO LEFT SIDE
CABLE FROM GATE SWITCHES CONNECTS TO CENTER ROW CABLE FROM PRIMARY POWER UNIT CONNECTS TO RIGHT SIDE
CONNECTIONS VIEWED FROM REAR GREEN NOT USED BLACK WHITE ORANGE RED
POWER UNIT SELECTOR SWITCHES SWITCHES FACING RIGHT: RH (SECONDARY) POWER UNIT OPERATES
CAUTION! SWITCHES MUST BE POSITIONED BOTH TO THE LEFT OR BOTH TO THE RIGHT FOR PROPER OPERATION. WALK AROUND CONTROL OPERATES RH (SECONDARY) POWER UNIT ONLY
PRIMARY POWER UNIT GATE SWITCHES SECONDARY POWER UNIT
SWITCHES FACING LEFT: LH (PRIMARY) POWER UNIT OPERATES
Page 26
CONNECTING GATE ELECTRICS – POWER DOWN DUAL POWER UNIT with COMMON OIL TANK
ROUTE THE CABLE FROM THE GATE ELECTRICS INTO THE POWER UNIT ENCLOSURE AND CONNECT THE WIRE TERMINALS TO THE CENTER COLUMN OF THE SELECTOR SWITCHES. MATCH COLOR TO COLOR ACROSS THE ROWS FOR PROPER OPERATION. NOTE: THE SELECTOR SWITCHES BRACKET CAN BE UNBOLTED FROM THE ENCLOSURE TO MAKE THE CONNECTIONS EASIER TO ACCESS. CABLE FROM SECONDARY POWER UNIT CONNECTS TO LEFT SIDE
CABLE FROM GATE SWITCHES CONNECTS TO CENTER ROW CABLE FROM PRIMARY POWER UNIT CONNECTS TO RIGHT SIDE
CONNECTIONS VIEWED FROM REAR GREEN BLUE BLACK WHITE ORANGE RED
POWER UNIT SELECTOR SWITCHES
CAUTION! SWITCHES MUST BE POSITIONED BOTH TO THE LEFT OR BOTH TO THE RIGHT FOR PROPER OPERATION. WALK AROUND CONTROL OPERATES RH (SECONDARY) POWER UNIT ONLY
SECONDARY POWER UNIT
SWITCHES FACING RIGHT: RH (SECONDARY) POWER UNIT OPERATES
PRIMARY POWER UNIT GATE SWITCHES
SWITCHES FACING LEFT: LH (PRIMARY) POWER UNIT OPERATES
Page 27
BATTERY HOOK UP We recommend batteries with the following specifications: 12 Volt heavy duty lead acid Dual Purpose or AGM B.C.I. Group – Size 31 Terminal Type – TS Cold Cranking Amps - 580
One Circuit Breaker Wiring Diagram
"O" GAUGE POWER LINE FROM CHARGING SOURCE TO CENTER LUG. CIRCUIT BREAKER #1 PROTECTS BATTERIES AND MOTOR.
CIRCUIT BREAKER
STARTER SOLENOID ON MOTOR
BATTERY
BATTERY
GROUND BATTERIES TO VEHICLE FRAME AND GROUND TRAILER SOCKET TO COMPLETE CHARGING CIRCUIT
FOR MONARCH POWER UNIT (BLACK MOTOR) CONNECT NEGATIVE BATTERY TERMINAL TO CAP SCREW ON PUMP BLOCK
FAILURE TO USE CORRECT BATTERIES WILL VOID WARRANTY
Page 28
GROUNDING RECOMMENDATIONS FOR TRACTOR/TRAILER
The Maintenance Minder速 requires a minimum of 9.5 volts in order for the FBG to operate. Utilization of a single positive cable does not provide sufficient ground. Therefore, our recommendation for grounding tractor/trailers with a FBG gate are as follows: Two (2) cables one: (1) positive and one (1) negative, both running to the tractor batteries. The MAINTENANCE MINDER 2速 controller requires that a minimum of 8 volts be maintained under load in order for the FBG to operate. NOTE: The use of a battery charger as the sole power source to operate a FBG is unauthorized and will prevent the FBG from working properly. The lift gate must always be operated in conjunction with at least one (1) 12-volt heavy-duty lift gate battery. A minimum of 9.5 volts must be maintained in order for the valves to operate.
Page 29
PROPER MANUAL VALVE SETTINGS FOR DUAL POWER UNIT
PROPER MANUAL VALVE SETTINGS FOR DUAL POWER UNIT
PRIMARY POWER UNIT
TOP MANIFOLD BLOCK
SECONDARY POWER UNIT
PRIMARY POWER UNIT OPERATING - OPEN BOTH "P" VALVES, CLOSE BOTH "S" VALVES SEC. POWER UNIT OPERATING - OPEN BOTH "S" VALVES, CLOSE BOTH "P" VALVES
PUSH IN
PUSH IN
TO OPEN
AND RELEASE
TO CLOSE
Page 30
MAINTENANCE MINDER速 STARTER SWITCH Before 4-1-03 SYMPTOM LED on start switch does not glow.
PROBABLE CAUSE Poor ground
Poor positive connection
Battery voltage below 9 volts Voltage at the start switch is below 9 volts
LED on start switch glows then goes off when attempting to operate lift gate.
Faulty switch Poor ground
Battery voltage below 9 volts Excessive voltage drop
CORRECTION Check for proper ground, remove any paint or corrosion that may be inhibiting a good ground between the lug or the brown wire and the grounded surface. Check for a loose connection at the red wire. Charge the battery. Check the supply cable between the battery and the switch for loose connections and/or corrosion. Replace the start switch. Check the battery ground and the switch ground (brown wire) for good connections. Charge the battery. Increase the battery cable size between the battery and the Maintenance Minder速 .
Page 31
MAINTENANCE MINDER 2® CONTROLLER MENUS Power unit is equipped with the Maintenance Minder 2® Controller. It will: • Automatically keep track of maintenance intervals and warn the user when maintenance is due, based on the number of lifts. • Record low voltage occurrences. • Record of high temperature faults. • Record of maximum run time faults, when a single operation exceeded the maximum continuous run time limit. • Give helpful trouble-shooting information on MENU 4, “Last Lift Info”. FAULTS CODES A decal in the power unit enclosure lists the following signal codes for these faults: 1 BEEP 2 BEEPS 3 BEEPS 4 BEEPS
Service Fault (reached the number of lifts when maintenance is due) Low Voltage Fault (check battery condition and power line connections) Max. Time Fault (exceeded the maximum continuous run time allowed) High Temperature Fault (unit will not run until motor cools)
All fault signals will be repeated FOUR times except the Service Fault, which will be given just once. Controller will prevent power unit from operating during the time period when a fault signal is sounding (about 5 to 10 sec.) The controller is also equipped with an anti-doorbelling feature, which prevents rapids ON/OFF operation of the power unit. RESETTING after MAINTENANCE IS PERFORMED To RESET the Maintenance Minder 2® after maintenance has been performed: 1. Go to MENU 2, hit “ENTER”, and toggle down to the “Reset All Info” screen. 2. Press and hold the hidden RESET button under Maintenance Minder 2® logo at top of faceplate. 3. Follow the instructions on the screen regarding a second button, which must be pressed to complete the reset operation.
Page 32
MAINTENANCE MINDER 2® CONTROLLER MENUS
(Press MENU) MENU 1 – LIFT GATE INFO (Press ENTER, then ARROW DOWN for each item) Model Number, Serial Number, Manufacture Date, Vehicle ID, Hardware Version, Firmware Version, Software Version.
(Press MENU and ARROW DOWN once) MENU 2 – PERIOD INFO (data for current maintenance period) (Press ENTER, then ARROW DOWN for each item) Number of Lifts (gives the number during this maintenance interval and the set number when maintenance is due) Motor ON (total motor run time in minutes for this maintenance period) Service Fault (number of times gate was operated while PAST the maintenance limit) Max. Time Faults (times motor exceeded its maximum allowable continuous run time) High Temperature Faults (times thermal switch in motor tripped, if switch provided) Low Voltage Faults (times low voltage occurred) Reset all Info (Reset data after performing maintenance, once maintenance limit is reached – follow instructions for Resetting after Maintenance is PERFORMED.
Page 33
MAINTENANCE MINDER 2® CONTROLLER MENUS
(Press MENU and ARROW DOWN twice)
MENU 3 – LIFE TIME INFO (data for the total life time of the gate) (Press ENTER, then ARROW DOWN for each item) Same items will appear, as under PERIOD INFO, except this is LIFE TIME data. Reset History (reviews history for each maintenance interval) Press ENTER, then ARROW DOWN to show history. Most recent period is highest#. Screen shows Period #, # of Lifts, and Total Run Time in minutes.
(Press MENU and ARROW DOWN three times) MENU 4 – LAST LIFT INFO (Trouble Shooting Screen – it records data that occurred during the last lift made)
(Press ENTER, then ARROW DOWN for each item) Supply Voltage (first voltage is the minimum voltage that occurred during the last lift – if below 6 volts gate will stop / second voltage is the supply voltage just before gate operation, must be at least 10 volts). Motor ON (motor run time in seconds during last lift, gate will stop at 180 seconds). Window Time (time in milliseconds during the last lift that the voltage dropped in between 6 and 8 volts – must not be any longer than 3 seconds or gate will stop).
NOTE: Controller has an anti-doorbelling feature. Motor will not operate if UP switch is toggled rapidly. This prevents welding of the start solenoid contacts.
Page 34
GENERAL TIPS LIFT GATE 1. This gate can run up or down uneven from the vehicle floor by 1” to 1 ½” without damaging the mechanical workings on the gate. 2. The equalizer valve is only for adjus ting the up stroke (while the gate is loaded). 3. The flow control valves are for controlling the down stroke only. They should be cleaned and/or changed in sets. 4. Determining if the tie bar is bent: Raise the platform to its full up position (level to the ve hicle floor). Push the down switch. If the tie bar is bent, one side will always drop quicker than the other. If you have a bent tie bar, it is best to straighten it. See this manual for information on how to straighten the tie bar. Before adjusting or attempting to fix any of the four items above, check the following first: a. Check the cylinder rods for lubrication. Dry rods may cause sticking or slow down the movement of the gate. b. Check for bent inner mast. c. Check to see if the back edge of the platform is hitting the floor level tube. d. Check to see if the inner mast is rubbing on the outer mast. Some hitting is normal, but if it hinders the up/down operation, it must be lubricated. 5. Premature motor failure is almost always caused by low batteries. 6. Inadequate grounding is also a major reason for motor failure. POWER UNIT 1. If the motor runs and the gate does not rise, you may have one of the these problems: a. The Emergency Hand Pump Valve is open (or partially open). b. You have a bad pump. c. Manual valves are closed (dual power unit only). 2. To get the gate down, energize the two-way valve (white wire). The motor will not run in this operation. 3. To get the gate up, push one of the switches up. No valves must be shifted. The motor will run. 4. To unfold the platform, energize the two -way valve (orange wire). The motor will not run in this operation. 5. To fold the platform, energize the three-way valve (red wire). You must push the fold switch and the up switch. The motor will run. 6. If the unit has an emergency hand pump and the gate goes up, hits the up stops and the platform starts to fold, the ball valve is open (or partially open). To correct this, close the ball valve. 7. The pressure setting with platform at floor level and pump in bypass is 2500 PSI.
Page 35
TO BLEED THE POWER FOLD CYLINDER 1. Unfold and lower the platform down to the ground. 2. Loosen the hose at the cylinder but do not remove completely. 3. Activate the pump (just long enough to product an air free stream of oil from the hose). 4. Re-tighten the hose and check the oil level in the reservoir tank. Note: hold line while tightening to ensure it does not twist. 5. Fold and unfold the platform several times. The platform should now fold and unfold smoothly.
Clamps located inside guard on outer mast.
Clamp located inside guard on inner mast.
The electric line is routed along the hydraulic line to match the loop. When re-attaching the lines, ensure that there is no "twist" in the line. "Twist" in the line can cause uneven or erratic tracking.
CHECK OIL LEVEL AFTER BLEEDING THE CYLINDER: GRAVITY DOWN GATES – Check with platform unfolded and on ground. POWER DOWN GATES – Check with platform unfolded and up at bed height.
Page 36
BLEEDING THE LIFT CYLINDERS - GRAVITY DOWN The FBG is shipped with the cylinders pre-filled with hydraulic fluid from the factory. The cylinders must be bled before making any other adjustments. To Bleed the Lifting Cylinder – Bottom Side: 1. Unfold and lower the platform to the full down position. CYLINDERS SHOULD BE EXTENDED TO THEIR FULL LENGTH (GATE EXTENDED DOWN 56”) TO REMOVE AS MUCH AIR FROM THE BOTTOM SIDE OF THE CYLINDER AS POSSIBLE. DEPENDING ON THE FLOOR HEIGHT OF THE VEHICLE, IT MAY BE NECESSARY TO RAISE THE BODY OF THE VEHICLE OR LOWER THE GATE PLATFORM INTO A PIT TO ACHIEVE MAXIMUM CYLINDER EXTENSION. 2. Loosen the plugs in the back ports (ports closest to the vehicle body), but do not remove completely. 3. Activate the pump just long enough to produce an air-free stream of oil from the ports. 4. Re-tighten the plugs in the ports, lower the platform to the full down position, and check the oil level in the reservoir tank. The oil level should be approximately 1” from the top of the tank, except for DUAL UNITS with individual plastic tanks where oil level should be 2” from top of tank. Add oil if necessary. On DUAL UNITS with individual plastic tanks, allow time for oil level to equalize between tanks. To Bleed the Lifting Cylinders – Top Side 1. Not applicable on gravity down. NOTE: FOR GRAVITY DOWN GATES, OIL LEVEL SHOULD ALWAYS BE CHECKED WITH THE PLATFORM UNFOLDED AND ALL THE WAY DOWN.
Back Port: This port will allow air out from the lifting (bottom) side of the cylinder. Front Port: This port will have no oil for Gravity Down gates.
Page 37
BLEEDING THE LIFT CYLINDERS – POWER DOWN The FBG is shipped with the cylinders pre-filled with hydraulic fluid from the factory. The cylinders must be bled before making any other adjustments. To Bleed the Lifting Cylinder – Bottom Side: 1
Unfold and lower the platform to the full down position. CYLINDERS SHOULD BE EXTENDED TO THEIR FULL LENGTH (GATE EXTENDED DOWN 60”) TO REMOVE AS MUCH AIR FROM THE BOTTOM SIDE OF THE CYLINDER AS POSSIBLE. DEPENDING ON THE FLOOR HEIGHT OF THE VEHICLE, IT MAY BE NECESSARY TO RAISE THE BODY OF THE VEHICLE OR LOWER THE GATE PLATFORM INTO A PIT TO ACHIEVE MAXIMUM CYLINDER EXTENSION. 2. Loosen the plugs in the back ports (ports closest to the vehicle body), but do not remove completely. 3. Activate the pump just long enough to produce an air-free stream of oil from the ports. 4. Re-tighten the plugs in the ports, raise the platform to the full up position, and check the oil level in the reservoir tank. The oil level should be approximately 1” from the top of the tank except for DUAL UNITS with individual plastic tanks where oil level should be 2” from top of tank. Add oil if necessary. On DUAL UNITS with individual plastic tanks, allow time for oil level to equalize between tanks. To Bleed the Lifting Cylinders – Top Side 1. Unfold and raise the platform to the full up position to remove as much air from the top side of the cylinder as possible. 2. Loosen the plugs in the front ports (ports furthest from the vehicle body) but do not remove completely. 3. Activate the pump just long enough to produce an air-free stream of oil from the ports. 4. Retighten the plugs in the ports, raise the platform to the full up position if not already there, and check the oil level in the reservoir tank. The oil level should be approximately 1” from the top of the tank, except for DUAL UNITS with individual plastic tanks where oil level should be 2” from top of tank. Add oil if necessary. On DUAL UNITS with individual plastic tanks, allow time for oil level to equalize between tanks. NOTE: FOR POWER DOWN GATES, OIL LEVEL SHOULD ALWAYS BE CHECKED WITH THE PLATFORM UNFOLDED AND RAISED ALL THE WAY UP. Back Port: This port will allow air out from the lifting (bottom) side of the cylinder. Front Port: This port will allow air out from the power down (top) side of the cylinder.
Page 38
ADJUSTMENT OF THE EQUALIZER VALVE NOTE: Before making any adjustments, read the general tips page to be sure this is the problem. Remember adjusting the equalizer valve will control the up stroke only. Locate the equalizer valve. Stand on the unfolded platform, look at the back of the truck/trailer. The equalizer valve is about 4 inches below the floor line and to the left of center. Back off the lock nut on the side that is running slow (lagging) turn the adjusting screw out Âź turn, lock nut and try. Repeat if necessary. Although this can be done with no load on the platform, it normally helps to have a light load on the platform. NOTE: Turn the adjusting screw in = decreases the flow of oil Turn the adjusting screw out = increases the flow of oil Units shipped after 7/08 have a High Accuracy Equalizer Valve. We do NOT recommend adjusting these valves.
TO DRIVERS SIDE CYL
TO CURB SIDE CYL
LOCKING NUT ADJUSTING SCREW
TO POWER UNIT
Page 39
STRAIGHTENING THE TIE BAR NOTE: Before bending the tie bar, read the general tips page to be sure this is the problem. To check that you have a bent tie bar, raise the platform to the full up position (level to the floor). Push the down switch, one side will always drop quicker than the other side. If one side is lower by more than one inch (1”), adjust the tie bar. The tie bar is at the back edge of the platform. It is 1 ½” wide, and holds the two inner masts together. Acquire a piece of wood 4” x 4” x 2’ long and place the wood between the tie bar and the up stop area near the floor line area. Caution! Check for cracked welds before proceeding. Stand clear while performing this procedure. NOTE: If the curbside is dropping first, place the wood on the driver’s side. Run the gate up until the wood is secure, keep running the gate up another 6 to 8 inches. Let the gate down, remove the wood, cycle the lift gate to see if this has fixed the problem. If not, re-bend, except go up another inch or two. Keep repeating until corrected. Sometimes, the power from the gate is not enough to correct the problem. If you have a hand pump, use it to take it up further. If you do not have a hand pump, use a floor jack and continue jacking the gate in an upward cycle. PICTURE SHOWS HOW TO STRAIGTHEN A BENT TIE BAR ON CURBSIDE. (CURB SIDE DROPS QUICKER) CURB SIDE
STAND CLEAR
WOOD BLOCK
BEND TO STRAIGHTEN
Page 40
LUBRICATING THE ROLLER TRACKS Do NOT use grease or oil to lubricate the roller tracks. Wet lubricants will allow dirt and grit to stick and cause premature wear.
If lubrication is necessary, use Dri-Slide dry lubricant from Lubritek.
Page 41
PARTS REPLACEMENT –
HYDRAULIC ASSEMBLY
Index No.
Qty Req’d
Part Number
Part Name
Remarks
1 2 3 4 5 6 7 8 8 9 10 11 12 13 14 15 16
2 1 1 1 1 4 2 2 2 8 6 4 1 4 4 4 4
P33931 See chart See chart See chart See chart P33006 P33064 P33619 P33914 P46251 P17518 P46497 P33547K AA-811-328 P43577 P34014 P31048
Hyd. Cylinder Hydraulic line assy (incl. item 15) Hydraulic line assy (incl. item 15) Hydraulic line assy (incl. item 15) Hydraulic line assy (incl. item 15) Street elbow 3/8 Nipple Pipe 3/8 Flow control 2.8 GPM Flow control 2.0 GPM Loom clamp ¾ in. Self tapping screw ¾” Split loom Equalizer with adapter fittings (incl. item 15) Cylinder Pin with 2 snap rings Cylinder Mounting Block Bearing Straight Adapt. 3/8 NPT(M) – 9/16-18 JIC(M) Plug, Pipe 3/8 SHCS
54 Stroke RH Lifting LH Lifting RH “Down” Line LH “Down” Line
Gravity Down Power Down Not Shown Not Shown 24” Lg ea. SAE “O” Ring Ports Not Shown Not Shown
Grav Dn Assy
Power Dn Assy
Gate Width
Qty Req’d
RH Lifting Item 2
LH Lifting Item 3
RH “Down” Line Item 4
LH “Down” Line Item 5
CT-819-084-002 CT-819-084-001
CT-819-035-002 CT-819-035-001
102” 96”
1 ea. 1 ea.
BT -501-442-129 BT -501-442-123
BT -501-442-085 BT -501-442-085
BT -501-442-093 BT -501-442-093
BT -501-442-131 BT -501-442-125
Page 42
POWER FOLD ASSEMBLY
Index No. 1 2 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Qty. 1 1 1 1 1 1 1 1 1 2 1 1 4 2 2 1 1 1
Part No. P33877 P33915 P33646 P33064 P33217 P33671 P33750 AT-501-284-074 AP-811-200 P24019 S754-005.500 P47532 P26019 P46462 P46750 P34174 P34106 P34110
Description Hyd. Cylinder Breather Vent - 1/8 NPT Breather Vent – 3/8 NPT Pipe Nipple Male Elbow (used when cylinder port is recessed) Flow Control – steel platform Adapter (Qty. 2 if using elbow block) Hose Assembly Top Ram MTG Shaft Retaining Ring Bottom Ram MTG Pin Roll Pin Washer Cable Tie 11” Stainless Steel Cable Tie Spring Guard Bulkhead Elbow Straight Adapter
Page 43
REPLACEMENT ROLLER 4” REPLACEMENT UPPER ROLLER PARTS GREASED / GREASELESS ROLLERS WITH SIDE PADS
ROLLER ASSEMBLY CAN BE ORDERED COMPLETE UNDER PART NO. BA-818-435 OR BY INDIVIDUAL COMPONENTS LISTED BELOW. NOTE: FLAT WASHER P26517 WAS USED WITH PREVIOUS SHAFT BP-805-297-1. IT IS NO LONGER NEEDED WITH SHAFT BA-805-300 OR BA-805-304.
Index No. 1 2 3 4 5
Qty Req’d 1 1 2 1 1
Part Number BA-818-196 BA-805-304 P43565 P47507 P32016
Part Name Roller Sub Assembly Roller Shaft Assy. Thrust Bearing Roll Pin Grease Fitting
Page 44
REPLACEMENT ROLLER 4” REPLACEMENT LOWER ROLLER PARTS GREASED / GREASELESS ROLLERS WITH SIDE PADS
ROLLER ASSEMBLY CAN BE ORDERED COMPLETE UNDER PART NO. BA-819-175 OR BY INDIVIDUAL COMPONENTS LISTED BELOW. Index No. 1 2 3 4 5 6 7
Qty Req’d 1 1 2 2 1 1 1
Part Number BA-818-382 BA-819-177 P24021 P43565 P47507 P26517 P32016
Part Name Roller Sub Assembly Roller Shaft Assy. Retaining Ring Thrust Bearing Roll Pin Flat Washer Grease Fitting
Page 45
PLATFORM PINS AND BUSHINGS
PLATFORM BEARING (1 REQ’D EACH SIDE)
Index No. 1 2 3 4 5 6 7 8 9
Qty. 2 2 1 2 1 1 1 1 2
Part Number P11048 P26017 BA-818-205 P26020 S790-060.000 AP-808-108 S055-002.000 BA-818-206 P43567
Part Name Bolt Washer Lock Split 3/8 Pin Sub Assy Spacer Washer Torsion Bar Hex Sleeve Mtg. Plate Pin Sub Assy Platform Bearing
Material Size/Notes 3/8 16 x 1 ¼ gr. 8 Driver Side 60” lg
Curb Side
Page 46
Hand Rail Parts Standard Hand Rails
Index No.
Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
2 6 2 2 2 2 4 2 2 2 2 2 2 2 2 1 1 2 1 2
Part Number AA-811-384 P26517 P24021 BA-811-363 AA-811-383 P26020 P47514 CA-811-371 S758-020.250 P47508 S403-000.250 BA-811-362 S149-002.500 BP-811-385 S498-002.500 BP-999-045 AA-999-021 AP-811-459 S057-007.000 S192-001.750
Part Name Spacer – Double Barrel Washer Retaining Ring Side Rail –Front Pin for FBG Narrow Rim Washer Roll Pin Front Rail Assembly Shaft Roll Pin Spacer Side Rail – Back Flat Platform Ear Rail Stop Sign Plate Chain Assembly Pin for Std Hand Rail Spacer Stop Block
Material Size/Notes
¼ x 1-1/2
For ear on platform
Not shown
For platform ear For Front Rail Assembly
Page 47
Hand Rail Parts Collapsible Hand Rails
Page 48
Hand Rail Parts Collapsible Hand Rails Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Qty. 6 2 2 2 2 4 2 2 2 2 2 2 2 2 1 2 2 2 1 2 2 2 2 2 2 2 2 2
Part Number P26517 P24021 BA-811-363 AA-811-383 P26020 P47514 CA-811-373 S758-020.250 S403-000.250 BA-811-364 AP-811-377 S149-002.500 BP-811-385 S498-002.500 AA-999-012 P17518 P56577 P29020 S057-007.000 BA-811-362 S413-000.500 S192-001.750 P26004 S777-000.875 P25201 BP-811-367 P47521 BP-811-368
Part Name Washer Retaining Ring Side Rail – Front Pin for FBG Narrow Rim Washer Roll Pin Front Rail Assembly Shaft Spacer Front Side Assembly Spacer Flat Platform Ear Rail Stop Chain Assembly Self Tapping Screw Lanyard Assembly Hair Spring Cotter Pin Spacer Side Rail - Back Spacer Stop Block Washer Spring Spacer Spring Pin Roll Pin Handle
Material Size/Notes
¼ x 1-1/2 Includes items 23 - 28 Not shown
For ear on platform (not shown)
For platform ear (not shown) For Front Side Assembly For Front Rail
Page 49
POWER UNIT PARTS SPX POWER UNIT
Page 50
POWER UNIT PARTS MONARCH POWER UNIT
FILTER P33616 – before 9-1-04 FILTER P34046 – after 9-1-04
STARTER P34016 TEMP. SWITCH P34054
BREATHER CAP LH150015
(THRU 5/07 for Bosch Motors.) Temp Switch not Avail. for Prestolite motors.
MOTOR P34027A
GROUND WIRE
O-RING P34099
PUMP P34056
TANK P34033
COMPLETE SINGLE POWER UNIT LESS FILTER P33994B “A” VALVE (white wire, back) P33954 “B” VALVE (orange wire, back) P33956 “C” VALVE (red wire, front) P34063
COMPLETE DUAL POWER UNIT LESS FILTER P34012A “A” VALVE (white wire, top) P33954 “B” VALVE (orange wire, top) P33956 “C” VALVE (red wire, back) P34036 – before 6-1-05 “C” VALVE (red wire, back) P34063 – after 6-1-05 Dual Tank P34074 Manual Isolation valve (4) per unit P34075
Page 51
POWER UNIT ASSEMBLY SPX POWER UNIT - GRAVITY DOWN
Page 52
POWER UNIT ASSEMBLY SPX POWER UNIT - GRAVITY DOWN
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Qty. 1 2 2 8 3 2 1 1 2 1 1 2 2 1 2 1 1 2 1
Part Number P33952 P10526 P27030 P26501 P10501 P23501 P33217 P33616 P33006 P46507 P46405 P18519 P23504 P46127 P46403 P17550 P27029 P26017 P23538
Part Name Power Unit Hex Hd. Bolt Star Lock Washer Flat Washer Hex Hd. Bolt Lock Nut Male Elbow Inline Filter Street Elbow Ring Terminal Circuit Breaker Screw Nut Battery Cable Battery Terminal Self Tapping Screw Star Washer (small) Split Lock Washer Hex Nut
Material Size/Notes 3/8 – 16 x 3/4
3/8 – 16 x 1
4 Ga. X 30” long
3/8 - 16
Page 53
POWER UNIT ASSEMBLY MONARCH POWER UNIT - GRAVITY DOWN
Page 54
POWER UNIT ASSEMBLY MONARCH POWER UNIT - GRAVITY DOWN
Index No.
Qty.
Part Number Before June 2004
Part Number After July 2004
Part Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 1 1 1 1 1 2 2 4 1 1 2 2 2 4 1 2 1 2 4 1
P33994A P34005 P33616 P33064 Not Required Not Required P10040 P26017 P26506 P10572 P46405 P18519 P23504 P46127 P46403 P11048 P23510 P23538 P10526 P26501 P55337
P33994B P34020 P34046 P34050 P34020 P33771 P10040 P10040 P26506 P10572 P46405 P18519 P23504 P46127 P46403 P11048 P23510 P23538 P10526 P26501 P55337
Monarch Power Unit 90 - Elbow Inline Filter Straight Nipple Elbow Adapter Hex HD Bolt Split Lock Washer Flat Washer Hex HD Bolt Circuit Breaker 10-24x1 Screw 10-24 Lock Nut Battery Cable 4 GA. Battery Terminal Hex HD Bolt Lock Nut Hex Nut Hex HD Bolt Flat Washer Important Instructions Decal
Page 55
POWER UNIT ASSEMBLY SPX DUAL POWER UNIT - GRAVITY DOWN
Page 56
POWER UNIT ASSEMBLY SPX DUAL POWER UNIT - GRAVITY DOWN
Index No.
Qty.
Part Number
Part Name
Material Size
1 2 3 4 5 6 6 7 8 9 9 10 11 11 12 13 14 15 16 17
1 4 4 8 5 4 4 3 3 1 1 1 2 2 2 1 4 2 2 4
P33999 P10526 P27030 P26501 P33217 P33208 P34049 P33216 P33006 P33616 P34046 P33588 AT-501-100-020 AT-501-354-020 P27029 P17518 P26017 P23538 P11048 P33771
Dual Power Unit Bolt Star Washer Flat Washer Male Elbow Ball Valve Ball Valve Tee Street Male Street Elbow Inline Filter Inline Filter Plug Hyd. Line Assembly Hyd. Line Assembly Star Washer Self Tapping Screw Split Lock Washer 3/8 x 1 – ¼ HH Scr. 3/8 – 16 Hex Nut Fitting
SPX DC – 1056 Modified 3/8 – 16 x 3/4
Before 7/04 After 7/04
Before 7/04 After 7/04 Before 7/04 After 7/04 Under Ground Wire
Page 57
POWER UNIT ASSEMBLY MONARCH DUAL POWER UNIT PARTS
COMPLETE POWER UNIT LESS ELBOWS AND FILTER – P34012A THE POWER UNIT’S BLUE WIRE ARE TYPICALLY GROUND WIRES EXCEPT AS NOTED
Page 58
POWER UNIT ASSEMBLY MONARCH DUAL POWER UNIT - GRAVITY DOWN
Page 59
POWER UNIT ASSEMBLY MONARCH DUAL POWER UNIT - GRAVITY DOWN
Index No.
Qty.
Part Number
Part Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 4 4 8 2 2 1 2 1 2 2 4 1 2 1
P34012A P10526 P26017 P26501 P11048 P23538 P34041 P34020 P34046 P10572 P46127 P46403 P55337 P34004 P46649
Dual Power Unit Hex Bolt Split Lock Washer Flat Washer Hex Bolt Hex Nut 90 Elbow 90 Elbow Inline Filter Hex Hd. Bolt Battery Cable 4 GA. Battery Terminal Decal Cap Nut Shrink Tube
Material Size 3/8 – 16 x ¾ 3/8 3/8 3/8 – 16 x 1 1/4 3/8 - 16 Both Male ORB Male ORB – Male JIC 5/16 – 18 x ½ long 1 pc – 35” – 1 pc – 14” Important Instructions 1 pc. – 5” long
Page 60
POWER UNIT ASSEMBLY SPX POWER UNIT - POWER DOWN
Page 61
POWER UNIT ASSEMBLY SPX POWER UNIT - POWER DOWN
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Qty. Part Number 1 P33952 2 P10526 2 P27030 8 P26501 3 P33006 1 P33217 1 P33616 1 P33199 2 P33871 2 P33896 2 P33606 2 P31050 1 P33216 1 P33007 1 AT-501-100-020 2 P46318 2 P46471 1 P46507 1 P17550 2 P11048 2 P23501
Part Name Power Unit Hex HD Bolt Star Lock Washer Flat Washer Street Elbow Male Elbow Pipe Inline Filter Male Street Tee Valve Block Valve & Coil Assembly Male Branch Tee Pipe Plug Stl. Tee Street Male Nipple Hyd. Line Assy Female Connect Terminal Blue Ground Wire Ring Term. Self Tapping Screw Bolt Lock Nut
Material Size 3/8 x ¾ lg. For 3/8 bolt 3/8 inch 3/8 3/8 3/8
3/8 3/8
4 pcs. 8” lg. each
3/8-16 Page 62
POWER UNIT ASSEMBLY MONARCH POWER UNIT - POWER DOWN
Page 63
POWER UNIT ASSEMBLY MONARCH POWER UNIT - POWER DOWN NPT Connections
Index No.
Qty.
Part Number
Part Name
1 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
1 1 1 1 1 1 1 2 2 4 1 1 2 2 2 4 1 2 1 2 1 2 2 2 2 1 1 1 1 1 2 2 2 2 4
P33994B P33199 P33616 P34046 P33064 P34020 P33771 P10040 P26017 P26506 P10572 P46405 P18519 P23504 P46127 P46403 P11048 P23510 P23538 P33006 BA-501-340 P33871 / P34047 P33896 P34002 P34004 P33216 P33007 AT-501-100-020 P46017 P46156 P46318 P46471 P46507 P10526 P28501
Monarch M-3553 Power Unit 90 – Elbow Inline Filter Inline Filter o-ring connections Straight Nipple Elb O-ring Boss 37’ Flare Adapter Hex HD Bolt Split Lock washer Flat Washer Hex HD Bolt Circuit Breaker 10-24x1 Screw 10-24 Lock Nut Battery Cable 4 GA. Battery Terminal Hex HD Bolt Lock Nut Hex Nut Street Elbow Valve Support. Bracket Kit Valve Block Valve & Coil Assy Male Branch Tee Cap Nut Tee Nipple 6” long Hyd. Line Assy. #16 Black Wire (12” long) Butt Conn. Insulated Female Connect Terminal Blue Ground Wire Ring Terminal Hex HD Bolt Flat Washer
Material Size Before June 2004 After July 2004 3/8 NPT – 9/16 –18-37 9/16-18 O-ring-9/16-19-37 9/16-18 SAE-3/8 NPT 5/16 – 18x1 3/8 5/16 5/16-18x1/2 long Not Shown Not Shown Not Shown 1pc 30” – 1pc 20” 3/8-16x1-1/4 5/16-18 3/8-16
Before 6/04 – After 7/04 3/8 NPT 9/16 SAE 37’
Not Shown Not Shown Not Shown 2pcs -16” long Not Shown Not Shown 3/8 – 16x ¾ long 3/8
Page 64
POWER UNIT ASSEMBLY SPX DUAL POWER UNIT - POWER DOWN After 7/04 (SAE 0-ring / JIC fittings)
Page 65
POWER UNIT ASSEMBLY SPX DUAL POWER UNIT - POWER DOWN
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Qty. 1 4 4 8 2 2 2 2 4 4 5 2 2 2 2 4 4 2 1 2 1 1 2 4 2 2 2 3 1 1 2
Part Number Part Name P33999 Dual Power Unit P10526 Hex HD Bolt P27030 Star Washer P26501 Flat Washer P33006 Street Elbow P34041 90 Elbow, Both Male ORB P34046 Inline Filter P34040 Tee, Male ORB Side – Male J Rest P34047 Valve Block P33896 Valve & Coil P34043 Tee, Female J Bott. – Male J Sides P34004 Cap Nut P34010 Tee, All Male J P33007 Nipple AT-501-354-020 Hyd. Line Assy. P46318 Female Connect Terminal P46471 Blue Ground wire P46507 Ring Terminal P17550 Screw AT-501-354-027 Hyd. Line Assy. AT-501-354-015 Hyd. Line Assy. BA-501-336 Valve Support Bracket P34042 Adapter, Female J – Male ORB P26017 Split Lock Washer P23538 3/8 – 16 Hex Nut P11048 3/8 x 1- ¼ HH Screw P34044 Adapter, Male J – Male ORB P34045 90 Elbow, Male ORB – Female J P34015 90 Elbow, Both Male J P34020 90Elbow Male ORB – Male J P33771 Adapter, Male ORB – Female NPT
Material Size 3/8 x 34 long For 3/8 Bolt
4pcs-8” long
Page 66
POWER UNIT ASSEMBLY MONARCH DUAL POWER UNIT - POWER DOWN
Page 67
POWER UNIT ASSEMBLY MONARCH DUAL POWER UNIT - POWER DOWN
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Qty. Part Number 1 P34012A 4 P10526 4 P26017 8 P26501 2 P11048 2 P23538 4 P33006 1 P34020 1 P34046 2 P10572 2 P46127 4 P46403 2 P33007 2 P33771 4 P34047 4 P33896 2 P34045 2 P34010 2 P34043 4 P34004 1 P34050 2 P34044 3 P34042 3 P34051 1 P34053 1 AT-501-354-020 1 AT-501-354-015 1 AT-501-354-018 1 BA-501-383 1 P55337 1 P46471 4 P46318 1 P46649
Part Name Dual Power Unit Hex Bolt Split Lock Washer Flat Washer Hex Bolt Hex Nut Street Elbow 90 elbow, Male ORB – Male JIC Inline Filter Hex HD Bolt Battery Cable 4 GA. Battery Terminal Nipple Adapter, Male ORB – Female NPT Valve Block Valve & Coil Assy. 90 elbow, Male ORB – Female JIC Tee, All Male JIC Tee, Female JIC Bott – Male JIC Cap Nut Str. Nipple, Male ORB – Male ORB Adapter, Male JIC – Male ORB Adapter, Female JIC – Male ORB 90 elbow, Female JIC – Male JIC Cross, All Male JIC Hyd. Line Assy. Hyd. Line Assy. Hyd. Line Assy. Valve Support Bracket Decal Important Instructions 16 GA. Blue Ground Wire Female Disconnect Spade Heat Shrink (black)
Material Size 3/8-16 x 3/4 3/8 3/8 3/8 – 16 x 1-1/4 3/8 - 16
5/16 – 18 x 1/2 1pc 35” – 1pc 14”
Not Shown 4pcs – 16” Not Shown 1pc – 5”
Page 68
HAND PUMP ASSEMBLY GRAVITY - DOWN FOR SPX POWER UNIT BEFORE 4/03
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Qty. 1 2
Part Number P33902 P15540
Part Name Hand Pump with Handle Socket Head Cap Screw
2 2 2 2 1 2 1 1 2 2 2 2 1
P23502 P33101 AT-501-100-015 P33216 AT-501-100-018 P33006 P33199 P33208 P46192 P17518 P10040 P23510 AP-501-267
Lock Nut Adapter Hyd. Line Assy Street Tee Hyd. Line Assy Street Elbow Male Street Tee Ball Valve Holder Self Tapping Screw Bolt Lock Nut Mounting Bracket
Material Size
3/8 NPT(M) – 3/8 NPT(F)
5/16 – 18 x 1 5/16
Page 69
HAND PUMP ASSEMBLY GRAVITY DOWN - FOR MONARCH POWER UNIT 4/03 – 4/07
NPT CONNECTIONS USED 4/03 – 9/04 JIC / SAE 0-RING CONNECTIONS USED 10/04 – 4/07
Index No.
Qty.
Part Number
Part Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1 2 2 2 2 2 1 2 1 1 2 2 2 2 1 1 1 1
P33902 P15540 P23502 P33101 AT-501-100-015 P33216 AT-501-100-018 P33006 P33199 P33208 P46192 P17518 P10040 P23510 AP-501-267 P34005 P34022 P34009
Hand Pump with Handle Socket Head Cap Screw Lock Nut Adapter Hyd. Line Assy Street Tee Hyd. Line Assy Street Elbow Male Street Tee Ball Valve Holder Self Tapping Screw Bolt Lock Nut Mounting Bracket Elbow 90 Elbow Street Adapter
Material Size
AT-501-354-015 (JIC) AT-501-354-018 (JIC) 3/8 NPT(M) – 3/8 NPT(F) P34049 (SAE O – RING)
5/16 – 18 x 1 5/16 3/8 NPT(M) – 9/16-18-37(M) 3/8 NPT(F) – ¼ NPT(F) ¼ NPT(M) – 9/16 SAE 37 (F)
Page 70
HAND PUMP ASSEMBLY POWER DOWN - FOR SPX POWER UNIT BEFORE 4/03
Index No.
Qty.
Part Number
Part Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
1 2 2 1 2 2 2 2 1 2 1 3 2 1 1 2 2
P33902 P15540 P23502 AP-501-267 P10040 P23510 P33101 AT-501-100-015 AT-501-100-035 P33006 AT-501-100-020 P33216 P33208 P33217 P33199 P46192 P17518
Hand Pump with Handle Socket Head Cap Screw Lock Nut Mounting Bracket Bolt Lock Nut Adapter Hyd. Line Assy. Hyd. Line Assy. Street Elbow Hyd. Line Assy. Tee Ball Valve Male Elbow Male Street Tee Tool Holder Self Tapping Screw
Material Size
5/16 – 18 x 1 5/16
3/8 NPT(M) – 9/16-18-37(M)
Page 71
HAND PUMP ASSEMBLY POWER DOWN - FOR MONARCH POWER UNIT 4/03 – 4/07
NPT CONNECTIONS USED 4/03 – 2/05 JIC / SAE 0-RING CONNECTIONS USED 3/05 – 4/07
Index No.
Qty.
Part Number
Part Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 2 2 1 2 2 2 2 1 1 1 3 2 1 1 2 2 1 1 1
P33902 P15540 P23502 AP-501-267 P10040 P23510 P33101 AT-501-100-015 AT-501-100-035 P34023 AT-501-100-020 P33216 P33208 P33217 P33199 P46192 P17518 P34005 P34009 P34022
Hand Pump with Handle Socket Head Cap Screw Lock Nut Mounting Bracket Bolt Lock Nut Adapter Hyd. Line Assy. Hyd. Line Assy. Female Elbow Hyd. Line Assy. Tee Ball Valve Male Elbow Male Street Tool Holder Self Tapping Screw Elbow Street Adapter 90 Elbow
Material Size
5/16 – 18 x 1 5/16 AT-501-354-015 (JIC) AT-501-354-035 (JIC) 9/16 – 18-37(F) – 3/8 NPT (F) AT-501-354-020 (JIC) P34049 (SAE O-RING)
3/8 NPT(M) – 9/16-18-37(M) ¼ NPT(M) – 9/16 SAE 37 (F) 3/8 NPT(F) – ¼ NPT(F)
Page 72
HAND PUMP ASSEMBLY GRAVITY DOWN - FOR MONARCH POWER UNIT AFTER 4-1-07
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Qty. 1 2 2 2 2 2 1 1 1 2 2 2 2 2 1 2 2 2 1
Part Number P33902 P15540 P23502 P34006 AT-501-354-015 P34040 AT-501-354-018 P34005 P4048 P34049 P46192 P17518 P10040 P23510 AP-501-267 P34044 P34051 P34042 P34058
Part Name Hand Pump with Handle Socket Head Cap Screw Lock Nut Adapter Hyd. Line Assy Tee Hyd. Line Assy Elbow Tee Ball Valve Holder Self Tapping Screw Bolt Lock Nut Mounting Bracket Adapter Elbow Str. Adapter Str. Adapter
Material Size
¼ NPT (M) – 9/16-18 JIC (M) (2) JIC (M) – (1) ORB (M) 3/8 NPT(M) – 9/16-18 JIC (M) JIC (M) SIDE/BOT – JIC (F) SIDE
5/16 – 18 x 1 5/16 9/16-18 JIC (M) – SAE ORB (M) 9/16 JIC (M) – 9/16 JIC (F) 9/16 JIC (F) – 9/16 ORB (M) 9/16 JIC (F) – 9/16 JIC (F)
Page 73
HAND PUMP ASSEMBLY POWER DOWN - FOR MONARCH POWER UNIT AFTER 4-1-07
Index No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Qty. 1 2 2 1 2 2 2 2 1 1 1 3 3 1 2 2 2 2 2 2
Part Number P33902 P15540 P23502 AP-501-267 P10040 P23510 P34006 AT-501-354-015 AT-501-354-035 P34051 AT-501-354-020 P34010 P34049 P34005 P34048 P46192 P17518 P34040 P34042 P34044
Part Name Hand Pump with Handle Socket Head Cap Screw Lock Nut Mounting Bracket Bolt Lock Nut Adapter Hyd. Line Assy. Hyd. Line Assy. Elbow Hyd. Line Assy. Tee Ball Valve Elbow Tee Tool Holder Self Tapping Screw Tee Str. Adapter Str. Adapter
Material Size
5/16 – 18 x 1 5/16 ¼ NPT (M) – JIC (M)
JIC (F) – JIC (M) JIC (M) ALL BRANCHES 3/8 NPT (M) – JIC (M) 2 JIC (M) – 1 JIC (F)
2 JIC (M) – 1 ORB (M) JIC (F) – ORB (M) JIC (M) – ORB (M)
Page 74
INSTALLATION OF THE WARNING SIGNS/DECALS STREET SIDE DECALS Warning Signs and Decals will be replaced at any time FREE OF CHARGE
Will receive two of these decals. One goes on each side at bottom of outer mast
Page 75
INSTALLATION OF THE WARNING SINGS/ DECALS CURB SIDE DECALS Warning Signs and Decals will be replaced at any time FREE OF CHARGE
Mount each decal next to the Corresponding toggle switch.
Will receive two of these decals. One goes on outer Mast as marked, the other goes on inner mast next to the switch
Page 76
INSTALLING SAFETY DECALS REAR OF VEHICLE DECALS Warning Signs and Decals will be replaced at any time FREE OF CHARGE
Will receive two of these decals One goes on each side of the outer mast
CAUTION KEEP FEET FROM EDGE OF PLATFORM
Page 77
MODEL AND SERIAL NUMBER TAGS Serial No. is also located in MENU 1 of Maintenance Minder 2速 Serial number tag is located inside power unit box.
10900 KENWOOD ROAD CINCINNATI, OHIO 45242 513-891-6210 WWW.LEYMANLIFT.COM
MODEL
FBG35RM-8042CR
SERIAL NO.
269999
CAPACITY
3500 lbs.
MANUFACTURE DATE
MAY-06
Model number tag is located on the left-hand outer mast.
10900 KENWOOD ROAD CINCINNATI, OHIO 45242 513-891-6210 WWW.LEYMANLIFT.COM
MODEL
FBG35RM-8042CR
CAPACITY
3500 lbs.
MANUFACTURE DATE
MAY-06
PATENTS PENDING
Page 78
ALIGN ARROWS DECALS Install left arrow on Inner Mast.
Install right Arrow on cylinder
Align platform ear in center of cut out of Outer Mast
P55417
Page 79
NOTES _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________
Page 80