Würth Bond and Seal

Page 1

ASSOCIATED PRODUCTS

BOND+SEAL applicator gun 1891 628 0 with wing nozzle 0891 660

applicator gun 1891 010 with yellow nozzle 1890 999

applicator gun 0891 628 6

silicone remover 0893 222 with pro wipe 1899 800 810

goggles 0899 102 111 with dust mask 1899 132

Elastic adhesives and sealants


BOND+SEAL FAST Fast, spreadable PU sealing compound

FAST

BOND + SEAL

BOND+SEAL Elastic and versatile PU adhesive and sealant

• All purpose application • Elastic with high flexibility • Long skin formation time • Can be sanded and painted over • Certificated for use with food (ISEGA certificate) • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, sewage, weak acids and alkaline solutions • Skin formation time at 23°C/50% relative humidity approximately 45-60 minutes • Thermal stability -40°C to 90°C briefly 8 hours at 120°C • Shore A hardness (DIN 53505) approximately 40

Cartridge 310ml Pack quantity 1/12 0890 100 1

• Strong adhesive • Permanently elastic sealing compound • Good stability • Short skin formation time • Can be sanded and painted over quickly • Certificated for use with food (ISEGA certificate) • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, sewage, weak acids and lyes • Skin formation time at 23°C/50% relative humidity approximately 20 minutes • Thermal stability -40°C to 90°C briefly 8 hours at 120°C • Shore A hardness (DIN 53505) approximately 40

White

Cartridge 310ml Pack quantity 1/12 0890 100 710

0890 100 2

White

Grey

0890 100 720

0890 100 3

Grey

Black

0890 100 730

0890 100 4

Black

Brown

Sachet 400ml Pack quantity 12 0890 100 111 White

0890 100 112 Grey

0890 100 113 Black

Sachet 600ml Pack quantity 1/20 0890 100 181 White

0890 100 182 Grey

0890 100 183 Black


BOND+SEAL FAST Fast, spreadable PU sealing compound

FAST

BOND + SEAL

BOND+SEAL Elastic and versatile PU adhesive and sealant

• All purpose application • Elastic with high flexibility • Long skin formation time • Can be sanded and painted over • Certificated for use with food (ISEGA certificate) • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, sewage, weak acids and alkaline solutions • Skin formation time at 23°C/50% relative humidity approximately 45-60 minutes • Thermal stability -40°C to 90°C briefly 8 hours at 120°C • Shore A hardness (DIN 53505) approximately 40

Cartridge 310ml Pack quantity 1/12 0890 100 1

• Strong adhesive • Permanently elastic sealing compound • Good stability • Short skin formation time • Can be sanded and painted over quickly • Certificated for use with food (ISEGA certificate) • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, sewage, weak acids and lyes • Skin formation time at 23°C/50% relative humidity approximately 20 minutes • Thermal stability -40°C to 90°C briefly 8 hours at 120°C • Shore A hardness (DIN 53505) approximately 40

White

Cartridge 310ml Pack quantity 1/12 0890 100 710

0890 100 2

White

Grey

0890 100 720

0890 100 3

Grey

Black

0890 100 730

0890 100 4

Black

Brown

Sachet 400ml Pack quantity 12 0890 100 111 White

0890 100 112 Grey

0890 100 113 Black

Sachet 600ml Pack quantity 1/20 0890 100 181 White

0890 100 182 Grey

0890 100 183 Black


BOND+SEAL DUO Fast curing, elastic 2-component

elastic hybrid structural adhesive

PU adhesive system

DUO

POWER

BOND+SEAL POWER High-capacity, wet on wet,

• High capacity, wet on wet, elastic hybrid structural adhesive • Excellent adhesive range with minimum pre-treatment • Elastic with low flexibility • High initial strength • Can be painted over • UV resistant • High resistance to aging and weather • Non corrosive • Odourless • VOC and solvent free • Isocyanate, PVC and silicone free • Resistant to water and salt water, watery tenside solutions • Skin formation time at 23°C/50% relative humidity approximately 40 minutes • Thermal stability -40°C to 90°C briefly 16 hours at 120°C/ 4 hours at 140°C • Shore A hardness (DIN 53505) approximately 50

Cartridge 310ml Pack quantity 1/12 0890 235 1 White

0890 235 2 Grey

0890 235 3 Black

• Two-component reaction resin • Elastic at high strength • Outstanding stability • Functional strength achieved after a short time • Sanded and painted over quickly • Good weather resistance • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, weak acids and lyes • Skin formation time at 20°C approximately 15-20minutes • Thermal stability -40°C to 80°C • Shore A hardness (DIN 53505) approximately 65

Cartridge 380ml Pack quantity 6 0891 234 Light Beige


BOND+SEAL DUO Fast curing, elastic 2-component

elastic hybrid structural adhesive

PU adhesive system

DUO

POWER

BOND+SEAL POWER High-capacity, wet on wet,

• High capacity, wet on wet, elastic hybrid structural adhesive • Excellent adhesive range with minimum pre-treatment • Elastic with low flexibility • High initial strength • Can be painted over • UV resistant • High resistance to aging and weather • Non corrosive • Odourless • VOC and solvent free • Isocyanate, PVC and silicone free • Resistant to water and salt water, watery tenside solutions • Skin formation time at 23°C/50% relative humidity approximately 40 minutes • Thermal stability -40°C to 90°C briefly 16 hours at 120°C/ 4 hours at 140°C • Shore A hardness (DIN 53505) approximately 50

Cartridge 310ml Pack quantity 1/12 0890 235 1 White

0890 235 2 Grey

0890 235 3 Black

• Two-component reaction resin • Elastic at high strength • Outstanding stability • Functional strength achieved after a short time • Sanded and painted over quickly • Good weather resistance • Non corrosive • Odourless • Silicone free • Resistant to water, seawater and lime water, weak acids and lyes • Skin formation time at 20°C approximately 15-20minutes • Thermal stability -40°C to 80°C • Shore A hardness (DIN 53505) approximately 65

Cartridge 380ml Pack quantity 6 0891 234 Light Beige


BOND+SEAL ALL IN ONE MS-polymer based seam sealant for spraying and spreading, restoring the original structure

BOND+SEAL ACTIVATING CLEANER

For cleaning and activation of nonporous surfaces, such as metals, plastics, glazed ceramics and painted surfaces • Drying time: at least 10 minutes (23°C/50% relative humidity) • Not for smoothing or removing of adhesives or sealing compounds

ALL IN ONE

Contents 400ml Pack quantity 1/12 0890 100 60

BOND+SEAL REMOVER • Excellent reproduction of a broad range of original manufactures structures • One product for two applications, spraying and spreaading • Permanently elastic after hardening • Can be painted over both before skin formation (wet-on-wet) and up to a maximum of five days afterwards • UV resistant • Solvent free • Broad adhesion range • Non corrosive • Safety product • Isocyanate, PVC and silicone free • Resistant to fresh water and salt water, aqueous tenside solutions • Skin formation time at 23°C/50% relative humidity approximately 20 minutes • Thermal stability -40°C to 80°C briefly 16 hours at 120°C/ 4 hours at 140°C • Shore A hardness (DIN 53505) approximately 50

Cartridge 310ml Pack quantity 12 0890 236 110 White

0890 236 120 Grey

0890 236 130

For removal of PU or hybrid adhesives and sealing compounds from tools and non-porous surfaces, before they are fully cured Contents 400ml Pack quantity 1/12 0890 100 63

BOND+SEAL PRIMER FOR PLASTIC/WOOD/STONE

For treatment of plastics (PVC, ABS, GFK), wood and other porous substrates, such as stone and concrete • Drying time: at least 30 minutes (23°C/50% relative humidity) • Not for PE, PP, PTFE, PMMA and PC

Contents 250ml Pack quantity 1/6 0890 100 62

Black

BOND+SEAL PRIMER FOR METAL

For treatment of metallic substrates such as iron, steel, stainless steel, galvanised steel, aluminum, anodised aluminum, copper, brass, zinc • Drying time: at least 30 minutes (23°C/50% relative humidity) • Not for corrosion protection

Contents 250ml Pack quantity 1/6 0890 100 61


BOND+SEAL ALL IN ONE MS-polymer based seam sealant for spraying and spreading, restoring the original structure

BOND+SEAL ACTIVATING CLEANER

For cleaning and activation of nonporous surfaces, such as metals, plastics, glazed ceramics and painted surfaces • Drying time: at least 10 minutes (23°C/50% relative humidity) • Not for smoothing or removing of adhesives or sealing compounds

ALL IN ONE

Contents 400ml Pack quantity 1/12 0890 100 60

BOND+SEAL REMOVER • Excellent reproduction of a broad range of original manufactures structures • One product for two applications, spraying and spreaading • Permanently elastic after hardening • Can be painted over both before skin formation (wet-on-wet) and up to a maximum of five days afterwards • UV resistant • Solvent free • Broad adhesion range • Non corrosive • Safety product • Isocyanate, PVC and silicone free • Resistant to fresh water and salt water, aqueous tenside solutions • Skin formation time at 23°C/50% relative humidity approximately 20 minutes • Thermal stability -40°C to 80°C briefly 16 hours at 120°C/ 4 hours at 140°C • Shore A hardness (DIN 53505) approximately 50

Cartridge 310ml Pack quantity 12 0890 236 110 White

0890 236 120 Grey

0890 236 130

For removal of PU or hybrid adhesives and sealing compounds from tools and non-porous surfaces, before they are fully cured Contents 400ml Pack quantity 1/12 0890 100 63

BOND+SEAL PRIMER FOR PLASTIC/WOOD/STONE

For treatment of plastics (PVC, ABS, GFK), wood and other porous substrates, such as stone and concrete • Drying time: at least 30 minutes (23°C/50% relative humidity) • Not for PE, PP, PTFE, PMMA and PC

Contents 250ml Pack quantity 1/6 0890 100 62

Black

BOND+SEAL PRIMER FOR METAL

For treatment of metallic substrates such as iron, steel, stainless steel, galvanised steel, aluminum, anodised aluminum, copper, brass, zinc • Drying time: at least 30 minutes (23°C/50% relative humidity) • Not for corrosion protection

Contents 250ml Pack quantity 1/6 0890 100 61


Surface/material

Primer treatment steps

Aluminium (AlMg3, AlMgSi1)

B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner

Aluminium anodised

Contact Würth

Steel (St 37etc.)

We operate a team of regional sales consultants covering from the north of Scotland down to the tip of Cornwall. All of our consultants are fully trained to give you the best advice and service in your field. We also have product specialists who can help with queries on any associated products.

Stainless steel Steel, galvanised or hot galvanised 2-comp. top coats (PU, epoxy), 2-comp. water based primers and enamels, KTL, primers (EP/2-comp.) Powder coated surfaces

To find out more about the product range, please either contact your local sales consultant or Würth’s customer service centre on 08705 987 841 and they will be happy to answer any questions directly.

GFK (unsaturated polyester), gelcoat side or SMC GFK (unsaturated polyester), lay up side

ABS Rigid PVC Glass (mineral) Glass ceramics Wood and wood products (particle boards) untreated Natural stone Concrete, mineral mortar and plaster Textiles, fleece

B+S Activating Cleaner B+S Activating Cleaner 1. Sand with 0674 000 80 emery cloth sheet 2. B+S Activating Cleaner 3. B+S Primer for P/W/S 1. Sand with sanding fleece 2. B+S Activating Cleaner 3. B+S Primer for P/W/S 1. Sand with sanding fleece 2. B+S Activating Cleaner 3. B+S Primer for P/W/S B+S Activating Cleaner B+S Activating Cleaner 1. Remove dust 2. B+S Primer for P/W/S 1. Remove dust 2. B+S Primer for P/W/S 1. Remove dust 2. B+S Primer for P/W/S B+S Primer for P/W/S

First, select the m

Important requirement Elastic with high ductility

Application

Würth UK Limited 1 Centurion Way Erith • Kent DA18 4AE Tel. 08705 987 841 Fax. 08705 987 842 www.wurth.co.uk © Würth UK Ltd. All rights reserved in all media.

The information expressed is intended as a recommendation only, based on our tests and experience. However, we cannot accept any responsibility for results in individual cases because of the wide variety of applications as well as storage and processing conditions beyond our control. This also applies when making use of our technical and commercial customer service which is supplied free of charge and without obligation. We always recommend that you carry out individual tests. We guarantee the consistent quality of our products. Subject to technical changes and developments. Würth UK Limited cannot accept responsibility for any errors or omissions or for any losses that may arise as a result.

WUK/ - pjc - 10/07 • 1999 09

No part of this catalogue may be reproduced in any form, copied or stored electronically, whole or in part without prior written permission. Every effort has been made to verify all information. Products may vary in appearance from those pictured.

Elastic with low ductility

Seam sealing / joints (e.g. automobile body overlap seams, container sealing, stepped welds, housing seals, expansions joints, sealing of gaps) Visible joints (e.g. connecting joints) Large area bonding (e.g. bumpers, floor plates, checker plates and stairs on supports, corner and edge protector plates) Seam / spot bonding (e.g. sheet metal overlaps, angle profiles, truck side walls, brackets, frame bonding, installing signs) Bond of tough profiles

UV an weath resista

Bonding of tuning components (e.g. spoilers) Observe manufacturers instructions

Key

Bond + Seal

Bond + Seal Fast

Bond + Sea


APPLICATION TABLE s ssary, first sand lightly with sanding fleece

ssary, first sand lightly with sanding fleece. of steel components in danger of corrosion: p. PU or epoxy corrosion protection required

ssary, first sand lightly with sanding fleece. the wide variety of enamels, ormation is for reference only, nary testing required nary testing recommended for applications gh forces or in moist ambient conditions ssary, first sand lightly nding fleece

g may be omitted in case of components to light loads. g may be omitted in case of components to light loads. surface must be protected t UV radiation (opaque covering)

Note: The adjacent information always relates to the surface of the component (e.g. steel coated with 2-component epoxy enamel: see 2-comp. top coats). Prior to starting primer treatment, all components must be clean, dry, free of dust, grease and oil. Unstable or loose layers must be removed first. After that, spray the surface with a thin coat of B+S Activating Cleaner and wipe off with a clean cloth or absorbent paper, or spray B+S Activating Cleaner onto a cloth and wipe the surfaces to be joined. Always wipe in the same direction. Afterwards, apply a thin coat of B+S Primer for Metal or Primer for Plastic/Wood/Stone evenly with a brush. Important: Prior to the next step, the previously applied layer must have set and dried completely. OBSERVE DRYING TIMES!

e discolouration in case of stone (marble)

APPLICATOR GUNS

Pneumatic 1891 628 0 - 310ml cartridge and sachet 1891 010 - up to 310ml cartridge 1891 831 0 - up to 360ml sachet 1891 860 0 - up to 600ml sachet COMBIFIX 1891 628 6 - 310ml cartridge only

Manual 0891 001 - up to 310ml cartridge 1892 999 - up to 380ml cartridge 1891 310 - up to 360ml sachet 1892 160 0 - up to 600ml sachet Twin cartridge gun 0891 601 23 - for 0893 234 cartridge

NOZZLES

For cartridges with fine thread 0890 100 099 - Transparent 0890 100 299 - Grey 0890 100 399 - Black Wing Nozzles 0891 660 Yellow Nozzle 1890 999

SAFETY

nary testing required. e cases, meshing of adhesive e textile is sufficient

GUIDANCE rtant requirement of your application, then find the suitable product in the application column Contact with food (certificate)

Over-painting with waiting time

Over-painting immediately

High dynamic / Quick final mechanical strength load capability

Automotive latex gloves 1899 001/002 Automotive powder free latex gloves 0899 463 100/101/102/103 Dust mask FF2 1899 132 Goggles 0899 100 0 0899 102 101/111 Pro paint overall 1899 020 001/002/003/004 Barrier hand foam 0890 304 Hand cleaner 0893 900 0 Industrial hand cleaner wipes 0890 900

MISCELLANEOUS

Sealer brush 0693 30 Pro wipes 1899 800 810 Silicone remover 0893 222/600/5 Cartridge knife 0715 66 09 Scraper and knife set 0715 66 40

Bond + Seal Duo

Bond + Seal All In One


APPLICATION TABLE s ssary, first sand lightly with sanding fleece

ssary, first sand lightly with sanding fleece. of steel components in danger of corrosion: p. PU or epoxy corrosion protection required

ssary, first sand lightly with sanding fleece. the wide variety of enamels, ormation is for reference only, nary testing required nary testing recommended for applications gh forces or in moist ambient conditions ssary, first sand lightly nding fleece

g may be omitted in case of components to light loads. g may be omitted in case of components to light loads. surface must be protected t UV radiation (opaque covering)

Note: The adjacent information always relates to the surface of the component (e.g. steel coated with 2-component epoxy enamel: see 2-comp. top coats). Prior to starting primer treatment, all components must be clean, dry, free of dust, grease and oil. Unstable or loose layers must be removed first. After that, spray the surface with a thin coat of B+S Activating Cleaner and wipe off with a clean cloth or absorbent paper, or spray B+S Activating Cleaner onto a cloth and wipe the surfaces to be joined. Always wipe in the same direction. Afterwards, apply a thin coat of B+S Primer for Metal or Primer for Plastic/Wood/Stone evenly with a brush. Important: Prior to the next step, the previously applied layer must have set and dried completely. OBSERVE DRYING TIMES!

e discolouration in case of stone (marble)

APPLICATOR GUNS

Pneumatic 1891 628 0 - 310ml cartridge and sachet 1891 010 - up to 310ml cartridge 1891 831 0 - up to 360ml sachet 1891 860 0 - up to 600ml sachet COMBIFIX 1891 628 6 - 310ml cartridge only

Manual 0891 001 - up to 310ml cartridge 1892 999 - up to 380ml cartridge 1891 310 - up to 360ml sachet 1892 160 0 - up to 600ml sachet Twin cartridge gun 0891 601 23 - for 0893 234 cartridge

NOZZLES

For cartridges with fine thread 0890 100 099 - Transparent 0890 100 299 - Grey 0890 100 399 - Black Wing Nozzles 0891 660 Yellow Nozzle 1890 999

SAFETY

nary testing required. e cases, meshing of adhesive e textile is sufficient

GUIDANCE rtant requirement of your application, then find the suitable product in the application column Contact with food (certificate)

Over-painting with waiting time

Over-painting immediately

High dynamic / Quick final mechanical strength load capability

Automotive latex gloves 1899 001/002 Automotive powder free latex gloves 0899 463 100/101/102/103 Dust mask FF2 1899 132 Goggles 0899 100 0 0899 102 101/111 Pro paint overall 1899 020 001/002/003/004 Barrier hand foam 0890 304 Hand cleaner 0893 900 0 Industrial hand cleaner wipes 0890 900

MISCELLANEOUS

Sealer brush 0693 30 Pro wipes 1899 800 810 Silicone remover 0893 222/600/5 Cartridge knife 0715 66 09 Scraper and knife set 0715 66 40

Bond + Seal Duo

Bond + Seal All In One


ASSOCIATED PRODUCTS

BOND+SEAL applicator gun 1891 628 0 with wing nozzle 0891 660

applicator gun 1891 010 with yellow nozzle 1890 999

applicator gun 0891 628 6

silicone remover 0893 222 with pro wipe 1899 800 810

goggles 0899 102 111 with dust mask 1899 132

Elastic adhesives and sealants


Surface/material

Primer treatment steps

Aluminium (AlMg3, AlMgSi1)

B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner and, if necessary, B+S Primer for Metal B+S Activating Cleaner

Aluminium anodised

Contact Würth

Steel (St 37etc.)

We operate a team of regional sales consultants covering from the north of Scotland down to the tip of Cornwall. All of our consultants are fully trained to give you the best advice and service in your field. We also have product specialists who can help with queries on any associated products.

Stainless steel Steel, galvanised or hot galvanised 2-comp. top coats (PU, epoxy), 2-comp. water based primers and enamels, KTL, primers (EP/2-comp.) Powder coated surfaces

To find out more about the product range, please either contact your local sales consultant or Würth’s customer service centre on 08705 987 841 and they will be happy to answer any questions directly.

GFK (unsaturated polyester), gelcoat side or SMC GFK (unsaturated polyester), lay up side

ABS Rigid PVC Glass (mineral) Glass ceramics Wood and wood products (particle boards) untreated Natural stone Concrete, mineral mortar and plaster Textiles, fleece

B+S Activating Cleaner B+S Activating Cleaner 1. Sand with 0674 000 80 emery cloth sheet 2. B+S Activating Cleaner 3. B+S Primer for P/W/S 1. Sand with sanding fleece 2. B+S Activating Cleaner 3. B+S Primer for P/W/S 1. Sand with sanding fleece 2. B+S Activating Cleaner 3. B+S Primer for P/W/S B+S Activating Cleaner B+S Activating Cleaner 1. Remove dust 2. B+S Primer for P/W/S 1. Remove dust 2. B+S Primer for P/W/S 1. Remove dust 2. B+S Primer for P/W/S B+S Primer for P/W/S

First, select the m

Important requirement Elastic with high ductility

Application

Würth UK Limited 1 Centurion Way Erith • Kent DA18 4AE Tel. 08705 987 841 Fax. 08705 987 842 www.wurth.co.uk © Würth UK Ltd. All rights reserved in all media.

The information expressed is intended as a recommendation only, based on our tests and experience. However, we cannot accept any responsibility for results in individual cases because of the wide variety of applications as well as storage and processing conditions beyond our control. This also applies when making use of our technical and commercial customer service which is supplied free of charge and without obligation. We always recommend that you carry out individual tests. We guarantee the consistent quality of our products. Subject to technical changes and developments. Würth UK Limited cannot accept responsibility for any errors or omissions or for any losses that may arise as a result.

WUK/ - pjc - 10/07 • 1999 09

No part of this catalogue may be reproduced in any form, copied or stored electronically, whole or in part without prior written permission. Every effort has been made to verify all information. Products may vary in appearance from those pictured.

Elastic with low ductility

Seam sealing / joints (e.g. automobile body overlap seams, container sealing, stepped welds, housing seals, expansions joints, sealing of gaps) Visible joints (e.g. connecting joints) Large area bonding (e.g. bumpers, floor plates, checker plates and stairs on supports, corner and edge protector plates) Seam / spot bonding (e.g. sheet metal overlaps, angle profiles, truck side walls, brackets, frame bonding, installing signs) Bond of tough profiles

UV an weath resista

Bonding of tuning components (e.g. spoilers) Observe manufacturers instructions

Key

Bond + Seal

Bond + Seal Fast

Bond + Sea


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.