26/11/2008
HSS Twist Drills • • • • •
DIN 338. Base material: high grade, high speed steel. Ø 0.5 to 19.5 mm. Length: 22 to 205 mm. Suitable for wood, plastic/composites, steel, cast steel (alloy & non alloy), grey iron, malleable cast iron, nodular iron, sintered materials and graphite.
11:59
Page 53
Twist Stubb Drills HSS
• • • •
Short Reach. Ø 3.0 to 10.0 mm. Length: 46 to 89 mm. Special grinding facility that helps the drill to penetrate. • No centre punching required. • Right hand cutting. • Suitable for drilling thin metals, rivet holes, etc.
Art. Prefix: 624...
Twist Drills HSS • • • • •
DIN 338. Base material: high speed steel. Ø 1.0 to 20 mm. Length: 34 to 205 mm. Suitable for wood, plastic/composites, mild and cast steel (alloy & non-alloy), grey cast iron, tempered castings, sintered materials, graphite and nodulariron.
Art. Prefix: 625...
Art. Prefix: 635...
Long Reach. DIN 340. Base material: high speed steel. Ø 2.5 to 13 mm. Length: 95 to 205 mm. Suitable for wood, plastic / composites, mild and cast steel (alloy & non-alloy), grey cast iron, tempered castings, sintered materials, graphite and nodular iron.
Art. Prefix: 629...
• • • • • • • • • •
For Stainless Steel. DIN 338. Ø 2.5 to 13.0 mm. Length: 57 to 151 mm. Point angle: 130°. Side chip angle: 35°. Straight Cylindrical shank. Reduced shank to 12.7mm (from 13mm dia.) Right hand cutting. Use suitable cooling agent: Cutting Oil Art. No: 893.050.004. • Suitable for stainless steel, (corrosion, acid & heat resistant austenitic steel), titanium & titanium alloy. • Limited suitability for special alloys, such as Hastelloy, Inconel, Nimonic, etc.
Titanium-Nitride Twist Drills • • • • • • • •
DIN 338. Ø 2.0 to 12.0 mm. Length: 49 to 151 mm. Titanium-Nitride coating, increasing tool life by up to 10 times. Point angle: 118°. Straight cylindrical shank. Right hand cutting. Suitable for steel & cast steel (alloy & nonalloy), grey iron, malleable cast iron, nodular iron, sintered powder iron, argentan & graphite.
Twist Drills HSS • • • • • •
Cobalt Twist Drill
Art. Prefix: 622...
Extend the life of your drill bits using our cutting oils. See pages 9-10.
Art. Prefix: 626...
Double Ended Twist Drills HSS • • • • • • • • • • •
DIN 1897. Base material: high speed steel. Ø 2.5 to 5.1 mm. Length: 43 to 62 mm. Straight cylindrical shank. Extra short design. Economical design. Right hand cutting. No centre punching required. For drilling rivet holes. Suitable for drilling thin section or sheet metals.
Art. Prefix: 636...
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
53
DRILLING
S040 210 x 195 customer catalogue.qxp
S040 210 x 195 customer catalogue.qxp
26/11/2008
Twist Drills with Taper Shank
DRILLING
• • • • • • •
HSS DIN 345. Ø 12.0 to 22 mm. Length: 182 to 248 mm. Ground taper. Acute angle of 118°. Right hand. Powerful, sturdy standard drill with morse taper shank for use with column type drilling machine. • Suitable for drilling of steel and cast steel (alloy for non-alloy), grey iron, malleable cast iron, nodular iron, sintered-powder metal, argentan and graphite.
12:01
Page 54
Twist Drill HSS Assortment
• DIN 338. • Base material: high speed steel. • 20 sizes, Ø 1.0 to 10.5 mm at 0.5 mm intervals. • Contents 155 pieces. • Point angle: 118°. • Straight cylindrical shank. • Reduced shank to 12. 7mm (from Ø 13 mm). • Right hand cutting. • Complete with carry case. • Suitable for wood, plastic /composites, mild and cast steel (alloy & non-alloy), grey cast iron, tempered castings, sintered materials, graphite, and nodular iron.
Art. Prefix: 628...
HSS Twist Drill Set
• Long life high quality drill bits. • Base materials: high grade high speed steel. • Ø 1.0 to 10.0 mm / 0.5 mm intervals. • Contents: 19 pieces. • Self centring. • Point angle: 130°. • Straight cylindrical shank. • Right hand cutting. • Robust steel box. • Suitable for wood, plastic/composites, steel cast steel (alloy & non alloy), grey iron, malleable cast iron, nodular iron, sintered materials and graphite. Art. No. 624.000.001
Art. No. 964.625.020
Twist Drill HSS Set
• DIN 338. • Base material: high speed steel. • Ø 1.0 - 10.0 / 0.5 mm intervals. • Contents: 19 pieces. • Point angle: 118°. • Straight cylindrical shank. • Right hand cutting • Easy to carry impact resistant case with a transparent top. • Suitable for wood, plastic /composites, mild and cast steel (alloy & non-alloy), grey cast iron, tempered castings, sintered materials, graphite, and nodular iron. Art. No. 625.01
54
Twist Drill HSS Sets
• DIN 338. • Base material: high speed steel. • Point angle: 118°. • Straight cylindrical shank. • Right hand cutting. • Robust steel box. • Suitable for wood, plastic /composites, mild and cast steel (alloy & non-alloy), grey cast iron, tempered castings, sintered materials, graphite, and nodular iron.
Contents: from Ø 1.0 - 10.0 mm / 0.5 mm intervals = 19 twist drills from Ø 1.0 - 13.0 mm / 0.5 mm intervals = 25 twist drills Empty Steel Box Contents: for 19 twist drills Ø. 1.0 - 10.0 mm / 0.5 mm intervals for 25 twist drills Ø 1.0 - 13.0 mm / 0.5mm intervals
3D Bit Set
Art. No. 634.4 634.6 Art. No. 633.4 633.6
• Hardened alloy steel, can be sharpened with a file or grindstone. • Ø 7 to 25 mm. • Contents: 8 pieces. • Complete with plastic case. • Drills curved holes, channels, grooves and recesses. • Mills and countersinks. • Twice as fast as conventional drill bits.
Art. No. 6501.1
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
26/11/2008
Morse Taper Adaptors
• DIN 2185. • Fully hardened. • Smoothed. • For reduction of the Morse taper. • Size: 3a. • Length: 112 mm. Morse taper external = machine tool feed. Morse taper internal = drill input. Example: Machine tool feed MT3 desired drill dia. 16mm (MT2) = required adaptor 628.500.057
12:02
Page 55
HSS Broaching Cutters • • • • • • •
Cutting Ø 12.0 to 30.0 mm. Improved cutting geometry. One size pilot pin fits all cutters. Interchangeable with other makes. For cutting holes in steel beams. Must be used with lubrication cutting oil. For use with electro magnetic drilling machines.
Counter Sink Cutters Art. No. 628.500.057
P/Qty 1
• Ø 40.0 mm. • Up to bolt size: M20. • For use with electromagnetic machine.
Socket Inserts for Drill Holders • • • •
DIN 238. Machine / holder morse taper: MT2. Length: 112 mm. For re-toolling of column-type drilling. machines with Morse Taper on quick change chuck with inside cone (DIN-cone B 16) for cylindrical drills.
Lip & Spur Drill Bits
Description Cone B16
Size mm 1.5 - 13
Vanadium Chrome coated. Drilling Ø 3.0 to 12.0 mm. Length: 61 to 150 mm. Single centre point and two cutting spurs. Suitable for natural timbers and man made boards.
P/Qty 1
Quick Action Metal Chuck (2 Sleeves) Art. No. 692.316.130
Auger Twist Drills
• Drilling Ø 6.0 to 26.0 mm. • Length: 235 to 460 mm. • Spiral pulls bit into wood allowing the single spur to slice ahead of the cutting edge. • Hexagonal shank. • Suitable for drilling precision holes in hard wood and softwood.
Art. Prefix: 650.6...
Art. Prefix: 6321.40
• • • • • Art. No. 628.500.117
• HM Reinforced • High carbon content prolongs life of drill bit. • Drilling Ø 5.0 to 10.0 mm. • Length: 85 to 130 mm. • Suitable for hardwoods, MDF boards and synthetic coated chipboards.
Art. Prefix: 650.40... Art. Prefix: 6321...
From MT to Ext. Int. 3 2
Lip & Spur Drill Bits
Speedbor Bit • • • • •
Sizes 8 to 38 mm. Length: 157 and 171 mm. 150 and 300 mm extensions available. Superior performance to traditional flat bits. Centreless ground/extruded shanks align the point and the shank to ensure concentricity. • ¼” hexagonal shank reduces bit slippage in the drill chuck. • Suitable for hardwoods and softwoods.
Art. Prefix: 650.4... Art. Prefix: 650.6... Assortment Art. No. 964.650.64
www.winzerwurth.co.uk CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
55
DRILLING
S040 210 x 195 customer catalogue.qxp
S040 210 x 195 customer catalogue.qxp
Wood Twist Drill
Chrome-vanadium coated. Drilling Ø 3.0 to 8.0 mm. Length: 75 to 115 mm. Centre point and two cutting edges gives cleaner hole. • ¼” Hexagon shaft fits into a universal bit holder for quick changes. • Suitable for hardwoods and chipboard.
DRILLING
• • • •
26/11/2008
12:03
Page 56
Countersink Attachment • • • • • •
Attaches onto twist drill. Fits drill bits Ø 3.0 to 10.0 mm. Length: 25 mm. Countersink Ø 16 mm. Countersink or reverse as a depth stop. Easy and quick one step operation.
Forstner Drill Bits
• High carbon content prolongs life of drill bit. • Bit Ø 16.0 to 40.0 mm. • Length: 90 mm. • Centre point creates stability, base and circumference cutters then cut a precise, clean hole.
Art. Prefix: 650.7...
Art. Prefix: 650.9...
Art. Prefix: 650.001...
Countersink Bit
Hinge Bit • • • • • •
Tungsten carbide. Bore Ø 35 mm. Shank Ø 10 mm. Length: 25 mm. Right hand boring. Hexagonal shaft. Blades can be removed for easy sharpening. • Suitable for kitchen / cabinet door hinge cups 35 mm.
• • • • •
Bit Ø 10.0 to 16.0 mm. Length: 45 mm. ¼” Hexagonal shaft fits universal bit holder. Quick and easy to use. Ideal for site work.
Machine Centre Bit • • • • •
Material: Tungsten carbide. Bore Ø 35 mm. Length: 90 mm. Centre point, 2 lips and 2 spurs. Suitable for hardwood, softwood and chipboard / MDF.
Art. Prefix: 650.171...
Machine Countersink Bit Art. No. 650.035
Fill the holes with Würth products. Filler, plugs, screws, resins. 56
• • • •
Bit Ø 10.0 to 13.0 mm. Length: 90 mm. Countersink Ø 8 mm. Ideally suited for bench type machines.
Art. Prefix: 650.135
Art. Prefix: 650.171...
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Countersink Bits 90°
26/11/2008
• Type C (round shaft ). • DIN 335. • Cubical boron nitride (CBM deep ground), HSS. • Triple cutting edges. • Deburrs and countersinks in one operation.
12:04
Page 57
Green ring HSS • • • •
Countersink Ø from 8.3 to 25.5 mm Shank Ø from 6 to 10 mm. Length: 50 to 67 mm. Suitable for alloy and high alloy steel as well as stainless and acid resistant steel.
Blue ring HSS • • • •
Countersink Ø from 8.3 to 31 mm. Shank Ø from 6 to 12 mm. Length: 50 to 71 mm. Suitable for normal steel.
Countersink and Deburring Bit HSS-E
(Snail cutter) • 90° with cylindrical hole. • CBN (cubical boron nitride), deep ground. • Head Ø from 10 to 28 mm. • Length: 45 to 85 mm. • Shank Ø from 6 to 12 mm. • For deburring of 90° countersunk holes. • Suitable for most materials.
DRILLING
S040 210 x 195 customer catalogue.qxp
Art. Prefix: 694.019...
Titanium-Nitride HSS Art. Prefix: 694.017...
Yellow ring HSS • • • •
• • • • •
Countersink Ø from 8.3 to 20 mm. Shank Ø from 6 to 10 mm. Length: 50 to 63 mm. Extended tool life by up to four fold. Greater increase of cutting and feed speeds.
Countersink range mm 2 to 5 5 to 10 10 to 15 15 to 20
Countersink and Deburring Bit HSS-E Assortment
Countersink Ø from 6.3 to 20 mm. Shank Ø from 5 to 10 mm. Length: 45 to 63 mm. Suitable for aluminium, aluminium alloys, thermo-plasts and duroplasts.
(Snail cutter) • Complete with metal case. • Set sizes: 1 of; 2-5, 5-10, 10-15, and 15-20 mm.
Art. Prefix: 694.020...
Countersink Bits Art. Prefix: 694.018...
We supply a wide range of dust masks, eye and ear protection, etc. See pages 213-219
Art. No. 694.021.02 694.021.05 694.021.10 694.021.15
• Titanium-nitride HSS Assortment. • Complete with metal case. • Set sizes; 1 of; 6.3, 8.3, 10.4, 12.4, 16.5, 20.5 mm.
Art. No. 694.020.01
Art. No. 694.021.01
Call today and arrange to see your local sales consultant.
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
57
S040 210 x 195 customer catalogue.qxp
26/11/2008
DRILLING
Countersink Bit HSS 90°
With 3 cutting edges. • DIN 335C. • Countersink Ø from 6.3 to 20.5 mm. • Length: 31 to 41 mm. • 6.3mm hexagonal shaft fits universal bit holder. • Possible quick change of countersinking. • Especially suitable for drill / drivers or manual deburring tools. • Suitable for countersinking, chamfering and deburring of steel, non-ferrous meals, wood and plastics.
12:06
Page 58
Masonry Drill Bit • • • •
Bore Ø from 3 to 18 mm. Length: 70 to 150 mm. Exceptionally long tool life. Faster extraction of drilling debris through profile design. • Optimum drilling performance due to excellent transfer of force and torsional loadbearing capacity through design of body and helix. • Suitable for granite, concrete, masonry.
Art. Prefix: 637... Art. Prefix: 694.026...
SDS-Plus 4 Hammer Drill
Countersink Bit HSS 90° Assortment
• Complete with metal case. • Set sizes: 1 of; 6.3, 8.3, 10.4, 12.4,16.5, 20.5 mm Ø.
Art. No. 694.026.01
Multipurpose HM Drill
(wood/masonry) • Bore Ø from 4 to 10 mm. • Length: 85 to 250 mm. • Suitable for ceramics, marble, glass, eternit, floor tiles, bricks, aerated concrete, lightweight building materials and plastics. • Not for use on hammer/impact mode.
Art. Prefix: 641...
58
• Bore Ø from 4 to 16 mm. • Length: 110 to 260 mm. • New tip geometry made of optimised long life tungsten carbide. • Up to 50% longer life. • Faster drilling, up to 25% faster than conventional hammer drills.
Chucks Gear Ring Drill Chuck
Art. Prefix: 692.2...
Quick Action Metal Chuck (2 Sleeves)
Art. Prefix: 692.3...
Quick Action Chuck (2 Sleeves)
Art. Prefix: 692.8...
Mini Chuck Art. Prefix: 713...
Art. Prefix: 648... 7 Part Set Art. No. 648.401
Drill Chuck Key
SDS-Plus 2 Hammer Drill • Bore Ø from 18 to 25 mm. • Length: 200 to 450 mm.
Art. Prefix: 692.1...
SDS to Drill Chuck Adaptor Art. Prefix: 648...
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Art. Prefix: 692...
26/11/2008
Sheet Metal Drill Cone Cutter
• HSS or HSS Titanium-nitride CBN (cubical boron nitride) deep ground. • Length: 61 to 73 mm. • Stepless drilling and opening holes with in the Ø range of 5 - 30 mm. • Suitable for the drilling of thin sheet metal.
12:07
Page 59
Dentist Drills
• Tungsten carbide for long service life. • Suitable for plastics, aluminium, brass, copper, steel, ceramic and glass fibre.
Ball
• Length 38 mm. • Head length: 2.7 mm. • Head Ø 3 mm., Shank Ø 3 mm.
Carbide Burrs
• DIN 8032/8035. • Shank Ø 6 mm. • Universal tooth pattern suitable for: Stainless steel, high grade steel, cast iron, weld seams, hard plastics. • Carbide cutting edge provides a longer service life than HSS bits.
Cylinder (without end cut)
• Length 50 to 70 mm. • Head: Length 16 to 25 mm, Ø 6 to 13 mm. Art. No. 616.330.303
Cylinder (without end cut) Art. Prefix: 694....
Stepped Drill
• HSS or HSS Titanium-nitride. • CBN (cubical boron nitride) deep ground. • Drill Ø 4 to 39 mm. • Length: 65 to 109 mm. • centring, spotdrill, opening & deburring in one go. • Suitable for the drilling of thin sheet metal up to 4 mm.
Art. Prefix: 694....
• Length 38 mm. • Head length: 14 mm. • Head Ø 3 mm., Shank Ø 3 mm.
Art.Prefix: 616...
Cylinder (with end cut)
• Length 50 to 64 mm. • Head length: 16 to 19 mm, Ø 6 to 10 mm.
Art. No. 616.130.314
Art.Prefix: 616...
Tree
• Length 38 mm. • Head length: 12 mm. • Head Ø 3 mm., Shank Ø 3 mm.
Ball Nose Cylinder
• Length 50 to 70 mm. • Head length 16 to 25 mm, Ø 6 to 13 mm.
Art. No. 616.630.312
Ball Nose Cylinder
• Length 38 mm. • Head length: 14 mm. • Head Ø 3 mm, Shank Ø 3 mm.
Art. No. 616.230.314
Art.Prefix: 616...
Ball
• Length 52 mm. • Head length 8 mm, Ø 10 mm.
Art. No. 616.361.008
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
59
DRILLING
S040 210 x 195 customer catalogue.qxp
S040 210 x 195 customer catalogue.qxp
Rd Tree
• Length 50 to 70 mm. • Head: length 16 to 25 mm, Ø 6 to 13 mm.
Art.Prefix: 616...
12:08
Page 60
Router Cutters
• Shank Ø 8 mm. • High quality router cutters manufactured containing cobalt. This manufacturing process extends the routers life span. • Available with and without relief. • Suitable for drainage slots etc. in UPVC profile. With relief:
Oval DRILLING
26/11/2008
Flame
• Length 76 mm. • Head: length 32 mm, Ø 13 mm.
Ø mm 4 5 5 6 8
L mm 90 80 90 90 100
• Tungsten carbide tipped. • Steel body. • To be used in portable or stationary machines, including CNC. • The router bits in the range are designed to cut hardwood and softwood, chipboard, MDF, plywood, composite worktops and other solid surface sheet materials.
Straight 2 Flute Plunge Cut
• Length 67 mm. • Head: length 22 mm, Ø 13 mm.
Art. No. 616.461.322
Würth Router Cutter Range
Cut/Relief mm 16 / 45 18 / 35 16 / 45 16 / 45 14 / 45
Art.No: 612.841.69 612.851.88 612.851.69 612.861.69 612.881.410
P/Qty 1 1 1 1 1
Art.No: 612.844.010 612.851.412 612.853.58 612.854.010 612.864.010 612.881.412
P/Qty 1 1 1 1 1 1
Without relief:
Shank Ø 12.7mm 6.4mm
Art. Prefix: 612.001... 612.000...
Straight Plunge Template Bits
Art. No. 616.561.332
Tree
• Length 50 to 64 mm. • Head length 16 to 19 mm, Ø 6 to 10 mm.
Art.Prefix: 616...
Cone
• Length: 67 mm. • Head length 22 mm, Ø 13 mm.
L mm 100 120 80 100 80 120
Cut mm 40 14 35 40 14 14
For our extensive range of power tools, See pages 159-179
Shank Ø 12.7mm 6.4mm
Art. Prefix: 612.021... 612.020...
Bevel Trim Bits
Shank Ø 12.7mm 6.4mm
www.winzerwurth.co.uk CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Art.No: 616.961.322
60
Ø mm 4 5 5 5 8 8
Art. Prefix: 612.031... 612.030...
S040 210 x 195 customer catalogue.qxp
Flush Trim Bits 2 Flute
26/11/2008
12:09
Page 61
Core Box Bits
• With ball bearing guide.
Bead Ovolo
• With ball bearing guide.
te na mi La
Art. Prefix: 612.041... 612.040...
Shank Ø 12.7mm
Art. Prefix: 612.091...
Cove Cutter
• With ball bearing guide.
• 14 degree.
Shank Ø 12.7mm 6.4mm
Art. Prefix: 612.051... 612.050...
Shank Ø 12.7mm 6.4mm
Art. Prefix: 612.101... 612.100...
Classical Template Bit • With ball bearing guide.
V-Grooving Bit
Art. Prefix: 612.141...
Edge Beading Bits
• With ball bearing guide.
Dovetail
Shank Ø 12.7mm
DRILLING
Shank Ø 12.7mm 1/4”
Shank Ø 12.7mm
Art. Prefix: 612.151...
Classic Ogee Bit
• With ball bearing guide.
• 90 degree.
Shank Ø 12.7mm Shank Ø 12.7mm
Art. Prefix: 612.061...
Art. Prefix: 612.121...
Plunging Classical Bit
Rabbeting Bit
Shank Ø 12.7mm
Art. Prefix: 612.161...
Classical Bit
• With ball bearing guide.
• With ball bearing guide.
Shank Ø 12.7mm Shank Ø 12.7mm
Art. Prefix: 612.171...
Shank Ø 12.7mm
Art. Prefix: 612.131...
Art. Prefix: 612.081...
www.winzerwurth.co.uk CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
61
S040 210 x 195 customer catalogue.qxp
Rounding Over Bit
DRILLING
12:11
Page 62
Plug Cutters
• With ball bearing guide.
Shank Ø 12.7mm
26/11/2008
• Self ejecting. • Heat treated and coated with an advanced surface treatment for extended work life.
• Head: 20 mm. • Length: 25 mm.
Art. Prefix: 612.071...
Roman Ogee Bit
Description acc.to DIN 69170 ZY2025
• With ball bearing guide. Shank Ø 8 mm Shank Ø 12.7mm
Cylindrical Cone Mounted Point
Art. Prefix: 612.181...
Key Hole Bits Single Flute
• Suitable for cutting “Key Hole” slots in pic ture frames, etc.
Art. Prefix: 612.010...
Mounted Points for Rough Grinding • • • •
• Head: 13 mm. • Length: 20 mm.
Special fused alumina, ceramically bound. Grit 30. Colour: pink. Specially suitable for grinding of steel.
Art. Prefix: 612.190...
Art. Prefix: 612.010...
9 Piece Assortment Description without shank, with drill bit
62
Art. No. 680.41
Art. Prefix: 612.010...
P/Qty 1/10
“A good, friendly, and reliable service.”
Counter Bores Carbide Tipped
Description with shank & drill bit
P/Qty 1/10
Tapered Mounted Point
Description acc.to DIN 69170 SP 1320
Shank Ø 6.4mm
Art. No. 680.51
Art. No. 680.10
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Mark, Blind Fitter, Sheffield.
26/11/2008
Hand Taps HSS
• DIN 352. • Plug tap sets. • Taps out metric isometric threads to DIN 13 standard. • Contents: 1st, 2nd and 3rd cut. • Sizes available M4 to M10. • Note: No’s denoted by rings on the shank, but No. 3 is left blank.
12:12
Page 63
Tap and Die Assortment HSS
• Contents: Taps, 1st, 2nd and 3rd cut of the following sizes; 3, 4, 5, 6, 8, 10, 12 mm. dies, 3, 4, 5, 6, 8, 10, 12 mm. Stocks, 1 each of; 20 x 5, 20 x 7, 25 x 9, 30 x 11, 38 x 14. Tap holders - adjustable no’s; 1 + 2.
Adjustable Tap Wrench • • • • • •
DIN 1814. Size: No. 2. Length 280 mm. For square shank 3.4 to 7 mm. For metric taps 4 to 12 mm. Can be used with taps, with a square shank DIN 10.
• For blind holes. • Contains: Machine Tap Drills: M3 / M4 / M5 / M6 / M8 / M10 / M12 Core Hole Drills: 2.5 / 3.3 / 4.2 / 5.0 / 6.8 / 8.5 / 10.2 mm
Machine tap HSS-E Zebra Blue Ring
Hand Tap Assortment
Art. Prefix: 639.01
Zebra Blue Ring
Art. No. 653.01
Art. Prefix: 639...
• DIN 352. • Taps out metric iso metric threads to DIN 13 standard. • Contents: 1st, 2nd and 3rd cut of the following sizes; 3, 4, 5, 6, 8, 10, 12 mm.
Machine Tap Assortment with Tapping Size Drills
Art. No. 965.92.100
Combination Screw Tap Bits HSS
• Ground precision tool for drilling, tapping, de-burring and countersinking in one operation. • Sizes available Ø M4 to M10. • Safe power transmission by 6.4mm hexagonal shaft. • Suitable for tapping through holes in steel, non-ferrous metal and plastic materials up to 6mm deep.
• For use in steel, high tensile steel, cast steel, aluminium, brass, copper, plastic. • For through holes: straight grooved, 4speed cut, form B with curling cut, tap relief: ground flanks. • Thread depth: M3 - M10 approx. 3 - 5 x Ø. • centring: full point on cutting part, shaft with chamfer centring.
DIN 371 with reinforced shaft
Art. Prefix: 653...
DIN 376 Art. No. 653.9...
Art. No. www.winzerwurth.co.uk 653.12 CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Art. No. 657.2
63
DRILLING
S040 210 x 195 customer catalogue.qxp
S040 210 x 195 customer catalogue.qxp
26/11/2008
Machine tap HSS-E
Page 64
SDS-Plus Chisels
Zebra Blue Ring
• For blind holes: 40° right-hand grooved, short cut 2 - 3 speed, Form C, tap relief: ground flanks. • DIN 371 with reinforced shaft. • Thread depth: approx. 3 x Ø. • Centring: full point on cutting part, shaft with chamfer centring.
DRILLING
12:13
• All chisels in this range will fit all current machines with longitudinal and circular grooves and circular only. • Chisels can be re-sharpened by simply regrinding. • Chisels can be changed instantly, simply by pushing the tool in and releasing it.
Pointed Chisel
Art. Prefix: 653.0... L mm 250
Machine tap HSS-E Zebra Green Ring
• For stainless steel. • For through holes: straight grooved, 4 speed cut, form B with curling cut, tap relief: outer and flanks ground. • DIN 371 with reinforced shaft, thread depth: M4 - M10 approx. 3 - 5 x Ø. • centring: full point on cutting part, shaft with chamfer centring.
Art. No. 648.925.0
L mm 250
Head W mm 20
Art. No. 648.920.250
Drill Ø mm 50 105
Teeth 6 6
Art. No. 632.150 632.110.5
P/Qty 1 1
Application Range:
Art. Prefix: 655...
Art. No. 632.150
• Thread repair sets • Sets available in M6, M8, M10, M12. • Insert refills available in packs of 25 each. Sets Art. Prefix: 661... Insert Refill Art. Prefix: 663...
64
• For precision drills and 4kg hammer drills. • Length: 75 mm. • 6 sintered hard carbide cutting edges enable fast penetration and guarantee a long service life. • M16 internal thread. • Max. 60 mm drill depth per working stage. • Required machine output: ï Ø 50 mm min. 600W ï Ø 50 mm min. 800W • Suitable for concrete, brick work, limited suitability for natural stone depending on their strength. • Caution: only suitable for machines with safety clutch and additional handle.
Flat Chisel
Bolster Time Sert
Hammer Drill Crowns
632.110.5 L mm 250
Head W mm 35
Art. No. 648.935.250
Application Ø mm Heating pipes with 50 insulation Air conditioner pipes with 100 insulation
Insertion Shaft: Description Hex, A/F 11 mm for drilling machine For SDS drilling machine
Hollow Chisel
Total L mm 78
Art. No. 630.005
P/Qty 1
105 220
630.008 630.009
1 1
Centre Drill for Masonry:
• With sintered hard carbide cutting edge.
L mm 250
Head W mm 22
Art. No. 648.922.250
Drill bit Ø mm 9
L mm 120
CALL NOW! 0870 950 2800 FOR FURTHER DETAILS.
Art. No. 630.08.120
P/Qty 1