SUBMITTAL JOB:
REPRESENTATIVE:
UNIT TAG:
ORDER NO.
DATE:
ENGINEER:
SUBMITTED BY:
DATE:
CONTRACTOR:
APPROVED BY:
DATE:
NRF - System Lubricated Iron Body Circulators DESCRIPTION
CONSTRUCTION MATERIALS
A flanged in-line system lubricated circulating pump designed specifically for quiet operation in a closed hydronic heating system.
Pump Body: Cast Iron Impeller: Noryl Shaft: Ceramic Bearings: Carbon
OPERATING DATA Maximum Working Pressure: 150 psi (10.3Bar) Minimum Operating Temperature: 40°F (5°C) Maximum Operating Temperature NRF-22 & NRF-9F/LW: 240°F (115°C) NRF-25, NRF-33, NRF-36 & NRF-45: 225°F (107°C) SCHEDULE
*
STANDARD 60 CYCLE SINGLE PHASE MOTOR CHARACTERISTICS F.L. WATTS VOLTAGE AMPS RPM 41 115 .40 2800
MODEL NUMBER NRF-9F/LW
PART NUMBER 103267
NRF-22
103251
92
115
.80
2940
NRF-25 *
103417
125
115
1.1
2950
NRF-33
103350
125
115
1.1
2950
NRF-36 *
103400
270
115
2.1
3300
NRF-45 *
103404
270
115
2.1
3300
Three-speed pump
TAGGING INFORMATION
QUANTITY
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
A-126H
System Lubricated Iron Body Circulators Model NRF
A-126H
*
C is center-to-center dimension of bolt holes. Flange orientation varies.
TYPICAL SPECIFICATIONS The contractor shall furnish and install in-line circulating pumps as illustrated on the plans and in accordance with the following specifications: 1. The pumps shall be of the horizontal, system lubricated type specifically designed and guaranteed for quiet operation. 2. Pumps to be suitable for _____°F (_____°C) [Select one: 240°F (115°C) for NRF-22 and NRF-9F/LW; 225°F (107°C) for NRF-25, NRF-33, NRF-36 and NRF-45] operation at 150 psig (10.3 Bar) working pressure. 3. The pumps shall have a ceramic shaft supported by carbon bearings. Bearings are to be lubricated by the circulating fluid. 4. Motor stator to be isolated from circulating fluid through use of stainless steel can. Rotor to be sheathed in stainless steel. 5. Motors shall be non-overloading at any point on the pump curve. (Select one: NRF-9F/LW, NRF-22, NRF-25, NRF-33) motors to have built-in impedance protection. (Select one: NRF-36, NRF-45) motors to have built-in thermal protection. 6. [Select one: NRF-25, NRF-36 or NRF-45] is available with 3-speed, thermally protected motor covering a wide range of hydraulic capabilities. 7. The pump manufacturer shall be ISO-9001 certified. Pumps to have a capacity of __________ GPM at ________ foot head when powered by 115 volt, 60 cycle, single phase electrical supply. All pumps are to be Bell and Gossett Model NRF-__________.
MODEL
PART NUMBER
A in (mm)
B in (mm)
C in (mm)
D in (mm)
E in (mm)
F in (mm)
G in (mm)
Weight (lb)
NRF-9F/LW
103267
5-1/8 (130)
3-3/16 (81)
3-3/16 (81)
6-3/16 (157)
4-5/16 (110)
6-3/8 (162)
3-3/16 (81)
9.3
NRF-22
103251
5-1/8 (130)
3-3/16 (81)
3-3/16 (81)
6-3/16 (157)
4-5/16 (110)
6-3/8 (162)
3-3/16 (81)
9.3
NRF-25 *
103417
5-1/8 (130)
3-3/16 (81)
3-3/16 (81)
6-3/16 (157)
4-7/8 (124)
6-3/8 (162)
3-7/8 (98)
10.4
NRF-33
103350
5-1/8 (130)
3-3/16 (81)
3-3/16 (81)
6-3/16 (157)
3-11/16 (94)
6-3/8 (162)
3-3/16 (81)
10.4
NRF-36
103400
5-3/4 (146)
3-9/16 (91)
3-3/16 (81)
6-7/8 (175)
5-3/8 (137)
6-3/8 (162)
3-3/16 (81)
13.1
NRF-45 *
103404
5-3/4 (146)
3-9/16 (91)
3-7/16 (87)
7-3/8 (187)
5-1/2 (140)
8-1/2 (216)
4-1/4 (108)
14.5
Dimensions are subject to change. Not to be used for construction purposes unless certified.
Companion Flanges Available in Sizes: 3/4", 1", 1-1/4" and 1-1/2" Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.bellgossett.com Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2013 Xylem Inc.
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
PUMP PERFORMANCE CURVE
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
SUBMITTAL A-123B
JOB:
REPRESENTATIVE:
UNIT TAG: ENGINEER:
ORDER NO. SUBMITTED BY:
DATE: DATE:
CONTRACTOR:
APPROVED BY:
DATE:
Series LR Iron & Lead-Free† Bronze Booster Pumps Where potable water is pumped, use a lead-free† bronze Series LR circulator.
DESCRIPTION The Series LR is a flanged in-line system lubricated circulating pump designed specifically for quiet operation in closed loop systems. The Series LR is available in cast iron body construction for hydronic heating systems or lead-free † bronze body construction for potable water applications.
CONSTRUCTION Pump Body LR-20WR: Cast Iron LR-15BWR:Lead-Free† Bronze Impeller: Noryl® Shaft: Ceramic Bearings: Carbon †
Contains less than 0.25% Lead content by weight on wetted surfaces.
OPERATING DATA Maximum working pressure: 150 psig (10 bar) Maximum operating temperature: 225°F (107°C)
Standard 60 Cycle Motor Characteristics
Part Number
Pump Body Material
Flange Sizes Inches-NPT
Watts
Voltage
F.L. Amps
RPM
LR-20WR
106507
Cast Iron
3/4, 1, 1-1/4, 1-1/2
125
115
1.1
2950
LR-15BWR
106514LF
3/4, 1, 1-1/4, 1-1/2
125
115
1.1
2950
Model Number
Lead-Free†
Bronze
Tagging
Quantity
A-123B
PUMP PERFORMANCE CURVE
TYPICAL SPECIFICATIONS The contractor shall furnish and install in-line circulating pumps as illustrated on the plans and in accordance with the following specifications: 1. The pump shall be of the horizontal system lubricated type specifically designed and guaranteed for quiet operation. 2. Pump to be suitable for 225º F (107º C) operation at 150 PSIG (10 Bar) working pressure. 3. The pumps shall have a ceramic shaft supported by carbon bearings. Bearings are to be lubricated by the circulating fluid.
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.xyleminc.com/brands/bellgossett Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2012 Xylem Inc.
4. Motor stator to be isolated from circulating fluid through use of stainless steel can. Rotor to be sheathed in stainless steel. 5. Motors shall be non-overloading at any point on the pump curve. Motors to have built-in impedance protection. 6. The pump manufacturer shall be ISO-9001 certified. Pumps to have a capacity of __________ GPM at ________ foot head when powered by 115 volt, 60 cycle, single phase electrical supply. All pumps are to, ITT Industries−Bell & Gossett Model LR___________.
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
Series LR System Lubricated Circulators
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
SUBMITTAL A-135G
JOB:
REPRESENTATIVE:
UNIT TAG:
ORDER NO.
DATE:
ENGINEER:
SUBMITTED BY:
DATE:
CONTRACTOR:
APPROVED BY:
DATE:
Permanently Lubricated Iron & Lead-Free† Bronze Booster Pumps DESCRIPTION
CONSTRUCTION MATERIALS
The Series PL™ close coupled booster pumps are specifically designed for quiet operation in hydronic, radiant and geothermal heating and cooling systems. These inline permanently lubricated pumps are available in cast iron or lead-free† bronze body construction.
Booster Body: Cast Iron or Lead-Free† Bronze Face Plate: Stainless Steel Impeller: 30% Glass Filled Noryl® (PL-55 & PL-130): Glass Filled PPS Shaft: Carbon Steel (PL-55 & PL-130): Stainless Steel Shaft Sleeve: Stainless Steel (PL-55 & PL-130): None Seal: Mechanical, Carbon on Silicon Carbide Motor Bearings: Sealed Precision Steel Ball Bearing Permanently Lubricated Motor Type: ODP Elastomers: EPDM
OPERATING DATA Maximum working Pressure: 150 psi (10 Bar) Maximum Operating Temperature: 225°F (107°C) †
Contains less than 0.25% Lead content by weight on wetted surfaces.
SCHEDULE CAST IRON MODEL NUMBER PL-30 PL-30 PL-36 PL-36 PL-36 PL-45 PL-45 PL-45 PL-50 PL-50 PL-50 PL-55 PL-55 PL-55 PL-75 PL-75 PL-75 PL-130/2" PL-130/2" PL-130/2" PL-130/3" PL-130/3" PL-130/3"
PART NUMBER 1BL012 1BL014 1BL001 1BL006 1BL116 1BL002 1BL007 1BL121 1BL016 1BL018 1BL123 1BL032 1BL033 1BL115 1BL034 1BL036 1BL125 1BL063 1BL064 1BL127 1BL070 1BL071 1BL130
QTY.
LEAD-FREE† BRONZE MODEL NUMBER PART NUMBER PL-30B 1BL013LF PL-30B 1BL015LF PL-36B 1BL003LF PL-36B 1BL008LF PL-36B 1BL118LF PL-45B 1BL004LF PL-45B 1BL009LF PL-45B 1BL122LF PL-50B 1BL017LF PL-50B 1BL019LF PL-50B 1BL124LF PL-55B 1BL068LF PL-55B 1BL069LF PL-55B 1BL119LF PL-75B 1BL035LF PL-75B 1BL037LF PL-75B 1BL126LF PL-130B/2" 1BL065LF PL-130B/2" 1BL066LF PL-130B/2" 1BL128LF PL-130B/3" 1BL072LF PL-130B/3" 1BL073LF PL-130B/3" 1BL131LF
QTY.
Note: Where potable water is pumped, use a lead-free † bronze booster. PL boosters equipped with a drip-proof motor are recommended for indoor use only.
STANDARD 60 CYCLE SINGLE PHASE MOTOR CHARACTERISTICS HP VOLTAGE F.L. AMPS RPM 1/12 115 1.4 2650 1/12 230 0.8 2650 1/6 115 2.1 3300 1/6 230 1.1 3300 1/6 277 1 3300 1/6 115 2.1 3300 1/6 230 1.1 3300 1/6 277 1 3300 1/6 115 1.8 3300 1/6 230 1.0 3300 1/6 277 1.0 3300 2/5 115 4.7 3250 2/5 230 2.4 3250 2/5 277 1.9 3250 1/6 115 2.1 3400 1/6 230 1.1 3400 1/6 277 1 3400 2/5 115 4.8 3200 2/5 230 2.4 3200 2/5 277 1.9 3200 2/5 115 4.8 3200 2/5 230 2.4 3200 2/5 277 1.9 3200
TAGGING INFORMATION
SERIES PL - Permanently Lubricated Booster Pumps
A-135G
DIMENSIONS AND WEIGHTS MODEL NO. PL-30 PL-36 PL-45 PL-50 PL-55 PL-75 PL-130/2" PL-130/3"
FLANGE SIZE INCHES NPT 3/4, 1, 1-1/4 & 1-1/2 3/4, 1, 1-1/4 & 1-1/2 1, 1-1/4 & 1-1/2 1, 1-1/4 & 1-1/2 3/4, 1, 1-1/4 & 1-1/2 2 2 3
MOTOR HP
A
B
C
D
E
APPROXIMATE SHIPPING WT. LBS. (KG)
1/12
8 5/8 (219)
6 3/8 (162)
7 1/8 (181)
4 3/16 (106)
4 3/8 (111)
11.6 (5.3)
1/6
8 5/8 (219)
6 3/8 (162)
7 1/8 (181)
4 3/16 (106)
4 3/8 (111)
13.1 (6.0)
1/6
9 1/8 (232)
8 1/2 (216)
7 1/4 (184)
4 5/8 (117)
4 1/2 (114)
14.5 (6.6)
1/6
9 1/8 (232)
8 1/2 (216)
7 1/4 (184)
4 5/8 (117)
4 1/2 (114)
14.5 (6.6)
2/5
9 9/16 (243)
6 3/8 (162)
7 15/16 (202)
4 3/16 (106)
4 3/4 (121)
13.1 (6.0)
1/6 2/5 2/5
9 15/16 (252) 10 3/4 (273) 10 3/4 (273)
8 1/2 (216) 8 1/2 (216) 8 1/2 (216)
7 3/8 (187) 8 1/4 (210) 8 1/4 (210)
5 3/16 (132) 5 3/16 (132) 6 (152)
4 5/8 (117) 5 1/8 (130) 5 1/8 (130)
18.5 (8.4) 22 (10) 27 (12.2)
DIMENSIONS - INCHES (mm)
Dimensions are approximate and subject to change. Contact factory for certified dimensions.
TYPICAL SPECIFICATIONS The contractor shall furnish and install inline pumps as illustrated on the plans and in accordance with the following specifications: 1. The pumps shall be of the horizontal, permanently lubricated type, specifically designed and guaranteed for quiet operation. 2. The pumps shall have a steel shaft supported by permanently lubricated, sealed precision ball bearings. The pumps are to be equipped with a water-tight seal to prevent leakage. Mechanical seal faces to be carbon on silicon carbide. The motor shall be non-overloading at any point on the pump performance curve. 3. The motor shall be of the drip-proof, sealed precision ballbearing, quiet-operating construction. The permanent splitcapacitor motor shall be equipped with thermal overload protection. 4. Pumps to be suitable for 225°F (107°C) operating temperature at 150 psig (10 bar) working pressure. The pumps shall be Bell & Gossett, A Xylem brand. Model No. PL-__________ with a capacity of __________ GPM at __________ feet of head.
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.bellgossett.com Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2014 Xylem Inc.
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
PERFORMANCE CHARACTERISTICS CURVES
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
SUBMITTAL A-120H JOB:
REPRESENTATIVE:
UNIT TAG:
ORDER NO.
ENGINEER:
SUBMITTED BY:
CONTRACTOR:
DATE: DATE: DATE:
APPROVED BY:
Iron & Lead-Free† Bronze* Booster Pump *Where potable water is supplied, use a lead-free† bronze pump.
DESCRIPTION Bell & Gossett in-line three-piece booster pumps are designed for hydronic systems. Series 100 and HV are Listed with Underwriter's Laboratories. CONSTRUCTION
OPERATIONAL DATA Maximum Working Pressure: 125 PSI (682 kPa) Maximum Operating Temperature: - Standard Seal: 225°F (107°C) continuous - Special Seals: 250°F (121°C) continuous (consult local B&G Representative) Maximum Motor RPM: 1750
Body: Cast Iron or Lead-Free† Bronze Seal: Mechanical, Carbon on Ceramic Shaft: Carbon Steel, Heat Treated Pump and Motor Bearings: −All except PD-38 and PD-40: Bronze Sleeve, Oil Lubricated −PD-38 and PD-40: Ball Bearing, Permanently Lubricated Coupler: −All except PD38 and PD40: Flexible, Spring type −PD38 and PD40: Flexible, sleeve type. Motor: Bell & Gossett 1/12 hp thru 1-1/2 hp standard single and three phase dripproof motors are Recognized under the Component Program of Underwriter's Laboratories, Inc. Bell & Gossett boosters with their respective Bell & Gossett manufactured standard 60 hertz single and three phase motors are Certified by CSA.
IMPELLER: PUMP MODEL NO. Series 100® Pump Series HV & 2 PR, 2-1/2, LD3 HD3, PD35, PD37 PD38 & PD40
IRON BODY Polypropylene* or Lead-Free† Brass Phenolic* or Lead-Free† Brass Steel, Zinc Plated or Lead-Free† Brass Steel, Zinc Plated or Lead-Free† Brass Cast Iron or Lead-Free† Brass
BRONZE BODY Polypropylene* or Lead-Free† Brass Phenolic* or LeadFree† Brass Lead-Free† Brass Lead-Free† Brass Lead-Free† Brass
* System temperatures above 225 °F (107 °C) require a brass impeller. † Contains less than 0.25% Lead content by weight on wetted surfaces.
SCHEDULE **STANDARD 60 CYCLE CHARACTERISTICS FLANGE SIZE NPT INCHES HP PH VOLTAGE* F.L. AMPS RPM 3/4, 1, Series 100 1/12 1 115 1.75 1725 1-1/4 & 1-1/2 3/4, 1, Series PR 1/6 1 115 1.9 1725 1-1/4 & 1-1/2 1, 1-1/4 Series HV 1/6 1 115 1.9 1725 & 1-1/2 2 2 1/6 1 115 1.9 1725 2-1/2 2-1/2 1/4 1 115 3.0 1725 LD3 3 1/4 1 115 3.0 1725 HD3 3 1/3 1 115/230 4.2/2.1 1725 PD-35S 3 1/2 1 115/230 5.2/2.6 1725 PD-35T 3 1/2 3 208-230/460 1.8-1.7/.85 1750 PD-37S 3 3/4 1 115/230 7.0/3.5 1725 PD-37T 3 3/4 3 208-230/460 2.45-2.4/1.2 1750 PD-38S 3 1 1 115/230 9.8/4.5 1725 PD-38T 3 1 3 208-230/460 3.4-3.4/1.7 1725 PD-40S 3 1-1/2 1 115/230 18.0/9.0 1725 PD-40T 3 1-1/2 3 208-230/460 4.8-4.8/2.4 1725 **Motors with special electrical characteristics are available on request at additional cost. *1 PH Motors: Built-in overload protection 3 PH Motors: Overload protection must be provided Bell & Gossett Booster Pumps equipped with a drip-proof motor are recommended for indoor use only. MODEL NO.
TAGGING INFORMATION
QUANTITY Iron Body Bronze Body STD BI BI NFI
−
− − − − − − − − − − −
MODEL NO. Series 100 Series PR Series HV 2
FLANGE SIZE NPT INCHES 3/4, 1, 1-1/4 & 1-1/2 3/4, 1, 1-1/4 & 1-1/2 1, 1-1/4 & 1-1/2 2
2-1/2
2-1/2
LD3
3
HD3
3
PD-35S
3
PD-35T
3
PD-37S
3
PD-37T
3
PD-38S
3
PD-38T
3
PD-40S
3
PD-40T
3
DIMENSIONS IN INCHES (MM) A
B
C
14-7/8 (378) 15-1/4 (387) 15-3/8 (391) 16-5/8 (422) 17-1/4 (438) 17-1/4 (438) 17-1/2 (444) 20-1/4 (514) 20-1/4 (514) 20-1/4 (514) 20-1/4 (514) 22-11/16 (576) 23-15/16 (608) 24-3/4 (629) 21-7/8 (556)
6-3/8 (162) 8-1/2 (216) 8-1/2 (216) 8-1/2 (216) 10 (254) 10 (254) 10 (254) 12 (305) 12 (305) 12 (305) 12 (305) 14-1/2 (368) 14-1/2 (368) 14-1/2 (368) 14-1/2 (368)
12-3/4 (324) 12-3/4 (324) 13 (330) 14 (356) 14 (356) 14 (356) 14-1/4 (362) 16-7/8 (429) 16-7/8 (429) 16-7/8 (429) 16-7/8 (429) 18-15/16 (481) 20-3/16 (513) 21 (533) 18-1/8 (460)
Dimensions are subject to change. Not to be used for construction purposes unless certified.
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.xyleminc.com/brands/bellgossett Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2012 Xylem Inc.
A-120H
APPROX. SHPG. WT. LBS. (Kg) IRON BRONZE BODY BODY 20 (9) 30 (14) 28 (13) 36 (16) 54 (24) 53 (24) 55 (25) 75 (34) 75 (34) 75 (34) 75 (34) 128 (58) 125 (57) 130 (59) 127 (58)
21 (10) 32 (15) 30 (14) 39 (18) 58 (26) 57 (26) 59 (27) 80 (36) 80 (36) 80 (36) 80 (36) 138 (63) 135 (61) 140 (64) 137 (62)
Electrical Box Arrangement for pumps with B&G Manufactured Motors MODEL NO. #1 #2 #3 #4 Series 100 Series HV, PR & 2 2-1/2", LD3 & HD3 PD35 & PD37 PD38 & PD40
115 & 230Volt 60Hz 1PH 110 & 220Volt 50Hz 1PH 115 & 230Volt 60Hz 1PH 110 & 220Volt 50Hz 1PH − − −
−
−
−
−
3PH
−
1PH − −
− ALL −
− − ALL
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
Iron & Bronze Booster Pump Submittal
TYPICAL SPECIFICATIONS The Contractor shall furnish and install In-The-Line pumps as illustrated on the plans and in accordance with the following specifications: 1. The pumps shall be of the horizontal, oil-lubricated type. (Except PD-38, PD40 are permanently lubricated) Specifically designed and guaranteed for quiet operation. Suitable for 125# (862 kPa) working pressure. 2.The pumps shall have a ground and polished steel shaft with a hardened integral thrust collar. The shaft shall be supported by two horizontal sleeve bearings designed to circulate oil. (Except PD-38, PD-40 are grease lubricated ball bearing design) The pumps are to be equipped with a mechanical seal with carbon seal face rotating against a ceramic seat. The motor shall be nonoverloading at any point on pump curve. 3. The motor shall be of the drip-proof, sleeve-bearing, (Except PD-38, PD-40 are ball bearing) quiet operating, rubber-mounted construction. Motors shall have built-in thermal overload protectors. (Exception - PD models with 3-phase motors, see paragraph 4.) 4. For PD models with 3-phase motors, add the following: The Contractor shall furnish and install a magnetic starter for each booster pump with at least two thermal overload protectors. The starter shall be equipped with manual reset buttons. All Units must be ITT Bell & Gossett Model No. ________, or approved equal with capacity of ______GPM at ______ft. head when directly driven through a self aligning flexible coupling by an oil lubricated motor, _____volts ____cycle___phase.
SUBMITTAL B-148A JOB:
REPRESENTATIVE:
UNIT TAG:
ORDER NO.
DATE:
ENGINEER:
SUBMITTED BY:
DATE:
CONTRACTOR:
APPROVED BY:
DATE:
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
Series 60 Stock Pumps Maintenance Free In-Line Mounted Pump SPECIFICATIONS FLOW HP
MATERIALS OF CONSTRUCTION/FEATURES HEAD RPM
VOLTS CYCLE
PHASE
© COPYRIGHT 2010 ITT Corporation
1750 RPM ODP MOTOR FACTORY TESTED THREE YEAR WARRANTY INTERNAL SELF-FLUSHING MECHANICAL SEAL 175 PSI (12bar) MAX.W.P XLii LUBRICATION SYSTEM BURA/CARBON-CERAMIC SEAL (-20°F TO 225°F) BRONZE FITTED OR ALL BRONZE CONSTRUCTION
Bell & Gossett
Series 60 Stock Centrifugal Pump Submittal
B-148A
MODEL
SUCTION AND DISCHARGE SIZE INCHES NPT
F
G
K
L
M
N
P
R
S
T
601,602 & 603
1
6-7/16 (164)
3-7/16 (87)
3-5/8 (92)
1-3/8 (35)
2-1/2 (64)
7-1/2 (190)
3/4 (19)
5 (127)
6 (152)
11 (279)
604,605 & 606
1-1/4
6-7/16 (164)
3-7/16 (87)
3-5/8 (92)
1-3/8 (35)
2-1/2 (64)
7-1/2 (190)
3/4 (19)
5 (127)
6 (152)
11 (279)
607,608 & 609
1-1/2
6-9/16 (167)
3-5/8 (92)
3-3/4 (95)
1-3/8 (35)
2-3/4 (70)
7-7/8 (200)
3/4 (19)
5 (127)
6-1/2 (165)
11-1/2 (292)
PUMP DIMENSION IN INCHES (MM)
613,614 & 621
1-1/2
6-11/16 (170)
3-3/8 (86)
4-1/16 (103)
1 (25)
3-9/16 (90)
8-9/16 (217)
3/4 (19)
6-1/2 (165)
7 (176)
13-1/2 (343)
617,618,622 & 623
1-1/2
9-3/8 (238)
3-1/4 (83)
4-5/8 (117)
1 (25)
3-7/8 (98)
9-1/2 (241)
3/4 (19)
6-1/2 (165)
7 (176)
13-1/2 (343)
610,611 & 612
2
6-11/16 (170)
3-3/4 (95)
3-3/4 (95)
1-3/8 (35)
2-7/8 (73)
8 (203)
13/16 (21)
5 (127)
6-1/2 (165)
11-1/2 (292)
615,616
2
6-15/16 (170)
3-1/2 (89)
4-3/8 (111)
1 (25)
4 (102)
9-3/8 (238)
13/16 (21)
6-1/2 (165)
7 (176)
13-1/2 (343)
619,620 &624
2
9-3/8 (238)
3-1/2 (89)
4-3/4 (121)
1 (25)
4-1/8 (105)
9-7/8 (251)
13/16 (21)
6-1/2 (165)
7-1/2 (165)
14 (356)
Maximium working pressure 175 PSI (12 Bar)
PART #
MODEL
PUMP SIZE
HP
IMP DIA
A
B
C
D
E
H
APP WEIGHT LBS
172701LF
601S
1x1x5-1/4
1/4
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
48
172704LF
B601S
1x1x5-1/4
1/4
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
48
172947LF
602S
1x1x5-1/4
1/3
4.84"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
53
172705LF
B602S
1x1x5-1/4
1/3
4.84"
10-1/8 (527)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
53
172703LF
603S
1x1x5-1/4
1/2
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
21-1/8 (537)
55
172706LF
B603S
1x1x5-1/4
1/2
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
21-1/8 (537)
55
172707LF
604S
1-1/4x1-1/4x5-1/4
1/4
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
50
172709LF
B604S
1-1/4x1-1/4x5-1/4
1/4
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
50
172708LF
605S
1-1/4x1-1/4x5-1/4
1/3
4.84"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
55
172710LF
B605S
1-1/4x1-1/4x5-1/4
1/3
4.84"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
55
172667LF
606S
1-1/4x1-1/4x5-1/4
1/2
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
57
172711LF
B606S
1-1/4x1-1/4x5-1/4
1/2
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
57
172712LF
607S
1-1/2x1-1/2x5-1/4
1/3
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
20-3/16 (513)
59
172714LF
B607S
1-1/2x1-1/2x5-1/4
1/3
4.38"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
10 (254)
20-3/16 (513)
59
172713LF
608S
1-1/2x1-1/2x5-1/4
1/2
4.94"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
61
172715LF
B608S
1-1/2x1-1/2x5-1/4
1/2
4.94"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
61
172668LF
609S
1-1/2x1-1/2x5-1/4
3/4
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
63
172716LF
B609S
1-1/2x1-1/2x5-1/4
3/4
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
63
172717LF
610S
2x2x5-1/4
1/2
4.12"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
63
172719LF
B610S
2x2x5-1/4
1/2
4.12"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
63
172718LF
611S
2x2x5-1/4
3/4
4.75"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
71
172720LF
B611S
2x2x5-1/4
3/4
4.75"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
71
172669LF
612S
2x2x5-1/4
1
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
78
172721LF
B612S
2x2x5-1/4
1
5.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
78
172948LF
626S
3x3x5-1/4
3/4
4.375"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
20-7/16 (520)
77
172950LF
B626S
3x3x5-1/4
3/4
4.375"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
20-7/16 (520)
77
172952LF
627S
3x3x5-1/4
1-1/2
5.25"
8-3/4 (222)
2-1/4 (57)
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
21-1/8 (536)
87
172954LF
B627S
3x3x5-1/4
1-1/2
5.25"
8-3/4 (222)
2-1/4 (57)
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
21-1/8 (536)
87
172755LF
621S
1-1/2x1-1/2x6-1/4
1/2
4.88"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
66
172771LF
B621S
1-1/2x1-1/2x6-1/4
1/2
4.88"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
66
172722LF
613S
1-1/2x1-1/2x6-1/4
3/4
5.75"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
68
172670LF
614S
1-1/2x1-1/2x6-1/4
1
6.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
9-3/4 (248)
21-7/16 (545)
85
172773LF
B614S
1-1/2x1-1/2x6-1/4
1
6.25"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
9-3/4 (248)
21-7/16 (545)
85
172723LF
615S
2x2x6-1/4
3/4
5.62"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
77
172775LF
B615S
2x2x6-1/4
3/4
5.62"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
77
172671LF
616S
2x2x6-1/4
1
6.22"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/4 (121)
9-3/4 (248)
21-7/16 (545)
86
172757LF
622S
1-1/2x1-1/2x7
3/4
5.50"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
81
172758LF
623S
1-1/2x1-1/2x7
1
6.0"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
90
172724LF
617S
1-1/2x1-1/2x7
1-1/2
6.5"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
102
172761LF
624S
2x2x7
1
5.69"
10-1/8 (257)
2-1/4 (57)
7-7/8 (200)
4-3/4 (121)
11 (279)
23-5/8 (600)
95
172762LF
625S
2x2x7
1-1/2
6.12"
8-3/4 (222)
2-1/4 (57)
6-1/2 (200)
3-1/4 (83)
10-3/4 (273)
21-5/8 (549)
108
© COPYRIGHT 2010 ITT Corporation
Bell & Gossett
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
Single phase 115V/230V, "B" model stands for all bronze construction. Dimensions-Inches (mm)
Series 60 Stock Centrifugal Pump Submittal
B-148A
Three phase 208-230V/460V, "B" model stands for all bronze construction. Dimensions -Inches (mm) MODEL
PUMP SIZE
HP
IMP DIA
A
B
C
D
E
H
APP WEIGHT LBS
172725LF
601T
1x1x5-1/4
1/4
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
48
172728LF
B601T
1x1x5-1/4
1/4
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
48
172726LF
602T
1x1x5-1/4
1/3
4.84"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
53
172729LF
B602T
1x1x5-1/4
1/3
4.84"
7-7/8 (20)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
53
172727LF
603T
1x1x5-1/4
1/2
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
55
172730LF
B603T
1x1x5-1/4
1/2
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
55
172731LF
604T
1-1/4x1-1/4x5-1/4
1/4
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
50
172734LF
B604T
1-1/4x1-1/4x5-1/4
1/4
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
50
172732LF
605T
1-1/4x1-1/4x5-1/4
1/3
4.84"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
55
172735LF
B605T
1-1/4x1-1/4x5-1/4
1/3
4.84"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
19-7/8 (505)
55
172733LF
606T
1-1/4x1-1/4x5-1/4
1/2
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
57
172736LF
B606T
1-1/4x1-1/4x5-1/4
1/2
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-1/8 (537)
57
172737LF
607T
1-1/2x1-1/2x5-1/4
1/3
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
20-7/16 (519)
59
172740LF
B607T
1-1/2x1-1/2x5-1/4
1/3
4.38"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
10 (254)
20-7/16 (519)
59
172738LF
608T
1-1/2x1-1/2x5-1/4
1/2
4.94"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
61
172741LF
B608T
1-1/2x1-1/2x5-1/4
1/2
4.94"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
61
172739LF
609T
1-1/2x1-1/2x5-1/4
3/4
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
63
172742LF
B609T
1-1/2x1-1/2x5-1/4
3/4
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
63
172743LF
610T
2x2x5-1/4
1/2
4.12"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
63
172746LF
B610T
2x2x5-1/4
1/2
4.12"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
63
172744LF
611T
2x2x5-1/4
3/4
4.75"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
71
172747LF
B611T
2x2x5-1/4
3/4
4.75"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-11/16 (551)
71
172745LF
612T
2x2x5-1/4
1
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
78
172748LF
B612T
2x2x5-1/4
1
5.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
78
172949LF
626T
3x3x5-1/4
3/4
4.375"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
20-7/16 (520)
77
172951LF
B626T
3x3x5-1/4
3/4
4.375"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
20-7/16 (520)
77
172953LF
627T
3x3x5-1/4
1-1/2
5.25"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
21-1/8 (536)
87
172955LF
B627T
3x3x5-1/4
1-1/2
5.25"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
21-1/8 (536)
87
172756LF
621T
1-1/2x1-1/2x6-1/4
1/2
4.88"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
66
172772LF
B621T
1-1/2x1-1/2x6-1/4
1/2
4.88"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
66
172749LF
613T
1-1/2x1-1/2x6-1/4
3/4
5.75"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/6 (541)
68
172750LF
614T
1-1/2x1-1/2x6-1/4
1
6.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/16 (541)
85
172774LF
B614T
1-1/2x1-1/2x6-1/4
1
6.25"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-5/16 (541)
85
172751LF
615T
2x2x6-1/4
3/4
5.62"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
77
172776LF
B615T
2x2x6-1/4
3/4
5.62"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
21-7/16 (545)
77
172752LF
616T
2x2x6-1/4
1
6.22"
7-7/8 (200)
-
7-7/8 (200)
4-3/4 (121)
9-3/4 (248)
21-7/16 (545)
86
172759LF
622T
1-1/2x1-1/2x7
3/4
5.50"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
11 (279)
23-5/8 (600)
81
172760LF
623T
1-1/2x1-1/2x7
1
6.0"
7-7/8 (200)
-
7-7/8 (200)
4-3/4 (121)
11 (279)
23-5/8 (600)
90
172753LF
617T
1-1/2x1-1/2x7
1-1/2
6.5"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
21-1/8 (536)
102
172672LF
618T
1-1/2x1-1/2x7
2
7"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10-3/4 (273)
23-3/8 (543)
115
172763LF
624T
2x2x7
1
5.69"
7-7/8 (200)
-
7-7/8 (200)
4-3/8 (111)
9-3/4 (248)
23-7/8 (606)
95
172764LF
625T
2x2x7
1-1/2
6.12"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10 (254)
21-3/8 (543)
108
172754LF
619T
2x2x7
2
6.5"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
10 (254)
21-3/8 (543)
118
172673LF
620T
2x2x7
3
7"
6-1/2 (165)
-
6-1/2 (165)
3-1/4 (83)
11-3/8 (289)
22-1/4 (565)
131
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.xyleminc.com/brands/bellgossett
Distribuidor: (55) 5370-9692 5305-9179 5378-7190 6731-0616 http://circuladoresbyg.com
PART #