WaveRunner
VX110 Sport VX110 Deluxe
SERVICE MANUAL *LIT186160291* LIT-18616-02-91
F1K-28197-1H-11
E
NOTICE This manual has been prepared by Yamaha primarily for use by Yamaha dealers and their trained mechanics when performing maintenance procedures and repairs to Yamaha equipment. It has been written to suit the needs of persons who have a basic understanding of the mechanical and electrical concepts and procedures inherent in the work, for without such knowledge attempted repairs or service to the equipment could render it unsafe or unfit for use. Because Yamaha has a policy of continuously improving its products, models may differ in detail from the descriptions and illustrations given in this publication. Use only the latest edition of this manual. Authorized Yamaha dealers are notified periodically of modifications and significant changes in specifications and procedures, and these are incorporated in successive editions of this manual.
A10001-0*
WaveRunner VX110 Sport, VX110 Deluxe SERVICE MANUAL Š2005 by Yamaha Motor Corporation, USA 1st Edition, January 2005 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, USA is expressly prohibited. Printed in USA LIT-18616-02-91
E
HOW TO USE THIS MANUAL MANUAL FORMAT All of the procedures in this manual are organized in a sequential, step-by-step format. The information has been compiled to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and inspection operations. In this revised format, the condition of a faulty component will precede an arrow symbol and the course of action required will follow the symbol, e.g., • Bearings Pitting/scratches → Replace. To assist you in finding your way through this manual, the section title and major heading is given at the top of every page.
ILLUSTRATIONS The illustrations within this service manual represent all of the designated models.
CROSS REFERENCES The cross references have been kept to a minimum. Cross references will direct you to the appropriate section or chapter.
E
IMPORTANT INFORMATION In this Service Manual particularly important information is distinguished in the following ways. The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
WARNING Failure to follow WARNING instructions could result in severe injury or death to the machine operator, passenger(s), a bystander, or a person inspecting or repairing the watercraft.
CAUTION: A CAUTION indicates special precautions that must be taken to avoid damage to the watercraft. NOTE: A NOTE provides key information to make procedures easier or clearer. IMPORTANT: This part has been subjected to change of specification during production.
E
HOW TO USE THIS MANUAL 1 To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section. 2 Numbers are given in the order of the jobs in the exploded diagram. 3 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”). 4 A job instruction chart accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc. 5 Dimension figures and the number of parts, are provided for fasteners that require a tightening torque. Example: Bolt or screw size
10 × 25 mm
: M10 (D) × 25 mm (L) D L
6 Jobs requiring more information (such as special tools and technical data) are described sequentially.
E 1
A50001-1-4
2
GEN INFO
SYMBOLS Symbols 1 to 9 are designed to indicate the content of a chapter.
SPEC
3
1 2 3 4 5 6 7 8 9
4
INSP ADJ
FUEL
5
6
JET PUMP
POWR 7
General Information Specifications Periodic Inspection and Adjustment Fuel System Power Unit Jet Pump Unit Electrical System Hull and Hood Trouble Analysis
8 –
ELEC 9
+
HULL HOOD Symbols 0 to E indicate specific data.
0
0 A B C D E
TRBL ANLS A
B
C
D
Special service tool Specified oil or fluid Specified engine speed Specified tightening torque Specified measurement Specified electrical value (resistance, voltage, electric current)
T.
R.
E
Symbols F to I in an exploded diagram indicate the grade of lubricant and the lubrication point.
F
E G
H A
I
1104J
1280B
J M
K
GM
L LT
LT
271
242
M
N LT
572
SS
F Apply Yamaha 4-stroke motor oil G Apply water resistant grease (Yamaha grease A, Yamaha marine grease) H Apply ThreeBond 1104J or ThreeBond 1280B I Apply molybdenum disulfide grease
Symbols J to N in an exploded diagram indicate the type of sealant or locking agent and the application point. J K L M N
Apply Gasket Maker Apply LOCTITE 271 (red) Apply LOCTITE 242 (blue) Apply LOCTITE 572 Apply silicone sealant
NOTE: Additional symbols may be used in this manual.
E A30000-0
INDEX
GENERAL INFORMATION SPECIFICATIONS PERIODIC INSPECTION AND ADJUSTMENT FUEL SYSTEM POWER UNIT JET PUMP UNIT
GEN INFO
SPEC
INSP ADJ
FUEL
POWR
JET PUMP –
ELECTRICAL SYSTEM HULL AND HOOD TROUBLE ANALYSIS
+
ELEC
HULL HOOD
TRBL ANLS
1 2 3 4 5 6 7 8 9
GEN INFO
E
CHAPTER 1 GENERAL INFORMATION IDENTIFICATION NUMBERS ......................................................................... 1-1 PRIMARY l.D. NUMBER ...........................................................................1-1 ENGINE SERIAL NUMBER ...................................................................... 1-1 JET PUMP UNIT SERIAL NUMBER .........................................................1-1 HULL IDENTIFICATION NUMBER (H.l.N.)............................................... 1-1 SAFETY WHILE WORKING...................................................................... 1-2 FIRE PREVENTION .................................................................................. 1-2 VENTILATION ........................................................................................... 1-2 SELF-PROTECTION................................................................................. 1-2 PARTS, LUBRICANTS, AND SEALANTS ................................................ 1-2 GOOD WORKING PRACTICES ............................................................... 1-3 DISASSEMBLY AND ASSEMBLY ............................................................ 1-4 SPECIAL SERVICE TOOLS ...........................................................................1-5 MEASURING............................................................................................. 1-5 REMOVAL AND INSTALLATION.............................................................. 1-7
1 2 3 4 5 6 7 8 9
GEN INFO
IDENTIFICATION NUMBERS
E
A60700-0*
IDENTIFICATION NUMBERS PRIMARY l.D. NUMBER The primary l.D. number is stamped on a label attached to the inside of the engine compartment. Starting primary l.D. number: F1K: 800101
ENGINE SERIAL NUMBER The engine serial number is stamped on a label attached to the engine unit. Starting serial number: 6D3: 1000001
JET PUMP UNIT SERIAL NUMBER The jet pump unit serial number is stamped on a label attached to the intermediate housing.
HULL IDENTIFICATION NUMBER (H.l.N.) The H.l.N. is stamped on a plate attached to the aft deck.
1-1
GEN INFO
SAFETY WHILE WORKING
E
SAFETY WHILE WORKING To prevent and accident or injury and to ensure quality service, follow the safety procedures provided below.
FIRE PREVENTION Gasoline is highly flammable. Keep gasoline and all flammable products away from heat, sparks, and open flames.
VENTILATION Gasoline vapor and exhaust gas are heavier than air and extremely poisonous. If inhaled in large quantities they may cause loss of consciousness and death within a short time. When test running an engine indoors (e.g., in a water tank), be sure to do so where adequate ventilation can be maintained.
SELF-PROTECTION Protect your eyes by wearing safety glasses or safety goggles during all operation involving drilling and grinding, or when using an air compressor. Protect your hands and feet by wearing protective gloves or safety shoes when necessary.
PARTS, LUBRICANTS, AND SEALANTS Use only genuine Yamaha parts, lubricants, and sealants or those recommended by Yamaha, when servicing or repairing the watercraft.
1-2
GEN INFO
SAFETY WHILE WORKING
E
Under normal conditions, the lubricants mentioned in this manual should not harm or be hazardous to your skin. However, you should follow these precautions to minimize any risk when working with lubricants. 1. Maintain good standards of personal and industrial hygiene. 2. Change and wash clothing as soon as possible if soiled with lubricants. 3. Avoid contact with skin. Do not, for example, place a soiled rag in your pocket. 4. Wash hands and any other part of the body thoroughly with soap and hot water after contact with a lubricant or lubricant soiled clothing has been made. 5. To protect your skin, apply a protective cream to your hands before working on the watercraft. 6. Keep a supply of clean, lint-free cloths for wiping up spills, etc.
GOOD WORKING PRACTICES 1. The right tools Use the recommended special service tools to protect parts from damage. Use the right tool in the right manner—do not improvise. 2. Tightening torques Follow the tightening torque specifications provided throughout the manual. When tightening nuts, bolts, and screws, tighten the large sizes first, and tighten fasteners starting in the center and moving outward.
1-3
GEN INFO
SAFETY WHILE WORKING
E
3. Non-reusable parts Always use new gaskets, seals, O-rings, oil seals, cotter pins, circlips, etc., when installing or assembling parts.
DISASSEMBLY AND ASSEMBLY 1. Use compressed air to remove dust and dirt during disassembly. 2. Apply engine oil to the contact surfaces of moving parts during assembly.
3. Install bearings with the manufacture identification mark in the direction indication in the installation procedure. In addition, be sure to lubricate the bearings liberally. 4. Apply a thin coat of water-resistant grease to the lip and periphery of an oil seal before installation. 5. Check that moving parts operate normally after assembly.
1-4
GEN INFO
SPECIAL SERVICE TOOLS
E
SPECIAL SERVICE TOOLS Using the correct special service tools recommended by Yamaha, will aid the work and enable accurate assembly and tune-up. Improvisations and using improper tools can damage the equipment.
1 90890-06583
2
NOTE: • For U.S.A. and Canada, use part numbers starting with “J-”, “YB-”, “YM-”, “YS-”, “YU-” or “YW-”. • For other countries, use part numbers starting with “90890-”.
90890-06584
MEASURING 3
1 Dial gauge stand P/N. 90890-06583 2 Dial gauge needle P/N. 90890-06584 3 Dial gauge stand set P/N. YB-06585 90890-06585 4 Dial indicator gauge P/N. YU-03097 Dial gauge set P/N. 90890-01252 5 Pocket tester P/N. YU-03112 90890-03112 6 Digital multimeter P/N. YU-34899-A 7 Digital circuit tester P/N. 90890-03174 8 Fuel pressure gauge adapter P/N. YW-06842 90890-06842 9 Fuel pressure gauge P/N. YB-06766 90890-06786
YB-06585 90890-06585
4 YU-03097
90890-01252
5 YU-03112
6
7 90890-03174
8 YW-06842
90890-03112
9 YB-06766
YU-34899-A
90890-06842
90890-06786
1-5
GEN INFO 0 90890-06582
B YU-33223-1
SPECIAL SERVICE TOOLS A YU-03017
90890-06759
90890-03160
C YU-39991
D 90890-03172
E YM-34487
F YB-06867 (-06767)
G YB-06870 (-06770)
H YB-06848
I YB-06877 (-06777)
J YB-35956-A
90890-06754
90890-06870 (-06770)
90890-06877 (-06777)
0 Compression gauge extension P/N. 90890-06582 A Cylinder gauge set P/N. YU-03017 90890-06759 B Compression gauge P/N. YU-33223-1 90890-03160 C Peak voltage adapter P/N. YU-39991 D Peak voltage adapter B P/N. 90890-03172 E Spark checker P/N. YM-34487 Ignition tester P/N. 90890-06754 F Test harness (2 pins) P/N. New: YB-06867 Current: YB-06767 Test harness FWY-2 (2 pins) P/N. New: 90890-06867 Current: 90890-06767 G Test harness (3 pins) P/N. New: YB-06870 Current: YB-06770 Test harness SMT250-3 (3 pins) P/N. New: 90890-06870 Current: 90890-06770 H Test harness (6 pins) P/N. YB-06848 Test harness FSW-6A (6 pins) P/N. 90890-06848 I Test harness (3 pins) P/N. New: YB-06877 Current: YB-06777 Test harness HM090-3 (3 pins) P/N. New: 90890-06877 Current: 90890-06777 J Lower unit pressure/vacuum tester P/N. YB-35956-A Vacuum/pressure pump gauge set P/N. 90890-06756
90890-06867 (-06767)
90890-06848
90890-06756
1-6
E
GEN INFO
SPECIAL SERVICE TOOLS
E
K Yamaha diagnostic system P/N. 60V-85300-02-00 L Yamaha diagnostic system P/N. 60V-WS853-03
K 60V-85300-02-00
L 60V-WS853-03
REMOVAL AND INSTALLATION 1 YB-01426
90890-01426
1 Oil filter wrench P/N. YB-01426 90890-01426 2 Coupler wrench P/N. YW-06551 90890-06551 3 Sheave holder P/N. YS-01880-A 90890-01701 4 Rotor puller P/N. YM-01082 90890-01080 5 Universal magneto and rotor holder P/N. YU-01235 Rotor holder P/N. 90890-01235 6 Bearing housing needle bearing installer (reduction drive gear) P/N. YB-06111
2 YW-06551 90890-06551
3 YS-01880-A
4 YM-01082
5 YU-01235
6 YB-06111
90890-01701
90890-01235
90890-01080
1-7
GEN INFO
SPECIAL SERVICE TOOLS
7 YB-06276-B
8 90890-06657
9 YM-01253
0 YM-04114 (ø19 mm)
90890-04019
A YM-04111 (ø4.0 mm)
90890-04111 (ø4.0 mm) YM-04116 (ø4.5 mm) 90890-04116 (ø4.5 mm)
7 Forward gear bearing cup installer (reduction drive gear) P/N. YB-06276-B 8 Ball bearing attachment (reduction drive gear) P/N. 90890-06657 9 Valve spring compressor P/N. YM-01253 90890-04019 0 Valve spring compressor attachment P/N. YM-04114 (ø19 mm) 90890-04114 (ø19 mm) YM-04108 (ø22 mm) 90890-04108 (ø22 mm) A Valve guide remover P/N. YM-04111 (ø4.0 mm) 90890-04111 (ø4.0 mm) YM-04116 (ø4.5 mm) 90890-04116 (ø4.5 mm) B Valve guide installer P/N. YM-04112 (ø4.0 mm) 90890-04112 (ø4.0 mm) YM-04117 (ø4.5 mm) 90890-04117 (ø4.5 mm) C Valve guide reamer P/N. YM-04113 (ø4.0 mm) 90890-04113 (ø4.0 mm) YM-04118 (ø4.5 mm) 90890-04118 (ø4.5 mm) D Valve seat cutter Intake P/N. 90890-06813 (60°) 90890-06814 (45°) 90890-06815 (30°) Exhaust P/N. 90890-06315 (60°) 90890-06312 (45°) 90890-06328 (30°)
90890-04114 (ø19 mm) YM-04108 (ø22 mm) 90890-04108 (ø22 mm)
B YM-04112 (ø4.0 mm)
90890-04112 (ø4.0 mm) YM-04117 (ø4.5 mm) 90890-04117 (ø4.5 mm)
C YM-04113 (ø4.0 mm)
90890-04113 (ø4.0 mm) YM-04118 (ø4.5 mm) 90890-04118 (ø4.5 mm)
D 90890-06813 (60°) 90890-06814 (45°) 90890-06815 (30°)
90890-06315 (60°) 90890-06312 (45°) 90890-06328 (30°)
1-8
E
GEN INFO
SPECIAL SERVICE TOOLS
E Valve seat cutter holder P/N. 90890-06811 (ø4.0 mm) 90890-06812 (ø4.5 mm) F Neway valve seat cutter kit P/N. YM-91044 G Piston ring compressor P/N. YM-08037 90890-05158 H Drive shaft holder (impeller) P/N. YB-06151 Drive shaft holder 5 (impeller) P/N. 90890-06519 I Slide hammer and adapters (jet pump bearing and reduction drive gear) P/N. YB-06096 J Stopper guide plate (jet pump bearing) P/N. 90890-06501 K Bearing puller assembly (jet pump bearing and reduction drive gear) P/N. 90890-06535 L Stopper guide stand (jet pump bearing and reduction drive gear) P/N. 90890-06538 M Driver rod L3 (jet pump bearing and reduction drive gear) P/N. 90890-06652 N Bearing housing needle bearing remover (jet pump bearing) P/N. YB-06112 O Needle bearing attachment (jet pump bearing, oil seal, and reduction drive gear) P/N. 90890-06614, 90890-06653 Ball bearing attachment (jet pump oil seal) P/N. 90890-06634
E 90890-06811 (ø4.0 mm) F YM-91044 90890-06812 (ø4.5 mm)
G YM-08037
90890-05158
H YB-06151
I YB-06096
J 90890-06501
K 90890-06535
L 90890-06538
M 90890-06652
N YB-06112
O 90890-06614
90890-06519
E
90890-06653 90890-06634
1-9
GEN INFO
SPECIAL SERVICE TOOLS
P YB-06085
Q 90890-06631
R YB-06071
S 90890-06606
T YB-06552
U YB-06156
90890-06552
E
P Outer race installer—forward gear (jet pump oil seal and reduction drive gear) P/N. YB-06085 Q Ball bearing attachment (jet pump oil seal and reduction drive gear) P/N. 90890-06631 R Driver handle—large (intermediate shaft, jet pump, and reduction drive gear) P/N. YB-06071 S Driver rod LS (intermediate shaft, jet pump, and reduction drive gear) P/N. 90890-06606 T Crankshaft holder (intermediate shaft) P/N. YB-06552 Crankshaft holder 20 (intermediate shaft) P/N. 90890-06552 U Bearing outer race attachment (intermediate shaft and reduction drive gear) P/N. 90890-06624, 90890-06628 V Roller bearing installer/remover (intermediate shaft bearing and oil seals) P/N. YB-06432
90890-06624 90890-06626
V YB-06432
1-10
SPEC
E
CHAPTER 2 SPECIFICATIONS GENERAL SPECIFICATIONS ....................................................................... 2-1 MAINTENANCE SPECIFICATIONS ............................................................... 2-3 ENGINE .................................................................................................... 2-3 JET PUMP UNIT ......................................................................................2-6 HULL AND HOOD .................................................................................... 2-6 ELECTRICAL ............................................................................................ 2-7 TIGHTENING TORQUES .............................................................................. 2-10 SPECIFIED TORQUES...........................................................................2-10 GENERAL TORQUE ............................................................................... 2-15 CABLE AND HOSE ROUTING ..................................................................... 2-16
1 2 3 4 5 6 7 8 9
SPEC
GENERAL SPECIFICATIONS
E
GENERAL SPECIFICATIONS Item Model code Hull Engine/jet Dimensions Length Width Height Dry weight Maximum capacity Performance Maximum output Maximum fuel consumption Cruising range Engine Engine type Displacement Bore × stroke Compression ratio Exhaust system Lubrication system Cooling system Starting system Ignition system Ignition timing Spark plug model (manufacturer) Spark plug gap Battery capacity Generator output Drive unit Propulsion system Jet pump type Impeller rotation Transmission Jet thrust nozzle horizontal angle Jet thrust nozzle trim angle Reverse system
Model
Unit
VX110 Sport
VX110 Deluxe F1K 6D3
mm (in) mm (in) mm (in) kg (lb) Person/kg (lb)
3,220 (126.8) 1,170 (46.1) 1,150 (45.3) 325 (716) 3/240 (530)
kW (PS) @ r/min l/h (US gal/h, lmp gal/h) h
81.0 (110) @ 8,000 28.0 (7.4, 6.2)
3
cm (cu. in) mm (in)
Degree
2.1 4-stroke, L4, DOHC 1,052 (64.2) 76.0 × 58.0 (2.99 × 2.28) 11.4:1 Wet exhaust Dry sump Water cooled Electric starter TCI BTDC 5–BTDC 35 CR9EB (NGK)
mm (in) V/Ah A @ r/min
0.7–0.8 (0.028–0.031) 12/19 12–21 @ 6,000
Degree
Jet pump Axial flow, single stage Counterclockwise (viewed from rear) Constant mesh 1-speed 24 + 24
Degree
3 —
2-1
Reverse gate
SPEC
GENERAL SPECIFICATIONS Item
Fuel and oil Fuel type Minimum fuel rating Fuel tank capacity Engine oil type Engine oil grade Engine oil quantity (without oil filter replacement) (with oil filter replacement)
E Model
Unit
VX110 Sport
PON* RON* L (US gal, Imp gal) API SAE L (US qt, Imp qt) L (US qt, Imp qt) L (US qt, Imp qt)
VX110 Deluxe
Regular unleaded gasoline 86 90 60 (15.9, 13.2) 4-stroke motor oil SE, SF, SG, SH, SJ, SL 10W-30, 20W-40, 20W-50 4.3 (4.5, 3.8) 2.0 (2.1, 1.8) 2.2 (2.3, 1.9)
PON*: Pump Octane Number = (Motor Octane Number + Research Octane Number)/2 RON*: Research Octane Number
2-2
SPEC
MAINTENANCE SPECIFICATIONS
E
MAINTENANCE SPECIFICATIONS ENGINE Item Cylinder head Warpage limit
Compression pressure*1 Cylinder Bore size Taper limit Out-of-round limit Wear limit Camshaft Drive system Intake A Exhaust A Intake and exhaust B Camshaft cap inside diameter Camshaft journal diameter Intake Exhaust Camshaft-journal-to-camshaftcap clearance Maximum camshaft runout Timing chain Model/number of links Tensioning system Valves, valve seats, valve guides Valve clearance (cold) Intake Exhaust Valve dimensions Valve head diameter A Intake Exhaust
Model
Unit
VX110 Sport
VX110 Deluxe
mm (in)
0.1 (0.004)
kPa (kgf/cm2, psi)
1,150 (11.5, 164)
mm (in) mm (in) mm (in) mm (in)
76.000–76.015 (2.9921–2.9927) 0.08 (0.003) 0.05 (0.002) 76.100 (2.9961)
mm (in) mm (in) mm (in) mm (in)
Chain drive 31.15 (1.226) 30.75 (1.211) 25.00 (0.984) 24.5 (0.9646)
mm (in) mm (in) mm (in)
24.46–24.47 (0.9630–0.9634) 24.44–24.45 (0.9622–0.9626) 0.05–0.06 (0.0020–0.0024)
mm (in)
0.03 (0.0012) 92RH2015-130/130 Automatic
mm (in) mm (in)
0.11–0.20 (0.0043–0.0079) 0.25–0.34 (0.0098–0.0134)
mm (in) mm (in)
22.9–23.1 (0.9016–0.9094) 24.4–24.6 (0.9606–0.9685)
*1 Measuring conditions: Ambient temperature 20 °C (68 °F), wide open throttle, with spark plugs removed from all cylinders. The figures are for reference only.
2-3
SPEC
MAINTENANCE SPECIFICATIONS Item
Valve face width B Intake Exhaust Valve seat width C Intake Exhaust Valve margin thickness D Intake Exhaust Valve stem diameter Intake Exhaust Valve guide inside diameter Intake Exhaust Valve-stem-to-valve-guide clearance Intake Exhaust Valve stem runout
E Model
Unit
VX110 Sport
VX110 Deluxe
mm (in) mm (in)
1.91–2.64 (0.0752–0.1039) 1.91–2.64 (0.0752–0.1039)
mm (in) mm (in)
0.90–1.10 (0.0354–0.0433) 0.90–1.10 (0.0354–0.0433)
mm (in) mm (in)
0.85–1.15 (0.0335–0.0453) 0.85–1.15 (0.0335–0.0453)
mm (in) mm (in)
3.975–3.990 (0.1565–0.1571) 4.465–4.480 (0.1758–0.1764)
mm (in) mm (in)
4.000–4.012 (0.1575–0.1580) 4.500–4.512 (0.1772–0.1776)
mm (in) mm (in) mm (in)
0.010–0.037 (0.0004–0.0015) 0.020–0.047 (0.0008–0.0019) 0.01 (0.0004)
Valve spring Free length Intake mm (in) Exhaust mm (in) Installed length Intake mm (in) Exhaust mm (in) Tilt limit Intake Degree/mm (in) Exhaust Degree/mm (in) Piston Piston-to-cylinder clearance mm (in) Piston diameter mm (in) Measuring point H* mm (in) Wear limit mm (in) Piston pin boss inside diameter mm (in)
2-4
38.90 (1.53) 40.67 (1.60) 34.50 (1.36) 35.00 (1.38) 2.5/1.7 (0.067) 2.5/1.8 (0.071) 0.10–0.11 (0.0039–0.0043) 75.895–75.910 (2.9880–2.9886) 5 (0.2) 0.170 (0.0067) 17.002–17.013 (0.6694–0.6698)
SPEC
MAINTENANCE SPECIFICATIONS Item
B
B
Model
Unit
Piston pins Outside diameter Wear limit Piston ring Top ring T Type Dimension (B × T) End gap (installed) Ring groove clearance 2nd ring Type T Dimensions (B × T) End gap (installed) Ring groove clearance Oil ring Dimensions T (B × T) End gap (installed) Ring groove clearance Connecting rod Big end oil clearance Bearing color code Small end inside diameter Crankshaft
E
VX110 Sport
VX110 Deluxe
mm (in) mm (in)
16.991–17.000 (0.6689–0.6693) 16.986 (0.6687)
mm (in) mm (in) mm (in)
Barrel 0.90 × 2.75 (0.04 × 0.11) 0.32–0.44 (0.0126–0.0173) 0.030–0.065 (0.0012–0.0026)
mm (in) mm (in) mm (in)
Taper 0.80 × 2.80 (0.03 × 0.11) 0.43–0.58 (0.0169–0.0228) 0.020–0.055 (0.0008–0.0022)
mm (in)
1.50 × 2.60 (0.06 × 0.10)
mm (in) mm (in)
0.10–0.35 (0.0039–0.0138) 0.040–0.160 (0.0016–0.0063)
mm (in)
0.016–0.040 (0.0006–0.0016) 1. Brown 2. Black 3. Blue 4. Green 17.005–17.018 (0.6695–0.6700)
B
B
B
mm (in)
B
A
Crank width A Deflection limit B Crankshaft journal oil clearance Bearing color code Throttle body Type/quantity Manufacturer ID mark Trolling speed
mm (in) mm (in) mm (in)
304.8–306.0 (12.00–12.05) 0.03 (0.0012) 0.004–0.028 (0.0002–0.0011) 3. Red/Red 4. Red/Brown 5. Red/Black 6. Red/Blue 7. Red/Green IM-230/1 Mikuni 6D300 1,550–1,750
r/min
2-5
SPEC
MAINTENANCE SPECIFICATIONS Item
Fuel pump Pump type Fuel pressure Oil filter Oil filter type Oil pump Oil pump type Rotor tip clearance (scavenge pump) Oil pump housing clearance Rotor (feed pump) Rotor (scavenge pump)
E Model
Unit
VX110 Sport
kPa (kgf/cm2, psi)
VX110 Deluxe
Electrical 320–327 (3.2–3.3, 46–47)
Cartridge type
mm (in)
Trochoid 0.09–0.15 (0.0035–0.0059)
mm (in) mm (in)
0.09–0.17 (0.0035–0.0067) 0.09–0.15 (0.0035–0.0059)
JET PUMP UNIT Item Jet pump Impeller material Number of impeller blades Impeller pitch angle Impeller clearance Impeller clearance limit Drive shaft runout limit
Model
Unit
VX110 Sport
VX110 Deluxe
Stainless steel 3 21.2 0.35–0.45 (0.0138–0.0177) 0.6 (0.0236) 0.3 (0.0118)
Degree mm (in) mm (in) mm (in)
HULL AND HOOD Item Free play Throttle lever free play
Model
Unit
VX110 Sport
mm (in)
VX110 Deluxe
4–7 (0.16–0.28)
2-6
SPEC
MAINTENANCE SPECIFICATIONS
E
ELECTRICAL Item Battery Type Capacity Specific gravity ECM unit (B/R – R/Y, B/W – R/Y, B/Y – R/Y, B/G – R/Y) Output peak voltage lower limit @cranking (loaded) @2,000 r/min (loaded) @3,500 r/min (loaded) Stator Pickup coil (W/B – B/O) Output peak voltage @cranking (unloaded) @cranking (loaded) @2,000 r/min (loaded) @3,500 r/min (loaded) Lighting coil (G – G) Output peak voltage @cranking (unloaded) @2,000 r/min (unloaded) @3,500 r/min (unloaded) Pickup coil resistance (W/B – B/O) Lighting coil resistance (G – G) Minimum charging current Ignition coil Primary coil resistance @20 °C (68 °F) Secondary coil resistance @20 °C (68 °F) Rectifier/regulator (R – B) Output peak voltage @3,500 r/min (unloaded)
Model
Unit
VX110 Sport
VX110 Deluxe
V/Ah
Fluid 12/19 1.28
V V V
90 130 140
V V V V
8.0 6.9 19.4 25.1
V V V Ω (color)
7.8 24.5 41.6 459–561
Ω (color) A @ r/min
0.23–0.29 14 @ 6,000
Ω
1.19–1.61
kΩ
8.5–11.5
V
13.0
2-7
SPEC
MAINTENANCE SPECIFICATIONS Item
Starter motor Type Output Rating Brush length Wear limit Commutator undercut Limit Commutator diameter Limit Starter relay Rating Thermoswitch ON temperature (engine) OFF temperature (engine) ON temperature (exhaust) OFF temperature (exhaust) Engine temperature sensor Engine temperature sensor resistance (B/Y – B/Y) @ 20 °C (68 °F) @ 100 °C (212 °F) Speed sensor Output voltage (on pulse) Output pulse/one full turn Throttle position sensor Output voltage @ throttle valve fully closed Sensor 1 @ throttle valve fully opened Sensor 2 Accelerator position sensor Output voltage @ throttle lever fully closed Sensor 1 Sensor 2 @ throttle lever fully opened Sensor 1 Sensor 2
E Model
Unit
VX110 Sport
VX110 Deluxe
kW Seconds mm (in) mm (in) mm (in) mm (in) mm (in) mm (in)
Constant mesh 0.8 30 12.5 (0.49) 6.5 (0.26) 0.7 (0.03) 0.2 (0.01) 28.0 (1.10) 27.0 (1.06)
Seconds
30
°C (°F) °C (°F) °C (°F) °C (°F)
84–90 (183–194) 70–84 (158–183) 80–86 (176–187) 66–80 (151–176)
kΩ kΩ
54.2–69.0 3.12–3.48
V
11.6 2
V
0.45–0.95
V
4.60–4.70
V V
0.50–0.90 0.35–1.05
V V
3.75–4.35 3.50–4.50
2-8
SPEC
MAINTENANCE SPECIFICATIONS Item
Accelerator position sensor resistance*1 @ throttle lever fully closed Sensor 1 Sensor 2 @ throttle lever fully opened Sensor 1 Sensor 2 Cam position sensor Output voltage (G/O – B/O) Position A Position B Position C Fuel sender Fuel sender resistance Position A Position B Oil pressure switch Oil pressure switch continuity pressure Fuel injector Fuel injector resistance*1 @ 20 °C (68 °F) Fuse Rating Main Main and fuel pump relay Main and fuel pump relay Electronic control throttle valve relay Remote control unit (Deluxe model only)
E Model
Unit
VX110 Sport
VX110 Deluxe
kΩ kΩ
0.50–0.90 0.35–10.50
kΩ kΩ
3.75–4.35 3.60–4.50
V V V
More than 4.8 Less than 0.8 More than 4.8
Ω Ω
133.5–136.5 5–7
kPa (kgf/cm2, psi)
128 (1.28, 18.2)–167 (1.67, 23.8)
Ω
11.5–12.5
V/A V/A V/A V/A
12/30 12/20 12/10 12/10
V/A
12/3
*1: The figures are for reference only.
2-9
SPEC
TIGHTENING TORQUES
E
TIGHTENING TORQUES SPECIFIED TORQUES
M8 — M6 M6
4 1 1 2
—
—
2
—
—
2
Bolt
M10
4
Bolt
M6
3
Bolt
M8
4
Bolt
M8
11
17 17 7.8 7.6 3.4 3.4 3.4 3.4 2.0 15 39 3.7 7.6 22 22 35 22 22 35
1.7 1.7 0.78 0.76 0.34 0.34 0.34 0.34 0.2 1.5 3.9 0.37 0.76 2.2 2.2 3.5 2.2 2.2 3.5
12 12 5.6 5.5 2.5 2.5 2.5 2.5 1.4 11 28 2.7 5.5 16 16 25 16 16 25
*1: For details, refer to the tightening procedures in this manual.
2-10
LT
Bolt — Bolt Bolt
572
2 2
LT
M8 M5
242
Bolt Screw
LT
2
271
M8
4-7 4-10 4-10
LT
Bolt
4-7
271
2
E
M6
LT
Bolt
4-7 4-7 4-7 4-7 4-7 4-7 4-10
572
M8 — — — — M8
LT
Bolt Nut — Nut Nut Bolt
4-1 4-1
572
M5
4-1
5-1 3-17 5-1 5-8 5-8 5-8
LT
Screw
1 2 2 4 4 4 1 1 2 4
2.3 4.6 4.3 2.7 0.9 1.1 12 11 1.8 4.7 12 9.4 6.4 13 11 28 9.4 2.5
242
1st 2nd 1st Inner exhaust joint clamp 2nd 1st *1 2nd Exhaust pipe 2 3rd 1st Exhaust pipe end 2nd 1st Exhaust pipe 1 2nd 3rd 1st Exhaust manifold 2nd 3rd
— —
0.32 0.64 0.59 0.37 0.12 0.15 1.7 1.5 0.25 0.65 1.7 1.3 0.88 1.8 1.5 3.9 1.3 0.35
LT
Intake manifold bracket/ wiring harness bracket 1 Fuel rail Sensor assembly Engine Engine unit Oil filter Coupling cover Thermoswitch (exhaust) Outer exhaust joint clamp
1st 2nd 1st 2nd
Nut —
3.2 6.4 5.9 3.7 1.2 1.5 17 15 2.5 6.5 17 13 8.8 18 15 39 13 3.5
Refer to page
5-9
572
Intake manifold
9
LT
Air filter case Air filter case bracket Air intake hose clamp Throttle cable Accelerator position sensor Throttle body assembly
—
Remarks
5-10
242
Air filter case cover
Nut
Tightening torque N•m kgf•m ft•lb
LT
Fuel system 1st Retainer/fuel pump module 2nd Fuel filler neck/rubber seal Fuel filter hose clamp
Thread Q’ty size
5-10
242
Part name
Part to tightened
5-11
TIGHTENING TORQUES
Drain plug (engine oil) Strainer
1st 2nd
Drive coupling Reduction drive gear case
1st 2nd 1st 2nd
Starter motor lead Starter motor Generator cover Flywheel magneto Starter clutch
1st 2nd
M5
9
Bolt
M5
3
Bolt
M6
2
Bolt
M6
24
Screw
M4 M6
1 6
M8
4
Bolt
M8
1
Bolt
M6
2
—
—
1
Bolt
M6
2
Bolt
M8
5
Nut Bolt
— M8
1 2
Bolt
M10
8
Bolt Bolt
M10 M8
1 6
Bolt
2-11
LT
Bolt
572
8
LT
M6
572
Bolt
LT
2
572
M6
LT
Bolt
572
2
LT
M10
5-12
572
Bolt
5-12
LT
2
5-15
572
1st 2nd
—
5-15
E
Oil pump assembly
Nut
5-12
5-15
E
Anode
1
5-15
E
Oil cooler cover
M6
LT
Oil strainer
Bolt
5-12
5-15
572
Baffle plate
5
5-15
E
Oil breather plate
M10
LT
Oil tank cover
Bolt
5-12
5-15
572
Bracket (coupling cover)
3
5-21 5-21 5-21
LT
Oil tank stay
M6
5-12
572
Oil tank
Bolt
LT
Plastic tie/collar
1st 2nd 1st 2nd 1st 2nd 3rd 1st 2nd 3rd 1st 2nd 1st 2nd 1st 2nd 1st 2nd 1st 2nd 1st 2nd
2
Refer to page
5-24
572
Oil tank
M6
LT
Ground lead box
Bolt
Remarks
5-24
572
1st 2nd
Tightening torque N•m kgf•m ft•lb 3.7 0.37 2.7 7.6 0.76 5.5 7.6 0.76 5.5 15 1.5 11 39 3.9 28 3.7 0.37 2.7 7.6 0.76 5.5 2.0 0.2 1.4 15 1.5 11 39 3.9 28 2.0 0.2 1.4 15 1.5 11 39 3.9 28 3.7 0.37 2.7 7.6 0.76 5.5 3.7 0.37 2.7 7.6 0.76 5.5 1.9 0.19 1.4 4.4 0.44 3.2 1.9 0.19 1.4 4.4 0.44 3.2 3.7 0.37 2.7 7.6 0.76 5.5 3.7 0.37 2.7 7.6 0.76 5.5 3.8 0.38 2.7 10 1.0 7.2 15 1.5 11 28 2.8 20 13 1.3 9.4 3.7 0.37 2.7 7.6 0.76 5.5 28 2.8 20 3.7 0.37 2.7 7.6 0.76 5.5 15 1.5 11 28 2.8 20 4.9 0.49 3.5 18 1.8 13 15 1.5 11 50 5.0 36 75 7.5 54 24 2.4 17
5-24 5-33 5-33
A
LT
Oil separator
Thread Q’ty size
572
Part name
Part to tightened
E
E
SPEC
5-33 5-33 5-33
TIGHTENING TORQUES
Nut
—
5
— Bolt —
1 2 1
Anode cover
Bolt
Oil pan
Bolt Bolt
— M6 — M6 M8 M6 M6
15 10
Bolt
M9
10
Bolt —
M6 —
1 1
Nut
—
8
Lower crankcase
Oil pipe Oil filter bolt Connecting rod cap
1st 2nd
1
*1: For details, refer to the tightening procedures in this manual.
2-12
LT
242
LT
242 242
LT LT
242
LT
572
LT
572
5-54 5-54 5-71 5-71 5-71
E
3
E
—
E
Nut
5-54
E
2
E
—
E
Nut
5-41 5-43 5-43 5-43 5-43 5-43 5-43 5-54
E
6 1 2 10 18 2 2 3
E
M6 M6 M6 M6 M6 M7 M7 M6
E
Bolt Bolt Bolt Bolt Bolt Bolt Bolt Bolt
5-41
LT
1
5-36 5-36 5-36 5-41 5-41 5-41
572
M6
0.49 3.5 1.4 10 1.4 10 1.3 9.4 0.76 5.5 1.0 7.2 0.37 2.7 0.76 5.5 1.2 8.7 1.0 7.2 1.0 7.2 1.0 7.2 1.0 7.2 2.4 17 2.4 17 1.0 7.2 2.0 14 140 ± 5° 20 2.0 14 121 ± 5° 20 2.0 14 105 ± 5° 15 1.5 11 7.6 0.76 5.5 8.4 0.84 6.1 12 1.2 8.7 20 2.0 14 12 1.2 8.7 12 1.2 8.7 7.8 0.78 5.6 Loosen completely 15 1.5 11 ± 49 5° 12 1.2 8.7 35 3.5 25 20 2.0 14 120 ± 5°
LT
Bolt
4.9 14 14 13 7.6 10 3.7 7.6 12 10 10 10 10 24 24 10 20
572
2 2 3 4 4 1
5-36
LT
M5 M6 M6 — M6 M6
3.5
Refer to page
271
Bolt Bolt Bolt — Bolt Bolt
0.49
LT
4.9
572
1
LT
M5
Remarks
572
Bolt
1st 2nd Cylinder head*1 1st 2nd 1st 2nd Engine temperature sensor Thermoswitch (engine) Oil pressure switch
1st 2nd 3rd 4th
Tightening torque N•m kgf•m ft•lb
M
5-71 5-71 5-71
E
Washer/pickup coil lead and lighting coil lead Pickup coil Holder (wiring harness) Lighting coil Spark plug Ignition coil Cam position sensor 1st Cooling water pipe 2nd Cylinder head cover Timing chain tensioner cap bolt Timing chain tensioner Exhaust camshaft cap Intake camshaft cap Exhaust camshaft sprocket Intake camshaft sprocket
Thread Q’ty size
5-71
E
Part name
Part to tightened
E
5-74 5-74
E
SPEC
5-80
SPEC
TIGHTENING TORQUES
Part to tightened
Part name
Jet pump unit Steering cable joint Ride plate
Nut Bolt
Intake grate
Bolt
Thread Q’ty size
Tightening torque N•m kgf•m ft•lb
Reverse gate Reverse gate ball joint Reverse gate spring
Bolt Nut Nut
M8 — —
—
—
Bolt Bolt
M8 M10
2 1 1 1 1 2 4
17 14 15 7.8 7.8 1.2 2.2 15 40
Bolt
M6
4
6.6
0.66
4.8
Bolt Impeller Nut Bolt Driven coupling —
M6 M22 — M8
3 1 4 4
7.8 75 26 17
0.78 7.5 2.6 1.7
5.6 54 19 12
M24
1
36
3.6
26
—
2
4.2
0.42
3.0
6-18
4 2 4 4 2 2 2 4 1 1 4 3
20 1.1 1.1 3.7 3.4 3.4 1.2 17 6.9 20 16 16
2.0 0.11 0.11 0.37 0.34 0.34 0.12 1.7 0.69 2.0 1.6 1.6
14 0.8 0.8 2.7 2.5 2.5 0.9 12 5.0 14 12 12
8-1
Screw Screw Screw Bolt Bolt Ball joint Bolt Bolt Bolt
M8 M4 M5 M6 M5 M5 M5 M8 — M8 M8 M8
Bolt
M6
2
6.9
0.69
5.0
Nut
—
1
5.9
0.59
4.3
2-13
6-3
LT
LT
LT
6-1
LT LT
572
LT
572
LT
6-8 6-8 6-15 6-18 6-19
LT
242 242
LT LT LT LT
572
LT
572
6-6
271
LT
271
LT
572
6-5 6-5 6-5 6-5 6-3 6-6 6-6
271
6-3
572
271
6-3
8-23
LT
242 572
LT
LT
242
LT
8-1 8-4 8-4 8-4 8-20 8-20 8-20 8-21 8-21
271
LT
572
LT
572
8-1
LT
Lower handlebar cover Throttle lever assembly Handlebar switch assembly Grip end Steering column Steering cable ball joint Steering arm Steering sensor Spacer Shift cable holder (Deluxe model only) Shift cable seal (Deluxe model only)
Screw
12 10 11 5.6 5.6 0.9 1.6 11 29
6-1
242
Upper handlebar cover
Bolt
1.7 1.4 1.5 0.78 0.78 0.12 0.22 1.5 4.0
LT
2
242
M8
Clamp Hull and hood Handlebar holder
4.9
LT
Bolt
Driven coupling
0.68
572
Bracket
Jet thrust nozzle Nozzle/bracket Water inlet cover/water inlet strainer Cap Impeller Transom plate Intermediate housing cover
6.8
242
Bolt Nut
6-3 6-1
242
Rubber plate
Spout hose clamp
4.9 12 5.5 29 2.7 5.6 29
572
Bolt
4 1 4 4 2
0.68 1.7 0.76 4.0 0.37 0.78 4.0
Refer to page
Jet pump unit assembly
Screw
2
6.8 17 7.6 40 3.7 7.8 40
Remarks
— M8 M6 M10 M5 M6 M10 M6 —
Speed sensor
1 4
E
8-23
TIGHTENING TORQUES
Spout Protector (bow) Bow eye Drain plug/packing Engine mount Engine damper
Tightening torque N•m kgf•m ft•lb
Remarks
Refer to page
1
3.8
0.38
2.7
Nut
—
1
6.5
0.65
4.7
8-23
Nut
—
1
6.8
0.68
4.9
8-23
Nut Bolt Nut Bolt Bolt Bolt Bolt Nut
— M6 — M6 M5 M6 M6 —
1 1 1 2 2 4 2 4
5.9 6.9 5.9 6.9 1.9 6.9 6.9 15
0.59 0.69 0.59 0.69 0.19 0.69 0.69 1.5
4.3 5.0 4.3 5.0 1.4 5.0 5.0 11
Screw
M5
2
3.7
0.37
2.7
Bolt
M5
4
3.9
0.39
2.8
Bolt
M6
1
6.9
0.69
5.0
Bolt Bolt
M6 M6
8 2
6.9 8.0
0.69 0.8
5.0 5.8
Nut
—
2
15
1.5
11
8-16
Nut Nut Nut Bolt Bolt
— — — — M6
1 4 2 1 2
4.2 6.9 15 26 6.4
0.42 0.69 1.5 2.6 0.64
3.0 5.0 11 19 4.6
8-17 8-28 8-28 8-28 8-28
Nut
—
6
5.4
0.54
3.9
8-31
— — —
— — —
2 1 2
—
2
Bolt
M8
2.7 2.7 2.7 1.7 1.7 12
Nut
—
15
1.5
11
8-36
Nut Nut Bolt Screw Bolt Bolt
— — M6 M5 M8 M6
10 2 4 1 5 2 4 8 2
0.37 0.37 0.37 0.24 0.24 1.6
8-31 8-31 8-31
—
3.7 3.7 3.7 2.4 2.4 16
5.4 6.9 13 2.0 17 6.6
0.54 0.69 1.3 0.2 1.7 0.66
3.9 5.0 9.4 1.4 12 4.8
8-36 8-36 8-36 8-36 8-38 8-38
2-14
LT LT
572
LT
LT LT
242 572
8-11 8-11 8-16
LT
LT
LT
LT
572 572
8-11
271
8-11
572
8-23 8-23 8-23 8-8 8-8 8-8 8-8 8-8
LT
LT
8-23
572
242
572
572
LT
—
572
Nut
LT
572
8-31
LT
Cleat
Thread Q’ty size
572
Shift cable locknut (Deluxe model only) Steering cable locknut (steering column side) Steering cable locknut (jet pump side) Steering cable seal Steering cable bracket Speed sensor lead grommet Hinge assembly Hood lock assembly Hinge assembly Lid lock hook Mirror (Deluxe model only) Shift handle lever (Deluxe model only) Multifunction meter Engine hatch cover (Deluxe model only) Engine hatch cover Detent plate Shift lever bracket (Deluxe model only) Pilot water outlet Hand grip Seat bracket Seat lock projection Seat lock assembly Plate/rubber hose/exhaust valve Hose clamp 1 Hose clamp 2 Joint clamp 1 and 4 1st Joint clamp 2 and 3 2nd Sponson
Part name
LT
Part to tightened
E
271
SPEC
8-36
SPEC
TIGHTENING TORQUES
Slant detection switch Rectifier/regulator Brush assembly/spacer Starter motor rear cover Remote control transmitter cover
Nut A
Bolt B
8 mm 10 mm 12 mm 14 mm 17 mm
M5 M6 M8 M10 M12
M8
2
ø6
Tapping screw Bolt Nut Bolt Tapping screw
17 15 4.0 8.8 18
1.7 1.5 0.4 0.88 1.8
12 11 2.9 6.4 13
2
3.9
0.39
2.8
7-2
M8 — M5
2 1 2
4.0 8.8 6.4
0.4 0.88 0.64
2.9 6.4 4.6
7-7 7-39 7-39
ø2
6
0.1
0.01
0.1
LT
Bolt
Refer to page
572
2 4 4
LT
— — M6
Remarks
7-2 7-2 7-7
572
1st 2nd
Bracket
Nut Nut Bolt
Tightening torque N•m kgf•m ft•lb
LT
Electrical Fuse box Fuse box bracket ECM
Thread Q’ty size
7-7
572
Part name
Part to tightened
E
7-64
GENERAL TORQUE
General torque specifications N•m kgf•m ft•lb 5.0 0.5 3.6 8.0 0.8 5.8 18 1.8 13 36 3.6 26 43 4.3 31
This chart specifies tightening torques for standard fasteners with a standard ISO thread pitch. Tightening torque specifications for special components or assemblies are provided in applicable sections of this manual. To avoid warpage, tighten multi-fastener assemblies in a crisscross fashion and progressive stages until the specified tightening torque is reached. Unless otherwise specified, tightening torque specifications require clean, dry threads. Components should be at room temperature.
2-15
SPEC
CABLE AND HOSE ROUTING
E
CABLE AND HOSE ROUTING ÈÉ
1
G
A
F K E
B J
K-K
D
K
A-A
2 3
A B
K
J
1
J
B-B C B
J-J
B
4
A C I
C-C
C
I
I-I
D
D
A
5 6
5 6 D-D
I
I
2
I
E
E
F
F
0
Ê
H-H
7
H
H
H
B G
7 6
2 E-E
8
G
7 6
A G-G
F-F 0 9
1 2 3 4 5 6 7 8 9 0 A
B C D E F G H I J K
Fuel tank breather hose Steering cable Throttle cable Fuse box Starter motor lead Positive battery lead Negative battery lead Battery Cooling water outlet hose Shift cable (Deluxe model only) Speed sensor lead 2-16
Cooling water inlet hose Fuel hose Electric fuel pump Accelerator position sensor Antenna lead (Deluxe model only) Remote control unit lead (Deluxe model only) Bilge hose joint Cooling water hose joint Cooling water pilot outlet hose Accelerator position sensor lead
SPEC
CABLE AND HOSE ROUTING
ÈÉ
E
1
G
A
F K E
B J
K-K
D
K
A-A
2 3
A B
K
J
1
J
B-B C B
J-J
B
4
A C I
C-C
C
I
I-I
D
D
A
5 6
5 6 D-D
I
I
2
I
E
E
F
F
0
Ê
H-H
7
H
H
H
B G
7 6
2 E-E
8
G
7 6
A G-G
F-F 0 9
È Fasten the speed sensor lead, fuel sender lead, wiring harness, and antenna lead (Deluxe model only) with plastic tie 1 at the white tape on the wiring harness. É Fasten the steering sensor lead, handlebar switch lead, multifunction meter lead, and buzzer lead with plastic tie 2. Ê To install the cooling water inlet hose, align the white paint mark on the hose with the parting line on the hose joint.
2-17
SPEC
CABLE AND HOSE ROUTING
12
Ï J
A
3 4
C
Ð J M
B
4
890
567 C D
E
A
H F
H-H
B C D
H
I Ó
G
HGF
E I
P Ô
0
G-G
Ð
A O
È
Ê
Q
I
Ò É
L
Õ
A
G
5
F
E
È
Ë
E
É
N
Î Í
D 1 2 3 4 5 6 7 8 9 0 A
K
P
G
Ñ
J
B C D E F G H I J K L
Multifunction meter Handlebar switch lead Buzzer Shift cable (Deluxe model only) Fuel hose Relay assembly Fuse box ECM Positive battery lead Flushing hose Cooling water outlet hose 2-18
B
Ì
Bilge hose Battery breather hose Battery Negative battery lead Starter motor lead Speed sensor lead Steering cable Remote control unit lead (Deluxe model only) Fuel tank breather hose Antenna lead (Deluxe model only) Ventilation hose
SPEC
CABLE AND HOSE ROUTING
12
Ï J
A
3 4
C
Ð J M
B
4
890
567 C D
E
A
H F
H-H
B C D
H
I Ó
G
HGF
E I
P Ô
0
G-G
Ð
A O
È
Ê
Q
I
Ò É
L
Õ
A
G
5
F
E
È
Ë
E
É
N
Î Í
D M N O P Q
K
P
G
Ñ
J
B
Ì
É Fasten the speed sensor lead, fuel sender lead, wiring harness, and antenna lead (Deluxe model only) with plastic tie 1 at the white tape on the wiring harness. Ê Deluxe model Ë Sport model Ì To remote control unit (Deluxe model only) Í Fasten the antenna lead and wiring harness with a plastic tie at the white tape. (Deluxe model only) Î To engine unit (Deluxe model only)
Water separator Electric fuel pump Oil separator breather hose (to air intake duct) Wiring harness Cooling water inlet hose
È Fasten the steering sensor lead, handlebar switch lead, multifunction meter lead, and buzzer lead with plastic tie 2.
2-19
SPEC
CABLE AND HOSE ROUTING
12
Ï J
A
3 4
C
Ð J M
B
4
890
567 C D
E
A
H F
H-H
B C D
H
I Ó
G
HGF
E I
P Ô
0
G-G
Ð
A O
È
Ê
Q
I
Ò É
L
Õ
A
G
5
F
E
K
P
G
Ñ
J
È
Ë
E
É
N
Î Í
D Ï To ventilation socket Ð To fuel tank Ñ Point the arrow on the cover toward the fuel tank. Ò Fasten the fuel hose with a plastic tie. Ó To fuse box Ô Fasten the wiring harness with a plastic tie at the white tape. Õ To ECM
2-20
B
Ì
SPEC
CABLE AND HOSE ROUTING
Ñ
E
2
Ò 2
Ê
8
2
Ó
A Ê
B C
5 6
Ì
4 Ê
ÎÏ
Í
2
7
F
É
8
Ë
3
F C
2
E E
D
A B
Ô 1
È
2
2
Ð
2 2
Õ 2
2 F-F 1 2 3 4 5 6 7 8
E-E
D
È To install the cooling water outlet hose, align the white paint mark on the cooling water hose with the projection of the hose joint. É To transom plate Ê Fasten the cooling water outlet hose with a plastic tie. Ë 25–45 mm (0.98–1.77 in) Ì Fasten the oil separator breather (to oil tank) hose and cooling water hose with a holder.
Cooling water inlet hose Cooling water hose Cooling water outlet hose Flushing hose Cylinder head breather hose Oil separator breather hose (to oil tank) Oil separator breather hose (to air intake duct) Cooling water pilot outlet hose
2-21
SPEC
CABLE AND HOSE ROUTING
Ñ
E
2
Ò 2
Ê
8
2
Ó
A Ê
B C
5 6
Ì
4 Ê
ÎÏ
Í
2
7
F
É
8
Ë
3
F C
2
E E
D
A B
Ô 1
È
2
2
Ð
2 2
Õ 2
2 F-F
E-E
D
Ñ Install the cooling water hose with the white paint mark facing up. Ò To cooling water pilot outlet Ó Face the ends of the hose clamp towards the bow. Ô Install the hose onto the cooling water pipe until the pipe reaches the curve in the hose. Õ Insert the plastic tie completely into the hole in the boss on the cylinder block.
Í Fasten the oil separator breather hose (to air intake duct) and cooling water hose with a holder. Î Face the ends of the hose clamp towards the starboard (right) side of the watercraft. Ï Insert the cooling water hose to the paint mark. Ð To install the cooling water hose, align the white paint mark on the cooling water hose with the arrow mark of the hose joint.
2-22
SPEC
CABLE AND HOSE ROUTING
1
3
E
4
5
6
7
È 2
É
Í D 8
E F
A-A
8
9
AB
0
A
A
C
Ê
Ë Ì
1 2 3 4 5 6 7 8 9 0 A
Î
B C D E F
Oil separator breather hose (to air intake duct) Wiring harness Ignition coil lead #1 Ignition coil lead #2 Ignition coil lead #3 Ignition coil lead #4 Cam position sensor Ignition coil ECM Rectifier/regulator Oil pressure switch coupler
Thermoswitch (exhaust) coupler Ground lead plate Wiring harness Thermoswitch (exhaust) lead Oil pressure switch lead
È Fasten the oil separator breather hose (to air intake duct) at the paint mark with a holder. É 15–25 mm (0.59–0.98 in) Ê To fuse box Ë To multifunction meter 2-23
SPEC
CABLE AND HOSE ROUTING
1
3
E
4
5
6
7
È 2
É
Í D 8
E F
A-A
9
8
AB
0
A
Ê
Ë Ì
Î
Ì To generator Í Fasten the thermoswitch (exhaust) lead at the protective sleeve, the oil pressure switch lead at the corrugated tube, and the wiring harness at the tape on the harness with a plastic tie. Î 60–80 mm (2.36–3.15 in)
2-24
A
C
SPEC
CABLE AND HOSE ROUTING
Ð
Ú
0
E
2 5
D-D
Î
Ï
6
3
4
1 A-A D
A
D
Ì Í Ì
Ù
Ë Ê
Ë A
É È
9
8 5
5 C-C
B-B Ñ
Ì
B
Ñ ÌÑ
C
Ò
Ô Ó Õ 7
B
C
Ö × Ø 1 2 3 4 5 6 7
È To engine temperature sensor É To thermoswitch (engine) Ê Route the engine thermoswitch lead and engine temperature sensor lead through the corrugated tube. Ë More than 10 mm (0.39 in) Ì Do not leave any slack in the lead. Í Attach the thermoswitch (engine) coupler to the bracket. Î Attach a joint connector to the bracket. Ï Pass the fuel injector leads under the fuel rail.
Ignition coil Fuel rail Fuel injector coupler Throttle body assembly coupler Wiring harness Engine temperature sensor lead Sensor assembly (intake air pressure and intake air temperature) 8 Cam position sensor coupler 9 Cam position sensor lead 0 Oil pressure switch 2-25
SPEC
CABLE AND HOSE ROUTING
Ð
Ú
0
E
2 5
D-D
Î
Ï
6
3
4
1 A-A D
A
D
Ì Í Ì
Ù
Ë Ê
Ë A
É È
9
8 5
5 C-C
B-B Ñ
Ì
B
Ñ ÌÑ
C
Ò
Ô Ó Õ 7
B
C
Ö × Ø Õ Pass fuel injector lead #4 under the sensor assembly (intake air pressure and intake air temperature) lead. Ö To oil pressure switch × To thermoswitch (exhaust) Ø To ground lead plate Ù Bow end Ú Make sure that the rubber boot is fitted properly without any folds.
Ð Insert the plastic tie completely into the hole in the engine hanger. Ñ Fasten the wiring harness to a bracket on the fuel rail with a plastic tie. Ò Fasten the wiring harness and cam position sensor within the range shown in the illustration with a plastic tie. Ó Split in wiring harness Ô To cam position sensor
2-26
INSP ADJ
E
CHAPTER 3 PERIODIC INSPECTION AND ADJUSTMENT MAINTENANCE INTERVAL CHART .............................................................. 3-1 PERIODIC SERVICE .......................................................................................3-2 CONTROL SYSTEM ................................................................................. 3-2 Steering column inspection .................................................................3-2 Steering cable inspection and adjustment .......................................... 3-2 Throttle cable inspection and adjustment............................................3-4 Shift cable inspection and adjustment (Deluxe model only)................ 3-5 Trolling speed inspection .................................................................... 3-6 FUEL SYSTEM.......................................................................................... 3-7 Fuel line inspection .............................................................................3-7 Water separator inspection .................................................................3-8 POWER UNIT............................................................................................ 3-8 Valve clearance adjustment ................................................................3-8 Engine oil level check........................................................................3-14 Engine oil change — using oil changer............................................. 3-16 Air filter element clean....................................................................... 3-18 Spark plug inspection........................................................................3-20 ELECTRICAL .......................................................................................... 3-22 Battery inspection.............................................................................. 3-22 JET PUMP UNIT .....................................................................................3-25 Impeller inspection ............................................................................3-25 Water inlet strainer inspection........................................................... 3-25 BILGE PUMP........................................................................................... 3-26 Bilge strainer inspection .................................................................... 3-26 GENERAL ...............................................................................................3-26 Drain plug inspection.........................................................................3-26 Lubrication points .............................................................................. 3-26
1 2 3 4 5 6 7 8 9
INSP ADJ
MAINTENANCE INTERVAL CHART
E
MAINTENANCE INTERVAL CHART The following chart should be considered strictly as a guide to general maintenance intervals. Depending on operating conditions, the intervals of maintenance should be changed. THEREAFTER PAGE EVERY 10 hours 50 hours 100 hours 100 hours 200 hours 6 12 12 24 months months months months Inspect, clean, adjust 3-20 Lubricate 3-26 Inspect 3-7 Inspect, clean 3-7 Inspect 3-6 Inspect — Flush *1 — Inspect, clean — Clean 3-26 Inspect 3-25 Inspect, adjust 3-2
MAINTENANCE INTERVAL
ITEM Spark plug Lubrication points Fuel system Fuel tank Trolling speed Throttle shaft Cooling water passages Water inlet strainer Bilge strainer Impeller Jet thrust nozzle angle Shift cable and mechanism (Deluxe model only) Throttle cable Stern drain plugs Battery Rubber coupling Engine mount Nuts and bolts Air filter Engine oil Engine oil filter Valve clearance
INITIAL
Inspect, adjust
3-5
Inspect, adjust Inspect, replace Inspect Inspect Inspect Inspect Inspect, replace Replace Replace Inspect, adjust
3-4 3-26 3-22 — 5-7 — 3-18 3-14 3-16 3-8
*1: After every use
3-1
INSP ADJ
CONTROL SYSTEM
E
PERIODIC SERVICE CONTROL SYSTEM Steering column inspection 1. Inspect: • Steering column Excessive play → Replace the steering column. Refer to “STEERING COLUMN” in Chapter 8. Inspection steps: • Move the handlebar up and down and back and forth. • Check the excessive play of the handlebar.
Steering cable inspection and adjustment 1. Inspect: • Jet thrust nozzle distances a and b Out of specification → Adjust. Difference of distances a and b: Maximum 5 mm (0.2 in) Measurement steps: • Set the control grip to the neutral position. • Turn the handlebar lock to lock. • Measure distances a and b. • If the difference of distances a and b is not within specification, adjust the cable joint.
3-2
INSP ADJ
CONTROL SYSTEM
E 2. Adjust: • Steering cable joint (steering column end) Adjustment steps: • Set the control grip to the neutral position. • Loosen the locknut 1. • Disconnect the cable joint 2 from the ball joint 3. • Turn the cable joint 2 in or out to adjust the steering cable length c.
c
Steering cable length c: 218.8 mm (8.61 in) NOTE: • Check that the sum of lengths c and d is 581.8 ± 1 mm (22.91 ± 0.04 in). • If the sum of lengths c and d is out of specification, adjust length d, and then check the jet thrust nozzle distances again.
d
WARNING The cable joint must be screwed in more than 8 mm (0.31 in). • Connect the cable joint and tighten the locknut.
T.
Locknut: 6.8 N • m (0.68 kgf • m, 4.9 ft • lb)
R.
NOTE: Adjust the cable joint at the jet pump end. Refer to “REMOTE CONTROL CABLES AND SPEED SENSOR LEAD” in Chapter 8.
3-3
INSP ADJ
CONTROL SYSTEM
E Throttle cable inspection and adjustment NOTE: Before adjusting the throttle lever free play, check the trolling speed. 1. Measure: • Throttle lever free play a Out of specification → Adjust. Throttle lever free play a: 4–7 mm (0.16–0.28 in) • Throttle cable length b Out of specification → Adjust. Throttle cable length b: 18.4 ± 1 mm (0.72 ± 0.04 in) NOTE: • Check that the throttle cable length b is 18.4 ± 1 mm (0.72 ± 0.04 in). Adjust if necessary. • Adjust the throttle lever free play at the throttle lever end of the throttle cable.
b
2. Adjust: • Throttle lever free play a Adjustment steps: a. Remove the handlebar cover. b. Loosen the locknut 1. c. Turn the adjuster 2 in or out until the specified free play is obtained. Turn in
Free play is increased.
Turn out
Free play is decreased.
d. Tighten the locknut 1. NOTE: If the throttle cable free play cannot be adjusted properly, replace the throttle cable.
3-4
INSP ADJ
CONTROL SYSTEM
E
e. Install the handlebar cover.
T.
R.
Lower handlebar cover screw: 3.7 N • m (0.37 kgf • m, 2.7 ft • lb) LOCTITE 242 Upper handlebar cover screw: 1.1 N • m (0.11 kgf • m, 0.8 ft • lb)
WARNING After adjusting the free play, turn the handlebar to the right and left and make sure that the trolling speed does not increase.
Shift cable inspection and adjustment (Deluxe model only) 1. Check: • Reverse gate stopper lever position Incorrect → Adjust. Checking steps: • Set the shift lever to the reverse position. • Check that the reverse gate 1 contacts the stopper 2. 2. Adjust: • Shift cable joint
1
Adjustment steps: • Loosen the locknut 1. • Disconnect the cable joint 2 from the ball joint 3. • Situate the reverse gate to the stopper. • Turn the cable joint in or out to align it with the ball joint.
3 2
3-5
Turn in
Length is decreased.
Turn out
Length is increased.
INSP ADJ
CONTROL SYSTEM
E
• Turn out the cable joint nine times a to extend the cable 7 mm (0.28 in) from the aligned position.
WARNING The cable joint must be screwed in more than 8 mm (0.31 in). • Connect the cable joint and tighten the locknut.
T.
Locknut: 3.8 N • m (0.38 kgf • m, 2.7 ft • lb)
R.
Trolling speed inspection 1. Inspect: • Trolling speed Trolling speed: 1,550–1,750 r/min Checking steps (watercraft in water): • Start the engine and allow it to warm up for 15 minutes. • Check the engine trolling speed using the tachometer of the multifunction meter or using the Yamaha Diagnostic System.
3-6
INSP ADJ
FUEL SYSTEM
E
FUEL SYSTEM WARNING When removing fuel system parts, wrap them in a cloth and take care that no fuel spills into the engine compartment. Fuel line inspection 1. Inspect: • Fuel pump filter Clog/contaminants → Clean. Refer to “FUEL TANK AND FUEL PUMP MODULE” in Chapter 4. • Fuel hose Cracks/damage → Replace. • O-rings (quick connector) Cracks/damage → Replace the quick connector. • Fuel rail Cracks/damage → Replace. Refer to “FUEL INJECTION SYSTEM” in Chapter 4. • Fuel filler hose • Fuel filler cap Cracks/damage → Replace.
2. Inspect: • Fuel tank Cracks/damage → Replace. Water accumulation → Remove. NOTE: • To remove water from the fuel tank, remove the fuel filler hose 1 and use a siphon pump. • Refer to “FUEL TANK AND FUEL PUMP MODULE” in Chapter 4.
1
3-7
INSP ADJ
FUEL SYSTEM/POWER UNIT
E
Water separator inspection 1. Inspect: • Water separator 1 Water accumulation → Drain. NOTE: To drain the water, remove the drain plug.
POWER UNIT Valve clearance adjustment The following procedure applies to all of the valves. NOTE: • Valve clearance adjustment should be made on a cold engine, at room temperature. • When the valve clearance is to be measured or adjusted, the piston must be at top dead center (TDC) of the compression stroke. 1. Remove: • Ignition coils • Spark plugs • Cylinder head cover • Cylinder head cover gasket Refer to “CAMSHAFTS” in Chapter 5. 2. Install: • Dial gauge needle • Dial gauge stand 1 (into spark plug hole #1) • Dial gauge 2
2
Dial gauge stand: 90890-06583 Dial gauge needle: 90890-06584 Dial gauge stand set: YB-06585/90890-06585 Dial indicator gauge: YU-03097 Dial gauge set: 90890-01252
1
3-8
INSP ADJ
POWER UNIT
E 3. Measure: • Valve clearance Out of specification → Adjust. Valve clearance (cold): Intake valve: 0.11–0.20 mm (0.0043–0.0079 in) Exhaust valve: 0.25–0.34 mm (0.0098–0.0134 in)
EX
IN
Measurement steps: • Turn the drive coupling counterclockwise, and then check if cylinder #1 is at TDC of the compression stroke with a dial gauge. NOTE: TDC of the compression stroke can be found when the camshaft lobes are turned away from each other. • Measure the valve clearance with a thickness gauge 1. NOTE: • If the valve clearance is incorrect, record the measured reading. • Measure the valve clearance in the following sequence.
1
Valve clearance measuring sequence: Cylinder #1 → #2 → #4 → #3 È Bow end
• To measure the valve clearances of the other cylinders, starting with cylinder #1 at TDC, turn the drive coupling counterclockwise as specified in the following table. É Degrees that the crankshaft is turned clockwise Ê Cylinder Ë Combustion cycle
É
0
#1
Ê
#2
180
360
540
Ë Ë Ë
#3 #4
720
Ë
3-9
Cylinder #2
180°
Cylinder #4
360°
Cylinder #3
540°
INSP ADJ
POWER UNIT
E 4. Remove: • Timing chain tensioner cap bolt 1 • Gasket
1
5. Turn the timing chain tensioner rod fully clockwise with a thin screwdriver 1. NOTE: Make sure that the tensioner rod has been fully turned clockwise.
1
6. Remove: • Intake camshaft caps • Exhaust camshaft caps • Timing chain (from the camshaft sprockets) • Intake camshaft • Exhaust camshaft NOTE: • Refer to “CAMSHAFTS” in Chapter 5. • When removing the timing chain and camshafts, fasten the timing chain with a wire to prevent it from falling into the crankcase.
3-10
Thank you very much for your reading. Please Click Here Then Get More Information.