BOBCAT S220 SKID STEER LOADER Service Repair Manual SN 523211001 & Above

Service Manual S/N 523211001 & Above S/N 523311001 & Above

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) 6902447 (3-06)

Printed in U.S.A.

© Bobcat Company 2006

MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow W-2003-0903 instructions can cause injury or death.

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

CORRECT

B-10731a

B-16261

Never service the Bobcat SkidSteer Loader without instructions.

Use the correct procedure to lift or lower operator cab.

CORRECT

B-16264

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B-16272

B-16260

B-16263

Have good ventilation when welding or grinding painted parts.

Wear dust mask when grinding painted parts. Toxic dust and gas can be produced.

Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device.

Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged.

Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

WRONG

B-16271

B-16270 B-16102

B-6589 B-16102

Stop, cool and clean engine of flammable materials before checking fluids.

Never service or adjust loader with the engine running unless instructed to do so in the manual.

Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes.

Never fill fuel tank with engine running, while smoking or when near open flame.

Keep body, jewelry and clothing away from moving parts, electrical contact, hot parts and exhaust.

Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used.

Use eye protection approved for type of welding.

Keep rear door closed except for service. Close and latch door before operating the loader.

Lead-acid batteries produce flammable and explosive gases.

Keep arcs, sparks, flames and lighted tobacco away from batteries.

Batteries contain acid which burns eyes or skin on contact.

Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer.

MSW14-0805

ALPHABETICAL INDEX ADVANCED CONTROL SYSTEM (ACS) ............... 60-01 AIR CLEANER .................................................... 70-01 AIR CLEANER SERVICE ....................................... 10-01 ALTERNATOR ........................................................ 60-01

FLYWHEEL RPM SENSOR ................................ 60-01 FRONT AUXILIARY HYD. COUPLER BLOCK .......20-01 FUEL SYSTEM........................................................10-01 FUEL TANK .............................................................50-01

BATTERY ............................................................... 60-01 BICS™ SYSTEM .................................................... 60-01 BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) ....................... 60-01 BOB-TACH .............................................. 10-01, 50-01 BRAKE .................................................................... 40-01 BRAKE (TWO-SPEED)........................................... 40-01 BUCKET POSITION VALVE ............................... 20-01 CHAINCASE ........................................................... 40-01 CHARGE PRESSURE SENDER ............................ 30-01 CONTROL HANDLE ............................................... 50-01 CONTROL HANDLE (ADVANCED CONTROL SYSTEM) (ACS) SELECTABLE HAND/FOOT CONTROL ... 50-01 CONTROL HANDLE (SELECTABLE JOYSTICK CONTROL) (SJC) ..... 50-01 CONTROL PANEL.................................................. 50-01 CONTROL PANEL (SELECTABLE JOYSTICK CONTROL) (SJC) .... 50-01 CONTROL PEDALS ............................................... 50-01 CONTROL PEDALS (ACS) .................................... 50-01 CONTROLLER (BOBCAT) ..................................... 60-01 CONTROLLER (SELECTABLE JOYSTICK CONTROL) (SJC)............................... 60-01 CONVERSIONS ............................................SPEC-01 COOLING FAN ....................................................... 70-01 CYLINDER (LIFT) ................................................... 20-01 CYLINDER (POWER BOB-TACH) ......................... 20-01 CYLINDER (TILT) ................................................ 20-01

HYDRAULIC CONNECTION SPECS ............... SPEC-01 HYDRAULIC CONTROL VALVE (ADVANCED CONTROL SYSTEM) (ACS) ...........20-01 HYDRAULIC CONTROL VALVE (FOOT CONTROL)................................................20-01 HYDRAULIC CONTROL VALVE (SELECTABLE JOYSTICK CONTROL) (SJC)......20-01 HYDRAULIC FLUID RESERVOIR ..........................20-01 HYDRAULIC/HYDROSTATIC FLUID SPECIFICATIONS .......................... SPEC-01 HYDRAULIC/HYDROSTATIC FILTER....................20-01 HYDRAULIC/HYDROSTATIC SYSTEM .................10-01 HYDRAULIC PUMP ................................................20-01 HYDRAULIC PUMP (SELECTABLE JOYSTICK CONTROL) (SJC)......20-01 HYDRAULIC PUMP (CHARGE)..............................20-01 HYDRAULIC PUMP (HI FLOW) ..............................20-01 HYDRAULIC PUMP (HI FLOW) (SELECTABLE JOYSTICK CONTROL) (SJC)......20-01 HYDRAULIC SYSTEM INFORMATION ..................20-01 HYDROSTATIC MOTOR .................................... 30-01 HYDROSTATIC MOTOR (TWO SPEED) ...............30-01 HYDROSTATIC MOTOR CARRIER .......................30-01 HYDROSTATIC MOTOR CARRIER (SELECTABLE JOYSTICK CONTROL) (SJC)......30-01 HYDROSTATIC PUMP ....................................... 30-01 HYDROSTATIC PUMP (SELECTABLE JOYSTICK CONTROL) (SJC)......30-01 HYDROSTATIC SYSTEM INFORMATION20-01, 30-01

DIAGNOSTICS SERVICE CODE ........................ 60-01 DRIVE BELT ........................................................... 30-01 DRIVE COMPONENTS .......................................... 40-01

INSIDE ACCESS PANEL (SELECTABLE JOYSTICK CONTROL) (SJC) .....50-01 INSTRUMENT PANEL ............................................60-01

ELECTRICAL/HYDRAULIC CONTROLS REFERENCE ........................................................ 60-01 ELECTRICAL/HYDRAULIC CONTROLS REFERENCE (SELECTABLE JOYSTICK CONTROL) (SJC) ................................................. 60-01 ELECTRICAL SYSTEM INFORMATION ................ 60-01 ENGINE ................................................................. 70-01 ENGINE COOLING SYSTEM ................................. 10-01 ENGINE LUBRICATION SYSTEM ......................... 10-01 ENGINE SPECIFICATIONS ..........................SPEC-01 ENGINE SPEED CONTROL .................................. 70-01 ENGINE SPEED CONTROL (SELECTABLE JOYSTICK CONTROL) (SJC) ..... 70-01

LIFT ARMS ..............................................................50-01 LIFT ARM BY-PASS CONTROL VALVE ............ 20-01 LIFT ARM SUPPORT DEVICE ........................... 10-01 LIFT AND TILT ACTUATOR CALIBRATION (SELECTABLE JOYSTICK CONTROL) (SJC)......60-01 LIFTING AND BLOCKING THE LOADER...............10-01 LIGHTS ................................................................60-01 LOADER SPECIFICATIONS (S220) ................. SPEC-01 LUBRICATING THE LOADER ................................10-01

FAN GEARBOX ...................................................... 10-01 FINAL DRIVE TRANSMISSION (CHAINCASE) ..10-01 FLYWHEEL AND HOUSING ................................70-01

MAIN RELIEF VALVE (ACS)...................................20-01 MAIN RELIEF VALVE (FOOT CONTROL) .............20-01 MAIN RELIEF VALVE (SELECTABLE JOYSTICK CONTROL) (SJC)......20-01 MUFFLER................................................................70-01

ALPHABETICAL INDEX (CONT’D) OIL COOLER (SEAL TO CONNECT) (STC).......30-01 OPERATOR CAB .........................................10-01, 50-01 OPERATOR SEAT ..................................................50-01 OPERATOR SEAT (SUSPENSION) .......................50-01 POWER BOB-TACH ................................ 10-01, 50-01 POWER BOB-TACH BLOCK (EARLY MODELS) ...20-01 POWER BOB-TACH BLOCK (LATER MODELS) ...20-01 RADIATOR ..............................................................70-01 REAR AUXILIARY DIVERTER................................20-01 REAR DOOR ...................................................... 50-01 REAR GRILL ....................................................... 50-01 RECONDITIONING THE ENGINE ..........................70-01 REMOTE START ................................................ 10-01 RPM SENSOR.........................................................70-01 SEAT BAR ...............................................................50-01 SEAT BAR SENSOR...............................................60-01 SERVICE PC (LAPTION COMPUTER)...................60-01 SERVICE SCHEDULE ............................................10-01 SPEED SENSOR (SELECTABLE JOYSTICK CONTROL) (SJC)......60-01 STARTER ................................................................60-01 TIRE MAINTENANCE .............................................10-01 TORQUE SPECIFICATIONS FOR BOLTS ... SPEC-01 TOWING THE LOADER ..........................................10-01 TRACTION LOCK....................................................60-01 TRANSPORTING THE BOBCAT LOADER ............10-01 TROUBLESHOOTING.............................................70-01

SAFETY & MAINTENANCE

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

HYDRAULIC SYSTEM

SERIAL NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X BOBCAT LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . XI SAFETY AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10-01 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01

HYDROSTATIC SYSTEM

DRIVE SYSTEM

HYDROSTATIC SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01 ELECTRICAL SYSTEM & ANALYSIS . . . . . . . . . . . . . . . . . . . . 60-01

MAIN FRAME

ELECTRICAL SYSTEM & ANALYSIS

ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01 HEATING, VENTILATION, AIR CONDITIONING . . . . . . . . . . . . 80-01

ENGINE SERVICE

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01 HVAC

SPECIFICATIONS

SPECIFICATIONS

I

S220 Bobcat Loader Service Manual

FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, Starting procedure, daily checks, etc.

A general inspection of the following items must be made after the loader has had service or repair: 1. Check that the ROPS/FOPS (Including side screens) is in good condition and is not modified.

9. The parking brake function correctly.

2. Check that ROPS mounting hardware is tightened and is Bobcat approved.

10. Enclosure door latches must open and close freely.

3. The seat belt must be correctly installed, functional and in good condition.

11. Bob-Tach wedges and linkages must function correctly and be in good condition.

4. The seat bar must be correctly adjusted, clean and lubricated.

12. Safety treads must be in good condition.

5. Check lift arm support device, replace if damaged.

13. Check for correct function of indicator lamps (Optional on some models).

6. Machine signs must be legible and in the correct location.

14. Check hydraulic fluid level, engine oil level and fuel supply.

7. Steering levers and foot pedals must return to neutral.

15. Inspect for fuel, hydraulic fluid leaks.

8. Check for correct function of the work lights

16. Lubricate the loader.

II

must

oil

or

S220 Bobcat Loader Service Manual

17. Check the condition of the battery and cables.

22. Operate the loader and check all functions.

18. Inspect the air cleaner for damage or leaks. Check the condition of the element.

23. Check for any field modification not completed.

19. Check the electrical charging system.

24. Check for correct function of the Bobcat Interlock Control System (BICS™) before the machine is returned to the customer.

20. Check tires for wear and pressure.

25. Recommend to the owner that all necessary corrections be made before the machine is returned to service.

21. Inspect for loose or broken parts or connections.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

III

S220 Bobcat Loader Service Manual

SAFETY INSTRUCTIONS

The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments:

Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

•

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

•

The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine.

Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

•

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

•

An Operator’s Handbook fastened to the operator cab. It’s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages.

See your Bobcat dealer for more information on translated versions.

•

The AEM Safety Manual delivered with the machine gives general safety information.

•

The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shoptype service and repair work.

•

The Skid-Steer Loader Operator Training Course is available through your local dealer or at www.training.bobcat.com or www.bobcat.com.

This course is intended to provide rules and practices of correct operation of the Skid-Steer Loader. The course is available in English and Spanish versions.

•

Service Safety Training Courses are available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com. They provide information for safe and correct service procedures.

•

The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0903

WARNING Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death.

W-2044-1285

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine.

I-2019-0284

SI SSL-0206 SM

V

S220 Bobcat Loader Service Manual

SAFETY INSTRUCTIONS (CONT’D) The dealer and owner/operator review the recommended uses of the product when delivered. If the owner/operator will be using the machine for a different application(s) he or she must ask the dealer for recommendations on the new use.

Call Before You Dig 1-888-258-0808 When you call, you will be directed to a location in your state/city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.)

SI SSL-0206 SM VI

S220 Bobcat Loader Service Manual

SAFETY INSTRUCTIONS (CONT’D)

•

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

•

Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Fire Prevention The machine and attachments have components that are at high temperature under normal operating conditions.

The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Figure 1

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it will increase fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential hazard.

The spark arrestor muffler is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot.

•

Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

•

The operator cab, engine compartment, and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazard and overheating.

•

Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight.

Repair or replace any damaged part.

•

Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

•

Do not use ether or starting fluids on any engine which has glow plugs. These starting aids can cause explosion and injure you or bystanders.

•

Always clean the machine, disconnect the battery, and disconnect the wiring from the controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced.

•

Stop the engine and let it cool before adding fuel. NO SMOKING!

•

Know where fire extinguishers and first aid kits are located and how to use them. Fire extinguishers are available from your Bobcat dealer [Figure 1].

SI SSL-0206 SM

VII

S220 Bobcat Loader Service Manual

SERIAL NUMBER LOCATION

Engine Serial Number

Always use the serial number of the loader when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 3

Loader Serial Number Figure 2

P-34903

The engine serial number is located on the engine block [Figure 3].

P-31226

The loader serial number plate is located on the outside of the loader frame [Figure 2].

Explanation of loader Serial Number: XXXX Model 1.-Model/ Engine Combination

XXXXX Model 2.-Production Sequence (Series)

1. The four digit Model/Engine Combination Module number identifies the model number and engine combination.

2. The five digit Production Sequence Number identifies the order which the loader is produced.

IX

S220 Bobcat Loader Service Manual

DELIVERY REPORT Figure 4

B-16315

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure 4].

X

S220 Bobcat Loader Service Manual

BOBCAT LOADER IDENTIFICATION FRONT LIGHTS

OPERATOR SEAT with SEAT BELT & SEAT BAR

GRAB HANDLES

TILT CYLINDER

FRONT AUXILIARY QUICK COUPLERS

+ BUCKET

STEPS

BUCKET STEPS

LIFT CYLINDER

● OPERATOR CAB (ROPS & FOPS) SEAT BAR LIFT ARM

REAR GRILL

LIFT ARM SUPPORT DEVICE REAR LIGHT

REAR DOOR

▼ TAIL LIGHT

* TIRES B-19816 B-19813

▼ OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) * TIRES - Flotation tires ▼ are shown. The Bobcat loader is factory equipped with standard tires. + BUCKET - Several different buckets and other attachments are available for the Bobcat loader. ● ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAEJ1043 and ISO 3449, Level I. Level II is available. The Bobcat loader is base-equipped with a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level).

XI

S220 Bobcat Loader Service Manual

SAFETY AND MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-150-1

SAFETY & MAINTENANCE

ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1 Cleaning Cooling System. . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1 ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . .

Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacing Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . .

10-110-1 10-110-1 10-110-1 10-110-1

DRIVE SYSTEM

FAN GEARBOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . 10-130-1 Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 Replacing The Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing Air From The Fuel System . . . . . . . . . . . . . . .

10-100-1 10-100-1 10-100-1 10-100-1 10-100-2

HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . .

Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic/Hydrostatic Filter Replacement . . . . . . . . . . . .

Replacing Hydraulic Fluid And Case Drain Filters . . . . . .

10-120-1 10-120-1 10-120-1 10-120-2

ELECTRICAL SYSTEM & ANALYSIS ENGINE SERVICE

SPECIFICATIONS

LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Engaging The Lift Arm Support Device . . . . . . . . . . . . . . . 10-20-1 Disengaging The Lift Arm Support Device. . . . . . . . . . . . . 10-20-2 LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LUBRICATING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lowering The Operator Cab . . . . . . . . . . . . . . . . . . . . . . .

Raising The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . .

Continued On Next Page 10-01

10-30-1 10-30-1 10-30-2 10-30-2 10-30-1 S220 Bobcat Loader Service Manual

SAFETY AND MAINTENANCE (CONT’D) POWER BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-151-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-151-1 REMOTE START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Procedure For Loader With Attachments Control Harness Procedure For Loader W/O Attachments Control Harness

10-60-1 10-60-3 10-60-2 10-60-1

SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tire Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tire Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-170-1 10-170-1 10-170-1 10-170-1

TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure For Non-Two-Speeds . . . . . . . . . . . . . . . . . . . . 10-50-1 TRANSPORTING THE BOBCAT LOADER . . . . . . . . . . . . . . 10-40-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1

10-02

S220 Bobcat Loader Service Manual

LIFTING AND BLOCKING THE LOADER

Figure 10-10-2

Procedure Figure 10-10-1

P-43747

Lift the rear of the loader and install jackstands [Figure 10-10-2].

B-7023A

Figure 10-10-3

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0199 P-43749

Read the Removal & Installation, Disassembly & Assembly, etc. completely to become familiar with the procedure before beginning [Figure 10-10-1].

Always park the loader on a level surface.

Lift the front of the loader and put jackstands under the axle tubes [Figure 10-10-3].

NOTE: Make sure the jackstands do not touch the tires.

WARNING Put jackstands under the front axles and rear corners of the frame before running the engine for service.

Failure to use jackstands can allow the machine to fall or move and cause injury or death.

W-2017-0286

10-10-1

S220 Bobcat Loader Service Manual

Figure 10-20-2

LIFT ARM SUPPORT DEVICE Engaging The Lift Arm Support Device

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

1

W-2059-0598 P-43744

WARNING Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

W-2271-1197

Lower the lift arm support device on top of the lift cylinder. Hook the free end of the spring (Item 1) [Figure 10-20-2] to the lift arm support device so there will be no interference with the suppport device engagement.

With the operator in the seat, seat belt fastend and seat bar lowered, start the engine.

Figure 10-20-1

1 2

P-43743

Maintenance and service work can be done with the lift arms lowered. If the lift arms are raised, use the folowing procedures to engage and disengage an approve lift arm support device: Install jackstands under the rear corners of the loader frame. Disconnect the spring form the lift arm support device retaining pin (Item 1) [Figure 10-20-1]. Support the lift arm support device (Item 2) [Figure 10-20-1] with your hand and remove the retaining pin.

10-20-1

S220 Bobcat Loader Service Manual

With the operator in the seat, seat belt fastened and seat bar lowered, stat the engine.

LIFT ARM SUPPORT DEVICE (CONT’D) Engaging The Lift Arm Support Device (Cont’d)

Figure 10-20-5

Figure 10-20-3

1 P-43746 P-43748

Raise the lift arms, until the lift arm support device drops onto the lift cylinder rod.

Raise the lift arms a small amount and the spring will llift the support device off the lift cylinder rod [Figure 10-205]. Lower the lift arms and stop the engine.

Lower the lift arms slowly until the lift arm support device is held between the lift arms and lift cylinder. Stop the engine. Raise the seat bar and move the pedals until both pedals lock.

Raise the seat bar and move the pedals until both pedals lock.

Install the pin (Item 1) [Figure 10-20-3] into the rear of the lift arm supoort device below the cylinder rod.

Raise the support device into the storage position and insert the pin through the lift arm support device and bracket. (See Engaging The Lift Arm Support Device on Page 10-20-1.)

Disengaging The Lift Arm Support Device Figure 10-20-4

Disconnect the spring from the bracket.

Connect the spring to the pin. (See Engaging The Lift Arm Support Device on Page 10-20-1.)

1

P-43745

Remove the pin from the lift arm support device.

Connect the spring (Item 1) [Figure 10-20-4] from the lift arm support device to the bracket below the lift arm.

10-20-2

S220 Bobcat Loader Service Manual

Figure 10-30-2

OPERATOR CAB Description The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for roll over protection.

ROPS/FOPS - Roll Over Protective Structure per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available.

Level I - Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services.

Level II - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

P-31288

P-31289

Loosen the nut (both sides) at the front corner of the operator cab [Figure 10-30-2].

Remove the nuts and plates [Figure 10-30-2] (both sides).

Raising The Operator Cab Figure 10-30-3 Figure 10-30-1

P-43750 P-43747

Always stop the engine before raising or lowering the cab.

Lift on the grab handle and bottom of the operator cab slowly until the cab is all the way up and the latching mechanism engages [Figure 10-30-3].

Stop the loader on a level surface. Lower the lift arms. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See Engaging The Lift Arm Support Device on Page 10-20-1.)

Install jackstands under the rear of the loader frame [Figure 10-30-1].

10-30-1

S220 Bobcat Loader Service Manual

Pull down on the bottom of the operator cab until it stops at the latching mechanism [Figure 10-30-4].

OPERATOR CAB (CONT'D) Raising The Operator Cab (Cont’d)

Release the latching mechanism (Inset) [Figure 10-30-4] and pull the cab all the way down.

Advanced Hand Control Only

Figure 10-30-5

P-31288

WARNING

P-31289

Install the plates and nuts [Figure 10-30-5] (both sides).

Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

Tighten the nuts to 40-50 ft.-lb. (54-68 N•m) torque.

Emergency Exit Figure 10-30-6

W-2069-1299

Lowering The Operator Cab Figure 10-30-4

N-19386

The front opening on the operator cab and rear window provide exits.

N-20120

P-43751

REAR WINDOW (If Equipped)

Always stop the engine before raising or lowering the cab.

Pull on the tag on the top of the rear window to remove the rubber cord [Figure 10-30-6].

NOTE: Make sure the seat bar is fully raised or lowered when lowering the cab. Always use the grab handles to lower the cab.

10-30-2

S220 Bobcat Loader Service Manual

Figure 10-30-9

OPERATOR CAB (CONT'D) Emergency Exit (Cont’d) Figure 10-30-7

P-28359

Push the window out with your foot [Figure 10-30-9] at any corner of the window.

P-43752

Push the rear window out of the rear of the operator cab.

Exit through the front door.

Exit through the rear of the operator cab [Figure 10-307].

Figure 10-30-8

N-20171

FRONT DOOR (If Equipped) NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit [Figure 10-30-8].

NOTE: When the special applications kit is installed, the front door cannot be used for an emergency exit.

Pull the plastic loop at the top of the window in the front door to remove the rubber cord [Figure 10-30-8].

10-30-3

S220 Bobcat Loader Service Manual

Figure 10-40-2

TRANSPORTING THE BOBCAT LOADER Procedure Figure 10-40-1

P-31228A

P-31230A

P-43631

WARNING Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [Figure 1040-1].

P-31826

6595014

W-2058-0494

Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [Figure 10-40-2].

Be sure the transport and towing vehicles are of adequate size and capacity (See Performance on Page SPEC-10-2.)

•

Lower the bucket or attachment to the floor.

•

Stop the engine.

The rear of the trailer must be blocked or supported (Item 1) [Figure 10-40-1] when loading or unloading the loader to prevent the front end of the trailer from raising up.

•

Engage the parking brake.

•

Install chains at the front and rear loader tie down positions (Inset) [Figure 10-40-2].

•

Fasten each end of the chain to the transport vehicle.

10-40-1

S220 Bobcat Loader Service Manual

Figure 10-50-2

TOWING THE LOADER Procedure For Non-Two-Speeds Figure 10-50-1

1 1 P-28038

•

Press the TRACTION LOCK OVERRIDE Button (Item 1) [Figure 10-50-2].

•

Tow the Bobcat at 2 MPH (3,2 km/hr) or less for not more than 25 feet (7,6 meters).

P-28360A

To prevent damage to the loaders hydrostatic system, the loader must be towed only a short distance at slow speed. (Example: Moving the loader onto a transport vehicle).

If the electrical system is not functioning, contact your Bobcat loader dealer.

The towing chain (or cable) must be rated at 1 & 1/2 times the weight of the loader. (See Performance on Page SPEC-10-2.)

•

Turn the key switch to RUN (Item 1) [Figure 10-50-1] (Standard Panel) OR press the RUN / ENTER Button (Deluxe).

10-50-1

S220 Bobcat Loader Service Manual

Figure 10-60-2

REMOTE START Procedure For Loader W/O Attachments Control Harness Figure 10-60-1

1

1

P-28365

Remove the cap (Item 1) [Figure 10-60-2] from the loader harness.

P13841

The tool listed will be need to do the following procedure:

When the remote start procedure is completed, replace the loader connector cap (Item 1) [Figure 10-60-2].

Figure 10-60-3

MEL1563 - Remote Start Tool Kit The remote start (Item 1) [Figure 10-60-1] is required when the operator cab is in the raised position for service and the service technician needs to turn the key switch on or start the engine. Example: adjusting the steering linkage.

2

Lift and block the loader. (See LIFTING AND BLOCKING THE LOADER on Page 10-10-1.)

1

Raise the lift arms (if required by the procedure) and install an approved lift arm support device. (See Engaging The Lift Arm Support Device on Page 10-20-1.)

P-28366

Raise the operator cab (if required by the procedure).

(See Raising The Operator Cab on Page 10-30-1.)

Open the rear door of the loader.

Connect the remote start tool to the engine harness connector (Item 1) [Figure 10-60-3].

The connector (Item 2) [Figure 10-60-3] from the remote start harness is not used in the remote start procedure and should remain capped.

NOTE: The key switch on the right-hand side operator panel must be in the off position or the Remote Start Kit will not operate.

10-60-1

S220 Bobcat Loader Service Manual

Raise the operator cab (if required by the procedure).

(See Raising The Operator Cab on Page 10-30-1.)

REMOTE START (CONT'D) Procedure For Loader W/O Attachments Control Harness (Cont’d)

Open the rear door of the loader.

Figure 10-60-5

WARNING AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and the Remote Start Key Switch in the OFF position, the loader can still be started from the operator panel inside the cab. Placing the key switch of the remote start tool in the run position disconnects the operator panel key switch from the start circuit. If the service technician will be working in the engine area it is important to remove the operator panel keys.

1

W-2357-0899 P-28362

Procedure For Loader With Attachments Control Harness Figure 10-60-6 Figure 10-60-4

1 1

2 P-28364 P13841

The tool listed will be need to do the following procedure:

Disconnect the attachment control harness (Item 1) [Figure 10-60-5] & [Figure 10-60-6] from the loader harness (Item 2) [Figure 10-60-6].

MEL1563 - Remote Start Tool Kit The remote start (Item 1) [Figure 10-60-4] is required when the operator cab is in the raised position for service and the service technician needs to turn the key switch on or start the engine. Example: adjusting the steering linkage.

Lift and block the loader. (See LIFTING AND BLOCKING THE LOADER on Page 10-10-1.)

Raise the lift arms (if required by the procedure) and install an approved lift arm support device. (See Engaging The Lift Arm Support Device on Page 10-20-1.)

10-60-2

S220 Bobcat Loader Service Manual

REMOTE START (CONT'D)

Procedure

Procedure for Loader With Attachments Control Harness (Cont’d)

Figure 10-60-8

Figure 10-60-7 1

3

2

P13842

1

The remote start tool (Item 1) [Figure 10-60-8] has three rocker switches.

P-28363

Connect the remote start tool (Item 1) [Figure 10-60-7] to the loader harness connector (Item 2) [Figure 10-606].

Figure 10-60-9

The connector (Item 3) [Figure 10-60-7] on the remote start harness is not used in the remote start procedure and should remain capped.

2 3

NOTE: The key switch on the right-hand side operator panel must be in the off position or the Remote Start Kit will not operate.

WARNING

1

N-19541

AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and the Remote Start Key Switch in the OFF position, the loader can still be started from the operator panel inside the cab. Placing the key switch of the remote start tool in the run position disconnects the operator panel key switch from the start circuit. If the service technician will be working in the engine area it is important to remove the operator panel keys.

W-2357-0899

The traction lock switch (Item 1) [Figure 10-60-9] is used to turn traction lock on or off. Push the switch to the override position. The switch will illuminate to indicate traction lock OVERRIDE, in this position the wheels are able to turn.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-9] is used to activate the auxiliary hydraulics.

Pressing the switch once will activate variable flow.

Pressing the switch again will activate maximum flow.

The switch will illuminate to indicate which flow rate is active. Pressing the switch a third time will turn the flow OFF. The switch is used when checking pressures and flow rate.

The auxiliary pressure release (Item 3) [Figure 10-60-9] is used to release hydraulic pressure to the front and/or rear auxiliary couplers. To release pressure; push and hold the switch for three seconds.

10-60-3

S220 Bobcat Loader Service Manual

REMOTE START (CONT'D) Procedure (Cont’d)

NOTE: With the engine running; pushing and holding the pressure release switch this will cause the engine to stop in three seconds. To relieve the pressure; continue to press the switch after the engine has stopped.

10-60-4

S220 Bobcat Loader Service Manual

SERVICE SCHEDULE Chart Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader.

WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0199

SERVICE SCHEDULE ITEM Engine Oil Engine Air Filter and Air System

SERVICE REQUIRED

HOURS 8-10

50

100

■

250

■

500

■

1000

Check the oil level and add as needed.

Check display panel. Service only when required. Check for leaks and damaged components.

Clean debris from oil cooler, radiator & grill.

Lubricate with multi-purpose lithium based grease.

Engine Cooling System Lift Arms, Cylinders, Bob-Tach Pivot Pins and Wedges Tires Check for damaged tires and correct air pressure.

Seat Bar, Control Interlocks, Seat Check the condition of seat belt. Clean or replace seat belt retractors as Belt, Seat Belt Retractors needed. Check the sear bar and control interlocks for correct operation. Clean dirt and debris from moving parts.

Bobcat Interlock Control Systems Check that four (4) BICS™ indicator lights and functions are activated. See (BICS™) details in this Manual.

Safety Signs and Safety Treads Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Operator Cab Check the fastening bolts, washers and nuts. Check the condition of the cab.

Indicators and Lights Check for correct operation of all indicators and lights.

Fuel Filter Remove the trapped water.

Heater and A/C Filters Clean or replace filters as needed during heating/cooling season.

Hydraulic Fluid, Hoses and Check fluid level and add as needed. Check for damage and leaks. Repair or Tubelines replace as needed.

Final Drive Trans. (Chaincase), Check oil level. Check for correct operation. Repair or adjust as needed.

Foot Pedals or Hand Controls, and Steering Levers Wheel Nuts ❏Check for loose wheel nuts and tighten to 105-115 ft.-lb. (142-156 N•m) torque Parking Brake Check operation.

Battery Check cables, connections and electrolyte level. Add distilled water as needed.

Engine/Hydro. Drive Belt Check for wear or damage. Check idler arm stop.

Alternator Belt Check tension and adjust as needed.

Air Condition Belt Check belt for wear. Adjust or replace as needed.

Bobcat Interlock Control System Check the function of the lift arm by-pass control.

(BICS™) Fuel Filter Replace filter element.

Steering Shaft Grease fittings.

Fan Drive Gearbox Check gear lube level.

Hydraulic Reservoir Breather Cap Replace the reservoir breather cap.

Hyd./Hydro. Filter ●Replace the filter element.

Engine Oil and Filter Replace oil and filter. Use CD or better grade oil and Bobcat filter.

Final Drive Trans. (Chaincase) Replace the fluid.

Hydraulic Reservoir Replace the fluid.

Case Drain Filters Replace the filters.

Engine Valves Adjust the engine valves.

*

^

❍

❏ Check wheel nut torque every 8 hours for the first 24 hours. * Inspect the new belt after first 50 hours. ● Also replace hydraulic/hydrostatic filter element at the first 50 hours and when the transmission warning light comes ON. ^ First oil and filter change must occur at 50 hours; 500 hours thereafter. ❍ When operating under severe conditions, change oil and filter every 250 hours.

■ Or every 12 months. ▼ Or every 5 years.

10-70-1

S220 Bobcat Loader Service Manual

Replacing Filter Element

If the filter element needs replacement, the CODE [0117] (Air Filter Plugged) will show in the HOURMETER / CODE DISPLAY (Item 2) [Figure 10-80-2].

Figure 10-80-1

Figure 10-80-3

AIR CLEANER SERVICE

B-16300

1

1

P-34864 B-15552 B-15553

OUTER FILTER

It is important to change the air filter element only when the Air Cleaner Icon in the right panel is ON (Item 1) [Figure 10-80-1] and you hear three beeps from the alarm.

Disengage the wing nut (Item 1) [Figure 10-80-3] and remove the dust cover.

Figure 10-80-4

Replace the inner filter every third time the outer filter is replaced or as indicated on (See Replacing Filter Element (Cont'd) on Page 10-80-2.)

Figure 10-80-2 1

2 P-34860

1

Remove the wing nut (Item 1) [Figure 10-80-4] and remove the outer filter element.

NOTE: Make sure all sealing surfaces are free of dirt and debris.

Install a new outer element, and install the wing nut.

B-15551

Install the dust cover and install the outer wing nut.

Press and hold the LIGHT Button (Item 1) [Figure 10-802] for two seconds.

Check the air intake hose and the air cleaner housing for damage. Make sure all connections are tight.

10-80-1

S220 Bobcat Loader Service Manual

Figure 10-80-6

AIR CLEANER SERVICE (CONT'D) Replacing Filter Element (Cont'd) Figure 10-80-5

1

1

P-34864

Install the new inner element.

P-34861

Install the dust cover and wing nut (Item 1) [Figure 1080-6].

INNER FILTER Only replace the inner filter element under the following conditions: •

Replace the inner filter element every third time the outer filter is replaced.

•

After the outer element has been replaced, start the engine and run at full RPM. If the HOURMETER / CODE DISPLAY shows [01-17] (Air Filter Plugged), replace the inner filter element.

Remove the inner filter element (Item 1) [Figure 10-805].

NOTE: Make sure all sealing surfaces are free of dirt and debris.

10-80-2

S220 Bobcat Loader Service Manual

ENGINE COOLING SYSTEM

Figure 10-90-2

Cleaning Cooling System Figure 10-90-1

1

2

P-43755

Lift the overflow tank (Item 1) [Figure 10-90-2] out of its mount bracket.

P-43754

Check the cooling system every day to prevent overheating, loss of performance or engine damage.

Remove the cotter pin (Item 2) [Figure 10-90-2] (both sides) from the oil cooler.

Figure 10-90-3

WARNING Wear safety glasses to prevent eye injury when any of the flollowing conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

W-2019-1285

Remove the rear grill. (See Removal And Installation on Page 50-60-1.)

Use air pressure or water pressure to clean the top of the oil cooler [Figure 10-90-1].

P-43756

Raise the oil cooler [Figure 10-90-3].

Use air pressure or water pressure to clean the top of the engine oil cooler.

10-90-1

S220 Bobcat Loader Service Manual

ENGINE COOLING SYSTEM (CONT’D) Cleaning Cooling System (Cont’d) Figure 10-90-4 Access Cover

P-43640

NOTE: The access cover (both sides) must be in place to ensure proper air flow through the oil cooler which will ensure correct cooling for the engine/hydraulic system [Figure 10-90-4].

10-90-2

S220 Bobcat Loader Service Manual

FUEL SYSTEM

Figure 10-100-2

WRONG

Fuel Specifications Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1.

The following is one suggested blending guideline which should prevent fuel gelling problems: Temp. F° (C°)

No. 2

No. 1

+15° (9°)

100%

0%

Down to -20° (-29°)

50%

50%

Below -20° (-29°)

0%

100% B-15602

We recommend an operator contact their fuel supplier for local recommendations.

Filling The Fuel Tank

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING! [Figure 10-100-2].

Install and tighten the fuel fill cap [Figure 10-100-1].

WARNING

Fuel Filter

Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire.

Figure 10-100-3

W-2063-0887

2

Figure 10-100-1

1

P-34865

1

P-43640

Remove the fuel fill cap (Item 1) [Figure 10-100-1].

See SERVICE SCHEDULE on Page 10-70-1 for the recommended service interval when to remove the water from the fuel filter.

Loosen the drain (Item 1) [Figure 10-100-3] at the bottom of the filter element to drain any water from the filter.

See SERVICE SCHEDULE on Page 10-70-1 for the recommended service interval when to replace the fuel filter.

To replace the fuel filter element, use a filter wrench to remove the filter element (Item 2) [Figure 10-100-3].

10-100-1

S220 Bobcat Loader Service Manual

FUEL SYSTEM (CONT'D) Fuel Filter (Cont’d) Clean the area around the filter housing. Put oil on the seal of the new filter element. Install the fuel filter, and hand tighten. Remove the air from the fuel system.

Removing Air From The Fuel System Figure 10-100-4

1

P-34865

After replacing the fuel filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system prior to starting the engine.

Loosen the air vent plug (Item 1) [Figure 10-100-4] at the top of the fuel filter.

Figure 10-100-5

1

P-34865

Operate the hand pump (priming bulb) (Item 1) [Figure 10-100-5] until the fuel flows from the air vent plug with out air bubbles.

Tighten the air vent plug.

10-100-2

S220 Bobcat Loader Service Manual

ENGINE LUBRICATION SYSTEM

Replacing Oil And Filter

Checking Engine Oil

Figure 10-110-2

Figure 10-110-1

1 1

P-34866 P-34866

See SERVICE SCHEDULE on Page 10-70-1 for the service interval for replacing the engine oil and filter.

Check the engine oil level every day.

Before starting the engine for the work shift, open the rear door. Remove the dipstick (Item 1) [Figure 10-1101].

Keep the oil level between the marks on the dipstick.

Run the engine until it is at operating temperature. Stop the engine.

Open the rear door. Remove the drain hose (Item 1) [Figure 10-110-2] from its storage position. Remove the cap and drain the oil into container.

Use a good quality motor oil that meets API Service Classification of CD, CE or better. (See Oil Chart below.)

Oil Chart RECOMMENDED SAE VISCOSITY NUMBER (LUBRICATION OILS FOR DIESEL ENGINE CRANKCASE)

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE (DIESEL ENGINES MUST USE API CLASSIFICATION CD, CF4,CG4) *Can be used ONLY when available with appropriate diesel rating.

10-110-1

S220 Bobcat Loader Service Manual

Figure 10-110-4

ENGINE LUBRICATION SYSTEM (CONT’D) Replacing Oil And Filter (Cont’d) Figure 10-110-3

2

1

P-34866

Remove the filler cap (Item 1) [Figure 10-110-4].

P-34866

Put 12 qts. (11 L) of oil in the engine.

Start the engine and let it run for several minutes. Stop the engine. Check for leaks and check the oil level. Add oil as needed if it is not at the top mark on the dipstick.

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil.

Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W-2103-1285

Remove the oil filter (Item 1) [Figure 10-110-3].

Clean the filter housing surface. Put clean oil on the new oil filter gasket. Install the filter and hand tighten only.

Install and tighten the drain cap on the drain hose.

10-110-2

S220 Bobcat Loader Service Manual

Figure 10-120-3

HYDRAULIC/HYDROSTATIC SYSTEM Checking And Adding Fluid Figure 10-120-1 Sight Gauge

1 P-4613

P-30011

NOTE: Before installing the fill cap, make sure the rubber gasket (Item 1) [Figure 10-120-3] is installed on the fill cap.

P-43757

Use only recommended fluid in the hydraulic system.

(See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1.)

Figure 10-120-4

To check the reservoir, use the following procedure: Put the Bobcat loader on a level surface. Lower the lift arms and tilt the Bob-Tach fully back. Stop the engine.

Check the fluid level at the sight gauge [Figure 10-1201]. The fluid level must show in the sight gauge.

1

Figure 10-120-2

P-34904

Hydraulic/Hydrostatic Filter Replacement See SERVICE SCHEDULE on Page 10-70-1 for the correct service interval.

1

Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.)

Use a filter wrench to remove the filter element (Item 1) [Figure 10-120-4].

P-43641

If fluid is needed, remove the fill cap (Item 1) [Figure 10120-2].

Clean the surface of the filter housing where the element seal contacts the housing. Put clean oil on the rubber seal of the filter elements.

Add the fluid as needed to bring the level to the center of the sight gauge.

Install and hand tighten the filter elements.

10-120-1

S220 Bobcat Loader Service Manual

Disconnect the hoses from the hydrostatic motor case drain filter (Item 1) [Figure 10-120-6].

HYDRAULIC/HYDROSTATIC SYSTEM (CONT'D) Replacing Hydraulic Fluid And Case Drain Filters

Remove the case drain filter and clean thoroughly with clean solvent.

Figure 10-120-5

Install the case drain filter and tighten the hoses.

Install the plug in the reservoir drain hose and tighten.

Install the motor cover.

Figure 10-120-7 1

P-31286

1

See SERVICE SCHEDULE on Page 10-70-1 for the service interval.

Replace the fluid if it becomes contaminated or after major repair.

Also clean the hydrostatic motor case drain filter thoroughly after a major repair.

Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.)

P-43785

Remove the left side access panel (Item 1) [Figure 10120-7].

Remove the left hydrostatic motor cover.

Pull the reservoir drain hose (Item 1) [Figure 10-120-5] out the motor cover hole. Remove the plug and drain the fluid into a container.

Figure 10-120-6

1 P-43786

10-120-2

S220 Bobcat Loader Service Manual

HYDRAULIC/HYDROSTATIC SYSTEM (CONT'D) Replacing Hydraulic Fluid And Case Drain Filters (Cont’d) Figure 10-120-8

1

P-37663

Remove the hoses from the attachments case drain filter (Item 1) [Figure 10-120-8]. Remove and discard the filter.

Install a new filter, tighten the hose fittings and install the cover.

Add the correct fluid to the reservoir until the fluid level is at the center of the sight gauge. (See Checking And Adding Fluid on Page 10-120-1.)

Lower the operator cab. Start the engine and operate the loader hydraulic controls. Stop the engine. Check for leaks. Check the fluid level in the reservoir and add as needed.

10-120-3

S220 Bobcat Loader Service Manual

FINAL DRIVE TRANSMISSION (CHAINCASE)

Replacing The Oil

Checking And Adding Oil

Figure 10-130-2

Figure 10-130-1

1 1

P-1616 P-31287

The chaincase contains the final drive sprockets and chains and uses the same type of oil as the hydraulic/ hydrostatic system.

(See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1.)

To drain the oil from the chaincase, remove the cover (Item 1) [Figure 10-130-2] which is installed over the drain plug at the rear of the chaincase.

Figure 10-130-3

To check the chaincase oil level, use the following procedure: Drive the loader on a level surface. Stop the engine.

Remove the plug (Item 1) [Figure 10-130-1] from the front of the chaincase housing.

1

If oil can be reached with the tip of the your finger through the hole the oil level is correct.

If the level is low, add oil through the check plug hole until the oil flows from the hole. Install and tighten the plug.

P-1619

Remove the drain plug (Item 1) [Figure 10-130-3] and drain the oil into a container.

Check the drain plug and replace if necessary.

10-130-1

S220 Bobcat Loader Service Manual

FAN GEARBOX Checking And Adding Oil Figure 10-140-1

Gear Lube Level

1

P7616

See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1 for the correct service interval.

Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.)

Remove the plug (Item 1) [Figure 10-140-1] to check the lubricant level.

When checking the gearbox lube level, make sure the level does not go above the center line of the shaft in the gearbox [Figure 10-140-1]. Use SAE 90W gear lube if the level is low.

10-140-1

S220 Bobcat Loader Service Manual

Figure 10-150-3

BOB-TACH Inspection And Maintenance

Bob-Tach Wedge

WARNING Bob-Tach wedges must extend through the holes in attachment. Levers must be fully down and locked.

Failure to secure wedges can allow attachment to come off and cause injury or death.

W-2102-0588

Wedge Must Contact Lower Edge Of Hole In the Attachment

Figure 10-150-1

B-15177

The spring loaded wedge (Item 1) [Figure 10-150-1] must contact the lower edge of the hole in the attachment (Item 1) [Figure 10-150-2] and [Figure 10-150-3].

If the wedge does not contact the lower edge of the hole [Figure 10-150-2] and [Figure 10-150-3], the attachment will be loose and can come off the Bob-Tach.

P-21234

1

Figure 10-150-4

P-31693

Move the Bob-Tach levers to engage the wedges [Figure 10-150-1]. The levers and wedges must move freely.

The wedges must extend through the holes in the attachment mounting frame (Inset) [Figure 10-150-1].

Figure 10-150-2 TS-1062

Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-150-4]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight.

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

1 P-31237

Lubricate the wedges (See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1.

See LUBRICATING THE LOADER on Page 10-160-1.)

10-150-1

S220 Bobcat Loader Service Manual

Figure 10-151-3

POWER BOB-TACH Inspection And Maintenance Figure 10-151-1

B-15177

1 Wedges Must Contact Lower Edge Of Hole In The Attachment P-31237

If the wedge does not contact the lower edge of the hole (Item 1) [Figure 10-151-3], the attachment will be loose and can come off the Bob-Tach.

B-15891A

Push and hold the BOB-TACH "WEDGES UP" switch [Figure 10-151-1] until wedges are fully raised. Push and hold the BOB-TACH "WEDGES DOWN" switch [Figure 10-151-1] until the wedges are fully down. The wedges must move freely.

Figure 10-151-4

Figure 10-151-2

TS-1062

1 P-31233

The wedges must extend through the holes in the attachment mounting frame (Item 1) [Figure 10-151-2] and must contact the lower edge of the hole in the attachment [Figure 10-151-2] and (Item 1) [Figure 10151-3].

Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-151-4]. Replace any parts including decals and lever that are damaged, bent, or missing.

Keep all fasteners tight. Inspect the hoses and fittings for leaks.

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

Lubricate the wedges. (See SERVICE SCHEDULE on Page 10-70-1. See LUBRICATING THE LOADER on Page 10-160-1.)

10-151-1

S220 Bobcat Loader Service Manual

Figure 10-160-3

LUBRICATING THE LOADER Procedure Figure 10-160-1

3

1 P-43784

3. Lift Arm Pivot Pin (Both Sides) [Figure 10-160-3].

P-43782

Figure 10-160-4

Lubricate the loader as specified in the SERVICE SCHEDULE for the best performance of the loader. (See SERVICE SCHEDULE on Page 10-70-1.)

Record the operating hours each time you lubricate the Bobcat loader.

4

Always use a good quality lithium based multi-purpose grease when you lubricate the loader. Apply the lubricant until extra grease shows.

Lubricate the following locations on the loader: 1. Rod End Lift Cylinder (Both Sides) [Figure 10-160-1].

P-31305

Figure 10-160-2 4. Base End Tilt Cylinder (Both Sides) [Figure 10-1604].

2

P-43783

2. Base End Lift Cylinder (Both Sides) [Figure 10-1602].

10-160-1

S220 Bobcat Loader Service Manual

Figure 10-160-7

LUBRICATION OF THE LOADER (CONT'D) Procedure (Cont'd) Figure 10-160-5

5 7

P-31308

7. Bob-Tach Wedge (Both Sides) [[Figure 10-160-7] P-31306

Figure 10-160-8

5. Rod End Tilt Cylinder (Both Sides) [Figure 10-160-5].

Figure 10-160-6

8

P10105

6

P-31307

8. 250 Hours: Steering Lever Shaft (three) [Figure 10160-8].

6. Bob-Tach Pivot Pin (Both Sides) [Figure 10-160-6].

10-160-2

S220 Bobcat Loader Service Manual

It is important to keep the same size tires on each side of the loader. If different sizes are used, each tire will be turning at a different rate and cause excessive wear. The tread bars of all the tires must face the same direction.

TIRE MAINTENANCE Wheel Nuts Figure 10-170-1

Recommended tire pressure must be maintained to avoid excessive tire wear and loss of stability and handling capability. Check for the correct pressure before operating the loader.

Tire Mounting Tires are to be repaired only by an authorized person using the proper procedures and safety equipment. Tires and rims must always be checked for correct size before mounting. Check rim and tire bead for damage.

P-31673

See SERVICE SCHEDULE on Page 10-70-1 for the service interval to check the wheel nuts [Figure 10-1701].

The rim flange must be cleaned and free of rust. The tire bead and rim flange must be lubricated with a rubber lubricant before mounting the tire, avoid excessive pressure which can rupture the tire and cause serious injury or death. During inflation of the tire, check the tire pressure frequently to avoid over inflation.

WARNING

When installing wheel nuts, tighten to 160 ft.-lb. (217 N•m) torque.

When checking wheel nuts, tighten to 140 ft.-lb. (190 N•m) torque .

Do not inflate tires above specified pressure. Failure to use correct tire mounting procedure can cause an explosion which can result in injury or death.

Tire Rotation

W-2078-1285

Figure 10-170-2

IMPORTANT Inflate tires to the MAXIMUM pressure shown on the sidewall of the tire. DO NOT mix brands of tires used on the same loader.

I-2057-0794

B-9976

Check the tires regularly for wear, damage and pressure.

(See Tires on Page SPEC-10-4.)

Rear tires usually wear faster than front tires. To keep tire wear even, move the front tires to the rear and rear tires to the front [Figure 10-170-2].

Revised May 04

10-170-1

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM BUCKET POSITION VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-90-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .20-90-2 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-90-2 Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . .20-90-1 Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-90-1 CYLINDER (LIFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-5 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-1 Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-4 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-3 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-20-1 CYLINDER (POWER BOB-TACH) . . . . . . . . . . . . . . . . . . . . . . .20-22-1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22-5 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22-1 Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22-4 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22-3 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22-2 CYLINDER (TILT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-6 Base Pin Removal And Installation . . . . . . . . . . . . . . . . . . . .20-21-3 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-1 Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-5 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-4 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21-1 FRONT AUXILIARY HYDRAULIC COUPLER BLOCK. . . . . . 20-120-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . 20-120-1 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20-120-1

HYDRAULIC SYSTEM

DRIVE SYSTEM

ELECTRICAL SYSTEM & ANALYSIS ENGINE SERVICE

SPECIFICATIONS

Continued On Next Page 20-01

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC CONTROL VALVE (ADVANCED CONTROL SYSTEM) (ACS) 2041-1 Actuator Removal And Installation (In Loader) . . . . . . . . . . . . . . . . . 20-41-1 Actuator Removal And Installation (Out Of Loader). . . . . . . . . . . . . . 20-41-4 Anti-Cavitation Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-21 Anti-Cavitation Valve/Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . 20-41-20 Auxiliary Electric Solenoid Disassembly . . . . . . . . . . . . . . . . . . . . . 20-41-26 Auxiliary Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . 20-41-25 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-5 BICS™ Valve, Removal And Installation . . . . . . . . . . . . . . . . . . . . . . 20-41-9 BICS™ Valve, Lift Arm By-Pass Orifice Disassembly And Assembly20-41-11 BICS™ Valve, Check Valve Disassembly And Assembly . . . . . . . . 20-41-12 BICS™ Valve, Lock Valve Disassembly And Assembly . . . . . . . . . 20-41-13 BICS™ Valve, Solenoid Disassembly And Assembly . . . . . . . . . . . 20-41-14 BICS™ Valve, Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-15 Cleaning And Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-27 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-16 Lift Base End Restrictor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-17 Lift Spool Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-22 Lift Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-23 Lift and Tilt Spool Disassembly And Assembly . . . . . . . . . . . . . . . . 20-41-24 Load Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-17 Main Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-18 Port-Auxiliary Section Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-27 Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-19

Continued On Next Page

20-02

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC CONTROL VALVE (FOOT CONTROL) . . . . . . . . . . . . . 20-40-1 Anti-Cavitation Valve, Lift Spool. . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-14 Anti-Cavitation Valve/Port Relief Valve, Tilt Spool. . . . . . . . . . . . . 20-40-13 Auxiliary Electric Solenoid Disassembly . . . . . . . . . . . . . . . . . . . . 20-40-29 Auxiliary Plug Removal And Installation . . . . . . . . . . . . . . . . . . . . 20-40-28 Auxiliary Spool Removal And Installation . . . . . . . . . . . . . . . . . . . 20-40-26 Backslide, Lock Valve Removal And Installation . . . . . . . . . . . . . . . 20-40-8 BICS™ Valve, Check Valve Removal And Installation . . . . . . . . . . 20-40-7 BICS™ Valve, Lift Arm By-Pass Orifice Removal And Installation . 20-40-6 BICS™ Valve, Removal And Installation . . . . . . . . . . . . . . . . . . . . . 20-40-5 BICS™ Valve, Solenoid Removal And Installation . . . . . . . . . . . . . 20-40-9 BICS™ Valve, Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-10 Cleaning And Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-30 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-10 Lift And Tilt Lock Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-15 Lift Spool And Detent Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-20 Lift Spool And Detent Disassembly . . . . . . . . . . . . . . . . . . . . . . . . 20-40-18 Lift Spool And Detent Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-24 Lift Spool And Detent Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-16 Load Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-11 Main Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-12 Port-Auxiliary Section Removal And Installation . . . . . . . . . . . . . . 20-40-30 Port Relief Valve, Lift Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-13 Port Relief Valve, Tilt Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-12 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 Rubber Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-14 Tilt Spool Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . 20-40-25 Tilt Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . 20-40-24

Continued On Next Page 20-03

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC CONTROL VALVE (SELECTABLE JOYSTICK CONTROL) (SJC) 20-42-1 Actuator Removal And Installation (In Loader) . . . . . . . . . . . . . . . . 20-42-1 Actuator Removal And Installation (Out Of Loader). . . . . . . . . . . . . 20-42-4 Anti-Cavitation Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-21 Anti-Cavitation Valve/Port Relief Valve . . . . . . . . . . . . . . . . . . . . . 20-42-20 Auxiliary Electric Solenoid Disassembly . . . . . . . . . . . . . . . . . . . . 20-42-26 Auxiliary Spool Removal And Installation . . . . . . . . . . . . . . . . . . . 20-42-25 BICS™ Valve, Removal And Installation . . . . . . . . . . . . . . . . . . . . . 20-42-9 BICS™ Valve, Lift Arm By-Pass Orifice Disassembly And Assembly 20-4211 BICS™ Valve, Check Valve Disassembly And Assembly . . . . . . . 20-42-12 BICS™ Valve, Lock Valve Disassembly And Assembly . . . . . . . . 20-42-13 BICS™ Valve, Solenoid Disassembly And Assembly . . . . . . . . . . 20-42-14 BICS™ Valve, Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-15 Cleaning And Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-27 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-16 Lift Base End Restrictor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-17 Lift Spool Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-22 Lift Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . 20-42-23 Lift and Tilt Spool Disassembly And Assembly . . . . . . . . . . . . . . . 20-42-24 Load Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-17 Main Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-18 Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-19 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-42-5 Port-Auxiliary Section Disassembly . . . . . . . . . . . . . . . . . . . . . . . . 20-42-27 HYDRAULIC FLUID RESERVOIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 Fluid Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 Hydraulic Fluid Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-4 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 HYDRAULIC PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-5 Check The Output Of The Hydraulic Pump . . . . . . . . . . . . . . . . . . . 20-60-1 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-4 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-60-2 HYDRAULIC PUMP (CHARGE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-1 Check The Output Of The Hydraulic Pump . . . . . . . . . . . . . . . . . . . 20-61-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-4 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-61-4

Continued On Next Page 20-04

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM (CONT’D) HYDRAULIC PUMP (HI FLOW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-62-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-62-13 High Flow Relief Adjustment Procedure . . . . . . . . . . . . . . . . . . . . 20-62-6 High Flow Relief Valve Removal and Installation . . . . . . . . . . . . . 20-62-8 Hydraulic Pump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-62-1 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-62-12 Inline Hydraulic Pump Test (High Flow). . . . . . . . . . . . . . . . . . . . .20-62-4 Inline Hydraulic Pump Test (Standard) . . . . . . . . . . . . . . . . . . . . .20-62-2 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-62-10 HYDRAULIC PUMP (HI-FLOW) (SELECTABLE JOYSTICK CONTROL) (SJC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-64-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-64-13 High Flow Relief Adjustment Procedure . . . . . . . . . . . . . . . . . . . . 20-64-6 High Flow Relief Valve Removal and Installation . . . . . . . . . . . . . 20-64-8 Hydraulic Pump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-64-1 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-64-12 Inline Hydraulic Pump Test (High Flow). . . . . . . . . . . . . . . . . . . . . 20-64-4 Inline Hydraulic Pump Test (Standard) . . . . . . . . . . . . . . . . . . . . . 20-64-2 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-64-10 HYDRAULIC PUMP (SELECTABLE JOYSTICK CONTROL) (SJC) . 20-63-1 Check The Output Of The Hydraulic Pump . . . . . . . . . . . . . . . . . . 20-63-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-63-5 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-63-4 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-63-2 HYDRAULIC SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 20-10-1 Tightening Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-5 HYDRAULIC/HYDROSTATIC FILTER . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Housing Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Mount Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-2 LIFT ARM BY-PASS CONTROL VALVE . . . . . . . . . . . . . . . . . . . . . . 20-50-1 Additional Inspection For Loaders W/Advanced Hand Controls . . 20-50-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-50-2 Inspecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-50-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-50-1 MAIN RELIEF VALVE (ACS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-31-1 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-31-3 Checking The Main Relief Valve At Front Aux. Hyd. . . . . . . . . . . . 20-31-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-31-2

Continued On Next Page 20-05

S220 Bobcat Loader Service Manual

HYDRAULIC SYSTEM (CONT’D) MAIN RELIEF VALVE (FOOT CONTROL) . . . . . . . . . . . . . . . . . . . . .20-30-1 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-30-2 Checking The Main Relief Valve At Front Aux. Hyd. . . . . . . . . . . .20-30-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-30-2 MAIN RELIEF VALVE (SELECTABLE JOYSTICK CONTROL) (SJC)20-32-1 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-32-3 Checking The Main Relief Valve At Front Auxiliary Hydraulics . . .20-32-1 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-32-2 POWER BOB-TACH BLOCK (EARLY MODELS). . . . . . . . . . . . . . .20-110-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-110-2 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-110-1 POWER BOB-TACH BLOCK (LATER MODELS). . . . . . . . . . . . . . . 20-111-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-111-2 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-111-1 REAR AUXILIARY DIVERTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-3 Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-8 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-100-1 Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-100-8

20-06

S220 Bobcat Loader Service Manual

Thank you very much for your reading.

Please Click Here Then Get More Information.