Bobcat 220 mini excavator service repair manual sn 508211999 & below

X 220 Excavator Service Manual (S/N 508211999 & Below)

6720230 (5–89)

Printed in U.S.A.

© Melroe Company 1989

CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii DELIVERY REPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii HYDRAULIC EXCAVATOR IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . iii PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1 DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1 UPPER WORKS & SWING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1 MAIN FRAME & TRACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1 ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1

PREVENTIVE MAINTENANCE

HYDRAULIC SYSTEM

DRIVE SYSTEM

UPPER WORKS & SWING SECTION

MAIN FRAME & TRACKS

ELECTRICAL SYSTEM

ENGINE SERVICE

TECHNICAL DATA

–3

220 (S/N 508211999 & Below) Excavator Service Manual

FOREWORD This manual is for the Bobcat hydraulic excavator mechanic. It provides necessary servicing and adjustment procedures for the hydraulic excavator and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, starting procedure, daily checks, etc.

A general inspection of the following items must be made after the hydraulic excavator has had service or repair: 1. Check that the operator canopy is in good condition and is not modified.

9. Safety treads must be in good condition.

2. Check that the operating canopy mounting hardware is tightened and is Melroe approved.

10. Check for the correct function of the the indicator lamps.

3.

The seat belt must be correctly installed, functional and in good condition.

11. Check hydraulic fluid level, engine oil and fuel supply.

4.

Inspect for loose or broken parts or connections.

12. Inspect for fuel, oil or hydraulic leaks..

5.

Machine signs must be legible and in the correct location.

13. Lubricate excavator.

6.

Steering levers, control levers and foot pedals must return to neutral. Control lock must lock controls securely.

14. Check the condition of the battery and cables.

7.

Inspect the air cleaner for damage or leaks. Check the condition of the element.

15. Check for any field modifications not completed.

Check the electrical charging system.

Recommend to the owner that all necessary corrections be made before the machine is returned to service.

8.

–1

the

hydraulic

FIELD MODIFICATION

220 (S/N 508211999 & Below) Excavator Service Manual

SAFETY INSTRUCTIONS

Instructions are necessary before operating or servicing machine. Read Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Failure to follow instructions can cause injury or death.

W–2003–0797

The following publications provide information on the safe use and maintenance of the excavator and attachments:

• The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

• The Operation & Maintenance Manual delivered with the excavator gives operating information as well as routine maintenance and service procedures. It is a part of the excavator and must stay with the machine when it is sold.

• The excavator has machine signs (decals) which instruct on the safe operation and care. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat Excavator dealer.

• The CIMA Safety Manual delivered with the excavator gives information for safe operating and standard signals.

• The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shop–type service and repair work.

Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death.

W–2044–1285

This notice identifies procedures which must be followed to avoid damage to the machine.

I–2019–0284

Safety Alert Symbol: This Safety Symbol is used for important safety messages. When you see this symbol follow the safety message to avoid personal injury or death.

• Wear tight fitting clothing and any other required safety apparel when operating or servicing the excavator.

• Wear safety glasses when maintaining or servicing the excavator.

• Exhaust gases can kill, vent engine exhaust outdoors.

• Know where fire extinguishers and first aid kits are located and how to use them.

• Do not run the excavator where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

• Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

• Do not use ether or starting fluids on an engine that has glow plugs. These starting aids can explode and injure you.

• Clean the excavator before doing any welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the excavator when welding.

• Have good ventilation when welding or grinding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced.

• Stop the engine and let it cool before adding fuel. No smoking!

• Use the procedure in this manual for installing, connecting and jump starting batteries. i

220 (S/N 508211999 & Below) Excavator Service Manual

SERIAL NUMBER LOCATIONS

A

Always use the serial number of the machine when requesting service information or when ordering parts.

Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

HYDRAULIC EXCAVATOR SERIAL NUMBER The excavator serial number plate is on the machine frame, at the left side near the front corner [A].

N–07348

ENGINE SERIAL NUMBER

B

The engine serial number is located on the engine block, near the fuel injection pump [B].

N–07349

DELIVERY REPORT

C

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the excavator is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [C].

ii

220 (S/N 508211999 & Below) Excavator Service Manual

HYDRAULIC EXCAVATOR IDENTIFICATION CONTROL LEVERS

OPERATOR CANOPY

ENGINE COVER BOOM

SWING LOCK UPPER WORKS

BLADE

TRACK

TRACK FRAME

GRAB HANDLES DIPPERSTICK CYLINDER

OPERATOR SEAT

BUCKET CYLINDER

BUCKET LINK

BOOM CYLINDER CONTROL LOCK BLADE CYLINDER DIPPERSTICK

BUCKET

B–14810 B–14811

iii

220 (S/N 508211999 & Below) Excavator Service Manual

PREVENTIVE MAINTENANCE Page Number

PREVENTIVE MAINTENANCE

AIR CLEANER SERVICE Replacing the Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 COOLING SYSTEM Coolant Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Coolant Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6 ENGINE COVER Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3 ENGINE LUBRICATION SYSTEM Checking the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 Engine Oil and Filter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 FINAL DRIVE CASE Checking Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–12 Draining Final Drive Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–12 FUEL SYSTEM Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3 Fuel System Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3 HYDRAULIC SYSTEM Checking and Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7 Replacement of the Hydraulic Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8 Hydraulic Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8 LUBRICATION OF THE EXCAVATOR Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10 SERVICE SCHEDULE Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 USING A BOOSTER BATTERY (JUMP STARTING) Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–9

–1––1–

220 (S/N 508211999 & Below) Excavator Service Manual

SERVICE SCHEDULE Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Hydraulic Excavator.

Instructions are necessary before operating or servicing machine.

Read Operation & Maintenance Manuals, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Failure to follow instructions can cause injury or death.

W–2003–1289

ITEM

SERVICE REQUIRED

Engine Air Cleaner Engine Oil Engine Coolant System Indicator Lights Operator Canopy Seat Belt & Control Lock Safety Signs (Decals) & Safety Treads

Check & empty dust cup as required.

Check the oil level & add oil as needed.

Check radiator coolant level.

Check for correct operation.

Check the fastening bolts, nuts, & condition of canopy.

Check the condition, operation & that fasteners are tight.

Check for damaged signs (decals) and safety treads.

Replace any safety signs and safety treads that are damaged or worn.

Check & adjust tension.

Check fluid level.

Drain water and sediment from fuel tank.

Lubricate two grease fittings.

Lubricate one grease fitting.

Replace oil & filter element.

Tracks Hydraulic Reservoir Fuel Tank Swing Circle Swing Pinion Engine Oil & Filter All Machinery Pivot Points Alternator Belt Final Drive Case Hydraulic Filter Fuel Filter Battery Air Cleaner Cooling System Alternator & Starter Engine Valve Clearance Cooling System Hydraulic Tank Final Drive Case

8–10

50

100

250

500 1000

Lubricate 20 grease fittings.

Check & adjust tension.

Check fluid level & add oil as needed.

Replace filter element.

Replace filter element.

Check & clean cable ends & check electrolyte level.

Replace the filter element.

Clean the radiator fins.

Check the condition.

Check & adjust valve clearance.

Drain, flush & add new coolant to the cooling system.

Change the fluid, clean fill neck strainer & suction strainer.

Change the fluid.

After the first 250 hours of machine operation do the following procedures: • Change oil in final drive case.

• Check and adjust engine valve clearance.

–1–1–

220 (S/N 508211999 & Below) Excavator Service Manual

ENGINE COVER

A

Procedure

AVOID INJURY Never service or adjust the machine when the engine is running unless instructed to do so in the manual.

W–2012–0290 N–07367

Keep the engine cover closed when operating the machine.

W–2141–0189

B

Open the engine cover to service the engine. Pull on the latches and lift the engine cover until it is fully raised [A].

1 AIR CLEANER SERVICE Replacing the Filter Element See the Service Schedule Page 1–1 for the correct service interval.

Service the air cleaner as follows: 1. Remove the dust cup (Item 1) [B].

N–07368

C

2. Remove the wing nut (Item 1) [C].

1

N–07369

D

3. Remove the filter element [D].

4. Check the air cleaner housing for damage.

5. Install a new air filter element. Install and tighten the wing nut.

6. Install the dust cap so the arrow points up.

7. Check that the air cleaner hose clamps are tight.

N–07370

–1–2–

220 (S/N 508211999 & Below) Excavator Service Manual

FUEL SYSTEM

A

Fuel Specifications Use Number 2 diesel fuel in the engine. During very cold temperatures, Number 1 fuel can be used.

Fuel System Service

1

The fuel level in the tank is indicated by the plastic tube (Item 1) [A] on the side of the tank.

N–07371

Stop and cool the engine before adding fuel.

NO SMOKING! Failure to obey warnings can cause an explosion or fire.

B

W–2063–0887

Use the key to unlock the fuel fill cap [B].

N–07372

Turn the fill cap to remove it from the fuel tank [C].

C

NOTE: The fuel fill strainer can be removed for cleaning. Make sure it is installed before adding fuel to the tank.

Use a clean, approved safety container to add fuel to the tank.

Add fuel only in an area that has a free movement of air and no open flames or sparks. NO SMOKING! After the tank is full, install and tighten the fuel fill cap.

N–07373

–1–3–

220 (S/N 508211999 & Below) Excavator Service Manual

FUEL SYSTEM (Cont’d)

A

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W–2103–1285 N–07375

To remove the water and sediment from the fuel tank, open the drain in the bottom of the tank [A].

–1–4–

220 (S/N 508211999 & Below) Excavator Service Manual

ENGINE LUBRICATION SYSTEM

A

Checking the Engine Oil Check the engine oil every day.

Stop the engine. Open the engine cover.

Remove the dipstick [A].

Keep the oil level between the marks on the dipstick.

Use a good quality motor oil that meets API Service Classification of CC or CD. (See Fuel, Coolant and Lubricants Chart Page 8–9.)

N–07378

Engine Oil and Filter Replacement

B

See the SERVICE SCHEDULE Page 1–1 for the correct service interval.

Use the following procedure to change the oil and filter: Run the engine until it is at operating temperature.

Turn the upper works so there is clearance for the engine oil drain plug. Stop the engine.

1

Remove the drain plug (Item 1) [B]. Drain the oil into a container.

N–07379

C

Remove the oil filter (Item 1) [C], using a filter wrench.

Clean the filter housing surface. Put clean oil on the filter gasket. Install the new filter and hand tighten only.

1

N–07380

Remove the oil fill cap [D]. Put 3.5 quarts (3,4 L) of oil into the engine. (See Fuel, Coolant and Lubricants Chart Page 8–9.)

D

Start the engine and let it run for several minutes. Stop the engine. Check the oil filter for leaks.

Check the oil level and add oil as needed to bring it to the top mark on the dipstick.

N–07381

–1–5–

220 (S/N 508211999 & Below) Excavator Service Manual

COOLING SYSTEM

A

Coolant Level When the engine is cool, remove the radiator cap [A].

The coolant level must be 3/4”–1” (19–25 mm) below the radiator filler neck.

If the coolant level is low, add premixed coolant (50% ethylene glycol and 50% water) to the radiator.

Coolant Replacement

N–07382

B Do not remove radiator cap when the engine is hot. You can be seriously burned.

W–2070–1285

Turn the upper works so there is access to the engine and radiator underneath. Stop the engine.

1

Loosen and remove the radiator cap [A].

Open the radiator drain valve (Item 1) [B].

Drain all the coolant from the system.

N–07383

When all the coolant is removed, close the drain valve.

Premix 50% water and 50% ethylene glycol in a separate container. Fill the radiator with premixed coolant until it is full.

Run the engine at idle speed for about 5–10 minutes to remove the air from the cooling system (leave the radiator cap off during this operation).

Stop the engine. Check the coolant level and add as needed, bringing it 3/4”–1” (19–25 mm) below the filler neck. Install the radiator cap and tighten.

Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure.

• Flying debris or loose material is present.

• Engine is running.

• Tools are being used.

W–2019–1285

–1–6–

220 (S/N 508211999 & Below) Excavator Service Manual

HYDRAULIC SYSTEM

A

Checking and Adding Fluid To check and add hydraulic fluid to the reservoir, use the following procedure: Put the machine on a flat surface.

Retract the dipperstick and bucket cylinders, put the bucket on the ground, and raise the blade. Stop the engine.

1

Check the hydraulic fluid level, it must be visible and between the marks in the sight gauge (Item 1) [A].

N–09091

B

If the fluid level is low, remove the four bolts from the reservoir cover [B].

N–09161

C

Remove the reservoir fill cover [C].

Add the correct fluid to the reservoir until it is at the top mark in the sight gauge [A]. (See Fuel, Coolant and Lubricants Chart Page 8–9.)

Install the reservoir cover, make sure the O–ring is in the correct position.

Install and tighten the bolts.

N–09162

–1–7–

220 (S/N 508211999 & Below) Excavator Service Manual

HYDRAULIC SYSTEM (Cont’d)

A

Replacement of the Hydraulic Filter See the Service Schedule Page 1–1 for the correct service interval.

1

Open the engine cover. Use a filter wrench and remove the filter element (Item 1) [A].

Clean the housing where the filter gasket makes contact.

Put clean fluid on the gasket. Install the new filter element and hand tighten only.

Start the engine. Run the machine through the hydraulic functions. Stop the engine. Check the fluid level at the reservoir and add as needed. Check the filter area for leaks.

N–09163

B

Hydraulic Reservoir

2

See the Service Schedule Page 1–1 for the correct service interval.

Move the upper works so there is a clearance for the reservoir between the track frame.

Retract the dipperstick and bucket cylinder, lower the bucket to the ground. Stop the engine.

3

1

Remove the hydraulic filter. Remove the drain plug (Item 1) [B] from the bottom of the reservoir.

Remove the hose clamps (Item 2) [B] and disconnect the hoses. Remove the bolts (Item 3) [B] from the flange.

Turn the bolts into the threaded holes in the flange to push the mesh screen out of the reservoir.

N–09090

Clean all the parts with clean solvent and air dry them.

Replace the parts and tighten the bolts, hose clamps and drain plug.

Add approximately 7.0 gals. (26,5 L) of fluid to the reservoir. (See Fuel, Coolant and Lubricants Chart Page 8–9.)

Run the machine through the hydraulic functions. Stop the engine. Check the fluid level and add as needed.

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

W–2103–1285

–1–8–

220 (S/N 508211999 & Below) Excavator Service Manual

USING A BOOSTER BATTERY (JUMP STARTING)

A

Procedure

1

If it becomes necessary to use an extra battery to start the engine, BE CAREFUL! Make sure the swing lock pin is in the engaged position.

The key switch must be in the OFF position.

2

The booster battery must be 12 volt.

Open the engine cover.

Connect the end of the first cable to the positive (+) terminal of the booster battery. Connect the other end of the same cable to the starter terminal (Item 1) [A].

N–07387

Connect the end of the second cable to the negative (–) terminal of the booster battery. Connect the other end of the same cable to the machine frame (Item 2) [A].

NOTE: Also see Cold Starting Procedure in the Operation & Maintenance Manual.

Start the engine. After the engine is running, remove the cable (Item 2) [A] connected to the frame first.

Disconnect cable from the starter terminal (Item 1) [A].

Keep arcs, sparks, flames and lighted tobacco away from batteries. When jumping from booster battery make final connection (negative) at engine frame.

Do not jump start or charge a frozen battery.

Warm battery to 60°F. (16°C.) before connecting to a charger. Unplug charger before connecting or disconnecting cables to battery.

Battery gas can explode and cause serious injury.

Damage to the alternator can occur if:

• Engine is operated with battery cables • •

W–2066–0490

disconnected.

Battery cables are connected when using a fast charger or when welding on the loader (Remove both cables from the battery).

Extra battery cables (booster cables) are connected wrong.

I–2023–1285

–1–9–

220 (S/N 508211999 & Below) Excavator Service Manual

LUBRICATION OF THE EXCAVATOR

A

Procedure Lubricate the Hydraulic Excavator as specified in the Service Schedule Page 1–1 for the best performance of the machine.

1 2

2

Always use a good quality lithium based multi–purpose grease when lubricating the machine. Apply the lubricant until extra grease shows.

3 Ref. Description (# of Fittings) 1. Blade Cylinder Rod End (1) [A].

2. Blade Pivots (2) [A].

3. Blade Cylinder Base End (1) [A].

N–07397

B

4. Boom Cylinder Rod End (1) [B].

4

N–07398

C

5. Boom Pivot Pin (1) [C].

6. Boom Swing Bracket Pivot (2) [C].

7. Boom Cylinder Base End (1) [C].

5

6

6

7

N–07399

8. Boom Cylinder Rod End (1) [D].

9. Dipperstick Cylinder Base End (1) [D].

D

9

8 N–07400

–1–10–

220 (S/N 508211999 & Below) Excavator Service Manual

LUBRICATION OF THE HYDRAULIC EXCAVATOR (Cont’d)

A 10

Procedure (Cont’d) Ref. Description (# of Fittings)

11

10. Dipperstick Cylinder Rod End (1) [A].

11. Dipperstick Pivot Pin (1) [A].

12. Bucket Cylinder Base End (1) [A].

12

N–07401

B

13. Bucket Cylinder Rod End (1) [B].

14. Bucket Link Pivots (2) [B].

15. Bucket Pivots (4) [B].

14 15 13 15 14 15 N–07402

16. Boom Cylinder Base End (1) [C].

C

17. Swing Circle Pinion (1) [C].

16

17

N–07403

18. Swing Circle (2) [D].

D

18

N–07404

–1–11–

220 (S/N 508211999 & Below) Excavator Service Manual

FINAL DRIVE CASE

A

220ExcavatorServiceManual(S/N508211999&Below)#6720230–PreventiveMaintenanceSection

Checking Oil Level Put the machine on a flat level surface.

1

Position the plug (Item 1) [A] parallel to the ground.

Remove one of the plugs (Item 1) [A].

Add oil through the hole if the oil level is below the hole.

(See Fuel, Coolant and Lubricant Chart Page 8–9.)

Install and tighten the plug.

Repeat the procedure for the other side.

P–05906

Draining Final Drive Case

B

See the Service Schedule Page 1–1 for the correct service interval.

Put the machine on a flat level surface with the plugs positioned as shown in figure [A].

Remove the bottom plug (Item 1) [B] and the top plug (Item 2) [B].

2

After the oil is removed, install and tighten the bottom plug.

1

Add .33 quarts (0,3 L) of oil to the top plug hole. Install the plug.

Use the same procedure for Checking Oil Level. Add oil as needed.

P–05907

Repeat the procedure for the other side.

–1–12–

220 (S/N 508211999 & Below) Excavator Service Manual

Thank you very much for your reading.

Please Click Here Then Get More Information.