SER VICE MANUAL
T5.105
T5.1
T5.95
ElectroCommand
ElectroCommand
ElectroCommand
T5.105
T5.105
T5.105
T5.1
T5.1
T5.1
T5.95
T5.95
T5.95
Link Product / Engine
ElectroCommand International Region
ElectroCommand Europe
ElectroCommand North America
ElectroCommand Europe
ElectroCommand International Region
ElectroCommand North America
ElectroCommand International Region
ElectroCommand North America
ElectroCommand Europe
F5DFL413B*A006
F5DFL413B*A006
F5DFL413B*A006
F5DFL413A*A002
F5DFL413A*A002
F5DFL413A*A002
F5DFL413C*A003
F5DFL413C*A003
F5DFL413C*A003
INTRODUCTION
Engine and crankcase
[10.216] Fuel tanks
[10.414] Fan and
[21.1 1 Semi-Powershift transmission
transmission external controls transmission internal components
[21.1 18] T ransmission/Rear drive .
Four-Wheel Drive (4WD) system
[23.202] Electro-hydraulic control
Drive shaft
Front axle system
Powered front axle
Front bevel gear set and dif ferential
[25.108] Final drive hub, steering knuckles, and shafts
Rear axle system
[27.100] Powered rear axle
Rear bevel gear set and dif ferential
Planetary and final drives
Spur gear and final drives
[31.104] Rear control
[31.1 14] T wo-speed rear Power T ake-Of f (PT
16] rear Power T f (PT
Brakes and controls .
Hydraulic service brakes
10] Parking brake parking lock
[33.220] T railer brake hydraulic control
Hydraulic systems
[35.000] Hydraulic systems
Fixed displacement pump
Regulated/Low pressure system
[35.204] Remote control valves
14] hitch control valve
Hitches, drawbars, and implement couplings
10] Rear hitch
Steering
[41.101] Steering control
[41.106] T rods
Hydraulic control components
Cylinders
Electrical systems
[55.000] Electrical system
[55.100] Harnesses and connectors
Engine starting system
[55.301] Alternator
[55.408] W arning indicators, alarms, and instruments
[55.DTC] F AUL T CODES
[90.100] Engine hood and panels
Capacities
Capacities
Fluid capacities and lubricant specifications
SER VICE MANUAL
T5.105
T5.1
T5.95
ElectroCommand
ElectroCommand
ElectroCommand
[10.001] Engine and crankcase . . .
ElectroCommand , ElectroCommand , ElectroCommand
[10.216] Fuel tanks . .
ElectroCommand , ElectroCommand , ElectroCommand
Exhaust Gas Recirculation (EGR) - Diesel Particulate Filter (DPF) exhaust treatment
ElectroCommand , ElectroCommand , ElectroCommand
Fan and drive
ElectroCommand , ElectroCommand , ElectroCommand
EngineEngine and crankcase - 001
T5.105
T5.1
T5.95
ElectroCommand
ElectroCommand
ElectroCommand
Engine - General specification
T5.95
T5.95 T5.105
Coolant pump
Coolant thermometer
T iming
Intake:
GENERAL SPECIFICA TIONS
start: before P .M.S.
end: after P
Exhaust:
start: before P
end: after P .M.S.
4 Cylinders
overhead valves operated tappets, rods and rocker arms via the camshaft located the engine block; the camshaft driven the crankshaft using straight - tooth gears
Clearance between valves and rocker arms with engine The valve clearance hydraulically manual adjustment not necessary
T urbocharging T urbocharged with intercooler
Air cleaning dual cartridge dry air cleaner , with clogged filter indicator with centrifugal pre - filter and automatic dust ejector
Fuel filtration mesh prefilter the supply suction line filter with water - fuel separator , low pressure filter and sensor
Priming pump
Injection pump
T ype
Nozzles type
Injection pressure
Filling: Engine sump
Fuel tank
Anti - pollution system
T ype:
Manual mounted the suction line filter BOSCH
High pressure Common Rail control unit HPCRElectro - injectors
Exhaust gas recycling system EGR
Particulate filter DPF*
Recommended frequency for renewing filter every 3000 hours
NOTE: * - For filter maintenance please refer to: ( Diesel Particulate Filters (DPF) - Dynamic description manual regeneration the diesel particulate filter (DPF) )
Engine - Install
- Refit the flexible belt the alternator and take the slack according the procedure AlternatorT ension adjust belt
- Reposition the compressor and the relevant belt following this procedure:
- Reposition the compressor the support and with the relevant pipe support secure with the screws - T o fit the belt polyv use the tool 38020001 1 . (1) Compressor clutch actuator drive (2) polyv belt pulley outer (3) T ool used drive the tool; this recess houses the bracket (1) (4) . T ail. Used drive the polyv belt the pulley (5) Thanks this where the outer edge (2) the tool remains hitched the compressor
- T ake out the bolts (1) and the related compressor clutch dust cover
Make sure that the polyv (2) belt perfectly housed the fan pulley
- Move the belt (2) near the compressor pulley keeping the tool 38020001 1 under the hook onto the clutch the compressor the innermost part slightly force the WLAPL4S10C143A
- With your left hand the fan and right hand the move both clockwise take the belt onto the belt the compressor
- Put the dust cup back onto the compressor clutch and tighten the three screws taking care spread a film thread lock the ends they not come
- Where reposition the viscous joint and the cooling
- Apply the required torque settings ( see engine tion)
- Insert the three hooks the chain the eyelets the engine using the lift the assembly f the platform support.
10. - Position the engine the front axle, trying avoid incorrect operations with the hoist not let the engine fan damage the fins the radiator , then join the two assemblies together with the four ing bolts and the necessary adjuster spacers for the monobloc / sump support.
1 - Reposition the movable tool for dismantling tractors 380000569 under the engine and place a wooden block between the point contact between the tool and
WLAPL4S10C142A
NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please