MODEL: ABR800 AV CABINET ASSEMBLY INSTRUCTIONS
IMPORTANT INFORMATION! 1) Before starting assembly please take time to familiarise yourself with the instructions and the components listed on the back page, as this product could be unstable if incorrectly installed. 2) Do not place hot or cold items against or in close proximity to any glass surface unless an adequately thick insulating material is used to prevent such items coming into contact with the glass. 3) Do not strike the glass with hard or pointed items. 4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary; do not use washing powders or other substances containing abrasives as these may scratch the glass. 5) Do not sit or stand upon horizontal glass surfaces. 6) In order to maintain a high quality finish, when cleaning wooden panels please use a soft cloth with a suitable furniture polish if required. 7) Alphason Designs uses real wood veneers, consequently slight colour and pattern variation may occur and does not indicate a product defect. With natural wood, exposure to direct sunlight can produce colour change and should be avoided. Any slight change in colour over time does not indicate a product defect.
PLEASE NOTE OTHER TOOLS REQUIRED: A HAMMER CROSS-HEAD SCREWDRIVER
Please Note: Maximum load for this support is 80Kg. This support must be assembled in accordance with these assembly instructions. Maximum load for each glass shelf is 60kg. Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.
Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955 info@alphasondesigns.com
www.alphasondesigns.com
issue AI-04 08/07 181751
STAGE 1
1.
• Screw dowels
s
x4 into side panels
C
and
D
.
D s C
x4
s
STAGE 2 • Place base panel A on its back edge, on a clean flat surface to avoid scratching. Using screws u attach panels F to panel A . • Insert 4x cams t into large holes in panel A . Ensure arrows are pointing to the outside edge of the panel. • Assemble side panels C and D onto panel Tighten cams in base panel A .
A
2.
t
u
x4
t x6
D
A
C F
t
t
.
u
3.
STAGE 3
E
• Position all remaining cams t in panels C and D . Once again ensure the arrows are pointing to the outside edge.
E into grooves in sides of panels C and D A. • Ensure back panel E is correctly located before proceeding to • Slot back panel and base panel
C t
,
next stage.
t A
x4
D
4.
STAGE 4 • Screw all remaining dowels not to over tighten.
s
into top panel
B
s
x4
s
. Take care
B
5.
B STAGE 5
C
• Assemble top panel B as shown in fig 5. Ensure dowel fixings align with corresponding holes in panels C and
D
• Tighten all cams
t
D
.
from stage 3.
issue AI-04 08/07 181751
STAGE 6 • Position location tape pieces r around the rebate in cabinet door ensure these are equally spaced around the rebate. • Place glass panel H into the rebated area. Ensure this is firmly stuck in place. • Fit all pine tree clips v into correct holes in the cabinet door . You may need a light hammer to get these in to place. ! Take extra care when carrying out this step..
6.
G
6a.
7.
r
•
G
p
k
n
j
iii Connecting screw
ii Use in stage 8
STAGE 7 Using screws k
, screw part i from flap hinge corresponding rebates in the cabinet door G .
• Using screws p attach both door plates side of the door G .
n
8.
•
j
into the 3
at either
p n
k
x10
G
• Remove connecting screw from flap hinges j . This will form 2 halves for the following assembly steps. i Use in stage 7
j
r
x6
H
G
STAGE 6a
v
v
k
n
x2
STAGE 8 Using screws k
j
attach part ii from flap hinge half rebates in the cabinet base panel A .
j
to the
k j
A
j
STAGE 9
9.
p
p
l
m
• Attach left and right hand flap stays l and m using screws p . The braking force of the flap stays may require adjustment. This can be achieved by turning the screw arrowed clockwise to tighten the movement or anticlockwise to loosen the movement. issue AI-04 08/07 181751
STAGE 10 • Carefully assemble the door onto the base panel. • Re-Connect hinges j by using connecting screw from stage 6a.
10.
j
j
11.
STAGE11 • Using connecting screw stays to the door plates
o n
o
, attach both left and right hand flap .
x2
n o
12.
STAGE 12 • Attach L-Shaped brackets y with screws z , into all four corners of the back panel in positions shown.
y
y
z
y
z
z
x4
x12
13.
STAGE 13 • Carefully lay the cabinet on its back. Push roller glides roller glide panels F . • Turn cabinet around to sit on roller glides q .
q
into
F q w
14.
x4
x
x2
q
q STAGE 14 • Finally insert shelf pegs in the side panels.
x w l
x4
• Place glass shelf
l
w
into desired positions
into cabinet.
• Attach 1 door buffer x to the top end of each side panel C and D . issue AI-04 08/07 181751
MODEL: ABR800 CERTIFICATE OF CONFORMITY C O M P O N ENT
DESCRIPTION
QTY
A
BASE PANEL
1
B
TOP PANEL
1
C LEFT END PANEL D RIGHT END PANEL
2
E
1
BACK PANEL
F
ROLLER GLIDE PANEL
2
G
CABINET DOOR
1
H
GLASS PANEL FOR DOOR
1
I
GLASS SHELF
1
PACKED BY
issue AI-04 08/07 181751
C O M P O NENT
DESCRIPTION
QTY
FLAP HINGE (During assembly this hinge splits into 2 parts)
3
j
310007
k
3 x 12 SCREW
18
l
LEFT HAND FLAP STAY
1
m
RIGHT HAND FLAP STAY
1
n
DOOR PLATE
310008
2
o
CONNECTING SCREW
2
p
4 x 15 SCREW
12
q
ROLLER GLIDE
4
r
LOCATION TAPE
10
s
35mm DOWEL
8
t
CAM
8
u
4 x 25 SCREW
6
v
PINE TREE CLIP
6
w
SHELF PEG
4
x
DOOR BUFFERS
2
x1
ALLEN KEY (suitable for tightening cams)
1
y
L-SHAPED BRACKET
4
3 x 12 SCREW
12
z
KIT NUMBER
This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your issue correspondence to the address given at the bottom of the front page.
310009
310011
310012
AI-04 08/07 181751