HI-FI SEPARATES SUPPORT MODELS: AD5/47-s AD5/47-CPB
ASSEMBLY INSTRUCTIONS
�
BEFORE STARTING THIS ASSEMBLY PLEASE TAKE TIME TO FAMILIARISE YOURSELF WITH THE COMPONENTS LISTED ON THE BACK PAGE
Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955
www.alphasondesigns.com
issue 06 02/07 181659
IMPORTANT
d
BEFORE STARTING THIS ASSEMBLY, PLEASE TAKE TIME TO FAMILIARISE YOURSELF WITH THE COMPONENTS AS LISTED ON THE BACK PAGE.
d
STAGE 1 Place glass shelf A on clean flat surface to prevent scratching. (Please note the AD5/47-CPB should be assembled with the glossy side down). Remove spigot nut f from the long rod d (to be used later in stage 5). Place the top caps j through the holes from the underside. Place top tube end plugs k over the three small holes with the flat surface facing down. Insert long rods d through tube end plugs k and small holes in glass top shelf A then into top caps and tighten by hand.
k
d
k
j A k j j
o
STAGE 2
m
Fit the tubes B over rods and locate on tube end plugs. Ensure the tube matches up with the top caps. Place tube end plugs m over rods and into tubes B . Insert plastic spacers o over rods. Locate and position second glass shelf A onto the three rod assemblies. Ensure that the large cable tidy holes align with that of the other shelves. Place tube end plugs m over rods. Fit the tubes B over rods and locate on tube end plugs m . Place tube end plugs m over rods and into tubes. Place third glass shelf over rods.
o o m
k
h
B k
B k
g
g
m
B
STAGE 3 Ensure that the cable tidy holes align with that of the other shelves.
A
g
m
o
Place tube end plugs m over rods. (as shown) Locate and the screw extension nut h at the end of rod Insert second rods g into the extension nut h and tighten by hand. Repeat stage 2 for the fourth shelf.
d.
m d
h
h m
m d
d
issue 06 02/07 181659
o
STAGE 4 o
o
Repeat stage 2 for the last shelf using the longer tubes
C
A C C
l
C m
f m
e p
m
l
STAGE 5 l
Once the last shelf is in place, locate and screw both washers p & e , then the spigot nut f onto the rods. Use spanner
f e p
t to tighten the spigot nuts f .
IT IS IMPORTANT THAT THE SPIGOT NUT IS SECURELY TIGHTENED AT THIS POINT AS THIS WILL INCREASE THE UNIT'S STRUCTURAL STABILITY. Locate and position cover cap l over assemblies. (ensure cover cap locates securely on spigot nut).
s
Assemble spikes s Adjust spikes & lock by tightening the nut. Or Insert plastic foot r
u
r Or l
v
f e p
l
STAGE 6 With the product now turned the right way up, insert the cable mouldings v in the top glass shelf and u in the other shelves.
STAGE 7 Place cable covers x & around cable tidy mouldings v & u
w
w
x
issue 06 02/07 181659
COMPONENT
CERTIFICATE OF CONFORMITY MODELS: AD5/47-s & AD5/47-CPB DESCRIPTION
A
QTY
PACKED BY
5
GLASS SHELF AD5/47-CPB - 141105 AD5/47-S - 141104
B
SHORT TUBE
AD5/47-CPB - 108144 AD5/47-S - 438144
C
LONG TUBE
AD5/47-CPB - 108230 AD5/47-S - 438230
d
LONG ROD
e
WASHER
g
SHORT ROD
h
EXTENSION NUT
j
TOP CAPS
3
k
TOP TUBE END PLUGS (with large hole)
3
l
COVER CAPS
3
m
TUBE END PLUGS
m
TUBE END PLUGS
f
9 3
SPIGOT NUT 111398
3
111337
3
202113
202139
5
16 200002 x 2
o
PLASTIC SPACER
p
NYLON WASHER
3
r
FOOT
3
s
SPIKE AND NUT
3
t
M6 / M8 SPANNER
u
LONG CABLE TIDY MOULDING
v
SHORT CABLE TIDY MOULDING
w
LONG CABLE COVER
x
SHORT CABLE COVER
202210
202213
12
1 4 1
202211 AD5/47-CPB - 180335 AD5/47-S - 180333
AD5/47-CPB - 180334 AD5/47-S - 180332
1 3
This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your correspondence to: Alphason House, Bolton Road, Atherton, Greater Manchester. M46 9AW. UK. issue 06 02/07 181659 Tel. +44 (0) 1942 885600 Fax. +44 (0) 1942 876955.