http://www.alphasondesigns.com/products/asp900w/instructions_ASP900_B,LO_&_W_01_en

Page 1

AV STAND

MODEL: ASP900-W, LO & B

ASSEMBLY INSTRUCTIONS

IMPORTANT INFORMATION! 1) Before starting assembly please take time to familiarise yourself with the instructions and the components listed on the back page, as this product could be unstable if incorrectly installed. 2) Do not place hot or cold items against or in close proximity to any glass surface unless an adequately thick insulating material is used to prevent such items coming into contact with the glass. 3) Do not strike the glass with hard or pointed items. 4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary; do not use washing powders or other substances containing abrasives as these may scratch the glass. 5) Do not sit or stand upon horizontal glass surfaces. 6) In order to maintain a high quality finish, when cleaning wooden panels please use a soft cloth with a suitable furniture polish if required. 7) Alphason Designs uses real wood veneers, consequently slight colour and pattern variation may occur and does not indicate a product defect. With natural wood, exposure to direct sunlight can produce colour change and should be avoided. Any slight change in colour over time does not indicate a product defect. Please Note: Maximum load for the glass shelves is 70Kg each. This support must be assembled in accordance with these assembly instructions. Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.

Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955

www.alphasondesigns.com

issue 01 12/06 181758


TOP OF UNIT.

1. A

FLAT FACE.

STAGE 1 • Place one side panel A on its rear edge. Place chrome washer G either side of the side panel A . With screw H attach support bar E . • DO NOT FULLY TIGHTEN SCREW

H E

G

H

AT THIS STAGE.

EACH SUPPORT BAR HAS A FLAT FACE. ENSURE THE FLAT FACE IS FACING THE TOP OF THE UNIT AS SHOWN.

STAGE 2

2.

• Place the second side panel other side of support bar

on its rear edge. Attach

with screw

• Be sure to place chrome washer panel A .

A

E

E

A

G

• DO NOT FULLY TIGHTEN SCREW

G

H

H

.

either side of side

H

AT THIS STAGE.

• Repeat this method in order to attach all other support bars E , once again ensuring the flat faces are positioned correctly.

3.

STAGE 3 • Once all the bars have been attached please fully tighten all screws H with allen key I . • Fit all cover caps hand.

F

into screws

H

and tighten by

• Be sure not to over tighten F as you may need to periodically tighten the screws H .

F

• Place stand into its upright position.

F

4.

M

STAGE 4 • Remove self adhesive clear buffer M from backing and carefully position three equally along each rod on the flat face.

TOP OF UNIT

M

X18

ENSURE ALL SUPPORT BARS FLAT FACES ARE FACING THE TOP EDGE AS SHOWN. issue 01 12/06 181758


STAGE 5

5.

• Place carefully the glass shelves B , C and D onto support bars ensuring the glass shelves rest on clear buffers M . • Ensure rear of all glass shelves align with rear of side panels as shown below. • This will help with the correct installation of cable tidy.

B

6.

SIDE VIEW.

STAGE 6

K

L

• Remove protective covering before assembly

K

.

• Remove backing from one side only of the self adhesive pad L and attach to rear of angle bracket K . Repeat this and attach adhesive pad L to the underside of the angle bracket K as shown.

L

• Repeat this step for the second angle bracket

! STAGE 7

BEFORE PROGRESSING TO STAGE 7, IT IS ADVISABLE TO CLEAN CURVED AREAS AT THE BACK OF THE GLASS SHELVES WITH AN ALCOHOL BASED CLEANER TO ENSURE A SECURE FIX OF THE CABLE TIDY.

K

7.

.

J

• Using one of the angle brackets K remove the backing off self adhesive pad L on the back section. Attach to top of cable tube J as shown.

K

• Remove backing off self adhesive pad on the underside of angle bracket K .

J

D K

• Attach cable tidy J and bracket K to centre of cut out section on top of glass shelf D .

8.

STAGE 8 • Unpeel backing off both self adhesive pads on remaining angle bracket K .

K

• Attach to bottom glass shelf

B

B

and cable tube

J

.

• Your stand is complete.

issue 01 12/06 181758


MODEL: ASP900-W, LO & B CERTIFICATE OF CONFORMITY C O M P O N ENT

A

DESCRIPTION

QTY

SIDE PANELS

2

PACKED BY

WALNUT - 200300 LIGHT OAK - 200299 BLACK - 200298

B

LARGE BOTTOM GLASS SHELF

1 141135

C

MEDIUM MIDDLE GLASS SHELF

1 141134

D

SMALL TOP GLASS SHELF

1 141133

E

6

SUPPORT BAR 402900

F

12

COVER CAPS 202278

G

24

CHROME WASHER 202279

H

SCREW

I

ALLEN KEY

12 1 202287

J

CABLE TIDY TUBE

1 403540

K ANGLE BRACKET FOR CABLE TUBE

2

(REMOVE PROTECTIVE COVERING BEFORE ASSEMBLY)

L

4

SELF ADHESIVE PAD 202275

M

18

CLEAR BUFFER 202277

issue 01 12/06 181758


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.