COFFEE TABLE
MODEL: ASPT- G, W, LO & B
ASSEMBLY INSTRUCTIONS
IMPORTANT INFORMATION! 1) Before starting assembly please take time to familiarise yourself with the instructions and the components listed on the back page, as this product could be unstable if incorrectly installed. 2) Do not place hot or cold items against or in close proximity to any glass surface unless an adequately thick insulating material is used to prevent such items coming into contact with the glass. 3) Do not strike the glass with hard or pointed items. 4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary; do not use washing powders or other substances containing abrasives as these may scratch the glass. 5) Do not sit or stand upon horizontal glass surfaces. 6) In order to maintain a high quality finish, when cleaning wooden panels please use a soft cloth with a suitable furniture polish if required. 7) Alphason Designs uses real wood veneers, consequently slight colour and pattern variation may occur and does not indicate a product defect. With natural wood, exposure to direct sunlight can produce colour change and should be avoided. Any slight change in colour over time does not indicate a product defect. Please Note: Maximum load for the glass shelves is 70Kg each. This support must be assembled in accordance with these assembly instructions. Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this coffee table.
Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955
www.alphasondesigns.com
issue 01 04/07 181759
STAGE 1
1.
TOP OF UNIT.
E
• Place one side panel
A
on its bottom edge on a clean flat surface to avoid any damage. Place chrome washers G either side of the side panel A shown in Fig 1a. With screw H attach support bar E .
• Attach remaining 3 support bars the same way.
to side panel
A
in
• EACH SUPPORT BAR HAS A FLAT FACE. ENSURE
G
H
F A
THE FLAT FACE IS FACING THE TOP OF THE UNIT AS SHOWN. • Fit all cover caps
FLAT FACE.
H
F
into screws
H
and tighten by hand.
2.
G
G
1a.
G
E
STAGE 2
• Place side panel
A
with the four support bars
attached flat onto a clean surface to avoid any damage.
• Place four chrome washers support bars
3.
G
on the ends of the four
F H G
A
A
STAGE 3 • Place second side panel A onto support bars E ensure the chrome washers G are correctly located into the holes in side panel A . • Attach remaining chrome washers G , screws caps F onto all four support bars.
H
and cover
issue 01 04/07 181759
4.
STAGE 4
D
• Remove self adhesive clear buffer D from backing and carefully position three equally along each rod on the flat face.
TOP OF UNIT
D
ENSURE ALL SUPPORT BARS FLAT FACES ARE FACING THE TOP EDGE AS SHOWN.
X12
5. STAGE 5 • Place carefully the glass shelves B and C onto support bars ensuring the glass shelves rest on clear buffers D .
B
Congratulations your coffee table is complete!
issue 01 04/07 181759
MODEL: ASPT- G, W, LO & B CERTIFICATE OF CONFORMITY C O M P O N ENT
QTY
DESCRIPTION
A
SIDE PANELS
PACKED BY
2 WALNUT - 200312 LIGHT OAK - 200311 BLACK - 200310 GLASS - 141145
B
LARGE BOTTOM GLASS SHELF
1 141147
C
SMALL TOP GLASS SHELF
1 141146
D
12
CLEAR BUFFER 202290
E
4
SUPPORT BAR 402905
F
8
COVER CAPS 202291
G
16
CHROME WASHER 202292
H
SCREW
I
ALLEN KEY
8 1
GLASS SCREW KIT -202289 WOODEN SCREW KIT - 202293
issue 01 04/07 181759