ASSEMBLY INSTRUCTIONS
!
THIS STAND REQUIRES 2 PEOPLE FOR ASSEMBLY.
IMPORTANT INFORMATION! 1) Before starting assembly please take time to familiarise yourself with the instructions and the components listed on the back page, as this product could be unstable if incorrectly installed. 2) Do not place hot or cold items against or in close proximity to any glass surface unless an adequately thick insulating material is used to prevent such items coming into contact with the glass. 3) Do not strike the glass with hard or pointed items. 4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary; do not use washing powders or other substances containing abrasives as these may scratch the glass. 5) Do not sit or stand upon horizontal glass surfaces. 6) In order to maintain a high quality finish, when cleaning wooden panels please use a soft cloth with a suitable furniture polish if required. 7) Alphason Designs uses real wood veneers, consequently slight colour and pattern variation may occur and does not indicate a product defect. With natural wood, exposure to direct sunlight can produce colour change and should be avoided. Any slight change in colour over time does not indicate a product defect.
PLEASE NOTE OTHER TOOLS REQUIRED: CROSS-HEAD SCREWDRIVER
Please Note: Maximum load for the top glass shelf is 95Kg. This support must be assembled in accordance with these assembly instructions. Maximum load for middle glass shelf is 20kg. Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.
Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955 info@alphasondesigns.com
www.alphasondesigns.com
issue 01 06/07
1.
STAGE 1
R
• Attach castors S using screws R , into corresponding holes in the underside of base panel A . 2 castors have a brake facility, ensure these are fitted in the best positions for ease of operation.
S
A
• Alternatively attach furniture glides O using screws N , into corresponding holes in the underside of base panel A .
OR N
O
A
2.
STAGE 2
B
• Place top glass panel B on it’s edge on a clean flat surface. • Fit conical plastic washers K onto top caps I . • Assemble tubes G , plastic washers J and top cap assemblies ( I and K ) on to glass panel B . Tighten by hand. • Assemble threaded rod H through hole in glass panel B into remaining top cap assembly.
J K I
G H
3.
STAGE 3
H C B
F
• Place top glass panel assembley from stage 2 upside down on a clean flat surface as shown. • Place top block
C
over threaded rod
H
.
• Insert dowels F into corresponding holes in top block C .
issue 01 06/07
4.
STAGE 4
F
• Locate middle glass shelf block C .
D
E
over dowels
• Fit bottom block D over threaded rod onto dowels F .
E
• Fit remaining 2 dowels
C
!
in top
and locate
into bottom block
D.
PLEASE TAKE CARE AT THIS STAGE AS MIDDLE GLASS SHELF IS NOT YET SECURE.
5.
STAGE 5 • Carefully locate base panel A over threaded rod tubes G and dowels F .
F
H
F
M
H,
• Fit washers M and nuts L over the tube ends G and threaded rod H . Use spanner P to tighten nuts L . TAKE CARE NOT TO OVERTIGHTEN NUTS.
L A F
G
H
• Once fully assembled, position the unit onto it’s castors/glides. DUE TO THE WEIGHT OF THIS UNIT 2 PEOPLE ARE REQUIRED FOR THIS STEP.
Congratulations your stand is complete! Self adhesive rubber pads Q are supplied to prevent TV movement on top glass shelf if required.
issue 01 06/07
MODERNA AV SUPPORT
MODELS: MD1300-LO, MD1300-W and MD1300-BV CERTIFICATE OF CONFORMITY C O M P O N ENT
DESCRIPTION
QTY
A
BASE PANEL
1
B
TOP GLASS PANEL
1
C
TOP BLOCK
1
D
BOTTOM BLOCK (Taller than block C )
1
E
MIDDLE GLASS SHELF
1
F
DOWELS
4
G
TUBES
2
H
THREADED ROD
1
I
TOP CAP
3
J
PLASTIC WASHER
2
K
CONICAL PLASTIC WASHER
PACKED BY
3 issue 01 06/07
MODERNA AV SUPPORT
MODELS: MD1300-LO, MD1300-W and MD1300-BV CERTIFICATE OF CONFORMITY C O M P O N ENT
DESCRIPTION
QTY
L
NUT
3
M
WASHER
3
N
GLIDE SCREW
6
O
FURNITURE GLIDES
6
P
Q
SPANNER
SELF ADHESIVE RUBBER PADS
PACKED BY
1
6
R
CASTOR SCREW
24
S
CASTOR
6
issue 01 06/07