Meters & Accessories
Engineering Data: 400-10
www.lcmeter.com
Table of Contents Description Page Number Table of Contents.......................................................................... 2 General ......................................................................................... 3 Meter Models ................................................................................ 4 Model Numbering System ............................................................ 5 Class Descriptions (Applications) ................................................. 6 Factors Affecting Materials of Construction .................................. 7 & 8 Viscosity ....................................................................................... 9 Pressure Loss vs.Viscosity ........................................................... 10 Maximum Flow Rate vs. Viscosity ................................................ 11 Kinematic Viscosity Conversion Chart .......................................... 12 Viscosity of Common Liquids ........................................................ 12 Meter Materials of Construction .................................................... 13 - 34 Chemical Composition of Metals .................................................. 35 Conversions ................................................................................. 36 & 37 Coefficients of Expansion ............................................................. 37 National Electrical Code (NEC) Ratings ........................................ 38 International Protection (IP) Ratings ............................................. 39 Corrosion Data ............................................................................. 40 - 51
2
General cating motion within the device permits extremely close and consistent tolerances within the LC Meter.
The LC Meter consists of a housing in which three rotors turn in synchronized relationship within three cylindrical bores with no metal-to-metal contact within the meter element. Each rotor is supported on either end by a bearing plate through which the rotor shafts protrude.
Because the dynamic force exerted by the product flowing through the meter is at right angles to the faces of the displacement rotors, and because the meter is designed so that the rotor shafts are always in a horizontal plane, there is no axial thrust. Therefore, the rotors automatically seek the center of the stream between the two bearing plates thereby eliminating wear between the ends of the rotors and the bearing plates.
The bladed displacement rotors, alternately move through the two half-cylinder bores of the meter element, while the single blocking rotor rotates within its bore in such a way as to produce a continuous capillary seal between the unmetered, upstream product and the metered, downstream product.
The oversize design of the sleeve bearings, as well as the specially selected materials from which they are made, assure maximum throughput before bearing replacement is required.
At one end of each rotor shaft is a timing gear. The blocking rotor gear, having twice the number of teeth of each of the displacement rotor gears, rotates at half the RPM of the displacement rotors.
As a result the LC Meter provides unequalled accuracy, long operating life and exceptional dependability.
Throughout the meter element the mating surfaces are either flat surfaces or cylindrical faces and sections that are most accurately machined. No oscillating or recipro-
Accuracy / Performance area in shear and the smooth flowing characteristics of the LC Meter the standard LC design has accurately metered product from 30 SSU (1 centipoise) to 1,500,000 SSU (325,000 centipoise).
Superior Accuracy at constant flow: With all other conditions being constant, the LC Meter is capable of 0.05% or better in repeatability over entire flow range. Accuracy over the widest range of flow: The LC Meter has a most ideal combination of minimum seal or slippage area with lowest pressure differential across this seal. This results in superior accuracy over a wide range of flow rates.
Repeatability: Mech. registration: capable of 0.05% (±0.025%) of reading over entire range Elect. registration: capable of 0.03% (±0.015%) of reading over entire range
Linearity: Over 5:1 range Mech. registration: capable of ± 0.125% or better from max. nom. flow rate Elect. registration: capable of ± 0.10% or better from max. nom. flow rate
Sustained accuracy over time: No wear from metalmetal contact within the measuring chamber . . . means no wear . . . no wear means no increase in clearances . . .no increase in clearances means no increase in slippage . . . and no increase in slippage means no deterioration in accuracy.
Over 10:1 range Mech. registration: capable of ± 0.22% or better from max. nom. flow rate Elect. registration: capable of ± 0.10% or better from max. nom. flow rate Over 40:1 range Mech. registration: capable of ± 0.5% or better for max. nom. flow rate Elect. registration: capable of ± 0.15% or better from max. nom. flow rate
Accuracy over a pressure range: Because of the LC Meter’s unique dual-case design, the bearing surfaces of the meter element are internally and externally subjected to the same system pressure. Therefore, the meter element cannot be stretched or distorted, causing changes in seal area that would adversely affect accuracy.
Note: Stated accuracy obtainable when all variables remain constant. Reading/measurements reflect a minimum of one minute of flow at selected rate(s). All accuracy statements based on metering safety solvent (aliphatic hydrocarbon), approximate viscosity 1 CPS. On higher viscosity products, the average deviation in accuracy will be less.
Accuracy over a temperature range: Due to the common coefficients of expansion of the critical parts of the LC Meter element, products can be metered accurately from -40°F (-40° C) to +160°F (+71° C). Ripid thermal shock (temperature changes in excess of 40°F) should be avoided.
Regulatory: Meets NIST and other international weights & measures accuracy requirements. Meets performance requirements of USA Military Specifications.
Accuracy over a viscosity range: Due to the minimum
3
Meter Models Liquid Controls PD Meters METER MODELS Listed in order of Maximum Nominal Flow Rates. Consult LC PD Product Overview # 100-10 for product application and material class
recommendations. Maximum Non-Shock Working Pressure (PSI) ratings are based on products at temperatures below 160°F (71°C). See page 7 for working pressure vs. temperature data.
Maximum Nominal
150 PSI
275 PSI
300 PSI
350 PSI
740 PSI
Standard
Primary
Material Classes
10.3 BAR
19 BAR
21 BAR
24 BAR
51 BAR
102 BAR
Flange Size*
Material
Available
1034 kPa
1896 kPa
2068 kPa
2413 kPa
5102 kPa
10204 kPa
Flow Rate GPM
L/min
30
113
1 1/2"
Aluminum
10
60
227
1 1/2"
Aluminum
1, 2, 3, 4, 10, 14, 16, & 30
2" Optional
Stainless Steel
8
M-5
100
380
2"
Aluminum
1, 2, 3, 4, 10, 14, 15, & 16
M-7
MA-4+
1 1/2" Optional Stainless Steel Cast Iron
M-5
M-5**
MA-5+
M-7**
MA-7+
8 M-7 7, 27, & 37
M-7
M-7**
20 M-7
M-7**
2"
Brass
2"
Steel
1, 2, 7, 10, 14, 16 & 37
MS-7
MSAA-7
M-10
M-10**
150
550
2"
Aluminum
1&2
200
757
3"
Aluminum
1, 2, 3, 4, 10, 14, 15, & 16
M-15
M-15**
3"
Steel
1, 2, 10, 14 & 16
MS-15
MSAA-15***
3"
Stainless Steel
8
Aluminum
1, 2
300
1,136
3"
350
1,325
4"
450
1,700
1,480 PSI
MSA-7
MSB-7
MSC-7
MSA-15
MSB-15
MSC-15
MSA-30
MSB-30
MSC-30
MSA-75
MSB-75
MSC-75
MSB-120
MSC-120
MA-15+
MSAA-15*** M-25
3" Optional
Aluminum
1, 2, 3, 4, 14, 15 & 16
M-30
3"
Cast Iron
7, 27, 37 & 47
M-30
3"
Steel
1, 2, 10, 14 & 16
MS-30
3"
Stainless Steel
8
M-25**
MSAA-30*** MSAA-30***
4"
Aluminum
1&2
M-40
3"
Steel
1&2
MS-40
600
2,271
4" 6" Optional
Aluminum
1, 2, 3, 14 & 15
M-60
M-60**
700
2,650
4"
Steel
1, 2, 10 & 14
MS-75
MSAA-75***
800
3,000
6" 4" Optional
Aluminum
2
M-80^
M-80**
1,000
3,785
6"
Steel
1, 2, 10 & 14
MS-120
MSAA-120*** MSA-120
6"
Stainless Steel
8
MSAA-120***
* Flanges: All standard M-Series meters are supplied with choice of threaded NPT and BSPT companion flanges, or slip-on weld companion flanges. MA-Series meters are supplied with threaded NPT companion flanges. All MS-Series steel case meters are supplied standard with ANSI flanged connections; DIN optional. Reducing flanges are available for all steel case meters. ** 275 PSI working pressure available for meter only. ***285 PSI, 19.7 BAR, 1965 kPa for MSAA-15, 30, 75 & 120 meters. + MA-Series meters are all UL Listed for LPG. ^ M-80 meter capable of momentary overload operation at 125% of maximum rated capacity in either direction (applies to Class 2 meters only, on jet fuel only). 125% overload operation (1,000 GPM) requires 6” ANSI or 6” Victaulic connections.
4
Model Numbering System Model number coding description MSA-7-A-10
Meter Type M = meter
Case Material Blank = other than steel S = steel case
Working Pressure Blank = 150 psi AA = 285 psi A = 350 psi B = 720 psi C = 1440 psi
4 = 30 gpm 5 = 60 gpm 7 = 100 gpm 10 = 150 gpm
Meter Size 15 = 200 gpm 25 = 300 gpm 30 = 350 gpm 40 = 450 gpm
60 = 600 gpm 75 = 700 gpm 80 = 800 gpm 120 = 1000 gpm
Accessory Configuration A, C, I, K (see chart below)
Construction Application Class 1, 2, 3, 10 etc. (see table on p. 6)
Standard accessory configurations A, C, I, K M / MA - 7 - A A = Meter with counter
Optional Accessories: Printer, Strainer
M / MA - 7 - I I = Meter with counter, preset counter and preset valve
M / MA - 7 - C C = Meter with counter, strainer and air eliminator
Optional Accessories: Printer
Optional Accessories: Printer, Strainer
M / MA - 7 - K K = Meter with counter, preset counter and preset valve, strainer and air eliminator
Optional Accessories: Printer
Mounting arrangements LC meters may be mounted in a varity of configurations, as shown below. Do not position the meter on its side, i.e., with cover plate face down or up.
*
* ONLY AVAILABLE ON DIRECT MOUNT PULSER MODELS OR MODELS LESS RESET COUNTER. Note: regardless of meter mounting configurations, accessories such as the air/vapor eliminator must always be mounted in a vertical orientation to permit proper operation of the float-actuated apparatus.
5
Class Descriptions (Applications) Class 15 For metering oil or water base latex products, polyester resins, and adhesives (neutral pH). Also available for metering herbicides and nitrogen fertilizer solutions (requires viton and PTFE seals). Operation at 80% of rated capacity or less is recommended. Shear sensitive liquids must be operated at 1/3 of rated capacity or less.
Class 1 For metering refined petroleum products such as leaded and unleaded gasoline, fuel oils, diesel fuel, kerosene, ethylene glycol, (antifreeze), and propylene glycol at rated capacity. Also used on motor oils, crop oils and rotogravure ink at reduced rates of flow. Class 2 For metering aviation gasolines and jet fuels when meter is installed downstream of the filter/separator. Non-ferrous construction ... meters may be operated at rated capacity.
Class 16 For general solvent metering service such as: methanol, toluene, xylene, naphtha, acetone, MEK, MIBK, and alcohols including ethanol (also 200-proof alcohol). Meters may be operated at rated capacity, except for continuous duty service. Class 7 meters should be used if the application involves the use of chlorinated solvents.
Class 3 For metering a wide variety of products such as liquid sugars, corn syrup, corn sweetners, dextrose, fructose, sucrose, maltose, lactose, corn oil, soy bean oil, cotton seed oil, coconut oil, and shortening’s etc. Rate of flow is based on viscosity to pressure loss relationship.
Class 20 For batch process water meter service. Not intended for use with deionized or demineralized water. May be used for solvents and other liquids compatible with brass. Meters may be operated at rated capacity. Not intended for continuous duty service. All brass construction with 300 series stainless steel trim.
Class 4 For metering treated waters (deionized, demineralized, and potable), and certain solvents where no red metals are allowed. Meters may be operated at rated capacity, except for continuous duty service. NOTE: substitute for former class 6 and 17 applications. Anodized aluminum and stainless steel construction.
Class 27 For metering alkaline pH latex products and adhesives, and some clear liquid fertilizers (10-34-0). Operation at lower than rated capacity is recommended. Shear sensitive liquids must be operated at 1/3 of rated capacity or less. All ferrous construction.
Class 7 For metering chlorinated solvents such as: perchloroethylene, trichloroethylene, trichloroethane, and methylene chloride. Also used for general solvent service. Meters may be operated at rated capacity, except for continuous duty service. All ferrous construction.
Class 30 For metering herbicides such as Aatrex, Atrazine, Bicep, Bladex, Dual, Lasso, Lasso ME, Treflan, Sutan, Sutazine, and Eradicane (requires PTFE seals). Operation at up to 80% of maximum rated capacity is recommended. Available in M-5 meter only. Use class 15 in all other meter sizes.
Class 8 For metering acid pH liquids such as: nitric, phosphoric, and glacial acetic acids, amines, citric (fruit juices) and vinegars. All 316 stainless steel construction. Operation at up to 80% of maximum rated capacity is recommended.
Class 37 For metering sodium hydroxide (caustic) solutions, high sulfur crude oil (LACT and NOD), and other alkaline pH liquids including non-abrasive asphalt emulsions, liquid feed (molasses) supplements, and some resins. Construction suitable for heated and/or viscous liquids. Rate of flow based on viscosity to pressure loss relationship. All ferrous construction.
Class 10 For metering liquified petroleum gas (LPG) including butane, isobutane, pentane, ethane, freons, and propane. NOTE: materials of construction (including seals) are UL approved for propane, modifications to materials of construction may be required for other liquids listed, including commercial grade NH3.
Class 47 For metering mildly abrasive liquids, all ferrous construction. Consult Customer Service at the factory for all applications.
Class 14 For metering crude oil (LACT and NOD). Also for heated and/or viscous liquids including animal fats, resins, #6 oil and non-abrasive asphalt emulsions. Rate of flow based on viscosity to pressure loss relationship. NOTE: Substitute for former class 5 applications.
6
Factors Affecting Meter Materials and Meter Ratings 1. Temperature
M-Series (M5 & M7: Cast Iron or Stainless Steel)
Temperature is an important application parameter that may have the following effects on meter performance: An increase in product temperature may increase the corrosion rate of meter materials. Product temperature may determine seal materials. Maximum system temperature may affect (decrease) the pressure rating of the meter.
Product Temp. 150°F 200°F 250°F 300°F
Pressure* 150 psi 100 psi 75 psi 50 psi
Refer to the information below to assess the effects of temperature on meter materials and ratings.
MA-Series Product Temp. 150°F 200°F 250°F 300°F
Pressure* 350 psi 275 psi 250 psi 150 psi
MS-Series Product Temp. 150°F 200°F 250°F 300°F 400°F
Pressure* 140 psi 130 psi 120 psi 115 psi 100 psi
MSA-Series Product Temp. 150°F 200°F 250°F 300°F 400°F
Pressure* 280 psi 260 psi 245 psi 230 psi 215 psi
Product temperature range for seals Seal Material Buna-N Viton®-A P.T.F.E Kalrez Buna-N cork (gasket) Neoprene rubber Silicone rubber
Temp. Range -65°F to +250°F -20°F to +400°F -450°F to +500°F +5°F to +500°F -30°F to +450°F -65°F to +300°F -80°F to +450°F
Meter pressure rating at elevated temperatures
M-Series (M5, M7, & M10: Aluminum only) Product Temp. 150°F 200°F 250°F 300°F
Pressure* 350 psi 275 psi 250 psi 150 psi
MSAA-Series Product Temp. 150°F 200°F 250°F 300°F 400°F
M-Series (M15 and above) Product Temp. Pressure* 150°F 150 psi 200°F 100 psi 250°F 75 psi 300°F 50 psi
Pressure* 255 psi 240 psi 225 psi 210 psi 180 psi
For MSB and MSC Series meters, consult the factory.
2. Product lubricity A large factor in selecting bearing materials is the lubricity of the product. Examples of low lubricity products include LPG, gasoline, and water. Consult factory for details.
Viton® are registered trademarks of DuPont Corp. * Maximum Non-Shock Working Pressure M-Series meters are nameplated at 150 psi non-shock working pressure, and should not be applied beyond ratings without factory approval.
7
Factors Affecting Meter Materials and Meter Ratings 3. pH - Hydrogen-lon concentration
4. Galvanic corrosion
An excellent indicator of the corrosivity of a solution is its pH factor. A pH scale is derived from the hydrogen-ion concentration and is a measure of the relative acidity or alkalinity of a solution. See table below.
Similar metals are compatible; dissimilar metals are not. When dissimilar metals contact in the presence of an electrolyte, a galvanic action occurs which causes one of the metals to corrode at a much faster than normal rate, while the other corrodes more slowly, if at all. The rate, location and extent of the corrosion depends on three factors: the difference in electrical potentials the conductivity of the corroding medium the relative sizes of the contacting areas.
pH SCALE 7 = NEUTRAL 0
1
2
3
4
5
6
8
INCREASED ACID REACTION
9
10
11
12
13 14
INCREASED ALKALINE REACTION
The avoidance of dissimilar metals and/or the use of a sacrificial anode will reduce galvanic corrosion.
7
Galvanic series Anodic or active
It is difficult to generalize about the resistance of metals to corrosion in liquids of various pH levels, due to numerous factors such as: The actual chemical makeup of the solution (which ions are present). Whether or not oxygen is present. Whether or not concentration cells may form, etc.
Cathodic or Noble
However, the following metals have generally been found to be resistant in the ranges indicated:
Metal Magnesium Zinc Aluminum Cadmium Steel, Cast Iron Brasses Copper Bronzes Monel Nickel Stainless steel
5. Concentration Material Aluminum Cast Iron Treated cast iron Ni-Resist Stainless steel
The increase or decrease in concentration of some products will increase corrosion rates.
pH 5-8 5.5 - 11 3.5 - 8 5.5 - 14 0 - 14
6. Abrasives Abrasives are erosive. They are a factor in selecting meter construction materials. Class 47 meters are generally recommended. Consult factory for details.
7. Products that air harden, temperature harden, crystallize, etc.
This chart is intended as a general guide only, and should not be interpreted as specific meter application data. In some instances operation outside these ranges may be possible but the factory should be consulted before proceeding.
Appropriate meter protective measures must be taken to ensure the product remains in a liquid state at all times or is properly flushed during idle periods with a medium compatible with meter materials of construction.
Due to varying degrees of concentration, temperature, etc., we reserve the right to make an evaluation before final recommendations are given or orders are accepted.
8. Liquified gases Knowledge of operating pressure and temperature is essential in supplying a meter with the correct pressure rating.
9. Inhibitors Many products which are considered normally corrosive can be rendered partially or fully noncorrosive by the addition of inhibitors. Obtaining this information will be very useful in selecting meter materials.
8
Viscosity Viscosity is the property of a fluid that is a measure of its resistance to flow. Consideration of viscosity over the temperature range of meter operation is important in determining maximum meter flow rate, pressure loss, and
bearing material selection. The tables below provide viscosity vs. temperature data for selected petroleum products.
9
Pressure Loss vs. Viscosity When metering a liquid, the pressure loss through the meter will increase as viscosity increases. The pressure loss data shown in the graph to the right is based on metering Stoddard solvent with viscosity of approximately 30 SSU (1 centistoke).
Average meter pressure drop vs. flow rate for M60 Meter.
Calculating Pressure Loss on Higher Viscosity Liquids A Conversion Factor graph may be used to determine the pressure drop on higher viscosity products. The Conversion Factor graph for determining pressure loss as viscosity increases is approximate only. However, the data is acceptable when preparing specifications for most metering systems. The pressure loss through a strainer or faucet valve will be approximately the same as the pressure loss through the equivalent size meter.
Conversion Factor Graph
How to use Conversion Factor Graph to determine Pressure Loss vs. viscosity The graph (Average Meter Pressure Drop vs. Flow Rate) is based on the use of an LC Meter on safety solvent with a viscosity of 30 SSU. To determine the pressure drop of a liquid with a higher viscosity, multiply the pressure drop as indicated for safety solvent (at whatever % of flow rate is involved) by the conversion factor that applies from graph to the right. For example: If the meter is to be operated at 100% of capacity, the pressure drop for safety solvent would be 2.3 psi. If the liquid to be metered has a viscosity of 1,000 SSU the conversion factor would be 3.2 (approximate) and the pressure loss would be calculated as 2.3 psi x 3.2 or 7.36 psi.
10
Maximum Flow Rate vs. Viscosity Meter Flow Rate Limit (% of Rated Flow Vs. Viscosity) Use the chart below to determine maximum meter flow rate relative to meter bearing material and product viscosity. First,determine the percent of rated capacity at which the meter will be required to operate. Second, determine product viscosity at system operating temperature. Third, plot the point on the chart, below, where the two lines intersect. Fourth, identify the meter bearing material from the Meter Materials of Construction tables starting on page 13 and locate the corresponding slope on the chart below. If the plotted point is above the bearing material slope, you are outside the allowable pressure loss for the specified meter and bearing. You should either choose a larger meter, reduce flow rate or consider alternative bearing materials.
11
Kinematic Viscosity Conversion Chart Kine m a tic Viscosity Conve rsion Chart SSU SSU SSU SSU Centistoke Centistoke Centistoke Centistoke Saybolt Saybolt Saybolt Saybolt Seconds Universal Seconds Universal Seconds Universal Seconds Universal 1 31 240 1200 1300 6100 7500 35000 2 34 260 1280 1400 6480 8000 37000 4 38 280 1380 1500 7000 8500 29500 7 47 300 1475 1600 7500 9000 41000 10 60 320 1530 1700 8000 9500 43000 15 80 340 1630 1800 8500 10000 46500 20 100 360 1730 1900 9000 15000 69400 25 150 380 1850 2000 9400 20000 92500 30 160 400 1950 2100 9850 30000 13860 40 210 420 2050 2200 10300 40000 185000 50 260 440 2160 2300 10750 50000 231000 60 320 460 2270 2400 11200 60000 277500 70 370 480 2380 2500 11600 70000 323500 80 430 500 2480 3000 14500 80000 370000 90 480 550 2660 2500 16500 90000 415500 100 530 600 2900 4000 18500 100000 462000 120 580 700 3380 4500 21000 125000 587000 140 690 800 3880 5000 23500 150000 694000 160 790 900 4300 5500 26000 175000 810000 180 900 1000 4600 6000 28000 200000 925000 200 1000 1100 5200 6500 30000 220 1100 1200 5620 7000 32500
Viscosity of Common Liquids Liquid Corn Oil Cotton Seed Oil Crankcase Oil - SAE 10W Crankcase Oil - SAE 20W Crankcase Oils - SAE 20 Crankcase Oils - SAE 40 Crankcase Oils - SAE 60 Crude Oils Fuel oil # 1 Fuel oil # 2 Fuel oil # 3 Fuel oil # 5 Fuel oil # 6 Gasoline Glycerine (100%) Jet Fuel Kerosene Linseed oil Turpentine Water, distilled
Viscosity SSU CentiStokes 135 28.7 176 37.9 5000-10000 1100-2200 10000-40000 2200-8800 240-400 51.9-86.6 580-950 125-206.6 1600-2300 352-507 40-783 4.28-169.5 34-40 2.39-4.28 36-50 3.0-7.4 35-45 2.69-5.84 50-125 7.4-26.4 175-780 37.5-172 0.88 2,950 648 52 7.9 35 2.71 143 30.5 1425 86.5-95.2 31 1.00
12
Temp 째F 130 100 0 0 100 100 100 60 70 70 70 70 160 60 68.6 -30 68 100 100 68
째C 54.4 37.8 -17.8 -17.8 37.8 37.8 37.8 15.6 21.1 21.1 21.1 21.1 71.1 15.6 20.3 -34.4 20 37.8 37.8 20
13
L1106
Rotor
Blocking
Drive
518 Alum
316 SS
17.4 pH SS
17.4 pH SS
17.4 pH SS
17.4 pH SS
316 SS
or none
316 SS
or none
316 SS
Iron/
Sintered
Gears
Internal
L1131
360 Alum
Covers
Buna-N
Seals** Adjuster
Mechanical
360 Alum
Anodized
360 Alum
Anodized
Buna-N
UL Approved
Buna-N
UL Approved
Standard
Standard
1 1/2" NPT
Buna-N
356 Alum Andz
360 Alum Andz
1 1/2" NPT
Buna-N
356 Alum Andz
(if required)
& Elbows
Flanges
Standard
Hardcoat
316 SS
316 SS
Hardchrome
316 SS
17.4 pH SS
316 SS
17.4 pH SS
316 SS
or none
316 SS
or none
Anodized
Anodized
solutions.
nitrogen
Herbicides &
356 Alum
30
L1230
(not chlorinated).
solvent service
For general
356 Alum
16
L1617
both.
products or
or viscous
oils, heated
For crude
Anodized
Alum/Carbon
Hardcoat
/Carbon
Ni-Resist II
14
L1151
/PTFE
Ni-Resist II
pH liquids.
356 Alum
Option
For acidic
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Red
518 Alum
"Red"
Anodized
518 Alum
Anodized
518 Alum
Anodized
Red
518 Alum
"Red"
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
17.4 pH SS
Iron
Sintered
Iron
Sintered
17.4 pH SS
Iron
Sintered
Iron
Sintered
or none
316 SS
or none
316 SS
Iron/
Sintered
or none
316 SS
Iron/
Sintered
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
316 SS
Steel
Stainless
300 Series
Steel
Stainless
316 SS
Anodized
360 Alum
Anodized
PTFE
UL Approved
Buna-N
UL Approved
Standard
Standard
Buna-N
1 1/2" NPT
Buna-N
356 Alum Andz
360 Alum Andz
1 1/2" NPT
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Viton
UL Approved
Buna-N
Viton
Standard
Standard
Hi Temp
Option
Standard
360 Alum Andz
1 1/2" NPT
Viton
356 Alum Andz
360 Alum Andz
1 1/2" NPT
Buna-N
356 Alum Andz
360 Alum Andz
1 1/2" NPT
Viton
356 Alum Andz
316 SS
1 1/2" NPT
PTFE
316 SS
/Carbon
L1490
316 SS
Anodized
Red
518 Alum
Hardchrome
360 Alum Andz 316 SS
Anodized
Red
518 Alum
Anodized
8
316 SS
Alum/Carbon
Hardcoat Anodized
waters.
316 SS
Anodized
For treated
356 Alum
4
Anodized
L1247
oils.
& vegetable
sweeteners
For liquid
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
360 Alum Andz 518 Alum
316 SS Hardchrome
Iron
Sintered
Rotor Gears
Displacement
356 Alum Andz
Ni-Resist II
Anodized
518 Alum
Iron
Sintered
Rotor Gear
3
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
or Alum
Hardchrome
316 SS
Journals
gasolines.
356 Alum
Anodized
Aviation
356 Alum
2
L1117
Hardcoat
or
Anodized
Anodized
Ni-Resist II
Hardcoat Anodized
products.
Anodized
petroleum
Refined
518 Alum
Rotors
Displacement
Standard
518 Alum
Rotor
Blocking
1
Ni-Resist II
Bearing (if required)
356 Alum
Housing
**Buna, Viton, or PTFE/Kalrez seals optional where compatible.
Application
Element*
Class
M-5 & P Meters
*Elements listed are standard for class. Options are application specific.
METER MATERIALS OF CONSTRUCTION - PD METERS & ACCESSORIES
14
Anodized
Anodized
Anodized
L2143
Anodized
adhesives.
Latex &
water based
For oil &
356 Alum
15
L2302
or both.
products
or viscous
oils, heated
Alum/PTFE
Hardcoat
Anodized
14
For crude
w/PTFE
Ni-Resist II
356 Alum
pH liquids.
Option
For acidic
316 SS
w/Carbon
316 SS
/Carbon
Ni-Resist II
Alum/Carbon
Hardcoat
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
L2491
8
pH liquids.
& alkaline
solvents
Chlorinated
L2360
7
waters.
Cast Iron
Anodized
For treated
356 Alum
4
L2242
oils.
vegetable
sweeteners &
For liquid
356 Alum
3
L2133
gasolines.
Aviation
356 Alum
2
L2122
products.
petroleum
Refined
356 Alum
1
Housing
L2102
Application
Element*
Class
M-7 Meters
Anodized
Red
518 Alum
Anodized
Red
518 Alum
"Red"
316 SS
Cast Iron
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Red
518 Alum
Anodized
Red
518 Alum
"Red"
316 SS
Cast Iron
Anodized
Red
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
416 SS
Iron
Sintered
316 SS
Iron
Sintered
416 SS
Ni-Resist II
Ni-Resist II
Iron
Sintered
Rotor Gear
17.4 pH SS
Iron
Sintered
coated
Armoloy
316 SS
Iron
Sintered
17.4 pH SS
Ni-Resist II
Ni-Resist II
Iron
Sintered
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
316 SS
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Anodized
360 Alum
Anodized
360 Alum
316 SS
Cast Iron
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Covers
UL Approved
Buna-N
Viton
PTFE
Viton
UL Approved
Buna-N
UL Approved
Buna-N
UL Approved
Buna-N
UL Approved
Buna-N
Seals**
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
2" NPT
Buna-N
356 Alum Andz
2" NPT
Viton
356 Alum Andz
2" NPT
PTFE
316 SS
2" NPT
Viton
Cast Iron
2" NPT
Buna-N
356 Alum Andz
2" NPT
Buna-N
356 Alum Andz
2" NPT
Buna-N
356 Alum Andz
2" NPT
Buna-N
356 Alum Andz
(if required)
Flanges
Standard
Buna-N
Anodized
356 Alum
Viton
356 Alum
PTFE
316 SS
Viton
Cast Iron
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
(if required
Strainer
Standard
15
Cast Iron
Cast Iron
Anodized
Anodized
Anodized
products.
petroleum
Refined
356 Alum
1
Housing
L3161
Application
Element*
Class
M-15 Meters
gasolines.
Aviation
356 Alum
2
L2802
products.
petroleum
Refined
356 Alum
1
Housing
L2801
Application
Element*
Class
M-10 Meters
crude oil.
High Sulphur
L2362
37
fertilizers.
liquid
& some
herbicides
For
L2361
27
water.
For general
L2340
20
(not chlorinated).
service
solvent
Brass
Anodized
For general
356 Alum
16
L2316
Ni-Resist II
Plates
Bearing
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Plates
Bearing
Ni-Resist II
/PTFE
Ni-Resist II
/Carbon
Brass
/Carbon
Ni-Resist II
M-7 Meters . . . Continued
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
"Red"
Cast Iron
"Red"
Cast Iron
"Red"
Brass
Anodized
Hardcoat
518 Alum
Anodized
518 Alum
Rotors
Displacement
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
"Red"
Cast Iron
"Red"
Cast Iron
"Red"
Brass
Anodized
518 Alum
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
Ni-Resist II
Iron
Sintered
Rotor Gear
Blocking
Iron
Sintered
Iron
Sintered
17.4 pH SS
Option
Delrin
Iron
Sintered
Nodular Iron
Rotor Gears
Displacement
coated
Armoloy
416 SS
Iron
Sintered
Rotor Gears
Displacement
Iron
Sintered
Iron
Sintered
Brass
Iron
Sintered
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Brass &
Steel
Stainless
300 Series
Anodized
360 Alum
Covers
Anodized
360 Alum
Anodized
360 Alum
Covers
Cast Iron
Cast Iron
Brass
Anodized
360 Alum
Buna-N
UL Approved
Buna-N
Seals**
UL Approved
Buna-N
UL Approved
Buna-N
Seals**
Viton
Viton
UL Approved
Buna-N
UL Approved
Standard
(if required)
Adjuster
Mechanical
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Standard
Standard
3" NPT
Buna-N
Cast Iron
(if required)
Flanges
Standard
2" NPT
Buna-N
356 Alum Andz
2" NPT
Buna-N
356 Alum Andz
(if required)
Flanges
Standard
2" NPT
Viton
Cast Iron
2" NPT
Viton
Cast Iron
2" NPT
Buna-N
Brass
2" NPT
Buna-N
356 Alum Andz
Buna-N
356 Alum
(if require
Strainer
Standard
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
(if require
Strainer
Standard
Viton
Cast Iron
Viton
Cast Iron
Buna-N
Brass
Buna-N
356 Alum
16
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
gasolines.
Aviation
356 Alum
2
L3252
products.
petroleum
Refined
356 Alum
1
Housing
L3255
Application
Element*
Class
M-25 Meters
(not chlorinated).
service
solvent
For general
356 Alum
16
L3167
adhesives.
Latex &
water based
For oil &
356 Alum
15
L3166
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L3165
waters.
For treated
356 Alum
4
L3164
oils.
vegetable
sweeteners &
For liquid
356 Alum
3
L3163
gasolines.
Aviation
356 Alum
2
L3162
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Plates
Bearing
/Carbon
Ni-Resist II
Alum/PTFE
Hardcoat
Ni-Resist II
Alum/Carbon
Hardcoat
Ni-Resist II
Ni-Resist II
M-15 Meters . . . Continued
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Hardcoat
518 Alum
Anodized
Red
518 Alum
Anodized
Red
518 Alum
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Anodized
518 Alum
Anodized
Red
518 Alum
Anodized
Red
518 Alum
Anodized
Red
518 Alum
Anodized
518 Alum
Anodized
518 Alum
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
Ni-Resist II
Ni-Resist II
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
316 SS
coated
Armoloy
Nodular Iron
316 SS
Option
Delrin
Ni-Resist II
Ni-Resist II
416 SS
coated
Armoloy
416 SS
coated
Armoloy
416 SS
Rotor Gears
Displacement
Nodular Iron
coated
Armoloy
316 SS
Nodular Iron
coated
Armoloy
316 SS
coated
Armoloy
416 SS
coated
Armoloy
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Anodized
356 Alum
Anodized
360 Alum
Covers
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Buna-N
UL Approved
Buna-N
UL Approved
Buna-N
Seals**
UL Approved
Buna-N
UL Approved
Buna-N
Viton
UL Approved
Buna-N
UL Approved
Buna-N
UL Approved
Standard
Standard
(if required)
Adjuster
Mechanical
Standard
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
3" NPT
Buna-N
356 Alum Andz
3" NPT
Buna-N
Cast Iron
(if required)
Flanges
Standard
3" NPT
Buna-N
Cast Iron
3" NPT
Buna-N
356 Alum Andz
3" NPT
Buna-N
Cast Iron
3" NPT
Buna-N
356 Alum Andz
3" NPT
Buna-N
356 Alum Andz
3" NPT
Buna-N
Cast Iron
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
(if require
Strainer
Standard
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
Viton
356 Alum
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
17
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
(not chlorinated).
service
solvent
For general
356 Alum
16
L3467
adhesives.
Latex &
water based
For oil &
356 Alum
15
L3494
products or both
or viscous
oils, heated
For crude
356 Alum
14
L3445
pH liquids.
& alkaline
solvents
Chlorinated
L3417
7
waters.
Cast Iron
Anodized
For treated
356 Alum
4
L3473
oils.
vegetable
sweeteners &
For liquid
356 Alum
3
L3436
gasolines.
Aviation
356 Alum
2
L3426
products.
petroleum
Refined
356 Alum
1
Housing
L3403
Application
Element*
Class
M-30 Meters
/Carbon
Ni-Resist II
Alum/PTFE
Hardcoat
Ni-Resist II
/Carbon
Ni-Resist II
Alum/Carbon
Hardcoat
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
Anodized
Hardcoat
356 Alum
Anodized
Red
356 Alum
Anodized
Red
356 Alum
Cast Iron
Anodized
Red
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
356 Alum
Anodized
Red
356 Alum
Anodized
Red
356 Alum
Cast Iron
Anodized
Red
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
coated
Armoloy
Nodular Iron
304 SS
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
304 SS
coated
Armoloy
Ni-Resist II
coated
Armoloy
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Nodular Iron
coated
Armoloy
304 SS
Nodular Iron
Nodular Iron
coated
Armoloy
304 SS
416 SS
416 SS
Nodular Iron
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Cast Iron
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Covers
Buna-N
Buna-N
Viton
Viton
Buna-N
Buna-N
Buna-N
Buna-N
Seals**
Standard
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
4" NPT
Buna-N
Cast Iron
4" NPT
Buna-N
356 Alum Andz
4" NPT
Buna-N
Cast Iron
ANSI
flat faced
3" 125#
4" NPT
Buna-N
356 Alum Andz
4" NPT
Buna-N
356 Alum Andz
4" NPT
Buna-N
356 Alum Andz
4" NPT
Buna-N
Cast Iron
(if required)
Flanges
Standard
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
Viton
356 Alum
Viton
Steel
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
(if require
Strainer
Standard
18
Cast Iron
Cast Iron
Cast Iron
Anodized
Anodized
Anodized
Anodized
Anodized
oils.
vegetable
sweeteners &
For liquid
356 Alum
3
L3501
gasolines.
Aviation
356 Alum
2
L3521
products.
petroleum
Refined
356 Alum
1
Housing
L3502
Application
Element*
Class
M-60 Meters
gasolines.
Aviation
356 Alum
2
L3484
products.
petroleum
Refined
356 Alum
1
Housing
L3477
Application
Element*
Class
M-40 Meters
abrasive liquids.
For mildly
L3447
47
crude oil.
High Sulphur
L3437
37
fertilizers.
& some liquid
herbicides
L3427
27
Ni-Resist II
Ni-Resist II
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Plates
Bearing
/Ceramic
Ni-Resist II
Ni-Resist II
/Rulon
Ni-Resist II
M-30 Meters . . . Continued
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
"Red"
Cast Iron
"Red"
Cast Iron
"Red"
Cast Iron
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
"Red"
Cast Iron
"Red"
Cast Iron
"Red"
Cast Iron
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
/Ceramic
303 SS
Hardchrome
316 SS
Hardchrome
coated
Armoloy
Ni-Resist II
coated
Armoloy
Ni-Resist II
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
TiN coated
Nodular Iron
coated
Armoloy
Nodular Iron
TiN coated
Nodular Iron
416 SS
416 SS
Nodular Iron
Rotor Gears
Displacement
416 SS
Nodular Iron
Rotor Gears
Displacement
TiN coated
Nodular Iron
Nodular Iron
TiN coated
Nodular Iron
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Anodized
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Covers
Anodized
356 Alum
Anodized
356 Alum
Covers
Buna-N
Buna-N
Buna-N
Seals**
Buna-N
Buna-N
Seals**
Standard
Standard
Standard
Adjuster
Mechanical
Standard
Standard
(if required)
Adjuster
Mechanical
3" 125#
3" 125#
ANSI
flat faced
3" 125#
ANSI
flat faced
4" x 45 deg.
4" NPT
Buna-N
356 Alum Andz
4" x 45 deg.
4" NPT
Buna-N
356 Alum Andz
4" x 45 deg.
4" NPT
Buna-N
Cast Iron
& Elbows
Flanges
Standard
4" NPT
Buna-N
356 Alum Andz
4" NPT
Buna-N
Cast Iron
(if required)
Flanges
Standard
ANSI
Standard
Hi Temp
Option
Standard
Standard
Steel
Viton
Viton
Viton
flat faced
Cast Iron
Cast Iron
Cast Iron
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Buna-N
356 Alum
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
Strainer
Standard
Buna-N
Anodized
356 Alum
Buna-N
356 Alum
(if required
Strainer
Standard
available
Not
Viton
Steel
Viton
Steel
19
Anodized
Anodized
Aviation
356 Alum
Buna-N
Seals** Adjuster
Mechanical
Standard
L1608
Anodized
ammonia (NH3).
Anhydrous
356 Alum
12
/Carbon
Ni-Resist II
/Carbon
Anodized
L1612
gas.
petroleum
Liquified
Hardcoat
Anodized
Hardcoat
518 Alum
Anodized
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
17.4 pH SS
Iron
Sintered
Rotor Gear
Blocking
Iron
17.4 pH SS
Iron
Sintered
Rotor Gears
Displacement
Iron
or none
316 SS
or none
316 SS
Iron/
Sintered
Gears
Drive
or none
316 SS
Iron/
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
360 Alum
Buna-N
Seals**
Adjuster
Mechanical
360 Alum
Covers
Anodized
Buna-N
Seals**
UL Approved
Adjuster
Mechanical
Anodized
360 Alum
Anodized
UL Approved
Buna-N
UL Approved
Standard
Standard
Ni-Resist II
356 Alum
518 Alum
Rotor
Blocking
Hardchrome
Sintered
Covers
10
Plates
Bearing
Anodized
Sintered
Internal Hardware
(if required)
Housing
Anodized
Hardcoat
Sintered
Drive Gears
Application
Element*
Class
MA-5 Meters
gas.
petroluem
Liquified
/Carbon
316 SS
Rotor Gears
Displacement
6" Victaulic
Anodized
518 Alum
Blocking Rotor Gear
Anodized
L1607
518 Alum
Rotor Journals
Steel
Stainless
Standard
Ni-Resist II
Rotors
Displacement
coated
Armoloy
(if required)
& Elbows
Flanges
Standard
4" x 45 deg.
4" NPT
Buna-N
356 Alum Andz
4" x 45 deg.
4" NPT
Buna-N
Cast Iron
356 Alum
Rotor
Blocking
Hardchrome
300 Series
Covers
Buna-N
Hi Temp
Option
Standard
10
Plates
Bearing
Anodized
416 SS
Internal Hardware
Anodized
356 Alum
Viton
(if required)
Housing
Anodized
Hardcoat
Ni-Resist II
Rotor Gears
Displacement
Steel
Stainless
300 Series
Anodized
356 Alum
Application
Element*
Class
MA-4 Meters
gasolines.
/Carbon
316 SS
Blocking Rotor Gear
416 SS
Steel
Stainless
300 Series
Anodized
356 Alum
Rotor Journals
coated
Armoloy
Ni-Resist II
Nodular Iron
L3550
356 Alum
316 SS Hardchrome
Nodular Iron
Standard
Ni-Resist II
Rotors
Displacement
316 SS Hardchrome
356 Alum
Rotor
Blocking
Anodized
Red
356 Alum
Anodized
Red
356 Alum
2
Plates
Bearing
Anodized
Red
356 Alum
Anodized
Red
356 Alum
(if required)
Housing
Alum/Carbon
Hardcoat
Ni-Resist II
Application
Element*
Class
M-80 Meters
adhesives.
Latex &
water based
For oil &
356 Alum
15
L3561
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L3541
M-60 Meters‌.Continued
360 Alum And
1-1/2" NPT
UL Buna-N
Nodular Iron
360 Alum And
1-1/2" NPT
UL Buna-N
Nodular Iron
(if required)
& Elbows
Flanges
Standard
360 Alum And
1-1/2" NPT
UL Buna-N
Nodular Iron
(if required)
& Elbows
Flanges
Standard
available
Not
(if required)
Strainer
Standard
Buna-N
Anodized
356 Alum
Viton
356 Alum
20
Anodized
Anodized
Anodized
Anodized
Anodized
pH liquids.
& alkaline
solvents
Chlorinated
L4107
7
gasolines.
Cast Iron
Anodized
Aviation
356 Alum
2
L4116
products.
petroleum
Refined
356 Alum
1
Housing
L4115
Application
Element*
Class
MS-7 Meters
gas.
petroleum
Liquified
356 Alum
10
Housing
L3210
Application
Element*
Class
MA-15 Meters
fluids (ADF).
de-icing
Aircraft
356 Alum
14
L2143
(NH3).
Ammonia
Anhydrous
356 Alum
12
L2612
gas.
petroleum
Liquified
356 Alum
10
Housing
L2321
Application
Element*
Class
MA-7 Meters
/Carbon
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
/Carbon
Ni-Resist II
Plates
Bearing
Ni-Resist II
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Plates
Bearing
Cast Iron
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Cast Iron
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Anodized
518 Alum
Rotors
Displacement
Anodized
Red
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Iron
Sintered
Ni-Resist II
Iron
Sintered
Rotor Gear
Blocking
Coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
Iron
Sintered
Ni-Resist II
Iron
Sintered
Rotor Gear
Iron
Sintered
Ni-Resist II
Iron
Sintered
Rotor Gears
Displacement
Nodular Iron
Rotor Gears
Displacement
Iron
Sintered
Ni-Resist II
Iron
Sintered
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Steel
Inside
Coated
Epoxy
Steel
Steel
Covers
Anodized
360 Alum
Covers
Anodized
360 Alum
Anodized
360 Alum
Anodized
360 Alum
Covers
Viton
Buna-N
Buna-N
Seals**
UL Approved
Buna-N
Seals**
UL Approved
Buna-N
UL Approved
Buna-N
UL Approved
Buna-N
Seals**
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
(if required)
Flanges
Standard
3" NPT
UL Buna-N
Ductile Iron
(if required)
(if required) Standard
Flanges
Standard
2" NPT
Buna
356 Alum Andz
2" NPT
UL Buna-N
Nodular Iron
2" NPT
UL Buna-N
Nodular Iron
(if required)
Flanges
Standard
Adjuster
Mechanical
Hi Temp
Standard
Standard
(if required)
Adjuster
Mechanical
Viton
Steel
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
UL Approved
Buna-N
Anodized
356 Alum
(if required)
Strainer
Standard
Buna-N
356 Alum
UL Approved
Buna-N
Anodized
356 Alum
UL Approved
Buna-N
Anodized
356 Alum
(if required)
Strainer
Standard
21
Anodized
solvent service
L4115
316 SS
316 SS
316 SS
Hardchrome
Sintered
Ni-Resist II
Iron
Sintered
Ni-Resist II
Iron
Sintered
Rotor Gears
Displacement
Iron
Sintered
Anodized
crude oil.
High Sulphur
L4109
37
(not chlorinated).
service
solvent
Cast Iron
Anodized
For general
356 Alum
16
L4126
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4129
pH liquids.
& alkaline
solvents
Chlorinated
L4107
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
/Carbon
"Red"
Cast Iron
Anodized
Hardcoat
518 Alum
Anodized
Red
518 Alum
"Red"
Cast Iron
Anodized
518 Alum
Anodized
Red
518 Alum
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
Iron
Sintered
Iron
Sintered
Iron
Sintered
Iron
Iron
Sintered
Iron
Sintered
Iron
Sintered
Iron
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Covers
Steel
Steel
Steel
Steel Coated
Epoxy
Steel
Steel
Steel
Steel
Cast Iron
Anodized
518 Alum
Hardchrome
Sintered
Rotor Gear
Blocking
Iron
Sintered
Iron
Sintered
Steel
Stainless
300 Series
Inside Cast Iron
Anodized
Hardcoat
518 Alum
Anodized
316 SS
Journals
Rotor
Hardchrome
Iron
Sintered
Iron
Sintered
7
Ni-Resist II
Ni-Resist II
Hardcoat Anodized
518 Alum
316 SS Hardchrome
Iron
Sintered
gasolines.
Cast Iron
Anodized
Aviation
356 Alum
2
Anodized
L4116
products.
petroleum
Refined
518 Alum
Rotors
Displacement
316 SS Hardchrome
Buna-N
Seals**
Viton
Buna-N
Viton
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Hi Temp
Option
Standard
Viton
Buna-N
Viton
Viton
Buna-N
Hi Temp
Option
Standard
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
Ni-Resist II
Rotor
Blocking
"Red"
Cast Iron
Anodized
518 Alum
Anodized
Red
518 Alum
1
Plates
Bearing
"Red"
Cast Iron
Anodized
Hardcoat
518 Alum
Anodized
Red
518 Alum
(if required)
356 Alum
Housing
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
Application
Element*
Class
MSAA-7 Meters
crude oil.
High Sulphur
L4109
37
(not chlorinated).
Cast Iron
Anodized
For general
356 Alum
16
L4126
products or both
or viscous
oils, heated
For crude
356 Alum
14
L4129
MS-7 Meters‌.Continued 2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
Steel
Viton
Steel
Buna-N
Steel
Viton
Steel
Viton
Steel
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
Viton
Steel
Buna-N
Steel
Viton
Cad
S
40
Cad
S
40
Cad
S
40
Cad
S
40
Ava
Cad
S
40
Ba
Str
Sta
Cad
S
40
Cad
S
40
Cad
S
40
22
316 SS
Anodized
crude oil.
High Sulphur
L4109
37
or both.
products
or viscous
oils, heated
Cast Iron
Anodized
For crude
356 Alum
14
L4129
gas.
petroleum
Liquified
356 Alum
10
L4125
Ni-Resist II
Ni-Resist II
/Carbon
Ni-Resist II
Option
/Teflon
/Carbon
For acidic
316 SS
/Carbon
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
/Carbon
Ni-Resist II
pH liquids.
L4188
8
pH liquids.
& alkaline
solvents
Chlorinated
L4107
7
products.
petroleum
Cast Iron
Anodized
Refined
356 Alum
1
Housing
L4115
Application
Element*
Class
MSA-7 Meters
crude oil.
High Sulphur
L4109
37
not chlorinated).
service
solvent
Cast Iron
Anodized
For general
356 Alum
16
L4126
"Red"
Cast Iron
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
"Red"
316 SS
Cast Iron
Anodized
Hardcoat
518 Alum
Rotor
Blocking
"Red"
Cast Iron
Anodized
Hardcoat
518 Alum
MSAA-7 Meters ‌Continued
"Red"
Cast Iron
Anodized
Red
518 Alum
Anodized
518 Alum
"Red"
316 SS
Cast Iron
Anodized
518 Alum
Rotors
Displacement
"Red"
Cast Iron
Anodized
518 Alum
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
Iron
Sintered
Iron
Sintered
Iron
Sintered
316 SS
Iron
Sintered
Iron
Sintered
Rotor Gear
Blocking
Iron
Sintered
Iron
Sintered
Iron
Sintered
Iron
Sintered
Iron
Sintered
Coated
Armoloy
316 SS
Iron
Sintered
Iron
Sintered
Rotor Gears
Displacement
Iron
Sintered
Iron
Sintered
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Steel
Steel
316 SS
Steel
Steel
Covers
Steel
Steel
Viton
Viton
UL Approved
Buna-N
Teflon
Viton
Buna-N
Seals**
Viton
Buna-N
2"
Flanges
Standard
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
Standard
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
SS
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
(if required) (if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Steel
Viton
Steel
Viton
Steel
Buna-N
Steel
Available
Not
Viton
Steel
Buna-N
Steel
(if required)
Strainer
Standard
Viton
Steel
Buna-N
Cad P
Ste
40 M
Cad P
Ste
40 M
304
100 M
Availa
No
Cad P
Ste
40 M
Cad P
Ste
40 M
(if requ
Bas
Strai
Stand
Cad P
Ste
40 M
Cad P
Ste
40 M
23
Anodized
crude oil.
High Suplhur
L4109
37
products or both.
or viscous
oils, heated
Cast Iron
Anodized
For crude
356 Alum
14
L4129
Ni-Resist II
Ni-Resist II
Option
/Teflon
For acidic
/Carbon
316 SS
Ni-Resist II
Plates
Bearing
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
pH liquids.
L4188
8
products.
petroleum
316 SS
Anodized
Refined
356 Alum
1
Housing
L4115
Application
Element*
Class
MSC-7 Meters
crude oil.
High Sulphur
L4109
37
or both.
products
or viscous
oils, heated
Cast Iron
Anodized
For crude
356 Alum
14
L4129
products.
petroleum
Refined
356 Alum
1
Housing
L4115
Application
Element*
Class
MSB-7 Meters
"Red"
"Red"
Cast Iron
Anodized
Anodized
Cast Iron
Red
518 Alum
"Red"
316 SS
Anodized
518 Alum
Rotors
Displacement
"Red"
Red
518 Alum
"Red"
316 SS
Anodized
Hardcoat
518 Alum
Rotor
Blocking
"Red"
Cast Iron
Anodized
Anodized
Cast Iron
Red
518 Alum
Anodized
518 Alum
Rotors
Displacement
Red
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Iron
Sintered
Iron
Sintered
316 SS
Iron
Sintered
Rotor Gear
Blocking
Iron
Sintered
Iron
Sintered
Iron
Sintered
Rotor Gear
Iron
Sintered
Iron
Sintered
Coated
Armoloy
316 SS
Iron
Sintered
Rotor Gears
Displacement
Iron
Sintered
Iron
Sintered
Iron
Sintered
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Steel
Steel
316 SS
Steel
Covers
Steel
Steel
Steel
Covers
Viton
Viton
Teflon
Buna-N
Seals**
Viton
Viton
Buna-N
Seals** Flanges
Standard
2"
Flanges
Standard
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
Standard
ANSI
Steel
Raised Face
2"
ANSI
Steel
Raised Face
2"
ANSI
SS
Raised Face
2"
ANSI
Steel
Raised Face
2"
(if required) (if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
(if required) (if required)
Adjuster
Mechanical
Available
Not
Available
Not
Available
Not
Available
Not
(if required)
Strainer
Standard
Available
Not
Available
Not
Available
Not
(if required)
Strainer
Standard
Avail
No
Avail
No
Avail
No
Avail
No
(if requ
Bas
Strai
Stand
Avail
No
Avail
No
Avail
No
(if requ
Bas
Strai
Stand
24
Anodized
Anodized
Anodized
Anodized
Anodized
pH liquids.
For acidic
L4208
8
gasolines.
316 SS
Anodized
Aviation
356 Alum
2
L4202
products.
petroleum
Refined
356 Alum
1
Housing
L4200
Application
Element*
Class
MSAA-15 Meters
(not chlorinated).
solvent service
For general
356 Alum
16
L4225
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4214
gasolines.
Aviation
356 Alum
2
L4202
products.
petroleum
Refined
356 Alum
1
Housing
L4200
Application
Element*
Class
MS-15 Meters
/Carbon
316 SS
Ni-Resist II
Ni-Resist II
Plates
Bearing
/Carbon
Ni-Resist II
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
"Red"
316 SS
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Hardcoat
518 Alum
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
"Red"
316 SS
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Anodized
518 Alum
Anodized
Red
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
316 SS
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Internal
Stainless Steel
Coated
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Armoloy
316 SS
coated
Armoloy
416 SS
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
coated
Armoloy
416 SS
Nodular Iron
Rotor Gears
Displacement
316 SS
inside
coated
Epoxy
Steel
Steel
Covers
Steel
Steel
inside
coated
Epoxy
Steel
Steel
Covers
PTFE
Buna-N
Buna-N
Seals**
Buna-N
Viton
Buna-N
Buna-N
Seals**
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Standard
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
SS
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
Available
Not
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
Buna-N
Steel
Viton
Steel
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
25
Anodized
Anodized
Anodized
Anodized
Anodized
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4214
gas.
petroleum
Liquified
356 Alum
10
L4225
products.
petroleum
Refined
356 Alum
1
Housing
L4200
Application
Element*
Class
MSA-15 Meters
(not chlorinated).
service
solvent
For general
356 Alum
16
L4225
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4214
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
Plates
Bearing
/Carbon
Ni-Resist II
Ni-Resist II
Red Anodized
Anodized
518 Alum
Anodized
518 Alum
Anodized
518 Alum
Rotors
Displacement
Anodized
Red
518 Alum
Anodized
Hardcoat
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Anodized
Hardcoat
518 Alum
Anodized
Anodized
518 Alum
Red
518 Alum
Red
518 Alum
MSAA-15 Meters . . . Continued 316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Nodular Iron
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Steel
Steel
Covers
Steel
Steel
Viton
UL Approved
Buna-N
Buna-N
Seals**
Buna-N
Viton
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Standard
Hi Temp
Option
Standard
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
Steel
Viton
Steel
Buna-N
Steel
Buna-N
Steel
(if required)
Strainer
Standard
Buna-N
Steel
Viton
26
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
gasolines.
Aviation
356 Alum
2
L4302
products.
petroleum
Refined
356 Alum
1
Housing
L4300
Application
Element*
Class
MS-30 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4214
products.
petroleum
Refined
356 Alum
1
Housing
L4200
Application
Element*
Class
MSC-15 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4214
products.
petroleum
Refined
356 Alum
1
Housing
L4200
Application
Element*
Class
MSB-15 Meters
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
Ni-Resist II
Plates
Bearing
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
Anodized
Blocking
Red
518 Alum
Anodized
518 Alum
Rotors
Red
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Displacement
Anodized
Anodized
Blocking
Red
518 Alum
Anodized
518 Alum
Rotors
Displacement
Red
518 Alum
Anodized
Hardcoat
518 Alum
Rotor
Blocking
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
coated
Armoloy
416 SS
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Inside
Coated
Epoxy
Steel
Steel
Covers
Steel
Steel
Covers
Steel
Steel
Covers
Buna-N
Buna-N
Seals**
Viton
Buna-N
Seals**
Viton
Buna-N
Seals**
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
Available
Not
Available
Not
(if required)
Strainer
Standard
Available
Not
Available
Not
(if required)
Strainer
Standard
27
Anodized
Anodized
pH liquids.
For acidic
L4308
8
pH liquids.
& alkaline
solvents
Chlorinated
L4307
7
gasolines.
316 SS
Cast Iron
Anodized
Aviation
356 Alum
2
L4302
products.
petroleum
Refined
356 Alum
1
Housing
L4300
Application
Element*
Class
MSAA-30 Meters
crude oil.
High Sulphur
L4311
37
(not chlorinated).
service
solvent
Cast Iron
Anodized
For general
356 Alum
16
L4325
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
Cast Iron
L4314
pH liquids.
& alkaline
solvents
Chlorinated
L4307
7
/Carbon
316 SS
/Carbon
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
/Carbon
Ni-Resist II
MS-30 Meters‌Continued
"Red"
316 SS
Cast Iron
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
"Red"
Cast Iron
Anodized
Hardcoat
356 Alum
Anodized
Red
356 Alum
Cast Iron
"Red"
316 SS
Cast Iron
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
"Red"
Cast Iron
Anodized
356 Alum
Anodized
Red
356 Alum
Cast Iron
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
coated
Armoloy
Nodular Iron
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
316 SS
Nodular Iron
coated
Armoloy
416 SS
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Nodular Iron
Nodular Iron
3"
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
ANSI
SS
Standard
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Hi Temp
Option
Standard
Standard
Steel
PTFE
Viton
Buna-N
Buna-N
Seals**
Viton
Buna-N
Viton
Viton
Raised Face
316 SS
Steel
Inside
Coated
Epoxy
Steel
Steel
Covers
Steel
Steel
Steel
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Available
Not
Viton
Steel
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
Viton
Steel
Buna-N
Steel
Viton
Steel
Viton
Steel
28
Anodized
Anodized
crude oil.
High Sulphur
L4311
37
products or both.
heated or viscous
Cast Iron
Anodized
For crude oils,
356 Alum
14
L4314
petroleum gas.
Liquified
356 Alum
10
L4325
pH liquids.
solvents & alkaline
Chlorinated
L4307
7
petroleum products.
Cast Iron
Anodized
Refined
356 Alum
1
Housing
L4300
Application
Element*
Class
MSA-30 Meters
crude oil.
High Sulphur
L4311
37
(not chlorinated).
service
solvent
Cast Iron
Anodized
For general
356 Alum
16
L4325
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4314
Ni-Resist II
Ni-Resist II
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
/Carbon
Ni-Resist II
Ni-Resist II
"Red"
"Red"
Cast Iron
Anodized
Anodized
Cast Iron
Red
356 Alum
Anodized
356 Alum
Cast Iron
Anodized
356 Alum
Rotors
Displacement
"Red"
Cast Iron
Anodized
Red
356 Alum
Anodized
Hardcoat
356 Alum
Cast Iron
Anodized
Hardcoat
356 Alum
Rotor
Blocking
"Red"
Cast Iron
Anodized
Hardcoat
356 Alum
Anodized
Anodized
356 Alum
Red
356 Alum
Red
356 Alum
MSAA-30 Meters‌ Continued 316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Nodular Iron
Nodular Iron
Nodular Iron
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
coated
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Stainless
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Nodular Iron
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Steel
Steel
Steel
Steel
Steel
Covers
Steel
Steel
Steel
Viton
Viton
UL Approved
Buna-N
Viton
Buna-N
Seals**
Viton
Buna-N
Viton
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Hi Temp
Option
Standard
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
Steel
Viton
Steel
Viton
Steel
Buna-N
Steel
Viton
Steel
Buna-N
Steel
(if required
Strainer
Standard
Viton
Steel
Buna-N
Steel
Viton
29
Anodized
Anodized
crude oil.
High Sulphur
L4311
37
or both.
products
or viscous
oils, heated
Cast Iron
Anodized
For crude
356 Alum
14
L4314
products.
petroleum
Refined
356 Alum
1
Housing
L4300
Application
Element*
Class
MSC-30 Meters
crude oil.
High Sulphur
L4311
37
products or both.
heated or viscous
Cast Iron
Anodized
For crude oils,
356 Alum
14
L4314
products.
petroleum
Refined
356 Alum
1
Housing
L4300
Application
Element*
Class
MSB-30 Meters
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
Ni-Resist II
Ni-Resist II
Ni-Resist II
Plates
Bearing
"Red"
"Red"
Cast Iron
Anodized
Anodized
Cast Iron
Red
356 Alum
Anodized
356 Alum
Rotors
Displacement
"Red"
Red
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
"Red"
Cast Iron
Anodized
Anodized
Cast Iron
Red
356 Alum
Anodized
356 Alum
Rotors
Displacement
Red
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
coated
Armoloy
Nodular Iron
Rotor Gear
Nodular Iron
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Steel
Steel
Steel
Covers
Steel
Steel
Steel
Covers
Viton
Viton
Buna-N
Seals**
Viton
Viton
Buna-N
Seals**
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
Available
Not
Available
Not
Available
Not
(if required)
Strainer
Standard
Available
Not
Available
Not
Available
Not
(if required)
Strainer
Standard
30
Anodized
Anodized
Anodized
Anodized
Anodized
petroleum products
Refined
356 Alum
1
Housing
L4500
Application
Element*
Class
MSAA-75 Meters
(not chlorinated).
solvent service
For general
356 Alum
16
L4525
products or both.
heated or viscous
For crude oils,
356 Alum
14
Anodized
L4514
gasolines.
Aviation
L4502
2
petroleum products.
356 Alum
Anodized
Refined
356 Alum
1
Housing
L4500
Application
Element*
Class
MS-75 Meters
gasolines.
Aviation
356 Alum
2
L4382
products.
petroleum
Refined
356 Alum
1
Housing
L4375
Application
Element*
Class
MS-40 Meters
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Ni-Resist II
/Carbon
Cast Iron
Ni-Resist II
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Ni-Resist II
/Carbon
Ni-Resist II
Plates
Bearing
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Hardcoat
Anodized
356 Alum
Rotors
Displacement
Anodized
356 Alum
Anodized
Anodized
356 Alum
Red
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Red
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Rotor
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Nodular Iron
Rotor Gear
Blocking
Nodular Iron
Nodular Iron
coated
Armoloy
Ni-Resist II
Nodular Iron
Rotor Gear
Blocking
coated
Armoloy
Ni-Resist II
coated
Armoloy
Nodular Iron
Rotor Gear
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
416 SS
Nodular Iron
Rotor Gears
Displacement
416 SS
coated
Armoloy
Nodular Iron
Rotor Gears
Displacement
Internal
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Steel
Covers
Steel
Steel
Inside
Coated
Epoxy
Steel
Steel
Covers
Inside
Coated
Epoxy
Steel
Steel
Covers
Buna-N
Seals**
Buna-N
Viton
Buna-N
Buna-N
Seals**
Buna-N
Buna-N
Seals**
Standard
(if required)
Adjuster
Mechanical
Standard
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
4"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
3"
ANSI
Steel
Raised Face
3"
(if required)
Flanges
Standard
Buna-N
Steel
(if required)
Strainer
Standard
Buna-N
Steel
Viton
Steel
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
Available
Not
Buna-N
Steel
(if required)
Strainer
Standard
31
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
products.
petroleum
Refined
356 Alum
1
Housing
L4500
Application
Element*
Class
MSB-75 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4514
MSA-75 Meters
gas.
petroleum
Liquified
356 Alum
10
L4525
products.
petroleum
Refined
356 Alum
1
Housing
L4500
Application
Element*
Class
MSA-75 Meters
(not chlorinated).
solvent service
For general
356 Alum
16
L4525
products or both.
heated or viscous
For crude oils,
356 Alum
14
L4514
gasolines.
Aviation
356 Alum
2
L4502
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Cast Iron
/Carbon
Ni-Resist II
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Ni-Resist II
/Carbon
Cast Iron
Ni-Resist II
Anodized
Hardcoat
356 Alum
Rotor
Anodized
356 Alum
Rotors
Displacement
Anodized
Anodized
Blocking
Red
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
Red
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Hardcoat
356 Alum
Anodized
Anodized
356 Alum
Red
356 Alum
Anodized
356 Alum
Red
356 Alum
Anodized
Hardcoat
356 Alum
MSAA-75 Meters‌Continued 316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
Nodular Iron
Rotor Gear
Blocking
Nodular Iron
Nodular Iron
Nodular Iron
Rotor Gear
Blocking
Nodular Iron
Nodular Iron
coated
Armoloy
Ni-Resist II
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
416 SS
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Steel
Covers
Steel
Steel
Steel
Covers
Steel
Steel
Inside
Coated
Epoxy
Buna-N
Seals**
Viton
UL Approved
Buna-N
Buna-N
Seals**
Buna-N
Viton
Buna-N
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Standard
Hi Temp
Option
Standard
Standard
4"
ANSI
Steel
Raised Face
4"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
Not
Available
Not
(if required)
Strainer
Standard
Viton
Steel
Buna-N
Steel
Buna-N
Steel
(if required)
Strainer
Standard
Buna-N
Steel
Viton
Steel
Available
32
Anodized
Anodized
Anodized
Anodized
Anodized
Anodized
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4814
gasolines.
Aviation
356 Alum
2
L4802
products.
petroleum
Refined
356 Alum
1
Housing
L4800
Application
Element*
Class
MS-120 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4514
products.
petroleum
Refined
356 Alum
1
Housing
L4500
Application
Element*
Class
MSC-75 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4514
/Carbon
Cast Iron
/Carbon
Ni-Resist II
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Cast Iron
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Cast Iron
Anodized
Red
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Anodized
Red
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
Anodized
Blocking
Red
356 Alum
Anodized
356 Alum
Rotors
Red
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Displacement
Anodized
Anodized
Blocking
Red
356 Alum
Red
356 Alum
MSB-75 Meters‌.Continued 316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
Ni-Resist II
Ni-Resist II
Ni-Resist II
Rotor Gear
Blocking
Nodular Iron
Nodular Iron
Rotor Gear
Blocking
Nodular Iron
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Rotor Gears
Displacement
Nodular Iron
Nodular Iron
Rotor Gears
Displacement
Nodular Iron
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Inside
Coated
Epoxy
Steel
Steel
Covers
Steel
Steel
Covers
Steel
Viton
Buna-N
Buna-N
Seals**
Viton
Buna-N
Seals**
Viton
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
4"
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
4"
ANSI
Steel
Raised Face
4"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
Not
Viton
Steel
Available
Not
Buna-N
Steel
(if require
Strainer
Standard
Available
Not
Available
Not
(if require
Strainer
Standard
Available
33
Anodized
Anodized
Anodized
Anodized
Anodized
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4814
petroleum gas.
Liquified
356 Alum
10
L4800
products.
petroleum
Refined
356 Alum
1
Housing
L4800
Application
Element*
Class
MSA-120 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4814
pH liquids.
For acidic
L4818
8
gasolines.
316 SS
Anodized
Aviation
356 Alum
2
L4802
products.
petroleum
Refined
356 Alum
1
Housing
L4800
Application
Element*
Class
MSAA-120 Meters
/Carbon
Cast Iron
/Carbon
Cast Iron
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Cast Iron
/Carbon
316 SS
/Carbon
Ni-Resist II
/Carbon
Cast Iron
Plates
Bearing
Anodized
Red
356 Alum
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Red
356 Alum
"Red"
316 SS
Anodized
Hardcoat
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Anodized
Red
356 Alum
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Anodized
Red
356 Alum
"Red"
316 SS
Anodized
356 Alum
Anodized
356 Alum
Rotors
Displacement
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Ni-Resist II
Ni-Resist II
Ni-Resist II
Rotor Gear
Blocking
Ni-Resist II
316 SS
Ni-Resist II
Ni-Resist II
Rotor Gear
Internal
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Rotor Gears
Displacement
Coated
Armoloy
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
coated 410 SS
Stainless
300 Series
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Armoloy
316 SS
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Rotor Gears
Displacement
Steel
Steel
Steel
Covers
Steel
316 SS
Inside
Coated
Epoxy
Steel
Steel
Covers
Viton
UL Approved
Buna-N
Buna-N
Seals**
Viton
PTFE
Buna-N
Buna-N
Seals**
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
6"
ANSI
SS
Raised Face
6"
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
(if required)
Flanges
Standard
Viton
Steel
Buna-N
Steel
Buna-N
Steel
(if required)
Strainer
Standard
Viton
Steel
Available
Not
Available
Not
Buna-N
Steel
(if required
Strainer
Standard
34
Anodized
Anodized
Anodized
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4824
pH liquids.
For acidic
L4888
8
products.
petroleum
316 SS
Anodized
Refined
356 Alum
1
Housing
L4860
Application
Element*
Class
MSC-120 Meters
or both.
products
or viscous
oils, heated
For crude
356 Alum
14
L4824
products.
petroleum
Refined
356 Alum
1
Housing
L4860
Application
Element*
Class
MSB-120 Meters
/Carbon
Cast Iron
/Carbon
316 SS
/Carbon
Cast Iron
Plates
Bearing
/Carbon
Cast Iron
/Carbon
Cast Iron
Plates
Bearing
Red Anodized
Anodized
356 Alum
"Red"
316 SS
Anodized
356 Alum
Rotors
Red
356 Alum
"Red"
316 SS
Anodized
Hardcoat
356 Alum
Rotor
Displacement
Anodized
Anodized
Blocking
Red
356 Alum
Anodized
356 Alum
Rotors
Displacement
Red
356 Alum
Anodized
Hardcoat
356 Alum
Rotor
Blocking
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Rotor
Hardchrome
316 SS
Hardchrome
316 SS
Journals
Blocking
Ni-Resist II
316 SS
Ni-Resist II
Rotor Gear
Blocking
Ni-Resist II
Ni-Resist II
Rotor Gear
Internal
Coated
Armoloy
Steel
Stainless
300 Series
Steel
coated 410 SS
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Internal
Steel
Stainless
300 Series
Steel
Stainless
300 Series
Hardware
Armoloy
316 SS
Coated
Armoloy
410 SS
Rotor Gears
Displacement
Coated
Armoloy
410 SS
Coated
Armoloy
410 SS
Rotor Gears
Displacement
Steel
316 SS
Steel
Covers
Steel
Steel
Covers
Viton
PTFE
Buna-N
Seals**
Viton
Buna-N
Seals**
Hi Temp
Option
Standard
Standard
Standard
(if required)
Adjuster
Mechanical
Hi Temp
Option
Standard
Standard
(if required)
Adjuster
Mechanical
ANSI
Steel
Raised Face
6"
ANSI
SS
Raised Face
6"
ANSI
Steel
Raised Face
6"
(if required)
Flanges
Standard
ANSI
Steel
Raised Face
6"
ANSI
Steel
Raised Face
6"
(if required)
Flanges
Standard
Available
Not
Available
Not
Available
Not
(if required)
Strainer
Standard
Available
Not
Available
Not
(if required)
Strainer
Standard
Chemical Composition of Metals A356.0 Aluminum Silicon 6.5 - 7.5% Manganese .1% Max. Iron .2% Max. Copper .2% Max. Magnesium .25 - .45% Zinc .1% Max. Titanium .2% Max. Others Each .05% Max. Others Total .15% Max Aluminum - remainder Ni-Resist Type II Carbon 3.0% Silicon 1.0 to 2.8% Manganese 0.80 to 1.3% Nickel 18.0 to 22.0% Copper 0.50% Chromium 1.75 to 3.5% Sulfur 0.12% Iron - remainder Carbon steel Carbon .30% Manganese 1.0% Phosphorus .05% Sulfur .06% Silicon .60% Iron - remainer
17-4 pH Stainless steel Carbon .07 Max % Manganese 1.0% Max. Silicon 1.0% Max. Phosphorus .04% Max. Sulfur .03% Max. Chromium 15.5 - 17.5% Nickel 3.0 - 5.0% Copper 3.0 - 5.0% Niobium .15 - .45% Niobium + Tantalum .15 .45% Iron - remainder
Nodular iron Carbon 3.5% Silicon 2.56% Manganese .54% Phosphorus .12% Sulfur .010% Nickel 1.50% Magnesium .055% Iron - remainder 416 Stainless steel Carbon .15 Max % Manganese 1.25 Max % Silicon 1.0 Max % Chromium 12.0 - 14.0% Phosphorus .04 Max % Sulfur .18 - .35% Molybdenum .60 Max % Iron - remainder
Red brass Copper 85% Tin 5% Lead 5% Zinc 5% Cast iron class 35 Carbon 3.10 to 3.30% Silicon 2.0 - 2.2% Phosphorus .15 - .30% Sulfur .08 - .12% Manganese .45 - 70% Iron - remainder
304 Stainless steel Carbon .08% Manganese 2.0% Silicon 1.0% Chromium 18.0 - 20.0% Nickel 8.0 - 11.0% Iron - remainder
316 Stainless steel Carbon .10 Max % Manganese 2.0 Max % Silicon 1.0 Max % Chromium 16.0 - 18.0% Nickel 10.0 - 14.0% Molybdenum 2.0 - 3.0% Iron - remainder 18-8 Type 302 Stainless steel Carbon .08 - .15% Manganese 2.0 Max % Silicon 1.0 Max % Chromium 17.0 - 19.0% Nickel 8.0 - 10.0% Iron - remainder 360.0 Aluminum Silicon 9.0 to 10.0% Iron 2% Max. Copper .6% Max. Manganese .35% Max. Magnesium .4 to .6% Nickel .5% Max. Zinc .5% Max. Tin .15% Max. Others Total .25% Max. Aluminum - remainder
Metal treatments to increase corrosion resistance Anodized aluminum An electrochemical process which forms a thin uniform oxide on metal surfaces that increases corrosion resistance. Hardcoat or hard anodized aluminum This process is similar to above but produces a harder, thicker oxide film that affords greater abrasion resistance than standard anodizing. Electropolished stainless steel Removal of a thin layer of metal by anodic treatment produces a bright passive finish. Passivated stainless steel By chemically removing particles of iron imbedded in metal during machining and producing a thin transparent oxide film by use of an oxidizing agent, this increases corrosion resistance.
35
Cadmium plated and dichromated carbon steel Electroplated cadmium is treated in an oxidizing agent which is used mainly for rust protection. Hard chrome plated stainless steel Electroplated chromium (special process) is used when high wear and corrosion resistance is required. Epoxy coated carbon steel and aluminum Epoxy resins are the combination of polyphenois and epichlorhyrin and have a good resistance to acids, alkalis and many solvents.
Conversions Pressure of water at different heads Pre ssure a nd e quiva le nt he a d of w a te r (fe e t)
He a d of w a te r (fe e t) a nd e quiva le nt pre ssure Head Feet 1 2 3 4 5 6 7 8 9 10 20 30 40 50
Lbs. Per Head Lbs. Per Head Lbs. Per Sq. In. Feet Sq. In. Feet Sq. In. 0.43 60 25.99 200 86.62 0.87 70 30.32 225 97.45 1.30 80 34.65 250 108.27 1.73 90 38.98 275 119.10 2.17 100 43.31 300 129.93 2.60 110 47.64 325 140.75 3.03 120 51.97 350 151.58 3.40 130 56.30 400 173.24 3.90 140 60.63 500 216.55 4.33 150 64.96 600 259.85 8.66 160 69.29 700 303.16 12.99 170 73.63 800 346.47 17.32 180 77.96 900 389.78 21.65 190 82.29 1,000 433.09
Lbs. Per Head Sq. In. Feet 1 2.31 2 4.62 3 6.93 4 9.24 5 11.54 6 13.85 7 16.61 8 18.47 9 20.78 10 23.09 15 34.63 20 46.18 25 57.72 30 69.27
Lbs. Per Sq. In. 40 50 60 70 80 90 100 110 120 125 130 140 150 160
Head Lbs. Per Head Feet Sq. In. Feet 92.36 170 392.52 115.45 180 415.61 138.54 190 438.9 161.63 200 461.78 184.72 225 519.51 207.81 250 577.24 230.9 275 643.03 253.98 300 692.69 277.07 325 750.41 288.62 350 808.13 300.16 375 865.89 323.25 400 922.58 346.43 500 1154.48 369.43 1,000 2308.00
For materials other than water Pressure in pounds per square inch = Head in feet x Specific Gravity 2.31
Conversion Factors Length
Multiply to get Inch ft ft yard Angstrom
→ ←
2.54 12 0.305 1.094 10
Pressure / Vacuum
to get Divide cm inch meter meter meter
Flowrate Multiply to get cc/min cfm (ft3/min) cfm (ft3/min) cfh (ft3/hr) cfh (ft3/hr) GPH GPH GPM GPM oz/min
→ ←
1 28.31 1.699 472 0.125 63.1 0.134 0.227 3.785 29.57
to get Divide ml/min L/min m3/hr ml/min GPM ml/min cfh m3/hr L/min ml/min
Multiply
→ ←
Volume to get
Multiply to get Cubic cm (cc) oz (fluid) cubic ft (ft3) cubic ft (ft3) gal gal gal cubic meters
to get atm atm atm atm atm atm bar bar bar ft H2O
33.9 760 1033.2 14.7 1.013 101.3 14.5 0.9869 100 0.4335
Divide ft H2O mm Hg g/cm2 psi bar kPa psi atm kPa psi
ft H2O in Hg in Hg in Hg kPa kPa kPa psi
0.8826 0.1912 25.4 3.386 0.01 0.145 7.5 0.0703
in Hg psi mm Hg kPa dyne/cm2 psi mm Hg kg/cm2
36
→ ←
1 29.57 7.48 0.0283 128 3.785 0.8333 1000
to get Divide ml ml gal m3 oz (fluid) liters imp gal liters
Conversions Flow Rate 1 GPM (gallons per minute) = 3.78 L/min (liters per minute) = 0.83 Imperial GPM = 1.43 barrels per hour = 0.227 m3/h (cubic meters per hour) Weight 1 pound = 453.5 grams = 0.454 kilograms
Liquid Volume 1 gallon = 231 cubic inches = 3.7853 liters
Pressure 1 atmosphere = 14.7 psi 1 PSI = 0.07 kg/cm2 = .069 bar
1 Imperial gallon = 2.77.42 cubic inches = 4.546 liters 1 U.S. Barrel = 31 1/2 gallons water or equivalent = 42 gallons oil 1 British barrel = 36 Imperial gallons
Mesh to Microns 20 Mesh = 840 Microns 40 Mesh = 420 Microns 80 Mesh = 177 Microns 100 Mesh = 149 Microns
Temperature °C = (°F-32)/1.8 °F = (°Cx1.8)+32 °K = °C + 273.2 °Rankine = °F + 459.67 To find coefficient of expansion: Coefficient of expansion = SGH -SGL x 1 -----------------SGAVE (∆t)
1 pound of water = 27.68 cubic inches = 0.1198 gallons
SGH = Specific Gravity at high temperature SGL = Specific Gravity at low temperature SGAVE = the average or mean specific gravity at high & low temperature t = Temperature difference (high - low) in °F
Coefficients of Expansion of Common Liquids Liquid Acetone Aviation Fuel Butane Diesel Fuel Ethanol Ethylene Glycol Gasoline Hexane JP-4 Kerosene
COE * Per °F Per °C 0.0008 0.0005 0.00109 0.0005 0.0006 0.00036 0.0006 0.0007 0.0005 0.0005
0.00144 0.0009 0.00196 0.0009 0.00108 0.00065 0.00108 0.00126 0.0009 0.0009
Liquid LPG Lube Oils MEK Methyl Alcohol Naphtha NH3 Propylene Glycol Toluene Unleaded Gasoline Xylene
COE * Per °F Per °C 0.0017 0.0004 0.00073 0.00066 0.00072 0.0013 0.0004 0.00061 0.0006 0.0006
* COE = Coefficient of Expansion
Example: Compute volume change for Liquid Propane Gas (LPG) given a temperature change of 20°F. LPG coefficient of expansion: 0.0017/°F (∆t) (COE) (100) = % volume change (20°F) (0.0017/°F) (100) = 3.4% A 20°F change in temperature will result in a 3.4% change in volume.
37
0.00306 0.00072 0.0013 0.00119 0.0013 0.00234 0.00072 0.0011 0.00108 0.00108
National Electrical Code (NEC) Ratings Hazardous Classifications: Class I: Areas in which flammable gases or vapors may be present in the air in sufficient quantities to be explosive
Class III:
Areas made hazardous by the presence of easily ignitable filings or dust, but which are not likely to be in suspension in the air in quantities that are sufficient to ignite
Group A:
Atmospheres containing acetylene
Group B:
Atmospheres such as butadiene, ethacrolein, or hydrogen (or gases or vapors equivalent in hazard to hydrogen, such as manufactured gas)
Group C:
Atmospheres such as cyclopropane, ethyl ether, ethylene, or gas or vapors of equivalent hazard
Group D:
Atmospheres such as acetone, alcohol, ammonia, benzene, benzol, butane, gasoline, hexane, lacquer solvent vapors, naphtha, natural gas, propane, or gas or vapors of equivalent hazard
Explosion-proof: Enclosures or housings are designed to withstand internal explosions and prevent the spread of fire to the outside.
Class II: Areas made hazardous by the presence of combustible dust
Intrinsically-safe: Systems designed in which electrical energy in the circuits is not present at levels that would ignite a flammable mixture of a gas and air.
Group E:
Atmospheres containing combustible 1) metal dusts, regardless of resistivity 2) dust of similarly hazardous characteristics having a resistivity less than 100 k -cm 3) electrically conductive dusts
Group F:
Atmospheres containing combustible 1) carbon black, charcoal, or coke dusts having more than 8% total volatile material 2) dusts so sensitized that they present an explosion hazard, and dusts having a resistivity greater than 100 -cm but less than or equal to 1 x 108 â„Ś -cm
Group G:
Atmospheres containing combustible 1) dust having resistivity equal to or greater than 100 k -cm 2) electrically nonconductive dusts
Division 1:
Atmospheres where hazardous concentrations exist continuously, intermittently, or periodically under normal operating conditions
Division 2:
Atmospheres where hazardous concentrations exist only in case of accidental rupture or breakdown of equipment
38
International Protection (IP) Ratings The IP rating system provides a means of classifying the degrees of protection from solid objects and liquids afforded by electrical equipment and enclosures. The system is recognized in most European countries and is set out in a number of British and European standards. First Number Protection against solid objects 0 no special protection provided 1 protected against solid objects up to 50 mm 5 protected against entry of dust in sufficient quantity to interfere with operation of equipment 6 totally protected against entry of dust
NEMA enclosure type no. 1 2 3 and 3S 3R 4 and 4X 5 6 and 6P
NEMA/IEC Enclosure Ratings
Second number Protection against liquids 0 no special protection provided 1 protected against vertically falling drops of water (e.g. condensation) 2 protected against direct sprays of water up to 15째 from the vertical 4 protected against water sprayed from all directions - limited ingress permitted 6 protected against strong jets of water - limited ingress permitted 7 protected against the effects of immersion between 15 cm and 1m
IEC enclosure class
NEMA definition
General-purpose. Protects against dust, light, and indirect splashing but is not dust-tight; primarily prevents contact w ith live parts; used indoors and under normal atmospheric conditions. Drip-tight. Similar to Type 1 but w ith addition of drip shields; used w here condensation may be severe (as in cooling rooms and laundries). Weather-resistant. Protects against w eather hazards such as rain and sleet; used outdoors on ship docks, in construction w ork, and in tunnels and subw ays. Intended f or outdoor use. Provides a degree of protection against f alling rain and ice f ormation. Meets rod entry, rain, external icing, and rust-resistance design tests. Watertight (w eatherproof ). Must exclude at least 65 GPM of w ater f rom 1-in. nozzle delivered f rom a distance not less than 10 f t f or 5 min. Used outdoors on ship docks, in dairies, and in brew eries. Dust-tight. Provided w ith gaskets or equivalent to exclude dust; used in steel mills and cement plants. Submersible. Design depends on specif ied conditions of pressure and time; submersible in w ater; used in quarries, mines, and manholes.
IP10 IP11 IP54 IP14 IP56 IP52 IP67
7
Hazardous. For indoor use in Class I, Groups A , B, C, and D environments as def ined in the NEC.
-
8
Hazardous. For indoor and outdoor use in locations classif ied as Class I, Groups A , B, C, and D as def ined in the NEC
-
9
Hazardous. For indoor and outdoor use in locations classif ied as Class II, Groups E, F, or G as def ined in the NEC
-
10
MSHA . Meets the requirements of the Mine Saf ety and Health A dministration, 30 CFR Part 18 (1978)
-
11
general-purpose. Protects against the corrosive ef f ects of liquids and gases. Meets drip and corrosion-resistance tests General-purpose. Intended f or indoor use, provides some protection against dust, f alling dirt, and dripping noncorrosive liquids. Meets drip, dust, and rust resistance tests. General-purpose. Primarily used to provide protection against dust, spraying of w ater, oil, and noncorrosive coolants. Meets oil exclusion and rust resistance design tests.
-
12 and 12K 13
NOTE: NEMA standards meet or exceed IEC standards; therefore, the conversion does not apply in the opposite direction.
39
IP52 IP54
Corrosion Data NOTE: The following chart is intended only as a guide to the engineer in the selection of materials for corrosive service. Liquid Controls cannot accept responsibility for problems arising from the use of this data. We suggest that in critical applications, tests be conducted to verify the ratings.
No one material can be expected to resist the corrosive action of the wide variety of media found in the complex industries of today. However, experience and research have indicated that certain materials will perform satisfactorily under certain conditions and within certain limits. The physical properties of a material are affected differently by each corrosive medium and it is sometimes necessary to sacrifice values in one property to gain a maximum value in another property. It is necessary, therefore, that the user decide, based on experience, which property is of prime importance for the application. Although most of the suggested ratings in the following chart are based on experience, it is strongly recommended that, if any question exists regarding the expected performance of a material in a given application, actual tests be performed to determine the suitability of the materials in questions.
Explanation of Ratings A = Excellent
C = Poor
B = Good
D = Do not use
Blank = No Information NOTE: Ratings are based on media at room temperatures unless otherwise specified.
When using the table, please remember that in any given case many factors such as solution, concentration, temperature, degree of agitation and presence of impurities may influence the rate of corrosion.
40
Ratings: A - Excellent
B - Good
C - Poor
A D D C B D D D
D D
D B A A
D D D D D C B A B
D D B
B C
B B B
B D D
B D C
B D C
A A A B A B A A A A C D C A C D B B A A A A A A A B B B B C B
D - Do not use
B C B
C A A A
C A
B D B B B A B B A A A A A A A A B B B B A
A A B A B B B A A C B B B B C B C C B B B B B B B B B B D
A A B A A A A B A A A B B A A B B A A A B A A B B B B B
B B
C A A D A D D A A A A A A A A A A D A D C C D
B A D B B B C
D D C C D D D
B B B C B B
Blank - No information
41
D D D D
B C
D C D D C D D D
C A D D A
D D D D A
D A A C B A
C A B A D A
A A A A A A
A C A
B D B D
D D A A D C D
D B D
C A C D B D D D C C D A B B C B B B A B
A A B
D A A A A D
D B B B
A C
B A D
B B D
D A D
B B C
B A
B
D B D C C D C D C D C D D D C B D A C B C B B B A B A D B B A A B B A D B C B A
B A A
D D A
D D B
B B A
A A B
B A A
B A
A A A
B
B B B B B B B B A
A A A A A A A A A A A A A A
A B D A B B B B
D B
A A A A A A A A A A A A A A A A C A B A A A A A A A A A A A A A A B A A A A A A A A .A A A A A A A
UHMWPE
Grafoil
C
Nylon
B
Neoprene
D D
A
A B B A B A A A A A A A
A
D A D C C D D D D D D D D D D B C D A C B D A B C B B A D B B A A B
Hypalon
C
A
D B B C B A A B A
Viton
A D A A B B A B B B B B
D A A D A D C A C C A B B B B B
A A A B B A A
EPDM/EPR
D A A
A A
A A A B
A A A A A A A A A A A A A A A A
Delrin/Lubetal
D C C
A
Buna N (Nitrile)
D C C
A A A A A A D B A A
A
Hastelloy C
C C C D D A A A B D A A B B A B B B B A A D B
A B A A A A D A A A D B A A C A B A
Monel
C B B D D C
Alloy 20
C B A D D C
17-4PH
C B B D B C
316 Stainless Steel
Ductile Iron/Cast Iron
A cetaldehyde A cetamine A cetate Solvents A cetic A cid, aerated A cetic A cid, A ir Free A cetic A cid, crude A cetic A cid, glac ial A cetic A cid, pure A cetic A cid, 10% A cetic A cid, 80% A cetic A cid V apors A cetic A nhydride A cetone Other Ketones A cetyl Chloride A cetylene A cid Fumes A cry lonite A ir A lcohol, A myl A lcohol, Butyl A lcohol, Diacetone A lcohol, Ethyl A lcohols. Fatty A lcohol, Is opropyl A lcohol, Methyl A lcohol, Propyl A lumina A luminum A cetate A luminum Chloride dry A luminum Chloride solution A luminum Fluoride A luminum Hydroxide A luminum Nitrate A luminum Oxalate A lum (A luminum Potassium Sulf ate) A luminum Sulf ate A mines A mmonia, A lum A mmonia, A nhydrous Liquid A mmonia, A queous A mmonia, Gas, hot A mmonia Liquor A mmonia Solutions A mmonium A c etate A mmonium Bicarbonate A mmonium Bromide 5% A mmonium Carbonate A mmonium Chloride A mmonium Hydroxide 28%
Carbon Steel
Chemicals
Brass
Corrosion Data
D
C A C C A
A
A
A A A A A A A A
A
A A A A A
Ratings: A - Excellent
B - Good
C - Poor
C D B A A B B B B B D A C B B B B C A D B
C C C D B A B D
C C D D D B B B D
D - Do not use
B
A
A
B A
A
A A B A B B A A A A A A
B D A A B B D B B B C A A B A B B D B A
A B B
B A A A
B B A A A
A B B B A A C B
B A
B A
D B
B
A A
Blank - No information
42
A
A
A
A
A
A
B A
B A A A B D A D D C B A D
B A
C A A A A B A D C D C A D D A C C A A B
A A B B D C C B D D B D D A A B
B B
A A A A A B
D D D C B D A B D D A B B
B
A
B
B A B B A D D B B B A
A A A A D B B B B B A
B B C C D D D B B B B
A B B A D
D B B B D
c D
A A D A B A B A
B D
A D
D A D D D
A B A B B A D D C B A B D
A C
B
A A A A
A A A A A A A A A A A D A A A A A A A A A B A A A A A A A A A A A A A A A A B A A A A A A
D B B
A
A
B A A A A D D
C B D C B C D D B , C B A B A D
UHMWPE
A
Grafoil
A
Nylon
Delrin/Lubetal
D D .A D A D D A C A A A A A B A A B A D A D A D D C A A A D D D A A D D A C A B A A A B A A A A A A A A A B A A A D A D C C A B A D D B A B A A A B A D B A A D D B A C A B A B A A A D B
Neoprene
A
B B B
C
Hypalon
C C D D C D B B B C
B
B B B
Viton
D D D C D C C
A
C B D B D C C C B B D B B B A A
EPDM/EPR
C D C C C D C B B D C C D A D A A B B C D C
A B B A A B B B B B B A A A A A B A B A A B C B A A A A B A A A A B A B A
Buna N (Nitrile)
D
A
Hastelloy C
D
B A D A A A D B D B D B D B D B C A C B B A C B C A D B D B B A D B B A B A B B C B C B A B B A C A D B D A B A C A B B D B B B C D A C A A C B D B B B C B D D B A B A -B A A D A B B
Monel
C
Alloy 20
C
17-4PH
D
316 Stainless Steel
Ductile Iron/Cast Iron
A mmonium Hydroxide Concentrated A mmonium Monosulf ate A mmonium Nitrate A mmonium Oxalate 5% A mmonium Persulf ate A mmonium Phosphate A mmonium Phosphate Di-basic A mmonium Phosphate Tri-basic A mmonium Sulf ate A mmonium Sulf ide A mmonium Sulf ite A myl A cetate A myl Chloride A niline A niline Dyes A pple Juice A qua Regia (Strong A cid) A romatic Solvents A rsenic A cid A sphalt Emulsion A sphalt Liquid Barium Carbonate Barium Chloride Barium Cyanide Barium Hydrate Barium Hydroxide Barium Nitrate Barium Sulf ate Barium Sulf ide Beer Beet Sugar Liquors Benzaldehyde Benzene (Benzol) Benzoic A cid Berryllium Sulf ate Bleaching Pow der w et Blood (Meat Juices ) Borax (Sodium Borate) Bordeaux Mixture Borax Liquors , Boric A cid Brake Fluid Brines, saturated Bromine, dry Bunker Oils (Fuel) Butadiene Butane Butter Buttermilk Butyl A cetate
Carbon Steel
Chemicals
Brass
Corrosion Data
A A A A A A
A A A D A
C A
A A
A A A A D D A A A
A A D D D A A B D
Ratings: A - Excellent
B - Good
C C C C B B B C A D A C D C A
A D D D C C
C B
D B B A D B D B B
B C C C B B B C C D D C
C - Poor
C C B B B B B D D
A D D D C C C C C C C B B A B B D B C D C B B B C C B B C B B C D C D
C B
D D
D D
B A B C B D
D
C D C B B D
C B B D
D - Do not use
B
B
B B A B A A
D C B
C D
C
A B B B B B B B B B B A C A B A B A A A A B B A A A A A A A A A A B A B B C B A A A A A A A A A A
A B D B B B A
B C B C B B A B A A B C A B A B A B D A B A B B B C D B A B A B B A B A C
A B B A A
B
A A B A
B A D A B B A B B
A
B
D C A A B A A B B B A B B B B A D C B B D D B A B C D A D B C D D B D B D D B B A B A A C A C
Blank - No information
43
A A D A D A A C B A A A A A A A A A A A A B A A D D C A A D D B A D B D D C A A A A A A A D A D A
D C D B B B A B B B B
D C A A B A A
B B B A D B B B D D B B
B B B A A B A B B B B A
B B D D
B D A C A B A B B D B C C B
A A
A A B A A
D C B B B B B B B B B B B C D D D B B C D D B B B B D B D B C D D B D B B B B D A D D D C
D D B
B A D
C C D
D D D B D B C C B B
B B A
D C A A B A B B B B A B B B B A D B B D D D B B B D B D A D D D B D B D D B A A B C A D B C
A D
A A A A B A A B A A A A A A A A A A A
A D A
A A A A
A D D A B D D D D
B
D C
A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
UHMWPE
Neoprene
Hypalon
Viton
EPDM/EPR
Delrin/Lubetal
Buna N (Nitrile)
Hastelloy C
Monel
Alloy 20
17-4PH
316 Stainless Steel
A B B B B B B B B B B A B A B A B A B A A B B A A A B A A C B A A B B A C C B A B B A B A A A A A A
Grafoil
A C C C D B C
Nylon
Butylene Butyric A cid Calcium Bisulf ite Calcium Carbonate Calcium Chlorate Calcium Chloride Calcium Hydroxide Calcium Nitrate Calcium Phosphate Calcium Silicate Calcium Sulf ate Caliche Liquor Camphor Cane Sugar Liquors Carbonated Beverages Carbonated Water Carbon Bisulf ide Carbon Dioxide, Dry Carbolic A cid Carbon Monoxide Carbon Tetrachloride, dry Carbon Tetrachloride, w et Casein Caster Oil Caustic Potash Caustic Soda Cellulose A cetate China Wood Oil (Tung) Chlorinated Solvents Chlorinated Water Chlorine Gas, dry Chlorobenzene, dry Chlorof orm, dry Chlorophyll, dry Chlorosulf onic A cid, dry Chrome A lum Chromic A cid<50% Chromic A cid>50% Chromium Sulf ate Cider Citric A cid Citrus Juices Coca-Cola Syrup Coconut Oil Cof f ee Cof f ee Extracts, hot Coke Oven Gas Cooking Oil Copper A cetate Copper Carbonate
Ductile Iron/Cast Iron
Chemicals
Carbon Steel
Brass
Corrosion Data
D A A A A A A A D
A D A A D D A
C D D
D A A
A A A A A
Ratings: A - Excellent
B - Good
B A B B B B
A B B
B A
B A
A B C C A B B B C B A B C
B C B B C - Poor
B B B C
B B B B
C C A B C
C C B C C
B D
B B D
B B
B B C B
D - Do not use
B B B A A A C A B A A A B A B B
B C A B B B B B B B B B B B B B B B A B
B A A B B B A A B
Blank - No information
44
C D D A
B D
A B
B B
D A D
D D C
B B D D D B B A A B
B D D B D D B D B
A A C D D
D
B B B D D A D D B A
D D D
D D C C C D B C B D A D D B C
D D D
D B D D B
B B D D B B D D C C D A C D B D D B D C D B B A B D D D D B C C A D B D D C B
A A
B
C
B
A A B A A A A D
UHMWPE
B B B A A A C A B A A A B A B B
B B B
B B D D D C D A C D
A B A
A
Grafoil
B A B A A A B
A B
B D
A C C D D D C
A A A C B D D D B B
Nylon
B A B A A A B
B B
A B C D B B D D A B D A C B B D B B D A D A B A A D D D C B C C D D A D D B B
B
Neoprene
A A
B B C B A B
D B B B B B
B A A A B D A B A A
Hypalon
A
B D A
B B A C C D D D D
Viton
B
B
A A A A A D D D A A D A D A A A A D D A A C A A A C C A A A A A A A A A C C B A A A A A C A A A A A
EPDM/EPR
A D A B B B
B B B A D
A
A A A A A D C D A A
Delrin/Lubetal
B D C B
C D C B B
Buna N (Nitrile)
B C B B
B B B B B B A A A A B A A A B B B A A B A B A
A B B B B B B B A A A A B A A A B B B A A B A B A
Hastelloy C
B C C B
A B B B B B B B A A A A B A A B B C B A A B A B A D B A B A A A B A B B A B A B B A B A B B B A B B
Monel
D D D C C
Alloy 20
D D C C
316 Stainless Steel
D D D B B
17-4PH
Copper Cyanide Copper Nitrate Copper Sulfate Corn Oil Cottonseed Oil Cresol Creosote Oil Cresylic Acid Crude Oil, sour Crude Oil, sw eet Cupric Nitrate Cutting Oils, Water Emulsions Cyanide Plating Solution Cyclohexane Cyclohexanone Detergents, synthetic Dextrin Dichloroethane Dichloroethyl Ether Diesel Oil Fuels Diethylamine Diethyl Benzene Diethylene Glycol Diethyl Sulfate Dimethyl Formamide Dimethyl Phthalate Dioxane Dipentane (Pinene) Disodium Phosphate Dow therm Drilling Mud Dry Cleaning Fluids Drying Oil Enamel Epsom Salts (MgSo4) Ethane Ethers Ethyl Acetate Ethyl Acrylate Ethyl Benzene Ethyl Bromide Ethyl Chloride, dry Ethyl Chloride, w et Ethylene Chloride Ethylene Dichloride Ethylene Glycol Ethylene Oxide Ethyl Ether Ethyl Silicate Ethyl Sulfate
Carbon Steel Ductile Iron/Cast Iron
Chemicals
Brass
Corrosion Data
A B A A A A A A A A B A
A A A A A D D A
A A A A A
C D A A
A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
A
A
D C
D D D A C
Ratings: A - Excellent
B - Good
C - Poor
A C B B A A A A B B A A A B B D B . C B A B A
A D B B B A A A B B A D B A C
D B
B D B B B B A B B B B D B B B B B C A B B B A
A B B A B A A A A A A A A B A B B B A A A A A
C B A B B A
D - Do not use
A B D A
B
B
A
A A
A A A A A A A
A A B B B A B B B
B B B A B B B B B B B B
B B B B B B A A B A B A B C A B A B A B B B B B B A
D
A
D
B
A
A A
A A
B A
A A
C
A A B
A A B
B B B
A
D
A
D
A A C B B
A A B A A A A A A A
C D C A A D D A A A A A A A A A A A A A A A A A A A A A A A A A C C A A A A A A
D
C
C B
C D
C C A D D C B A D
B A C D D D D C D A A
B B C C B C
A A A A A A A A
A A A A A A
A
B B
A A A A A A A A A D
A A A A
C A C B B D D C C B D D B B A A B D B A A B C C C C C C A A A C A B B A B A A A
Blank - No information
45
C
UHMWPE
Grafoil
D A D D D B
Nylon
B A B B B B B A B A B D B B
A A C B A
Neoprene
D B D D D B C B C B C D D B
B
D B B
Hypalon
B
D B B B A A B
Viton
D D C B B
B
B B A A
EPDM/EPR
B D B D C C C B . BB
B B
A
Delrin/Lubetal
D D
B A D D
Buna N (Nitrile)
D D
A A 'A A B D B A B A A A A B A B A B A A A A A A B A A A A B B B A A A A A A A A A A A
Hastelloy C
D D
A A C B B D B A B A B A B B A C B B A A A A A A C A A
Monel
D
Alloy 20
D
17-4PH
C
316 Stainless Steel
Ductile Iron/Cast Iron
Fatty Acids Ferric Hydroxide Ferric Nitrate Ferric Sulfate Ferrous Ammonium Citrate Ferrous Chloride Ferrous Sulfate Ferrous Sulfate, Saturated Fertilizer Solutions Fish Oils Flourine Gas, dry Flue Gases Fluoboric Acid Fluorosilicic Acid Formaldehyde, cold Formaldehyde, hot Formic Acid, cold Formic Acid, hot Freon Gas, dry Freon 11, MF, 112, BF Freon 12, 13, 32, 114, 115 Freon 21, 31 Freon 22 Freon 1 13, TF Freon, w et Fruit Juices Fuel Oil Fumaric Acid Furfural Gallic Acid 5% Gas, Manufactured Gas, Natural Gas, Odorizers Gasoline, Aviation Gasoline, Leaded Gasoline, Motor Gasoline, Refined Gasoline, Sour Gasoline, Unleaded Gelatin Glucose Glue Glycerine (Glycerol) Glycol Amine Glycol Graphite Grease Helium Gas Heptane Hexane Hexanol, Tertiary
Carbon Steel
Chemicals
Brass
Corrosion Data
C C D
D D D A A B A D A B D B D D D
D A A A A A A A A A A A A A B D A B A B A A B
B B B
B C C D C B
B D D C B B B B A C B B D B B B C
C B C C B B A C C A D B C B A C B C B A A B D D D C D D A A A D A B B B B C C
A
A A D A A A A A A D
A A A A A A A A A A A A A
A A A A A A A A B A A A A A
A A
A A A A A A A A A A A A A A A A A A A A A
A A A A A A
A D D A
D D D D D D A A A A A
A C D A
Ratings: A - Excellent
B - Good
C - Poor
A
D C C D C A C C
D D B B D D B C D A D B
D D B D C A D C
A
A
B
A A A A A D A A D D D D B B B C C C B B B A B D B D B B B D
A A A A B D A C D D D D
C B B
B B A A B D A C D D D D C A C D D C B A B B A B B D B D B B
B B
B B
B C
C D
B A B A B
D - Do not use
A B A C A B B B A B B A A A B A B A A A A A A A A A B A A B A B B B B A A B B A B A B A B A A A A B
B
D D B D
C A A A
A B A B A A B B B B B A A A B A A A A A A A A A A A A A A B A A B B B A A A B A B A B A B A A A A B
A D C B A D D B C B A B C
B
A D D B D
A B A A A A B A A D D C D B B B B B B B B B B B B B B B B A B B B
A A A A A
A B A B
A B B A A
A C B B B B D A C C A C A B A D C A B A A A D D B C B C B B A A B D B A B A A B B B B A A B B A B
Blank - No information
46
A D D A A A D D C C A A A A A A A A A A A A A A A D D D D A A A A A A A A A A A B A A A A A A A A A
D B B B B B B B A B A D B D D D D
D D D B B B B C B B B D D D B D D B B B B A A
A D
B A A A A A A A
B
A
B
D A A A A A D D A B A D B
D
A B B B B A B A A B B B B A A A B A A
B B D B
D B D D B B B B D B D D B B D C B B B B A A B B A D
B C B B B B D B A B A C B D C D C C C C C A D D A C A D C C B B B D B C B B B B B B B A A B A A B
UHMWPE
Grafoil
C B B B
Nylon
A D A A A
:
Neoprene
EPDM/EPR
Delrin/Lubetal
Buna N (Nitrile)
Hastelloy C
Monel
Alloy 20
17-4PH
316 Stainless Steel
B D C D B
Hypalon
B D D A B
Viton
Hy draulic Oil, Petroleum Bas e Hy drazine Hy drocy anic A c id Hy drof luos ilic ic A c id Hy drogen Gas , c old Hy drogen Gas , hot Hy drogen Perox ide, Conc entrated Hy drogen Perox ide, Dilute Hy drogen Sulf ide, Dry Hy drogen Sulf ide, Wet Hy po (Sodium Thios ulf ate) Illuminating Gas Ink-New s print lodof orm Is o-Butane Is o-Oc tane Is opropy l A c etate Is opropy l Ether J P-4 Fuel J P-5 Fuel J P-6 Fuel Keros ene Ketc hup Ketones Laquer (and Solv ent) Lac tic A c id Conc entrated c old Lac tic A c id Conc entrated hot Lac tic A c id Dilute c old Lac tic A c id Dilute hot Lac tos e Lard Lard Oil Lead A c etate Lead Sulf ate Lec ithin Linoleic A c id Lins eed Oil Lithium Chloride LPG Lubric ating Oil Petroleum Bas e Ludox Magnes ium Bis ulf ate Magnes ium Bis ulf ide Magnes ium Carbonate Magnes ium Chloride Magnes ium Hy drox ide Magnes ium Hy drox ide Hot Magnes ium Nitrate Magnes ium Sulf ate Maleic A c id
Ductile Iron/Cast Iron
Chemicals
Carbon Steel
Brass
Corrosion Data
A A A D D D D
A
A A A A A
A
C D D A
A A A /D C A A A A A A A A A A A A A A A A A A A A A A A A A
A A C A A A
A
C
A A A A A A A
A A A A A
C
A A A A A A B A A
A A A A A A A
A
Ratings: A - Excellent
B - Good
B D D B D D D D A A A D C A
D D
D D
D B D D
B
A B B A B D B
B A A A
B A B C
B A B C
B B B D A A
D B B C A C
D B B C A C
B B B B D D D D B D D D D D B A
B B B B B D D D D C D D D D C B A
B A B B B D D D D A D D D D D D A C - Poor
D
A B B A B
B B A B A A A C A B A A A A A A A B A A A A A B A A A B B A A A B A A B B A A B B B A A A C A A A A
D - Do not use
A D D D D
B B B A A A A C A B A A A A A A A A A A A A A A A A A B B A A A B A A B B A A A A A A A A B A A A A
B B A
B
B B
B D C D B B B A C B B
B B
D A A B B A B B B A A
B A B C A A
A A D D D B C D D D D D D A A A D A A
B B A B B D C B B B A D D D D D B A
D D A B D A A A A A D C C D D D D A
B A B B
B A A B B B B B B
A B A A B
B
Blank - No information
47
C A A A A A A A C A A A A A B B A A A A A A A A A A A A D A A A C A A A A A C D C C C D D D D D B A
D B B
D A A
B A A
D
D B A
B A
B
B A B B B B B
B D D B B B B
B A B D B
B A A B A A D D D B D
D B D B
B D C D
D D D B
A D
A A A B A A
B C
A
D
B D D D B B A B D B D D D C B
D A A A A D A A A B A A B B A C A
D D D D D
D B
D C D D B B B B D D D C D D B
A B D D D D D D D D D B D A B C D A A D D A C D A B A A A D B C D D D D A
C
A A A B A A A
A
C A A
A A A A C A D D D D D A
A A A A A A A A A A A B A A A A A A A A A A A A A A A A A A A A A A A A A A A B A A A B C D D A A
UHMWPE
Grafoil
Nylon
Neoprene
Hypalon
Viton
EPDM/EPR
Delrin/Lubetal
Buna N (Nitrile)
Hastelloy C
Monel
B D
Alloy 20
D
17-4PH
B B
316 Stainless Steel
Ductile Iron/Cast Iron
Maleic A nhy dride Malic A c id Malt Bev erages Manganes e Carbonate Maganes e Sulf ate May onnais e Meat Juic es Melamine Res ins Methanol Merc uric Chloride Merc uric Cy anide Merc urous Nitrate Merc ury Methane Methy l A c etate Methy l A c etone Methy lamine Methy l Bromide 100% Methy l Cellos ov e Methy l Cellulos e Methy l Chloride Methy l Ethy l Ketone Methy lene Chloride Methy l Formate Methy l Is obuty le Ketone Milk & Milk Produc ts Mineral Oils Mineral Spirits Mix ed A c ids (c old) Molas s es , c rude Molas s es , Edible Moly bodic A c id monoc hloro Benz ene Dry Morpholine Mus tard Naptha Napthalene Natural Gas , Sour Nic hel A mmonium Sulf ate nic kel Chloride Nic kel Nitrate Nic kel Sulf ate Nic otinic A c id Nitric A c id 10% Nitric A c id 30% Nitric A c id 80% Nitric A c id 100% Nitric A c id A nhy drous Nitrobenz ene Nitrogen
Carbon Steel
Chemicals
Brass
Corrosion Data
A
A A A A
D
D D D
B D D B B
D D A A A A A A A D D D A
Ratings: A - Excellent
B - Good
C - Poor
A B C A
A A B B
A A C B
B C D C B A A B A B B B A B
C B
B B
C D D B D B A C A C C B B B
A C B B D D D D D D
B B C D A D D D B C
B B C D A D D D B C
B B G C B
B C C D C B
C C C D C B
B D B A C A C C
D B B
C C
B B B
D D
D D
D - Do not use
B A B A A A A A B B B B A B A A A A B B A A B B A A B A A D B D A B A A B B B A A A B B B A A A B A
D A
B B B D C D
C
C
B A B A A A A A B A B B A B A A A A B A A A B B A A A A A B B B B B A A B B B A A A A B B A A A B B
D D D B A A A B C D A B A A A A B A B A B B B A A A D C C A
A A D A B
C B A A A A B B
A A A
A
B A
B A B
B B B B A B D B
Blank - No information
48
B B A A B A D B D C A C B D D D B B B A B B A D A D D B B B C C D D C C C A A C B
B B B A A
B B A A A A A A C C D D A C D C C A A A A A A A A B A C A D D D D D B D B A D A A A D A A A B A A A
D B D D
D D D B B A A B D B D B D D D D D D A B B B
B
B D D B B B
B B
A
A
A
B
B A A A C A C A A A A B B B A A B A
A A A B A A A B B B A A B A A B
B A A A
C B B
D B D B B A A B D D D B B
D D B B B B B
B B B B D C D D B B B D D D B B B C B B B D B D
B B B
A B B C C D D C C A A D C B C C
C C B
B B A A
B D D
A A A A A A A A D D A D D D D D A A A
A D A D D D D D D D A A B
A A A A A A A A A A
A A D
A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A
UHMWPE
Grafoil
Nylon
Neoprene
Hypalon
Viton
EPDM/EPR
Delrin/Lubetal
Buna N (Nitrile)
Hastelloy C
Monel
D C C
Alloy 20
D B B
17-4PH
D D B
316 Stainless Steel
Ductile Iron/Cast Iron
Nitrous A c id 10% Nitrous Gas es Nitrous Ox ide Oils &. Fats Oils , A nimal Oils , Petroleum Ref ined Oils , Petroleum Sour Oils , W ater Mix ture Olaic A c id Oleic A c id Oleum Oleum Spirits Oliv e Oil Ox alic A c id Ox y gen Oz one, Dry Oz one, W et Paints & Solv ents Palmitic A c id Palm Oil Paper Pulp Paraf f in Paraf ormaldehy de Paraldehy de Pentane Perc hlorethy lene, dry Petrolatum (V as eline Petroleum Jelly ) Phenol Phos phate Es ter Phos phoric A c id 10% Phos phoric A c id 50% Cold Phos phoric A c id 50% Hot Phos phoric A c id 85% Cold Phos phoric A c id 85% Hot Phos phoric A nhy dride Phos phorous Tric hloride Phthalic A c id Phthalic A nhy dride Pic ric A c id Pineapple Juic e Pine Oil ' Pitc h (Bitumen) Poly s ulf ide Liquor Poly v iny l A c etate Poly v iny l Chloride Potas s ium Bic arbonate Potas s ium Bic hromate Potas s ium Bis ulf ate Potas s ium Bis ulf ite Potas s ium Bromide
Carbon Steel
Chemicals
Brass
Corrosion Data
C D A A A C C
A C
A D A A A A A A A A D
A
A
Ratings: A - Excellent
B - Good
C - Poor
B C B B B B B A B B B B
B C C C A B B A C B B A A B B B B B B B B
B C A A C B B B B B B B B B
A
C
C
A A B A A A B C B B
A A C A B A C D C
A A C A B A C D C D
C C A B
D C A
D D
D
D D B B D D
D - Do not use
B B C C D B B B
A
A A
B B B
A
C
B C B B B B B A A A A A C B B B B B B C C A B B B
B B
B B B B
A B A
B
A A A B A A A A A B B C A A A A A B A A B A A B A D A A
B A
C
A A A A
B B D B
A B B A B
D A A A A
A B A
A A A B
B B D
Blank - No information
49
B C
A A A A A A A A D D D D A A A A A A A A A A A A C D A A A A A A A A A C A A A A C A B A A D D A
B B A B A B B
B
A A A B A A A A D D
A B B
A A
B A B B A B A D D B B
B B B B B
B B A B
A A A
B B
A B B A A B A D A A
B B B B D B
B
A D
A A A A A A A A B B B B A A A A A B A B B B B B A D A B C
B
A A B A A D A A A B
A B
A B
C B
B
B
A C A B
B A
B B
B C
B B
A
D
B B D
A
A C A A
B B
A A A A A A A A A A A A A A
A A A A A A A
A
C C C C C A A A D
A A A A A A A B A
UHMWPE
Neoprene
Hypalon
Viton
EPDM/EPR
Delrin/Lubetal
Buna N (Nitrile)
B B A B B A B B B B B B B B A B B A B A A A B A A B A A A A A B A A A A A A A B A B B B B A B A A A
Hastelloy C
A B B
Monel
316 Stainless Steel
B B B B B B A B B B B B B B A B B A B A A A B B B B B B A A A B A A A A A A B A B B B B B A B A A A
Grafoil
B B B B B C C C A B B B C B
Nylon
B B C
Alloy 20
B B C B D D D B D D D D D B
17-4PH
Potas s ium Carbonate Potas s ium Chlorate Potas s ium Chloride Potas s ium Chromate Potas s ium Cy anide Potas s ium Dic hromate Potas s ium Ferric y anide Potas s ium Ferroc y anide Potas s ium Hy drox ide Dilute Cold Potas s ium Hy drox ide to 70% Cold Potas s ium Hy drox ide Dilute Hot Potas s iium Hy drox ide to 70% Hot Potas s ium Iodide Potas s ium Nitrate Potas s ium Ox alate Potas s ium Permanganate Potas s ium Phos phate Potas s ium Phos phate Di-bas ic Potas s ium Phos phate Tri-bas ic Potas s ium Sulf ate Potas s ium Sulf ide Potas s ium Sulf ite Produc er Gas Propane Gas Propy l Bromide Propy lene Gly c ol Py ridine Py rolgalic A c id Quenc h Oil Quinine, Sulf ate, dry Res ins & Ros ins Res orc inol Road Tar Roof Pitc h Ros in Emuls ion R P-1 Fuel Rubber Latex Emuls ions Rubber Solv ents Salad Oil Salic y lic A c id Salt (NaCl) Salt Brine Sauerkraut A rine Sea W ater Sew age Shellac Silic one Fulids Silv er Bromide Silv er Cy anide Silv er Nitrate
Ductile Iron/Cast Iron
Chemicals
Carbon Steel
Brass
Corrosion Data
C C
A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A B
A A A A A
A
A A A A A C
A
Ratings: A - Excellent
B - Good
C - Poor
D A B A B A B D
D A B B B A B D
C B B B
B C D B
C C D B
B D C C C
B C C C C
B C C C C
B C B D C
B C B B
C B B A
B C C A
B C B B A A C C C A
D - Do not use
B A C B C B C D
B
B B B B
B A A A
A
B B B A A A B A B D B B
A A A B A B B D A
A A A B C B B B B B B B B A B B B A A B
A B B B B B B B B
A B C C C C B A B B A
B
A A A A A A A D
Blank - No information
50
A A A A A A A A B A D
A A A
B D B
B B B A
A A
A
A
B B B B B B B B
A A A A A A A A
B B B B B
B
A
B
A
B B B B
A B C C C C C A
B B B B B B B
A A B A B C D
B B
A A
B
B D B B C A B B
B B
B B
B B B
A A A A A A A A A
B A A A A A A A
A B A A A A A
C B B
B B A B B B A B C B
A
B
A
A A B
A B B
A A A C
B D B B
A A A A A B A D
A A
A A
C C C C C C C B
A A A
A A A
D D A D A
UHMWPE
C A A A A A B D
B
A B B
Grafoil
B
B B B
Nylon
B
B
Neoprene
D
B B B B B C A B
Hypalon
D D C D B C C B
Viton
D D C C B C C B
A D A A A A A A A A
D A A A B B A D D A A A A A A A A A A D D D D D D D A A B A A A B A A B A A
EPDM/EPR
B B B B B B B C
B B
A B A
Delrin/Lubetal
C
A B B B B
Buna N (Nitrile)
C
A A B B B A B A B B B A B A B B A A A B A A A B B C B A B A A A B B B B B B B A B B A B A A B A A A
Hastelloy C
B
A A B A B B B A A B B A B B A B A A B A A A A A A D B A B A A A B B B B B B B A B B A B A A B A B A
Monel
B C C
Alloy 20
A C C
17-4PH
A B B
316 Stainless Steel
Ductile Iron/Cast Iron
Silv er Plating Sol. Soap Solutions (Stearates ) Sodium A c etate Sodium A luminate Sodium Benz oate Sodium Bic arbonate Sodium Bic hromate Sodium Bis ulf ate 10% Sodium Bis ulf ite 10% Sodium Borate Sodium Bromide 10% Sodium Carbonate (Soda A s h) Sodium Chlorate Sodium Chloride Sodium Chromate Sodium Citrate Sodium Cy anide Sodium Ferric y anide Sodium Fluoride Sodium Hy drox ide 20% Cold Sodium Hy drox ide 20% Hot Sodium Hy drox ide 50% Cold Sodium Hy drox ide 50% Hot Sodium Hy drox ide 70% Cold Sodium Hy drox ide 70% Hot Sodium Hy poc hlorite (Bleac h) Sodium Hy pos ulf ite Sodium Lac tate Sodium Metaphos phate Sodium Metas ilic ate Cold Sodium Metas ilic ate Hot Sodium Nitrate Sodium Nitrite Sodium Perborate Sodium Perox ide Sodium Phos phate Sodium Phos phate Di-bas ic Sodium Phos phate Tri-bas ic Sodium Poly phos phate Sodium Salic y late Sodium Silic ate Sodium Silic ate, hot Sodium Sulf ate Sodium Sulf ide Sodium Sulf ite Sodium Tetraborate Sodium Thios ulf ate Soy bean Oil Starc h Steam (212째 F)
Carbon Steel
Chemicals
Brass
Corrosion Data
A A A A A
A A
A A A A A B A
A A A A A A A
A A A A A A A A A A A A A A A A B A A A A A A A A A A A A A A A A A
A
A A A A A A A A A
A A
A
A A A A A
A A A
Ratings: A - Excellent
B - Good
C B B D C D B C
B B B D B D B C
A D C A C A A B
A D C A C B A C D
B
C - Poor
B B B
B B C
B B C
A B B B A A D A B A B C B
C B D
C B D B D C D A D B D B D
D C D A D B A D
D - Do not use
A A A B
A C
B B B
B A A
A
A
A A B
B A A A B B D A A B 'B A A B B B A B B B B A A B A A A A B B B B B A B B A A A A B A A A A A B A A
B B A B B C .B B B A D B B D D B B A B A A B A A B B B
C B B A B B B A A D A A A B B B
A A
A B B B B
B A B
B A
A A A A A A A A A A A A A A A C A A A A A A
A D A C C C D D D D D D D B D C B B B C C D A A D D C C B A A B C C A D C C B A B D B A A
Blank - No information
51
A A A A C A D A A A D A D D A D D C A A D A A A C A A A A D A C A A A A B A A B D A A A A A A A A A
B
C C C B A A
B C A B B
B D D D D D D B B D B
C C D B
B B A A B A A A
B D D B B B D B
D B
A A
D B
D
B A A D B D
D D
B
B D B
D D B
B D D B
B A A D
A D C D
D D A A B B A C A D B A A
B A D
D B C B B A C B C D B
A A D A A B B A A
B
C D A B B B B C D D D B C D D B D C B B D D B D A B D D D B B A B D B B B D B B B A B B D B A A
A A A
A A A A A A A A A A A A A D D A D A A A
C A
A D D D D A
A
A A
A A A A A A A A A
A
A C
A A
A A A A A A A A A A A A A A A A A
UHMWPE
A B A
Neoprene
B D B
Hypalon
Delrin/Lubetal
Buna N (Nitrile)
Hastelloy C
Monel
Alloy 20
17-4PH
316 Stainless Steel
B A A A B B B B D A A A B B B C A B B 'B B A A B A A A A B D B B B A B B A A A A B A A B A A A B A B
Grafoil
C C C C D B
C B B C C C C C D B
Nylon
C A B
Viton
C A A B C C C D B B D B D B B C C D B B ' A B B A C B A B B
EPDM/EPR
Stearic A c id Sty rene Sugar Liquids Sugar, Sy rups & Jam Sulf ate, Blac k Liquor Sulf ate, Green Liquor Sulf ate, White Liquor Sulf ur Sulf ur Chlorides Sulf ur Diox ide, dry Sulf ur Diox ide, w et Sulf ur Hex af luoride Sulf ur, Molten Sulf ur Triox ide Sulf ur Triox ide, dry Sulf uric A c id 0 to 77% Sulf uric A c id 100% Sulf urous A c id Tall Oil Tannic A c id (Tannin) Tanning Liquors Tar & Tar Oils Tartaric A c id Tetraethy l Lead Toluol (Toluene) Tomato Juic e Trans f ormer Oil Tributy l Phos phate Tric hlorethy lene Tric hloroac etic A c id Triethanolamine Triethy lamine Tris odium Phos phate Tung Oil Turpentine Urea Uric A c id V arnis h V egetable Oils V inegar V iny l A c etate Water, Dis tilled Water, Fres h Water, A c id Mine Wax es Whis key & Wines Xy lene (Xy lol), Dry Z inc Bromide Z inc Hy dros ulf ite Z inc Sulf ate
Ductile Iron/Cast Iron
Chemicals
Carbon Steel
Brass
Corrosion Data
A A A
A A A
B D A A
A D C D C C A D A
A A A A A D
A
LIQUID CONTROLS GROUP I D E A L
S O L U T I O N S
I N T E G R A T E D
S Y S T E M S
LIQUID CONTROLS EUROPE • LIQUID CONTROLS SPONSLER LIQUID CONTROLS • LIQUID CONTROLS INDIA FAURE HERMAN • TOPTECH SYSTEMS CORKEN • SAMPI
LIQUID CONTROLS 105 Albrecht Drive Lake Bluff, IL 60044 (847) 295-1050
LIQUID CONTROLS EUROPE/SAMPI Via Amerigo Vespucci 1 55011 Altopascio (Lucca), Italy +39 (0) 583 247600
LIQUID CONTROLS INDIA 808 VCCI Complex GIDC Makarpura Vadodara-390 101 Gujarat, India +91 265 2631855
T O P T E C H S YS T E M S 280 Hunt Park Cove Longwood, FL 32750 (407) 332-1774 Nateus Business Park Nieuwe Weg 1-Haven 1053 B-2070 Zwijndrecht (Antwerp), Belguim +32 (0)3 250 60 60
FA U R E H E R M A N Route de Bonnetable B.P. 20154 72406 La Ferté-Bernard Cedex, France +33 (0) 243 0602860 6961 Brookhollow West Drive Houston, TX 77040 (713) 623-0808
LIQUID CONTROLS SPONSLER 2363 Sandifer Boulevard Westminster, SC 29693 (864) 647-2065
A Unit of IDEX Corporation 105 Albrecht Drive Lake Bluff, IL 60044-2242 1.800.458.5262 • 847.295.1050 Fax: 847.295.1057 www.lcmeter.com
© 2007 Liquid Controls (11/07)
CORKEN 3805 Northwest 36th St. Oklahoma City, OK 73112 (405) 946-5576