HCI10-SVT_PD.pdf

HCI10-SVT HD/SD SCTE-104 ‘follow me’ cue tone inserter for SVT A Synapse® product

COPYRIGHT  2011 AXON DIGITAL DESIGN BV ALL RIGHTS RESERVED NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY FORM WITHOUT THE PERMISSION OF AXON DIGITAL DESIGN BV.

DATA INSERTION

Video Processing

Block schematic & I/O panel HCI10-SVT

HD/SD-SDI IN+ EMBEDDED AUDIO

EQ

FRAME SYNC

SCTE-104 SVT INSERTER ‘FOLLOW ME’

AUTOPHASER

HD/SD-SDI OUT + EMBEDDED AUDIO

PROC-AMP COLOR-BAR SWEEP GENERATOR

HD/SD-SDI OUT + EMBEDDED AUDIO

OSD IDENT

AUTO FORMATREF

INSERT ON/OFF GPI

HD/SD-SDI OUT RECLOCKED

-

PLL

1

µP

REFERENCE INPUTS 2

RACK CONTROLLER INTERNAL SYNAPSE BUS

BPH03

BHX03

RECLOCKED OUTPUT PROCESSED OUTPUT 1

relay bypass

HD/SD SDI INPUT (OPTIONAL FIBER INPUT)

PROCESSED OUTPUT 2 (OPTIONAL FIBER OUTPUT)

GPI INPUTS

November 2011

HCI10-SVT

DATA INSERTION

Video Processing

Features The HCI10-SVT is a SCTE-104 compatible ‘follow me’ inserter specified by SVT Sweden.

The insertion is handled according to the following document: “Teracom Inband Triggering API for local insertion v1.0 2011-10-07.pdf” In short: Triggering API for Follow Me: Inband trigger signal for Follow Me control can be sent in uncompressed video SDI/HD-SDI as SCTE104 commands with some extra private data fields or in compressed MPEG2 TS as SCTE35 with some extra private data fields.

2.1.1 SCTE104/SCTE35 commands for Follow Me triggering SCTE104/SCTE35 API for Follow Me triggering is based on support of one multiple operation command/message.

Each Follow Me control message contains exactly two operations: - a SCTE104/35 standard „splice null‟ operation followed by - a private Follow Me data operation containing the current broadcast mode. There are two broadcast mode defined up to today; o „national mode‟ referring to when all regional versions of a service contain same video content and o „regional mode‟ referring to when one, more or all regional versions of a service contain different video content.

For more details see chapters below.

2.1.2 Insertion and repetition of Follow Me commands.

The defined Follow Me command (SCTE104/SCTE35) section shall be repeated every second, even is no change of broadcast mode has occurred. Maximum repetition rate for the SCTE104/SCTE35 messages is one per 0.5s and minimum repetition rate one per 1.5s.

There is no timing information (PTS, pre-roll…) in the SCTE104 Follow Me message.

The inserter is placed after a built-in autophaser/framsync for stability and convenience.

  

  

            

GPI triggered SCTE-104 ‘follow me’ signal HD-SDI and SD-SDI compatible Formats:  1080i/50/60  1035i/60  720p/50/60/  1080p(sf)/24/25/30 Built-in proc amp 2-level, 3-level sync compatible On loss of input:  Freeze  Black  Green  Gray One reclocked output Two processed outputs I/O delay measurement Switch positioning measurement (in autophase mode) H and V delay offset adjustment with respect to input or reference Separate delay settings for 1080, 720p and SD SDI ANC blanking of H, V or H+V Test pattern (color bar/sweep) OSD ident label with maximum 10 characters (for set-up purposes) Detection and transparency for S2016 (AFD) Locks to Bi-level or Tri-level syncs Full control and status monitoring through the front panel of the SFR04/SFR08/SFR18 frame and the Ethernet port (ACP) Optional 1 fiber input (replacing 1 SDI input) or 1 fiber output (replacing 1 SDI output) on I/O panel

Applications 

Follow me advertisement insertion

November 2011

HCI10-SVT

DATA INSERTION

Video Processing

Ordering information Module:  HCI10-SVT: HD/SD SCTI-104 follow me inserter Standard I/O:  BPH03_HCI10: I/O panel for HCI10-SVT Relay bypass I/O:  BHX03_HCI10: relay I/O panel for HCI10-SVT

November 2011

HCI10-SVT

DATA INSERTION

Video Processing

Specifications HD/SD Serial Video Input Standard

Equalization Return Loss

625/50 or 525/59.94 SMPTE 259M-C (270Mb/s) with SMPTE 272M embedded audio SMPTE 292M (1.5Gb/s), SMPTE 260M, SMPTE 274M, SMPTE 296M, SMPTE 349M 1080i/59.94, 1080i/50, 720p/59.94, 720p/50 Automatic to 100m @ 1.5Gb/s with Belden 1694A or equivalent cable. > 15dB up to 1.5GHz

HD Serial Video Output Standard

Signal Level DC Offset Rise and Fall Time Overshoot Return Loss Wideband Jitter

625/50 or 525/59.94 SMPTE 259M-C (270Mb/s) with SMPTE 272M embedded audio SMPTE 292M (1.5Gb/s), SMPTE 260M, SMPTE 274M, SMPTE 296M, SMPTE 349M 1080i/59.94, 1080i/50, 720p/59.94, 720p/50 800mV nominal 0V ±0.5V 200ps nominal for HD, 750ps nominal for SD < 10% of amplitude > 15dB up to 1.0Gb/s, > 10dB up to 1.5Gb/s < 0.2UI

Reference Input through RRC Number of Inputs Tri-level Bi-level

2 on SFR18, 2 on SFR08 and 1 on SFR04 SMPTE274M, SMPTE296M 600 mVp-p nominal, 75 Ohms terminated through loop PAL Black Burst ITU624-4/SMPTE318, Composite NTSC SMPTE 170M 1Vp-p nominal, 75 Ohms terminated through loop

Miscellaneous Weight Operating Temperature Dimensions

Approx. 250g 0 °C to +50 °C 137 x 296 x 20 mm (HxWxD)

Electrical Voltage Power

November 2011

+24V to +30V <10 Watts

HCI10-SVT