INSTRUCTIONS MANUAL
ELECTRIC SCOOTER All Aluminum with Lithium Battery
CONTENTS AND FEATURES Speedometer Brake Lever Handle sleeve
T Bar Upper locker Folding hook Hoodle Middle Bar
Middle locker Set of 7pcs Light
Connecting Head Folding Switch
Brake Pad
Disc Brake
Pedal
Mudguard Front fork Front Wheel (with motor)
Brake Disc Foot Support
Rear Wheel
This product is patented. Legal liability will be pursued if copy. Please read this manual carefully before using, and operate according to the manual.
-1-
WARNING AND INSTRUCTIONS WARNING 1. Please follow local traffic regulations and national laws while riding this scooter. 2. Can not ride while visibility is low. 3. It’s forbidden to use this scooter for special effects or dangerous action performance. 4. It’s forbidden to use this scooter carrying person or goods. 5. Check before riding that all screws and fasteners are normal. 6. Make sure the folding axle enters the slot.
PLEASE NOTE: Our company is not responsible for the damages and hurts caused by using this product directly or indirectly.
IMPORTANT INSTRUCTIONS 1. Reading this manual carefully helps you to understand, use and maintain this product properly, and to understand its performance and features. 2. Please learn how to use in open flat and person-less area during preliminary learning. And safety protective clothing should be worn. 3. Before using, a range of distance should be practiced to make all parts and brake into right position.
OPERATING GUIDANCE BATTERY 1. It’s forbidden to start motor during charging. 2. Speedometer only shows battery range roughly. 3. After fully charged, the battery can not be charged for too long time. 4. It’s suggested to slow down or stop using while the battery indicator turns red in speedometer.
DO NOT USE BATTERY OR CHARGE IT UNDER FOLLOWING CIRCUMSTANCES: 1. The product is damaged. 2. Abnormal smell and heat is released from the battery. 3. While there is any liquid leakage, you should stop riding and do not make any contact with leaking liquid. And the product should be placed out of child’s contact.
CHARGER AND BATTERY 1. This electric scooter’s charging port is external. Please insert the charger to the charging port in the scooter before inserting it to the socket. 2. While the charger indicator is red, charging is normal. While the indicator turns green, the charging is finished. The battery should not be charged or out of power for long time. If the scooter is not used for long time, it’s suggested to charge the battery every half month. (around 8-9hours every time) 3. Before taking out battery for installation or maintenance, ensure the power is disconnected. Do not open the inside of battery. Do not leave battery in high temperature place. 4. Please charge this scooter with standard qualified charger. 5. Dispatch battery and carry the scooter on permissible environment, and conforming to national regulations.
TIPS: It’s dangerous while riding, please be careful to be safe. -2-
SAFETY NOTICE WARNING 1. This scooter is designed for one person use. Carrying person is forbidden. 2. Safety protective devices should be worn while riding. Two hands should be on the handlebars during riding. It’s forbidden to use one hand only. 3. Please ride after familiarizing with this product by practicing in open area. 4. Please follow local traffic laws while riding. 5. Keep two feet on the pedal during riding. 6. Please slow down while coming across area with lots of person. 7. It’s forbidden to ride on abnormal surfaces such as area with water, oil, or ice. 8. Adjust the scooter to comfortable position before riding.
TIPS: Lean forward while accelerating. Put gravity center backward while decelerating.
BEFORE START 1. Choose a flat and open area. 2. Carry out the scooter according to the manual, and adjust it to comfortable position. 3. Wear safety protective devices. 4. Make sure all fasteners are normal.
RIDING (ASSISTANCE RIDING) 1. Press
to turn on the power.
2. To ensure safety, the product is equipped with assistance start. First, put a foot on the pedal, another on the ground and kick it backward to make the scooter slid forward. Then pull the throttle switch slowly. 3. The scooter will go forward, leaving the foot from ground to the pedal, and enlarge the throttle to speed up the scooter. 4. After riding at a constant speed for 8 seconds, the throttle switch can be loosen to enter into cruise control status. Braking or accelerating will stop cruise control status.
PARKING 1. Release the throttle in your right hand. 2. Move your gravity center backward. 3. Pull brake lever slightly by both hands. Brake lever will cut off motor power immediately, and disc brake on rear wheel will work to decelerate the scooter. Put one foot on the ground after decelerating. It’s not suggested to brake heavily. Road status should be considered.
-3-
OPERATING GUIDANCE
Throttle
--- ON/OFF Button (Press this Button for 3 seconds)
---Gear Button
--- Speed display
TIME --- Time display TRIP --- Single trip ODO --- Total trip 8888.8 ---Value
-4-
HOW TO OPEN AND FOLD THE SCOOTER HOW TO OPEN: STEP 1
Open the package and remove foam packed inside. Check that the scooter is under normal conditions.
STEP 2:
Press down the brake pad by left hand, then pull the middle bar upside by right hand, to make the folding hook dispatch from brake pad. Continue to pull the middle bar to make the folding axle go into the slot totally.
-5-
STEP 3:
Push both handlebars outside to the T bar. Both folding sleeve should be in compliance with T bar totally. (You can shake a little during this process.)
STEP 4:
Release the upper locker, press the hoodle down inside the bar, and pull the T bar upside to appropriate position. After it’s in right position, lock the upper locker.
-6-
HOW TO FOLD: STEP 1:
Release the upper locker, press the hoodle down inside the T bar, and adjust the T bar downside to the lowest position. Then lock the upper locker.
STEP 2:
Pull the left and right folding sleeves both to left or right side, make them out of T bar, and fold it downside. Then move left and right folding sleeves close to the T bar.
-7-
STEP 3:
Press the pedal by right foot, push the middle bar forward by right hand, and press the folding switch to make folding axle separate from the slot. Finally, fold middle bar by right hand to make folding hook go into brake pad.
-8-
BATTERY AND CHARGER Every scooter is equipped with special lithium battery and charger. Chargers of other brands can not be used for charging. Also, the charger can not be used to charge other batteries.
LITHIUM BATTERY The battery should be charged on time after every use. If it’s not used for long time, please charge at least once every half month. If it’s not charged for long time, the battery will go into self protective status, and it can not be charged. In such case, please contact your dealer.
CHARGER The charger have over-charge protection function. Once the battery is 100% charged, it will stop charging automatically. (It’s suggested to charge 2 extra hours after fully charged. Then it can be pulled out from the socket.)
CHARGING INSTRUCTIONS 1. First insert the charger connector into charge port on the pedal. 2. Then insert the charger plug into socket (AC100-240V). 3. After connected, if the charger indicator is red, it’s under normal charging process. If the indicator turns green, it means it’s fully charged. (The best full charging status is 2hours after the indicator turns green.)
CHARGE PORT’S POSITION
Charge Port
TIPS: Make sure all connectors are in right position while charging.
-9-
ADJUSTMENT OF REAR BUMPER STRENGTH
Strength of rear bumper can be adjusted. There is a bumper under the rear side of pedal. As shown in the above figure, there is a nut on the front part of bumper which can be adjusted. Use a open spanner to loosen the nut a little, then the bumper will go soft. Tighten the nut, then the bumper will go strong. It’s suggested that the bumper can not be too soft.
ADJUSTMENT OF REAR DISC BRAKE
Release the screw on the disc brake by a spanner. Push the rear corner of disc brake forward to appropriate position, then tighten the screw with spanner.
- 10 -
OPERATION
Battery quantity and speed are shown according to electric scooter s riding status. TIME, TRIP and ODO are shown according to functions chosen.
Press
button 3 seconds to start the speedometer system. Then the LED screen will light on and
show the standby status.
Press
button shortly, then the electric scooter will display or shine present gear L1, L2, or L3. L3 is
the fastest gear, while L1 the lowest. At this time, if press L2, and L3. Press
shortly, mode gear will change among L1,
button for 5 seconds, then the gear will save by itself and exit. Gear setting has
memory function. While start the scooter next time, the set gear will run automatically. Under the circumstances of full battery and loading below 70kg, speeds of every gear is as followed: L1: Maximum speed is around 15km/h. L2: Maximum speed is around 20km/h. L3: Maximum speed is around 25km/h.
Press
button to enter into single trip display, and icon “TRIP” is lightened. Value area shows 4
integrals and 1 decimal. For example “0123.4” means single trip is 123.4km. Under this interface, press
Press
button for 3 seconds, the single trip value will be cleared.
button to enter into accumulated trip display interface, and icon “ODO” is lightened. Value
area shows 5 integrals. For example “12345” means total trip is 12345km. Total trip value is the accumulated trip value of the scooter, and it can not be cleared.
Press
button to enter into charging frequency display interface. Value area shows 5 integrals. For
example 00018 means the battery has been charged and used for 18 times. When the battery is charged after the electricity quantity of the scooter is lower than 30% of total quantity, it’s counted as one charging. Under this interface, pressing mode button shortly can help you go back to time display interface.
Press
button to enter into time display interface, and icon “TIME” is lightened. Initial time display
format is “MM:SS”. First two integrals shows minutes, while rear two integrals seconds. When time display arrives at “99:59”, that is 99 minutes 59 seconds, it will switch to “HH:MM” format, which means first two integrals show hours and rear two integrals minutes.
- 11 -
PARAMETERS PARAMETER NO. 1
DEFAULT VALUE 0
MINIMUM VALUE 0
DESCRIPTION Start mode. 0= zero start, 1=non zero start, default is 0. Limited speed. The unit is 2 25 0km/h 60km/h km/h. 0 means no limit. Default value is 25km/h. Wheel diameter. The unit is 3 10 4inch 40inch inch. Default value is 10 inch. Speed testing magnetic steel 4 30 1 100 number. Default value is 1. 1st gear’s maximum duty 5 60 30% 100% cycle. The unit is %. Default value is 60%. 2nd gear’s maximum duty 6 80 30% 100% cycle. The unit is %. Default value is 80%. 3rd gear’s maximum duty 7 100 30% 100% cycle. The unit is %. Default value is 100%. Backup parameter 1 8 0 0 255 Backup parameter 2 9 0 0 255 Backup parameter 3 10 (1) 0 0 255 Backup parameter 4 11 (1) 0 0 255 Power voltage choosing. Three 12 (1) 36 24V 48V choices only, 24V, 36V, 48V. Time to power off 13 (1) 90 0S 600S automatically. The unit is second. Default value is 90 seconds. For speedometer version 2.1. 14 (1) 40 5km/h 100km/h Full scale speed value. The unit is km/h. Default value is 40km/h. For speedometer version 2.2. 14 (1) 5 0% 30% Trip calculation coefficient (the increased percentage value). ODO cleared. When set data 15 (1) 0 0 999 equals x, and exit after confirmation, ODO data is cleared. Display value is 2.1 or 2.2. It 0 2.1/2.2 can not be adjusted. Notes: 1. As parameter no. shows only 1 digital, parameter no.s 10-15 are shown by A, B, C, D, E, F. 2. Please contact manufacturer for ODO clearing code.
- 12 -
MAXIMUM VALUE 1
The speedometer on this scooter can read faults automatically. Faults code table Fault Code
Description
99
Speedometer’s receiving wire is faulty.
98
Speedometer’s sending wire is faulty.
01
Motor’s phase wire is short-circuited. Or the controller is faulty.
02
Twist handlebar is abnormal.
03
Motor’s phase wire is faulty.
04
Motor’s hall sensor is faulty.
05
Brake faulty.
06
Battery is low.
07
Motor is locked.
08
Backup 1
09
Backup 2
Power off automatically If there is no operation to the speedometer and the throttle is released totally (speed is zero) for over 90 seconds, the system will power off automatically to enter into power saving mode. Press
button for
3 seconds can turn on the system again.
Start up The start method of this scooter is non zero start, which means that before starting the scooter, one foot should be put on the scooter while the other on ground and kick the ground to give assistance to the scooter, then accelerate the scooter by hooking the throttle to start the scooter. After the scooter is started, throttle can be used to control the scooter’s speed.
- 13 -
MAINTENANCE LUBRICATION 1. Dip into the folding sleeves small quantity of lubrication for maintenance every 6 months. 2. Anti-rust oil can not be used for lubricating. 3. Front wheel, rear wheel, and disc brake do not need lubrication. 4. For any doubts, please consult your dealer.
If the scooter can not be operated, please check that you have the following actions done: 1. The power is on. 2. The battery has enough electricity. 3. Brake lever is released. 4. All ports and connectors are clean and well connected.
If the faults and damages are caused by the following reasons, it’s not included within warranty coverage even it’s within warranty period: 1. It’s not used and maintained according to users manual. 2. The scooter is damaged because of dangerous actions or breaking laws and regulations. 3. The scooter is modified at will, and non original parts are used. 4. Ride the scooter on abnormal roads. 5. The scooter is used for business or rental, or used improperly. 6. Force majeure. 7. The scooter is exposed outside for longtime, which caused fast aging and malfunction of the product.
TIPS: Do not ride after drink. Do not drink if ride.
- 14 -
PRODUCT’S SPECIFICATIONS AND PARAMETERS Type
X1
Dimensions
106*25*38
Wheelbase
810mm
Scooter weight
12kg/13kg
Maximum loading
100kg
Maximum speed
15-25km/h
Climbing ability
15°
Battery type
Lithium battery
Standard voltage
36V
Battery capacity
7.5AH
Endurance
25km
Type
DC brush-less motor
Rated output power
350W
Maximum rotating speed
1200rpm
Rated voltage
24V
Maximum output torque
9.5N.m
Input voltage
AC100-240V
Output current(DC)
2A
Charging time
4-6 hours
Electricity quantity consumption for one charge
0.5 kilowatt hour
WHEELS
Type
8inch, PU, high elastic, solid
LIGHT TYPE
LED
Light with horn
SPECIFICATIONS
PERFORMANCE
BATTERY PARAMETER
MOTOR PARAMETER
CHARGER PARAMETER
- 15 -
WARRANTY COVERAGE PARTS Motor
QUALITY ISSUE Motor can not use.
WARRANTY PERIOD
SERVICE
One year
Free service
Three months
Free service
Naturally (impacts etc. Speedometer
due to external force are not included.)
Controller
Faulty under normal using
Six months
Free service
Charger
Faulty under normal using
One year
Free service
One year
Free service
Two years
Free service
Can not charge under Lithium battery normal using Scooter body is deformed Body construction
or fractured and can not be used any more under normal using.
- 16 -